Stefan Richter <stefanr@s5r6.in-berlin.de> says:
| As far as I can tell, it would be best to ignore max_rec and sspd from ARP
| and NDP but keep using the respective information from firewire-core
| instead (handed over by fwnet_probe()).
|
| Why? As I noted earlier, RFC 2734:1999 and RFC 3146:2001 were apparently
| written with a too simplistic notion of IEEE 1394 bus topology, resulting
| in max_rec and sspd in ARP-1394 and NDP-1394 to be useless, IMO.
|
| Consider a bus like this:
|
| A ---- B ==== C
|
| A, B, C are all IP-over-1394 capable nodes. ---- is an S400 cable hop,
| and ==== is an S800 cable hop.
|
| In case of unicasts or multicasts in which node A is involved as
| transmitter or receiver, as well as in case of broadcasts, the speeds
| S100, S200, S400 work and speed S400 is optimal.
|
| In case of anything else, IOW in case of unicasts or multicasts in which
| only nodes B and C are involved, the speeds S100, S200, S400, S800 work
| and speed S800 is optimal.
|
| Clearly, node A should indicate sspd = S400 in its ARP or NDP packets.
| But which sspd should nodes B and C set there? Maybe they set S400, which
| would work but would waste half of the available bandwidth in the second
| case. Or maybe they set S800, which is OK in the second case but would
| prohibit any communication with node A if blindly taken for correct.
|
| On the other hand, firewire-core *always* gives us the correct and optimum
| peer-to-peer speed and asynchronous packet payload, no matter how simple
| or complex the bus topology is and no matter in which temporal order nodes
| join the bus and are discovered.
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate FIFO address before registering net_device.
This is preparation to change the pseudo hardware address format
for firewire devices to include the offset of the FIFO for receipt
of unicast datagrams, instead of mangling ARP/NDP messages in the
driver layer.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send L2 multicast packet via GASP (Global asynchronous stream packet) by
seeing the multicast bit in the L2 hardware address, not by seeing upper-
layer protocol address.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devres APIs where possible to simplify error handling
in driver probe.
While at it, also rename the goto targets in error path to
introduce some consistency in how they are named.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
Following patch series restructure GRE and IPIP tunneling code
to make it modular. It adds ip_tunnel module which acts as
generic tunneling layer which has common code.
These patches do not change any functionality.
v3:v4:
- Fixed compilation error in ipv6.
- Few coding style fixes.
v2-v3:
- Use GPL exports for all export symbols.
- Set default config NET_IP_TUNNEL to m.
v1-v2:
- Dropped patch to convert gre_proto_lock to rtnl lock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common function get calculate rtnl_link_stats64 stats.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use common ecn_encap functions from ip_tunnel module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes bug in VXLAN code where is iptunnel_xmit() called with NULL
dev->tstats.
This bug was introduced in commit 6aed0c8bf7 (tunnel: use
iptunnel_xmit() again).
Following patch fixes bug by setting dev->tstats. It uses ip_tunnel
module code to share stats function.
CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse common ip-tunneling code which is re-factored from GRE
module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch refactors GRE code into ip tunneling code and GRE
specific code. Common tunneling code is moved to ip_tunnel module.
ip_tunnel module is written as generic library which can be used
by different tunneling implementations.
ip_tunnel module contains following components:
- packet xmit and rcv generic code. xmit flow looks like
(gre_xmit/ipip_xmit)->ip_tunnel_xmit->ip_local_out.
- hash table of all devices.
- lookup for tunnel devices.
- control plane operations like device create, destroy, ioctl, netlink
operations code.
- registration for tunneling modules, like gre, ipip etc.
- define single pcpu_tstats dev->tstats.
- struct tnl_ptk_info added to pass parsed tunnel packet parameters.
ipip.h header is renamed to ip_tunnel.h
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip-header id needs to be incremented even if IP_DF flag is set.
This behaviour was changed in commit 490ab08127
(IP_GRE: Fix IP-Identification).
Following patch fixes it so that identification is always
incremented.
Reported-by: Cong Wang <amwang@redhat.com>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
This reverts commit d6a8c36dd6.
Next commit makes this commit unnecessary.
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 10c0d7ed32.
Next commit makes this commit unnecessary.
