This controller disallows to change the PIPE until reading/writing
a packet finishes. However. the previous code is not enough to hold
the lock in some functions. So, this patch fixes it.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver is possible to cause
deadlock by double-spinclocked in renesas_usb3_stop_controller().
So, this patch removes spinlock API calling in renesas_usb3_stop().
(In other words, the previous code had a redundant lock.)
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver is possible to access
the registers before pm_runtime_get_sync() if a gadget driver is
installed first. After that, oops happens on R-Car Gen3 environment.
To avoid it, this patch changes the pm_runtime call timing from
probe/remove to udc_start/udc_stop.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
f_mass_storage has a memorry barrier issue with the sleep and wake
functions that can cause a deadlock. This results in intermittent hangs
during MSC file transfer. The host will reset the device after receiving
no response to resume the transfer. This issue is seen when dwc3 is
processing 2 transfer-in-progress events at the same time, invoking
completion handlers for CSW and CBW. Also this issue occurs depending on
the system timing and latency.
To increase the chance to hit this issue, you can force dwc3 driver to
wait and process those 2 events at once by adding a small delay (~100us)
in dwc3_check_event_buf() whenever the request is for CSW and read the
event count again. Avoid debugging with printk and ftrace as extra
delays and memory barrier will mask this issue.
Scenario which can lead to failure:
-----------------------------------
1) The main thread sleeps and waits for the next command in
get_next_command().
2) bulk_in_complete() wakes up main thread for CSW.
3) bulk_out_complete() tries to wake up the running main thread for CBW.
4) thread_wakeup_needed is not loaded with correct value in
sleep_thread().
5) Main thread goes to sleep again.
The pattern is shown below. Note the 2 critical variables.
* common->thread_wakeup_needed
* bh->state
CPU 0 (sleep_thread) CPU 1 (wakeup_thread)
============================== ===============================
bh->state = BH_STATE_FULL;
smp_wmb();
thread_wakeup_needed = 0; thread_wakeup_needed = 1;
smp_rmb();
if (bh->state != BH_STATE_FULL)
sleep again ...
As pointed out by Alan Stern, this is an R-pattern issue. The issue can
be seen when there are two wakeups in quick succession. The
thread_wakeup_needed can be overwritten in sleep_thread, and the read of
the bh->state maybe reordered before the write to thread_wakeup_needed.
This patch applies full memory barrier smp_mb() in both sleep_thread()
and wakeup_thread() to ensure the order which the thread_wakeup_needed
and bh->state are written and loaded.
However, a better solution in the future would be to use wait_queue
method that takes care of managing memory barrier between waker and
waiter.
Cc: <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commit allows a gadget that does not support SuperSpeed to indicate
that it supports LPM. It does this by setting the 'lpm_capable' flag in
the gadget structure.
If a gadget sets this, the composite gadget framework will set the
bcdUSB to 0x0201 to indicate that this supports BOS descriptors, and
also return a USB 2.0 Extension descriptor as part of the BOS descriptor
set.
See USB 2.0 LPM ECN Section 3.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Don't send the SuperSpeed USB Device Capability descriptor if
the gadget is not capable of SuperSpeed.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There were individual waitqueues for each epfile but eps_enable
would iterate through all of them, resulting in essentially the
same wakeup time.
The waitqueue represents the function being enabled, so a central
waitqueue in ffs_data makes more sense and is less redundant.
Also use wake_up_interruptible to reflect use of
wait_event_interruptible.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This allows users to make an ioctl call as the first action on a
connection. Ex, some functions might want to get endpoint size
before making any i/os.
Previously, calling ioctls before read/write would depending on the
timing of endpoints being enabled.
ESHUTDOWN is now a possible return value and ENODEV is not, so change
docs accordingly.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead, we can require caller to pass a buffer for the function to
use. This cleans things quite a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of going for a 512 byte buffer and using snprintf(), let's
rely on helps __string() and __assign_str() where possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of printing out enqueue and dequeue pointer value as a header
to the output, let's mark the TRBs in question with 'E' and 'D'. The
output looks slightly easier to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
%p will leak kernel pointers, so let's not expose the information on
dmesg and instead use %pK. %pK will only show the actual addresses if
explicitly enabled under /proc/sys/kernel/kptr_restrict.
Cc: <stable@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some local constants don't change from call to call and are good
candidates to become static. This will prevent copying of these
constants to stack during runtime.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently VBUS is turned off while a usb device is detached, and turned
on again by the polling routine. This short period VBUS loss prevents
usb modem to switch mode.
VBUS should be constantly on for host-only mode, so this changes the
driver to not turn off VBUS for host-only mode.
Fixes: 2f3fd2c5bd ("usb: musb: Prepare dsps glue layer for PM runtime support")
Cc: stable@vger.kernel.org #v4.11
Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The combo of list_empty() and list_first_entry() can be replaced with
list_first_entry_or_null().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Aspeed 2400/2500 families have a variant of UHCI which requires
some quirks to the driver to work:
- The register offsets are different. We add a remapping helper.
- All accesses have to be done via 32-bit loads and stores. We
force all accessors to use readl/writel. This is of no consequence
for reads as we never read "in the middle" of a register. For writes
it also works fine as the registers only actually implement the bits
we try to write (16-bit for the registers accessed with writew and
8-bit for the register accessed with writeb), so always using a
32-bit write will have no negative effect. We never do partial writes.
- The resume detect interrupt is broken
- The number of ports is (optionally) provided via the device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
--
v2. Remove the bulk of the #ifdef's
drivers/usb/host/Kconfig | 6 ++++-
drivers/usb/host/uhci-hcd.c | 17 +++++++++++---
drivers/usb/host/uhci-hcd.h | 51 ++++++++++++++++++++++++++++++++++++++++
drivers/usb/host/uhci-platform.c | 22 ++++++++++++++++-
4 files changed, 91 insertions(+), 5 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJZI4ULAAoJEEhZKYFQ1nG7zS0H9Rq3yIJaLMPI9y4bBatTvP1L
pmKu0/wpCUfzWCOJ4RFp1X0Up2kqe6z7U/+YQLNyRT/1/ssiNuT7BIl+Cy+WtAD5
IN1ChG6769eshd+FT4gpg5TobXIP7daYFHehbe/9UQofyiMukyPaV3lSUR1XO4FB
Z66pGfnij0O+pPkFuQ8ARE/VrHo2vlGC4coOtbUVG8eYMgzjPblPRWFTGVf0LcFq
7p26Ggp3WzsDqP9mwBZUjCFm5TA/9gF14KPywOToarY2Fz2FHTaK82L1r0QnE+61
Fla9TejbW553zuA6SRWOJL8M10TFZ/g/6/FRuVKbfPGHmRzL26v8iwFDhHmKXA==
=WS1v
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Some small bugs
ci_role BUGs when the role is >= CI_ROLE_END.
This is the case while the role is changing.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
ci_role BUGs when the role is >= CI_ROLE_END.
Cc: stable@vger.kernel.org #v3.10+
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Here's a fix for a long-standing issue in the ftdi_sio driver that
prevented unprivileged users from updating the low-latency flag,
something which became apparent after a recent change that restored the
older setting of not using low-latency mode by default.
A run of sparse revealed a couple of endianness issues that are now
fixed, and addressed is also a user-triggerable division-by-zero in
io_ti when debugging is enabled.
Finally there are some new device ids, including a simplification of how
we deal with a couple of older Olimex JTAG adapters.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=psyq
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.12-rc2
Here's a fix for a long-standing issue in the ftdi_sio driver that
prevented unprivileged users from updating the low-latency flag,
something which became apparent after a recent change that restored the
older setting of not using low-latency mode by default.
A run of sparse revealed a couple of endianness issues that are now
fixed, and addressed is also a user-triggerable division-by-zero in
io_ti when debugging is enabled.
Finally there are some new device ids, including a simplification of how
we deal with a couple of older Olimex JTAG adapters.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
In the ene_usb6250 sub-driver for usb-storage, the INQUIRY data
returned by the driver indicates that the device has removable media.
While this is technically correct (memory cards can be removed from
the reader), it is not useful because the device automatically
disconnects itself from the USB bus when no media is present.
In addition, the driver does not support the PREVENT-ALLOW MEDIUM
REMOVAL and START STOP UNIT commands, and this can cause
user-interface frameworks to get confused when the user asks for the
card to be removed or ejected.
This patch fixes the problem by changing the INQUIRY data to specify
non-removable media; in practice this value works much better.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the sd_scsi_inquiry()
and ms_scsi_inquiry() subroutines (one meant for use with SD memory
cards and the other for use with MS memory cards) are exact
duplicates. This patch removes the duplication by creating a single
do_scsi_inquiry() command and using it instead of the other two.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, there is no support for
the REQUEST SENSE command. This command is issued whenever a failure
occurs, and without it the driver has no way to tell the SCSI core
what the reason for the failure was.
This patch adds a do_scsi_request_sense() routine to the driver. The
new routine reports the error code stored by the previous command.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the SCSI residue is not
reported correctly. The residue is initialized to 0, but this value
is overwritten whenever the driver sends firmware to the card reader
before performing the current command. As a result, a valid READ or
WRITE operation appears to have failed, causing the SCSI core to retry
the command multiple times and eventually fail.
This patch fixes the problem by resetting the SCSI residue to 0 after
sending firmware to the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ene_usb6250 sub-driver for usb-storage, the ene_transport()
routine is supposed to initialize the driver before executing the
current command, if the initialization has not already been performed.
