If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds netif_carrier_off before change speed and
duplex in ethtool_ops.set_link_ksettings, and adds
netif_carrier_on after complete the change.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds the code for waiting chip to clean the all
pkts(TX & RX) in chip when the driver uses the function named
"adjust link".
This patch cleans the pkts as follows:
1) close rx of chip, close tx of protocol stack.
2) wait rcb, ppe, mac to clean.
3) adjust link
4) open rx of chip, open tx of protocol stack.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have two Ethernet adapters:
r8169 0000:03:01.0 eth0: RTL8169sb/8110sb, 00:14:d1:14:2d:49, XID 10000000, IRQ 18
r8169 0000:01:00.0 eth0: RTL8168e/8111e, 64:66:b3:11:14:5d, XID 2c200000, IRQ 30
And after upgrading from linux 4.15 [1] to linux 4.18+ [2] RTL8169sb failed to
receive any packets. tcpdump shows a lot of checksum mismatch.
[1]: a0f79386a4
[2]: 0519359784 (4.19 merge window opened)
I started bisecting and the found that [3] breaks it. According to [4]:
"For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled."
So I moved rtl_init_rxcfg() after enabling tx/rs and now my adapter works
(RTL8168e works too).
[3]: 3559d81e76
[4]: e542a2269f ("r8169: adjust the RxConfig
settings.")
Also drop "rx" from rtl_set_rx_tx_config_registers(), since it does nothing
with it already.
Fixes: 3559d81e76 ("r8169: simplify
rtl_hw_start_8169")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Azat Khuzhin <a3at.mail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4ae0169fd1.
This change in the handling of the coalesce timer is causing regression on
(at least) amlogic platforms.
Network will break down very quickly (a few seconds) after starting
a download. This can easily be reproduced using iperf3 for example.
The problem has been reported on the S805, S905, S912 and A113 SoCs
(Realtek and Micrel PHYs) and it is likely impacting all Amlogics
platforms using Gbit ethernet
No problem was seen with the platform using 10/100 only PHYs (GXL internal)
Reverting change brings things back to normal and allows to use network
again until we better understand the problem with the coalesce timer.
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User controls @idx which to be used as index of hwsim_world_regdom_custom.
So, It can be exploited via Spectre-like attack. (speculative execution)
This kind of attack leaks address of hwsim_world_regdom_custom,
It leads an attacker to bypass security mechanism such as KASLR.
So sanitize @idx before using it to prevent attack.
I leveraged strategy [1] to find and exploit this gadget.
[1] https://github.com/jinb-park/linux-exploit/tree/master/exploit-remaining-spectre-gadget/
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
[johannes: unwrap URL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.
This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mac80211_hwsim driver intends to say that it supports up to four
STBC receive streams, but instead it ends up saying something undefined.
The IEEE80211_VHT_CAP_RXSTBC_X macros aren't independent bits that can
be ORed together, but values. In this case, _4 is the appropriate one
to use.
Signed-off-by: Danek Duvall <duvall@comfychair.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.
2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
Wang.
3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
Borkmann.
4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
attackers using it as a side-channel. From Eric Dumazet.
5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.
6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
Liu.
7) hns and hns3 bug fixes from Huazhong Tan.
8) Fix RIF leak in mlxsw driver, from Ido Schimmel.
9) iova range check fix in vhost, from Jason Wang.
10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.
11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.
12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.
13) TCP BBR congestion control fixes from Kevin Yang.
14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.
15) qed driver fixes from Tomer Tayar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: sched: Fix memory exposure from short TCA_U32_SEL
qed: fix spelling mistake "comparsion" -> "comparison"
vhost: correctly check the iova range when waking virtqueue
qlge: Fix netdev features configuration.
net: macb: do not disable MDIO bus at open/close time
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
i40e: fix condition of WARN_ONCE for stat strings
i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
ixgbe: fix driver behaviour after issuing VFLR
ixgbe: Prevent unsupported configurations with XDP
ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
igb: Use an advanced ctx descriptor for launchtime
e1000: ensure to free old tx/rx rings in set_ringparam()
e1000: check on netif_running() before calling e1000_up()
ixgb: use dma_zalloc_coherent instead of allocator/memset
ice: Trivial formatting fixes
...
Trivial fix to spelling mistake in DP_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes: 6c36a70744 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bde4975310.
All legacy clock implementations now implement clk_set_rate() (Some
implementations may be dummies, though).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 739de9a156 ("net: macb: Reorganize macb_mii bringup") broke
initializing macb on the EVB-KSZ9477 eval board.
There, of_mdiobus_register was called even for the fixed-link representing
the RGMII-link to the switch with the result that the driver attempts to
enumerate PHYs on a non-existent MDIO bus:
libphy: MACB_mii_bus: probed
mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0
[snip]
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31
The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO,
and calling of_phy_register_fixed_link later on fails because it tries
to claim the same GPIO:
macb f0028000.ethernet: broken fixed-link specification
Fix this by registering the fixed-link before calling mdiobus_register.