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have defined a sparse port allocation which is non-contiguous and
contains gaps, the code freeing port_names will just stop when it
encouters a first NULL port_names, which is not right, we should iterate
over all possible number of ports (DSA_MAX_PORTS) until we are done.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch factors the freeing of the struct dsa_platform_data
manipulated by the driver identically in two places to a single
function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree binding documentation for dsa explicitely states that a
DSA node should have its #address-cells property set to 2, yet the
example still used 1, fix that typo.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is never used.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is in fact counting the ring slots required for responses.
Separate the concepts of ring slots and skb frags make the code clearer, as
now netfront and netback can have different MAX_SKB_FRAGS, slot and frag are
not mapped 1:1 any more.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is supposed to hold reference to the last extra_info in the
loop. However there is only type of extra info here and the loop to process
extra info is missing, so this variable is never used and causes confusion.
Remove it at the moment. We can add it back when necessary.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_ptp.ko can't run individually
rename fec.c to fec_main.c
Build fec.o and fec_ptp.o into one fec.ko
Remove unnessary EXPORT_SYMBOL in fec_ptp
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter/IPVS updates for
your net-next tree, they are:
* Better performance in nfnetlink_queue by avoiding copy from the
packet to netlink message, from Eric Dumazet.
* Remove unnecessary locking in the exit path of ebt_ulog, from Gao Feng.
* Use new function ipv6_iface_scope_id in nf_ct_ipv6, from Hannes Frederic Sowa.
* A couple of sparse fixes for IPVS, from Julian Anastasov.
* Use xor hashing in nfnetlink_queue, as suggested by Eric Dumazet, from
myself.
* Allow to dump expectations per master conntrack via ctnetlink, from myself.
* A couple of cleanups to use PTR_RET in module init path, from Silviu-Mihai
Popescu.
* Remove nf_conntrack module a bit faster if netns are in use, from
Vladimir Davydov.
* Use checksum_partial in ip6t_NPT, from YOSHIFUJI Hideaki.
* Sparse fix for nf_conntrack, from Stephen Hemminger.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix memory leak and kmap leak at shutdown
- release IR DMA context already at ifdown rather than shutdown
(many controllers have got only 4 of them, so let's not hold it
longer than strictly necessary)
- misc startup/shutdown changes which prepare for later addition
of IPv6-over-1394 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=4S0t
-----END PGP SIGNATURE-----
Merge tag 'firewire-net-resource-mgt' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
firewire-net driver changes:
- fix memory leak and kmap leak at shutdown
- release IR DMA context already at ifdown rather than shutdown
(many controllers have got only 4 of them, so let's not hold it
longer than strictly necessary)
- misc startup/shutdown changes which prepare for later addition
of IPv6-over-1394 support
Signed-off-by: David S. Miller <davem@davemloft.net>
When neither IFF_BRIDGE nor IFF_BRIDGE_PORT is set,
and afspec == NULL but protinfo != NULL, we run into
"if (err == 0) br_ifinfo_notify(RTM_NEWLINK, p);" with
random value in ret.
Thanks to Sergei for pointing out the error in commit comments.
Signed-off-by: Hong Zhiguo <honkiko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for registering DSA switches using Device Tree
bindings. Note that we support programming the switch routing table even
though no in-tree user seems to require it. I tested this on Armada 370
with a Marvell 88E6172 (not supported by mainline yet).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello!
After patch 1 got accepted to net-next I will also send a patch to
netfilter-devel to make the corresponding changes to the netfilter
reassembly logic.
Thanks,
Hannes
-- >8 --
[PATCH 2/2] ipv6: implement RFC3168 5.3 (ecn protection) for ipv6 fragmentation handling
This patch also ensures that INET_ECN_CE is propagated if one fragment
had the codepoint set.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jesper Dangaard Brouer <jbrouer@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just moves some code arround to make the ip4_frag_ecn_table
and IPFRAG_ECN_* constants accessible from the other reassembly engines. I
also renamed ip4_frag_ecn_table to ip_frag_ecn_table.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jesper Dangaard Brouer <jbrouer@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a dev_addr_genid for IPv6. The goal is to use it, combined with
dev_base_seq to check if a change occurs during a netlink dump.
If a change is detected, the flag NLM_F_DUMP_INTR is set in the first message
after the dump was interrupted.
