Pull more vfs mount updates from Al Viro:
"Propagation of new syscalls to other architectures + cosmetic change
from Christian (fscontext didn't follow the convention for anon inode
names)"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
uapi: Wire up the mount API syscalls on non-x86 arches [ver #2]
uapi, x86: Fix the syscall numbering of the mount API syscalls [ver #2]
uapi, fsopen: use square brackets around "fscontext" [ver #2]
Christoph Hellwig writes:
This is a series doing two somewhat interwinded things. It improves
the asm-generic nommu uaccess helper to optionally be entirely generic
and not require any arch helpers for the actual uaccess. For the
generic uaccess.h to actually be generically useful I also had to kill
off the mess we made of <asm/segment.h>, which really shouldn't exist
on most architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJcv22JAAoJEGCrR//JCVInH3YP/i7hVIEo4azoRB3/PwFTPel8
Buq9BUrGy1kptLWyi1yuOZf874gF6351hkVUo4EYq/uZ3x41ciojxFgbsIriAU0p
2xzJAWY0YaVuWM+PIVj6KjyDA0N7/U5PcAG+03pl1Lhf0GHldmMbQIWt8D8HXbB8
gyaOeBGM9BneKd8Xu0COUaId9/3GXUwsy2zYc77+PxaHHYJzGDPB5lqNdU0gbB54
P9uXI2mpoAepFMsFgP6/FBvT/jCiMifRIdTXPD94NtjfG+Q4lo+LBQ6bpcLfw4ZD
VNh0982Cyl5n7FNetlTK4CPBn0RZsmBRriMotYfXeghFg0mmNTLwNEMg1u6RQ+uq
VYoBrVGhnx4SFB8xdkqO4md6UwprR2SERIIKwuCTbhwSgs+NkB7t4ftOwTzyQ1/6
7WQjclAIxQK9J7uwAeRGCvyrNJplqSfOA/hRjuq/Z0BCE/+m26Gxfv4aDztU5wFO
FWj2uFGTMuufp+DKoh5Vj5aJiFwfqK5/w1VYWSQdaoiWsHlmmu5IkTrrZyz+S3Tj
cifO9Ghe75Pt+rDllc8yqzKYXa5mL89sWyKiy+2ItOvGVh5EqXBbPXtCrFFIHRFL
WojVPu0yO+OoP0sEdamT/4FxbWO9VrV5YXdaRg/GjVA9ARlKNpFrZbuHtvEitwpi
7AbhxMZwBSSb9R3cz67J
=X2CH
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-nommu' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull nommu generic uaccess updates from Arnd Bergmann:
"asm-generic: kill <asm/segment.h> and improve nommu generic uaccess helpers
Christoph Hellwig writes:
This is a series doing two somewhat interwinded things. It improves
the asm-generic nommu uaccess helper to optionally be entirely
generic and not require any arch helpers for the actual uaccess.
For the generic uaccess.h to actually be generically useful I also
had to kill off the mess we made of <asm/segment.h>, which really
shouldn't exist on most architectures"
* tag 'asm-generic-nommu' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: optimize generic uaccess for 8-byte loads and stores
asm-generic: provide entirely generic nommu uaccess
arch: mostly remove <asm/segment.h>
asm-generic: don't include <asm/segment.h> from <asm/uaccess.h>
Wire up the mount API syscalls on non-x86 arches.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- Removing of non-DYNAMIC_FTRACE from 32bit x86
- Removing of mcount support from x86
- Emulating a call from int3 on x86_64, fixes live kernel patching
- Consolidated Tracing Error logs file
Minor updates:
- Removal of klp_check_compiler_support()
- kdb ftrace dumping output changes
- Accessing and creating ftrace instances from inside the kernel
- Clean up of #define if macro
- Introduction of TRACE_EVENT_NOP() to disable trace events based on config
options
And other minor fixes and clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXNxMZxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qq4PAP44kP6VbwL8CHyI2A3xuJ6Hwxd+2Z2r
ip66RtzyJ+2iCgEA2QCuWUlEt2bLpF9a8IQ4N9tWenSeW2i7gunPb+tioQw=
=RVQo
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The major changes in this tracing update includes:
- Removal of non-DYNAMIC_FTRACE from 32bit x86
- Removal of mcount support from x86
- Emulating a call from int3 on x86_64, fixes live kernel patching
- Consolidated Tracing Error logs file
Minor updates:
- Removal of klp_check_compiler_support()
- kdb ftrace dumping output changes
- Accessing and creating ftrace instances from inside the kernel
- Clean up of #define if macro
- Introduction of TRACE_EVENT_NOP() to disable trace events based on
config options
And other minor fixes and clean ups"
* tag 'trace-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
x86: Hide the int3_emulate_call/jmp functions from UML
livepatch: Remove klp_check_compiler_support()
ftrace/x86: Remove mcount support
ftrace/x86_32: Remove support for non DYNAMIC_FTRACE
tracing: Simplify "if" macro code
tracing: Fix documentation about disabling options using trace_options
tracing: Replace kzalloc with kcalloc
tracing: Fix partial reading of trace event's id file
tracing: Allow RCU to run between postponed startup tests
tracing: Fix white space issues in parse_pred() function
tracing: Eliminate const char[] auto variables
ring-buffer: Fix mispelling of Calculate
tracing: probeevent: Fix to make the type of $comm string
tracing: probeevent: Do not accumulate on ret variable
tracing: uprobes: Re-enable $comm support for uprobe events
ftrace/x86_64: Emulate call function while updating in breakpoint handler
x86_64: Allow breakpoints to emulate call instructions
x86_64: Add gap to int3 to allow for call emulation
tracing: kdb: Allow ftdump to skip all but the last few entries
tracing: Add trace_total_entries() / trace_total_entries_cpu()
...
This prepares to move CONFIG_OPTIMIZE_INLINING from x86 to a common
place. We need to eliminate potential issues beforehand.
If it is enabled for s390, the following error is reported:
In file included from arch/s390/crypto/des_s390.c:19:
arch/s390/include/asm/cpacf.h: In function 'cpacf_query':
arch/s390/include/asm/cpacf.h:170:2: warning: asm operand 3 probably doesn't match constraints
asm volatile(
^~~
arch/s390/include/asm/cpacf.h:170:2: error: impossible constraint in 'asm'
Link: http://lkml.kernel.org/r/20190423034959.13525-5-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most architectures do not need the memblock memory after the page
allocator is initialized, but only few enable ARCH_DISCARD_MEMBLOCK in the
arch Kconfig.
Replacing ARCH_DISCARD_MEMBLOCK with ARCH_KEEP_MEMBLOCK and inverting the
logic makes it clear which architectures actually use memblock after
system initialization and skips the necessity to add ARCH_DISCARD_MEMBLOCK
to the architectures that are still missing that option.
Link: http://lkml.kernel.org/r/1556102150-32517-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All callers of arch_remove_memory() ignore errors. And we should really
try to remove any errors from the memory removal path. No more errors are
reported from __remove_pages(). BUG() in s390x code in case
arch_remove_memory() is triggered. We may implement that properly later.
WARN in case powerpc code failed to remove the section mapping, which is
better than ignoring the error completely right now.
Link: http://lkml.kernel.org/r/20190409100148.24703-5-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Oscar Salvador <osalvador@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Arun KS <arunks@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Andrew Banman <andrew.banman@hpe.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch_add_memory, __add_pages take a want_memblock which controls whether
the newly added memory should get the sysfs memblock user API (e.g.
ZONE_DEVICE users do not want/need this interface). Some callers even
want to control where do we allocate the memmap from by configuring
altmap.
Add a more generic hotplug context for arch_add_memory and __add_pages.
struct mhp_restrictions contains flags which contains additional features
to be enabled by the memory hotplug (MHP_MEMBLOCK_API currently) and
altmap for alternative memmap allocator.
This patch shouldn't introduce any functional change.
[akpm@linux-foundation.org: build fix]
Link: http://lkml.kernel.org/r/20190408082633.2864-3-osalvador@suse.de
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On systems without CONTIG_ALLOC activated but that support gigantic pages,
boottime reserved gigantic pages can not be freed at all. This patch
simply enables the possibility to hand back those pages to memory
allocator.
Link: http://lkml.kernel.org/r/20190327063626.18421-5-alex@ghiti.fr
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Acked-by: David S. Miller <davem@davemloft.net> [sparc]
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This condition allows to define alloc_contig_range, so simplify it into a
more accurate naming.
Link: http://lkml.kernel.org/r/20190327063626.18421-4-alex@ghiti.fr
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various architectures including x86 poison the freed initrd memory. Do
the same in the generic free_initrd_mem implementation and switch a few
more architectures that are identical to the generic code over to it now.
Link: http://lkml.kernel.org/r/20190213174621.29297-9-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Steven Price <steven.price@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To facilitate additional options to get_user_pages_fast() change the
singular write parameter to be gup_flags.
This patch does not change any functionality. New functionality will
follow in subsequent patches.
Some of the get_user_pages_fast() call sites were unchanged because they
already passed FOLL_WRITE or 0 for the write parameter.
NOTE: It was suggested to change the ordering of the get_user_pages_fast()
arguments to ensure that callers were converted. This breaks the current
GUP call site convention of having the returned pages be the final
parameter. So the suggestion was rejected.
Link: http://lkml.kernel.org/r/20190328084422.29911-4-ira.weiny@intel.com
Link: http://lkml.kernel.org/r/20190317183438.2057-4-ira.weiny@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marshall <hubcap@omnibond.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of Linux 5.1, alpha and s390 are the last architectures that
have defconfig in arch/*/ instead of arch/*/configs/.
$ find arch -name defconfig | sort
arch/alpha/defconfig
arch/arm64/configs/defconfig
arch/csky/configs/defconfig
arch/nds32/configs/defconfig
arch/riscv/configs/defconfig
arch/s390/defconfig
The arch/$(ARCH)/defconfig is the hard-coded default in Kconfig,
and I want to deprecate it after evacuating the remaining defconfig
into the standard location, arch/*/configs/.
Define KBUILD_DEFCONFIG like other architectures, and move defconfig
into the configs/ subdirectory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The only purpose of klp_check_compiler_support() is to make sure that we
are not using ftrace on x86 via mcount (because that's executed only after
prologue has already happened, and that's too late for livepatching
purposes).
Now that mcount is not supported by ftrace any more, there is no need for
klp_check_compiler_support() either.
Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1905102346100.17054@cbobk.fhfr.pm
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix the following build error when the kernel is built with CONFIG_KASAN
broken since commit 98587c2d89 ("s390: simplify disabled_wait"):
arch/s390/mm/kasan_init.c: In function 'kasan_early_panic':
arch/s390/mm/kasan_init.c:31:2: error: too many arguments to function
'disabled_wait'
31 | disabled_wait(0);
Fixes: 98587c2d89 ("s390: simplify disabled_wait")
Reported-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
-----BEGIN PGP SIGNATURE-----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=p8Fp
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"We've got a reasonably broad set of audit patches for the v5.2 merge
window, the highlights are below:
- The biggest change, and the source of all the arch/* changes, is
the patchset from Dmitry to help enable some of the work he is
doing around PTRACE_GET_SYSCALL_INFO.
To be honest, including this in the audit tree is a bit of a
stretch, but it does help move audit a little further along towards
proper syscall auditing for all arches, and everyone else seemed to
agree that audit was a "good" spot for this to land (or maybe they
just didn't want to merge it? dunno.).
- We can now audit time/NTP adjustments.
- We continue the work to connect associated audit records into a
single event"
* tag 'audit-pr-20190507' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: (21 commits)
audit: fix a memory leak bug
ntp: Audit NTP parameters adjustment
timekeeping: Audit clock adjustments
audit: purge unnecessary list_empty calls
audit: link integrity evm_write_xattrs record to syscall event
syscall_get_arch: add "struct task_struct *" argument
unicore32: define syscall_get_arch()
Move EM_UNICORE to uapi/linux/elf-em.h
nios2: define syscall_get_arch()
nds32: define syscall_get_arch()
Move EM_NDS32 to uapi/linux/elf-em.h
m68k: define syscall_get_arch()
hexagon: define syscall_get_arch()
Move EM_HEXAGON to uapi/linux/elf-em.h
h8300: define syscall_get_arch()
c6x: define syscall_get_arch()
arc: define syscall_get_arch()
Move EM_ARCOMPACT and EM_ARCV2 to uapi/linux/elf-em.h
audit: Make audit_log_cap and audit_copy_inode static
audit: connect LOGIN record to its syscall record
...
-----BEGIN PGP SIGNATURE-----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=LH11
-----END PGP SIGNATURE-----
Merge tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd updates from Christian Brauner:
"This patchset makes it possible to retrieve pidfds at process creation
time by introducing the new flag CLONE_PIDFD to the clone() system
call. Linus originally suggested to implement this as a new flag to
clone() instead of making it a separate system call.
After a thorough review from Oleg CLONE_PIDFD returns pidfds in the
parent_tidptr argument. This means we can give back the associated pid
and the pidfd at the same time. Access to process metadata information
thus becomes rather trivial.
As has been agreed, CLONE_PIDFD creates file descriptors based on
anonymous inodes similar to the new mount api. They are made
unconditional by this patchset as they are now needed by core kernel
code (vfs, pidfd) even more than they already were before (timerfd,
signalfd, io_uring, epoll etc.). The core patchset is rather small.
The bulky looking changelist is caused by David's very simple changes
to Kconfig to make anon inodes unconditional.
A pidfd comes with additional information in fdinfo if the kernel
supports procfs. The fdinfo file contains the pid of the process in
the callers pid namespace in the same format as the procfs status
file, i.e. "Pid:\t%d".
To remove worries about missing metadata access this patchset comes
with a sample/test program that illustrates how a combination of
CLONE_PIDFD and pidfd_send_signal() can be used to gain race-free
access to process metadata through /proc/<pid>.
Further work based on this patchset has been done by Joel. His work
makes pidfds pollable. It finished too late for this merge window. I
would prefer to have it sitting in linux-next for a while and send it
for inclusion during the 5.3 merge window"
* tag 'pidfd-v5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
samples: show race-free pidfd metadata access
signal: support CLONE_PIDFD with pidfd_send_signal
clone: add CLONE_PIDFD
Make anon_inodes unconditional
The strtonum awk function is a GNU extension and is not available with
all versions of awk. The link of bzImage fails with this error message:
>> awk: line 2: function or never defined
>> awk: line 2: function strtonum never defined
objcopy: --pad-to: bad number: arch/s390/boot/compressed/vmlinux
Drop the awk script and the --pad-to objcopy parameter it generated and
use a FILL pattern with an appropriate alignment in the linker script
for the arch/s390/boot/compressed/vmlinux file.
Fixes: f678068652 ("s390/boot: pad bzImage to 4K")
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull crypto update from Herbert Xu:
"API:
- Add support for AEAD in simd
- Add fuzz testing to testmgr
- Add panic_on_fail module parameter to testmgr
- Use per-CPU struct instead multiple variables in scompress
- Change verify API for akcipher
Algorithms:
- Convert x86 AEAD algorithms over to simd
- Forbid 2-key 3DES in FIPS mode
- Add EC-RDSA (GOST 34.10) algorithm
Drivers:
- Set output IV with ctr-aes in crypto4xx
- Set output IV in rockchip
- Fix potential length overflow with hashing in sun4i-ss
- Fix computation error with ctr in vmx
- Add SM4 protected keys support in ccree
- Remove long-broken mxc-scc driver
- Add rfc4106(gcm(aes)) cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (179 commits)
crypto: ccree - use a proper le32 type for le32 val
crypto: ccree - remove set but not used variable 'du_size'
crypto: ccree - Make cc_sec_disable static
crypto: ccree - fix spelling mistake "protedcted" -> "protected"
crypto: caam/qi2 - generate hash keys in-place
crypto: caam/qi2 - fix DMA mapping of stack memory
crypto: caam/qi2 - fix zero-length buffer DMA mapping
crypto: stm32/cryp - update to return iv_out
crypto: stm32/cryp - remove request mutex protection
crypto: stm32/cryp - add weak key check for DES
crypto: atmel - remove set but not used variable 'alg_name'
crypto: picoxcell - Use dev_get_drvdata()
crypto: crypto4xx - get rid of redundant using_sd variable
crypto: crypto4xx - use sync skcipher for fallback
crypto: crypto4xx - fix cfb and ofb "overran dst buffer" issues
crypto: crypto4xx - fix ctr-aes missing output IV
crypto: ecrdsa - select ASN1 and OID_REGISTRY for EC-RDSA
crypto: ux500 - use ccflags-y instead of CFLAGS_<basename>.o
crypto: ccree - handle tee fips error during power management resume
crypto: ccree - add function to handle cryptocell tee fips error
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
- Support for kernel address space layout randomization
- Add support for kernel image signature verification
- Convert s390 to the generic get_user_pages_fast code
- Convert s390 to the stack unwind API analog to x86
- Add support for CPU directed interrupts for PCI devices
- Provide support for MIO instructions to the PCI base layer, this
will allow the use of direct PCI mappings in user space code
- Add the basic KVM guest ultravisor interface for protected VMs
- Add AT_HWCAP bits for several new hardware capabilities
- Update the CPU measurement facility counter definitions to SVN 6
- Arnds cleanup patches for his quest to get LLVM compiles working
- A vfio-ccw update with bug fixes and support for halt and clear
- Improvements for the hardware TRNG code
- Another round of cleanup for the QDIO layer
- Numerous cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJc0CCEAAoJEDjwexyKj9rgjmkH/A3e2drvuP/hSF3xfCKTQFdx
/PoLHQVCqENB3HU3FA/ljoXuG6jMgwj61looqlxBNumXFpIfTg0E1JC5S4wRGJ+K
cOVhIKV53gcuZkRcCJQp0WMnGzpk1Daf7iYXYmAl+7e+mREUPxOuJ0Ei6vXvRGZS
8cQrUCGrtPgkAeLlndypHI2M2TDDGJIMczOGbOZau8+8Lo7Wq9zt5y0h/v0ew37g
ogA0eGh6koU1435dt2pclZRiZ1XOcar3Uin9ioT+RnSgJ4pr1Pza/F6IGO0RdQa+
rva990lqGFp5r9lE4rMCwK9LWb/rfHdVPd35t9XPwphnQ/ORoWUwLk3uc5XOHow=
=dbuy
-----END PGP SIGNATURE-----
Merge tag 's390-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- Support for kernel address space layout randomization
- Add support for kernel image signature verification
- Convert s390 to the generic get_user_pages_fast code
- Convert s390 to the stack unwind API analog to x86
- Add support for CPU directed interrupts for PCI devices
- Provide support for MIO instructions to the PCI base layer, this will
allow the use of direct PCI mappings in user space code
- Add the basic KVM guest ultravisor interface for protected VMs
- Add AT_HWCAP bits for several new hardware capabilities
- Update the CPU measurement facility counter definitions to SVN 6
- Arnds cleanup patches for his quest to get LLVM compiles working
- A vfio-ccw update with bug fixes and support for halt and clear
- Improvements for the hardware TRNG code
- Another round of cleanup for the QDIO layer
- Numerous cleanups and bug fixes
* tag 's390-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (98 commits)
s390/vdso: drop unnecessary cc-ldoption
s390: fix clang -Wpointer-sign warnigns in boot code
s390: drop CONFIG_VIRT_TO_BUS
s390: boot, purgatory: pass $(CLANG_FLAGS) where needed
s390: only build for new CPUs with clang
s390: simplify disabled_wait
s390/ftrace: use HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
s390/unwind: introduce stack unwind API
s390/opcodes: add missing instructions to the disassembler
s390/bug: add entry size to the __bug_table section
s390: use proper expoline sections for .dma code
s390/nospec: rename assembler generated expoline thunks
s390: add missing ENDPROC statements to assembler functions
locking/lockdep: check for freed initmem in static_obj()
s390/kernel: add support for kernel address space layout randomization (KASLR)
s390/kernel: introduce .dma sections
s390/sclp: do not use static sccbs
s390/kprobes: use static buffer for insn_page
s390/kernel: convert SYSCALL and PGM_CHECK handlers to .quad
s390/kernel: build a relocatable kernel
...
