gcc 7.1 complains that the driver uses sprintf() and thus does not validate
the length of output buffers.
drivers/hwmon/applesmc.c: In function 'applesmc_show_fan_position':
drivers/hwmon/applesmc.c:82:21: warning:
'%d' directive writing between 1 and 5 bytes into a region of size 4
Fix the problem by using scnprintf() instead of sprintf() throughout the
driver. Also explicitly limit the number of supported fans to avoid actual
buffer overruns and thus invalid keys.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The reference driver polled but mentioned it was possible to sleep
for a computed period to know when it's ready to read. However, polling
with minimal sleeps is quick and works. This also improves responsiveness
from the driver.
Testing: tested on ast2400 on quanta-q71l
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reduce the fan_tach period such that the fan controller uses a shorter
period to measure the rpm.
The original period of 0x1000 was chosen as a conversative value from the
reference implementation. Through experimentation on the quanta-q71l
board, I was able to drive the number down which ultimately reduced the
time the controller would use to determine the fan_tach. This value was
recently tested and accepted downstream on the IBM Zaius board which uses
the ast2500.
Future work: It may be worthwhile as this is a tunable parameter to the
system, to allow overriding it through the device tree.
Testing: Tested on an ast2400 sitting on a quanta-q71l and ast2500 on
power9.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch exports current(A) sensors in inband sensors copied to
main memory by OCC.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Today, the type of a PowerNV sensor system is determined with the
"compatible" property for legacy Firmwares and with the "sensor-type"
for newer ones. The same array of strings is used for both to do the
matching and this raises some issue to introduce new sensor types.
Let's introduce two different arrays (legacy and current) to make
things easier for new sensor types.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The implementation details for SCPI seems to suggest that the sensor
readings must be reported by SCP using a well defined scale
(millidegree Celsius for temperature, millivolts for voltage,
milliamperes for current, microwatts for power and microjoules for
energy).
This is also important for the interaction with other subsystems: for
example both the thermal sub-system and the hwmon sysfs interface expect
the temperature expressed in millidegree Celsius.
Unfortunately since this behaviour is dependent on the firmware
implementation there are cases where the sensor readings are reported
using a different scale. For example in the Amlogic SoCs the
temperature is reported in degree and not millidegree Celsius.
To take into account this discrepancy and fixup the values reported by
SCP a new compatible 'amlogic,meson-gxbb-scpi-sensors' is introduced and
used in this patch by the scpi-hwmon driver to convert the sensor
readings to the expected scale.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The aspeed-pwm-tacho controller supports measuring the fan tach by using
leading, falling, or both edges. This change allows the driver to
support either of the three configurations and will appropriately modify
the returned tach data.
If the controller is measuring with both edges it can return a value more
quickly to the requestor. This version of the driver should still take ~1s
to return with an RPM value per fan, however, it can be tuned faster with
double edge counting enabled than without.
I tested this and found the number returned matched what I expected.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
OCC provides historical minimum and maximum value for the sensor
readings. This patch exports them as highest and lowest attributes
for the inband sensors copied by OCC to main memory.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When enabled temperature smoothing allows ramping the fan speed over a
configurable period of time instead of jumping to the new speed
instantaneously.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Systems using 4-wire fans usually require high frequency (22.5kHz)
output on the pwm. Add 22500 as a valid option in the pwmfreq_table. In
high frequency mode the low-order bit are ignored so they can safely be
set to 0.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default adt7475 will stop the fans (pwm duty cycle 0%) when the
temperature drops past Tmin - hysteresis. Some systems want to keep the
fans moving even when the temperature drops so add new sysfs attributes
that configure the enhanced acoustics min 1-3 which allows the fans to
run at the minimum configure pwm duty cycle.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475 has had find_nearest() since it's creation in 2009. Since
then find_closest() has been introduced and several drivers have been
updated to use it. Update the adt7475 to use find_closest() and remove
the now unused find_nearest().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IR35221 is a Digital DC-DC Multiphase Converter
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
[groeck: Preserve alphabetic order in Kconfig;
add missing break statements (from Dan Carpenter);
add missing error checks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recent chips support multiple pins for fan speed inputs and fan control
outputs. Examine all of them to determine supported fan controls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of checking if a temperature source has a label, use a bit mask
to determine if a temperature source is valid for a given chip.
