Use the new ieee80211_get_channel() function instead of open-coding it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 able to send a phase1 key for TKIP
decryption.
This is needed for drivers that don't do the rekeying by themselves
(i.e. iwlwifi). Upon IV16 wrap around, the packet is decrypted in SW,
if decryption is ok, mac80211 calls to update_tkip_key with a new
phase 1 RX key.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 able to compute a TKIP key from an skb.
The requested key can be a phase 1 or a phase 2 key.
This is useful for drivers who need to provide tkip key to their
HW to enable HW encryption.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette pointed out that with the sta_info RCU-ification
the behaviour here changed and the conf_tx callback is
now invoked under RCU read lock. That is not necessary so
this patch restores the original behaviour
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 MLME requires restarting timers after a scan
completes but this wasn't done when hardware scan offload
was added, so add it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Bill Moss <bmoss@clemson.edu>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip properly entries whose dev does not match.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Postponing the deletion is not really useful anymore.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids dereferencing a no longer existing struct mesh_path.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pointed out by Johannes Berg.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes all the mesh related endianness warnings reported by sparse. As
they were the reason why Johannes marked mesh as BROKEN, that flag has been
removed.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Today I hit one of my new WARN_ONs in the mac80211 code because
a key wasn't being freed correctly. After wondering for a while
I finally tracked it to the fact that STA keys aren't added to
the per-sdata key list correctly, they are supposed to always be
on that list, not just for default keys. This patch fixes that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a bug I introduced when mesh is enabled: sta_info_destroy()
will end up calling cancel_timer() on a timer that has never been
initialized because the timer is only initialized in mesh_plink_alloc(),
not in sta_info_alloc(). This patch moves the initialization of all mesh
related fields into sta_info_alloc(), adds a bit of sanity checking to
the cfg80211 handlers and sta_info_insert() and makes mesh_plink_alloc()
a static helper function that is only used from the mesh plink code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Quite a while ago I started this book. The required kernel-doc
patches have since gone into the tree so it is now possible to
build the book in mainline.
The actual documentation is still rather incomplete and not all
things are linked into the book, but this enables us to edit
the documentation collaboratively, hopefully driver authors can
add documentation based on their experience with mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis pointed out that this path is going to be freed right
away anyway so there's no point in assigning next_hop.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we take down an interface, we need to remove the STA info
items that belong to it because otherwise we might invoke a
sta_notify() callback in the driver when we later delete the
STA entries, but in that case the driver will already have
removed its knowledge of the interface they belonged to leading
to confusion. Also, we could invoke the set_tim() callback after
the driver removed its knowledge of the interface, which can
lead to a crash if it requests a beacon with a then-invalid vif
pointer!
A side effect of this patch is that, because it was easier, it
disallows changing the WDS peer while an interface is up. Should
that actually be necessary, it can be added back, but the WDS
peer STA entry may not be added while the interface is UP so for
now I've simplified the WDS peer's STA entry lifetime management.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the sta_info struct and documents how
each set of variables is locked. Notably, flags locking is
completely missing. It also adds kernel-doc for some (but
not all yet) members of the struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_info_add() has two functions: allocating a station info
structure and inserting it into the hash table/list. Splitting
these two functions allows allocating with GFP_KERNEL in many
places instead of GFP_ATOMIC which is now required by the RCU
protection. Additionally, in many places RCU protection is now
no longer needed at all because between sta_info_alloc() and
sta_info_insert() the caller owns the structure.
This fixes a few race conditions with setting initial flags
and similar, but not all (see comments in ieee80211_sta.c and
cfg.c). More documentation on the existing races will be in
a follow-up patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes access to the STA hash table/list use RCU to protect
against freeing of items. However, it's not a true RCU, the
copy step is missing: whenever somebody changes a STA item it
is simply updated. This is an existing race condition that is
now somewhat understandable.