Pull locking updates from Ingo Molnar:
"Here are the locking changes in this cycle:
- rwsem unification and simpler micro-optimizations to prepare for
more intrusive (and more lucrative) scalability improvements in
v5.3 (Waiman Long)
- Lockdep irq state tracking flag usage cleanups (Frederic
Weisbecker)
- static key improvements (Jakub Kicinski, Peter Zijlstra)
- misc updates, cleanups and smaller fixes"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
locking/lockdep: Remove unnecessary unlikely()
locking/static_key: Don't take sleeping locks in __static_key_slow_dec_deferred()
locking/static_key: Factor out the fast path of static_key_slow_dec()
locking/static_key: Add support for deferred static branches
locking/lockdep: Test all incompatible scenarios at once in check_irq_usage()
locking/lockdep: Avoid bogus Clang warning
locking/lockdep: Generate LOCKF_ bit composites
locking/lockdep: Use expanded masks on find_usage_*() functions
locking/lockdep: Map remaining magic numbers to lock usage mask names
locking/lockdep: Move valid_state() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
locking/rwsem: Prevent unneeded warning during locking selftest
locking/rwsem: Optimize rwsem structure for uncontended lock acquisition
locking/rwsem: Enable lock event counting
locking/lock_events: Don't show pvqspinlock events on bare metal
locking/lock_events: Make lock_events available for all archs & other locks
locking/qspinlock_stat: Introduce generic lockevent_*() counting APIs
locking/rwsem: Enhance DEBUG_RWSEMS_WARN_ON() macro
locking/rwsem: Add debug check for __down_read*()
locking/rwsem: Micro-optimize rwsem_try_read_lock_unqueued()
locking/rwsem: Move rwsem internal function declarations to rwsem-xadd.h
...
Pull stack trace updates from Ingo Molnar:
"So Thomas looked at the stacktrace code recently and noticed a few
weirdnesses, and we all know how such stories of crummy kernel code
meeting German engineering perfection end: a 45-patch series to clean
it all up! :-)
Here's the changes in Thomas's words:
'Struct stack_trace is a sinkhole for input and output parameters
which is largely pointless for most usage sites. In fact if embedded
into other data structures it creates indirections and extra storage
overhead for no benefit.
Looking at all usage sites makes it clear that they just require an
interface which is based on a storage array. That array is either on
stack, global or embedded into some other data structure.
Some of the stack depot usage sites are outright wrong, but
fortunately the wrongness just causes more stack being used for
nothing and does not have functional impact.
Another oddity is the inconsistent termination of the stack trace
with ULONG_MAX. It's pointless as the number of entries is what
determines the length of the stored trace. In fact quite some call
sites remove the ULONG_MAX marker afterwards with or without nasty
comments about it. Not all architectures do that and those which do,
do it inconsistenly either conditional on nr_entries == 0 or
unconditionally.
The following series cleans that up by:
1) Removing the ULONG_MAX termination in the architecture code
2) Removing the ULONG_MAX fixups at the call sites
3) Providing plain storage array based interfaces for stacktrace
and stackdepot.
4) Cleaning up the mess at the callsites including some related
cleanups.
5) Removing the struct stack_trace based interfaces
This is not changing the struct stack_trace interfaces at the
architecture level, but it removes the exposure to the generic
code'"
* 'core-stacktrace-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
x86/stacktrace: Use common infrastructure
stacktrace: Provide common infrastructure
lib/stackdepot: Remove obsolete functions
stacktrace: Remove obsolete functions
livepatch: Simplify stack trace retrieval
tracing: Remove the last struct stack_trace usage
tracing: Simplify stack trace retrieval
tracing: Make ftrace_trace_userstack() static and conditional
tracing: Use percpu stack trace buffer more intelligently
tracing: Simplify stacktrace retrieval in histograms
lockdep: Simplify stack trace handling
lockdep: Remove save argument from check_prev_add()
lockdep: Remove unused trace argument from print_circular_bug()
drm: Simplify stacktrace handling
dm persistent data: Simplify stack trace handling
dm bufio: Simplify stack trace retrieval
btrfs: ref-verify: Simplify stack trace retrieval
dma/debug: Simplify stracktrace retrieval
fault-inject: Simplify stacktrace retrieval
mm/page_owner: Simplify stack trace handling
...
Pull speculation mitigation update from Ingo Molnar:
"This adds the "mitigations=" bootline option, which offers a
cross-arch set of options that will work on x86, PowerPC and s390 that
will map to the arch specific option internally"
* 'core-speculation-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
s390/speculation: Support 'mitigations=' cmdline option
powerpc/speculation: Support 'mitigations=' cmdline option
x86/speculation: Support 'mitigations=' cmdline option
cpu/speculation: Add 'mitigations=' cmdline option
Pull unified TLB flushing from Ingo Molnar:
"This contains the generic mmu_gather feature from Peter Zijlstra,
which is an all-arch unification of TLB flushing APIs, via the
following (broad) steps:
- enhance the <asm-generic/tlb.h> APIs to cover more arch details
- convert most TLB flushing arch implementations to the generic
<asm-generic/tlb.h> APIs.
- remove leftovers of per arch implementations
After this series every single architecture makes use of the unified
TLB flushing APIs"
* 'core-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm/resource: Use resource_overlaps() to simplify region_intersects()
ia64/tlb: Eradicate tlb_migrate_finish() callback
asm-generic/tlb: Remove tlb_table_flush()
asm-generic/tlb: Remove tlb_flush_mmu_free()
asm-generic/tlb: Remove CONFIG_HAVE_GENERIC_MMU_GATHER
asm-generic/tlb: Remove arch_tlb*_mmu()
s390/tlb: Convert to generic mmu_gather
asm-generic/tlb: Introduce CONFIG_HAVE_MMU_GATHER_NO_GATHER=y
arch/tlb: Clean up simple architectures
um/tlb: Convert to generic mmu_gather
sh/tlb: Convert SH to generic mmu_gather
ia64/tlb: Convert to generic mmu_gather
arm/tlb: Convert to generic mmu_gather
asm-generic/tlb, arch: Invert CONFIG_HAVE_RCU_TABLE_INVALIDATE
asm-generic/tlb, ia64: Conditionally provide tlb_migrate_finish()
asm-generic/tlb: Provide generic tlb_flush() based on flush_tlb_mm()
asm-generic/tlb, arch: Provide generic tlb_flush() based on flush_tlb_range()
asm-generic/tlb, arch: Provide generic VIPT cache flush
asm-generic/tlb, arch: Provide CONFIG_HAVE_MMU_GATHER_PAGE_SIZE
asm-generic/tlb: Provide a comment
Towards the goal of removing cc-ldoption, it seems that --hash-style=
was added to binutils 2.17.50.0.2 in 2006. The minimal required version
of binutils for the kernel according to
Documentation/process/changes.rst is 2.20.
Link: https://gcc.gnu.org/ml/gcc/2007-01/msg01141.html
Cc: clang-built-linux@googlegroups.com
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The arch/s390/boot directory is built with its own set of compiler
options that does not include -Wno-pointer-sign like the rest of
the kernel does, this causes a lot of harmless but correct warnings
when building with clang.
For the atomics, we can add type casts to avoid the warnings, for
everything else the easiest way is to slightly adapt the types
to be more consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
VIRT_TO_BUS is only used for legacy device PCI and ISA drivers using
virt_to_bus() instead of the streaming DMA mapping API, and the
remaining drivers generally don't work on 64-bit architectures.
Two of these drivers also cause a build warning on s390, so instead
of trying to fix that, let's just disable the option as we do on
most architectures now.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The purgatory and boot Makefiles do not inherit the original cflags,
so clang falls back to the default target architecture when building it,
typically this would be x86 when cross-compiling.
Add $(CLANG_FLAGS) everywhere so we pass the correct --target=s390x-linux
option when cross-compiling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
llvm does does not understand -march=z9-109 and older target
specifiers, so disable the respective Kconfig settings and
the logic to make the boot code work on old systems when
building with clang.
Part of the early boot code is normally compiled with -march=z900
for maximum compatibility. This also has to get changed with
clang to the oldest supported ISA, which is -march=z10 here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The disabled_wait() function uses its argument as the PSW address when
it stops the CPU with a wait PSW that is disabled for interrupts.
The different callers sometimes use a specific number like 0xdeadbeef
to indicate a specific failure, the early boot code uses 0 and some
other calls sites use __builtin_return_address(0).
At the time a dump is created the current PSW and the registers of a
CPU are written to lowcore to make them avaiable to the dump analysis
tool. For a CPU stopped with disabled_wait the PSW and the registers
do not really make sense together, the PSW address does not point to
the function the registers belong to.
Simplify disabled_wait() by using _THIS_IP_ for the PSW address and
drop the argument to the function.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the call chain more reliable by tagging the ftrace stack entries
with the stack pointer that is associated with the return address.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rework the dump_trace() stack unwinder interface to support different
unwinding algorithms. The new interface looks like this:
struct unwind_state state;
unwind_for_each_frame(&state, task, regs, start_stack)
do_something(state.sp, state.ip, state.reliable);
The unwind_bc.c file contains the implementation for the classic
back-chain unwinder.
One positive side effect of the new code is it now handles ftraced
functions gracefully. It prints the real name of the return function
instead of 'return_to_handler'.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the __EMIT_BUG inline assembly to emit mergeable __bug_table
entries with type @progbits and specify the size of each entry.
The entry size is encoded sh_entsize field of the section definition,
it allows to identify which struct bug_entry to use to decode the
entries. This will be needed for the objtool support.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The text_dma.S code uses its own macro to generate an inline version of an
expoline. To make it easier to identify all expolines in the kernel use a
thunk and a branch to the thunk just like the rest of the kernel code does
it.
The name of the text_dma.S expoline thunk is __dma__s390_indirect_jump_r14
and the section is named .dma.text.__s390_indirect_jump_r14.
This will be needed for the objtool support.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The assembler version of the expoline thunk use the naming
__s390x_indirect_jump_rxuse_ry while the compiler generates names
like __s390_indirect_jump_rx_use_ry. Make the naming more consistent.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The assembler code in arch/s390 misses proper ENDPROC statements
to properly end functions in a few places. Add them.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- VSIE crypto fixes
- new guest features for gen15
- disable halt polling for nested virtualization with overcommit
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=mZyZ
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Features and fixes for 5.2
- VSIE crypto fixes
- new guest features for gen15
- disable halt polling for nested virtualization with overcommit
The following warning occurred on s390:
WARNING: CPU: 0 PID: 804 at kernel/locking/lockdep.c:1025 lockdep_register_key+0x30/0x150
This is because the check in static_obj() assumes that all memory within
[_stext, _end] belongs to static objects, which at least for s390 isn't
true. The init section is also part of this range, and freeing it allows
the buddy allocator to allocate memory from it. We have virt == phys for
the kernel on s390, so that such allocations would then have addresses
within the range [_stext, _end].
To fix this, introduce arch_is_kernel_initmem_freed(), similar to
arch_is_kernel_text/data(), and add it to the checks in static_obj().
This will always return 0 on architectures that do not define
arch_is_kernel_initmem_freed. On s390, it will return 1 if initmem has
been freed and the address is in the range [__init_begin, __init_end].
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for relocating the kernel to a random address.
The random kernel offset is obtained from cpacf, using either TRNG, PRNO,
or KMC_PRNG, depending on supported MSA level.
KERNELOFFSET is added to vmcoreinfo, for crash --kaslr support.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With a relocatable kernel that could reside at any place in memory, code
and data that has to stay below 2 GB needs special handling.
This patch introduces .dma sections for such text, data and ex_table.
The sections will be part of the decompressor kernel, so they will not
be relocated and stay below 2 GB. Their location is passed over to the
decompressed / relocated kernel via the .boot.preserved.data section.
The duald and aste for control register setup also need to stay below
2 GB, so move the setup code from arch/s390/kernel/head64.S to
arch/s390/boot/head.S. The duct and linkage_stack could reside above
2 GB, but their content has to be preserved for the decompresed kernel,
so they are also moved into the .dma section.
The start and end address of the .dma sections is added to vmcoreinfo,
for crash support, to help debugging in case the kernel crashed there.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sccbs for init/read/sdias/early have to be located below 2 GB, and
they are currently defined as a static buffer.
With a relocatable kernel that could reside at any place in memory, this
will no longer guarantee the location below 2 GB, so use a dynamic
GFP_DMA allocation instead.
The sclp_early_sccb buffer needs special handling, as it can be used
very early, and by both the decompressor and also the decompressed
kernel. Therefore, a fixed 4 KB buffer is introduced at 0x11000, the
former PARMAREA_END. The new PARMAREA_END is now 0x12000, and it is
renamed to HEAD_END, as it is rather the end of head.S and not the end
of the parmarea.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With a relocatable kernel that could reside at any place in memory, the
current logic for allocating a kprobes insn_page does not work. The
GFP_DMA allocated buffer might be more than 2 GB away from the kernel.
Use a static buffer for the insn_page instead.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With a relocatable kernel that could reside at any place in memory, the
storage size for the SYSCALL and PGM_CHECK handlers needs to be
increased from .long to .quad.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for building a relocatable kernel with -fPIE.
The kernel will be relocated to 0 early in the boot process.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow for userspace to use PCI MIO instructions.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow users to disable usage of MIO instructions by specifying pci=nomio
at the kernel command line.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide support for PCI I/O instructions that work on mapped IO addresses.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is a preparation patch for usage of new pci instructions.
No functional change.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide a kernel parameter to force the usage of floating interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Gather statistics to distinguish floating and directed interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve /proc/interrupts on s390 to show statistics for individual
MSI interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Up until now all interrupts on s390 have been floating. For MSI interrupts
we've used a global summary bit vector (with a bit for each function) and
a per-function interrupt bit vector (with a bit per MSI).
This patch introduces a new IRQ delivery mode: CPU directed interrupts.
In this new mode a per-CPU interrupt bit vector is used (with a bit per
MSI per function). Further it is now possible to direct an IRQ to a
specific CPU so we can finally support IRQ affinity.
If an interrupt can't be delivered because the appointed CPU is occupied
by a hypervisor the interrupt is delivered floating. For this a global
summary bit vector is used (with a bit per CPU).
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide the ability to create cachesize aligned interrupt vectors.
These will be used for per-CPU interrupt vectors.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename and clarify the usage of the interrupt bit vectors. Also change
the array of the per-function bit vectors to be dynamically allocated.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add an extra parameter for airq handlers to recognize
floating vs. directed interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Detect the adapter CPU directed interruption facility.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move everything interrupt related from pci.c to pci_irq.c.
No functional change.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide an interface for userspace so it can find out if a machine is
capeable of doing secure boot. The interface is, for example, needed for
zipl so it can find out which file format it can/should write to disk.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A kernel loaded via kexec_load cannot be verified. Thus disable kexec_load
systemcall in kernels which where IPLed securely. Use the IMA mechanism to
do so.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add kernel signature verification to kexec_file. The verification is based
on module signature verification and works with kernel images signed via
scripts/sign-file.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The leading 64 kB of a kernel image doesn't contain any data needed to boot
the new kernel when it was loaded via kexec_file. Thus kexec_file currently
strips them off before loading the image. Keep the leading 64 kB in order
to be able to pass a ipl_report to the next kernel.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390_image_load and s390_elf_load have the same code to load the different
components. Combine this functionality in one shared function.
While at it move kexec_file_update_kernel into the new function as well.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Access the parmarea in head.S via a struct instead of individual offsets.
While at it make the fields in the parmarea .quads.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Omit use of script/bin2c hack. Directly include into assembler file instead.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The purgatory is compiled into the vmlinux and keept in memory all the time
during runtime. Thus any section not needed to load the purgatory
unnecessarily bloats up its foot print in file- and memorysize. Reduce the
purgatory size by stripping the unneeded sections from the purgatory.
This reduces the purgatories size by ~33%.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To register data for the next kernel (command line, oldmem_base, etc.) the
current kernel needs to find the ELF segment that contains head.S. This is
currently done by checking ifor 'phdr->p_paddr == 0'. This works fine for
the current kernel build but in theory the first few pages could be
skipped. Make the detection more robust by checking if the entry point lies
within the segment.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When loading an ELF image via kexec_file the segment alignment is ignored
in the calculation for the load address of the next segment. When there are
multiple segments this can lead to segment overlap and thus load failure.
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Fixes: 8be0188271 ("s390/kexec_file: Add ELF loader")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the guest do not have AP instructions nor Key management
we should return without shadowing the CRYCB.
We did not check correctly in the past.
Fixes: b10bd9a256 ("s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity")
Fixes: 6ee7409820 ("KVM: s390: vsie: allow CRYCB FORMAT-0")
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1556269010-22258-1-git-send-email-pmorel@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In order to be able to sign the bzImage independent of the block size
of the IPL device, align the bzImage to 4096 bytes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
PR: Adjusted to the use in kexec_file later.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read the IPL Report block provided by secure-boot, add the entries
of the certificate list to the system key ring and print the list
of components.
PR: Adjust to Vasilys bootdata_preserved patch set. Preserve ipl_cert_list
for later use in kexec_file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To transport the information required for secure boot a new IPL report
will be created at boot time. It will be written to memory right after
the IPL parameter block. To work with the IPL report a couple of
additional structure definitions are added the the uapi/ipl.h header.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The IPL parameter block is used as an interface between Linux and
the machine to query and change the boot device and boot options.
To be able to create IPL parameter block in user space and pass it
as segment to kexec provide an uapi header with proper structure
definitions for the block.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ipl_info union in struct ipl_parameter_block has the same name as
the struct ipl_info. This does not help while reading the code and the
union in struct ipl_parameter_block does not need to be named. Drop
the name from the union.
