If both link partners are Aquantia PHY's then additional information is
exchanged as part of the auto-negotiation. Report remote capabilities
if link partner is Aquantia PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the green and amber LEDs on this quad PHY were solid, to
indicate an encoding of the link speed (10/100/1000).
This keeps the LEDs always on just as before, but now they flash on
Rx/Tx activity.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we effectively clear the BMCR register. Some PHY's can deal
with this (e.g. because they reset BMCR to a default as part of a
soft-reset) whilst on others this causes issues because e.g. the
autoneg bit is cleared. Marvell is an example, see also thread [0].
So let's be a little bit more gentle and leave all bits we're not
interested in as-is. This change is needed for PHY drivers to
properly deal with the original patch.
[0] https://marc.info/?t=155264050700001&r=1&w=2
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Tested-by: Phil Reid <preid@electromag.com.au>
Tested-by: liweihang <liweihang@hisilicon.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 90eff9096c ("net: phy: Allow splitting MDIO bus/device support
from PHYs") the various MDIO bus drivers were no longer parented with
config PHYLIB but with config MDIO_BUS which is not a menuconfig, fix
this by depending on MDIO_DEVICE which is a menuconfig.
This is visually nicer and less confusing for users.
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tristate prompt should have been replaced rather than defined a few
lines below, rebase mistake.
Fixes: 17cc982176 ("net: phy: Move Omega PHY entry to Cygnus PHY driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia PHY's of the AQR107 family support the downshift feature.
Add support for it as standard PHY tunable so that it can be controlled
via ethtool.
The AQCS109 supports a proprietary 2-pair 1Gbps mode. If two such PHY's
are connected to each other with a 2-pair cable, they may not be able
to establish a link if both advertise modes > 1Gbps.
v2:
- add downshift event detection
- warn if downshift occurred
- read downshifted rate from vendor register
- enable downshift per default on all AQR107 family members
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cygnus and Omega are part of the same business unit and product line, it
makes sense to group PHY entries by products such that a platform can
select only the drivers that it needs. Bring all the functionality that
the BCM7XXX_28NM_GPHY() macro hides for us and remove the Omega PHY
entry from bcm7xxx.c.
As an added bonus, we now have a proper mdio_device_id entry to permit
auto-loading.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Omega PHY entry was added to bcm7xxx.c out of convenience and this
breaks the one driver per product line paradigm that was applied up
until now. Since the AFE initialization is shared between Omega and
BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional
changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, especially given we use a dev_info() which
already displays the platform device's address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the auto-negotiated speed the PHY may change the interface
mode. Check for new mode and set phydev->interface accordingly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: picked from bigger patch and reworked]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let config_init check for unsupported interface modes on AQR107/AQCS109.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: adjusted for AQR107/AQCS109 specifics]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the Phy driver's link_change_notify callback is called
whenever the state machine is run (every second if polling), no matter
whether the state changed or not. This isn't needed and may confuse
users considering the name of the callback. Actually it contradicts
its kernel-doc description. Therefore let's change the behavior and
call this callback only in case of an actual state change.
This requires changes to the at803x and rockchip drivers.
at803x can be simplified so that it reacts on a state change to
PHY_NOLINK only.
The rockchip driver can also be much simplified. We simply re-init
the AFE/DSP registers whenever we change to PHY_RUNNING and speed
is 100Mbps. This causes very small overhead because we do this even
if the speed was 100Mbps already. But this is negligible and
I think justified by the much simpler code.
Changes are compile-tested only.
A little bit problematic seems to be to find somebody with the
hardware to test the changes to the two PHY drivers. See also [0].
David may be able to test the Rockchip driver.
[0] https://marc.info/?t=153782508800006&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an interrupt is already pending when the interrupt is enabled on the
GXL phy, no IRQ will ever be triggered.
The fix is simply to make sure pending IRQs are cleared before setting
up the irq mask.
Fixes: cf127ff20a ("net: phy: meson-gxl: add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_BUS_MUX can only be selected if OF_MDIO is already turned on:
WARNING: unmet direct dependencies detected for MDIO_BUS_MUX
Depends on [n]: NETDEVICES [=y] && MDIO_BUS [=m] && OF_MDIO [=n]
Selected by [m]:
- MDIO_BUS_MUX_MULTIPLEXER [=m] && NETDEVICES [=y] && MDIO_BUS [=m] && OF [=y]
Fixes: 7865ad6551 ("drivers: net: phy: mdio-mux: Add support for Generic Mux controls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As can be seen from the usage of the return value, we should use
phy_modify_mmd_changed() here.