This patch also fixes the race key freeing vs. STA destruction
by making sure that sta_info_destroy() is always called under
RTNL and frees the key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split it into ieee80211_tx_data and ieee80211_rx_data to clarify
usage/flag usage and remove the stupid union thing.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Three __le16s followed by an enum (int) leave a two-byte hole
of padding which we can use for two of the other fields.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accidentally copied in a __mesh_plink_deactivate, noticed by Luis
Carlos Cobo.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moves another ifdef into the sta_info header file in favour of
compiling more code even w/o CONFIG_MAC80211_MESH.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This needs to be exported because rate control algorithms
can be modular.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This clarifies that the mesh networking code is currently
based on Draft 1.08 of the 802.11 Mesh Networking amendment.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This inserts a missing break statement which, if hit, would cause
the code to fall-through and unlock a spinlock twice. Noticed via
sparse's "lock count wrong in basic block" warning and careful
code inspection.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently marked BROKEN because of endianness problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes missing unlocks noticed by sparse.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various cleanups, reducing the #ifdef mess and other things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This completes the mesh interface handling code and a few other
bits about the mac80211 module.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to allow adding mesh interfaces and configuring
mesh peers etc. Also, it adds code for station dumping.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the debugfs code for mesh statistics and configuration
parameters. Please note that generic support for r/w debugfs attributes has been
added.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file implements the on-demand Hybrid Wireless Mesh Protocol, at this moment
using hop-count as the metric. When no mesh path exists for a given destination
or the mesh path is not active, frames addressed to that destination will be
queued and a Path Request frame will be sent. Queued frames will be sent when
the path is resolved (usually after reception of a Path Response) or discarded
if discovery times out. Path Requests will also be sent to refresh paths that
are being used and are close to expiring.
Path Errors are sent when a path discovery process triggered by the attempt to
forward a frame originated in a different mesh point times out. Path Errors are
also sent when a peer link is determined to be unreachable because of high error
rates.
Multiple destination support in Path Requests and Path Errors and precursors
have not been implemented yet.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh path table associates destinations with the next hop to reach them. The
table is a hash of linked lists protected by rcu mechanisms. Every mesh path
contains a lock to protect the mesh path state.
Each outgoing mesh frame requires a look up into this table. Therefore, the
table it has been designed so it is not necessary to hold any lock to find the
appropriate next hop.
If the path is determined to be active within a rcu context we can safely
dereference mpath->next_hop->addr, since it holds a reference to the sta
next_hop. After a mesh path has been set active for the first time it next_hop
must always point to a valid sta. If this is not possible the mpath must be
deleted or replaced in a RCU safe fashion.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file implements mesh discovery and peer link establishment support using
the mesh peer link table provided in mesh_plinktbl.c.
Secure peer links have not been implemented yet.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This includes support for mesh network scanning. The ugly code in
ieee80211_sta_scan_result() is my approach to work around wext. This has been
tested with wireless tools version 29 and works as expected (the new interface
mode is just not shown).
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Includes integration in struct sta_info of mesh peer link elements, previously
on their own mesh peer link table.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the TX/RX paths in mac80211 to support mesh interfaces.
This code will be cleaned up later again before being enabled.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two important features coded in mesh.c are:
Recently Multicast Cache: in on-demand HWMP, multicast traffic is retransmitted
by every receiving node. Even though a mesh TTL counter avoids infinite loops,
it is also necessary to avoid traffic explosion by keeping a cache of multicast
mesh frame that have been received recently. With this feature, maximum number
of retransmissions of a multicast frame for the case of N nodes within the range
of each other would be N. Without it, the maximum number of retransmissions
would be in the order of N^(MESH_TTL - 1).
Code to support mesh tables.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added support for mesh id and mesh path operation as well as
station structure dumping.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge rate_control_pid_shift_adjust() to rate_control_pid_adjust_rate()
in order to make the learning algorithm aware of constraints on rates. Also
add some comments and rename variables.
This fixes a bug which prevented 802.11b/g non-AP STAs from working with
802.11b only AP STAs.
