The driver is defining debugfs entries by calling
`adis16480_debugfs_init()`. However, those entries are attached to the
iio_dev debugfs entry which won't exist if no debugfs_reg_access
callback is provided.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the scales for the gyroscope, accelerometer and
barometer. The pressure scale was just wrong. For the others, the scale
factors were not taking into account that a 32bit word is being read
from the device.
Fixes: 7abad1063d ("iio: adis16480: Fix scale factors")
Fixes: 82e7a1b250 ("iio: imu: adis16480: Add support for ADIS1649x family of devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7292 is a 10-bit monitor and control system with ADC, DACs,
temperature sensor, and GPIOs.
Configure AD7292 devices in direct access mode, enabling single-ended
ADC readings.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7292.pdf
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MPU6050 has two power supply pins: VDD and VLOGIC, but the
mpu6050 driver only supports enabling one of them at the moment.
In some cases, they may need to be enabled separately.
Add an additional "vdd-supply" that stays enabled for as long as
the driver is loaded. We cannot turn off the VDD regulator during
suspend as this would cause register settings (FSR, sampling rate, ...)
to be lost.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Field was already set for light/proximity and
accelerometer/gyroscope/magnetometer sensors.
Fixes: ae7b02ad2f ("iio: common: cros_ec_sensors: Expose cros_ec_sensors frequency range via iio sysfs")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5600 is a single channel, 16-bit resolution, voltage output digital
to analog converter (DAC). The AD5600 uses a 3-wire SPI interface. It is
part of the AD5541 family of DACs.
The ad5446 IIO driver implements support for some of these DACs (in the
AD5441 family), so the change is a simple entry in this driver.
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/AD5600.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
veml6030 is an ambient light sensor from Vishay semiconductors.
It has 16-bit resolution, supports both ambient light measurement
and white channel which is more responsive to wider wavelength
spectrum. It has flexible power saving, integration time and
gain options. Communication with host is over I2C.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Express available frequencies in mHZ in order to support even
rational ODRs. This patch is need to fix an Android CTS failure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since st_lsm6dsx i2c master controller relies on accel device as trigger
and slave devices can run at different ODRs we must select an accel_odr >=
slave_odr. Report real accel ODR in st_lsm6dsx_check_odr() in order to
properly set sensor frequency in st_lsm6dsx_write_raw and avoid to
report unsupported frequency
Fixes: 6ffb55e500 ("iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce odr_len in st_lsm6dsx_odr_table_entry data structure in order
to explicitly define odr table size and support devices with different
odr table map
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new optional dt property to tune analog clock prescaler.
Driver looks for optional "st,max-clk-rate-hz", then computes
best approximation below that rate, using ADC internal prescaler.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce local boilerplate.
Suggested by coccinelle
CHECK drivers/iio/dac/vf610_dac.c
drivers/iio/dac/vf610_dac.c:189:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Reduce boilerplate.
Suggested by coccinelle
CHECK drivers/iio/dac/lpc18xx_dac.c
drivers/iio/dac/lpc18xx_dac.c:121:1-10: WARNING: Use devm_platform_ioremap_resource for dac -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
CC: Joachim Eastwood <manabian@gmail.com>
Reduces boilerplate.
Suggested by coccinelle
CHECK drivers/iio/adc/vf610_adc.c
drivers/iio/adc/vf610_adc.c:819:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Fugang Duan <b38611@freescale.com>
Avoids local boilerplate doing the same thing.
Suggested by coccinelle
CHECK drivers/iio/adc/spear_adc.c
drivers/iio/adc/spear_adc.c:283:1-22: WARNING: Use devm_platform_ioremap_resource for st -> adc_base_spear6xx
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Avoids some local boilerplate.
Suggested by coccinelle.
CHECK drivers/iio/adc/rcar-gyroadc.c
drivers/iio/adc/rcar-gyroadc.c:495:1-11: WARNING: Use devm_platform_ioremap_resource for priv -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Reduces local boilerplate code.
