Current code follows the framework that has been in the transports
from the beginning where initial link-side controller connect occurs
as part of "creating the controller". Thus that first connect fully
talks to the controller and obtains values that can then be used in
for blk-mq setup, etc. It also means that everything about the
controller is fully know before the "create controller" call returns.
This has several weaknesses:
- The initial create_ctrl call made by the cli will block for a long
time as wire transactions are performed synchronously. This delay
becomes longer if errors occur or connectivity is lost and retries
need to be performed.
- Code wise, it means there is a separate connect path for initial
controller connect vs the (same) steps used in the reconnect path.
- And as there's separate paths, it means there's separate error
handling and retry logic. It also plays havoc with the NEW state
(should transition out of it after successful initial connect) vs
the RESETTING and CONNECTING (reconnect) states that want to be
transitioned to on error.
- As there's separate paths, to recover from errors and disruptions,
it requires separate recovery/retry paths as well and can severely
convolute the controller state.
This patch reworks the fc transport to use the same connect paths
for the initial connection as it uses for reconnect. This makes a
single path for error recovery and handling.
This patch:
- Removes the driving of the initial connect and replaces it with
a state transition to CONNECTING and initiating the reconnect
thread. A dummy state transition of RESETTING had to be traversed
as a direct transtion of NEW->CONNECTING is not allowed. Given
that the controller is "new", the RESETTING transition is a simple
no-op. Once in the reconnecting thread, the normal behaviors of
ctrl_loss_tmo (max_retries * connect_delay) and dev_loss_tmo will
apply before the controller is torn down.
- Only if the state transitions couldn't be traversed and the
reconnect thread not scheduled, will the controller be torn down
while in create_ctrl.
- The prior code used the controller state of NEW to indicate
whether request queues had been initialized or not. For the admin
queue, the request queue is always created, so there's no need to
check a state. For IO queues, change to tracking whether a successful
io request queue create has occurred (e.g. 1st successful connect).
- The initial controller id is initialized to the dynamic controller
id used in the initial connect message. It will be overwritten by
the real controller id once the controller is connected on the wire.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We already check for started commands in all callbacks, but we should
also protect against already completed commands. Do this by taking
the checks to common code.
Acked-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Current code will set DNR if the controller is deleting or there is
an error during controller init. None of this is necessary.
Remove the code that sets DNR
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Provide a descriptive error in case an lport to rport association
isn't found when creating the FC-NVME controller.
Currently it's very hard to debug the reason for a failed connect
attempt without a look at the source.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
The nvmf_check_if_ready() checks that were added are very simplistic.
As such, the routine allows a lot of cases to fail ios during windows
of reset or re-connection. In cases where there are not multi-path
options present, the error goes back to the callee - the filesystem
or application. Not good.
The common routine was rewritten and calling syntax slightly expanded
so that per-transport is_ready routines don't need to be present.
The transports now call the routine directly. The routine is now a
fabrics routine rather than an inline function.
The routine now looks at controller state to decide the action to
take. Some states mandate io failure. Others define the condition where
a command can be accepted. When the decision is unclear, a generic
queue-or-reject check is made to look for failfast or multipath ios and
only fails the io if it is so marked. Otherwise, the io will be queued
and wait for the controller state to resolve.
Admin commands issued via ioctl share a live admin queue with commands
from the transport for controller init. The ioctls could be intermixed
with the initialization commands. It's possible for the ioctl cmd to
be issued prior to the controller being enabled. To block this, the
ioctl admin commands need to be distinguished from admin commands used
for controller init. Added a USERCMD nvme_req(req)->rq_flags bit to
reflect this division and set it on ioctls requests. As the
nvmf_check_if_ready() routine is called prior to nvme_setup_cmd(),
ensure that commands allocated by the ioctl path (actually anything
in core.c) preps the nvme_req(req) before starting the io. This will
preserve the USERCMD flag during execution and/or retry.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.e>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
When reattaching to a removed remoteport that has not yet been
fully deleted as it's waiting for reconnect timeouts, be sure to
re-set the ports nport id and role.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Another abort race: An io request is started, becomes active,
and is attempted to be started with the lldd. At the same time
the controller is stopped/torndown and an itterator is run to
abort the ios. As the io is active, it is added to the outstanding
aborted io count. However on the original io request thread, the
driver ends up rejecting the io due to the condition that induced
the controller teardown. The driver reject path didn't check whether
it was in the outstanding io count. This left the count outstanding
stopping controller teardown.