However, a bug in the routine causes it to skip the command after
doing the initialization. Also, the routine does not return an
appropriate error code if either the initialization or the command
fails.
As a result of the first bug, the first command (a SCSI INQUIRY) is
not carried out. The results can be seen in the system log, in the
form of a warning message and empty or garbage INQUIRY data:
Apr 18 22:40:08 notebook2 kernel: scsi host6: scsi scan: INQUIRY result too short (5), using 36
Apr 18 22:40:08 notebook2 kernel: scsi 6:0:0:0: Direct-Access PQ: 0 ANSI: 0
This patch fixes both errors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have one register for each EP to set the maximum packet size for both
TX and RX.
If for example an RX programming would happen before the previous TX
transfer finishes we would reset the TX packet side.
To fix this issue, only modify the TX or RX part of the register.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe
lock order error") caused a regression where musb keeps trying to
enable host mode with no cable connected. This seems to be caused
by the fact that now phy is enabled earlier, and we are wrongly
trying to force USB host mode on an OTG port. The errors we are
getting are "trying to suspend as a_idle while active".
For ports configured as OTG, we should not need to do anything
to try to force USB host mode on it's OTG port. Trying to force host
mode in this case just seems to completely confuse the musb state
machine.
Let's fix the issue by making musb_host_setup() attempt to force the
mode only if port_mode is configured for host mode.
Fixes: d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe lock order error")
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the xhci-plat driver
ignores it and always returns -ENODEV. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
CC: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4.11 TRB completion codes were renamed to match spec.
Completion codes for command ring stopped and endpoint stopped
were mixed, leading to failures while handling a stopped command ring.
Use the correct completion code for command ring stopped events.
Fixes: 0b7c105a04 ("usb: host: xhci: rename completion codes to match spec")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to restrict allocations to the first 16MB ISA DMA
addresses.
It is causing problems in a virtualization setup with enabled IOMMU
(x86_64). The result is that USB is not working in the VM.
CC: <stable@vger.kernel.org>
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With threaded interrupts, bottom-half handlers are called with
interrupts enabled. Therefore they can't safely use spin_lock(); they
have to use spin_lock_irqsave(). Lockdep warns about a violation
occurring in xhci_irq():
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
4.11.0-rc8-dbg+ #1 Not tainted
---------------------------------------------------------
swapper/7/0 just changed the state of lock:
(&(&ehci->lock)->rlock){-.-...}, at: [<ffffffffa0130a69>]
ehci_hrtimer_func+0x29/0xc0 [ehci_hcd]
but this lock took another, HARDIRQ-unsafe lock in the past:
(hcd_urb_list_lock){+.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(hcd_urb_list_lock);
local_irq_disable();
lock(&(&ehci->lock)->rlock);
lock(hcd_urb_list_lock);
<Interrupt>
lock(&(&ehci->lock)->rlock);
*** DEADLOCK ***
no locks held by swapper/7/0.
the shortest dependencies between 2nd lock and 1st lock:
-> (hcd_urb_list_lock){+.....} ops: 252 {
HARDIRQ-ON-W at:
__lock_acquire+0x602/0x1280
lock_acquire+0xd5/0x1c0
_raw_spin_lock+0x2f/0x40
usb_hcd_unlink_urb_from_ep+0x1b/0x60 [usbcore]
xhci_giveback_urb_in_irq.isra.45+0x70/0x1b0 [xhci_hcd]
finish_td.constprop.60+0x1d8/0x2e0 [xhci_hcd]
xhci_irq+0xdd6/0x1fa0 [xhci_hcd]
usb_hcd_irq+0x26/0x40 [usbcore]
irq_forced_thread_fn+0x2f/0x70
irq_thread+0x149/0x1d0
kthread+0x113/0x150
ret_from_fork+0x2e/0x40
This patch fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Bart Van Assche <bart.vanassche@sandisk.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI spec Figure 30: Interrupt Throttle Flow Diagram
If PCI Message Signaled Interrupts (MSI or MSI-X) are enabled,
then the assertion of the Interrupt Pending (IP) flag in Figure 30
generates a PCI Dword write. The IP flag is automatically cleared
by the completion of the PCI write.
the MSI enabled HCs don't need to clear interrupt pending bit, but
hcd->irq = 0 doesn't equal to MSI enabled HCD. At some Dual-role
controller software designs, it sets hcd->irq as 0 to avoid HCD
requesting interrupt, and they want to decide when to call usb_hcd_irq
by software.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to xHCI ch4.20 Scratchpad Buffers, the Scratchpad
Buffer needs to be zeroed.
...
The following operations take place to allocate
Scratchpad Buffers to the xHC:
...
b. Software clears the Scratchpad Buffer to '0'
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Denverton microserver is Atom based and need the PME and CAS quirks
as well.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't access any members of a URB after giving it back.
URB might be freed by then already.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike i.MX53, i.MX51's USBOH3 register file does not implemenent
registers past offset 0x018, which includes
MX53_USB_CLKONOFF_CTRL_OFFSET and trying to access that register on
said platform results in external abort.
Fix it by enabling CLKONOFF accessing codepath only for i.MX53.
Cc: stable <stable@vger.kernel.org>
Fixes 3be3251db0 ("usb: chipidea: imx: Disable internal 60Mhz
clock with ULPI PHY")
Cc: cphealy@gmail.com
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If ci_hdrc_host_init() or ci_hdrc_gadget_init() returns error and the
error != -ENXIO, as Peter pointed out, "it stands for initialization
for host or gadget has failed", so we'd better return failure rather
continue.
And before destroying the otg, i.e ci_hdrc_otg_destroy(ci), we should
also check ci->roles[CI_ROLE_GADGET].
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use new USB device IDs for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
"ep->udc->lock" and "udc->lock" are the same thing. It confuses Smatch
if we don't use the same name consistently.
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usb phy core has added common code to register or unregister
extcon device, then phy-msm-usb driver does not need its own
code to register/unregister extcon device, then remove them.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usb phy core has added common code to register or unregister
extcon device, then phy-qcom-8x16-usb driver does not need its own
code to register/unregister extcon device, then remove them.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Usually usb phy need register one extcon device to get the connection
notifications. It will remove some duplicate code if the extcon device
is registered using common code instead of each phy driver having its
own related extcon APIs. So we add one pointer of extcon device into
usb phy structure, and some other helper functions to register extcon.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB gadget documentation is not at DocBook anymore.
The main file was converted to ReST, and stored at
Documentation/driver-api/usb/gadget.rst, but there are
still several plain text files related to gadget under
Documentation/usb.
So, be generic and just mention documentation
without specifying where it is.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calculate wMaxPacketSize before endpoint matching the
descriptor is found.
This allows audio gadget to be used with controllers
which have a shortage or unavailability of endpoints
that can handle max packet size of 1023 (FS) or 1024
(HS).
With this audio gadget can be used on TI's OMAP-L138 SoC
which has a MUSB HS controller with endpoints having max
packet size much less than 1023 or 1024. See mode_2_cfg in
drivers/usb/musb/musb_core.c
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some functions might want to have very, very long request queues. We
can't make any assumptions about how many requests we *are* able to
map, so instead of mapping requests early, let's map them late. This
way, functions can queue as many requests as they'd like but we won't
take DMA resources until they are needed.
Also, we can now stop processing requests when we run out of DMA
resources but still keep requests in the queue for late processing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary null check. udev->tt cannot ever be NULL when this
section of code runs.
Addresses-Coverity-ID: 100828
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some situations, e.g. when registering alternate modes for local typec
ports, it may be handy to use constant mode descriptors. Allow this by
changing the mode descriptor arguments of typec_port_register_altmode()
et.al. to using const pointers.
Signed-off-by: Mats Karrman <mats.dev.list@gmail.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check that req->buf is a valid DMA capable address, produce a warning
and return an error if it's either coming from vmalloc space or is an on
stack buffer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update usb_hcd_map_urb_for_dma() to check for an URB's setup_packet and
transfer_buffer sanity. We first check that urb->setup_packet is neither
coming from vmalloc space nor is an on stack buffer, and if that's the
case, produce a warning and return an error. For urb->transfer_buffer
there is an existing is_vmalloc_addr() check so we just supplement that
with an object_is_on_stack() check, produce a warning if that is the case
and also return an error.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need a big fat warning with stack dump at all. Running out of
TRBs is a normal condition and we will have more TRBs available as
soon as some transfers complete.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use the new define for the maximum number of SuperSpeed ports instead of
a constant when allocating xHCI root hubs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add define for the maximum number of ports on a SuperSpeed hub as per
USB 3.1 spec Table 10-5, and use it when verifying the retrieved hub
descriptor.
This specifically avoids benign attempts to update the DeviceRemovable
mask for non-existing ports (should we get that far).
Fixes: dbe79bbe9d ("USB 3.0 Hub Changes")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing sanity check on the non-SuperSpeed hub-descriptor length in
order to avoid parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes (or a compound-device debug
statement).
Note that we only make sure that the DeviceRemovable field is always
present (and specifically ignore the unused PortPwrCtrlMask field) in
order to continue support any hubs with non-compliant descriptors. As a
further safeguard, the descriptor buffer is also cleared.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeed hub descriptor does not have any variable-length fields so
bail out when reading a short descriptor.
This avoids parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes.
Fixes: dbe79bbe9d ("USB 3.0 Hub Changes")
Cc: stable <stable@vger.kernel.org> # 2.6.39
Cc: John Youn <John.Youn@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix up the root-hub descriptor to accommodate the variable-length
DeviceRemovable and PortPwrCtrlMask fields, while marking all ports as
removable (and leaving the reserved bit zero unset).