Fixes: 9a5dc8af44 ("net: phy: add genphy_c45_an_config_aneg")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_no_soft_reset and gen10g_no_soft_reset are both the same no-ops,
one is enough.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen10g_read_status is deprecated, therefore stop exporting it.
We don't want to encourage anybody to use it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_LINK_MODE_10000baseT_Full_BIT is set anyway in the supported
and advertising bitmap because it's part of PHY_10GBIT_FEATURES.
And all users of gen10g_config_init use PHY_10GBIT_FEATURES.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend() and phy_resume() are no-ops anyway if no callback is
defined. Therefore we don't need these stubs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have it let's use genphy_c45_aneg_done() in phy_aneg_done().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging an issue I found implausible values in state->pause.
Reason in that state->pause isn't initialized and later only single
bits are changed. Also the struct itself isn't initialized in
phylink_resolve(). So better initialize state->pause and other
not yet initialized fields.
v2:
- use right function name in subject
v3:
- initialize additional fields
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to the 3310, the 2110 PHY correctly reports it's 2.5G/5G
abilities. We can therefore use the genphy_c45_pma_read_abilities helper
to build the list of features.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The genphy_c45_pma_read_abilities helper now sets the Autoneg ability
in phydev->supported according to what the AN MMD reports.
We therefore don't need to manually do that in mv3310_get_features().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to dp83640 delay after soft reset
is needed to set up registers correctly.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Generic Mux controls, when Mdio mux node is a consumer
of mux produced by some other device.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds HWMON support for the temperature sensor and the related
alarms on the 107/108/109 chips. This patch is based on work from
Nikita and Andrew. I added:
- support for changing alarm thresholds via sysfs
- move HWMON code to a separate source file to improve maintainability
- smaller changes like using IS_REACHABLE instead of ifdef
(avoids problems if PHY driver is built in and HWMON is a module)
v2:
- remove struct aqr_priv
- rename header file to aquantia.h
v3:
- add conditional compiling of aquantia_hwmon.c
- improve converting sensor register values to/from long
- add helper aqr_hwmon_test_bit
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename aquantia.c to aquantia_main.c to be prepared for adding new
functionality to separate source code files.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the switch to phy_resolve_aneg_linkmode() we don't read from the
chip any longer what is advertised but use phydev->advertising directly.
For a fixed phy however this bitmap is empty so far, what results in
no common mode being found. This breaks DSA. Fix this by advertising
everything that is supported. For a normal phy this done by phy_probe().
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto-neg emulation currently doesn't set bit BMCR_ANENABLE in BMCR,
add this. Users will ignore speed and duplex settings in BMCR because
we're emulating auto-neg, therefore we can remove related code.
See also following discussion [0].
[0] https://marc.info/?t=155041784900002&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 88x2110 PHY, which is similar to the
already supported 88x3310 PHY without the SFP interface.
It supports 10/100/1000BASET along with 2.5GBASET, 5GBASET and 10GBASET,
with the same interface modes that are used by the 3310.
This PHY don't have the same issue as the 88x3310 regarding 2.5/5G
abilities, and correctly follows the 802.3bz standard to list the
supported abilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3bz, if bit 14 of (1.11) "PMA Extended Abilities" indicates
whether or not we should read register (1.21) "2.52/5G PMA Extended
Abilities", which contains information on the support of 2.5GBASET and
5GBASET.
After testing on several variants of PHYS of this family, it appears
that bit 14 in (1.11) isn't always set when it should be.
PHYs 88X3310 (on MacchiatoBin) and 88E2010 do support 2.5G and 5GBASET,
but don't have 1.11.14 set. Their register 1.21 is filled with the
correct values, indicating 2.5G and 5G support.
PHYs 88E2110 do have their 1.11.14 bit set, as it should.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY ID corresponding to the 88X3310 is also used for other PHYs in
the same family, such as the 88E2010. Use a #define for the PHY id, that
ignores the last nibble.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.
Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.
At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.
This was tested with :
- The 88X3310, which is on the MacchiatoBin
- The 88E2010, an Alaska PHY that has no fiber interfaces, and is
limited to 5G maximum speed.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch making use of helpers dedicated to linkmodes handling.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Alaska family of 10G PHYs has more abilities than the ones listed in
PHY_10GBIT_FULL_FEATURES, the exact list depending on the model.