Correct by, in the driver reject case, setting the state to
inactive and checking whether it was in the outstanding io count.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The current nvme_fc code, when an io times out, will abort the io
on the fc link, then call the error recovery routine to reset the
controller. It is during the reset of the controller that the
transport will wait for all ios to be aborted before sending a
Disconnect LS to the target.
However, the reset routine only waits for the io which it generates
the abort for to complete. Any io that was aborted just prior to the
reset isn't in it's list to wait for. Thus the Disconnect is getting
sent before the aborts have completed.
Correct by removing the abort in the timeout handler. The reset will
generate the abort. At that point the timeout handler can be simplified
to request the reset (via the error handler) and restart the timeout
timer.
Also fixes a small typo in a comment in the reset handler.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If there are errors during initial controller create, the transport
will teardown the partially initialized controller struct and free
the ctlr memory. Trouble is - most of those errors can occur due
to asynchronous events happening such io timeouts and subsystem
connectivity failures. Those failures invoke async workq items to
reset the controller and attempt reconnect. Those may be in progress
as the main thread frees the ctrl memory, resulting in NULL ptr oops.
Prevent this from happening by having the main ctrl failure thread
changing state to DELETING followed by synchronously cancelling any
pending queued work item. The change of state will prevent the
scheduling of resets or reconnect events.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvme_delete_ctrl can be called from various contexts in parallel,
and cause duplicated information prints, even though the specific
context doesn't perform the actual removal. Instead, print the
information when the actual removal occurs.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Corrected four outstanding issues in the transport around sqsize.
1: Create Connection LS is sending the 1's-based sqsize, should be
sending the 0's-based value.
2: allocation of hw queue is using the 0's-base size. It should be
using the 1's-based value.
3: normalization of ctrl.sqsize by MQES is using MQES+1 (1's-based
value). It should be MQES (0's-based value).
4: Missing clause to ensure queue_count not larger than ctrl->sqsize.
Corrected by:
Clean up routines that pass queue size around. The queue size value is
the actual count (1's-based) value and determined from ctrl->sqsize + 1.
Routines that send 0's-based value adapt from queue size.
Sset ctrl->sqsize properly for MQES.
Added clause to nsure queue_count not larger than ctrl->sqsize + 1.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <keith.busch@intel.com>
There was some old cold that dealt with complete_rq being called
prior to the lldd returning the io completion. This is garbage code.
The complete_rq routine was being called after eh_timeouts were
called and it was due to eh_timeouts not being handled properly.
The timeouts were fixed in prior patches so that in general, a
timeout will initiate an abort and the reset timer restarted as
the abort operation will take care of completing things. Given the
reset timer restarted, the erroneous complete_rq calls were eliminated.
So remove the work that was synchronizing complete_rq with io
completion.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
During reset handling, there is live io completing while the reset
is taking place. The reset path attempts to abort all outstanding io,
counting the number of ios that were reset. It then waits for those
ios to be reclaimed from the lldd before continuing.
The transport's logic on io state and flag setting was poor, allowing
ios to complete simultaneous to the abort request. The completed ios
were counted, but as the completion had already occurred, the
completion never reduced the count. As the count never zeros, the
reset/delete never completes.
Tighten it up by unconditionally changing the op state to completed
when the io done handler is called. The reset/abort path now changes
the op state to aborted, but the abort only continues if the op
state was live priviously. If complete, the abort is backed out.
Thus proper counting of io aborts and their completions is working
again.
Also removed the TERMIO state on the op as it's redundant with the
op's aborted state.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
In pci transport, this state is used to mark the initialization
process. This should be also used in other transports as well.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
This status is returned from driver to block layer if device related
resource is unavailable, but driver can guarantee that IO dispatch
will be triggered in future when the resource is available.