Also add a build-time constraint on VHCI_HC_PORTS which must never be
greater than USB_MAXCHILDREN (but this was only enforced through a
KConfig constant).
This specifically fixes the descriptor layout whenever VHCI_HC_PORTS is
greater than seven (default is 8).
Fixes: 04679b3489 ("Staging: USB/IP: add client driver")
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flag the first and only port as removable while also leaving the
remaining bits (including the reserved bit zero) unset in accordance
with the specifications:
"Within a byte, if no port exists for a given location, the bit
field representing the port characteristics shall be 0."
Also add a comment marking the legacy PortPwrCtrlMask field.
Fixes: 1cd8fd2887 ("usb: gadget: dummy_hcd: add SuperSpeed support")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document that the new companion-device lookup helper takes a reference
to the companion device which needs to be dropped after use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure do drop the reference taken to the companion device during
resume.
Fixes: d4d75128b8 ("usb: host: ehci-platform: fix usb 1.1 device is not connected in system resume")
Cc: stable <stable@vger.kernel.org> # 4.11
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If multiple endpoints on a single device have pending IN URBs and one
endpoint times out due to NAKs (perfectly legal), select a different
endpoint URB to try.
The existing code only checked to see another device address has pending
URBs and ignores other IN endpoints on the current device address. This
leads to endpoints never getting serviced if one endpoint is using NAK as
a flow control method.
Fixes: 5d3043586d ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timeout for BULK packets was 300ms which is a long time if other
endpoints or devices are waiting for their turn. Changing it to 50ms
greatly increased the overall performance for multi-endpoint devices.
Fixes: 5d3043586d ("usb: r8a66597-hcd: host controller driver for R8A6659")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop erroneous le16_to_cpu when returning the USB device speed which is
already in host byte order.
Found using sparse:
warning: cast to restricted __le16
Fixes: 946b960d13 ("USB: add driver for iowarrior devices.")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing endianness conversion when applying the Alea timeout quirk.
Found using sparse:
warning: restricted __le16 degrades to integer
Fixes: e4a886e811 ("hwrng: chaoskey - Fix URB warning due to timeout on Alea")
Cc: stable <stable@vger.kernel.org> # 4.8
Cc: Bob Ham <bob.ham@collabora.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d705ff3818 (tty: vt, cleanup and document con_scroll), in
the coccinelle output, we can see:
drivers/usb/misc/sisusbvga/sisusb_con.c:852:8-9: WARNING: return of 0/1 in function 'sisusbcon_scroll_area' with return type bool
Return true instead of 1 in the function returning bool which was
intended to do in d705ff3818 but omitted.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: d705ff3818 (tty: vt, cleanup and document con_scroll)
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_version_reply is not freed if function returns with success.
Fixes: 942a48730f ("usb: misc: legousbtower: Fix buffers on stack")
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format specifier %p can leak kernel addresses while not valuing the
kptr_restrict system settings. When kptr_restrict is set to (1), kernel
pointers printed using the %pK format specifier will be replaced with
Zeros. Debugging Note : &pK prints only Zeros as address. If you need
actual address information, write 0 to kptr_restrict.
echo 0 > /proc/sys/kernel/kptr_restrict
[Found by poking around in a random vendor kernel tree, it would be nice
if someone would actually send these types of patches upstream - gkh]
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ene_usb6250 sub-driver in usb-storage does USB I/O to buffers on
the stack, which doesn't work with vmapped stacks. This patch fixes
the problem by allocating a separate 512-byte buffer at probe time and
using it for all of the offending I/O operations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for recognition of ARM-USB-TINY(H) devices which
are almost identical to ARM-USB-OCD(H) but lacking separate barrel jack
and serial console.
By suggestion from Johan Hovold it is possible to replace
ftdi_jtag_quirk with a bit more generic construction. Since all
Olimex-ARM debuggers has exactly two ports, we could safely always use
only second port within the debugger family.
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Function devm_clk_get() returns an ERR_PTR when it fails. However, in
function kdwc3_probe(), its return value is not checked, which may
result in a bad memory access bug. This patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Companion descriptor is only used for SuperSpeed endpoints,
if the endpoints are HighSpeed or FullSpeed, the Companion
descriptor will not allocated, so we can only access it if
gadget is SuperSpeed.
I can reproduce this issue on Rockchip platform rk3368 SoC
which supports USB 2.0, and use functionfs for ADB. Kernel
build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report
the following BUG:
==================================================================
BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509
Read of size 1 by task swapper/0/0
============================================================================
BUG kmalloc-256 (Not tainted): kasan: bad access detected
----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1
alloc_debug_processing+0x128/0x17c
___slab_alloc.constprop.58+0x50c/0x610
__slab_alloc.isra.55.constprop.57+0x24/0x34
__kmalloc+0xe0/0x250
ffs_func_bind+0x52c/0x99c
usb_add_function+0xd8/0x1d4
configfs_composite_bind+0x48c/0x570
udc_bind_to_driver+0x6c/0x170
usb_udc_attach_driver+0xa4/0xd0
gadget_dev_desc_UDC_store+0xcc/0x118
configfs_write_file+0x1a0/0x1f8
__vfs_write+0x64/0x174
vfs_write+0xe4/0x200
SyS_write+0x68/0xc8
el0_svc_naked+0x24/0x28
INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247
...
Call trace:
[<ffffff900808aab4>] dump_backtrace+0x0/0x230
[<ffffff900808acf8>] show_stack+0x14/0x1c
[<ffffff90084ad420>] dump_stack+0xa0/0xc8
[<ffffff90082157cc>] print_trailer+0x188/0x198
[<ffffff9008215948>] object_err+0x3c/0x4c
[<ffffff900821b5ac>] kasan_report+0x324/0x4dc
[<ffffff900821aa38>] __asan_load1+0x24/0x50
[<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0
[<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8
[<ffffff90089d7394>] android_setup+0x124/0x1a0
[<ffffff90089acd18>] _setup+0x54/0x74
[<ffffff90089b6b98>] handle_ep0+0x3288/0x4390
[<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4
[<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298
[<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20
[<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac
[<ffffff9008116610>] handle_irq_event+0x60/0xa0
[<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4
[<ffffff9008115568>] generic_handle_irq+0x30/0x40
[<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc
[<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4
...
Memory state around the buggy address:
ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc
>ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check for bad pointer that may result because of kthread_create failure.
This check is needed since the gserial setup callback function
(gs_console_setup()) is only freeing the info->con_buf in case of
kthread_create failure which will result into bad info->console_thread
pointer.
Without checking info->console_thread pointer validity in the
gserial_console_exit() function, before calling kthread_stop(), the
rmmod will generate Kernel Oops.
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_mirea@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc3 driver can overwite its previous events if its top-half IRQ
handler (TH) gets invoked again before processing the events in the
cache. We see this as a hang in the file transfer and the host will
attempt to reset the device. TH gets the event count and deasserts the
interrupt line by writing DWC3_GEVNTSIZ_INTMASK to DWC3_GEVNTSIZ. If
there's a new event coming between reading the event count and interrupt
deassertion, dwc3 will lose previous pending events. More generally, we
will see 0 event count, which should not affect anything.
This shouldn't be possible in the current dwc3 implementation. However,
through testing and reading the PCIe trace, the TH occasionally still
gets invoked one more time after HW interrupt deassertion. (With PCIe
legacy interrupts, TH is called repeatedly as long as the interrupt line
is asserted). We suspect that there is a small detection delay in the
SW.
To avoid this issue, Check DWC3_EVENT_PENDING flag to determine if the
events are processed in the bottom-half IRQ handler. If not, return
IRQ_HANDLED and don't process new event.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
caused a small change in the way ISO transfer is handled in the case
when XferInProgress event happens on Isoc EP with an active transfer.
This caused a performance degradation of 50%. e.g. using g_webcam on DUT
and luvcview on host the video frame rate dropped from 16fps to 8fps
@high-speed.
Make the ISO transfer handling equivalent to that prior to that commit
to get back the original ISO performance numbers.
Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel Cannonlake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new IDs to the supported devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch reworks the way f_mass_storage.c handles memory barriers
and synchronization:
The driver now uses a wait_queue instead of doing its own
task-state manipulations (even though only one task will ever
use the wait_queue).
The thread_wakeup_needed variable is removed. It was only a
source of trouble; although it was what the driver tested to
see whether it should wake up, what we really wanted to see
was whether a USB transfer had completed.
All the explicit memory barriers scattered throughout the
driver are replaced by a few calls to smp_load_acquire() and
smp_store_release().
The inreq_busy and outreq_busy fields are removed. In their
place, the driver keeps track of the current I/O direction by
splitting BUF_STATE_BUSY into two states: BUF_STATE_SENDING
and BUF_STATE_RECEIVING.
The buffer states are no longer protected by a lock. Mutual
exclusion isn't needed; the state is changed only by the
driver's main thread when it owns the buffer, and only by the
request completion routine when the gadget core owns the buffer.
The do_write() and throw_away_data() routines were reorganized
to make efficient use of the new sleeping mechanism. This
resulted in the removal of one indentation level in those
routines, making the patch appear to be more more complicated
than it really is.
In a few places, the driver allowed itself to be frozen although
it really shouldn't have (in the middle of executing a SCSI
command). Those places have been fixed.