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We do track the current steal time of the host CPUs. Let us use
this value to disable halt polling if the steal time goes beyond
a configured value.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
With the z14 machine there came also a CPACF hardware extension
which provides a True Random Number Generator. This TRNG can
be accessed with a new subfunction code within the CPACF prno
instruction and provides random data with very high entropy.
So if there is a TRNG available, let's use it for initial seeding
and reseeding instead of the current implementation which tries
to generate entropy based on stckf (store clock fast) jitters.
For details about the amount of data needed and pulled for
seeding and reseeding there can be explaining comments in the
code found.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Here is a rework of the generate_entropy function of the pseudo random
device driver exploiting the prno CPACF instruction.
George Spelvin pointed out some issues with the existing
implementation. One point was, that the buffer used to store the stckf
values is 2 pages which are initially filled with get_random_bytes()
for each 64 byte junk produced by the function. Another point was that
the stckf values only carry entropy in the LSB and thus a buffer of
2 pages is not really needed. Then there was a comment about the use
of the kimd cpacf function without proper initialization.
The rework addresses these points and now one page is used and only
one half of this is filled with get_random_bytes() on each chunk of 64
bytes requested data. The other half of the page is filled with stckf
values exored into with an overlap of 4 bytes. This can be done due to
the fact that only the lower 4 bytes carry entropy we need. For more
details about the algorithm used, see the header of the function.
The generate_entropy() function now uses the cpacf function klmd with
proper initialization of the parameter block to perform the sha512
hash.
George also pointed out some issues with the internal buffers used for
seeding and reads. These buffers are now zeroed with memzero_implicit
after use.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: George Spelvin <lkml@sdf.org>
Suggested-by: George Spelvin <lkml@sdf.org>
Reviewed-by: Patrick Steuer <steuer@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Instead of adding a new machine option to disable/enable the keywrapping
options of pckmo (like for AES and DEA) we can now use the CPU model to
decide. As ECC is also wrapped with the AES key we need that to be
enabled.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
This enables stfle.151 and adds the subfunctions for DFLTCC. Bit 151 is
added to the list of facilities that will be enabled when there is no
cpu model involved as DFLTCC requires no additional handling from
userspace, e.g. for migration.
Please note that a cpu model enabled user space can and will have the
final decision on the facility bits for a guests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
With git commit d1874a0c28
"s390/mm: make the pxd_offset functions more robust" and a 2-level page
table it can now happen that pgd_bad() gets asked to verify a large
segment table entry. If the entry is marked as dirty pgd_bad() will
incorrectly return true.
Change the pgd_bad(), p4d_bad(), pud_bad() and pmd_bad() functions to
first verify the table type, return false if the table level is lower
than what the function is suppossed to check, return true if the table
level is too high, and otherwise check the relevant region and segment
table bits. pmd_bad() has to check against ~SEGMENT_ENTRY_BITS for
normal page table pointers or ~SEGMENT_ENTRY_BITS_LARGE for large
segment table entries. Same for pud_bad() which has to check against
~_REGION_ENTRY_BITS or ~_REGION_ENTRY_BITS_LARGE.
Fixes: d1874a0c28 ("s390/mm: make the pxd_offset functions more robust")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch/s390/lib/uaccess.c is built without kasan instrumentation. Kasan
checks are performed explicitly in copy_from_user/copy_to_user
functions. But since those functions could be inlined, calls from
files like uaccess.c with instrumentation disabled won't generate
kasan reports. This is currently the case with strncpy_from_user
function which was revealed by newly added kasan test. Avoid inlining of
copy_from_user/copy_to_user when the kernel is built with kasan support
to make sure kasan checks are fully functional.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in
the release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they
are in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Y7Kd
-----END PGP SIGNATURE-----
Merge tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull syscall numbering updates from Arnd Bergmann:
"arch: add pidfd and io_uring syscalls everywhere
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in the
release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they are
in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call"
* tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: add pidfd and io_uring syscalls everywhere
A few architectures use <asm/segment.h> internally, but nothing in
common code does. Remove all the empty or almost empty versions of it,
including the asm-generic one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for the CPU-Measurement Facility counter
second version number 6. This number is used to detect some
more counters in the crypto counter set and the extended
counter set.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define the gup_fast_permitted to check against the asce_limit of the
mm attached to the current task, then replace the s390 specific gup
code with the generic implementation in mm/gup.c.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the way how pgd_offset, p4d_offset, pud_offset and pmd_offset
walk the page tables. pgd_offset now always calculates the index for
the top-level page table and adds it to the pgd, this is either a
segment table offset for a 2-level setup, a region-3 offset for 3-levels,
region-2 offset for 4-levels, or a region-1 offset for a 5-level setup.
The other three functions p4d_offset, pud_offset and pmd_offset will
only add the respective offset if they dereference the passed pointer.
With the new way of walking the page tables a sequence like this from
mm/gup.c now works:
pgdp = pgd_offset(current->mm, addr);
pgd = READ_ONCE(*pgdp);
p4dp = p4d_offset(&pgd, addr);
p4d = READ_ONCE(*p4dp);
pudp = pud_offset(&p4d, addr);
pud = READ_ONCE(*pudp);
pmdp = pmd_offset(&pud, addr);
pmd = READ_ONCE(*pmdp);
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the anon_inodes facility unconditional so that it can be used by core
VFS code and pidfd code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[christian@brauner.io: adapt commit message to mention pidfds]
Signed-off-by: Christian Brauner <christian@brauner.io>
- Fix overwrite of the initial ramdisk due to misuse of IS_ENABLED
- Fix integer overflow in the dasd driver resulting in incorrect number
of blocks for large devices
- Fix a lockdep false positive in the 3270 driver
- Fix a deadlock in the zcrypt driver
- Fix incorrect debug feature entries in the pkey api
- Fix inline assembly constraints fallout with CONFIG_KASAN=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcuIwlAAoJEDjwexyKj9rgCJEH/Agbx2sJlxApuKC6BMAjPZCy
dJUu7hmumgtL+QI7IqQMRgfuxiC16xpJQd14GvfNoyjX1NVajepYI2+OUZHj7F6s
La0fq/16fRriVByLiL+pqjV2y0c5kQ8Uhe15vwEvSmr3T/NgPLqUbIe5pwY5KS59
O6B3WpVKeIb8UOUlEAQnezTYj70jWMT783NTyzhPcYLkiN7JJ7vI21FKPRM88ElS
Q7f9qxGPv0hGsOqBXCBWztxgx+ezEHsnlH4t+he0tLOGXuuiy4BrgGtgbJx17frj
xNNe8gOXV83bUbYTBygITnjMjS0m/1viJ4XTBgv/HLGgcKG06n3v6U4+zefB4N4=
=+41g
-----END PGP SIGNATURE-----
Merge tag 's390-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 bug fixes from Martin Schwidefsky:
- Fix overwrite of the initial ramdisk due to misuse of IS_ENABLED
- Fix integer overflow in the dasd driver resulting in incorrect number
of blocks for large devices
- Fix a lockdep false positive in the 3270 driver
- Fix a deadlock in the zcrypt driver
- Fix incorrect debug feature entries in the pkey api
- Fix inline assembly constraints fallout with CONFIG_KASAN=y
* tag 's390-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: correct some inline assembly constraints
s390/pkey: add one more argument space for debug feature entry
s390/zcrypt: fix possible deadlock situation on ap queue remove
s390/3270: fix lockdep false positive on view->lock
s390/dasd: Fix capacity calculation for large volumes
s390/mem_detect: Use IS_ENABLED(CONFIG_BLK_DEV_INITRD)
This enables stfle.150 and adds the subfunctions for SORTL. Bit 150 is
added to the list of facilities that will be enabled when there is no
cpu model involved as sortl requires no additional handling from
userspace, e.g. for migration.
Please note that a cpu model enabled user space can and will have the
final decision on the facility bits for a guests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Some of the new features have a 32byte response for the query function.
Provide a new wrapper similar to __cpacf_query. We might want to factor
this out if other users come up, as of today there is none. So let us
keep the function within KVM.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
This enables stfle.155 and adds the subfunctions for KDSA. Bit 155 is
added to the list of facilities that will be enabled when there is no
cpu model involved as MSA9 requires no additional handling from
userspace, e.g. for migration.
Please note that a cpu model enabled user space can and will have the
final decision on the facility bits for a guests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
If vector support is enabled, the vector BCD enhancements facility
might also be enabled.
We can directly forward this facility to the guest if available
and VX is requested by user space.
Please note that user space can and will have the final decision
on the facility bits for a guests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
If vector support is enabled, the vector enhancements facility 2
might also be enabled.
We can directly forward this facility to the guest if available
and VX is requested by user space.
Please note that user space can and will have the final decision
on the facility bits for a guests.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Inline assembly code changed in this patch should really use "Q"
constraint "Memory reference without index register and with short
displacement". The kernel build with kasan instrumentation enabled
might occasionally break otherwise (due to stack instrumentation).
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All architectures except MIPS were defining it in the same way,
and memory slots are handled entirely by common code so there
is no point in keeping the definition per-architecture.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the io_uring and pidfd_send_signal system calls to all architectures.
These system calls are designed to handle both native and compat tasks,
so all entries are the same across architectures, only arm-compat and
the generic tale still use an old format.
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> (s390)
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Terminating the last trace entry with ULONG_MAX is a completely pointless
exercise and none of the consumers can rely on it because it's
inconsistently implemented across architectures. In fact quite some of the
callers remove the entry and adjust stack_trace.nr_entries afterwards.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Link: https://lkml.kernel.org/r/20190410103644.396788431@linutronix.de
llvm on s390 has problems with __builtin_return_address(n), with n>0,
this results in a somewhat cryptic error message:
fatal error: error in backend: Unsupported stack frame traversal count
To work around it, use the direct return address directly. This
is probably not ideal here, but gets things to compile and should
only lead to inferior reporting, not to misbehavior of the generated
code.
Link: https://bugs.llvm.org/show_bug.cgi?id=41424
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
IS_ENABLED should be reserved for CONFIG_<FOO> uses so convert
the uses of IS_ENABLED with a #define to __is_defined.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
llvm skips an empty .bss section entirely, which makes
the check fail with an unexpected error:
/tmp/binutils-multi-test/bin/s390x-linux-gnu-objdump: section '.bss' mentioned in a -j option, but not found in any input file
error: arch/s390/boot/compressed/decompressor.o .bss section is not empty
../arch/s390/scripts/Makefile.chkbss:20: recipe for target 'arch/s390/boot/compressed/decompressor.o.chkbss' failed
Change the check so we first see if a .bss section exists
before trying to read its size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
clang fails to use the %O and %R inline assembly modifiers
the same way as gcc, leading to build failures with every use
of __load_psw_mask():
/tmp/nmi-4a9f80.s: Assembler messages:
/tmp/nmi-4a9f80.s:571: Error: junk at end of line: `+8(160(%r11))'
/tmp/nmi-4a9f80.s:626: Error: junk at end of line: `+8(160(%r11))'
Replace these with a more conventional way of passing the addresses
that should work with both clang and gcc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Building system calls with clang results in a warning
about an alias from a global function to a static one:
../fs/namei.c:3847:1: warning: unused function '__se_sys_mkdirat' [-Wunused-function]
SYSCALL_DEFINE3(mkdirat, int, dfd, const char __user *, pathname, umode_t, mode)
^
../include/linux/syscalls.h:219:36: note: expanded from macro 'SYSCALL_DEFINE3'
#define SYSCALL_DEFINE3(name, ...) SYSCALL_DEFINEx(3, _##name, __VA_ARGS__)
^
../include/linux/syscalls.h:228:2: note: expanded from macro 'SYSCALL_DEFINEx'
__SYSCALL_DEFINEx(x, sname, __VA_ARGS__)
^
../arch/s390/include/asm/syscall_wrapper.h:126:18: note: expanded from macro '__SYSCALL_DEFINEx'
asmlinkage long __se_sys##name(__MAP(x,__SC_LONG,__VA_ARGS__)) \
^
<scratch space>:31:1: note: expanded from here
__se_sys_mkdirat
^
The only reference to the static __se_sys_mkdirat() here is the alias, but
this only gets evaluated later. Making this function global as well avoids
the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
clang does not support 31 bit object files on s390, so skip
the 32-bit vdso here, and only build it when using gcc to compile
the kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This was added as a workaround for really old compilers, and it prevents
building with clang now. I can see no reason for keeping it, as it has
already been removed for most architectures in the pre-git era, so
let's remove it everywhere, rather than only for clang.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The CALL_ON_STACK helper currently does not work with clang and for
calls without arguments. It does not initialize r2 although the constraint
is "+&d". Rework the CALL_FMT_x and the CALL_ON_STACK macros to work
with clang and produce optimal code in all cases.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If CONFIG_PGSTE is not set (e.g. when compiling without KVM), GCC complains:
CC arch/s390/mm/pgtable.o
arch/s390/mm/pgtable.c:413:15: warning: ‘pmd_alloc_map’ defined but not
used [-Wunused-function]
static pmd_t *pmd_alloc_map(struct mm_struct *mm, unsigned long addr)
^~~~~~~~~~~~~
Wrap the function with "#ifdef CONFIG_PGSTE" to silence the warning.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Disallow kernel command line alteration via ipl parameter block if
running in protected virtualization environment.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The Ultravisor Call Facility (stfle bit 158) defines an API to the
Ultravisor (UV calls), a mini hypervisor located at machine
level. With help of the Ultravisor, KVM will be able to run
"protected" VMs, special VMs whose memory and management data are
unavailable to KVM.
The protected VMs can also request services from the Ultravisor.
The guest api consists of UV calls to share and unshare memory with the
kvm hypervisor.
To enable this feature support PROTECTED_VIRTUALIZATION_GUEST kconfig
option has been introduced.
Co-developed-by: Janosch Frank <frankja@de.ibm.com>
Signed-off-by: Janosch Frank <frankja@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same as for .boot.data section make sure that .boot.preserved.data
sections of vmlinux and arch/s390/compressed/vmlinux match before
producing the compressed kernel image. Symbols presence, order and sizes
are cross-checked.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
.boot.preserved.data is a better fit for ipl block than .boot.data
which is discarded after init. Reusing .boot.preserved.data allows to
simplify code a little bit and avoid copying data from .boot.data to
persistent variables.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce .boot.preserve.data section which is similar to .boot.data and
"shared" between the decompressor code and the decompressed kernel. The
decompressor will store values in it, and copy over to the decompressed
image before starting it. This method allows to avoid using pre-defined
addresses and other hacks to pass values between those boot phases.
Unlike .boot.data section .boot.preserved.data is NOT a part of init data,
and hence will be preserved for the kernel life time.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Hook up asm-generic/mmiowb.h to Kbuild for all architectures so that we
can subsequently include asm/mmiowb.h from core code.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, we have two different implementation of rwsem:
1) CONFIG_RWSEM_GENERIC_SPINLOCK (rwsem-spinlock.c)
2) CONFIG_RWSEM_XCHGADD_ALGORITHM (rwsem-xadd.c)
As we are going to use a single generic implementation for rwsem-xadd.c
and no architecture-specific code will be needed, there is no point
in keeping two different implementations of rwsem. In most cases, the
performance of rwsem-spinlock.c will be worse. It also doesn't get all
the performance tuning and optimizations that had been implemented in
rwsem-xadd.c over the years.
For simplication, we are going to remove rwsem-spinlock.c and make all
architectures use a single implementation of rwsem - rwsem-xadd.c.
All references to RWSEM_GENERIC_SPINLOCK and RWSEM_XCHGADD_ALGORITHM
in the code are removed.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-um@lists.infradead.org
Cc: linux-xtensa@linux-xtensa.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: nios2-dev@lists.rocketboards.org
Cc: openrisc@lists.librecores.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Link: https://lkml.kernel.org/r/20190322143008.21313-3-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As the generic rwsem-xadd code is using the appropriate acquire and
release versions of the atomic operations, the arch specific rwsem.h
files will not be that much faster than the generic code as long as the
atomic functions are properly implemented. So we can remove those arch
specific rwsem.h and stop building asm/rwsem.h to reduce maintenance
effort.
Currently, only x86, alpha and ia64 have implemented architecture
specific fast paths. I don't have access to alpha and ia64 systems for
testing, but they are legacy systems that are not likely to be updated
to the latest kernel anyway.
By using a rwsem microbenchmark, the total locking rates on a 4-socket
56-core 112-thread x86-64 system before and after the patch were as
follows (mixed means equal # of read and write locks):
Before Patch After Patch
# of Threads wlock rlock mixed wlock rlock mixed
------------ ----- ----- ----- ----- ----- -----
1 29,201 30,143 29,458 28,615 30,172 29,201
2 6,807 13,299 1,171 7,725 15,025 1,804
4 6,504 12,755 1,520 7,127 14,286 1,345
8 6,762 13,412 764 6,826 13,652 726
16 6,693 15,408 662 6,599 15,938 626
32 6,145 15,286 496 5,549 15,487 511
64 5,812 15,495 60 5,858 15,572 60
There were some run-to-run variations for the multi-thread tests. For
x86-64, using the generic C code fast path seems to be a little bit
faster than the assembly version with low lock contention. Looking at
the assembly version of the fast paths, there are assembly to/from C
code wrappers that save and restore all the callee-clobbered registers
(7 registers on x86-64). The assembly generated from the generic C
code doesn't need to do that. That may explain the slight performance
gain here.
The generic asm rwsem.h can also be merged into kernel/locking/rwsem.h
with no code change as no other code other than those under
kernel/locking needs to access the internal rwsem macros and functions.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-um@lists.infradead.org
Cc: linux-xtensa@linux-xtensa.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: nios2-dev@lists.rocketboards.org
Cc: openrisc@lists.librecores.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Link: https://lkml.kernel.org/r/20190322143008.21313-2-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move the mmu_gather::page_size things into the generic code instead of
PowerPC specific bits.
No change in behavior intended.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nick Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support for the CPU-Measurement Facility counter
second version number 6. This number is used to detect some
more counters in the crypto counter set and the extended
counter set.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
IS_ENABLED should generally use CONFIG_ prefaced symbols and
it doesn't appear as if there is a BLK_DEV_INITRD define.