Convert some drivers to return BLK_STS_DEV_RESOURCE. Also, if driver
returns BLK_STS_RESOURCE and SCHED_RESTART is set, rerun queue after
a delay (BLK_MQ_DELAY_QUEUE) to avoid IO stalls. BLK_MQ_DELAY_QUEUE is
3 ms because both scsi-mq and nvmefc are using that magic value.
If a driver can make sure there is in-flight IO, it is safe to return
BLK_STS_DEV_RESOURCE because:
1) If all in-flight IOs complete before examining SCHED_RESTART in
blk_mq_dispatch_rq_list(), SCHED_RESTART must be cleared, so queue
is run immediately in this case by blk_mq_dispatch_rq_list();
2) if there is any in-flight IO after/when examining SCHED_RESTART
in blk_mq_dispatch_rq_list():
- if SCHED_RESTART isn't set, queue is run immediately as handled in 1)
- otherwise, this request will be dispatched after any in-flight IO is
completed via blk_mq_sched_restart()
3) if SCHED_RESTART is set concurently in context because of
BLK_STS_RESOURCE, blk_mq_delay_run_hw_queue() will cover the above two
cases and make sure IO hang can be avoided.
One invariant is that queue will be rerun if SCHED_RESTART is set.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
When connectivity is lost to a device, the association is terminated
and the blk-mq queues are quiesced/stopped. When connectivity is
re-established, they are resumed.
If connectivity is lost for a sufficient amount of time that the
controller is then deleted, the delete path starts tearing down queues,
and eventually calling nvme_ns_remove(). It appears that pending
commands may cause blk_cleanup_queue() to never complete and the
teardown stalls.
Correct by starting the ns queues after transitioning to a DELETING
state, allowing pending commands to be flushed with io failures. Thus
the delete path is clear when reached.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When connectivity is lost to a device, the association is terminated
and the blk-mq queues are quiesced/stopped. When connectivity is
re-established, they are resumed.
If an admin command is received while connectivity is list, the ioctl
queues the command on the admin_q and the command stalls (the thread
issuing the ioctl hangs/waits). if the connectivity is lost long
enough such that the controller is then deleted, the delete code
makes its calls to initiate the delete, which then expects the core
layer to call the transport when all references are removed and the
controller can be freed. Unfortunately, nothing in this path dequeued
the admin command, so a reference sits outstanding and things stop,
hanging the delete indefinitely.
Correct by unquiescing the admin queue in the delete association. This
means any admin command (which should only be from an ioctl) issued
after connectivity is lost will detect the controller is in a
reconnecting state and will (fast) fail the command. Thus, a pending
reference can no longer be created. Once connectivity is re-established,
a new ioctl/admin command would see proper device state and function again.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
NVMe transport driver module unload may (and usually does) trigger
iteration over the active controllers and delete them all (sometimes
under a mutex). However, a controller can be created concurrently with
module unload which can lead to leakage of resources (most important char
device node leakage) in case the controller creation occured after the
unload delete and drain sequence. To protect against this, we take a
module reference to guarantee that the nvme transport driver is not
unloaded while creating a controller.
Signed-off-by: Roy Shterman <roys@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are two put references in the failure case of initial
create_association. The first put actually frees the controller, thus the
second put references freed memory.
Remove the unnecessary 2nd put.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
So far harmless, but it's confusing and a bug waiting to happen if the
shifts grow larger than 4.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In case the queue is not LIVE (fully functional and connected at the nvmf
level), we cannot allow any commands other than connect to pass through.
Add a new queue state flag NVME_FC_Q_LIVE which is set after nvmf connect
and cleared in queue teardown.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
The driver can handle tracking only one AEN request, so this patch
removes handling for multiple ones.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This was being saved in a structure, but never used anywhere. The queue
size is obtained through other means, so there's no reason to duplicate
this without a user for it.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All the transports were unnecessarilly duplicating the AEN request
accounting. This patch defines everything in one place.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the lldd api, a lldd may unregister a remoteport (loss of connectivity
or driver unload) or localport (driver unload). The lldd must wait for the
remoteport_delete or localport_delete before completing its actions post
the unregister. The xxx_deletes currently occur only when the xxxport
structure is fully freed after all references are removed. Thus the lldd
may be held hostage until an app or in-kernel entity that has a namespace
open finally closes so the namespace can be removed, the controller
removed, thus the transport objects, thus the lldd.