The logic in the exception handler for aborting transfers and
waiting for them to stop has been simplified.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch makes several adjustments to the way f_mass_storage.c
handles its internal state and asynchronous notifications (AKA
exceptions):
A number of states weren't being used for anything.
They are removed.
The FSG_STATE_IDLE state was renamed to FSG_STATE_NORMAL,
because it now applies whenever the gadget is operating
normally, not just when the gadget is idle.
The FSG_STATE_RESET state was renamed to
FSG_STATE_PROTOCOL_RESET, indicating that it represents a
Bulk-Only Transport protocol reset and not a general USB
reset.
When a signal arrives, it's silly for the signal handler to
send itself another signal! Now it takes care of everything
inline.
Along with an assortment of other minor changes in the same category.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix a division-by-zero in set_termios when debugging is enabled and a
high-enough speed has been requested so that the divisor value becomes
zero.
Instead of just fixing the offending debug statement, cap the baud rate
at the base as a zero divisor value also appears to crash the firmware.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.12
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop erroneous cpu_to_le32 when setting the baud rate, something which
corrupted the divisor on big-endian hosts.
Found using sparse:
warning: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] val
got restricted __le32 [usertype] <noident>
Fixes: af2ac1a091 ("USB: serial mct_usb232: move DMA buffers to heap")
Cc: stable <stable@vger.kernel.org> # 2.6.34
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing endianness conversion when printing the supported baud
rates.
Found using sparse:
warning: restricted __le16 degrades to integer
Fixes: e0d795e4f3 ("usb: irda: cleanup on ir-usb module")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY
flag") enables unprivileged users to set the FTDI latency timer,
but there was a logic flaw that skipped sending the corresponding
USB control message to the device.
Specifically, the device latency timer would not be updated until next
open, something which was later also inadvertently broken by commit
c19db4c9e4 ("USB: ftdi_sio: set device latency timeout at port
probe").
A recent commit c6dce26266 ("USB: serial: ftdi_sio: fix extreme
low-latency setting") disabled the low-latency mode by default so we now
need this fix to allow unprivileged users to again enable it.
Signed-off-by: Anthony Mallet <anthony.mallet@laas.fr>
[johan: amend commit message]
Fixes: 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY flag")
Fixes: c19db4c9e4 ("USB: ftdi_sio: set device latency timeout at port probe").
Cc: stable <stable@vger.kernel.org> # 2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for Telit ME910 PID 0x1100.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
- Fix sparse warnings in drivers/of/.
- Add more overlay unittests.
- Update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names.
- Add a common DT modalias function.
- Move trivial-devices.txt up and out of i2c dir.
- ARM NVIC interrupt controller binding.
- Vendor prefixes for Sensirion, Dioo, Nordic, ROHM.
- Correct some binding file locations.
-----BEGIN PGP SIGNATURE-----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=ca1M
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- fix sparse warnings in drivers/of/
- add more overlay unittests
- update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names
- add a common DT modalias function
- move trivial-devices.txt up and out of i2c dir
- ARM NVIC interrupt controller binding
- vendor prefixes for Sensirion, Dioo, Nordic, ROHM
- correct some binding file locations
* tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (24 commits)
of: fix sparse warnings in fdt, irq, reserved mem, and resolver code
of: fix sparse warning in of_pci_range_parser_one
of: fix sparse warnings in of_find_next_cache_node
of/unittest: Missing unlocks on error
of: fix uninitialized variable warning for overlay test
of: fix unittest build without CONFIG_OF_OVERLAY
of: Add unit tests for applying overlays
of: per-file dtc compiler flags
fpga: region: add missing DT documentation for config complete timeout
of: Add vendor prefix for ROHM Semiconductor
of: fix "/cpus" reference leak in of_numa_parse_cpu_nodes()
of: Add vendor prefix for Nordic Semiconductor
dt-bindings: arm,nvic: Binding for ARM NVIC interrupt controller on Cortex-M
dtc: update warning settings for new bus and node/property name checks
scripts/dtc: Update to upstream version v1.4.4-8-g756ffc4f52f6
scripts/dtc: automate getting dtc version and log in update script
of: Add function for generating a DT modalias with a newline
of: fix of_device_get_modalias returned length when truncating buffers
Documentation: devicetree: move trivial-devices out of I2C realm
dt-bindings: add vendor prefix for Dioo
..
Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to the Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why it's
coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a common
way, which will help prevent any "badly-formed" devices from causing
problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvEIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yny4gCePCXxnrQdMWE+IMXf1H1hMubLkVkAn0ZWgQkq
BspgO7ZmGb+9Fpf6YvNz
=nwAu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why
it's coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a
common way, which will help prevent any "badly-formed" devices from
causing problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
staging: typec: Fairchild FUSB302 Type-c chip driver
staging: typec: Type-C Port Controller Interface driver (tcpci)
staging: typec: USB Type-C Port Manager (tcpm)
usb: host: xhci: remove #ifdef around PM functions
usb: musb: don't mark of_dev_auxdata as initdata
usb: misc: legousbtower: Fix buffers on stack
USB: Revert "cdc-wdm: fix "out-of-sync" due to missing notifications"
usb: Make sure usb/phy/of gets built-in
USB: storage: e-mail update in drivers/usb/storage/unusual_devs.h
usb: host: xhci: print correct command ring address
usb: host: xhci: delete sp_dma_buffers for scratchpad
usb: host: xhci: using correct specification chapter reference for DCBAAP
xhci: switch to pci_alloc_irq_vectors
usb: host: xhci-plat: set resume_quirk() for R-Car controllers
usb: host: xhci-plat: add resume_quirk()
usb: host: xhci-plat: enable clk in resume timing
usb: host: plat: Enable xHCI plat runtime PM
USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit
USB: serial: constify static arrays
usb: fix some references for /proc/bus/usb
...
Core changes
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources.
I have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements
- A whole slew of drivers have their spinlocks chaned to raw spinlocks
as they provide irqchips, and thus we are progressing on realtime
compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot.
-----BEGIN PGP SIGNATURE-----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=DGPb
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.12 kernel cycle.
Core changes:
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources. I
have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers:
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements:
- A whole slew of drivers have their spinlocks chaned to raw
spinlocks as they provide irqchips, and thus we are progressing on
realtime compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot"
* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: f7188x: Add a missing break
gpio: omap: return error if requested debounce time is not possible
gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
gpio: gpio-wcove: fix GPIO IRQ status mask
gpio: DT bindings, move tca9554 from pcf857x to pca953x
gpio: move tca9554 from pcf857x to pca953x
gpio: arizona: Correct check whether the pin is an input
gpio: Add XRA1403 DTS binding documentation
dt-bindings: add exar to vendor prefixes list
gpio: gpio-wcove: fix irq pending status bit width
gpio: dwapb: use dwapb_read instead of readl_relaxed
gpio: aspeed: Add open-source and open-drain support
gpio: aspeed: Add debounce support
gpio: aspeed: dt: Add optional clocks property
gpio: aspeed: dt: Fix description alignment in bindings document
gpio: mvebu: Add limited PWM support
gpio: Use unsigned int for interrupt numbers
gpio: f7188x: Add F71889A GPIO support.
gpio: core: Decouple open drain/source flag with active low/high
gpio: arizona: Correct handling for reading input GPIOs
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
guide for user-space API documents, rather sparsely populated at the
moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of Documentation/
to fix comments elsewhere in the tree; I have acks for those where I could
get them.
-----BEGIN PGP SIGNATURE-----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=41m+
-----END PGP SIGNATURE-----
Merge tag 'docs-4.12' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"A reasonably busy cycle for documentation this time around. There is a
new guide for user-space API documents, rather sparsely populated at
the moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of
Documentation/ to fix comments elsewhere in the tree; I have acks for
those where I could get them"
* tag 'docs-4.12' of git://git.lwn.net/linux: (74 commits)
docs: Fix a couple typos
docs: Fix a spelling error in vfio-mediated-device.txt
docs: Fix a spelling error in ioctl-number.txt
MAINTAINERS: update file entry for HSI subsystem
Documentation: allow installing man pages to a user defined directory
Doc/PM: Sync with intel_powerclamp code behavior
zr364xx.rst: usb/devices is now at /sys/kernel/debug/
usb.rst: move documentation from proc_usb_info.txt to USB ReST book
convert philips.txt to ReST and add to media docs
docs-rst: usb: update old usbfs-related documentation
arm: Documentation: update a path name
docs: process/4.Coding.rst: Fix a couple of document refs
docs-rst: fix usb cross-references
usb: gadget.h: be consistent at kernel doc macros
usb: composite.h: fix two warnings when building docs
usb: get rid of some ReST doc build errors
usb.rst: get rid of some Sphinx errors
usb/URB.txt: convert to ReST and update it
usb/persist.txt: convert to ReST and add to driver-api book
usb/hotplug.txt: convert to ReST and add to driver-api book
...
Pull x86 debug updates from Ingo Molnar:
"The biggest update is the addition of USB3 debug port based
early-console.
Greg was fine with the USB changes and with the routing of these
patches:
https://www.spinics.net/lists/linux-usb/msg155093.html"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
usb/doc: Add document for USB3 debug port usage
usb/serial: Add DBC debug device support to usb_debug
x86/earlyprintk: Add support for earlyprintk via USB3 debug port
usb/early: Add driver for xhci debug capability
x86/timers: Add simple udelay calibration
The #ifdef is slightly wrong as it doesn't cover the xhci_priv_resume_quirk()
function, causing a harmless warning:
drivers/usb/host/xhci-plat.c:58:12: error: 'xhci_priv_resume_quirk' defined but not used [-Werror=unused-function]
static int xhci_priv_resume_quirk(struct usb_hcd *hcd)
A simpler way to do this correctly is to use __maybe_unused annotations
that let the compiler silently drop the functions when there is no
reference.