Cc: <stable@vger.kernel.org> # 4.20
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- Fix early free of the channel program in vfio
- On AP device removal make sure that all messages are flushed
with the driver still attached that queued the message
- Limit brk randomization to 32MB to reduce the chance that the
heap of ld.so is placed after the main stack
- Add a rolling average for the steal time of a CPU, this will be
needed for KVM to decide when to do busy waiting
- Fix a warning in the CPU-MF code
- Add a notification handler for AP configuration change to react
faster to new AP devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcnIq7AAoJEDjwexyKj9rgddUH/3VQP6BMvq2fwAsLqx8JeYgT
082xzP2nHli3tO6m8fFHmtqrSg5KTEDfuQVafqp92LeEMKUNWQI6kRu7rXeAVBct
M6hx21mqkm9VNjAlAjSq8IAUXP2K6/K0BMD5mYInYYYVRvJm3on4sHnkEj0kvXbm
OGxwnNBd9UnH5g6ti2vW4cyDvs0aqj1eDbSudy5KedumQz5J2XdFPn4f4Ej6p2+t
nuvlZFDnZ2Z4rliE3RFCuKExZR+YFZgS1urm6pcklncfvbJRsqFJ+nvhurskDUI3
4gOp1Yv1tvGNv/cNVEtnz8g/Kg8/sI7evjQBtxhtEsV/W0sbZPnjCt+28Cf1DN4=
=4nL7
-----END PGP SIGNATURE-----
Merge tag 's390-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Improvements and bug fixes for 5.1-rc2:
- Fix early free of the channel program in vfio
- On AP device removal make sure that all messages are flushed with
the driver still attached that queued the message
- Limit brk randomization to 32MB to reduce the chance that the heap
of ld.so is placed after the main stack
- Add a rolling average for the steal time of a CPU, this will be
needed for KVM to decide when to do busy waiting
- Fix a warning in the CPU-MF code
- Add a notification handler for AP configuration change to react
faster to new AP devices"
* tag 's390-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cpumf: Fix warning from check_processor_id
zcrypt: handle AP Info notification from CHSC SEI command
vfio: ccw: only free cp on final interrupt
s390/vtime: steal time exponential moving average
s390/zcrypt: revisit ap device remove procedure
s390: limit brk randomization to 32MB
Function __hw_perf_event_init() used a CPU variable without
ensuring CPU preemption has been disabled. This caused the
following warning in the kernel log:
[ 7.277085] BUG: using smp_processor_id() in preemptible
[00000000] code: cf-csdiag/1892
[ 7.277111] caller is cf_diag_event_init+0x13a/0x338
[ 7.277122] CPU: 10 PID: 1892 Comm: cf-csdiag Not tainted
5.0.0-20190318.rc0.git0.9e1a11e0f602.300.fc29.s390x+debug #1
[ 7.277131] Hardware name: IBM 2964 NC9 712 (LPAR)
[ 7.277139] Call Trace:
[ 7.277150] ([<000000000011385a>] show_stack+0x82/0xd0)
[ 7.277161] [<0000000000b7a71a>] dump_stack+0x92/0xd0
[ 7.277174] [<00000000007b7e9c>] check_preemption_disabled+0xe4/0x100
[ 7.277183] [<00000000001228aa>] cf_diag_event_init+0x13a/0x338
[ 7.277195] [<00000000002cf3aa>] perf_try_init_event+0x72/0xf0
[ 7.277204] [<00000000002d0bba>] perf_event_alloc+0x6fa/0xce0
[ 7.277214] [<00000000002dc4a8>] __s390x_sys_perf_event_open+0x398/0xd50
[ 7.277224] [<0000000000b9e8f0>] system_call+0xdc/0x2d8
[ 7.277233] 2 locks held by cf-csdiag/1892:
[ 7.277241] #0: 00000000976f5510 (&sig->cred_guard_mutex){+.+.},
at: __s390x_sys_perf_event_open+0xd2e/0xd50
[ 7.277257] #1: 00000000363b11bd (&pmus_srcu){....},
at: perf_event_alloc+0x52e/0xce0
The variable is now accessed in proper context. Use
get_cpu_var()/put_cpu_var() pair to disable
preemption during access.
As the hardware authorization settings apply to all CPUs, it
does not matter which CPU is used to check the authorization setting.
Remove the event->count assignment. It is not needed as function
perf_event_alloc() allocates memory for the event with kzalloc() and
thus count is already set to zero.
Fixes: fe5908bccc ("s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently, every arch/*/include/uapi/asm/Kbuild explicitly includes
the common Kbuild.asm file. Factor out the duplicated include directives
to scripts/Makefile.asm-generic so that no architecture would opt out
of the mandatory-y mechanism.
um is not forced to include mandatory-y since it is a very exceptional
case which does not support UAPI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The generic-y is redundant under the following condition:
- arch has its own implementation
- the same header is added to generated-y
- the same header is added to mandatory-y
If a redundant generic-y is found, the warning like follows is displayed:
scripts/Makefile.asm-generic:20: redundant generic-y found in arch/arm/include/asm/Kbuild: timex.h
I fixed up arch Kbuild files found by this.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
for 32-bit guests
s390: interrupt cleanup, introduction of the Guest Information Block,
preparation for processor subfunctions in cpu models
PPC: bug fixes and improvements, especially related to machine checks
and protection keys
x86: many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations; plus AVIC fixes.
Generic: memcg accounting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJci+7XAAoJEL/70l94x66DUMkIAKvEefhceySHYiTpfefjLjIC
16RewgHa+9CO4Oo5iXiWd90fKxtXLXmxDQOS4VGzN0rxvLGRw/fyXIxL1MDOkaAO
l8SLSNuewY4XBUgISL3PMz123r18DAGOuy9mEcYU/IMesYD2F+wy5lJ17HIGq6X2
RpoF1p3qO1jfkPTKOob6Ixd4H5beJNPKpdth7LY3PJaVhDxgouj32fxnLnATVSnN
gENQ10fnt8BCjshRYW6Z2/9bF15JCkUFR1xdBW2/xh1oj+kvPqqqk2bEN1eVQzUy
2hT/XkwtpthqjSbX8NNavWRSFnOnbMLTRKQyIXmFVsM5VoSrwtiGsCFzBgcT++I=
=XIzU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- some cleanups
- direct physical timer assignment
- cache sanitization for 32-bit guests
s390:
- interrupt cleanup
- introduction of the Guest Information Block
- preparation for processor subfunctions in cpu models
PPC:
- bug fixes and improvements, especially related to machine checks
and protection keys
x86:
- many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations
- AVIC fixes
Generic:
- memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
kvm: vmx: fix formatting of a comment
KVM: doc: Document the life cycle of a VM and its resources
MAINTAINERS: Add KVM selftests to existing KVM entry
Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
KVM: PPC: Fix compilation when KVM is not enabled
KVM: Minor cleanups for kvm_main.c
KVM: s390: add debug logging for cpu model subfunctions
KVM: s390: implement subfunction processor calls
arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
KVM: arm/arm64: Remove unused timer variable
KVM: PPC: Book3S: Improve KVM reference counting
KVM: PPC: Book3S HV: Fix build failure without IOMMU support
Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
x86: kvmguest: use TSC clocksource if invariant TSC is exposed
KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
...
scripts/Makefile.build and arch/s390/boot/Makefile use the same
command (thin archiving with symbol table creation).
Avoid the code duplication, and move it to scripts/Makefile.lib.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add check for the return value of memblock_alloc*() functions and call
panic() in case of error. The panic message repeats the one used by
panicing memblock allocators with adjustment of parameters to include
only relevant ones.
The replacement was mostly automated with semantic patches like the one
below with manual massaging of format strings.
@@
expression ptr, size, align;
@@
ptr = memblock_alloc(size, align);
+ if (!ptr)
+ panic("%s: Failed to allocate %lu bytes align=0x%lx\n", __func__, size, align);
[anders.roxell@linaro.org: use '%pa' with 'phys_addr_t' type]
Link: http://lkml.kernel.org/r/20190131161046.21886-1-anders.roxell@linaro.org
[rppt@linux.ibm.com: fix format strings for panics after memblock_alloc]
Link: http://lkml.kernel.org/r/1548950940-15145-1-git-send-email-rppt@linux.ibm.com
[rppt@linux.ibm.com: don't panic if the allocation in sparse_buffer_init fails]
Link: http://lkml.kernel.org/r/20190131074018.GD28876@rapoport-lnx
[akpm@linux-foundation.org: fix xtensa printk warning]
Link: http://lkml.kernel.org/r/1548057848-15136-20-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Guo Ren <ren_guo@c-sky.com> [c-sky]
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390]
Reviewed-by: Juergen Gross <jgross@suse.com> [Xen]
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memblock_alloc_base() function tries to allocate a memory up to the
limit specified by its max_addr parameter and panics if the allocation
fails. Replace its usage with memblock_phys_alloc_range() and make the
callers check the return value and panic in case of error.
Link: http://lkml.kernel.org/r/1548057848-15136-10-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the memblock_phys_alloc() function an inline wrapper for
memblock_phys_alloc_range() and update the memblock_phys_alloc() callers
to check the returned value and panic in case of error.
Link: http://lkml.kernel.org/r/1548057848-15136-8-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com> [c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com> [Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current AP bus implementation periodically polls the AP configuration
to detect changes. When the AP configuration is dynamically changed via the
SE or an SCLP instruction, the changes will not be reflected to sysfs until
the next time the AP configuration is polled. The CHSC architecture
provides a Store Event Information (SEI) command to make notification of an
AP configuration change. This patch introduces a handler to process
notification from the CHSC SEI command by immediately kicking off an AP bus
scan-after-event.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Harald Freudenberger <FREUDE@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module build
- allow to add optional flags to dpkg-buildpackage when building deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=y9YG
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- do not generate unneeded top-level built-in.a
- let git ignore O= directory entirely
- optimize scripts/kallsyms slightly
- exclude DWARF info from *.s regardless of config options
- fix GCC toolchain search path for Clang to prepare ld.lld support
- do not generate modules.order when CONFIG_MODULES is disabled
- simplify single target rules and remove VPATH for external module
build
- allow to add optional flags to dpkg-buildpackage when building
deb-pkg
- move some compiler option tests from Makefile to Kconfig
- various Makefile cleanups
* tag 'kbuild-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (40 commits)
kbuild: remove scripts/basic/% build target
kbuild: use -Werror=implicit-... instead of -Werror-implicit-...
kbuild: clean up scripts/gcc-version.sh
kbuild: remove cc-version macro
kbuild: update comment block of scripts/clang-version.sh
kbuild: remove commented-out INITRD_COMPRESS
kbuild: move -gsplit-dwarf, -gdwarf-4 option tests to Kconfig
kbuild: [bin]deb-pkg: add DPKG_FLAGS variable
kbuild: move ".config not found!" message from Kconfig to Makefile
kbuild: invoke syncconfig if include/config/auto.conf.cmd is missing
kbuild: simplify single target rules
kbuild: remove empty rules for makefiles
kbuild: make -r/-R effective in top Makefile for old Make versions
kbuild: move tools_silent to a more relevant place
kbuild: compute false-positive -Wmaybe-uninitialized cases in Kconfig
kbuild: refactor cc-cross-prefix implementation
kbuild: hardcode genksyms path and remove GENKSYMS variable
scripts/gdb: refactor rules for symlink creation
kbuild: create symlink to vmlinux-gdb.py in scripts_gdb target
scripts/gdb: do not descend into scripts/gdb from scripts
...
First: Ted, Jaegeuk, and I have decided to add me as a co-maintainer for
fscrypt, and we're now using a shared git tree. So we've updated
MAINTAINERS accordingly, and I'm doing the pull request this time.
The actual changes for v5.1 are:
- Remove the fs-specific kconfig options like CONFIG_EXT4_ENCRYPTION and
make fscrypt support for all fscrypt-capable filesystems be controlled
by CONFIG_FS_ENCRYPTION, similar to how CONFIG_QUOTA works.
- Improve error code for rename() and link() into encrypted directories.
- Various cleanups.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCXH2YDRQcZWJpZ2dlcnNA
Z29vZ2xlLmNvbQAKCRDzXCl4vpKOK+SAAQCWYOTwYko8uE8Ze8i2fiUm0vr91NOg
zj5DGmK7Izxy/gEAsNDOVA7zWrDg/f5600/7aLpDQQTGHA38YVsgiyd7DgY=
=S3tT
-----END PGP SIGNATURE-----
Merge tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt
Pull fscrypt updates from Eric Biggers:
"First: Ted, Jaegeuk, and I have decided to add me as a co-maintainer
for fscrypt, and we're now using a shared git tree. So we've updated
MAINTAINERS accordingly, and I'm doing the pull request this time.
The actual changes for v5.1 are:
- Remove the fs-specific kconfig options like CONFIG_EXT4_ENCRYPTION
and make fscrypt support for all fscrypt-capable filesystems be
controlled by CONFIG_FS_ENCRYPTION, similar to how CONFIG_QUOTA
works.
- Improve error code for rename() and link() into encrypted
directories.
- Various cleanups"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
MAINTAINERS: add Eric Biggers as an fscrypt maintainer
fscrypt: return -EXDEV for incompatible rename or link into encrypted dir
fscrypt: remove filesystem specific build config option
f2fs: use IS_ENCRYPTED() to check encryption status
ext4: use IS_ENCRYPTED() to check encryption status
fscrypt: remove CRYPTO_CTR dependency
arm, s390 and unicore32 use oneliner wrappers for memblock_alloc().
Replace their usage with direct call to memblock_alloc().
Link: http://lkml.kernel.org/r/1546248566-14910-7-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several early memory allocations in arch/ code that use
memblock_phys_alloc() to allocate memory, convert the returned physical
address to the virtual address and then set the allocated memory to
zero.
Exactly the same behaviour can be achieved simply by calling
memblock_alloc(): it allocates the memory in the same way as
memblock_phys_alloc(), then it performs the phys_to_virt() conversion
and clears the allocated memory.
Replace the longer sequence with a simpler call to memblock_alloc().
Link: http://lkml.kernel.org/r/1546248566-14910-6-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (159 commits)
tools/testing/selftests/proc/proc-self-syscall.c: remove duplicate include
proc: more robust bulk read test
proc: test /proc/*/maps, smaps, smaps_rollup, statm
proc: use seq_puts() everywhere
proc: read kernel cpu stat pointer once
proc: remove unused argument in proc_pid_lookup()
fs/proc/thread_self.c: code cleanup for proc_setup_thread_self()
fs/proc/self.c: code cleanup for proc_setup_self()
proc: return exit code 4 for skipped tests
mm,mremap: bail out earlier in mremap_to under map pressure
mm/sparse: fix a bad comparison
mm/memory.c: do_fault: avoid usage of stale vm_area_struct
writeback: fix inode cgroup switching comment
mm/huge_memory.c: fix "orig_pud" set but not used
mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC
mm/memcontrol.c: fix bad line in comment
mm/cma.c: cma_declare_contiguous: correct err handling
mm/page_ext.c: fix an imbalance with kmemleak
mm/compaction: pass pgdat to too_many_isolated() instead of zone
mm: remove zone_lru_lock() function, access ->lru_lock directly
...
Pull perf updates from Ingo Molnar:
"Lots of tooling updates - too many to list, here's a few highlights:
- Various subcommand updates to 'perf trace', 'perf report', 'perf
record', 'perf annotate', 'perf script', 'perf test', etc.
- CPU and NUMA topology and affinity handling improvements,
- HW tracing and HW support updates:
- Intel PT updates
- ARM CoreSight updates
- vendor HW event updates
- BPF updates
- Tons of infrastructure updates, both on the build system and the
library support side
- Documentation updates.
- ... and lots of other changes, see the changelog for details.
Kernel side updates:
- Tighten up kprobes blacklist handling, reduce the number of places
where developers can install a kprobe and hang/crash the system.
- Fix/enhance vma address filter handling.
- Various PMU driver updates, small fixes and additions.
- refcount_t conversions
- BPF updates
- error code propagation enhancements
- misc other changes"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (238 commits)
perf script python: Add Python3 support to syscall-counts-by-pid.py
perf script python: Add Python3 support to syscall-counts.py
perf script python: Add Python3 support to stat-cpi.py
perf script python: Add Python3 support to stackcollapse.py
perf script python: Add Python3 support to sctop.py
perf script python: Add Python3 support to powerpc-hcalls.py
perf script python: Add Python3 support to net_dropmonitor.py
perf script python: Add Python3 support to mem-phys-addr.py
perf script python: Add Python3 support to failed-syscalls-by-pid.py
perf script python: Add Python3 support to netdev-times.py
perf tools: Add perf_exe() helper to find perf binary
perf script: Handle missing fields with -F +..
perf data: Add perf_data__open_dir_data function
perf data: Add perf_data__(create_dir|close_dir) functions
perf data: Fail check_backup in case of error
perf data: Make check_backup work over directories
perf tools: Add rm_rf_perf_data function
perf tools: Add pattern name checking to rm_rf
perf tools: Add depth checking to rm_rf
perf data: Add global path holder
...
To be able to judge the current overcommitment ratio for a CPU add
a lowcore field with the exponential moving average of the steal time.
The average is updated every tick.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a 64-bit process the randomization of the program break is quite
large with 1GB. That is as big as the randomization of the anonymous
mapping base, for a test case started with '/lib/ld64.so.1 <exec>'
it can happen that the heap is placed after the stack. To avoid
this limit the program break randomization to 32MB for 64-bit and
keep 8MB for 31-bit.
Reported-by: Stefan Liebler <stli@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The VDSO is part of the kernel image and therefore the struct pages are
marked as reserved during boot.
As we install a special mapping, the actual struct pages will never be
exposed to MM via the page tables. We can therefore leave the pages
marked as reserved.
Link: http://lkml.kernel.org/r/20190114125903.24845-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Suggested-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures like ppc64 require to do a conditional tlb flush based on
the old and new value of pte. Enable that by passing old pte value as
the arg.
Link: http://lkml.kernel.org/r/20190116085035.29729-3-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "NestMMU pte upgrade workaround for mprotect", v5.
We can upgrade pte access (R -> RW transition) via mprotect. We need to
make sure we follow the recommended pte update sequence as outlined in
commit bd5050e38a ("powerpc/mm/radix: Change pte relax sequence to
handle nest MMU hang") for such updates. This patch series does that.
This patch (of 5):
Some architectures may want to call flush_tlb_range from these helpers.
Link: http://lkml.kernel.org/r/20190116085035.29729-2-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull year 2038 updates from Thomas Gleixner:
"Another round of changes to make the kernel ready for 2038. After lots
of preparatory work this is the first set of syscalls which are 2038
safe:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
The syscall numbers are identical all over the architectures"
* 'timers-2038-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
riscv: Use latest system call ABI
checksyscalls: fix up mq_timedreceive and stat exceptions
unicore32: Fix __ARCH_WANT_STAT64 definition
asm-generic: Make time32 syscall numbers optional
asm-generic: Drop getrlimit and setrlimit syscalls from default list
32-bit userspace ABI: introduce ARCH_32BIT_OFF_T config option
compat ABI: use non-compat openat and open_by_handle_at variants
y2038: add 64-bit time_t syscalls to all 32-bit architectures
y2038: rename old time and utime syscalls
y2038: remove struct definition redirects
y2038: use time32 syscall names on 32-bit
syscalls: remove obsolete __IGNORE_ macros
y2038: syscalls: rename y2038 compat syscalls
x86/x32: use time64 versions of sigtimedwait and recvmmsg
timex: change syscalls to use struct __kernel_timex
timex: use __kernel_timex internally
sparc64: add custom adjtimex/clock_adjtime functions
time: fix sys_timer_settime prototype
time: Add struct __kernel_timex
time: make adjtime compat handling available for 32 bit
...