This patch decouples the transport and os-facing objects from the lldd
and the remoteport and localport. There is a point in all deletions
where the transport will no longer interact with the lldd on behalf of
a controller. That point centers around the association established
with the target/subsystem. It will access the lldd whenever it attempts
to create an association and while the association is active. New
associations may only be created if the remoteport is live (thus the
localport is live). It will not access the lldd after deleting the
association.
Therefore, the patch tracks the count of active controllers - those with
associations being created or that are active - on a remoteport. It also
tracks the number of remoteports that have active controllers, on a
a localport. When a remoteport is unregistered, as soon as there are no
active controllers, the lldd's remoteport_delete may be called and the
lldd may continue. Similarly, when a localport is unregistered, as soon
as there are no remoteports with active controllers, the localport_delete
callback may be made. This significantly speeds up unregistration with
the lldd.
The transport objects continue in suspended status with reconnect timers
running, and upon expiration, normal ref-counting will occur and the
objects will be freed. The transport object may still be held hostage
by the application/kernel module, but that is acceptable.
With this change, the lldd may be fully unloaded and reloaded, and
if registrations occur prior to the timeouts, the nvme controller and
namespaces will resume normally as if a link bounce.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The localport resume was not updating the lldd ops structure. If the
lldd is unloaded and reloaded, the ops pointers will differ.
Additionally, as there are device references taken by the localport,
ensure that resume only resumes if the device matches as well.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a remoteport is unregistered (connectivity lost), the following
actions are taken:
- the remoteport is marked DELETED
- the time when dev_loss_tmo would expire is set in the remoteport
- all controllers on the remoteport are reset.
After a controller resets, it will stall in a RECONNECTING state waiting
for one of the following:
- the controller will continue to attempt reconnect per max_retries and
reconnect_delay. As no remoteport connectivity, the reconnect attempt
will immediately fail. If max reconnects has not been reached, a new
reconnect_delay timer will be schedule. If the current time plus
another reconnect_delay exceeds when dev_loss_tmo expires on the remote
port, then the reconnect_delay will be shortend to schedule no later
than when dev_loss_tmo expires. If max reconnect attempts are reached
(e.g. ctrl_loss_tmo reached) or dev_loss_tmo ix exceeded without
connectivity, the controller is deleted.
- the remoteport is re-registered prior to dev_loss_tmo expiring.
The resume of the remoteport will immediately attempt to reconnect
each of its suspended controllers.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
[hch: updated to use nvme_delete_ctrl]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Check remoteport connectivity before initiating reconnects
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a dev_loss_tmo value, paralleling the SCSI FC transport, for device
connectivity loss.
The transport initializes the value in the nvme_fc_register_remoteport()
call. If the value is not set, a default of 60s is set.
Add a new routine to the api, nvme_fc_set_remoteport_devloss() routine,
which allows the lldd to dynamically update the value on an existing
remoteport.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Clean up some of the controller state checks and add the
RESETTING->RECONNECTING state transition.
Specifically:
- the movement of the RESETTING state change and schedule of reset_work
to core doesn't work wiht nvme_fc_error_recovery setting state to
RECONNECTING before attempting to reset. Remove the state change as
the reset request does it.
- In the rare cases where an error occurs right as we're transitioning
to LIVE, defer the controller start actions.
- In error handling on teardown of associations while performing initial
controller creation - avoid quiesce calls on the admin_q. They are
unneeded.
- Add the RESETTING->RECONNECTING transition in the reset handler.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Prevent racing controller reset and delete flows. reset_work must not
ever self-requeue so flushing it suffices.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
No change in behavior except that the FC code cancels two work items a
little later now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move the ->delete_work and the associated helpers to common code instead
of duplicating them in every driver. This also adds the missing reference
get/put for the loop driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
No need to have two functions doing the same thing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There's no need to wait for the full nvme_wq, which is now shared,
to flush. flush only the delete_work item.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sgi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The define is an arbitrary limit to the io size on the initiator,
capping the io to 1MB-4KB.