Fixes: b0c69b4bac ("usb: host: plat: Enable xHCI plat runtime PM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function is not __init since it can be called for deferred
probing or when unbinding/rebinding the device, and therefore it must
not reference objects in __initdata, as pointed out by this link
time warning:
WARNING: drivers/usb/musb/da8xx.o(.text+0x9d4): Section mismatch in reference from the function da8xx_probe() to the (unknown reference) .init.data:(unknown)
This removes the annotation.
Reported-by: Olof's autobuilder <olof@lixom.net>
Fixes: d6299b6efb ("usb: musb: Add support of CPPI 4.1 DMA controller to DA8xx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate buffers on HEAP instead of STACK for local structures
that are to be received using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Tested-by: Alfredo Rafael Vicente Boix <alviboi@gmail.com>;
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 833415a3e7 ("cdc-wdm: fix "out-of-sync" due to
missing notifications")
There have been several reports of wdm_read returning unexpected EIO
errors with QMI devices using the qmi_wwan driver. The reporters
confirm that reverting prevents these errors. I have been unable to
reproduce the bug myself, and have no explanation to offer either. But
reverting is the safe choice here, given that the commit was an
attempt to work around a firmware problem. Living with a firmware
problem is still better than adding driver bugs.
Reported-by: Kasper Holtze <kasper@holtze.dk>
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Reported-by: Daniele Palmas <dnlplm@gmail.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 833415a3e7 ("cdc-wdm: fix "out-of-sync" due to missing notifications")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates the e-mail address of Phillip Potter, updater of the Nokia 6288
entry in drivers/usb/storage/unusual_devs.h
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.12, including:
- support for devices with up to 16 ports (e.g. some Moxa devices)
- support for endpoint sanity checks in core, which allows for code sharing
and avoids allocating resources for rejected interfaces
- support for endpoint-port remapping, which allows some driver hacks to
be removed as well as omninet to use the generic write implementation
- removal of an obsolete tty open-race workaround which prevented a
port from being opened immediately after having been registered
- generic-driver support for interfaces with just a bulk-in endpoint
- improved ftdi_sio event-char and latency-timer handling
- improved ftdi_sio support for some broken BM chips
Included are also various clean ups and a new ftdi_sio device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=cSzy
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.12-rc1
Here are the USB-serial updates for 4.12, including:
- support for devices with up to 16 ports (e.g. some Moxa devices)
- support for endpoint sanity checks in core, which allows for code sharing
and avoids allocating resources for rejected interfaces
- support for endpoint-port remapping, which allows some driver hacks to
be removed as well as omninet to use the generic write implementation
- removal of an obsolete tty open-race workaround which prevented a
port from being opened immediately after having been registered
- generic-driver support for interfaces with just a bulk-in endpoint
- improved ftdi_sio event-char and latency-timer handling
- improved ftdi_sio support for some broken BM chips
Included are also various clean ups and a new ftdi_sio device id.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
We already have sp_array to store each scratch buffer address for xHC,
it doesn't need another sp_dma_buffers array to store it.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the modern API to request MSI or MSI-X interrupts, which allows us to
get rid of the msix_entries array, as well as cleaning up the cleanup
code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch sets resume_quirk() for R-Car controllers to re-download
the firmware in resume timing. Otherwise, if the controller's power
is down in suspend timing, the firmware in the controller goes away,
and then the controller doesn't work after resume.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds resume_quirk() to do platform specific process in
resume timing.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables the clk in resume timing when device_may_wakeup()
is false. Otherwise, kernel panic happens when R-Car resumes the system
from Suspend-to-RAM because the clk is disabled.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the xHCI plat runtime PM for parent device to suspend/resume
xHCI. Also call pm_runtime_forbid() in probe() function to force users
to explicitly enable runtime pm using power/control in sysfs, in case
some parent devices didn't implement runtime PM callbacks.
[set do_wakeup to true when runtime suspending -Mathias]
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.
Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since when we got rid of usbfs, the /proc/bus/usb is now
elsewhere. Fix references for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add sysfs entry for role switch
- Update gadget state after gadget back from suspend
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY9XecAAoJEEhZKYFQ1nG7PuQH+wR+qFiaswoJA3q+2sdqQDdD
vN1FLT93o3ObgnmYwbZZDxdGeB6e+AJ/K8tQCOVqm8AnaNOzDwCYJoBTa5nPaS5k
c+E4JlciG2NJG1s+eGVhZUPTQD3qS47vkgHymgtlTbQPDJDZy7k5nu7H1GSI7mvM
7AH4uavzMIqsZcQTAln6BvIr2FQHh996LnUHDvYSZ6Y+8cws9IPMbSIiao3s3SiZ
fULYJbVfDOd0LuxHOn7AdKrmlDJ/Gi2vmR4xQLlwvXEYk5/NUcSc1Yo5lVZcDUBR
MzX4bLvhLi4SNLXLJhfqYjXcPXddXxawL/TRGDmT0B/1N8CCtBWJkNpIgx9q6dk=
=opDd
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Two changes for this v4.12-rc1:
- Add sysfs entry for role switch
- Update gadget state after gadget back from suspend
The DMA may hang up if a teardown is initiated while an endpoint is still
active (Advisory 2.3.27 of DA8xx errata).
To workaround this issue, add a delay before to initiate the teardown.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, only the PIO mode is supported.
This add support of CPPI 4.1 to DA8xx.
As in DA8xx the CPPI 4.1 DMA is a part of the USBSS, create the CPPI 4.1
device as a child of USB.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
[b-liu@ti.com: minor tweak in the commit log]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the DA8xx, USB and CPPI 4.1 are sharing the same interrupt line.
Update the driver to request a shared irq.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DIV_ROUND_UP is bit useful than series of "/" and "%" operations.
Replace "/%" sequence with DIV_ROUND_UP macro.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ff6cbf1f ("usb: xhci: Add helper function xhci_set_power_on().")
created a helper to control port power that needs to be called with
xhci->lock held and interrupts disabled.
It released the lock with spin_unlock_irqrestore using a new zero flag
variable instead of the original flag from spin_lock_irqsave.
This regression triggered a static checker warning about bogus flags, and
a null pointer dereference on armada-385.
Fix it by passing a pointer to the correct flags and using it instead
Fixes: a6ff6cbf1f ("usb: xhci: Add helper function xhci_set_power_on().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, the user needs to adjust some properties for controllers, eg
the role for controller, we add sysfs group for them.
The attribute 'role' is used to switch host/gadget role dynamically, the
uewr can read the current role, and write the other role compare to
current one to finish the switch.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Pull SCSI target fixes from Nicholas Bellinger:
"There has been work in a number of different areas over the last
weeks, including:
- Fix target-core-user (TCMU) back-end bi-directional handling (Xiubo
Li + Mike Christie + Ilias Tsitsimpis)
- Fix iscsi-target TMR reference leak during session shutdown (Rob
Millner + Chu Yuan Lin)
- Fix target_core_fabric_configfs.c race between LUN shutdown +
mapped LUN creation (James Shen)
- Fix target-core unknown fabric callback queue-full errors (Potnuri
Bharat Teja)
- Fix iscsi-target + iser-target queue-full handling in order to
support iw_cxgb4 RNICs. (Potnuri Bharat Teja + Sagi Grimberg)
- Fix ALUA transition state race between multiple initiator (Mike
Christie)
- Drop work-around for legacy GlobalSAN initiator, to allow QLogic
57840S + 579xx offload HBAs to work out-of-the-box in MSFT
environments. (Martin Svec + Arun Easi)
Note that a number are CC'ed for stable, and although the queue-full
bug-fixes required for iser-target to work with iw_cxgb4 aren't CC'ed
here, they'll be posted to Greg-KH separately"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcmu: Skip Data-Out blocks before gathering Data-In buffer for BIDI case
iscsi-target: Drop work-around for legacy GlobalSAN initiator
target: Fix ALUA transition state race between multiple initiators
iser-target: avoid posting a recv buffer twice
iser-target: Fix queue-full response handling
iscsi-target: Propigate queue_data_in + queue_status errors
target: Fix unknown fabric callback queue-full errors
tcmu: Fix wrongly calculating of the base_command_size
tcmu: Fix possible overwrite of t_data_sg's last iov[]
target: Avoid mappedlun symlink creation during lun shutdown
iscsi-target: Fix TMR reference leak during session shutdown
usb: gadget: Correct usb EP argument for BOT status request
tcmu: Allow cmd_time_out to be set to zero (disabled)
As some USB documentation files got moved, adjust their
cross-references to their new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
We need an space before a numbered list to avoid those warnings:
./drivers/usb/core/message.c:478: ERROR: Unexpected indentation.
./drivers/usb/core/message.c:479: WARNING: Block quote ends without a blank line; unexpected unindent.
./include/linux/usb/composite.h:455: ERROR: Unexpected indentation.
./include/linux/usb/composite.h:456: WARNING: Block quote ends without a blank line; unexpected unindent.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
-----BEGIN PGP SIGNATURE-----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=wYOI
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.12
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
Update Kconfig help for fifo_mode = 0 to explain the behavior better.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use dev_err() to display EP configuration error to avoid silent failure.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If dr_mode is "otg" then support dual role mode of operation.