Suggested by coccinelle via coccicheck.
CHECK drivers/iio/adc/npcm_adc.c
drivers/iio/adc/npcm_adc.c:200:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Avoid local boilerplate.
Identified by coccinelle
CHECK drivers/iio/adc/lpc18xx_adc.c
drivers/iio/adc/lpc18xx_adc.c:137:1-10: WARNING: Use devm_platform_ioremap_resource for adc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Replaces local boilerplate. Identified by coccinelle.
CHECK drivers/iio/adc/ingenic-adc.c
drivers/iio/adc/ingenic-adc.c:449:1-10: WARNING: Use devm_platform_ioremap_resource for adc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Artur Rojek <contact@artur-rojek.eu>
Reduces local boilerplate.
Found by coccinelle:
drivers/iio/adc/cc10001_adc.c:344:1-18: WARNING: Use devm_platform_ioremap_resource for adc_dev -> reg_base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Naidu Tellapati <naidu.tellapati@imgtec.com>
Reduces boilerplate. Identified by coccinelle
CHECK drivers/iio/adc/mt6577_auxadc.c
drivers/iio/adc/mt6577_auxadc.c:257:1-18: WARNING: Use devm_platform_ioremap_resource for adc_dev -> reg_base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reduces boilerplate.
Identified by: Coccinelle / coccicheck
CHECK drivers/iio/adc/aspeed_adc.c
drivers/iio/adc/aspeed_adc.c:189:1-11: WARNING: Use devm_platform_ioremap_resource for data -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Rick Altherr <raltherr@google.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
This was also caught by the `-Wmaybe-uninitialized` warning, which
(ironically as-is) it makes quite a lot of sense to do for this.
The code that actually calls this function will fail to copy on
the uninitialized value. Hence, patch does not need to go into stable.
Fixes: 78026a6fde ("iio:imu:adis: Add debugfs register access support")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This was found only after the whole thing with the inline functions, but
the compiler actually found something. The value of the `bias` (in
adis16480_get_calibbias()) should only be set if the read operation was
successful.
No actual known problem occurs as users of this function all
ultimately check the return value. Hence probably not stable material.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a typical checkpatch warning. The change just renames the type of
the `freq` var to `unsigned int`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is just a minor indentation/alignment fix for the default case of a
switch statement.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS library functions return zero on success, and negative values for
error. Positive values aren't returned, but we only care about the success
value (which is zero).
This change is mostly needed so that the compiler won't make any inferences
about some about values being potentially un-initialized. This only
triggers after making some functions inline, because the compiler can
better follow return paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function and the iio_triggered_buffer_predisable() hook
should be called last in the predisable hook.
This change updates the driver to attach/detach the poll func in the
correct order.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function. The iio_triggered_buffer_predisable() hook is
called last (as is it should).
This change moves iio_triggered_buffer_postenable() to be called first. It
adds iio_triggered_buffer_predisable() on the error paths of the postenable
hook.
For the predisable hook, some code-paths have been changed to make sure
that the iio_triggered_buffer_predisable() hook gets called in case there
is an error before it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSRX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsrx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
None of the ST sensor drivers use any symbols from
<linux/gpio.h>, just drop the include from all of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set gain in hx711_reset() to its default value after a reset cycle. This
omits one precautionary read cycle, because the read is performed in
hx711_set_gain_for_channel() anyway if gain has changed.
Check for DOUT low and if its high wait some time if it goes down
instead of doing a blind reset cycle when DOUT is not down.