Remove the define from the transport. I/O size will solely be limited
by the LLDD sg limits.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Adds support for the duplicate_connect option. When set to true,
checks whether there's an existing controller via the same host port
and target port for the same host (hostnqn, hostid) to the same
subsystem. Fails the connection request if an existing controller.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of allocating a separate struct device for the character device
handle embedd it into struct nvme_ctrl and use it for the main controller
refcounting. This removes double refcounting and gets us an automatic
reference for the character device operations. We keep ctrl->device as a
pointer for now to avoid chaning printks all over, but in the future we
could look into message printing helpers that take a controller structure
similar to what other subsystems do.
Note the delete_ctrl operation always already has a reference (either
through sysfs due this change, or because every open file on the
/dev/nvme-fabrics node has a refernece) when it is entered now, so we
don't need to do the unless_zero variant there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
The transport io timeout behavior wasn't quite correct. It ignored
that the io error handler is supposed to be synchronous so it possibly
allowed the blk request to be restarted while the io associated was
still aborting. Timeouts on reserved commands, those used for
association create, were never timing out thus they hung out forever.
To correct:
If an io is times out while a remoteport is not connected, just
restart the io timer. The lack of connectivity will simultaneously
be resetting the controller, so the reset path will abort and terminate
the io.
If an io is times out while it was marked for transport abort, just
reset the io timer. The abort process is underway and will complete
the io.
Otherwise, if an io times out, abort the io. If the abort was
unsuccessful (unlikely) give up and return not handled.
If the abort was successful, as the abort process is underway it will
terminate the io, so rather than synchronously waiting, just restart
the io timer.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The io completion handling for i/o's that are failing due to
to a transport error or association termination had issues, causing
io failures (DNR set so retries didn't kick in) or long stalls.
Change the io completion handler for the following items:
When an io has been completed due to a transport abort (based on an
exchange error) or when marked as aborted as part of an association
termination (FCOP_FLAGS_TERMIO), set the NVME completion status to
NVME_SC_ABORTED. By default, do not set DNR on the status so that a
retry can be attempted after association recreate.
In cases where an io is failed (non-successful nvme status including
aborted), if the controller is being deleted (blk_queue_dying) or
the io was part of the ios used for association creation (ctrl state
is NEW or RECONNECTING), then additionally set the DNR bit so the io
will not be retried. If the failed io was part of association creation,
the failure will tear down the partially completioned association and
typically restart a new reconnect attempt (another create association
later).
Rearranged code flow to remove a largely unneeded local variable.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since commit b86dd81
"block: get rid of blk-mq default scheduler choice Kconfig entries",
when setting nr_hw_queues to 1 the admin tag set uses mq-deadline scheduler.
This flag is useful for admin queues that aren't used for normal IO.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, if a frame is lost of command fails as part of initial
association create for a new controller, the new controller connection
request will immediately fail.
Add in an immediate 3 retry loop before giving up.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move blk_mq_reinit_tagset from blk-mq to nvme core
as the only user of it. Current transports that use
it (rdma, fc) simply implement .reinit_request op.
This patch does not change any functionality.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
move nvme_fc_rport_get/put and rport free to higher in the file to
avoid adding prototypes to resolve references in upcoming code additions
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Added a new fc class and a device node for udev events under it. I
expect the fc class will eventually be the location where the FC SCSI and
FC NVME merge in the future. Therefore names are kept somewhat generic.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
To support auto-connecting to FC-NVME devices upon their dynamic
appearance, add a uevent that can kick off connection scripts.
uevent is posted against the fc_udev device.
patch set tested with the following rule to kick an nvme-cli connect-all
for the FC initiator and FC target ports. This is just an example for
testing and not intended for real life use.
ACTION=="change", SUBSYSTEM=="fc", ENV{FC_EVENT}=="nvmediscovery", \
ENV{NVMEFC_HOST_TRADDR}=="*", ENV{NVMEFC_TRADDR}=="*", \
RUN+="/bin/sh -c '/usr/local/sbin/nvme connect-all --transport=fc --host-traddr=$env{NVMEFC_HOST_TRADDR} --traddr=$env{NVMEFC_TRADDR} >> /tmp/nvme_fc.log'"
I will post proposed udev/systemd scripts for possible kernel support.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