This patch was originally destined for 2.6.26, and is being backported
to fix a user reported problem in post-2.6.24 kernels.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though I thought about it a lot and had also tested it, some
of my recent changes in the key code broke replacing keys, making
the kernel oops because a key is removed from a list while not on
it.
This patch fixes that using the list as an indication whether or
not the key is on it (an empty list means it's not on any list.)
Also, this patch fixes hw accel enabling, the check for not doing
hw accel when the interface is down was lost and is restored by
this.
Additionally, move adding the key to the list into the function
__ieee80211_key_replace() for more consistency.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to RCU-ify sta_info, we need to be able to allocate
a key without linking it to an sdata/sta structure (because
allocation cannot be done in an rcu critical section). This
patch splits up ieee80211_key_alloc() and updates all users
appropriately.
While at it, this patch fixes a number of race conditions
such as finally making key replacement atomic, unfortunately
at the expense of more complex code.
Note that this patch documents /existing/ bugs with sta info
and key interaction, there is currently a race condition
when a sta info is freed without holding the RTNL. This will
finally be fixed by a followup patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These things aren't used and the only possible use is within
rate control algorithms, however those can, if they need it,
keep track of it in their private data. last_ack_ms isn't
even updated so completely useless.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If ieee80211_if_reinit() is called from ieee80211_unregister_hw()
then it is possible that the driver will still request a beacon
(it is allowed to until ieee80211_unregister_hw() has returned.)
This means we need to use an RCU-protected write to the beacon
information even in this function.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two errors introduced by
commit 19d35612f3cd7f60dd9174c0100584e21f5a1025
Author: Bruno Randolf <bruno@thinktube.com>
Date: Mon Feb 18 11:21:36 2008 +0900
mac80211: enable IBSS merging
The first error is an endianness problem that sparse found and
the second is a build failure when CONFIG_MAC80211_IBSS_DEBUG
is not set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When print_mac() was marked as __pure to avoid emitting a function
call in pr_debug() scenarios, a warning in this code surfaced since
it relies on the fact that the buffer is modified and doesn't use
the return value. This patch makes it use the return value instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disallow having more than one IBSS interface up at any time
because of beacon distribution issues, and for now also disallow
having more than one IBSS/STA interface up at the same time
because we use the master interface's BSS struct which would
be completely corrupted when we have more than one up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a STA structure is added, it is often checked whether it
already exists before adding it. This, however, isn't done
atomically so there is a race condition that could lead to two
STA structures being added with the same MAC address. This
patch changes sta_info_add() to return an ERR_PTR in case
of failure and adds the failure mode -EEXIST when the STA
already exists.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the code for TX filtered frames, splitting it out to
a new function to handle those cases, making the clear instruction
a flag and renaming a few things to be easier to understand and
less Atheros hardware specific. Finally, it also makes the comments
explain more.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configuration variables are only available to the preprocessor
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This consolidates all TIM handling code to avoid re-introducing
errors with the bitmap/set_tim order and to reduce code. While
reading the code I noticed a possible problem so I also added
a comment about that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM flag that is kept in each station's info is completely
useless, there's no code (aside from the debugfs display code)
checking it, hence it can be removed. While doing that, I noticed
that the TIM handling is broken when buffered frames expire, so
fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should be allowed to simply get a complete new beacon when
set_tim() is invoked (and set_tim() is required for drivers that
just want a beacon template!), so we need to update our own TIM
bitmap before calling set_tim() so that getting the beacon will
now get an already updated beacon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't really need to be a full int variable since it's
just a flag to indicate a PS-poll is in progress.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable IBSS cell merging. if an IBSS beacon with the same channel, same ESSID
and a TSF higher than the local TSF (mactime) is received, we have to join its
BSSID. while this might not be immediately apparent from reading the 802.11
standard it is compliant and necessary to make IBSS mode functional in many
cases. most drivers have a similar behaviour.
* move the relevant code section (previously only containing debug code) down
to the end of the function, so we can reuse the bss structure.