Make use of the newly introduced .get_features call to build this list,
using genphy_c45_pma_read_abilities to build the list of supported
linkmodes, and adding autoneg ability based on what's reported by the AN
MMD.
.config_init is still used to validate the interface_mode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code reports a link as up if all devices (except a few
blacklisted ones) report the link as up. This breaks Aquantia AQCS109
for lower speeds because on this PHY the PCS link status reflects a
10G link only. For Marvell there's a similar issue, therefore PHYXS
device isn't checked.
There may be more PHYs where depending on the mode the link status
of only selected devices is relevant.
For now it seems to be sufficient to check the link status of the
PMAPMD device only. Leave the loop in the code to be prepared in
case we have to add functionality to check more than one device,
depending on the mode.
Successfully tested on a board with an AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using genphy_c45_read_abilities() as get_features callback we
also have to set the autoneg capability in phydev->supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by
commit 0d2e778e38
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_read_status(). 1000BaseT link partner
advertisement needs to be read from vendor registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because 1000BaseT isn't covered by Clause 45, the 1000BaseT flags in
phydev->lp_advertising may have been set based on vendor registers
already. genphy_c45_read_lpa() would clear these flags as of today.
Therefore switch to mii_lpa_mod_linkmode_lpa_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the generic c45 code, plus code specific to the Aquantia
phy for 1000BaseT negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AQCS109 belongs to a family of PHY's where certain members don't
support 5G or 10G. However for all members of the family the chip
reports 10G and 5G capability. Therefore remove the not supported
modes for AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.
So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.
Fixes: cd28d1d6e5: ("net: phy: at803x: Disable phy delay for RGMII mode")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new PHY driver call to get the PHYs supported features.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: removed new config_init callback from patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genphy_c45_pma_setup_forced() makes sure the "aneg enabled"
bit is cleared, the call to genphy_c45_an_disable_aneg() isn't needed
any longer. And the code pattern is now the same as in
genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit may
still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.
v2:
- fix typo
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mii_10gbt_stat_mod_linkmode_lpa_t() in genphy_c45_read_lpa() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coccinelle warning:
./drivers/net/phy/mdio_bus.c:51:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44
./drivers/net/phy/mdio_bus.c:52:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44
fix this by using IS_ERR before PTR_ERR
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY core expects PHY drivers not to set Pause and Asym_Pause bits,
unless the driver only wants to specify one of them due to HW
limitation. In the case of the Marvell10g driver, we don't need to set
them.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have phy_resolve_aneg_linkmode() we can make
genphy_read_status() much simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have the settings array of modes which is sorted based on aneg
priority. Instead of checking each mode manually let's simply iterate
over the sorted settings.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the advertisement registers content didn't change, we may have
just switched to aneg, and therefore have to trigger an aneg restart.
This matches the behavior of genphy_config_aneg().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_config_aneg() in mv3310_config_aneg().
v2:
- add a comment regarding 1000BaseT vendor registers
v3:
- rebased
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: patch splitted]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
C45 configuration of 10/100 and multi-giga bit auto negotiation
advertisement is standardized. Configuration of 1000Base-T however
appears to be vendor specific. Move the generic code out of the
Marvell driver into the common phy-c45.c file.
v2:
- change function name to genphy_c45_an_config_aneg
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: use new helper linkmode_adv_to_mii_10gbt_adv_t and split patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.
With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell reported the following race in the phylib state machine
(quoting from his mail):
if (phy_polling_mode(phydev) && phy_is_started(phydev))
phy_queue_state_machine(phydev, PHY_STATE_TIME);
state = PHY_UP
thread 0 thread 1
phy_disconnect()
+-phy_is_started()
phy_is_started() |
`-phy_stop()
+-phydev->state = PHY_HALTED
`-phy_stop_machine()
`-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()
At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.
Fix this by protecting the complete operation in thread 0.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.3bz specification, based on previous by the NBASET alliance,
defines the 2.5GBaseT and 5GBaseT link modes for ethernet traffic on
cat5e, cat6 and cat7 cables.
These mode integrate with the already defined C45 MDIO PMA/PMD registers
set that added 10G support, by defining some previously reserved bits,
and adding a new register (2.5G/5G Extended abilities).
This commit adds the required definitions in include/uapi/linux/mdio.h
to support these modes, and detect when a link-partner advertises them.