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the
CPU measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and
store thenn as event raw data.
- Bug fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcfh4QAAoJEDjwexyKj9rgXVAH/RzVbi3vznldujSNfCFTZKPu
EmFFAZIfbhifW3szfylyOJL52pFhxjcWzY0hkFEkbs2t90sn8l1BNkDscYZtfNHC
XvN3N9LsHyxOeyxvQuWLSio58qm+Lr1L0UrIhbMvqyAVkOLmIHvybFwi83OkMptm
djoL8NbuNsAA2s26y2bZLNtU7FmOW5smJIlnt7H4dmK4SFylqZKS/EnUZxGDgn+7
UrrTTOQUir0QZ8vraANsP1M0/LqPcd2YusLmj4jOdZ5Muc2Ch2AA991FofqdKShO
/8cGlsIzwHWGgdnP/YDea5gbetvonayYduixKy3EnYpWQ9iogiBjH4G7QNxcncs=
=v26J
-----END PGP SIGNATURE-----
Merge tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the CPU
measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and store
thenn as event raw data.
- Bug fixes and cleanups
* tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
Revert "s390/cpum_cf: Add kernel message exaplanations"
s390/dasd: fix read device characteristic with CONFIG_VMAP_STACK=y
s390/suspend: fix prefix register reset in swsusp_arch_resume
s390: warn about clearing als implied facilities
s390: allow overriding facilities via command line
s390: clean up redundant facilities list setup
s390/als: remove duplicated in-place implementation of stfle
s390/cio: Use cpa range elsewhere within vfio-ccw
s390/cio: Fix vfio-ccw handling of recursive TICs
s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
s390/cpum_cf: Handle EBUSY return code from CPU counter facility reservation
s390/cpum_cf: Add kernel message exaplanations
s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace
s390/cpum_cf: add ctr_stcctm() function
s390/cpum_cf: move common functions into a separate file
s390/cpum_cf: introduce kernel_cpumcf_avail() function
s390/cpu_mf: replace stcctm5() with the stcctm() function
s390/cpu_mf: add store cpu counter multiple instruction support
s390/cpum_cf: Add minimal in-kernel interface for counter measurements
s390/cpum_cf: introduce kernel_cpumcf_alert() to obtain measurement alerts
...
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:
1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
range without dealing with floods of ARP traffic, from Linus
Lüssing.
2) Throttle buffered multicast packet transmission in mt76, from
Felix Fietkau.
3) Support adaptive interrupt moderation in ice, from Brett Creeley.
4) A lot of struct_size conversions, from Gustavo A. R. Silva.
5) Add peek/push/pop commands to bpftool, as well as bash completion,
from Stanislav Fomichev.
6) Optimize sk_msg_clone(), from Vakul Garg.
7) Add SO_BINDTOIFINDEX, from David Herrmann.
8) Be more conservative with local resends due to local congestion,
from Yuchung Cheng.
9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.
10) Add health buffer support to devlink, from Eran Ben Elisha.
11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.
12) Add statistics to basic packet scheduler filter, from Cong Wang.
13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.
14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.
15) Add 3ad stats to bonding, from Nikolay Aleksandrov.
16) Lots of probing improvements for bpftool, from Quentin Monnet.
17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.
18) Allow #ebpf programs to access gso_segs from skb shared info, from
Eric Dumazet.
19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.
20) Support 22260 iwlwifi devices, from Luca Coelho.
21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.
22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.
23) Add spinlock support to #ebpf, from Alexei Starovoitov.
24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.
25) Add device infomation API to devlink, from Jakub Kicinski.
26) Add new timestamping socket options which are y2038 safe, from
Deepa Dinamani.
27) Add RX checksum offloading for various sh_eth chips, from Sergei
Shtylyov.
28) Flow offload infrastructure, from Pablo Neira Ayuso.
29) Numerous cleanups, improvements, and bug fixes to the PHY layer
and many drivers from Heiner Kallweit.
30) Lots of changes to try and make packet scheduler classifiers run
lockless as much as possible, from Vlad Buslov.
31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.
32) Add concurrency tests to tc-tests infrastructure, from Vlad
Buslov.
33) Add hwmon support to aquantia, from Heiner Kallweit.
34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.
And I would be remiss if I didn't thank the various major networking
subsystem maintainers for integrating much of this work before I even
saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
Johannes Berg, Kalle Valo, and many others. Thank you!"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
net/sched: avoid unused-label warning
net: ignore sysctl_devconf_inherit_init_net without SYSCTL
phy: mdio-mux: fix Kconfig dependencies
net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
selftest/net: Remove duplicate header
sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
net/mlx5e: Update tx reporter status in case channels were successfully opened
devlink: Add support for direct reporter health state update
devlink: Update reporter state to error even if recover aborted
sctp: call iov_iter_revert() after sending ABORT
team: Free BPF filter when unregistering netdev
ip6mr: Do not call __IP6_INC_STATS() from preemptible context
isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
cxgb4/chtls: Prefix adapter flags with CXGB4
net-sysfs: Switch to bitmap_zalloc()
mellanox: Switch to bitmap_zalloc()
bpf: add test cases for non-pointer sanitiation logic
mlxsw: i2c: Extend initialization by querying resources data
...
Every in-kernel use of this function defined it to KERNEL_DS (either as
an actual define, or as an inline function). It's an entirely
historical artifact, and long long long ago used to actually read the
segment selector valueof '%ds' on x86.
Which in the kernel is always KERNEL_DS.
Inspired by a patch from Jann Horn that just did this for a very small
subset of users (the ones in fs/), along with Al who suggested a script.
I then just took it to the logical extreme and removed all the remaining
gunk.
Roughly scripted with
git grep -l '(get_ds())' -- :^tools/ | xargs sed -i 's/(get_ds())/(KERNEL_DS)/'
git grep -lw 'get_ds' -- :^tools/ | xargs sed -i '/^#define get_ds()/d'
plus manual fixups to remove a few unusual usage patterns, the couple of
inline function cases and to fix up a comment that had become stale.
The 'get_ds()' function remains in an x86 kvm selftest, since in user
space it actually does something relevant.
Inspired-by: Jann Horn <jannh@google.com>
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reset of the prefix to zero in swsusp_arch_resume uses a 4 byte stack
slot. With CONFIG_VMAP_STACK=y this is now in the vmalloc area, this works
only with DAT enabled. Move the DAT disable in swsusp_arch_resume after
the prefix reset.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a warning about removing required architecture level set facilities
via "facilities=" command line option.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add "facilities=" command line option which allows to override
facility bits returned by stfle. The main purpose of that is debugging
aids which allows to test specific kernel behaviour depending on
specific facilities presence. It also affects CPU alternatives.
"facilities=" command line option format is comma separated list of
integer values to be additionally set or cleared (if value is starting
with "!"). Values ranges are also supported. e.g.:
facilities=!130-160,159,167-169
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Facilities list in the lowcore is initially set up by verify_facilities
from als.c and later initializations are redundant, so cleaning them up.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reuse __stfle call instead of in-place implementation. __stfle is using
memcpy and memset functions but they are safe to use, since mem.S is
built with -march=z900.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Clarify KVM related kernel messages
- Interrupt cleanup
- Introduction of the Guest Information Block (GIB)
- Preparation for processor subfunctions in cpu model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcb9iJAAoJEONU5rjiOLn4mI8P/1J3IyN3imnZUkTM5JOMWhNM
TSwh5obvn7dT6URZ6BgM1DWIz9E/FKrEb2kU4xr1hwf/a69Q1cYKVmHSnzzIpxHQ
ZNjr7QbcBCsVJ8LtasOoMmgGnVvtBYKKHr4J8UcqeW9raP3YfPJmqyETufiE2lFy
G50r8EBFr9rPh7nK7ImAabKC/7Q/qxZ0729m71cu729/uBb/Wf6frqaDmFlA8362
YZC7KY+xEHZbWqKQqAt/x1TWAOb7nA5dCzemeRckNrs5+FN7rSBrje6SbWApZPfn
weteCVbJMLCoRMUTFjRy3YNz1x0gAC9VQT6Qz5Kz7dColVfJjTPWdYuKpbRsj+n1
PEv1uuDBNbDqdS29KG3Dk9cfzUgAU12g+Xsb+3168HsQbU7XU1v6gCoRaR8ccaoq
3k8Em0xusHa+uGI6K4knKmWboRrCA6FWHIaink4B2K7qIaVdWqTebhHaDiDx8qB8
JRNjxQDho92FpRzxHyajHtamFKPjGT/Guc0yWMIrPHBn97GktUnDD6E5AdhTRVxs
aXTZv7XFq5j307lc3qWsdAf4zGEaPbi9f2nHgFK8hJf+z560CmNbye9Rw6L96Lil
gy0rvSQgN+3xBtSKvq3DNrgoouupOS6kFu5iyYLBS8UUOztXttKEzTCs+M87/3AP
fphwixKEEXsMRWR2SJvG
=YeIb
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
KVM: s390: Features for 5.1
- Clarify KVM related kernel messages
- Interrupt cleanup
- Introduction of the Guest Information Block (GIB)
- Preparation for processor subfunctions in cpu model
As userspace can now get/set the subfunctions we want to trace those.
This will allow to also check QEMUs cpu model vs. what the real
hardware provides.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
While we will not implement interception for query functions yet, we can
and should disable functions that have a control bit based on the given
CPU model.
Let us start with enabling the subfunction interface.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Rservation of the CPU Measurement Counter facility may fail if
it is already in use by the cf_diag device driver.
This is indicated by a non zero return code (-EBUSY).
However this return code is ignored and the counter facility
may be used in parallel by different device drivers.
Handle the failing reservation and return an error to the
caller.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a PMU device named cpum_cf_diag. It extracts the
values of all counters in all authorized counter sets and stores
them as event raw data. This is done with the STORE CPU COUNTER
MULTIPLE instruction to speed up access. All counter sets
fit into one buffer. The values of each counter are taken
when the event is started on the performance sub-system and when
the event is stopped.
This results in counter values available at the start and
at the end of the measurement time frame. The difference is
calculated for each counter. The differences of all
counters are then saved as event raw data in the perf.data
file.
The counter values are accompanied by the time stamps
when the counter set was started and when the counter set
was stopped. This data is part of a trailer entry which
describes the time frame, counter set version numbers,
CPU speed, and machine type for later analysis.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce the ctr_stcctm() function as wrapper function to extract counters
from a particular counter set. Note that the counter set is part of the
stcctm instruction opcode, few indirections are necessary to specify the
counter set as variable.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move common functions of the couter facility support into a separate
file.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A preparation to move out common CPU-MF counter facility support
functions, first introduce a function that indicates whether the
support is ready to use.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the stcctm5() function to extract counters from the MT-diagnostic
counter set with the stcctm() function. For readability, introduce an
enum to map the counter sets names to respective numbers for the stcctm
instruction.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for the STORE CPU COUNTER MULTIPLE instruction to extract
a range of counters from a counter set.
An assembler macro is used to create the instruction opcode because
the counter set identifier is part of the instruction and, thus,
cannot be easily specified as parameter.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a minimal interface for doing counter measurements of small
units of work within the kernel. Use the kernel_cpumcf_begin() function
start a measurement session and, later, stop it with kernel_cpumcf_end().
During the measreument session, you can enable and start/stop counter sets
by using ctr_set_* functions. To make these changes effective use the
lcctl() function. You can then use the ecctr() function to extract counters
from the different counter sets.
Please note that you have to check whether the counter sets to be enabled
are authorized.
Note that when a measurement session is active, other users cannot perform
counter measurements. In such cases, kernel_cpumcf_begin() indicates this
with returning -EBUSY. If the counter facility is not available,
kernel_cpumcf_begin() returns -ENODEV.
Note that this interface is restricted to the current CPU and, thus,
preemption must be turned off.
Example:
u32 state, err;
u64 cycles, insn;
err = kernel_cpumcf_begin();
if (err)
goto out_busy;
state = 0;
ctr_set_enable(&state, CPUMF_CTR_SET_BASIC);
ctr_set_start(&state, CPUMF_CTR_SET_BASIC);
err = lcctl(state);
if (err)
goto ;
/* ... do your work ... */
ctr_set_stop(&state, CPUMF_CTR_SET_BASIC);
err = lcctl(state);
if (err)
goto out;
cycles = insn = 0;
ecctr(0, &cycles);
ecctr(1, &insn);
/* ... */
kernel_cpumcf_end();
out_busy:
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
During a __kernel_cpumcf_begin()/end() session, save measurement alerts
for the counter facility in the per-CPU cpu_cf_events variable.
Users can obtain and, optionally, clear the alerts by calling
kernel_cpumcf_alert() to specifically handle alerts.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the struct cpu_cf_events and the respective per-CPU variable available
to in-kernel users. Access to this per-CPU variable shall be done between
the calls to __kernel_cpumcf_begin() and __kernel_cpumcf_end().
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rename the struct cpu_hw_events to cpu_cf_events and also the respective
per-CPU variable to make its name more clear. No functional changes.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Prepare the counter facility support to be used by other in-kernel
users. The first step introduces the __kernel_cpumcf_begin() and
__kernel_cpumcf_end() functions to reserve the counter facility
for doing measurements and to release after the measurements are
done.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move counter set specific controls and functions to the asm/cpu_mcf.h
header file containg all counter facility support definitions. Also
adapt few variable names and header file includes. No functional changes.
Signed-off-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pnetids are retrieved from the underlying hardware as EBCDIC. This patch
converts pnetids to ASCII.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DCSS range is currently printed with %p, which results in hashed values
instead of the actual addresses.
Use %px instead, the DCSS ranges do not reveal any kernel symbol addresses.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All supported releases of z/VM allow 64 bit subcodes and addressing mode
for diag 0x64.
This patch removes a lot of code for handling 31 bit addressing mode and
old subcodes.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
kvm_arch_memslots_updated() is at this point in time an x86-specific
hook for handling MMIO generation wraparound. x86 stashes 19 bits of
the memslots generation number in its MMIO sptes in order to avoid
full page fault walks for repeat faults on emulated MMIO addresses.
Because only 19 bits are used, wrapping the MMIO generation number is
possible, if unlikely. kvm_arch_memslots_updated() alerts x86 that
the generation has changed so that it can invalidate all MMIO sptes in
case the effective MMIO generation has wrapped so as to avoid using a
stale spte, e.g. a (very) old spte that was created with generation==0.
Given that the purpose of kvm_arch_memslots_updated() is to prevent
consuming stale entries, it needs to be called before the new generation
is propagated to memslots. Invalidating the MMIO sptes after updating
memslots means that there is a window where a vCPU could dereference
the new memslots generation, e.g. 0, and incorrectly reuse an old MMIO
spte that was created with (pre-wrap) generation==0.
Fixes: e59dbe09f8 ("KVM: Introduce kvm_arch_memslots_updated()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The fix to make WARN work in the early boot code created a problem
on older machines without EDAT-1. The setup_lowcore_dat_on function
uses the pointer from lowcore_ptr[0] to set the DAT bit in the new
PSWs. That does not work if the kernel page table is set up with
4K pages as the prefix address maps to absolute zero.
To make this work the PSWs need to be changed with via address 0 in
form of the S390_lowcore definition.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Cornelia Huck <cohuck@redhat.com>
Fixes: 94f85ed3e2f8 ("s390/setup: fix early warning messages")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The setup_lowcore() function creates a new prefix page for the boot CPU.
The PSW mask for the system_call, external interrupt, i/o interrupt and
the program check handler have the DAT bit set in this new prefix page.
At the time setup_lowcore is called the system still runs without virtual
address translation, the paging_init() function creates the kernel page
table and loads the CR13 with the kernel ASCE.
Any code between setup_lowcore() and the end of paging_init() that has
a BUG or WARN statement will create a program check that can not be
handled correctly as there is no kernel page table yet.
To allow early WARN statements initially setup the lowcore with DAT off
and set the DAT bit only after paging_init() has completed.
Cc: stable@vger.kernel.org
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[heiko.carstens@de.ibm.com]:
-----
Laura Abbott reported that the kernel doesn't build anymore with gcc 9,
due to the "X" constraint. Ilya provided the gcc 9 patch "S/390:
Introduce jdd constraint" which introduces the new "jdd" constraint
which fixes this.
-----
The support for section anchors on S/390 introduced in gcc9 has changed
the behavior of "X" constraint, which can now produce register
references. Since existing constraints, in particular, "i", do not fit
the intended use case on S/390, the new machine-specific "jdd"
constraint was introduced. This patch makes jump labels use "jdd"
constraint when building with gcc9.
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
When facility.76 MSAX3 is present for the guest we must issue a validity
interception if the CRYCBD is not valid.
The bit CRYCBD.31 is an effective field and tested at each guest level
and has for effect to mask the facility.76
It follows that if CRYCBD.31 is clear and AP is not in use we do not
have to test the CRYCBD validatity even if facility.76 is present in the
host.
Fixes: 6ee7409820 ("KVM: s390: vsie: allow CRYCB FORMAT-0")
Cc: stable@vger.kernel.org
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reported-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1549876849-32680-1-git-send-email-pmorel@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This series finally gets us to the point of having system calls with
64-bit time_t on all architectures, after a long time of incremental
preparation patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures
using the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call
that includes a 'struct timespec' argument, or a structure containing
a timespec or (in case of clock_adjtime) timeval. Not included here
are new versions of getitimer/setitimer and getrusage/waitid, which
are planned for the future but only needed to make a consistent API
rather than for correct operation beyond y2038. These four system
calls are based on 'timeval', and it has not been finally decided
what the replacement kernel interface will use instead.
So far, I have done a lot of build testing across most architectures,
which has found a number of bugs. Runtime testing so far included
testing LTP on 32-bit ARM with the existing system calls, to ensure
we do not regress for existing binaries, and a test with a 32-bit
x86 build of LTP against a modified version of the musl C library
that has been adapted to the new system call interface [3].
This library can be used for testing on all architectures supported
by musl-1.1.21, but it is not how the support is getting integrated
into the official musl release. Official musl support is planned
but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IZVb
-----END PGP SIGNATURE-----
Merge tag 'y2038-new-syscalls' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull y2038 - time64 system calls from Arnd Bergmann:
This series finally gets us to the point of having system calls with 64-bit
time_t on all architectures, after a long time of incremental preparation
patches.
There was actually one conversion that I missed during the summer,
i.e. Deepa's timex series, which I now updated based the 5.0-rc1 changes
and review comments.
