ctx->conf.radar_enabled should reflect whether radar
detection is enabled for the channel context.
When calculating it, make it consider only the vifs
that have this context assigned (instead of all the
vifs).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
local->radar_detect_enabled should tell whether
radar_detect is enabled on any interface belonging
to local.
However, it's not getting updated correctly
in many cases (actually, when testing with hwsim
it's never been set, even when the dfs master
is beaconing).
Instead of handling all the corner cases
(e.g. channel switch), simply check whether
radar detection is enabled only when needed,
instead of caching the result.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the channel switch has been made, a vif is now using
the channel context which was reserved. When that happens,
we need to update the channel context since its parameters
may change.
I hit a case in which I switched to a 40Mhz channel but the
reserved channel context was still on 20Mhz. The rate control
would try to send 40Mhz packets on a 20Mhz channel context and
that made iwlwifi's firmware unhappy.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of keeping track of all those special cases where
VLAN interfaces have no bss_conf.chandef, just make sure
they have the same as the AP interface they belong to.
Among others, this fixes a crash getting a VLAN's channel
from userspace since a NULL channel is returned as a good
result (return value 0) for VLANs since the commit below.
Cc: stable@vger.kernel.org [3.18 only]
Fixes: c12bc4885f ("mac80211: return the vif's chandef in ieee80211_cfg_get_channel()")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds 802.11p OCB (Outside the Context of a BSS) mode
support.
When communicating in OCB mode a mandatory wildcard BSSID
(48 '1' bits) is used.
The EDCA parameters handling function was changed to support
802.11p specific values.
The insertion of a newly discovered STAs is done in the similar way
as in the IBSS mode -- through the deferred insertion.
The OCB mode uses a periodic 'housekeeping task' for expiration of
disconnected STAs (in the similar manner as in the MESH mode).
New Kconfig option for verbose OCB debugging outputs is added.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use codespell to find spelling errors.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs.
-----BEGIN PGP SIGNATURE-----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=G/pB
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
When a device driver is unloaded local->interfaces
list is cleared. If there was more than 1
interface running and connected (bound to a
chanctx) then chantype recalc was called and it
ended up with compat being NULL causing a call
trace warning.
Warn if compat becomes NULL as a result of
incompatible bss_conf.chandef of interfaces bound
to a given channel context only.
The call trace looked like this:
WARNING: CPU: 2 PID: 2594 at /devel/src/linux/net/mac80211/chan.c:557 ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0()
Modules linked in: ath10k_pci(-) ath10k_core ath
CPU: 2 PID: 2594 Comm: rmmod Tainted: G W 3.16.0-rc1+ #150
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
0000000000000009 ffff88001ea279c0 ffffffff818dfa93 0000000000000000
ffff88001ea279f8 ffffffff810514a8 ffff88001ce09cd0 ffff88001e03cc58
0000000000000000 ffff88001ce08840 ffff88001ce09cd0 ffff88001ea27a08
Call Trace:
[<ffffffff818dfa93>] dump_stack+0x4d/0x66
[<ffffffff810514a8>] warn_slowpath_common+0x78/0xa0
[<ffffffff81051585>] warn_slowpath_null+0x15/0x20
[<ffffffff818a407d>] ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0
[<ffffffff818a3dda>] ? ieee80211_recalc_chanctx_chantype+0x2a/0x2e0
[<ffffffff818a4919>] ieee80211_assign_vif_chanctx+0x1a9/0x770
[<ffffffff818a6220>] __ieee80211_vif_release_channel+0x70/0x130
[<ffffffff818a6dd3>] ieee80211_vif_release_channel+0x43/0xb0
[<ffffffff81885f4e>] ieee80211_stop_ap+0x21e/0x5a0
[<ffffffff8184b9b5>] __cfg80211_stop_ap+0x85/0x520
[<ffffffff8181c188>] __cfg80211_leave+0x68/0x120
[<ffffffff8181c268>] cfg80211_leave+0x28/0x40
[<ffffffff8181c5f3>] cfg80211_netdev_notifier_call+0x373/0x6b0
[<ffffffff8107f965>] notifier_call_chain+0x55/0x110
[<ffffffff8107fa41>] raw_notifier_call_chain+0x11/0x20
[<ffffffff816a8dc0>] call_netdevice_notifiers_info+0x30/0x60
[<ffffffff816a8eb9>] __dev_close_many+0x59/0xf0
[<ffffffff816a9021>] dev_close_many+0x81/0x120
[<ffffffff816aa1c5>] rollback_registered_many+0x115/0x2a0
[<ffffffff816aa3a6>] unregister_netdevice_many+0x16/0xa0
[<ffffffff8187d841>] ieee80211_remove_interfaces+0x121/0x1b0
[<ffffffff8185e0e6>] ieee80211_unregister_hw+0x56/0x110
[<ffffffffa0011ac4>] ath10k_mac_unregister+0x14/0x60 [ath10k_core]
[<ffffffffa0014fe7>] ath10k_core_unregister+0x27/0x40 [ath10k_core]
[<ffffffffa003b1f4>] ath10k_pci_remove+0x44/0xa0 [ath10k_pci]
[<ffffffff81373138>] pci_device_remove+0x28/0x60
[<ffffffff814cb534>] __device_release_driver+0x64/0xd0
[<ffffffff814cbcc8>] driver_detach+0xb8/0xc0
[<ffffffff814cb23a>] bus_remove_driver+0x4a/0xb0
[<ffffffff814cc697>] driver_unregister+0x27/0x50
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When bringing down the AP, a WARN_ON is hit because the bss config chandef
is empty here.