* we have to compare the mactime (TSF at the time of packet receive) rather
than the current TSF. since mactime is defined as the time the first data
symbol arrived we add the time until byte 24 where the timestamp resides, since
this is how the beacon timestamp is defined. as some some drivers are not able
to give a reliable mactime we fall back to use the current TSF, which will be
enough to catch most (but not all) cases where an IBSS merge is necessary.
* in IBSS mode we want to allow beacons to override probe response info so we
can correctly do merges.
* we don't only configure beacons based on scan results, so change that
message.
* to enable this we have to let all beacons thru in IBSS mode, even if they
have a different BSSID.
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this moves ieee80211_sta_join_ibss() up for the next patch (ibss merge).
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions time_before, time_before_eq, time_after, and time_after_eq are more robust for comparing jiffies against other values.
So following patch implements usage of the time_after() macro, defined at linux/jiffies.h, which deals with wrapping correctly
Cc: linux-wireless@vger.kernel.org
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This brain-damaged code just bothers me, fix it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes mac80211 to pass the burst time to conf_tx in txop
units rather than 0.1msec units. 0.1msec units are only required
by atheros hardware (according to current driver support), all
other drivers do other calculations or require the txop value.
Therefore, it results in fewer calculations and more precision
if we just pass the txop value through to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we want to go multiqueue, we will need to know the number of
queues the hardware has for registering the master netdev. This
number is only available in ieee80211_register_hw() rather than
ieee80211_alloc_hw(), so defer allocation of the master device to
ieee80211_register_hw().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix allows to control the number of bits that qdiscs book keeping
can be done for with respect to the qdisc pool
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds "cooked" monitor mode to mac80211. A monitor interface
in "cooked" mode will see all frames that mac80211 has not used
internally.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is some duplicated code that sits in front of each function
call to ieee80211_invoke_rx_handlers() that can very well be part
of that function if it gets slightly different arguments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't really make sense to have extra pointers to the RX/TX
handler arrays instead of just using the arrays directly, that
also allows us to make them static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Uninline ieee80211_invoke_rx_handlers to save .text space,
make the code more readable in some places and remove the
"optimisation" that is hit only very few times and unclear
to start with.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take advantage of the monitor configuration flags now provided by cfg80211.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows precise control over what a monitor interface shows.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some instances of RX_DROP mean that the frame was useless,
others mean that the frame should be visible in userspace
on "cooked" monitor interfaces. This patch splits up RX_DROP
and changes each instance appropriately.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The _DROP result will need to be split in the RX path but not
in the TX path, so for preparation split up the type into two
types, one for RX and one for TX. Also make sure (via sparse)
that they cannot be confused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge rate_control_pid_shift_adjust() to rate_control_pid_adjust_rate()
in order to make the learning algorithm aware of constraints on rates. Also
add some comments and rename variables.
This fixes a bug which prevented 802.11b/g non-AP STAs from working with
802.11b only AP STAs.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the 802.1X port acess control enable flag
since it is not required. Instead, set the authorized flag for
each station that we normally communicate with (WDS peers, IBSS
peers and APs we're associated to) and require hostapd to set
the authorized flag for all stations when port control is not
enabled.
Also, since I was working in that area, this documents station
flags and removes the unused "permanent" one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When checking for the next band to advance to, there
was an off-by-one error that could lead to an access
to an invalid array index. Additionally, the later
check for scan_band >= IEEE80211_NUM_BANDS is not
required since that will never be true.
This also improves the comments related to that code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These handlers do not really return a status and the compiler
can do a much better job when they're simply static functions
that it can inline if appropriate. Also makes the code shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the ability to handle delBA from recipient to initiator
during an A-MPDU session
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds A-MPDU status report per STA to the debugfs.