It also adds support for these mode in the generic C45 PHY
infrastructure.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 10G PHY driver has a generic way of initializing the supported
link modes by reading the PHY's C45 PMA abilities. This can be made
generic, since these registers are part of the 802.3 specifications.
This commit extracts the config_init link_mode initialization code from
marvell10g and uses it to introduce the genphy_c45_pma_read_abilities
function.
Only PMA modes are read, it's still up to the caller to set the Pause
parameters.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since of_set_phy_supported was moved to phy-core.c, we can also move
of_set_phy_eee_broken to the same location, so that we have all OF
functions in the same place.
This patch doesn't intend to introduce any change in behaviour.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting a PHY's max speed using either the max-speed DT property
or ethtool, we should mask-out all non-compatible modes according to the
settings table, instead of just the 10/100BASET modes.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function phy_modify_mmd_changed(), the result speaks for itself.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.
This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().
Fixes: b5bfc21af5 ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide phylink_init_eee() to allow MAC drivers to initialise PHY EEE
from within the ethtool set_eee() method.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's little point calling mac_config() when the link is down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_modify_changed() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When replacing mv3310_modify() with phy_modify_mmd() we missed that
they behave differently, mv3310_modify() returns 1 on a changed
register value whilst phy_modify_mmd() returns 0. Fix this by replacing
phy_modify_mmd() with phy_modify_mmd_changed() where needed.
Fixes: b52c018ddc ("net: phy: make use of new MMD accessors")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When modifying registers there are scenarios where we need to know
whether the register content actually changed. This patch adds
new helpers to not break users of the current ones, phy_modify() etc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the AQCS109. From software point of view,
it should be almost equivalent to AQR107.
v2:
- make Nikita the author
- document what I changed
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: use PHY_ID_MATCH_MODEL mascro]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for runtime determination of what the PHY supports, by
adding a new function to the phy driver. The get_features call should
set the phydev->supported member with the features the PHY supports.
It is only called if phydrv->features is NULL.
This requires minor changes to pause. The PHY driver should not set
pause abilities, except for when it has odd cause capabilities, e.g.
pause cannot be disabled. With this change, phydev->supported already
contains the drivers abilities, including pause. So rather than
considering phydrv->features, look at the phydev->supported, and
enable pause if neither of the pause bits are already set.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: fixed small checkpatch complaint in one comment]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon support asking the PHY at runtime to determine what
features it supports, rather than forcing it to be compile time.
But we should probe the PHY first. So probe the phy driver earlier.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY registers are only 16 bits wide, therefore, if the read was
successful, there's no need to mask out the higher 16 bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 0 in register 1.5 doesn't represent a device but is a flag that
Clause 22 registers are present. Therefore disregard this bit when
populating the device list. If code needs this information it
should read register 1.5 directly instead of accessing the device
list.
Because this bit doesn't represent a device don't define a
MDIO_MMD_XYZ constant, just define a MDIO_DEVS_XYZ constant for
the flag in the device list bitmap.
v2:
- make masking of bit 0 more explicit
- improve commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status register latches link-down events. Therefore, if link
is reported as being up, there's no need for a second read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.
On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
Interrupt handler reads link status, means it reads the latched
"link is down" info. But there won't be another interrupt as long
as link stays up, therefore phylib will never recognize that link
is up.
Deal with both scenarios by reading the register twice in interrupt
mode only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we probe a SFP module, we expect to be able to call the upstream
device's module_insert() function so that the upstream link can be
configured. However, when the upstream device is delayed, we currently
may end up probing the module before the upstream device is available,
and lose the module_insert() call.
Avoid this by holding off probing the module until the SFP bus is
properly connected to both the SFP socket driver and the upstream
driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Let genphy_c45_read_link manage the devices to check, this removes
overhead from callers. Add C22EXT to the list of excluded devices
because it doesn't implement the status register. According to the
802.3 clause 45 spec registers 29.0 - 29.4 are reserved.
At the moment we have very few clause 45 PHY drivers, so we are
lacking experience whether other drivers will have to exclude further
devices, or may need to check PHY XS. If we should figure out that
list of devices to check needs to be configurable, I think best will
be to add a device list member to struct phy_driver.
v2:
- adjusted commit message
- exclude also device C22EXT from link checking
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fixed_phy_register_with_gpiod() API. It lets users create a
fixed_phy instance that uses a GPIO descriptor which was obtained
externally e.g. through platform data.