Fixes: 739de9a156 ("net: macb: Reorganize macb_mii bringup")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b10df596b ("i40e: use WARN_ONCE to replace the commented
BUG_ON size check") introduced a warning check to make sure
that the size of the stat strings was always the expected value. This
code accidentally inverted the check of the data pointer. Fix this so
that we accurately count the size of the stats we copied in.
This fixes an erroneous WARN kernel splat that occurs when requesting
ethtool statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If interface is connected to switch port configured for DCB there are
TX timeouts when bringing up interface. Problem started appearing after
adding in i40e driver code mqprio hardware offload mode. In function
i40e_vsi_configure_bw_alloc was added resetting BW rate which should
be executing when mqprio qdisc is removed but was also when there was
no mqprio qdisc added and DCB was enabled. In this patch was added
additional check for DCB flag so now when DCB is enabled the correct
DCB configs from before mqprio patch are restored.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since VFLR doesn't clear VFMBMEM (VF Mailbox Memory)
and is not re-enabling queues correctly we should fix
this behavior.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes address comments by Jakub Kicinski on
commit 38b7e7f8ae ("ixgbe: Do not allow LRO or MTU change with XDP").
Change the MTU check with XDP to allow any supported value and only
reject those outside of the range as opposed to rejecting any change
when XDP is active. In situations where MTU size is not supported,
return -EINVAL instead of -EPERM.
Add checks when enabling SRIOV, DCB, or adding L2FW offloaded device
as they are not supported with XDP.
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_fcoe_ddp_setup(), ixgbe_setup_fcoe_ddp_resources() and
ixgbe_sw_init() are never called in atomic context.
They call kmalloc(), dma_pool_alloc() and kzalloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_integrated_phy_loopback() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_sw_init() is never called in atomic context.
It calls kzalloc() and kcalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On i210, Launchtime (TxTime) requires the usage of an "Advanced
Transmit Context Descriptor" for retrieving the timestamp of a packet.
The igb driver correctly builds such descriptor on the segmentation
flow (i.e. igb_tso()) or on the checksum one (i.e. igb_tx_csum()), but the
feature is broken for AF_PACKET if the IGB_TX_FLAGS_VLAN is not set,
which happens due to an early return on igb_tx_csum().
This flag is only set by the kernel when a VLAN interface is used,
thus we can't just rely on it. Here we are fixing this issue by checking
if launchtime is enabled for the current tx_ring before performing the
early return.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL
-----BEGIN PGP SIGNATURE-----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=ACVk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 32-bit SoC platform updates from Olof Johansson:
"Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (112 commits)
ARM: uniphier: select RESET_CONTROLLER
arm64: uniphier: select RESET_CONTROLLER
ARM: uniphier: remove empty Makefile
ARM: exynos: Clear global variable on init error path
ARM: exynos: Remove outdated maintainer information
ARM: shmobile: Always enable ARCH_TIMER on SoCs with A7 and/or A15
ARM: shmobile: r8a7779: hide unused r8a7779_platform_cpu_kill
soc: r9a06g032: don't build SMP files for non-SMP config
ARM: shmobile: Add the R9A06G032 SMP enabler driver
ARM: at91: pm: configure wakeup sources for ULP1 mode
ARM: at91: pm: add PMC fast startup registers defines
ARM: at91: pm: Add ULP1 mode support
ARM: at91: pm: Use ULP0 naming instead of slow clock
ARM: hisi: handle of_iomap and fix missing of_node_put
ARM: hisi: check of_iomap and fix missing of_node_put
ARM: hisi: fix error handling and missing of_node_put
ARM: mx5: Set the DBGEN bit in ARM_GPC register
ARM: imx51: Configure M4IF to avoid visual artifacts
ARM: imx: call imx6sx_cpuidle_init() conditionally for 6sll
ARM: imx: fix i.MX6SLL build
...
1) Add missing "\n" when printing link event error message.
2) Update dev_err statement in probe.
3) Add function description for ice_clear_pf_cfg.
4) Fix coding style for ice_acquire_nvm.
5) netdev->mtu is unsigned so use %u.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_vsi_setup_[tx|rx]_rings, err is uninitialized which can result in
a garbage value return to the caller. Fix that.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) When ice_ena_msix_range() fails to reserve vectors, a devm_kfree()
warning was seen in the error flow path. So check pf->irq_tracker
before use in ice_clear_interrupt_scheme().
2) In ice_vsi_cfg(), check vsi->netdev before use.
3) In ice_get_link_status, check link_up before use.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the following interrupt causes that are not applicable or not
handled:
- PFINT_OICR_HLP_RDY_M
- PFINT_OICR_CPM_RDY_M
- PFINT_OICR_GPIO_M
- PFINT_OICR_STORM_DETECT_M
Add the following interrupt cause that's actually handled in ice_misc_intr:
- PFINT_OICR_PE_CRITERR_M
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the struct ice_aqc_vsi_props the field port_vlan_flags is an
overloaded term because it is used for both port VLANs (PVLANs) and
regular VLANs. This is an issue and is very confusing especially when
dealing with VFs because normal VLANs and port VLANs are not the same.