The option to de/activate A-MPDU through debugfs is also present.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch initialize A-MPDU MLME data for Tx sessions.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows qdisc support in A-MPDU Tx. a method to
handle QoS <-> TID switches is present in this patch.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the needed structures to describe the Tx aggregation MLME
per STA
new:
- struct tid_ampdu_tx: TID aggregation information (Tx)
changed:
- struct sta_ampdu_mlme: Tx aggregation information per TID and
dialog token creator were added
- struct sta_info: tid_to_tx_q added for tid<->tx queue mapping
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the API for 3 stages in A-MPDU Tx session flow:
- request mac80211 to start/stop A-MPDU Tx session for specific TID. such a
request should be issued by a load aware element, either mac80211 itself
or external element.
- requests by mac80211 to low-level driver to start/stop Tx aggregation.
notice that low level driver responds now with Starting Sequence Number.
- async feedback by low-level to mac80211 to inform that HW is ready for
next A-MPDU Tx state.
Changes in API to Rx A-MPDU were also made, reflected in iwlwifi changes as
well.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reworking the port access control code, I forgot multicast frames
and those are now always rejected because the destination station is
not known. This changes the code to allow through multicast frames and
also avoid the sta hash lookup (which is bound to fail) for them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only BSS_CHANGED_ASSOC was set in the 'changed' bitmask. Assignment to
bss_conf.assoc was absent.
This patch assign value to bss_conf.assoc according the association state.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "goto end;" part definitely must not be rate limited.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On the initial device-open we need to defer the hardware reconfiguration
after we incremented the open_count, because the hw_config checks this flag
and won't call the lowlevel driver in case it is zero.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the EXPERIMENTAL dependency, as the existing mac80211
features are stable.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The error handling in ieee80211_init() is broken when any of
the built-in rate control algorithms fail to initialise, fix
it and rename the error labels.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the rate control algorithms are built-in, their exit
functions can be called from mac80211's init function so
they cannot be marked __exit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver authors should be aware of the alignment requirements, but
not everybody cares about the warning. This patch makes it depend
on a new Kconfig symbol MAC80211_DEBUG_PACKET_ALIGNMENT which can
be enabled regardless of MAC80211_DEBUG and is recommended for
driver authors (only). This also restricts the warning to data
packets so other packets need not be realigned to not trigger the
warning.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a wrong condition for null qos data frames, causing us to
drop data frames needed for reordering as well.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I introduced the alignment warning I forgot the A-MSDU case which
has a different requirement because each frame contains 14-byte 802.3
headers in front of the IP payload. This patch moves the alignment
warning to a place where we know whether we're dealing with an A-MSDU
frame and adjusts it accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert packet schedulers to use the netlink API. Unfortunately a gradual
conversion is not possible without breaking compilation in the middle or
adding lots of casts, so this patch converts them all in one step. The
patch has been mostly generated automatically with some minor edits to
at least allow seperate conversion of classifiers and actions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds static declarations to functions in the Rx flow in order to
eliminate sparse errors
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix last_sample initialization. kzalloc'ing the per-STA data wasn't enough,
as jiffies can assume negative values as well. This fixes a bug which
prevented correct PID operation for a while after booting.
Thanks to Michael Buesch for reporting this.
Reported-and-tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c7a51bda ("mac80211: restructure __ieee80211_rx") extracted
__ieee80211_rx_handle_packet out of __ieee80211_rx and hence changed
the locking rules for __ieee80211_rx_handle_packet(), it is now
invoked under RCU lock. There is, however, one instance left where
it contains an rcu_read_unlock() in an error path, which is a bug.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch assigns correct TID to frames transmitted between
two stations in the same BSS in AP mode.
The problem is that skb->protocol is not set to ETH_P_IP and it is wrong
to use that field at this stage.