This enables platform devices (non-DT based) to use GPIOs for link
status.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix fixed_phy not checking GPIO if no link_update callback
is registered.
In the original version all users registered a link_update
callback so the issue was masked.
Fixes: a5597008db ("phy: fixed_phy: Add gpio to determine link up/down.")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make genphy_c45_read_link behave the same as genphy_update_link
and set phydev->link in the function directly. This allows to simplify
the callers. In addition don't check further devices once we detect
that at least one device reports link as down.
v2:
- remove an unused variable
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new MMD accessors.
v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full set of locked and unlocked accessor functions to read and
write PHY MMD registers and/or bitfields.
Set of functions exactly matches what is already available for PHY
legacy registers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During sendmsg() a cloned skb is saved via dp83640_txtstamp() in
->tx_queue. After the NIC sends this packet, the PHY will reply with a
timestamp for that TX packet. If the cable is pulled at the right time I
don't see that packet. It might gets flushed as part of queue shutdown
on NIC's side.
Once the link is up again then after the next sendmsg() we enqueue
another skb in dp83640_txtstamp() and have two on the list. Then the PHY
will send a reply and decode_txts() attaches it to the first skb on the
list.
No crash occurs since refcounting works but we are one packet behind.
linuxptp/ptp4l usually closes the socket and opens a new one (in such a
timeout case) so those "stale" replies never get there. However it does
not resume normal operation anymore.
Purge old skbs in decode_txts().
Fixes: cb646e2b02 ("ptp: Added a clock driver for the National Semiconductor PHYTER.")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace magic numbers with proper constants. The original patch is
from Andrew, I extended / adjusted certain parts:
- Use decimal bit numbers. The datasheet uses hex bit numbers 0 .. F.
- Order defines from highest to lowest bit numbers
- correct some typos
- add constant MDIO_AN_TX_VEND_INT_MASK2_LINK
- Remove few functional improvements from the patch, they will come as
a separate patch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of macro PHY_ID_MATCH_MODEL to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded header includes.
v2:
- leave kernel.h in
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aquantia_ as a name space prefix is rather long, resulting in lots of
lines needing wrapping, reducing readability. Use the prefix aqr_
instead, which fits with the vendor naming there devices aqr107, for
example.
v2:
- add SoB from Heiner
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY's of later RTL8168 network chips report the generic
PHYID 0x001cc800 (Realtek OUI, model and revision number both set to
zero) and therefore currently the genphy driver is used.
To be able to use the paged version of e.g. phy_write() we need a
PHY driver with the read_page and write_page callbacks implemented.
So basically make a copy of the genphy driver, just with the
read_page and write_page callbacks being set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6623c0fba1.
The original diagnosis was incorrect: it appears that the NIC had
PHY polling mode enabled, which meant that it overwrote the PHYs
advertisement register during negotiation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libphy provides a standard set of helpers to access the MMD PHY
registers. Use those instead of relying on custom driver-specific
functions.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we enable the interrupts in phy_start() we don't have to do it
before. Therefore remove enabling interrupts from phy_start_interrupts()
and rename this function to reflect the changed functionality.
v2:
- improve warning to clearly state that we fall back to polling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts don't have to be enabled before calling phy_start().
Therefore let's enable them in phy_start(). In a subsequent step
we'll remove enabling interrupts from phy_connect_direct().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_start() should be called from states PHY_READY or PHY_HALTED only.
Check for this to detect misbehaving drivers. Also the state machine
should be started only when being called from one of the valid states.
Some more background:
For all invalid states phy_start() basically was a no-op. All it did
was triggering a state machine run, but for all "running" states the
poll loop was active anyway. And if called from PHY_DOWN, the state
machine does nothing.
v3:
- extended commit message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The state machine is a no-op before phy_start() has been called.
Therefore let's enable it in phy_start() only. In phy_start()
let's call phy_start_machine() instead of phy_trigger_machine().
phy_start_machine is an alias for phy_trigger_machine but it makes
clearer that we start the state machine here instead of just
triggering a run.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the PHY and MDIO drivers refer to the COPYING file in the main
directory of this archive. This is the main license for Linux, thus
GPLv2 plus syscall extension.
Fixup the MODULE_LICENSE() where needed and add an SDPX header for
GPLv2.