This is a performance optimization which allows to query the sensor with
a higher frequency.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the following warnings when documentation is built:
drivers/iio/adc/stm32-adc-core.c:62: warning: cannot understand function
prototype: 'struct stm32_adc_common_regs '
drivers/iio/adc/stm32-adc-core.c:78: warning: cannot understand function
prototype: 'struct stm32_adc_priv_cfg '
drivers/iio/adc/stm32-adc-core.c:123: warning: Function parameter or
member 'pdev' not described in 'stm32f4_adc_clk_sel'
drivers/iio/adc/stm32-adc.c:219: warning: cannot understand function
prototype: 'struct stm32_adc_regs '
drivers/iio/adc/stm32-adc.c:237: warning: cannot understand function
prototype: 'struct stm32_adc_regspec '
drivers/iio/adc/stm32-adc.c:264: warning: cannot understand function
prototype: 'struct stm32_adc_cfg '
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'difsel' not described in 'N'
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'pcsel' not described in 'stm32_adc'
drivers/iio/adc/stm32-adc.c:371: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_sq[STM32_ADC_MAX_SQ + 1]
drivers/iio/adc/stm32-adc.c:417: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:508: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32h7_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:1112: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_get_trig_extsel'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'reg' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'writeval' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'readval' not described in 'stm32_adc_debugfs_reg_access'
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.
The iio_triggered_buffer_postenable() should be called before (to attach
the poll func) and then the
The iio_triggered_buffer_predisable() function is hooked directly without
anything, which is probably fine, as the postenable() version seems to also
do some reset/wake-up of the device.
This will mean it will be easier when removing it; i.e. it just gets
removed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggestion from coccinelle / coccicheck
CHECK drivers/iio/adc/twl4030-madc.c
drivers/iio/adc/twl4030-madc.c:524:6-15: WARNING: Comparison of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:655:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:659:2-44: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:664:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:498:2-34: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:510:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:511:2-11: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:531:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:532:2-11: WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
The LTC2983 is a Multi-Sensor High Accuracy Digital Temperature
Measurement System. It measures a wide variety of temperature sensors and
digitally outputs the result, in °C or °F, with 0.1°C accuracy and
0.001°C resolution. It can measure the temperature of all standard
thermocouples (type B,E,J,K,N,S,R,T), standard 2-,3-,4-wire RTDs,
thermistors and diodes.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can drop some duplicate code if we use devm_action for disabling
regulators and pm and the managed variant of iio_device_register().
This allows us to completely remove all remove() callbacks from both
i2c and spi code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The vddd and vdda supplies are always operated on together. We can
shrink the code a bit by using the bulk regulator helpers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FXOS8700CQ is a small, low-power, 3-axis linear accelerometer and 3-axis
magnetometer combined into a single package. The device features a
selectable I2C or point-to-point SPI serial interface with 14-bit
accelerometer and 16-bit magnetometer ADC resolution along with
smart-embedded functions.
FXOS8700CQ has dynamically selectable accelerationfull-scale ranges of
±2 g/±4 g/±8 g and a fixed magnetic measurement range of ±1200 μT.
Output data rates (ODR) from 1.563 Hz to 800 Hz are selectable by the user
for each sensor. Interleaved magnetic and acceleration data is available
at ODR rates of up to 400 Hz. FXOS8700CQ is available in a plastic QFN
package and it is guaranteed to operate over the extended temperature
range of –40 °C to +85 °C.
TODO: Trigger and IRQ configuration support
Datasheet:
http://cache.freescale.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduces local boilerplate.
Suggested by coccinelle.
CHECK drivers/iio/adc/xilinx-xadc-core.c
drivers/iio/adc/xilinx-xadc-core.c:1184:1-11: WARNING: Use devm_platform_ioremap_resource for xadc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Manish Narani <manish.narani@xilinx.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Coccinelle noticed:
CHECK drivers/iio/adc/cpcap-adc.c
drivers/iio/adc/cpcap-adc.c:1009:9-34: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT
As far as I can see this is a simple case of it should be specified
but isn't.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Avoid local boilerplate.
Suggested by coccinelle via coccicheck.
CHECK drivers/iio/adc/meson_saradc.c
drivers/iio/adc/meson_saradc.c:1218:1-5: WARNING: Use devm_platform_ioremap_resource for base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce local boilerplate.
Identified by coccinelle
drivers/iio/adc/exynos_adc.c:792:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