Note that only dump of unicast addresses is checked (multicast and anycast are
not checked).
Reported-by: Junwei Zhang <junwei.zhang@6wind.com>
Reported-by: Hongjun Li <hongjun.li@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes benefit of dev_addr_genid and dev_base_seq to check if a change
occurs during a netlink dump. If a change is detected, the flag NLM_F_DUMP_INTR
is set in the first message after the dump was interrupted.
Note that seq and prev_seq must be reset between each family in rtnl_dump_all()
because they are specific to each family.
Reported-by: Junwei Zhang <junwei.zhang@6wind.com>
Reported-by: Hongjun Li <hongjun.li@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both the Marvell MV643XX ethernet driver and the Orion MDIO driver
are compiled as modules, the ethernet driver may be probed before the
MDIO driver. Let mv643xx_eth_probe() return EPROBE_DEFER in this case,
i.e. when it cannot find the PHY.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvmdio driver can be instantiated using device tree or as a classic
platform device. In order to load the driver automatically by udev in
the latter case, the driver needs to define a module alias for the
platform device.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cut and paste typo. We call ->ref() a second time instead
of ->deref().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to be a follow-up for a patch originally submitted under
the title "ioat: Do not enable DCA if tag map is invalid". It was brought to
my attention that the preferred approach for BIOS workarounds is to set the
taint flag for TAINT_FIRMWARE_WORKAROUND for systems that require BIOS
workarounds.
This change makes it so that the DCA workarounds for broken BIOSes will now
use WARN_TAINT_ONCE(1, TAINT_FIRMWARE_WORKAROUND, ...) instead of just
printing a message via dev_err.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull to get the thermal netlink multicast group name fix, otherwise
the assertion added in net-next to netlink to detect that kind of bug
makes systems unbootable for some folks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise build fails with CONFIG_DECNET && !CONFIG_DECNET_ROUTER
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When interface is down, mailbox command to get context statistics
fails. So restrict driver from issuing get statistics command when
interface is down.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 83xx adapter does not support MSI interrupts, display
warning whenever module parameter is used to load driver
in MSI mode.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Due to improper data type of variable "type", interrupt resources were
not getting deleted in hardware which was causing resource exhaustion
in hardware. Hence mailbox command fails after some iterations of context change.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A long standing problem with TSO is the fact that tcp_tso_should_defer()
rearms the deferred timer, while it should not.
Current code leads to following bad bursty behavior :
20:11:24.484333 IP A > B: . 297161:316921(19760) ack 1 win 119
20:11:24.484337 IP B > A: . ack 263721 win 1117
20:11:24.485086 IP B > A: . ack 265241 win 1117
20:11:24.485925 IP B > A: . ack 266761 win 1117
20:11:24.486759 IP B > A: . ack 268281 win 1117
20:11:24.487594 IP B > A: . ack 269801 win 1117
20:11:24.488430 IP B > A: . ack 271321 win 1117
20:11:24.489267 IP B > A: . ack 272841 win 1117
20:11:24.490104 IP B > A: . ack 274361 win 1117
20:11:24.490939 IP B > A: . ack 275881 win 1117
20:11:24.491775 IP B > A: . ack 277401 win 1117
20:11:24.491784 IP A > B: . 316921:332881(15960) ack 1 win 119
20:11:24.492620 IP B > A: . ack 278921 win 1117
20:11:24.493448 IP B > A: . ack 280441 win 1117
20:11:24.494286 IP B > A: . ack 281961 win 1117
20:11:24.495122 IP B > A: . ack 283481 win 1117
20:11:24.495958 IP B > A: . ack 285001 win 1117
20:11:24.496791 IP B > A: . ack 286521 win 1117
20:11:24.497628 IP B > A: . ack 288041 win 1117
20:11:24.498459 IP B > A: . ack 289561 win 1117
20:11:24.499296 IP B > A: . ack 291081 win 1117
20:11:24.500133 IP B > A: . ack 292601 win 1117
20:11:24.500970 IP B > A: . ack 294121 win 1117
20:11:24.501388 IP B > A: . ack 295641 win 1117
20:11:24.501398 IP A > B: . 332881:351881(19000) ack 1 win 119
While the expected behavior is more like :
20:19:49.259620 IP A > B: . 197601:202161(4560) ack 1 win 119
20:19:49.260446 IP B > A: . ack 154281 win 1212
20:19:49.261282 IP B > A: . ack 155801 win 1212