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PHY drivers have the GPLv2 license text. They then either have
a MODULE_LICENSE() of GPLv2+, or an SPDX tag of GPLv2+.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup with others when there are contradictions.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PHY drivers have the GPLv2+ license text. They then either have
a MODULE_LICENSE() of GPLv2 only, or an SPDX tag of GPLv2 only.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup the others when there are contradictions.
Cc: David Wu <david.wu@rock-chips.com>
Cc: Dongpo Li <lidongpo@hisilicon.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPDX header makes any license text redundent. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RGMII mode, phy delay should be disabled. Add this case along
with disable delay routines.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the soft reset (if defined) is done only if the driver also
implements the config_init callback. I think this dependency is a
mistake, so let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that on a system with nfsboot and w/o initramfs network
fails because trying to load the PHY driver returns -ENOENT. Reason was
that due to missing initramfs the modprobe binary isn't available.
So we have to ignore error code -ENOENT.
Fixes: 13d0ab6750 ("net: phy: check return code when requesting PHY driver module")
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts have been disabled in phy_stop() already. So we can remove
phy_stop_interrupts() and free the interrupt in phy_disconnect()
directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to the phylib state machine in phy_stop() just ensures that
the state machine isn't re-triggered, but a state machine call may
be scheduled already. So lets's call phy_stop_machine().
This also allows to get rid of the call to phy_stop_machine() in
phy_disconnect().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop PHY if needed when entering phy_disconnect. This allows drivers
that don't need a separate call to phy_stop() to omit this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only caller of get_phy_id() is get_phy_device(). There a PHY ID of
0xffffffff is translated back to -ENODEV. So we can avoid some
overhead by returning -ENODEV directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since recent changes to the phylib state machine state PHY_CHANGELINK
isn't used any longer. Therefore let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver implements open-coded versions of phy_read_mmd() and
phy_write_mmd() for KSZ9031. That's not needed, let's use the
phylib functions directly.
This is compile-tested only because I have no such hardware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requesting the PHY driver module fails we'll bind the genphy
driver later. This isn't obvious to the user and may cause, depending
on the PHY, different types of issues. Therefore check the return code
of request_module(). Note that we only check for failures in loading
the module, not whether a module exists for the respective PHY ID.
v2:
- add comment explaining what is checked and what is not
- return error from phy_device_create() if loading module fails
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are already checking in phy_detach() that the PHY driver is of
generic kind (1G or 10G) and we are going to make use of that in the SFP
layer as well for 1000BaseT SFP modules, so expose helper functions to
return that information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to and one shouldn't include asm/irq.h directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago phydev_info() and friends have been added. They allow to
improve and simplify logging.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround attempt helped for some but not all affected users.
With commit 11287b693d ("r8169: load Realtek PHY driver module
before r8169") we have a better workaround now, so we an remove
the first attempt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the referenced commit, Ethernet fails to come up at boot on the
board meson-gxl-s905x-libretech-cc. Fix this by re-enabling the
genphy_soft_reset callback for the Amlogic Meson GXL PHY driver.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Timotej Lazar <timotej.lazar@araneo.si>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't
take the lock again with phy_read(), use the unlocked __phy_read().
Fixes: 424ca4c551 ("net: phy: marvell: fix paged access races")
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VOD can be out of spec, unless some magic value is poked into an
undocumented register in an undocumented page.
Fixes: e4cf8a38fc ("net: phy: Marvell: Add mv88e6390 internal PHY")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far genphy_soft_reset was used automatically if the PHY driver
didn't implement the soft_reset callback. This changed with the
mentioned commit and broke KSZ9031. To fix this configure the
KSZ9031 PHY driver to use genphy_soft_reset.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding checks to detect wrong usage of the phylib API we added
a check to phy_start_aneg() which is too strict. If the phylib
state machine is in state PHY_HALTED we should allow reconfiguring
and restarting aneg, and just don't touch the state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff5 ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers can use this as .ndo_change_carrier() to change carrier
via /sys/class/net/ethX/carrier.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 6390 Ethernet switch family does not perform MDIO
turnaround correctly. Many hardware MDIO bus masters don't care about
this, but the bitbangging implementation in Linux does by default. Add
phy_ignore_ta_mask to the platform data so that the bitbangging code
can be told which devices are known to get TA wrong.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is sometimes necessary to instantiate a bit-banging MDIO bus as a
platform device, without the aid of device tree.