To fix this the field was renamed to vlan_flags and all of the #define's
labeled *_PVLAN_* were renamed to *_VLAN_* if they are not specific to
port VLANs.
Also in ice_vsi_manage_vlan_stripping, set the ICE_AQ_VSI_VLAN_MODE_ALL
bit to allow the driver to add a VLAN tag to all packets it sends.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we use a combination of ilog2 and is_power_of_2() to
calculate the next power of 2 for the qcount. This appears to be causing
a warning on some combinations of GCC and the Linux kernel:
MODPOST 1 modules
WARNING: "____ilog2_NaN" [ice.ko] undefined!
This appears to because because GCC realizes that qcount could be zero
in some circumstances and thus attempts to link against the
intentionally undefined ___ilog2_NaN function.
The order_base_2 function is intentionally defined to return 0 when
passed 0 as an argument, and thus will be safe to use here.
This not only fixes the warning but makes the resulting code slightly
cleaner, and is really what we should have used originally.
Also update the comment to make it more clear that we are rounding up,
not just incrementing the ilog2 of qcount unconditionally.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a consolidation of multiple bug fixes for control queue
processing.
1) In ice_clean_adminq_subtask() remove unnecessary reads/writes to
registers. The bits PFINT_FW_CTL, PFINT_MBX_CTL and PFINT_SB_CTL
are not set when an interrupt arrives, which means that clearing them
again can be omitted.
2) Get an accurate value in "pending" by re-reading the control queue
head register from the hardware.
3) Fix a corner case involving lost control queue messages by checking
for new control messages (using ice_ctrlq_pending) before exiting the
cleanup routine.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean control queues only when they are initialized. One of the ways to
validate if the basic initialization is done is by checking value of
cq->sq.head and cq->rq.head variables that specify the register address.
This patch adds a check to avoid NULL pointer dereference crash when tried
to shutdown uninitialized control queue.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is not safe to have the string table for statistics change order or
size over the lifetime of a given netdevice. This is because of the
nature of the 3-step process for obtaining stats. First, user space
performs a request for the size of the strings table. Second it performs
a separate request for the strings themselves, after allocating space
for the table. Third, it requests the stats themselves, also allocating
space for the table.
If the size decreased, there is potential to see garbage data or stats
values. In the worst case, we could potentially see stats values become
mis-aligned with their strings, so that it looks like a statistic is
being reported differently than it actually is.
Even worse, if the size increased, there is potential that the strings
table or stats table was not allocated large enough and the stats code
could access and write to memory it should not, potentially resulting in
undefined behavior and system crashes.
It isn't even safe if the size always changes under the RTNL lock. This
is because the calls take place over multiple user space commands, so it
is not possible to hold the RTNL lock for the entire duration of
obtaining strings and stats. Further, not all consumers of the ethtool
API are the user space ethtool program, and it is possible that one
assumes the strings will not change (valid under the current contract),
and thus only requests the stats values when requesting stats in a loop.
Finally, it's not possible in the general case to detect when the size
changes, because it is quite possible that one value which could impact
the stat size increased, while another decreased. This would result in
the same total number of stats, but reordering them so that stats no
longer line up with the strings they belong to. Since only size changes
aren't enough, we would need some sort of hash or token to determine
when the strings no longer match. This would require extending the
ethtool stats commands, but there is no more space in the relevant
structures.
The real solution to resolve this would be to add a completely new API
for stats, probably over netlink.
In the ice driver, the only thing impacting the stats that is not
constant is the number of queues. Instead of reporting stats for each
used queue, report stats for each allocated queue. We do not change the
number of queues allocated for a given netdevice, as we pass this into
the alloc_etherdev_mq() function to set the num_tx_queues and
num_rx_queues.
This resolves the potential bugs at the slight cost of displaying many
queue statistics which will not be activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use define for the unit size shift of the Rx LAN context descriptor base
address instead of the magic number 7.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is already a check for owner == ICE_SCHED_NODE_OWNER_LAN at the
beginning of ice_sched_update_vsi_child_nodes. Remove the additional
check to address the static analysis tool smatch issue "warn: we tested
'owner' before and it was 'false'".
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the following smatch errors:
1) Fix "odd binop '0x0 & 0xc'" when performing the bitwise-and with a
constant value of zero (ICE_AQC_GSET_RSS_LUT_TABLE_SIZE_128_FLAG).
Remove a similar bitwise-and with 0 in ice_add_marker_act() and use the
right mask ICE_LG_ACT_GENERIC_OFFSET_M in the expression.
2) Fix a similar issue "odd binop '0x0 & 0x1800' in ice_req_irq_msix_misc.
3) Fix "odd binop '0x380000 & 0x7fff8'" in ice_add_marker_act(). Also, use
a new define ICE_LG_ACT_GENERIC_OFF_RX_DESC_PROF_IDX instead of magic
number '7'.
4) Fix warn: odd binop '0x0 & 0x18' in ice_set_dflt_vsi_ctx() by removing
unnecessary logic to explicitly unset bits 3 and 4 in port_vlan_bits.