Currently this mode is only supported when an extcon handle is
present in the dwc3 device tree node. This is needed to
get the ID status events of the port.
We're using a workqueue to manage the dual-role state transitions
as the extcon notifier (dwc3_drd_notifier) is called in an atomic
context by extcon_sync() and this doesn't go well with
usb_del_gadget_udc() causing a lockdep and softirq warning.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can't have both Host and Peripheral roles active at the same time
because of one detail on DWC3: it shares the same memory area for both
Host and Peripheral registers.
When swapping roles we must reinitialize the new role every
time. Let's make sure this works for our debugfs interface.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Each role is mutually exclusive, the | operator is unnecessary. Remove
it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We're going to use this member to track which role we're currently
playing, that way we can more easily implement dual-role swap in
upcoming patches.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
allow usb_del_gadget_udc() and usb add_gadget_udc() to be called
repeatedly on the same gadget->dev structure.
We need to clear the gadget->dev structure so that kobject_init()
doesn't complain about already initialized object.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's much simpler to just add one extra TRB chained to previous TRB to
handle ZLP. This helps us reduce pointless allocations and simplifies
the code a little bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just like we did for all other endpoint types, let's rely on a chained
TRB pointing to ep0_bounce_addr in order to align transfer size. This
will make the code simpler.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of constantly recomputing how dwc and epnum relate to dep,
just pass dep as argument.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we pass TRB's own address on bpl/bph fields, we can get our SETUP
packet as immediate data on the TRB itself, without having to allocate
extra memory for it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are several inconsistencies in the error handling code.
1. If clk_get() fails, it goes to clk_put().
2. If pdata->phy_init() fails, it does not disable u3d->clk.
3. In case of failure after stopping u3d, it does pdata->phy_deinit()
and clk_disable(u3d->clk) twice.
4. It ignores failures in clk_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check fifo configuration values against device tree values for endpoint fifo
in auto configuration mode (fifo_mode=0).
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently the of glue code in fsl-mph-dr-of will create the platform
device fsl-usb2-udc. As this driver should also be probed by this name,
this patch adds it to the devtypes list.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order to improve usability a tiny bit, we will return strings that
match what our tracepoints return.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When writing, we expect the "otg" string. When showing, we return
"OTG". Let's downcase that word to avoid confusion.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch splits the amd5536udc driver into two -- one that does
pci device registration and the other file that does the rest of
the driver tasks like the gadget/ep ops etc for Synopsys UDC.
This way of splitting helps in exporting core driver symbols which
can be used by any other platform/pci driver that is written for
the same Synopsys USB device controller.
The current patch also includes a change in the Kconfig and Makefile.
A new config option USB_SNP_CORE will be selected automatically when
any one of the platform or pci driver for the same UDC is selected.
Main changes:
- amd5536udc_pci.c: PCI device registration is moved to this file.
- amd5536udc.c:
This file does rest of the core UDC fucntionality.
9 symbols are exported so as to be used by amd5536udc_pci.c.
Module parameter definitions are moved to header file.
- amd5536udc.h:
Function declarations, module parameters definitions and few common
header file includes are added to this file
- Kconfig:
New USB_SNP_CORE option is added which will be auto selected when
any pci or platform driver config option for the UDC is chosen.
- Makefile:
Compiles the core and pci files separately.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for usb role swap via sysfs "role".
For example:
1) Connect a usb cable using 2 Salvator-X boards.
- For A-Device, the cable is connected to CN11 (USB3.0 ch0).
- For B-Device, the cable is connected to CN9 (USB2.0 ch0).
2) On A-Device, you input the following command:
# echo peripheral > /sys/devices/platform/soc/ee020000.usb/role
3) On B-Device, you input the following command:
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Then, the A-Device acts as a peripheral and the B-Device acts as
a host. Please note that A-Device must input the following command
if you want the board to act as a host again.
# echo host > /sys/devices/platform/soc/ee020000.usb/role
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Minor code cleanup based on feedback received on mailinglist.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds extcon support to see VBUS/ID signal states.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This usb 3.0 peripheral controller has a register (USB_OTG_STA) to monitor
the USB ID signal. So, this patch adds the ID signal monitoring to change
the mode to host (A-Host) or peripheral (B-Peripheral).
This patch also removes hardcoded setting as B-Peripheral mode.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If usb/otg-fsm.h and usb/composite.h are included together
then it results in the build warning [1].
Prevent that by defining VDBG locally.
Also get rid of MPC_LOC which doesn't seem to be used
by anyone.
[1] - warning fixed by this patch:
In file included from drivers/usb/dwc3/core.h:33,
from drivers/usb/dwc3/ep0.c:33:
include/linux/usb/otg-fsm.h:30:1: warning: "VDBG" redefined
In file included from drivers/usb/dwc3/ep0.c:31:
include/linux/usb/composite.h:615:1: warning: this is the location
of the previous definition
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To avoid checkpatch warnings with new patches let's
start using the BIT() macro wherever possible.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently ffs_dev::name can be either allocated by the client of
the ffs_dev structure or by the f_fs.c core itself. The former
is used by g_ffs while the latter happens with configfs.
Historically, g_ffs did not need to allocate separate buffer for
the name so what is now f_fs.c core never cared about freeing
that space. With configfs the name needs to be copied since the
memory is not guaranteed to be availeble after ffs_set_inst_name
finishes.
The complication is therefore here to avoid allocations in the
g_ffs case but it complicates the code inproportinally to
benefits it provides. In particular, g_ffs is considered
‘legacy’ so optimising for its sake is unlikely to be worth the
effort.
With that observation in mind, simplify the code by unifying the
code paths in g_ffs and configfs paths. Furthermore, instead of
allocating a new buffer for the name, simply embed it in the
ffs_dev structure. This further makes the memory management
less convoluted and error-prone.
The configfs interface for functionfs imposed a limit of 40
characters for the name so this results in a 41-byte buffer
added to the structure. (For short names this may lead to
wasted memory but the actual amount is not immediately obvious
and depends on pointer size and which slab buckets the structure
and name would fall into).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since the old common Samsung USB PHY code has been removed by commit ea2fdf8423
("usb: phy: samsung: remove old common USB PHY code"), thus remove the unused
config.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes the commit: 1cd8fd2887 ("usb: gadget: dummy_hcd: add
SuperSpeed support").
In the case of ClearPortFeature and USB_PORT_FEAT_POWER, simply clear
the right bit regardless of what the wValue is.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Unless HW sets quirk_ep_out_aligned_size, gadget driver shouldn't make
any efforts towards aligning transfers. If the UDC needs, it *must*
set the quirk flag.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have helpers for some of these, let's rely on them instead of open
coding what they do in u_ether.c
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As USB_CONFIGFS is not a part of the "USB Gadget Drivers" choice
anymore, the name for the option and its attached description needs to
be more descriptive. It appears one level higher in the configuration
menu, and without the context provided by the comments for the choice
entry, it needs to make sense on its own.
Conversely, the "USB Gadget Drivers" entry now only introduces the
legacy drivers, where one or more functions are combined in a single
driver. As the configfs option can be used as a full-fledged
alternative, rename the choice entry to show that it is not the only
way to provice service as an USB gadget.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With commit bc49d1d17d ("usb: gadget: don't couple configfs to legacy
gadgets"),it is possible to build a modular kernel with both built-in
configfs support and modular legacy gadget drivers.
But when building a kernel without modules, it is also necessary to be
able to build with configfs but without any legacy gadget driver. This
was a possible configuration when the USB_CONFIGFS was a part of the
choice options, but not anymore.
Mark the choice for legacy gadget drivers as optional restores this.
Fixes: bc49d1d17d ("usb: gadget: don't couple configfs to legacy gadgets")
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget wants to set the starting microframe for the first ISOC TRB
to 4 microframes in the future, but it does so by multiplying the
dep->interval. This only works if dep->interval = 1. For other intervals
it will put it 4 *intervals* in the future which may be way too much.
Fix so that it always adds just one interval or at least 4 microframes.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Change goto labels to meaningful names from a series of errNs.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A previous patch in the series reduces the number of callsites of
dwc3_gadget_init_hw_endpoints from two to one. This patch removes the
redundant step of wrappering one function in the other, which can be done
by adding a parameter to dwc3_gadget_init_endpoints and moving the
linked-list initialization of dwc->gadet.ep_list.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- DWC_USB3_NUM indicates the number of Device mode single directional
endpoints, including OUT and IN endpoint 0.
- DWC_USB3_NUM_IN_EPS indicates the maximum number of Device mode IN
endpoints active at any time, including control endpoint 0.
It's possible to configure RTL such that DWC_USB3_NUM_EPS is equal to
DWC_USB3_NUM_IN_EPS.
dwc3-core calculates the number of OUT endpoints as DWC_USB3_NUM minus
DWC_USB3_NUM_IN_EPS. If RTL has been configured with DWC_USB3_NUM_IN_EPS
equal to DWC_USB3_NUM then dwc3-core will calculate the number of OUT
endpoints as zero.
For example a from dwc3_core_num_eps() shows:
[ 1.565000] /usb0@f01d0000: found 8 IN and 0 OUT endpoints
This patch refactors the endpoint calculation down to one variable
dwc->num_eps taking care to maintain the current mapping of endpoints for
fixed FPGA configurations as described in Table 4-7 of version 2.60a of the
DWC USB3 databook.
The endpoint mapping will then be EP-OUT, EP-IN etc, up to DWC_USB3_NUM.
If DWC_USB3_NUM is odd then OUT will take the extra endpoint.