When device tree is being used, the bus is not scanned for devices,
only those devices which are in device tree are probed. Without device
tree, by default, all addresses on the bus are scanned. This may then
find a device which is not a PHY, e.g. a switch. And the switch may
have registers containing values which look like a PHY. So during the
scan, a PHY device is wrongly created.
After the bus has been registered, a search is made for
mdio_board_info structures which indicates devices on the bus, and the
driver which should be used for them. This is typically used to
instantiate Ethernet switches from platform drivers. However, if the
scanning of the bus has created a PHY device at the same location as
indicated into the board info for a switch, the switch device is not
created, since the address is already busy.
This can be avoided by setting the phy_mask of the mdio bus. This mask
prevents addresses on the bus being scanned.
v2
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MII_ADVERTISE register is modified by the IOCTL handler,
phydev->advertising needs recalculating. Use the _mod_ variant of
mii_adv_to_linkmode_adv_t so that bits outside of the advertise
registers are not cleared.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a _mod_ variant of mii_lpa_to_linkmode_lpa_t. Use this to fix the
genphy_read_status() where the 1G link partner features are getting
lost.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_lpa_to_linkmode_lpa_t to mii_lpa_mod_linkmode_lpa_t to
indicate it modifies the passed linkmode bitmap, without clearing any
other bits.
Also, ensure bit are clear which the lpa indicates should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.
Add a helper to set/clear bits in a linkmode.
Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.
Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
ef1b5bf506 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b812 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Logic of phy_device_create() requests PHY modules according to PHY ID
but for C45 PHYs we use different field for the IDs.
Let's also request the modules for these IDs.
Changes from v1:
- Only request C22 modules if C45 are not present (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joao Pinto <joao.pinto@synopsys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77a ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far the two functions consider neither member eee_enabled nor
eee_active. Therefore network drivers have to do this in some kind
of glue code. I think this can be avoided.
Getting EEE parameters:
When not advertising any EEE mode, we can't consider EEE to be enabled.
Therefore interpret "EEE enabled" as "we advertise at least one EEE
mode". It's similar with "EEE active": interpret it as "EEE modes
advertised by both link partner have at least one mode in common".
Setting EEE parameters:
If eee_enabled isn't set, don't advertise any EEE mode and restart
aneg if needed to switch off EEE. If eee_enabled is set and
data->advertised is empty (e.g. because EEE was disabled), advertise
everything we support as default. This way EEE can easily switched
on/off by doing ethtool --set-eee <if> eee on/off, w/o any additional
parameters.
The changes to both functions shouldn't break any existing user.
Once the changes have been applied, at least some users can be
simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link modes that sfp_parse_support() detects are stored in the
'modes' bitmap. There is no reason to make an exception for 1000Base-PX
or 1000Base-BX10.
Fixes: 03145864bd ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
After switching the r8169 driver to use phylib some user reported that
their network is broken. This was caused by the genphy PHY driver being
used instead of the dedicated PHY driver for the RTL8211B. Users
reported that loading the Realtek PHY driver module upfront fixes the
issue. See also this mail thread:
https://marc.info/?t=154279781800003&r=1&w=2
The issue is quite weird and the root cause seems to be somewhere in
the base driver core. The patch works around the issue and may be
removed once the actual issue is fixed.
The Fixes tag refers to the first reported occurrence of the issue.
The issue itself may have been existing much longer and it may affect
users of other network chips as well. Users typically will recognize
this issue only if their PHY stops working when being used with the
genphy driver.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsc85xx_default_config function called in the vsc85xx_config_init
function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
mistakenly calls phy_read and phy_write in-between phy_select_page and
phy_restore_page.
phy_select_page and phy_restore_page actually take and release the MDIO
bus lock and phy_write and phy_read take and release the lock to write
or read to a PHY register.
Let's fix this deadlock by using phy_modify_paged which handles
correctly a read followed by a write in a non-standard page.
Fixes: 6a0bfbbe20 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A more featureful support for VSC8574 was recently added to the
Microsemi (mscc.c) driver. I checked that features supported in the
Vitesse driver are also supported in the Microsemi driver.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
By default the PHY is configured to output the "receive error" status on
pin 21. Depending on the board layout and requirements we may want to
re-configure the PHY to output the interrupt signal there.
The mode of pin 21 can be configured in the "Digital I/O Specific
Control Register" (register 29), bit 2:
- 0 = RXER function
- 1 = INTR(32) function
Depending on the devicetree configuration we will now:
- change the mode to either ther RXER or INTR32 function
- keep the SEL_INTR32 value set by the bootloader (default) if no
configuration is provided (to ensure that we're not breaking existing
boards)
- error out if conflicting configuration is given (RXER and INTR32 mode
are enabled at the same time)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.