These bits are unset already by the memset on ctxt->info.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'truesize' is supposed to be u32, not int, so fix it.
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of
PAGE_SIZE is 65536(64K). But the type of page_offset is u16, it will
overflow. So change it to u32, when "CONFIG_ARM64_64K_PAGES" enabled.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update hns to drop the hns_nic_get_headlen function in favour of
eth_get_headlen, and hence also removes now redundant hns_nic_get_headlen.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is not meant to be tracking amount of used bytes in a skb,
but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment, we have to
account the full size of the fragment.
So skb_add_rx_frag needs to calculate the length of the entire buffer into
turesize.
Fixes: 9cbe9fd521 ("net: hns: optimize XGE capability by reducing cpu usage")
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'truesize' is supposed to be u32, not int, so fix it.
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the type of length and page_offset are u16, they will
overflow. So change them to u32.
Fixes: 6fe6611ff2 ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core signal handling updates from Eric Biederman:
"It was observed that a periodic timer in combination with a
sufficiently expensive fork could prevent fork from every completing.
This contains the changes to remove the need for that restart.
This set of changes is split into several parts:
- The first part makes PIDTYPE_TGID a proper pid type instead
something only for very special cases. The part starts using
PIDTYPE_TGID enough so that in __send_signal where signals are
actually delivered we know if the signal is being sent to a a group
of processes or just a single process.
- With that prep work out of the way the logic in fork is modified so
that fork logically makes signals received while it is running
appear to be received after the fork completes"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (22 commits)
signal: Don't send signals to tasks that don't exist
signal: Don't restart fork when signals come in.
fork: Have new threads join on-going signal group stops
fork: Skip setting TIF_SIGPENDING in ptrace_init_task
signal: Add calculate_sigpending()
fork: Unconditionally exit if a fatal signal is pending
fork: Move and describe why the code examines PIDNS_ADDING
signal: Push pid type down into complete_signal.
signal: Push pid type down into __send_signal
signal: Push pid type down into send_signal
signal: Pass pid type into do_send_sig_info
signal: Pass pid type into send_sigio_to_task & send_sigurg_to_task
signal: Pass pid type into group_send_sig_info
signal: Pass pid and pid type into send_sigqueue
posix-timers: Noralize good_sigevent
signal: Use PIDTYPE_TGID to clearly store where file signals will be sent
pid: Implement PIDTYPE_TGID
pids: Move the pgrp and session pid pointers from task_struct to signal_struct
kvm: Don't open code task_pid in kvm_vcpu_ioctl
pids: Compute task_tgid using signal->leader_pid
...
After commit 90b73b77d0, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.
Fixes: 90b73b77d0 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registering another device with same MAC address (such as TAP, VPN or
DPDK KNI) will confuse the VF autobinding logic. Restrict the search
to only run if the device is known to be a PCI attached VF.
Fixes: e8ff40d4bf ("hv_netvsc: improve VF device matching")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a new Dell TB16 dock with a different iSerialNumber.
Apply the same fix from commit 0b1655143d ("r8152: disable RX
aggregation on Dell TB16 dock") to this model.
BugLink: https://bugs.launchpad.net/bugs/1785780
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep sending mailbox commands to the MFW when it is not responsive ends up
with a redundant amount of timeout expiries.
This patch prints the MCP status on the first command which is not
responded, and blocks the following commands.
Since the (un)load request commands might be not responded due to other
PFs, the patch also adds the option to skip the blocking upon a failure.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW manages an internal lock to prevent concurrent hardware
(de)initialization of different PFs.
This, together with the busy-waiting for the MFW's responses for commands,
might lead to a deadlock during concurrent load or unload of PFs.
This patch adds the option to sleep within the busy-waiting, and uses it
for the (un)load requests (which are not sent from an interrupt context) to
prevent the possible deadlock.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix races in IPVS, from Tan Hu.
2) Missing unbind in matchall classifier, from Hangbin Liu.
3) Missing act_ife action release, from Vlad Buslov.
4) Cure lockdep splats in ila, from Cong Wang.
5) veth queue leak on link delete, from Toshiaki Makita.
6) Disable isdn's IIOCDBGVAR ioctl, it exposes kernel addresses. From
Kees Cook.
7) RCU usage fixup in XDP, from Tariq Toukan.
8) Two TCP ULP fixes from Daniel Borkmann.
9) r8169 needs REALTEK_PHY as a Kconfig dependency, from Heiner
Kallweit.
10) Always take tcf_lock with BH disabled, otherwise we can deadlock
with rate estimator code paths. From Vlad Buslov.
11) Don't use MSI-X on RTL8106e r8169 chips, they don't resume properly.