Suggested-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We must make sure that our macros are safe against expressions passed
as arguments. We have seen one problem where GTXFIFOSIZ(n) was failing
when passed the expression (epnum >> 1) as argument. The problem was
caused by operator precedence between >> and *.
To make sure macros are safe, we just wrap argument with () when using
it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch introduces a new parameter to activate USB OTG HS/FS core
embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register
to enable the transceiver.
Also add the dwc2_set_params function for stm32f4 otg fs.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove unnecessary variable and update function prototype.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rewrite udc_free_dma_chain() function to avoid use of pointer after free.
Addresses-Coverity-ID: 1091172
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
I had seen some odd behavior with HiKey's usb-gadget interface
that I finally seemed to have chased down. Basically every other
time I plugged in the OTG port, the gadget interface would
properly initialize. The other times, I'd get a big WARN_ON
in dwc2_hsotg_init_fifo() about the fifo_map not being clear.
Ends up if we don't disconnect the gadget state, the fifo-map
doesn't get cleared properly, which causes WARN_ON messages and
also results in the device not properly being setup as a gadget
every other time the OTG port is connected.
So this patch adds a call to dwc2_hsotg_disconnect() in the
reset path so the state is properly cleared.
With it, the gadget interface initializes properly on every
plug in.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 76e0da34c7 ("usb-gadget/uvc: use per-attribute show and store
methods") caused a stringification of an undefined macro argument "aname",
so three UVC parameters (streaming_interval, streaming_maxpacket and
streaming_maxburst) were named "aname".
Add the definition of "aname" to the main macro and name the filenames as
originaly intended.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Drop redundant calls to tty_buffer_request_room and use the more
efficient tty_insert_flip_char when inserting single characters.
Signed-off-by: Johan Hovold <johan@kernel.org>
The transfer buffers and URBs are allocated and initialised by USB
serial core during probe, and there's no need to check for NULL transfer
buffers in the bulk-in completion handlers.
Signed-off-by: Johan Hovold <johan@kernel.org>
As per [1] issue #4,
"The periodic EP scheduler always tries to schedule the EPs
that have large intervals (interval equal to or greater than
128 microframes) into different microframes. So it maintains
an internal counter and increments for each large interval
EP added. When the counter is greater than 128, the scheduler
rejects the new EP. So when the hub re-enumerated 128 times,
it triggers this condition."
This results in Bandwidth error when devices with periodic
endpoints (ISO/INT) having bInterval > 7 are plugged and
unplugged several times on a TUSB73x0 XHCI host.
Workaround this issue by limiting the bInterval to 7
(i.e. interval to 6) for High-speed or faster periodic endpoints.
[1] - http://www.ti.com/lit/er/sllz076/sllz076.pdf
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_decode_trb() treats a link trb in the same way as that for
an event trb. This patch fixes this by decoding the link trb
according to the spec.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI context changes have already been traced by the trace
events. It's unnecessary to put the same message in kernel
log. This patch removes the use of xhci_dbg_ctx().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every XHCI TRB has already been traced by the trb trace events.
It is unnecessary to put the same message in kernel log. This
patch removes xhci_debug_trb().
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XHCI ring changes have already been traced by the ring trace
events. It's unnecessary to put the same messages in kernel
log. This patch removes the debugging code for a ring.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enq_updates and deq_updates were introduced in the first place
to check whether an xhci hardware is able to respond to trbs
enqueued in the ring. We now have trb tracers to trace every
single enqueue/dequeue trb. It's time to remove them and the
associated debugging code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several functions have a single user in the same file where it
is defined. There's no need to expose it anywhere else.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_dbg_ep_rings() isn't used in xhci driver anymore. Remove
it to reduce the module binary size.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch creates a new event class called xhci_log_ring, and
defines the events used for tracing the change of all kinds of
rings used by an xhci host. An xHCI ring is basically a memory
block shared between software and hardware. By tracing changes
of rings, it makes the life easier for debugging hardware or
software problems.
This info can be used, later, to print, in a human readable way,
the life cycle of an xHCI ring using the trace-cmd tool and the
appropriate plugin.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new xhci_hc_died() function that takes care of handling
pending commands and URBs if a host controller becomes unresponsive.
This addresses issues on hotpluggable xhci controllers that disappear
from the bus suddenly, often while the bus (PCI) remove function is
still being processed.
xhci_hc_died() sets a XHCI_STATUS_DYING flag to prevent new URBs and
commands or to be queued. The flag also ensures xhci_hc_died() will
give back pending commands and URBs once.
Host is considered dead if register read returns 0xffffffff, or host
fails to abort the command ring, or fails stopping an endpoint after
trying for 5 seconds.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't halt the host controller immediately when first HCD is removed as
it will cause problems if we have devices attached to the second (primary)
HCD, like a keyboard.
We've been carrying this in our Linux-as-a-bootloader environment for a
little while now. The machines all have the same TI TUSB73x0 part,
and when we kexec the devices don't come back until a system power cycle.
[minor adjustments, code comments and remove HALT check -Mathias]
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's one annoyance in how xhci prints debug messages, we often
get logs with messages but it's hard to say from which device and
endpoint the message originates. Add slot_id, ep_index messages
in handle_tx_event.
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Format for each TRB in each control transfer stage differs. Let's make
sure we correctly pretty print these fields to avoid confusion.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With these, we can track what's happening with the HW while executing
each and every command. It will give us visibility into how the
different contexts are being modified by xHC which can bring insight
into problems while debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By extracting and exposing xhci_slot_state_string() in a header file, we
can re-use it to print Slot Context State from our tracepoints, which
can aid in tracking down problems related to command execution.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will help us figuring out which device $this URB belongs to while
debugging.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For usb2 ports, the port test mode Test_J_State, Test_K_State,
Test_Packet, Test_SE0_NAK and Test_Force_En can be enabled
as described in usb2 spec.
USB2 test mode is a required hardware feature for system integrators
validating their hardware according to USB spec, regarding signal
strength and stuff. It is purely a hardware test feature.
Usually you need an oscilloscope and have to enable those test modes on
the hardware. This will send some specific test patterns on D+/D-. There
is no report available (in Linux itself) as it is purely externally
visible. Regular USB usage is not possible at that time.
Anyone (well access to e.g. /dev/bus/usb/001/001 provided) can use it by
sending appropriate USB_PORT_FEAT_TEST requests to the hub.
[Add better commit message by Alexander Stein -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the visability of xhci_start() so that it
can be used when enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring slot disable related code into a helper
function xhci_disable_slot() which can be used when
enabling test mode.
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring port power on/off related code into
a helper function xhci_set_power_on() which can
be reused when enabling test mode.
[set port state to neutral before writing port power -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EINT(Event Interrupt) is a write-1-to-clear type of bit in xhci
status register. It should be cleared by writing a 1. Writing 0
to this bit has no effect.
Xhci driver tries to clear this bit by writing 0 to it. This is
not the right way to go. This patch corrects this by reading the
register first, then clearing all RO/RW1C/RsvZ bits and setting
the clearing bit, and writing back the new value at last.
Xhci spec requires that software that uses EINT shall clear it
prior to clearing any IP flags in section 5.4.2. This is the
reason why this patch is CC'ed stable as well.
[old way didn't cause any issues, skip stable, send to next -Mathias]
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB host controllers can take a significant amount of time to suspend
and resume, adding several hundred miliseconds to the kernel resume
time. Since the XHCI controller has no outside dependencies (other than
clocks, which are suspended late/resumed early), allow it to suspend and
resume asynchronously.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Andrew Bresticker <abrestic@chromium.org>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhci_tx_urb() should be able to get the vhci_device from
its caller vhci_urb_enqueue(), instead of brutal-force
searching it.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Yuyang Du <yuyang.du@intel.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code refactoring to make the flow easier to follow.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8c06e407e ("usb: separate out sysdev pointer from
usb_bus") converted to use hcd->self.sysdev for DMA
operations instead of hcd->self.controller but forgot to do
it for one instance.
This gets caught when DMA debugging is enabled since dma map
and unmap end up using different device pointers.
Fix it.
Fixes: a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
Reported-by: Carlos Hernandez <ceh@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
write_used was introduced with commit 884b600f63 ("[PATCH] USB: fix acm
trouble with terminals") but never used since.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a similar log message to USB_CDC_NOTIFY_SERIAL_STATE as it is
already done with USB_CDC_NOTIFY_NETWORK_CONNECTION.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB devices may have very limited endpoint packet sizes, so that
notifications can not be transferred within one single usb packet.
Reassembling of multiple packages may be necessary.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Notifications may only be 8 bytes long. Accessing the 9th and
10th byte of unimplemented/unknown notifications may be insecure.
Also check the length of known notifications before accessing anything
behind the 8th byte.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a65a6f14dc ("USB: serial: fix race between probe and open")
fixed a race between probe and open, which could lead to crashes when a
not yet fully initialised port was being opened.
This race was later incidentally closed by commit 7e73eca6a7 ("TTY:
move cdev_add to tty_register_device") which moved character-device
registration from tty_register_driver to tty_register_device, which
isn't called until the port has been fully set up.
Remove the now redundant workaround which had the negative side effect
of not allowing a port to be opened immediately after user space had
been notified of a new tty device.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).
That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the argument in usb_ep_free_request as it is
mistakenly set to ep_out. It should be ep_in for status request.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Drop some unnecessary termios-flag debugging that have been faithfully
reproduced in a few old drivers, including the "clfag" typo and all.