This simplifies the code and, if necessary, lets us support chips with
unknown or incomplete labels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make fan and pwm names in sysfs start with index 1 in accordance to
Documentation/hwmon/sysfs-interface conventions.
Current implementation starts with index 0, making tools such as
sensors(1) skip the first fan.
Signed-off-by: Stefan Schaeckeler <sschaeck@cisco.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Call of_node_put() on a node claimed with of_node_get() or by any other
means such as for_each_child_of_node().
Signed-off-by: Stefan Schaeckeler <sschaeck@cisco.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When the controller fails to provide an RPM reading within the alloted
time; the driver returns -ETIMEDOUT and no file contents.
Signed-off-by: Patrick Venture <venture@google.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver uses regmap and thus has to select it to avoid build
errors such as the following.
drivers/hwmon/aspeed-pwm-tacho.c:337:21: error: variable
'aspeed_pwm_tacho_regmap_config' has initializer but incomplete type
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The recent conversion to the hotplug state machine missed that the original
hotplug notifiers did not execute in the frozen state, which is used on
suspend on resume.
This does not matter on single socket machines, but on multi socket systems
this breaks when the device for a non-boot socket is removed when the last
CPU of that socket is brought offline. The device removal locks up the
machine hard w/o any debug output.
Prevent executing the hotplug callbacks when cpuhp_tasks_frozen is true.
Thanks to Tommi for providing debug information patiently while I failed to
spot the obvious.
Fixes: e00ca5df37 ("hwmon: (coretemp) Convert to hotplug state machine")
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver is no longer needed:
* It has no mainline users
* It has no DT support and OMAP is DT only
* iio-hwmon can be used for madc, which also works with DT
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7475 and ADT7476 have the STRT bit cleared by default[1]. Before any
monitoring activities the STRT bit needs to be set. Logically this needs
to happen before any of the sensors are read so the probe() function
seems the best place for it.
[1] - https://www.onsemi.com/pub/Collateral/ADT7475-D.PDF
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt voltage and current registers are signed 16-bit values so
handle them as such.
Signed-off-by: Joe Schaack <jschaack@xes-inc.com>
Reviewed-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C device ID entries set a .driver_data but this data is never
looked up by the driver. So don't set it and also remove the enum.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports.
The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer
inputs.
The device driver matches on the device tree node. The configuration
values are read from the device tree and written to the respective
registers.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value (ranging from 0 to 100 percent) and read
the fan tach rpm value.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently there is no method for setting the channel
value from the DTS file. When, the driver uses a dts
file to initialize the driver platform_data is not set.
As a result channel variable may not be set correctly.
Without the channel variable set correctly, some of the
sensors will not be initialized correctly. For example
temp3 sensor sysfs entries.
This implements the schema agreed with the device tree
binding document.
Signed-off-by: Mahoda Ratnayaka <mahoda.ratnayaka@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding the ability for the ads7828 and ads7830 to use device tree to
get optional parameters instead of using platform devices. This allows
people using custom boards to also use the ads7828 in a non-default manner.
Signed-off-by: Sam Povilus <kernel.development@povil.us>
[groeck: Fixed whitespace errors in ads7828.txt]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was reported that dell-smm-hwmon is working fine on Dell XPS 15 9560.
Link: http://www.spinics.net/lists/platform-driver-x86/msg10751.html
Reported-by: Vasile Dumitrescu <vasile.dumitrescu@undeva.eu>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The read_string callback is supposed to retrieve a pointer to a
constant string.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