From Jian-Hong Pan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ip6_vti: fix creating fallback tunnel device for vti6
ip_vti: fix a null pointer deferrence when create vti fallback tunnel
r8169: don't use MSI-X on RTL8106e
net: lan743x_ptp: convert to ktime_get_clocktai_ts64
net: sched: always disable bh when taking tcf_lock
ip6_vti: simplify stats handling in vti6_xmit
bpf: fix redirect to map under tail calls
r8169: add missing Kconfig dependency
tools/bpf: fix bpf selftest test_cgroup_storage failure
bpf, sockmap: fix sock_map_ctx_update_elem race with exist/noexist
bpf, sockmap: fix map elem deletion race with smap_stop_sock
bpf, sockmap: fix leakage of smap_psock_map_entry
tcp, ulp: fix leftover icsk_ulp_ops preventing sock from reattach
tcp, ulp: add alias for all ulp modules
bpf: fix a rcu usage warning in bpf_prog_array_copy_core()
samples/bpf: all XDP samples should unload xdp/bpf prog on SIGTERM
net/xdp: Fix suspicious RCU usage warning
net/mlx5e: Delete unneeded function argument
Documentation: networking: ti-cpsw: correct cbs parameters for Eth1 100Mb
isdn: Disable IIOCDBGVAR
...
Found the ethernet network on ASUS X441UAR doesn't come back on resume
from suspend when using MSI-X. The chip is RTL8106e - version 39.
[ 21.848357] libphy: r8169: probed
[ 21.848473] r8169 0000:02:00.0 eth0: RTL8106e, 0c:9d:92:32:67:b4, XID
44900000, IRQ 127
[ 22.518860] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 29.458041] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
[ 63.227398] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full -
flow control off
[ 124.514648] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
Here is the ethernet controller in detail:
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
Falling back to MSI fixes the issue.
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timekeeping_clocktai64() has been renamed to ktime_get_clocktai_ts64()
for consistency with the other ktime_get_* access functions.
Rename the new caller that has come up as well.
Question: this is the only ptp driver that sets the hardware time
to the current system time in TAI. Why does it do that?
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Now that we switched the r8169 driver to use phylib, there's a
dependency on the Realtek PHY drivers. This dependency was missing
in Kconfig.
Reported-by: Jouni Mettälä <jtmettala@gmail.com>
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rdma.git merge resolution for the 4.19 merge window
Conflicts:
drivers/infiniband/core/rdma_core.c
- Use the rdma code and revise with the new spelling for
atomic_fetch_add_unless
drivers/nvme/host/rdma.c
- Replace max_sge with max_send_sge in new blk code
drivers/nvme/target/rdma.c
- Use the blk code and revise to use NULL for ib_post_recv when
appropriate
- Replace max_sge with max_recv_sge in new blk code
net/rds/ib_send.c
- Use the net code and revise to use NULL for ib_post_recv when
appropriate
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
priv argument is not used by the function, delete it.
Fixes: a89842811e ("net/mlx5e: Merge per priority stats groups")
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz9477 is superset of ksz9xx series, driver just works
out of the box for ksz9897 chip with this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltwm2geHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGITkH/iSzkVhT2OxHoir0
mLVzTi7/Z17L0e/ELl7TvAC0iLFlWZKdlGR0g3b4/QpXLPmNK4HxiDRTQuWn8ke0
qDZyDq89HqLt+mpeFZ43PCd9oqV8CH2xxK3iCWReqv6bNnowGnRpSStlks4rDqWn
zURC/5sUh7TzEG4s997RrrpnyPeQWUlf/Mhtzg2/WvK2btoLWgu5qzjX1uFh3s7u
vaF2NXVJ3X03gPktyxZzwtO1SwLFS1jhwUXWBZ5AnoJ99ywkghQnkqS/2YpekNTm
wFk80/78sU+d91aAqO8kkhHj8VRrd+9SGnZ4mB2aZHwjZjGcics4RRtxukSfOQ+6
L47IdXo=
=sJkt
-----END PGP SIGNATURE-----
Merge tag 'v4.18' into rdma.git for-next
Resolve merge conflicts from the -rc cycle against the rdma.git tree:
Conflicts:
drivers/infiniband/core/uverbs_cmd.c
- New ifs added to ib_uverbs_ex_create_flow in -rc and for-next
- Merge removal of file->ucontext in for-next with new code in -rc
drivers/infiniband/core/uverbs_main.c
- for-next removed code from ib_uverbs_write() that was modified
in for-rc
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
-----BEGIN PGP SIGNATURE-----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=2Dmn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is supplied
(Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum (Jakub
Kicinski)
* pci/misc:
PCI: Limit config space size for Netronome NFP5000
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Unify PCI and normal DMA direction definitions
PCI: Use IRQF_ONESHOT if pci_request_irq() called with no handler
PCI: Call dma_debug_add_bus() for pci_bus_type from PCI core
PCI: Mark fall-through switch cases before enabling -Wimplicit-fallthrough
# Conflicts:
# drivers/pci/hotplug/pciehp_ctrl.c
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
* pci/aspm:
PCI: Remove unnecessary include of <linux/pci-aspm.h>
iwlwifi: Remove unnecessary include of <linux/pci-aspm.h>
ath9k: Remove unnecessary include of <linux/pci-aspm.h>
igb: Remove unnecessary include of <linux/pci-aspm.h>
PCI/ASPM: Convert to use sysfs_match_string() helper
Syzbot continues to try to create mac80211_hwsim radios, and
manages to pass parameters that are later checked with WARN_ON
in cfg80211 - catch another one in hwsim directly.