The following system calls are now added on all 32-bit architectures using
the same system call numbers:
403 clock_gettime64
404 clock_settime64
405 clock_adjtime64
406 clock_getres_time64
407 clock_nanosleep_time64
408 timer_gettime64
409 timer_settime64
410 timerfd_gettime64
411 timerfd_settime64
412 utimensat_time64
413 pselect6_time64
414 ppoll_time64
416 io_pgetevents_time64
417 recvmmsg_time64
418 mq_timedsend_time64
419 mq_timedreceiv_time64
420 semtimedop_time64
421 rt_sigtimedwait_time64
422 futex_time64
423 sched_rr_get_interval_time64
Each one of these corresponds directly to an existing system call that
includes a 'struct timespec' argument, or a structure containing a timespec
or (in case of clock_adjtime) timeval. Not included here are new versions
of getitimer/setitimer and getrusage/waitid, which are planned for the
future but only needed to make a consistent API rather than for correct
operation beyond y2038. These four system calls are based on 'timeval', and
it has not been finally decided what the replacement kernel interface will
use instead.
So far, I have done a lot of build testing across most architectures, which
has found a number of bugs. Runtime testing so far included testing LTP on
32-bit ARM with the existing system calls, to ensure we do not regress for
existing binaries, and a test with a 32-bit x86 build of LTP against a
modified version of the musl C library that has been adapted to the new
system call interface [3]. This library can be used for testing on all
architectures supported by musl-1.1.21, but it is not how the support is
getting integrated into the official musl release. Official musl support is
planned but will require more invasive changes to the library.
Link: https://lore.kernel.org/lkml/20190110162435.309262-1-arnd@arndb.de/T/
Link: https://lore.kernel.org/lkml/20190118161835.2259170-1-arnd@arndb.de/
Link: https://git.linaro.org/people/arnd/musl-y2038.git/ [2]
The system call tables have diverged a bit over the years, and a number
of the recent additions never made it into all architectures, for one
reason or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all
architectures but that we definitely want there. This includes
{,f}statfs64() and get{eg,eu,g,p,u,pp}id() on alpha, which have
been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like
what we do on other architectures, while keeping the 31-bit
pointer extension. This was merged as a shared branch by the
s390 maintainers and is included here in order to base the other
patches on top.
- Add the separate ipc syscalls on all architectures that
traditionally only had sys_ipc(). This version is done without
support for IPC_OLD that is we have in sys_ipc. The
new semtimedop_time64 syscall will only be added here, not
in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably
don't need everywhere, in particular pkey_* and rseq,
for the purpose of symmetry: if it's in asm-generic/unistd.h,
it makes sense to have it everywhere. I expect that any future
system calls will get assigned on all platforms together, even
when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future
calls. In combination with the generated tables, this hopefully
makes it easier to add new calls across all architectures
together.
All of the above are technically separate from the y2038 work,
but are done as preparation before we add the new 64-bit time_t
system calls everywhere, providing a common baseline set of system
calls.
I expect that glibc and other libraries that want to use 64-bit
time_t will require linux-5.1 kernel headers for building in
the future, and at a much later point may also require linux-5.1
or a later version as the minimum kernel at runtime. Having a
common baseline then allows the removal of many architecture or
kernel version specific workarounds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=s4wf
-----END PGP SIGNATURE-----
Merge tag 'y2038-syscall-cleanup' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground into timers/2038
Pull preparatory work for y2038 changes from Arnd Bergmann:
System call unification and cleanup
The system call tables have diverged a bit over the years, and a number of
the recent additions never made it into all architectures, for one reason
or another.
This is an attempt to clean it up as far as we can without breaking
compatibility, doing a number of steps:
- Add system calls that have not yet been integrated into all architectures
but that we definitely want there. This includes {,f}statfs64() and
get{eg,eu,g,p,u,pp}id() on alpha, which have been missing traditionally.
- The s390 compat syscall handling is cleaned up to be more like what we
do on other architectures, while keeping the 31-bit pointer
extension. This was merged as a shared branch by the s390 maintainers
and is included here in order to base the other patches on top.
- Add the separate ipc syscalls on all architectures that traditionally
only had sys_ipc(). This version is done without support for IPC_OLD
that is we have in sys_ipc. The new semtimedop_time64 syscall will only
be added here, not in sys_ipc
- Add syscall numbers for a couple of syscalls that we probably don't need
everywhere, in particular pkey_* and rseq, for the purpose of symmetry:
if it's in asm-generic/unistd.h, it makes sense to have it everywhere. I
expect that any future system calls will get assigned on all platforms
together, even when they appear to be specific to a single architecture.
- Prepare for having the same system call numbers for any future calls. In
combination with the generated tables, this hopefully makes it easier to
add new calls across all architectures together.
All of the above are technically separate from the y2038 work, but are done
as preparation before we add the new 64-bit time_t system calls everywhere,
providing a common baseline set of system calls.
I expect that glibc and other libraries that want to use 64-bit time_t will
require linux-5.1 kernel headers for building in the future, and at a much
later point may also require linux-5.1 or a later version as the minimum
kernel at runtime. Having a common baseline then allows the removal of many
architecture or kernel version specific workarounds.
There is no need to define these PNETID related constants in
the pnet.h file, since they are just used locally within pnet.c.
Just code cleanup, no functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The z14 introduced alignment hints to increase the performance of
vector loads and stores. The kernel uses an implicit alignmenet
of 8 bytes for the vector registers, set the alignment hint to 3.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no need to use void pointers, all drivers are in agreement
about the underlying data structure of the SBAL arrays.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Map IOV resources such that pci common code recognizes the IOV
capability of PFs.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve the bar check in pci_iomap_range to cover functions
for which we recognize more bars than what we can access due
to AR restrictions.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 version of the mmap_base function is ignorant of stack_guard_gap
which can lead to a placement of the stack vs. the mmap base that does not
leave enough space for the stack rlimit.
Add the stack_guard_gap to the calculation and while we are at it the
check for gap+pad overflows as well.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove some dead code from head64.S, which was left over since commit
da292bbe1f ("[S390] eliminate ipl_device from lowcore") removed
ipl_device from lowcore.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The #ifdef CONFIG_DMA_API_DEBUG check in reserve_kernel() is no longer
needed, since commit ea535e418c ("dma-debug: switch check from _text
to _stext") changed the logic in lib/dma-debug.c, so remove it.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This reverts commit 9594ca6b87.
With the handle_simple_irq irq_flow_handler it must be ensured to
not call generic_handle_irq with the same IRQ number on 2 CPUs at
the same time (interrupts are floating on s390).
Contrary to my initial investigation the irq_desc's lock usage in
handle_simple_irq does not ensure this. Thus re-introduce the bit-
lock usage in s390's pci handler.
Reported-by: Ursula Braun <ubraun@linux.ibm.com>
Reported-by: Alexander Schmidt <alexs@linux.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This adds 21 new system calls on each ABI that has 32-bit time_t
today. All of these have the exact same semantics as their existing
counterparts, and the new ones all have macro names that end in 'time64'
for clarification.
This gets us to the point of being able to safely use a C library
that has 64-bit time_t in user space. There are still a couple of
loose ends to tie up in various areas of the code, but this is the
big one, and should be entirely uncontroversial at this point.
In particular, there are four system calls (getitimer, setitimer,
waitid, and getrusage) that don't have a 64-bit counterpart yet,
but these can all be safely implemented in the C library by wrapping
around the existing system calls because the 32-bit time_t they
pass only counts elapsed time, not time since the epoch. They
will be dealt with later.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
The time, stime, utime, utimes, and futimesat system calls are only
used on older architectures, and we do not provide y2038 safe variants
of them, as they are replaced by clock_gettime64, clock_settime64,
and utimensat_time64.
However, for consistency it seems better to have the 32-bit architectures
that still use them call the "time32" entry points (leaving the
traditional handlers for the 64-bit architectures), like we do for system
calls that now require two versions.
Note: We used to always define __ARCH_WANT_SYS_TIME and
__ARCH_WANT_SYS_UTIME and only set __ARCH_WANT_COMPAT_SYS_TIME and
__ARCH_WANT_SYS_UTIME32 for compat mode on 64-bit kernels. Now this is
reversed: only 64-bit architectures set __ARCH_WANT_SYS_TIME/UTIME, while
we need __ARCH_WANT_SYS_TIME32/UTIME32 for 32-bit architectures and compat
mode. The resulting asm/unistd.h changes look a bit counterintuitive.
This is only a cleanup patch and it should not change any behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
These are all for ignoring the lack of obsolete system calls,
which have been marked the same way in scripts/checksyscall.sh,
so these can be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
A lot of system calls that pass a time_t somewhere have an implementation
using a COMPAT_SYSCALL_DEFINEx() on 64-bit architectures, and have
been reworked so that this implementation can now be used on 32-bit
architectures as well.
The missing step is to redefine them using the regular SYSCALL_DEFINEx()
to get them out of the compat namespace and make it possible to build them
on 32-bit architectures.
Any system call that ends in 'time' gets a '32' suffix on its name for
that version, while the others get a '_time32' suffix, to distinguish
them from the normal version, which takes a 64-bit time argument in the
future.
In this step, only 64-bit architectures are changed, doing this rename
first lets us avoid touching the 32-bit architectures twice.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When pmu::setup_aux() is called the coresight PMU needs to know which
sink to use for the session by looking up the information in the
event's attr::config2 field.
As such simply replace the cpu information by the complete perf_event
structure and change all affected customers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki Poulouse <suzuki.poulose@arm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20190131184714.20388-2-mathieu.poirier@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Assure a GISA is in use before accessing the IPM to avoid a
null pointer dereference issue.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-16-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
By initializing the GIB, it will be used by the kvm host.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-15-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The patch implements a handler for GIB alert interruptions
on the host. Its task is to alert guests that interrupts are
pending for them.
A GIB alert interrupt statistic counter is added as well:
$ cat /proc/interrupts
CPU0 CPU1
...
GAL: 23 37 [I/O] GIB Alert
...
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <20190131085247.13826-14-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Function kvm_s390_gisa_clear() now clears the Interruption
Pending Mask of the GISA asap. If the GISA is in the alert
list at this time it stays in the list but is removed by
process_gib_alert_list().
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Message-Id: <20190131085247.13826-13-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add the Interruption Alert Mask (IAM) to the architecture specific
kvm struct. This mask in the GISA is used to define for which ISC
a GIB alert will be issued.
The functions kvm_s390_gisc_register() and kvm_s390_gisc_unregister()
are used to (un)register a GISC (guest ISC) with a virtual machine and
its GISA.
Upon successful completion, kvm_s390_gisc_register() returns the
ISC to be used for GIB alert interruptions. A negative return code
indicates an error during registration.
Theses functions will be used by other adapter types like AP and PCI to
request pass-through interruption support.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-12-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Adding the kvm reference to struct sie_page2 will allow to
determine the kvm a given gisa belongs to:
container_of(gisa, struct sie_page2, gisa)->kvm
This functionality will be required to process a gisa in
gib alert interruption context.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-11-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The Guest Information Block (GIB) links the GISA of all guests
that have adapter interrupts pending. These interrupts cannot be
delivered because all vcpus of these guests are currently in WAIT
state or have masked the respective Interruption Sub Class (ISC).
If enabled, a GIB alert is issued on the host to schedule these
guests to run suitable vcpus to consume the pending interruptions.
This mechanism allows to process adapter interrupts for currently
not running guests.
The GIB is created during host initialization and associated with
the Adapter Interruption Facility in case an Adapter Interruption
Virtualization Facility is available.
The GIB initialization and thus the activation of the related code
will be done in an upcoming patch of this series.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-10-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch implements the Set Guest Information Block operation
to request association or disassociation of a Guest Information
Block (GIB) with the Adapter Interruption Facility. The operation
is required to receive GIB alert interrupts for guest adapters
in conjunction with AIV and GISA.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190131085247.13826-9-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Use this struct analog to the kvm interruption structs
for kvm emulated floating and local interruptions.
GIB handling will add further fields to this structure as
required.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-8-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This will shorten the length of code lines. All GISA related
static inline functions are local to interrupt.c.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-7-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Interruption types that are not represented in GISA shall
use pending_irqs_no_gisa() to test pending interruptions.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-6-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The change helps to reduce line length and
increases code readability.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-5-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The vcpu idle_mask state is used by but not specific
to the emulated floating interruptions. The state is
relevant to gisa related interruptions as well.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-4-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Use a consistent bitmap declaration throughout the code.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-3-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The explicit else path specified in set_intercept_indicators_io
is not required as the function returns in case the first branch
is taken anyway.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20190131085247.13826-2-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
As suggested by our ID dept. here are some kernel message
updates.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Commit 626a5f66da ("s390: bpf: implement jitting of JMP32") added
JMP32 code-gen support for s390. However it triggers the warning below
due to some unusual gotos in the original s390 bpf jit code.
Add a couple of additional "is_jmp32" initializations to fix this.
Also fix the wrong opcode for the "llilf" instruction that was
introduced with the same commit.
arch/s390/net/bpf_jit_comp.c: In function 'bpf_jit_insn':
arch/s390/net/bpf_jit_comp.c:248:55: warning: 'is_jmp32' may be used uninitialized in this function [-Wmaybe-uninitialized]
_EMIT6(op1 | reg(b1, b2) << 16 | (rel & 0xffff), op2 | mask); \
^
arch/s390/net/bpf_jit_comp.c:1211:8: note: 'is_jmp32' was declared here
bool is_jmp32 = BPF_CLASS(insn->code) == BPF_JMP32;
Fixes: 626a5f66da ("s390: bpf: implement jitting of JMP32")
Cc: Jiong Wang <jiong.wang@netronome.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-01-29
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Teach verifier dead code removal, this also allows for optimizing /
removing conditional branches around dead code and to shrink the
resulting image. Code store constrained architectures like nfp would
have hard time doing this at JIT level, from Jakub.
2) Add JMP32 instructions to BPF ISA in order to allow for optimizing
code generation for 32-bit sub-registers. Evaluation shows that this
can result in code reduction of ~5-20% compared to 64 bit-only code
generation. Also add implementation for most JITs, from Jiong.
3) Add support for __int128 types in BTF which is also needed for
vmlinux's BTF conversion to work, from Yonghong.
4) Add a new command to bpftool in order to dump a list of BPF-related
parameters from the system or for a specific network device e.g. in
terms of available prog/map types or helper functions, from Quentin.
5) Add AF_XDP sock_diag interface for querying sockets from user
space which provides information about the RX/TX/fill/completion
rings, umem, memory usage etc, from Björn.
6) Add skb context access for skb_shared_info->gso_segs field, from Eric.
7) Add support for testing flow dissector BPF programs by extending
existing BPF_PROG_TEST_RUN infrastructure, from Stanislav.
8) Split BPF kselftest's test_verifier into various subgroups of tests
in order better deal with merge conflicts in this area, from Jakub.
9) Add support for queue/stack manipulations in bpftool, from Stanislav.
10) Document BTF, from Yonghong.
11) Dump supported ELF section names in libbpf on program load
failure, from Taeung.
12) Silence a false positive compiler warning in verifier's BTF
handling, from Peter.
13) Fix help string in bpftool's feature probing, from Prashant.
14) Remove duplicate includes in BPF kselftests, from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390x diagnose 318 instruction sets the control program name code (CPNC)
and control program version code (CPVC) to provide useful information
regarding the OS during debugging. The CPNC is explicitly set to 4 to
indicate a Linux/KVM environment.
The CPVC is a 7-byte value containing:
- 3-byte Linux version code, currently set to 0
- 3-byte unique value, currently set to 0
- 1-byte trailing null
Signed-off-by: Collin Walling <walling@linux.ibm.com>
Acked-by: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <1544135405-22385-2-git-send-email-walling@linux.ibm.com>
[set version code to 0 until the structure is fully defined]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The patch that added support for the virtually mapped kernel stacks changed
swsusp_arch_suspend to switch to the nodat-stack as the vmap stack is not
available while going in and out of suspend.
Unfortunately the switch to the nodat-stack is incorrect which breaks
suspend to disk.
Cc: stable@vger.kernel.org # v4.20
Fixes: ce3dc44749 ("s390: add support for virtually mapped kernel stacks")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In Kbuild, if_changed and friends must have FORCE as a prerequisite.
Hence, $(filter-out FORCE,$^) or $(filter-out $(PHONY),$^) is a common
idiom to get the names of all the prerequisites except phony targets.
Add real-prereqs as a shorthand.
Note:
We cannot replace $(filter %.o,$^) in cmd_link_multi-m because $^ may
include auto-generated dependencies from the .*.cmd file when a single
object module is changed into a multi object module. Refer to commit
69ea912fda ("kbuild: remove unneeded link_multi_deps"). I added some
comment to avoid accidental breakage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
When I was refactoring cmd_ar_builtin in scripts/Makefile.build,
I noticed the build breakage of s390.
Some Makefiles of s390 add extra dependencies to built-in.a;
built-in.a depends on timestamp files *.o.chkbss, but $(AR) does
not want to include them into built-in.a.
Insert a phony target 'chkbss' in between so that $(AR) can take
$(filter-out $(PHONY), $^) as input.
While I was here, I refactored Makefile.chkbss a little bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This patch implements code-gen for new JMP32 instructions on s390.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Most architectures define system call numbers for the rseq and pkey system
calls, even when they don't support the features, and perhaps never will.
Only a few architectures are missing these, so just define them anyway
for consistency. If we decide to add them later to one of these, the
system call numbers won't get out of sync then.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
The IPC system call handling is highly inconsistent across architectures,
some use sys_ipc, some use separate calls, and some use both. We also
have some architectures that require passing IPC_64 in the flags, and
others that set it implicitly.
For the addition of a y2038 safe semtimedop() system call, I chose to only
support the separate entry points, but that requires first supporting
the regular ones with their own syscall numbers.
The IPC_64 is now implied by the new semctl/shmctl/msgctl system
calls even on the architectures that require passing it with the ipc()
multiplexer.
I'm not adding the new semtimedop() or semop() on 32-bit architectures,
those will get implemented using the new semtimedop_time64() version
that gets added along with the other time64 calls.
Three 64-bit architectures (powerpc, s390 and sparc) get semtimedop().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
CRYPTO_TFM_REQ_WEAK_KEY confuses newcomers to the crypto API because it
sounds like it is requesting a weak key. Actually, it is requesting
that weak keys be forbidden (for algorithms that have the notion of
"weak keys"; currently only DES and XTS do).
Also it is only one letter away from CRYPTO_TFM_RES_WEAK_KEY, with which
it can be easily confused. (This in fact happened in the UX500 driver,
though just in some debugging messages.)
Therefore, make the intent clear by renaming it to
CRYPTO_TFM_REQ_FORBID_WEAK_KEYS.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to have a common code base for fscrypt "post read" processing
for all filesystems which support encryption, this commit removes
filesystem specific build config option (e.g. CONFIG_EXT4_FS_ENCRYPTION)
and replaces it with a build option (i.e. CONFIG_FS_ENCRYPTION) whose
value affects all the filesystems making use of fscrypt.