The fix compares the LLC/Protocol headers explicitly to check if the
encapsulated frame is IP frame
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a warning print from ieee80211_sta_stop_rx_ba_session
in case the tid is inactive when interface goes down.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check to insure that Rx A-MPDU will be stopped only
for the proper device.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before calling update_beacon() mac80211 must
initialize the control.vif pointer so it can
be used by the driver to determine which
interface is trying to send the beacon.
v2: ieee80211_beacon_get() should also initialize the
vif pointer since it can be called by mac80211 internally
before calling config_interface().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mattias Nissler's "clean up rate selection" patch incorrectly changes
the behavior of txrate setting in sta_info. This patch backs out parts
of the rate selection consolidation in order to fix this issue for now.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements station handling from userspace via cfg80211
in mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements the cfg80211 hooks for configuring beaconing
on an access point interface in mac80211. While doing so, it fixes
a number of races that could badly crash the machine when the
beacon is changed while being requested by the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have a seperate LED which indicates if the radio is
enabled or not. This adds a LED trigger to mac80211 where drivers
can hook into when they are interested in radio status changes.
v2: Check hw.conf.radio_enabled when calling start().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I would argue that mac80211 should handle fixed rates outside the rate
control code, which would also allow them to take effect immediately
instead of during the rate control callback, but this is pretty close
to correct.
Signed-Off-By: Andy Lutomirski <luto@myrealbox.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes mac80211's Kconfig/Makefile to:
* select between the PID and the SIMPLE rate control
algorithm as default
* always allow tri-state for the rate control algorithms,
building those that are selected 'y' into the mac80211
module (if that is a module, otherwise all into the kernel)
* force the default rate control algorithm to be built into
mac80211
It also makes both rate control algorithms proper modules again
with MODULE_LICENSE etc.
Only if EMBEDDED is the user allowed to select "NONE" as default
which will cause no algorithm to be selected, this will work
only when the driver brings one itself (e.g. iwlwifi drivers).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch opens the flow to DELBA management frames, and handles end
of A-MPDU session produced by this event.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to handle Block Ack Request
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles the reordering of the Rx A-MPDU.
This issue occurs when the sequence of the internal MPDUs is not in the
right order. such a case can be encountered for example when some MPDUs from
previous aggregations were recieved, while others failed, so current A-MPDU
will contain a mix of re-transmited MPDUs and new ones.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initialize A-MPDU MLME data for Rx sessions.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the basic needed abilities and functions for A-MPDU Rx session
changed functions:
- ieee80211_sta_process_addba_request - Rx A-MPDU initialization enabled
- ieee80211_stop - stops all A-MPDU Rx in case interface goes down
added functions:
- ieee80211_send_delba - used for sending out Del BA in A-MPDU sessions
- ieee80211_sta_stop_rx_BA_session - stopping Rx A-MPDU session
- sta_rx_agg_session_timer_expired - stops A-MPDU Rx use if load is too
low
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the needed structures to describe the Rx aggregation MLME per STA
new:
- struct tid_ampdu_rx: TID aggregation information (Rx)
- struct sta_ampdu_mlme: MLME aggregation information for STA
changed:
- struct sta_info: ampdu_mlme added to describe A-MPDU MLME per STA,
and timer_to_tid added to map timer id into TID
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes a separation between Rx frame pre-handling which stays in
__ieee80211_rx and Rx frame handlers, moving to __ieee80211_rx_handle_packet.
Although this separation has no affect in regular mode of operation, this kind
of mechanism will be used in A-MPDU frames reordering as it allows accumulation
of frames during pre-handling, dispatching them to later handling when necessary.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to not be.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the rate control interval definition. Thanks to Mattias Nissler for
spotting this out.
Cc: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When this function returns != CONTINUE, it needs to put the
station struct it has acquired. Hence, having this unused
variable is not just superfluous but also misleading.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set a better value for percentage target for failed frames. The previous value
slowed down too much rate increases in case of permanently low activity. While
at it, increase readability.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug which caused uncorrect refcounting of PHYs in mac80211. Thanks to
Johannes Berg for spotting this out.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify and fix rate_control_pid_shift_adjust(). A bug prevented correct
mapping of sorted rates, and readability was seriously flawed.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a kerneldoc description for parameters which are tunable through debugfs.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the non-shifted target_pf value to debugfs, so that it's human-readable.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem with rx handling on multiple interfaces. Especially
when using hardware-scanning and a wireless driver (i.e. iwlwifi) which is
able to receive data while scanning.