This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
error)
- the PHY's interrupt line is configured "active low" by default
Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheet uses the name "All Mask" for this bit. Change the name of
our #define to be consistent with the datasheet. While here also replace
the tab between the #define and IP101A_G_IRQ_ALL_MASK with a space.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code consistent by using the BIT() macro instead of
manual bit-shifting for some of the fields. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply moves ip101a_g_config_init right above
ip101a_g_config_intr so all functions for the ICPlus IP101A/G PHYs are
grouped together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit 2d6c9091ab ("net: mdio-gpio: support access that
may sleep") and got lost by commit 7e5fbd1e07 ("net: mdio-gpio:
Convert to use gpiod functions where possible").
Also add a warning about slow GPIO pins like it is done in i2c-gpio.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the icplus driver has been fixed all PHY drivers supporting
interrupts have both callbacks (config_intr and ack_interrupt)
implemented - as it should be. Therefore phy_drv_supports_irq()
can be changed now to check for both callbacks being implemented.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move IRQ configuration for IP101A/G from config_init to config_intr
callback. Reasons:
1. This allows phylib to disable interrupts if needed.
2. Icplus was the only driver supporting interrupts w/o defining a
config_intr callback. Now we can add a phylib plausibility check
disabling interrupt mode if one of the two irq-related callbacks
isn't defined.
I don't own hardware with this PHY, and the change is based on the
datasheet for IP101A LF (which is supposed to be register-compatible
with IP101A/G). Change is compile-tested only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change modified variable advertising from a u32 to a link mode
array and left the u32 zero comparison, so essential we now have an array
being compared to null which is not the intention. Fix this by using the
call to linkmode_empty to check if advertising is all zero.
Detected by CoverityScan, CID#1475424 ("Array compared against 0")
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/phy/marvell.c: In function 'm88e1510_config_init':
drivers/net/phy/marvell.c:850:7: warning:
variable 'pause' set but not used [-Wunused-but-set-variable]
It not used any more after commit 3c1bcc8614 ("net: ethernet: Convert phydev
advertize and supported from u32 to link mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that 2.5G and 5G can be represented in phydev->advertising and
phydev->lp_advertising, add these two links modes as possible
resolutions to auto negotiation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that PHYs and MAC can support more than 32 bit masks, add link
modes which are > 31 to the PHY settings table.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both states aren't used. Most likely they result from an idea that
never materialized. So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new macros for PHYID matching to avoid boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that phy_mac_interrupt() doesn't call phy_change() any longer it's
called from phy_interrupt() only. Therefore phy_interrupt_is_valid()
returns true always and the check can be removed.
In case of PHY_HALTED phy_interrupt() bails out immediately,
therefore the second check for PHY_HALTED including the call to
phy_disable_interrupts() can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using phy_mac_interrupt() the irq number is set to
PHY_IGNORE_INTERRUPT, therefore phy_interrupt_is_valid() returns false.
As a result phy_change() effectively just calls phy_trigger_machine()
when called from phy_mac_interrupt() via phy_change_work(). So we can
call phy_trigger_machine() from phy_mac_interrupt() directly and
remove some now unneeded code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State PHY_CHANGELINK isn't needed here, we can call the state machine
directly. We just have to remove the check for phy_polling_mode() to
make this work also in interrupt mode. Removing this check doesn't
cause any overhead because when not polling the state machine is
called only if required by some event.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flag PHY_HAS_INTERRUPT is used only here for this small check. I think
using interrupts isn't possible if a driver defines neither
config_intr nor ack_interrupts callback. So we can replace checking
flag PHY_HAS_INTERRUPT with checking for these callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy core provides a handy phy_speed_to_str() helper, so use that
instead of doing our own formatting of the different known link speeds.
To do this, increase PHY_LED_TRIGGER_SPEED_SUFFIX_SIZE to 11 so we can fit
'Unsupported' if necessary.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a heritage from the very early days of phylib member interrupts is
defined as u32 even though it's just a flag whether interrupts are
enabled. So we can change it to a bitfield member. In addition change
the code dealing with this member in a way that it's clear we're
dealing with a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_check_link_status in more places in the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes in the state machine state PHY_AN isn't used
any longer and can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