20:19:49.262125 IP B > A: . ack 157321 win 1212
20:19:49.262136 IP A > B: . 202161:206721(4560) ack 1 win 119
20:19:49.262958 IP B > A: . ack 158841 win 1212
20:19:49.263795 IP B > A: . ack 160361 win 1212
20:19:49.264628 IP B > A: . ack 161881 win 1212
20:19:49.264637 IP A > B: . 206721:211281(4560) ack 1 win 119
20:19:49.265465 IP B > A: . ack 163401 win 1212
20:19:49.265886 IP B > A: . ack 164921 win 1212
20:19:49.266722 IP B > A: . ack 166441 win 1212
20:19:49.266732 IP A > B: . 211281:215841(4560) ack 1 win 119
20:19:49.267559 IP B > A: . ack 167961 win 1212
20:19:49.268394 IP B > A: . ack 169481 win 1212
20:19:49.269232 IP B > A: . ack 171001 win 1212
20:19:49.269241 IP A > B: . 215841:221161(5320) ack 1 win 119
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With decnet converted, we can finally get rid of rta_buf and its
computations around it. It also gets rid of the minimal header
length verification since all message handlers do that explicitly
anyway.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
decnet is the only subsystem left that is relying on the global
netlink attribute buffer rta_buf. It's horrible design and we
want to get rid of it.
This converts all of decnet to do implicit attribute parsing. It
also gets rid of the error prone struct dn_kern_rta.
Yes, the fib_magic() stuff is not pretty.
It's compiled tested but I need someone with appropriate hardware
to test the patch since I don't have access to it.
Cc: linux-decnet-user@lists.sourceforge.net
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
This patch converts the mv643xx_eth driver to use the mvmdio MDIO bus driver
instead of rolling its own implementation. As a result, all users of this
mv643xx_eth driver are converted to register an "orion-mdio" platform_device.
The mvmdio driver is also updated to support an interrupt line which reports
SMI error/completion, and to allow traditionnal platform device registration
instead of just device tree.
David, I think it makes sense for you to merge all of this, since we do
not want the architecture files to be desynchronized from the mv643xx_eth to
avoid runtime breakage. The potential for merge conflicts should be very small.
====================
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the Marvell MV643XX ethernet driver to use the
Marvell Orion MDIO driver. As a result, PowerPC and ARM platforms
registering the Marvell MV643XX ethernet driver are also updated to
register a Marvell Orion MDIO driver. This driver voluntarily overlaps
with the Marvell Ethernet shared registers because it will use a subset
of this shared register (shared_base + 0x4 to shared_base + 0x84). The
Ethernet driver is also updated to look up for a PHY device using the
Orion MDIO bus driver.
For ARM and PowerPC we register a single instance of the "mvmdio" driver
in the system like it used to be done with the use of the "shared_smi"
platform_data cookie on ARM.
Note that it is safe to register the mvmdio driver only for the "ge00"
instance of the driver because this "ge00" interface is guaranteed to
always be explicitely registered by consumers of
arch/arm/plat-orion/common.c and other instances (ge01, ge10 and ge11)
were all pointing their shared_smi to ge00. For PowerPC the in-tree
Device Tree Source files mention only one MV643XX ethernet MAC instance
so the MDIO bus driver is registered only when id == 0.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the "mvmdio" to support a SMI error/done interrupt
line which can be used along with a wait queue instead of doing
busy-waiting on the registers. This is a feature which is available in
the mv643xx_eth SMI code and thus reduces again the gap between the two.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the base register cookie in the mvmdio drive from
"smireg" to "regs" since a subsequent patch is going to use an ioremap()
cookie whose size is larger than a single register of 4 bytes. No
functionnal code change introduced.
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the mvmdio driver not to use device tree
helper functions such as of_mdiobus_register() and of_iomap() so we can
instantiate this driver using a classic platform_device approach. Use
the device manager helper to ioremap() the base register cookie so we
get automatic freeing upon error and removal. This change is harmless
for Device Tree platforms because they will get the driver be registered
the same way as it was before.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