Reported-by: syzbot+2a12f11c306afe871c1f@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a lot of examples in the kernel where PCI_VDEVICE() is used and
still looks not so convenient due to additional driver_data field attached.
Introduce PCI_DEVICE_DATA() macro to fully describe device ID entry in
shortest possible form. For example,
before:
{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_MRFLD),
(kernel_ulong_t) &dwc3_pci_mrfld_properties, },
after:
{ PCI_DEVICE_DATA(INTEL, MRFLD, &dwc3_pci_mrfld_properties) },
Drivers can be converted later on in independent way.
While here, remove the unused macro with the same name from Ralink wireless
driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # for rt2x00
- Revert two ACPICA commits that are not needed any more (Erik
Schmauss).
- Rework property graph support in the ACPI device properties
framework to make it behave more like the analogous DT code
and update the documentation of it (Sakari Ailus).
- Change the default ACPI device status after initialization
to ACPI_STA_DEFAULT instead of 0 (Hans de Goede).
- Add a special platform driver for enumerating multiple I2C devices
hooked up to the same object in the ACPI tables (Hans de Goede).
- Fix the ACPI battery driver to avoid reporting full capacity on
systems without support for that and clean it up (Hans de Goede,
Dmitry Rozhkov, Lucas Rangit Magasweran).
- Add two system wakeup quirks to the ACPI EC driver (Aaron Ma,
Mika Westerberg).
- Add the touchscreen on Dell Venue Pro 7139 to the list of "always
present" devices to make it work (Tristian Celestin).
- Revert a special tables handling quirk for Dell XPS 9570 and
Precision M5530 which is not needed any more (Kai Heng Feng).
- Add support for a new OEM _OSI string to allow system vendors to
work around issues with NVidia HDMI audio (Alex Hung).
- Prevent the ACPI button driver from reporting excessive system
wakeup events and clean it up (Ravi Chandra Sadineni, Randy Dunlap).
- Clean up two minor code style issues in the ACPI core and GHES
handling on ARM64 (Dongjiu Geng, John Garry, Tom Todd).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5mW8
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These revert two ACPICA commits that are not needed any more, rework
the property graphs support in ACPI to be more aligned with the
analogous DT code, add some new quirks and remove one that isn't
needed any more, add a special platform driver to enumerate multiple
I2C devices hooked up to the same device object in the ACPI tables and
update the battery and button drivers.
Specifics:
- Revert two ACPICA commits that are not needed any more (Erik
Schmauss).
- Rework property graph support in the ACPI device properties
framework to make it behave more like the analogous DT code and
update the documentation of it (Sakari Ailus).
- Change the default ACPI device status after initialization to
ACPI_STA_DEFAULT instead of 0 (Hans de Goede).
- Add a special platform driver for enumerating multiple I2C devices
hooked up to the same object in the ACPI tables (Hans de Goede).
- Fix the ACPI battery driver to avoid reporting full capacity on
systems without support for that and clean it up (Hans de Goede,
Dmitry Rozhkov, Lucas Rangit Magasweran).
- Add two system wakeup quirks to the ACPI EC driver (Aaron Ma, Mika
Westerberg).
- Add the touchscreen on Dell Venue Pro 7139 to the list of "always
present" devices to make it work (Tristian Celestin).
- Revert a special tables handling quirk for Dell XPS 9570 and
Precision M5530 which is not needed any more (Kai Heng Feng).
- Add support for a new OEM _OSI string to allow system vendors to
work around issues with NVidia HDMI audio (Alex Hung).
- Prevent the ACPI button driver from reporting excessive system
wakeup events and clean it up (Ravi Chandra Sadineni, Randy
Dunlap).
- Clean up two minor code style issues in the ACPI core and GHES
handling on ARM64 (Dongjiu Geng, John Garry, Tom Todd)"
* tag 'acpi-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
platform/x86: Add ACPI i2c-multi-instantiate pseudo driver
ACPI / x86: utils: Remove status workaround from acpi_device_always_present()
ACPI / scan: Create platform device for fwnodes with multiple i2c devices
ACPI / scan: Initialize status to ACPI_STA_DEFAULT
ACPI / EC: Add another entry for Thinkpad X1 Carbon 6th
ACPI: bus: Fix a pointer coding style issue
arm64 / ACPI: clean the additional checks before calling ghes_notify_sea()
ACPI / scan: Add static attribute to indirect_io_hosts[]
ACPI / battery: Do not export energy_full[_design] on devices without full_charge_capacity
ACPI / EC: Use ec_no_wakeup on ThinkPad X1 Yoga 3rd
ACPI / battery: get rid of negations in conditions
ACPI / battery: use specialized print macros
ACPI / battery: reorder headers alphabetically
ACPI / battery: drop inclusion of init.h
ACPI: battery: remove redundant old_present check on insertion
ACPI: property: graph: Update graph documentation to use generic references
ACPI: property: graph: Improve graph documentation for port/ep numbering
ACPI: property: graph: Fix graph documentation
ACPI: property: Update documentation for hierarchical data extension 1.1
ACPI: property: Document key numbering for hierarchical data extension refs
...