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
When converting to autogenerated compat syscall wrappers all system
call entry points got a different symbol name: they all got a __s390x_
prefix.
This caused breakage with system call tracing, since an appropriate
arch_syscall_match_sym_name() was not provided. Add this function, and
while at it also add code to avoid compat system call tracing. s390
has different system call tables for native 64 bit system calls and
compat system calls. This isn't really supported in the common
code. However there are hardly any compat binaries left, therefore
just ignore compat system calls, like x86 and arm64 also do for the
same reason.
Fixes: aa0d6e70d3 ("s390: autogenerate compat syscall wrappers")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid using arch specific implementations of string/memory functions
with KASAN since gcc cannot instrument asm code memory accesses and
many bugs could be missed.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
These two functions are only used by core MM code, so no need to export
them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that all these wrappers are automatically generated, we can
remove the entire file, and instead point to the regualar syscalls
like all other architectures do.
The 31-bit pointer extension is now handled in the __s390_sys_*()
wrappers.
Link: https://lore.kernel.org/lkml/20190116131527.2071570-6-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Any system call that takes a pointer argument on s390 requires
a wrapper function to do a 31-to-64 zero-extension, these are
currently generated in arch/s390/kernel/compat_wrapper.c.
On arm64 and x86, we already generate similar wrappers for all
system calls in the place of their definition, just for a different
purpose (they load the arguments from pt_regs).
We can do the same thing here, by adding an asm/syscall_wrapper.h
file with a copy of all the relevant macros to override the generic
version. Besides the addition of the compat entry point, these also
rename the entry points with a __s390_ or __s390x_ prefix, similar
to what we do on arm64 and x86. This in turn requires renaming
a few things, and adding a proper ni_syscall() entry point.
In order to still compile system call definitions that pass an
loff_t argument, the __SC_COMPAT_CAST() macro checks for that
and forces an -ENOSYS error, which was the best I could come up
with. Those functions must obviously not get called from user
space, but instead require hand-written compat_sys_*() handlers,
which fortunately already exist.
Link: https://lore.kernel.org/lkml/20190116131527.2071570-5-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[heiko.carstens@de.ibm.com: compile fix for !CONFIG_COMPAT]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390 has an almost identical copy of the code in kernel/uid16.c.
The problem here is that it requires calling the regular system calls,
which the generic implementation handles correctly, but the internal
interfaces are not declared in a global header for this.
The best way forward here seems to be to just use the generic code and
delete the s390 specific implementation.
I keep the changes to uapi/asm/posix_types.h inside of an #ifdef check
so user space does not observe any changes. As some of the system calls
pass pointers, we also need wrappers in compat_wrapper.c, which I add
for all calls with at least one argument. All those wrappers can be
removed in a later step.
Link: https://lore.kernel.org/lkml/20190116131527.2071570-4-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sys_ipc() and compat_ksys_ipc() functions are meant to only
be used from the system call table, not called by another function.
Introduce ksys_*() interfaces for this purpose, as we have done
for many other system calls.
Link: https://lore.kernel.org/lkml/20190116131527.2071570-3-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
[heiko.carstens@de.ibm.com: compile fix for !CONFIG_COMPAT]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Patch series "s390: rework compat wrapper generation".
As promised, I gave this a go and changed the SYSCALL_DEFINEx()
infrastructure to always include the wrappers for doing the
31-bit argument conversion on s390 compat mode.
This does three main things:
- The UID16 rework saved a lot of duplicated code, and would
probably make sense by itself, but is also required as
we can no longer call sys_*() functions directly after the
last step.
- Removing the compat_wrapper.c file is of course the main
goal here, in order to remove the need to maintain the
compat_wrapper.c file when new system calls get added.
Unfortunately, this requires adding some complexity in
syscall_wrapper.h, and trades a small reduction in source
code lines for a small increase in binary size for
unused wrappers.
- As an added benefit, the use of syscall_wrapper.h now makes
it easy to change the syscall wrappers so they no longer
see all user space register contents, similar to changes
done in commits fa697140f9 ("syscalls/x86: Use 'struct pt_regs'
based syscall calling convention for 64-bit syscalls") and
4378a7d4be ("arm64: implement syscall wrappers").
I leave the actual implementation of this for you, if you
want to do it later.
I did not test the changes at runtime, but I looked at the
generated object code, which seems fine here and includes
the same conversions as before.
This patch(of 5):
The sys_personality function is not meant to be called from other system
calls. We could introduce an intermediate ksys_personality function,
but it does almost nothing, so this just moves the implementation into
the caller.
Link: https://lore.kernel.org/lkml/20190116131527.2071570-1-arnd@arndb.de
Link: https://lore.kernel.org/lkml/20190116131527.2071570-2-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This introduces a new generic SOL_SOCKET-level socket option called
SO_BINDTOIFINDEX. It behaves similar to SO_BINDTODEVICE, but takes a
network interface index as argument, rather than the network interface
name.
User-space often refers to network-interfaces via their index, but has
to temporarily resolve it to a name for a call into SO_BINDTODEVICE.
This might pose problems when the network-device is renamed
asynchronously by other parts of the system. When this happens, the
SO_BINDTODEVICE might either fail, or worse, it might bind to the wrong
device.
In most cases user-space only ever operates on devices which they
either manage themselves, or otherwise have a guarantee that the device
name will not change (e.g., devices that are UP cannot be renamed).
However, particularly in libraries this guarantee is non-obvious and it
would be nice if that race-condition would simply not exist. It would
make it easier for those libraries to operate even in situations where
the device-name might change under the hood.
A real use-case that we recently hit is trying to start the network
stack early in the initrd but make it survive into the real system.
Existing distributions rename network-interfaces during the transition
from initrd into the real system. This, obviously, cannot affect
devices that are up and running (unless you also consider moving them
between network-namespaces). However, the network manager now has to
make sure its management engine for dormant devices will not run in
parallel to these renames. Particularly, when you offload operations
like DHCP into separate processes, these might setup their sockets
early, and thus have to resolve the device-name possibly running into
this race-condition.
By avoiding a call to resolve the device-name, we no longer depend on
the name and can run network setup of dormant devices in parallel to
the transition off the initrd. The SO_BINDTOIFINDEX ioctl plugs this
race.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling smp_call_ipl_cpu() from the IPL CPU, we will try to read
from pcpu_devices->lowcore. However, due to prefixing, that will result
in reading from absolute address 0 on that CPU. We have to go via the
actual lowcore instead.
This means that right now, we will read lc->nodat_stack == 0 and
therfore work on a very wrong stack.
This BUG essentially broke rebooting under QEMU TCG (which will report
a low address protection exception). And checking under KVM, it is
also broken under KVM. With 1 VCPU it can be easily triggered.
:/# echo 1 > /proc/sys/kernel/sysrq
:/# echo b > /proc/sysrq-trigger
[ 28.476745] sysrq: SysRq : Resetting
[ 28.476793] Kernel stack overflow.
[ 28.476817] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[ 28.476820] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[ 28.476826] Krnl PSW : 0400c00180000000 0000000000115c0c (pcpu_delegate+0x12c/0x140)
[ 28.476861] R:0 T:1 IO:0 EX:0 Key:0 M:0 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
[ 28.476863] Krnl GPRS: ffffffffffffffff 0000000000000000 000000000010dff8 0000000000000000
[ 28.476864] 0000000000000000 0000000000000000 0000000000ab7090 000003e0006efbf0
[ 28.476864] 000000000010dff8 0000000000000000 0000000000000000 0000000000000000
[ 28.476865] 000000007fffc000 0000000000730408 000003e0006efc58 0000000000000000
[ 28.476887] Krnl Code: 0000000000115bfe: 4170f000 la %r7,0(%r15)
[ 28.476887] 0000000000115c02: 41f0a000 la %r15,0(%r10)
[ 28.476887] #0000000000115c06: e370f0980024 stg %r7,152(%r15)
[ 28.476887] >0000000000115c0c: c0e5fffff86e brasl %r14,114ce8
[ 28.476887] 0000000000115c12: 41f07000 la %r15,0(%r7)
[ 28.476887] 0000000000115c16: a7f4ffa8 brc 15,115b66
[ 28.476887] 0000000000115c1a: 0707 bcr 0,%r7
[ 28.476887] 0000000000115c1c: 0707 bcr 0,%r7
[ 28.476901] Call Trace:
[ 28.476902] Last Breaking-Event-Address:
[ 28.476920] [<0000000000a01c4a>] arch_call_rest_init+0x22/0x80
[ 28.476927] Kernel panic - not syncing: Corrupt kernel stack, can't continue.
[ 28.476930] CPU: 0 PID: 424 Comm: sh Not tainted 5.0.0-rc1+ #13
[ 28.476932] Hardware name: IBM 2964 NE1 716 (KVM/Linux)
[ 28.476932] Call Trace:
Fixes: 2f859d0dad ("s390/smp: reduce size of struct pcpu")
Cc: stable@vger.kernel.org # 4.0+
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
While "s390/vdso: avoid 64-bit vdso mapping for compat tasks" fixed
64-bit vdso mapping for compat tasks under gdb it introduced another
problem. "compat_mm" flag is not inherited during fork and when
31-bit process forks a child (but does not perform exec) it ends up
with 64-bit vdso. To address that, init_new_context (which is called
during fork and exec) now initialize compat_mm based on thread TIF_31BIT
flag. Later compat_mm is adjusted in arch_setup_additional_pages, which
is called during exec.
Fixes: d1befa6582 ("s390/vdso: avoid 64-bit vdso mapping for compat tasks")
Reported-by: Stefan Liebler <stli@linux.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_rescan_cpus() is called without the device_hotplug_lock, which can lead
to a dedlock when a new CPU is found and immediately set online by a udev
rule.
This was observed on an older kernel version, where the cpu_hotplug_begin()
loop was still present, and it resulted in hanging chcpu and systemd-udev
processes. This specific deadlock will not show on current kernels. However,
there may be other possible deadlocks, and since smp_rescan_cpus() can still
trigger a CPU hotplug operation, the device_hotplug_lock should be held.
For reference, this was the deadlock with the old cpu_hotplug_begin() loop:
chcpu (rescan) systemd-udevd
echo 1 > /sys/../rescan
-> smp_rescan_cpus()
-> (*) get_online_cpus()
(increases refcount)
-> smp_add_present_cpu()
(new CPU found)
-> register_cpu()
-> device_add()
-> udev "add" event triggered -----------> udev rule sets CPU online
-> echo 1 > /sys/.../online
-> lock_device_hotplug_sysfs()
(this is missing in rescan path)
-> device_online()
-> (**) device_lock(new CPU dev)
-> cpu_up()
-> cpu_hotplug_begin()
(loops until refcount == 0)
-> deadlock with (*)
-> bus_probe_device()
-> device_attach()
-> device_lock(new CPU dev)
-> deadlock with (**)
Fix this by taking the device_hotplug_lock in the CPU rescan path.
Cc: <stable@vger.kernel.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ASCE of an mm_struct can be modified after a task has been created,
e.g. via crst_table_downgrade for a compat process. The active_mm logic
to avoid the switch_mm call if the next task is a kernel thread can
lead to a situation where switch_mm is called where 'prev == next' is
true but 'prev->context.asce == next->context.asce' is not.
This can lead to a situation where a CPU uses the outdated ASCE to run
a task. The result can be a crash, endless loops and really subtle
problem due to TLBs being created with an invalid ASCE.
Cc: stable@kernel.org # v3.15+
Fixes: 53e857f308 ("s390/mm,tlb: race of lazy TLB flush vs. recreation")
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Right now the early machine detection code check stsi 3.2.2 for "KVM"
and set MACHINE_IS_VM if this is different. As the console detection
uses diagnose 8 if MACHINE_IS_VM returns true this will crash Linux
early for any non z/VM system that sets a different value than KVM.
So instead of assuming z/VM, do not set any of MACHINE_IS_LPAR,
MACHINE_IS_VM, or MACHINE_IS_KVM.
CC: stable@vger.kernel.org
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not implement
mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I+r6
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
You do not have to use define ... endef for filechk_* rules.
For simple cases, the use of assignment looks cleaner, IMHO.
I updated the usage for scripts/Kbuild.include in case somebody
misunderstands the 'define ... endif' is the requirement.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
These comments are leftovers of commit fcc8487d47 ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
filechk_* rules often consist of multiple 'echo' lines. They must be
surrounded with { } or ( ) to work correctly. Otherwise, only the
string from the last 'echo' would be written into the target.
Let's take care of that in the 'filechk' in scripts/Kbuild.include
to clean up filechk_* rules.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, CONFIG_JUMP_LABEL just means "I _want_ to use jump label".
The jump label is controlled by HAVE_JUMP_LABEL, which is defined
like this:
#if defined(CC_HAVE_ASM_GOTO) && defined(CONFIG_JUMP_LABEL)
# define HAVE_JUMP_LABEL
#endif
We can improve this by testing 'asm goto' support in Kconfig, then
make JUMP_LABEL depend on CC_HAS_ASM_GOTO.
Ugly #ifdef HAVE_JUMP_LABEL will go away, and CONFIG_JUMP_LABEL will
match to the real kernel capability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When testing in userspace, UBSAN pointed out that shifting into the sign
bit is undefined behaviour. It doesn't really make sense to ask for the
highest set bit of a negative value, so just turn the argument type into
an unsigned int.
Some architectures (eg ppc) already had it declared as an unsigned int,
so I don't expect too many problems.
Link: http://lkml.kernel.org/r/20181105221117.31828-1-willy@infradead.org
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- A larger update for the zcrypt / AP bus code
+ Update two inline assemblies in the zcrypt driver to make gcc happy
+ Add a missing reply code for invalid special commands for zcrypt
+ Allow AP device reset to be triggered from user space
+ Split the AP scan function into smaller, more readable functions
- Updates for vfio-ccw and vfio-ap
+ Add maintainers and reviewer for vfio-ccw
+ Include facility.h in vfio_ap_drv.c to avoid fragile include chain
+ Simplicy vfio-ccw state machine
- Use the common code version of bust_spinlocks
- Make use of the DEFINE_SHOW_ATTRIBUTE
- Fix three incorrect file permissions in the DASD driver
- Remove bit spin-lock from the PCI interrupt handler
- Fix GFP_ATOMIC vs GFP_KERNEL in the PCI code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcLGoIAAoJEDjwexyKj9rgyN8IANaQvHbVBA3vz/Ssb6ZiR/K6
rTBoXjJQqyJ/cf6RZeFi1b4Douv4QWJw3s06KXbrdmK/ONm5rypXVfXlAhY71pg5
40BUb92MGXhJw6JFDQ50Udd6Z5r7r6RYR1puyg4tzHmBuNVL7FB5RqFm92UOkMOD
ZI03G1sfA6/1XUKhNfCfNBB6Jt6V+iAAex8bgrp09wAeoGnAO20oFuis9u7pLlNm
a5Cp9n7faXEN+qes1iBtVDr5o7opuhanwWKnhvsYTAbpOo7jGJ/47IPKT2Wfmurd
wkMZBEC+Ntk/IfkaBzp7azeISZD5EbucTcgo/I9nzq/aWeflfXXeYl7My0aQB48=
=Lqrh
-----END PGP SIGNATURE-----
Merge tag 's390-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- A larger update for the zcrypt / AP bus code:
+ Update two inline assemblies in the zcrypt driver to make gcc happy
+ Add a missing reply code for invalid special commands for zcrypt
+ Allow AP device reset to be triggered from user space
+ Split the AP scan function into smaller, more readable functions
- Updates for vfio-ccw and vfio-ap
+ Add maintainers and reviewer for vfio-ccw
+ Include facility.h in vfio_ap_drv.c to avoid fragile include chain
+ Simplicy vfio-ccw state machine
- Use the common code version of bust_spinlocks
- Make use of the DEFINE_SHOW_ATTRIBUTE
- Fix three incorrect file permissions in the DASD driver
- Remove bit spin-lock from the PCI interrupt handler
- Fix GFP_ATOMIC vs GFP_KERNEL in the PCI code
* tag 's390-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: rework ap scan bus code
s390/zcrypt: make sysfs reset attribute trigger queue reset
s390/pci: fix sleeping in atomic during hotplug
s390/pci: remove bit_lock usage in interrupt handler
s390/drivers: fix proc/debugfs file permissions
s390: convert to DEFINE_SHOW_ATTRIBUTE
MAINTAINERS/vfio-ccw: add Farhan and Eric, make Halil Reviewer
vfio: ccw: Merge BUSY and BOXED states
s390: use common bust_spinlocks()
s390/zcrypt: improve special ap message cmd handling
s390/ap: rework assembler functions to use unions for in/out register variables
s390: vfio-ap: include <asm/facility> for test_facility()
Pull seccomp updates from James Morris:
- Add SECCOMP_RET_USER_NOTIF
- seccomp fixes for sparse warnings and s390 build (Tycho)
* 'next-seccomp' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
seccomp, s390: fix build for syscall type change
seccomp: fix poor type promotion
samples: add an example of seccomp user trap
seccomp: add a return code to trap to userspace
seccomp: switch system call argument type to void *
seccomp: hoist struct seccomp_data recalculation higher
Set the flag to skip scanning for VFs after SR-IOV enablement. VF creation
will be triggered by the hotplug code.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries
by Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right Kconfig
files. This series instead just selects the presence (when needed) and
then handles everything in the bus-specific Kconfig file under drivers/.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WxId
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig file consolidation from Masahiro Yamada:
"Consolidation of bus (PCI, PCMCIA, EISA, RapidIO) config entries by
Christoph Hellwig.
Currently, every architecture that wants to provide common peripheral
busses needs to add some boilerplate code and include the right
Kconfig files. This series instead just selects the presence (when
needed) and then handles everything in the bus-specific Kconfig file
under drivers/"
* tag 'kconfig-v4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
pcmcia: remove per-arch PCMCIA config entry
eisa: consolidate EISA Kconfig entry in drivers/eisa
rapidio: consolidate RAPIDIO config entry in drivers/rapidio
pcmcia: allow PCMCIA support independent of the architecture
PCI: consolidate the PCI_SYSCALL symbol
PCI: consolidate the PCI_DOMAINS and PCI_DOMAINS_GENERIC config options
PCI: consolidate PCI config entry in drivers/pci
MIPS: remove the HT_PCI config option
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
Merge misc updates from Andrew Morton:
- large KASAN update to use arm's "software tag-based mode"
- a few misc things
- sh updates
- ocfs2 updates
- just about all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (167 commits)
kernel/fork.c: mark 'stack_vm_area' with __maybe_unused
memcg, oom: notify on oom killer invocation from the charge path
mm, swap: fix swapoff with KSM pages
include/linux/gfp.h: fix typo
mm/hmm: fix memremap.h, move dev_page_fault_t callback to hmm
hugetlbfs: Use i_mmap_rwsem to fix page fault/truncate race
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
memory_hotplug: add missing newlines to debugging output
mm: remove __hugepage_set_anon_rmap()
include/linux/vmstat.h: remove unused page state adjustment macro
mm/page_alloc.c: allow error injection
mm: migrate: drop unused argument of migrate_page_move_mapping()
blkdev: avoid migration stalls for blkdev pages
mm: migrate: provide buffer_migrate_page_norefs()
mm: migrate: move migrate_page_lock_buffers()
mm: migrate: lock buffers before migrate_page_move_mapping()
mm: migration: factor out code to compute expected number of page references
mm, page_alloc: enable pcpu_drain with zone capability
kmemleak: add config to select auto scan
mm/page_alloc.c: don't call kasan_free_pages() at deferred mem init
...