The rx handlers can modify the skb and the frame control field (see
ieee80211_rx_h_remove_qos_control) but since every interface gets its own
copy of the skb each should get its own copy of rx.fc too.
In my case the wlan0-interface did not remove the qos-control from the frame
because the corresponding flag in rx.fc was already removed while processing
the frame on the master interface. Therefore somehow corrupted frames were
passed to the userspace.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the standard, the field cannot be present, so don't
try to interpret it either.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the decision making about whether a frame is encrypted
with a certain algorithm up into the TX handlers rather than having it
in the crypto algorithm implementation.
This fixes a problem with the radiotap injection code where injecting
a non-data packet and requesting encryption could end up asking the
driver to encrypt a packet without giving it a key.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the required cfg80211 callback in mac80211
to allow userspace to get station statistics.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements cfg80211's get_key() to allow retrieving the sequence
counter for a TKIP or CCMP key from userspace. It also cleans up and
documents the associated low-level driver interface.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary hooks to mac80211 to allow userspace
to edit keys with cfg80211 (through nl80211.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are various decisions influencing the decision whether to buffer
a frame for after the next DTIM beacon. The "do we have stations in PS
mode" condition cannot be tested by the driver so mac80211 has to do
that. To ease driver writing for hardware that can buffer frames until
after the next DTIM beacon, introduce a new txctl flag telling the
driver to buffer a specific frame.
While at it, restructure and comment the code for multicast buffering
and remove spurious "inline" directives.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is only used locally.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch left only one user of the ieee80211_is_eapol()
function and that user can be eliminated easily by introducing
a new "frame is EAPOL" flag to handle the frame specially (we
already have this information) instead of doing the (expensive)
ieee80211_is_eapol() all the time.
Also, allow unencrypted frames to be sent when they are injected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans up the eapol frame handling and some related code in the
receive and transmit paths. After this patch
* EAPOL frames addressed to us or the EAPOL group address are
always accepted regardless of whether they are encrypted or not
* other frames from a station are dropped if PAE is enabled and
the station is not authorized
* unencrypted frames (except the EAPOL frames above) are dropped if
drop_unencrypted is enabled
* some superfluous code that eth_type_trans handles anyway is gone
* port control is done for transmitted packets
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds all the tunable parameters used by rc80211_pid to debugfs for easy
testing and tuning.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a new debugfs file from which rate control relevant events can be
read one event per line. The output includes the current time, so graphs can be
created showing the rate control parameters. This helps in evaluating and
tuning rate control parameters. While at it, we split headers and code for
better readability.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a PID sharpening factor for faster response after
association and low activity events.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a learning algorithm in order for the PID controller
to learn how to map adjustment values to rates. This is better described in
code comments.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the new PID TX rate control algorithm the default instead of the
rc80211_simple rate control algorithm. The simple algorithm was flawed in
several ways: it wasn't responsive at all and didn't age the information it was
relying on properly. The PID algorithm allows us to tune characteristics such
as responsiveness by adjusting parameters and was found to generally behave
better.
The default algorithm can be overridden to select simple instead. Which
ever algorithm is the default is included as part of the mac80211
module automatically. The other algorithm (simple vs. pid) can
be selected for inclusion as well. If EMBEDDED is selected then
the choice is available to have no default specified and neither
algorithm included in mac80211. The default algorithm can be set
through a modparam.
While at it, mark rc80211-simple as deprecated, and schedule it
for removal.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rate control algorithm based on a PID controller. It samples the
percentage of failed frames over time, feeds the result into the controller and
uses its output to control the TX rate.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some code out of rc80211_simple since it's probably needed for all rate
selection algorithms, and fix iwlwifi accordingly. While at it, clean up the
rate_control_get_rate() interface.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