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW3HajRscamFjZWsuYW5h
c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdvxAwEA+qS5O9ByxlhT+BUC4ck6
nIy0ITOCXP8ySoo8VVhzjikBAPrb9lFYGvHqzKN4dYtnSILPmlTSf1t1flng2Zev
NfoE
=lNwq
-----END PGP SIGNATURE-----
Merge tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED triggers improvements make the biggest part of this pull request.
The most striking ones, that allowed for nice cleanups in the triggers
are:
- centralized handling of creation and removal of trigger sysfs
attributes via attribute group
- addition of module_led_trigger() helper
The other things that need to be mentioned:
New features and improvements to existing LED class drivers:
- lt3593: add DT support, switch to gpiod interface
- lm3692x: support LED sync configuration, change OF calls to fwnode
calls
- apu: modify PC Engines apu/apu2 driver to support apu3
Change in the drivers/net/can/led.c:
- mark led trigger as broken since it's in the way for the further
cleanups. It implements a subset of the netdev trigger and an Ack
is needed from someone who can actually test and confirm that the
netdev trigger works for can devices"
* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
leds: ns2: Change unsigned to unsigned int
usb: simplify usbport trigger
leds: gpio trigger: simplifications from core changes
leds: backlight trigger: simplifications from core changes
leds: activity trigger: simplifications from core changes
leds: default-on trigger: make use of module_led_trigger()
leds: heartbeat trigger: simplifications from core changes
leds: oneshot trigger: simplifications from core changes
leds: transient trigger: simplifications from core changes
leds: timer trigger: simplifications from core changes
leds: netdev trigger: simplifications from core changes
leds: triggers: new function led_set_trigger_data()
leds: triggers: define module_led_trigger helper
leds: triggers: handle .trigger_data and .activated() in the core
leds: triggers: add device attribute support
leds: triggers: let struct led_trigger::activate() return an error code
leds: triggers: make the MODULE_LICENSE string match the actual license
leds: lm3692x: Support LED sync configuration
dt: bindings: lm3692x: Update binding for LED sync control
leds: lm3692x: Change DT calls to fwnode calls
...
The recent commit 916c5e1413 ("hv/netvsc: fix handling of fallback
to single queue mode") tried to fix the fallback behavior to a single
queue mode, but it changed the function to return zero incorrectly,
while the function should return an object pointer. Eventually this
leads to a NULL dereference at the callers that expect non-NULL
value.
Fix it by returning the proper net_device object.
Fixes: 916c5e1413 ("hv/netvsc: fix handling of fallback to single queue mode")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added a new error path, but we need to drop the lock before we return.
Fixes: 2d2e1dd299 ("net: dsa: mv88e6xxx: Cache the port cmode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to test if these flags are set but there are some && vs &
typos.
Fixes: efd1ba6af9 ("net: dsa: mv88e6xxx: Add SERDES phydev_mac_change up for 6390")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the error path to unsubscribe all other phy's from
current phy. The actually code using a wrong kind of list iteration may
copied from the case to unsubscribe the current phy from all other
phy's.
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revision(0x20) HW does not support enabling or disabling individual
netdev's HW_VLAN_CTAG_FILTER feature, and Revision(0x21) supports
enabling or disabling individual netdev's HW_VLAN_CTAG_FILTER
feature.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS3_RING_TX_RING_TC_REG register is used to map tx ring to
specific tc, the tx queue to tc mapping is needed by the hardware
to do the correct tx schedule.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no HNS3_RING_TX_RING_BD_LEN_REG register according
to UM, so this patch removes it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user set the channel num using "ethtool -L ethX", the desc num
of BD will set to default value, which will cause desc num set by
user lost problem.
This patch fixes it by restoring the desc num set by user when setting
channel num.
Fixes: 09f2af6405 ("net: hns3: add support to modify tqps number")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For marvell phy m88e1510, bit SUPPORTED_FIBRE of phydev->supported
is default on. Both phy_resume() and phy_suspend() will check the
SUPPORTED_FIBRE bit and write register of fibre page.
Currently in hns3 driver, the SUPPORTED_FIBRE bit will be cleared
after phy_connect_direct() finished. Because phy_resume() is called
in phy_connect_direct(), and phy_suspend() is called when disconnect
phy device, so the operation for fibre page register is not symmetrical.
It will cause phy link issue when reload hns3 driver.
This patch fixes it by disable the SUPPORTED_FIBRE before connecting
phy.
Fixes: 256727da73 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function call of phy_connect_direct will reinitialize phydev. Some
information like advertising will be lost. Phy_connect_direct only
needs to be called once. And driver can run well. This patch adds
some functions to ensure that phy_connect_direct is called only once
to solve the information of phydev lost problem occurring when we stop
the net and open it again.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the functional specification of hardware, the first
descriptor of response from command 'lookup vlan talbe' is not valid.