A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for architectures
that have devices that perform DMA that is not cache coherent. Based
on the existing arm64 implementation and also used for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel data
leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script.
-----BEGIN PGP SIGNATURE-----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=in72
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
"A huge update this time, but a lot of that is just consolidating or
removing code:
- provide a common DMA_MAPPING_ERROR definition and avoid indirect
calls for dma_map_* error checking
- use direct calls for the DMA direct mapping case, avoiding huge
retpoline overhead for high performance workloads
- merge the swiotlb dma_map_ops into dma-direct
- provide a generic remapping DMA consistent allocator for
architectures that have devices that perform DMA that is not cache
coherent. Based on the existing arm64 implementation and also used
for csky now.
- improve the dma-debug infrastructure, including dynamic allocation
of entries (Robin Murphy)
- default to providing chaining scatterlist everywhere, with opt-outs
for the few architectures (alpha, parisc, most arm32 variants) that
can't cope with it
- misc sparc32 dma-related cleanups
- remove the dma_mark_clean arch hook used by swiotlb on ia64 and
replace it with the generic noncoherent infrastructure
- fix the return type of dma_set_max_seg_size (Niklas Söderlund)
- move the dummy dma ops for not DMA capable devices from arm64 to
common code (Robin Murphy)
- ensure dma_alloc_coherent returns zeroed memory to avoid kernel
data leaks through userspace. We already did this for most common
architectures, but this ensures we do it everywhere.
dma_zalloc_coherent has been deprecated and can hopefully be
removed after -rc1 with a coccinelle script"
* tag 'dma-mapping-4.21' of git://git.infradead.org/users/hch/dma-mapping: (73 commits)
dma-mapping: fix inverted logic in dma_supported
dma-mapping: deprecate dma_zalloc_coherent
dma-mapping: zero memory returned from dma_alloc_*
sparc/iommu: fix ->map_sg return value
sparc/io-unit: fix ->map_sg return value
arm64: default to the direct mapping in get_arch_dma_ops
PCI: Remove unused attr variable in pci_dma_configure
ia64: only select ARCH_HAS_DMA_COHERENT_TO_PFN if swiotlb is enabled
dma-mapping: bypass indirect calls for dma-direct
vmd: use the proper dma_* APIs instead of direct methods calls
dma-direct: merge swiotlb_dma_ops into the dma_direct code
dma-direct: use dma_direct_map_page to implement dma_direct_map_sg
dma-direct: improve addressability error reporting
swiotlb: remove dma_mark_clean
swiotlb: remove SWIOTLB_MAP_ERROR
ACPI / scan: Refactor _CCA enforcement
dma-mapping: factor out dummy DMA ops
dma-mapping: always build the direct mapping code
dma-mapping: move dma_cache_sync out of line
dma-mapping: move various slow path functions out of line
...
Patch series "Do not touch pages in hot-remove path", v2.
This patchset aims for two things:
1) A better definition about offline and hot-remove stage
2) Solving bugs where we can access non-initialized pages
during hot-remove operations [2] [3].
This is achieved by moving all page/zone handling to the offline
stage, so we do not need to access pages when hot-removing memory.
[1] https://patchwork.kernel.org/cover/10691415/
[2] https://patchwork.kernel.org/patch/10547445/
[3] https://www.spinics.net/lists/linux-mm/msg161316.html
This patch (of 5):
This is a preparation for the following-up patches. The idea of passing
the nid is that it will allow us to get rid of the zone parameter
afterwards.
Link: http://lkml.kernel.org/r/20181127162005.15833-2-osalvador@suse.de
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
totalram_pages and totalhigh_pages are made static inline function.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/1542090790-21750-4-git-send-email-arunks@codeaurora.org
Signed-off-by: Arun KS <arunks@codeaurora.org>
Suggested-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With tag based KASAN mode the early shadow value is 0xff and not 0x00, so
this patch renames kasan_zero_(page|pte|pmd|pud|p4d) to
kasan_early_shadow_(page|pte|pmd|pud|p4d) to avoid confusion.
Link: http://lkml.kernel.org/r/3fed313280ebf4f88645f5b89ccbc066d320e177.1544099024.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Pull RCU updates from Ingo Molnar:
"The biggest RCU changes in this cycle were:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions to
their vanilla RCU counterparts. This series is a step towards
complete removal of the RCU-bh and RCU-sched update-side functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for rcutorture
testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein for a
bag-on-head-class bug.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (112 commits)
rcutorture: Don't do busted forward-progress testing
rcutorture: Use 100ms buckets for forward-progress callback histograms
rcutorture: Recover from OOM during forward-progress tests
rcutorture: Print forward-progress test age upon failure
rcutorture: Print time since GP end upon forward-progress failure
rcutorture: Print histogram of CB invocation at OOM time
rcutorture: Print GP age upon forward-progress failure
rcu: Print per-CPU callback counts for forward-progress failures
rcu: Account for nocb-CPU callback counts in RCU CPU stall warnings
rcutorture: Dump grace-period diagnostics upon forward-progress OOM
rcutorture: Prepare for asynchronous access to rcu_fwd_startat
torture: Remove unnecessary "ret" variables
rcutorture: Affinity forward-progress test to avoid housekeeping CPUs
rcutorture: Break up too-long rcu_torture_fwd_prog() function
rcutorture: Remove cbflood facility
torture: Bring any extra CPUs online during kernel startup
rcutorture: Add call_rcu() flooding forward-progress tests
rcutorture/formal: Replace synchronize_sched() with synchronize_rcu()
tools/kernel.h: Replace synchronize_sched() with synchronize_rcu()
net/decnet: Replace rcu_barrier_bh() with rcu_barrier()
...
single-stepping fixes, improved tracing, various timer and vGIC
fixes
* x86: Processor Tracing virtualization, STIBP support, some correctness fixes,
refactorings and splitting of vmx.c, use the Hyper-V range TLB flush hypercall,
reduce order of vcpu struct, WBNOINVD support, do not use -ftrace for __noclone
functions, nested guest support for PAUSE filtering on AMD, more Hyper-V
enlightenments (direct mode for synthetic timers)
* PPC: nested VFIO
* s390: bugfixes only this time
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcH0vFAAoJEL/70l94x66Dw/wH/2FZp1YOM5OgiJzgqnXyDbyf
dNEfWo472MtNiLsuf+ZAfJojVIu9cv7wtBfXNzW+75XZDfh/J88geHWNSiZDm3Fe
aM4MOnGG0yF3hQrRQyEHe4IFhGFNERax8Ccv+OL44md9CjYrIrsGkRD08qwb+gNh
P8T/3wJEKwUcVHA/1VHEIM8MlirxNENc78p6JKd/C7zb0emjGavdIpWFUMr3SNfs
CemabhJUuwOYtwjRInyx1y34FzYwW3Ejuc9a9UoZ+COahUfkuxHE8u+EQS7vLVF6
2VGVu5SA0PqgmLlGhHthxLqVgQYo+dB22cRnsLtXlUChtVAq8q9uu5sKzvqEzuE=
=b4Jx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- selftests improvements
- large PUD support for HugeTLB
- single-stepping fixes
- improved tracing
- various timer and vGIC fixes
x86:
- Processor Tracing virtualization
- STIBP support
- some correctness fixes
- refactorings and splitting of vmx.c
- use the Hyper-V range TLB flush hypercall
- reduce order of vcpu struct
- WBNOINVD support
- do not use -ftrace for __noclone functions
- nested guest support for PAUSE filtering on AMD
- more Hyper-V enlightenments (direct mode for synthetic timers)
PPC:
- nested VFIO
s390:
- bugfixes only this time"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: x86: Add CPUID support for new instruction WBNOINVD
kvm: selftests: ucall: fix exit mmio address guessing
Revert "compiler-gcc: disable -ftracer for __noclone functions"
KVM: VMX: Move VM-Enter + VM-Exit handling to non-inline sub-routines
KVM: VMX: Explicitly reference RCX as the vmx_vcpu pointer in asm blobs
KVM: x86: Use jmp to invoke kvm_spurious_fault() from .fixup
MAINTAINERS: Add arch/x86/kvm sub-directories to existing KVM/x86 entry
KVM/x86: Use SVM assembly instruction mnemonics instead of .byte streams
KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()
KVM/MMU: Flush tlb directly in kvm_set_pte_rmapp()
KVM/MMU: Move tlb flush in kvm_set_pte_rmapp() to kvm_mmu_notifier_change_pte()
KVM: Make kvm_set_spte_hva() return int
KVM: Replace old tlb flush function with new one to flush a specified range.
KVM/MMU: Add tlb flush with range helper function
KVM/VMX: Add hv tlb range flush support
x86/hyper-v: Add HvFlushGuestAddressList hypercall support
KVM: Add tlb_remote_flush_with_range callback in kvm_x86_ops
KVM: x86: Disable Intel PT when VMXON in L1 guest
KVM: x86: Set intercept for Intel PT MSRs read/write
KVM: x86: Implement Intel PT MSRs read/write emulation
...
In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC that
is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine() invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32 optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJcE4TmAAoJELescNyEwWM0Nr0H/iaU7/wQSzHyNXtZoImyKTul
Blu2ga4/EqUrTU7AVVfmkl/3NBILWlgQVpY6tH6EfXQuvnxqD7CizbHyLdyO+z0S
B5PsFUH2GLMNAi48AUNqGqkgb2knFbg+T+9IimijDBkKg1G/KhQnRg6bXX32mLJv
Une8oshUPBVJMsHN1AcQknzKariuoE3u0SgJ+eOZ9yA2ZwKxP4yy1SkDt3xQrtI0
lojeRjxcyjTP1oGRNZC+BWUtGOT35p7y6cGTnBd/4TlqBGz5wVAJUcdoxnZ6JYVR
O8+ob9zU+4I0+SKt80s7pTLqQiL9rxkKZ5joWK1pr1g9e0s5N5yoETXKFHgJYP8=
=sYdt
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 festive updates from Will Deacon:
"In the end, we ended up with quite a lot more than I expected:
- Support for ARMv8.3 Pointer Authentication in userspace (CRIU and
kernel-side support to come later)
- Support for per-thread stack canaries, pending an update to GCC
that is currently undergoing review
- Support for kexec_file_load(), which permits secure boot of a kexec
payload but also happens to improve the performance of kexec
dramatically because we can avoid the sucky purgatory code from
userspace. Kdump will come later (requires updates to libfdt).
- Optimisation of our dynamic CPU feature framework, so that all
detected features are enabled via a single stop_machine()
invocation
- KPTI whitelisting of Cortex-A CPUs unaffected by Meltdown, so that
they can benefit from global TLB entries when KASLR is not in use
- 52-bit virtual addressing for userspace (kernel remains 48-bit)
- Patch in LSE atomics for per-cpu atomic operations
- Custom preempt.h implementation to avoid unconditional calls to
preempt_schedule() from preempt_enable()
- Support for the new 'SB' Speculation Barrier instruction
- Vectorised implementation of XOR checksumming and CRC32
optimisations
- Workaround for Cortex-A76 erratum #1165522
- Improved compatibility with Clang/LLD
- Support for TX2 system PMUS for profiling the L3 cache and DMC
- Reflect read-only permissions in the linear map by default
- Ensure MMIO reads are ordered with subsequent calls to Xdelay()
- Initial support for memory hotplug
- Tweak the threshold when we invalidate the TLB by-ASID, so that
mremap() performance is improved for ranges spanning multiple PMDs.
- Minor refactoring and cleanups"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (125 commits)
arm64: kaslr: print PHYS_OFFSET in dump_kernel_offset()
arm64: sysreg: Use _BITUL() when defining register bits
arm64: cpufeature: Rework ptr auth hwcaps using multi_entry_cap_matches
arm64: cpufeature: Reduce number of pointer auth CPU caps from 6 to 4
arm64: docs: document pointer authentication
arm64: ptr auth: Move per-thread keys from thread_info to thread_struct
arm64: enable pointer authentication
arm64: add prctl control for resetting ptrauth keys
arm64: perf: strip PAC when unwinding userspace
arm64: expose user PAC bit positions via ptrace
arm64: add basic pointer authentication support
arm64/cpufeature: detect pointer authentication
arm64: Don't trap host pointer auth use to EL2
arm64/kvm: hide ptrauth from guests
arm64/kvm: consistently handle host HCR_EL2 flags
arm64: add pointer authentication register bits
arm64: add comments about EC exception levels
arm64: perf: Treat EXCLUDE_EL* bit definitions as unsigned
arm64: kpti: Whitelist Cortex-A CPUs that don't implement the CSV3 field
arm64: enable per-task stack canaries
...
The Kconfig lexer supports special characters such as '.' and '/' in
the parameter context. In my understanding, the reason is just to
support bare file paths in the source statement.
I do not see a good reason to complicate Kconfig for the room of
ambiguity.
The majority of code already surrounds file paths with double quotes,
and it makes sense since file paths are constant string literals.
Make it treewide consistent now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
If we want to map memory from the DMA allocator to userspace it must be
zeroed at allocation time to prevent stale data leaks. We already do
this on most common architectures, but some architectures don't do this
yet, fix them up, either by passing GFP_ZERO when we use the normal page
allocator or doing a manual memset otherwise.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Sam Ravnborg <sam@ravnborg.org> [sparc]
Just two small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=GVCX
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fixes for 4.21
Just two small fixes.
Relocate #define statement for kvm related kernel messages
before the include of printk to become effective.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Make sure the debug feature and its allocated resources get
released upon unsuccessful architecture initialization.
A related indication of the issue will be reported as kernel
message.
Signed-off-by: Michael Mueller <mimu@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20181130143215.69496-2-mimu@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
A recent patch landed in the security tree [1] that changed the type of the
seccomp syscall. Unfortunately, I didn't quite get every instance of the
forward declarations, and thus there is a build failure. Here's the last
one that I could find, for s390. It should go through the security tree,
although hopefully some s390 people can check and make sure it looks
reasonable?
The only oddity is the trailing semicolon; some lines around this patch
have it, and some lines don't. I've left this one as-is.
[1]: https://lore.kernel.org/lkml/20181212231630.GA31584@beast/T/#u
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Fixes: 6a21cc50f0 ("seccomp: add a return code to trap to userspace")
Signed-off-by: Kees Cook <keescook@chromium.org>
All architectures except for sparc64 use the dma-direct code in some
form, and even for sparc64 we had the discussion of a direct mapping
mode a while ago. In preparation for directly calling the direct
mapping code don't bother having it optionally but always build the
code in. This is a minor hardship for some powerpc and arm configs
that don't pull it in yet (although they should in a relase ot two),
and sparc64 which currently doesn't need it at all, but it will
reduce the ifdef mess we'd otherwise need significantly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
When triggered by pci hotplug (PEC 0x306) clp_get_state is called
with spinlocks held resulting in the following warning:
zpci: n/a: Event 0x306 reconfigured PCI function 0x0
BUG: sleeping function called from invalid context at mm/page_alloc.c:4324
in_atomic(): 1, irqs_disabled(): 0, pid: 98, name: kmcheck
2 locks held by kmcheck/98:
Change the allocation to use GFP_ATOMIC.
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The interrupt handler uses bit_spin_lock around a call to retrieve
per irq data (the irq number). However this per irq data is only
set during irq setup time and never changed until the irq is freed.
Thus it's safe to remove the lock usage.
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-11
The following pull-request contains BPF updates for your *net-next* tree.
It has three minor merge conflicts, resolutions:
1) tools/testing/selftests/bpf/test_verifier.c
Take first chunk with alignment_prevented_execution.
2) net/core/filter.c
[...]
case bpf_ctx_range_ptr(struct __sk_buff, flow_keys):
case bpf_ctx_range(struct __sk_buff, wire_len):
return false;
[...]
3) include/uapi/linux/bpf.h
Take the second chunk for the two cases each.
The main changes are:
1) Add support for BPF line info via BTF and extend libbpf as well
as bpftool's program dump to annotate output with BPF C code to
facilitate debugging and introspection, from Martin.
2) Add support for BPF_ALU | BPF_ARSH | BPF_{K,X} in interpreter
and all JIT backends, from Jiong.
3) Improve BPF test coverage on archs with no efficient unaligned
access by adding an "any alignment" flag to the BPF program load
to forcefully disable verifier alignment checks, from David.
4) Add a new bpf_prog_test_run_xattr() API to libbpf which allows for
proper use of BPF_PROG_TEST_RUN with data_out, from Lorenz.
5) Extend tc BPF programs to use a new __sk_buff field called wire_len
for more accurate accounting of packets going to wire, from Petar.
6) Improve bpftool to allow dumping the trace pipe from it and add
several improvements in bash completion and map/prog dump,
from Quentin.
7) Optimize arm64 BPF JIT to always emit movn/movk/movk sequence for
kernel addresses and add a dedicated BPF JIT backend allocator,
from Ard.
8) Add a BPF helper function for IR remotes to report mouse movements,
from Sean.
9) Various cleanups in BPF prog dump e.g. to make UAPI bpf_prog_info
member naming consistent with existing conventions, from Yonghong
and Song.
10) Misc cleanups and improvements in allowing to pass interface name
via cmdline for xdp1 BPF example, from Matteo.
11) Fix a potential segfault in BPF sample loader's kprobes handling,
from Daniel T.
12) Fix SPDX license in libbpf's README.rst, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PREEMPT_NEED_RESCHED is never used directly, so move it into the arch
code where it can potentially be implemented using either a different
bit in the preempt count or as an entirely separate entity.
Cc: Robert Love <rml@tech9.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
These days architectures are mostly out of the business of dealing with
struct scatterlist at all, unless they have architecture specific iommu
drivers. Replace the ARCH_HAS_SG_CHAIN symbol with a ARCH_NO_SG_CHAIN
one only enabled for architectures with horrible legacy iommu drivers
like alpha and parisc, and conditionally for arm which wants to keep it
disable for legacy platforms.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
S390 already returns (~(dma_addr_t)0x0) on mapping failures, so we can
switch over to returning DMA_MAPPING_ERROR and let the core dma-mapping
code handle the rest.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