This also addresses a compiler warning on sparc where tcflag_t is
unsigned long and would have required an explicit cast.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Commit fd567653bd ("usb: phy: isp1301: Add OF device ID table")
added an OF device ID table, but used the of_match_ptr() macro
that will lead to a build warning if CONFIG_OF symbol is disabled:
drivers/usb/phy//phy-isp1301.c:36:34: warning: ‘isp1301_of_match’ defined but not used [-Wunused-const-variable=]
static const struct of_device_id isp1301_of_match[] = {
^~~~~~~~~~~~~~~~
Fixes: fd567653bd ("usb: phy: isp1301: Add OF device ID table")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci needs to take care of four scenarios when asked to cancel a URB.
1 URB is not queued or already given back.
usb_hcd_check_unlink_urb() will return an error, we pass the error on
2 We fail to find xhci internal structures from urb private data such as
virtual device and endpoint ring.
Give back URB immediately, can't do anything about internal structures.
3 URB private data has valid pointers to xhci internal data, but host is
not responding.
give back URB immedately and remove the URB from the endpoint lists.
4 Everyting is working
add URB to cancel list, queue a command to stop the endpoint, after
which the URB can be turned to no-op or skipped, removed from lists,
and given back.
We failed to give back the urb in case 2 where the correct device and
endpoint pointers could not be retrieved from URB private data.
This caused a hang on Dell Inspiron 5558/0VNM2T at resume from suspend
as urb was never returned.
[ 245.270505] INFO: task rtsx_usb_ms_1:254 blocked for more than 120 seconds.
[ 245.272244] Tainted: G W 4.11.0-rc3-ARCH #2
[ 245.273983] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 245.275737] rtsx_usb_ms_1 D 0 254 2 0x00000000
[ 245.277524] Call Trace:
[ 245.279278] __schedule+0x2d3/0x8a0
[ 245.281077] schedule+0x3d/0x90
[ 245.281961] usb_kill_urb.part.3+0x6c/0xa0 [usbcore]
[ 245.282861] ? wake_atomic_t_function+0x60/0x60
[ 245.283760] usb_kill_urb+0x21/0x30 [usbcore]
[ 245.284649] usb_start_wait_urb+0xe5/0x170 [usbcore]
[ 245.285541] ? try_to_del_timer_sync+0x53/0x80
[ 245.286434] usb_bulk_msg+0xbd/0x160 [usbcore]
[ 245.287326] rtsx_usb_send_cmd+0x63/0x90 [rtsx_usb]
Reported-by: diego.viola@gmail.com
Tested-by: diego.viola@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A control transfer that stopped at the status stage incorrectly
warned about a "unexpected TRB Type 4", and did not set the
transferred actual_length for the URB.
The URB actual_length for control transfers should contain the
bytes transferred in the data stage.
Bytes of a partially sent setup stage and missing bytes from
status stage should be left out.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shutdown should be called for xhci_plat devices especially for
situations where kexec might be used by stopping DMA
transactions.
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is race condition when two USB class drivers try to call
init_usb_class at the same time and leads to crash.
code path: probe->usb_register_dev->init_usb_class
To solve this, mutex locking has been added in init_usb_class() and
destroy_usb_class().
As pointed by Alan, removed "if (usb_class)" test from destroy_usb_class()
because usb_class can never be NULL there.
Signed-off-by: Ajay Kaher <ajay.kaher@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new endpoint helpers to lookup the required bulk-in and bulk-out
endpoints, and the optional interrupt-in endpoint.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new endpoint helpers to lookup the required interrupt-in
endpoint.
Note that this in fact both loosens and tightens the endpoint sanity
check by accepting any interface with an interrupt-in endpoint rather
than always using the first endpoint without verifying its type.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setup each port to use the first bulk-out endpoint in calc_num_ports so
that core allocates the corresponding port resources for us.
Signed-off-by: Johan Hovold <johan@kernel.org>
Setup each port to use the first bulk-out endpoint in calc_num_ports so
that core allocates the corresponding port resources for us.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add an explicit sanity check to make sure we have the expected
endpoints. This will provide a descriptive error message in case an
expected endpoint is missing when probing.
Note that the driver already gracefully fails to probe (albeit with a
less descriptive error message) if a bulk-in endpoint is missing, and an
attempt to write to a port whose device lack a bulk-out endpoint would
fail with -ENODEV.
Signed-off-by: Johan Hovold <johan@kernel.org>
Print a message and register two ports for interfaces for which we do
not know how many ports there are instead of binding, allocating
resources, but not register any ports.
This provides a hint that anyone adding a dynamic device id must also
provide a reference id (driver info) from which the port count can be
retrieved, for example:
echo <vid> <pid> 0 0x110A 0x1410 > new_id
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new endpoint-remap functionality to configure the ports for
treo devices instead of poking around in the port structures after the
ports have been setup.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new endpoint-remap functionality to configure the ports for
clie_5 devices.
Note that the same bulk-out endpoint is being used for both ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the redundant calc_num_ports callback from the clie_5 type, for
which the callback always returns zero and hence falls back to the type
num_ports value (2).
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices always require at least one bulk-out endpoint so let core
verify that.
This avoids attempting to send bulk data to the default pipe when
downloading firmware in boot mode.
Note that further endpoints are still needed when not in boot mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that the endpoint-port mapping has been properly set up during
probe, we can switch to using the more efficient generic write
implementation.
Note that this currently means that chars_in_buffer now overcounts
slightly as we always write a full endpoint-sized packet.
Also add a copyright entry.
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices use the second bulk-out endpoint for writing. Instead of
using the resources of the second port structure setup by core, use the
new endpoint-remap functionality to simply ignore the first bulk-out
endpoint. This specifically avoids allocating resources for the unused
endpoint.
Note that the disconnect callback was always redundant as all URBs would
have been killed by USB core on disconnect.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the endpoint sanity check by letting core verify the single
interrupt endpoint, and verifying the bulk endpoints in calc_num_ports
after having determined the number of ports.
Note that the static type num_ports field was neither correct or used
(since calc_num_ports never returns zero).
Signed-off-by: Johan Hovold <johan@kernel.org>
This driver have treated the interrupt endpoint as optional despite it
always being present (according to the datasheet). Let's consider it
mandatory instead.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the mcs7715 port setup by using the new endpoint-remap
functionality provided by core. Instead of poking around in internal
port-structure fields, simply swap the endpoint descriptors of the two
ports in calc_num_ports before the port structures are even allocated.
Note that we still need to override the default interrupt completion
handler.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the redundant read-urb check from open. The presence of a bulk-in
endpoint is now verified during probe and core has allocated the
corresponding resources.
Signed-off-by: Johan Hovold <johan@kernel.org>
Verify that the required interrupt endpoint is present at probe rather
than at open to avoid allocating resources for an unusable device.
Note that the endpoint is only required when in download mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices always require at least one bulk-out endpoint so let core
verify that.
This avoids attempting to send bulk data to the default pipe when
downloading firmware in boot mode.
Note that further endpoints are still needed when not in boot mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than attach callback to verify that the
required endpoints are present when in download mode.
This avoids allocating port resources for interfaces that won't be bound.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports callback to ignore unused endpoints.
The driver binds to any interface with at least one bulk-in and one
bulk-out endpoint, but some devices can have three or more endpoints of
which only either the first or second pair of endpoints is needed.
This avoids allocating resources for unused endpoints, and specifically
a port is no longer registered for the unused first endpoint pair when
there are more than three endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than attach callback to determine which
interface to bind to in order to avoid allocating port-resources for
interfaces that won't be bound.
Signed-off-by: Johan Hovold <johan@kernel.org>
We can now abort probe early after an error in calc_num_ports by
returning an errno instead of attempting to continue probing but not
register any ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present and moving the max-packet check to
calc_num_ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than probe callback to determine which
interface to bind to.
This allows us to remove some duplicate code.
Signed-off-by: Johan Hovold <johan@kernel.org>
Implement the "horrible endpoint hack" for some legacy devices as a
quirk and clean up the code somewhat.
Note that the bulk-endpoint check can be removed as core will already
have verified this.
Signed-off-by: Johan Hovold <johan@kernel.org>
Some pl2303 devices require the use of the interrupt endpoint of an
unrelated interface. This has so far been dealt with in usb-serial core,
but can now be moved to a driver calc_num_ports callback.
Note that we relax the endpoint requirements checked by core and instead
verify that we have an interrupt-in endpoint in calc_num_ports for all
devices so that the hack can first be applied.
Signed-off-by: Johan Hovold <johan@kernel.org>
Relax the generic driver bulk-endpoint requirement. The driver handles
devices without bulk-out endpoints just fine these days.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a calc_num_ports callback to the generic driver and verify that the
device has the required endpoints there instead of in core.
Note that the generic driver num_ports field was never used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a probe callback to the generic driver and print the
only-for-testing message there.
This is a first step in getting rid of the CONFIG_USB_SERIAL_GENERIC
ifdef from usb-serial core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow subdrivers to modify the port-endpoint mapping by passing the
endpoint descriptors to calc_num_ports.
The callback can now also be used to verify that the required endpoints
exists and abort probing otherwise.
This will allow us to get rid of a few hacks in subdrivers that are
already modifying the port-endpoint mapping (or aborting probe due to
missing endpoints), but only after the port structures have been setup.
Signed-off-by: Johan Hovold <johan@kernel.org>
Functions udc_enable() and udc_disable() have a duplicated prototype.
Remove it.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_log_msg trace class isn't used any more. Suggest to remove it.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