Currently, the first descriptor is parsed as normal value, which will
cause an expected error.
This patch fixes this problem by skipping the first descriptor.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for serdes loopback selftest in hns3
driver.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge ACPICA changes and updates of the ACPI device properties
framework for 4.19.
These revert two ACPICA commits that are not needed any more and
modify the properties graph support in ACPI to be more in-line with
the analogous DT code.
* acpica:
ACPICA: Update version to 20180629
ACPICA: Revert "iASL compiler: allow compilation of externals with paths that refer to existing names"
ACPICA: Revert "iASL: change processing of external op namespace nodes for correctness"
* acpi-property:
ACPI: property: graph: Update graph documentation to use generic references
ACPI: property: graph: Improve graph documentation for port/ep numbering
ACPI: property: graph: Fix graph documentation
ACPI: property: Update documentation for hierarchical data extension 1.1
ACPI: property: Document key numbering for hierarchical data extension refs
ACPI: property: Use data node name and reg property for graphs
ACPI: property: Allow direct graph endpoint references
ACPI: property: Make the ACPI graph API private
ACPI: property: Document hierarchical data extension references
ACPI: property: Allow making references to non-device nodes
ACPI: Convert ACPI reference args to generic fwnode reference args
The bnxt_coredump_record structure is very long, causing a warning
about possible stack overflow on 32-bit architectures:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c: In function 'bnxt_get_coredump':
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2989:1: error: the frame size of 1188 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
I could not see any reason to operate on an on-stack copy of the
structure before copying it back into the caller-provided buffer, which
also simplifies the code here.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining caller of this function is inside of an #ifdef
after another caller got removed. This causes a harmless warning
in some configurations:
drivers/net/ethernet/broadcom/bcmsysport.c:1068:13: error: 'bcm_sysport_resume_from_wol' defined but not used [-Werror=unused-function]
Removing the #ifdef around the PM functions simplifies the code
and avoids the problem but letting the compiler drop the unused
functions silently.
Fixes: 9e85e22713 ("net: systemport: Do not re-configure upon WoL interrupt")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added suspend/resume functions cause a build warning
when CONFIG_PM is disabled:
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c:324:12: error: 'stmmac_pci_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c:306:12: error: 'stmmac_pci_suspend' defined but not used [-Werror=unused-function]
Mark them as __maybe_unused so gcc can drop them silently.
Fixes: b7d0f08e91 ("net: stmmac: Fix WoL for PCI-based setups")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The utsname()->nodename string may be 64 bytes long, and it gets
copied without the trailing nul byte into the shorter record->system_name,
as gcc now warns:
In file included from include/linux/bitmap.h:9,
from include/linux/ethtool.h:16,
from drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:13:
In function 'strncpy',
inlined from 'bnxt_fill_coredump_record' at drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2863:2:
include/linux/string.h:254:9: error: '__builtin_strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Using strlcpy() at least avoids overflowing the destination buffer
and adds proper nul-termination. It may still truncate long names
though, which probably can't be solved here.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building without CONFIG_PTP_1588_CLOCK results in multiple failures,
this was obviously not well tested:
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_isr':
drivers/net/ethernet/microchip/lan743x_ptp.c:781:28: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
ptp_schedule_worker(ptp->ptp_clock, 0);
^~~~~~~~~
tx_ts_lock
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_open':
drivers/net/ethernet/microchip/lan743x_ptp.c:879:6: error: unused variable 'ret' [-Werror=unused-variable]
int ret = -ENODEV;
^~~
At top level:
drivers/net/ethernet/microchip/lan743x_ptp.c:63:13: error: 'lan743x_ptp_tx_ts_enqueue_ts' defined but not used [-Werror=unused-function]
static void lan743x_ptp_tx_ts_enqueue_ts(struct lan743x_adapter *adapter,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
drivers/net/ethernet/microchip/lan743x_ethtool.c: In function 'lan743x_ethtool_get_ts_info':
drivers/net/ethernet/microchip/lan743x_ethtool.c:558:19: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
Those #ifdef checks are hard to get right, replace them all with
IS_ENABLED() checks that leave the same code visible to the compiler
but let it optimize out the unused bits based on the configuration.
Fixes: 07624df1c9 ("lan743x: lan743x: Add PTP support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan743x now fails to build when CONFIG_CRC16 is disabled:
drivers/net/ethernet/microchip/lan743x_main.o: In function crc16'
Force it on like all other users do.
Fixes: 4d94282afd ("lan743x: Add power management support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove 'Return:' information from functions which no longer
return a value. Also update name and return types of nfp_nffw_info
access functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last argument to mlx5_add_flow_rules passes the number of
destinations in the struct pointed to by the dest arg. Change the name
to better reflect this fact.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
lib/clock.c includes clock related functions which require ptp support.
Thus compile out lib/clock.c and add the needed function stubs in case
kconfig CONFIG_PTP_1588_CLOCK is off.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When vxlan is not enabled by kernel, no need to enable it in mlx5.
Compile out lib/vxlan.c if CONFIG_VXLAN is not selected.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