Since AP_VLAN channel settings do not matter for anything chanctx related
(always inherits the settings from the AP interface), let's just ignore
it here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new_ctx pointer is set only for non-chanctx drivers. This yielded a
crash for chanctx-based drivers during channel switch finalization:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]
Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When lockdep isn't compiled, a local variable isn't used
(it's only in a macro argument), annotate it to suppress
the compiler warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch finalization is now 2-step. First
step is when driver calls chswitch_done(), the
other is when reservation is actually finalized
(which be defered for in-place reservation).
It is now safe to call ieee80211_chswitch_done()
more than once.
Also remove the ieee80211_vif_change_channel()
because it is no longer used.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch finalization is now 2-step. First
step is when driver calls csa_finish(), the other
is when reservation is actually finalized (which
can be deferred for in-place reservation).
It is now safe to call ieee80211_csa_finish() more
than once.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.
Such reservations are not finalized until all
assigned interfaces are ready.
This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'local' variable in __ieee80211_vif_copy_chanctx_to_vlans()
is only used/needed when lockdep is compiled in, mark it as such
to avoid compile warnings in the other case.
While at it, fix some indentation where it's used.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't make much sense to store refcount in
the chanctx structure. One still needs to hold
chanctx_mtx to get the value safely. Besides,
refcount isn't on performance critical paths.
This will make implementing chanctx reservation
refcounting a little easier.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function did a little too much. Split it up so
the code can be easily reused in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function did a little too much. Split it up so
the code can be easily reused in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a separate function to look for reservation
chanctx. For multi-interface/channel reservation
search sematics differ slightly.
The new routine allows reservations to be merged
with chanctx that are already reserved by other
interface(s).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows new vifs to be assigned to a chanctx
as long as chanctx's reservation chandefs (if any)
and chanctx's current chandef (implied by assigned
vifs at the time, if any) and the new vif chandef
are all compatible.
This implies it is impossible to assign a new vif
to an in-place reservation chanctx.
This gives no advantages for single-channel
hardware. It makes sense for multi-channel
hardware only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful. Provides a more straghtforward
way to iterate over interfaces taking part in
chanctx reservation and allows tracking chanctx
usage explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful. Provides a more straghtforward
way to iterate over interfaces bound to a given
chanctx and allows tracking chanctx usage
explicitly.
The structure is protected by local->chanctx_mtx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initial chanctx reservation code wasn't aware of
radar detection requirements. This is necessary
for chanctx reservations to be used for channel
switching in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not allocate more channel contexts than a
driver is capable for currently matching interface
combination.
This allows the ieee80211_vif_reserve_chanctx() to
act as a guard against breaking interface
combinations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With single-channel drivers, we need to be able to change a running
chanctx if we want to use chanctx reservation. Not all drivers may be
able to do this, so add a flag that indicates support for it.
Changing a running chanctx can also be used as an optimization in
multi-channel drivers when the context needs to be reserved for future
usage.
Introduce IEEE80211_CHANCTX_RESERVED chanctx mode to mark a channel as
reserved so nobody else can use it (since we know it's going to
change). In the future, we may allow several vifs to use the same
reservation as long as they plan to use the chanctx on the same
future channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support channel switch with multiple vifs and multiple
contexts, we implement a concept of channel context reservation. This
allows us to reserve a channel context to be used later.
The reservation functionality is not tied directly to channel switch
and may be used in other situations (eg. reserving a channel context
during IBSS join).
We first check if an existing compatible context exists and if it
does, we reserve it. If there is no compatible context we create a
new one and reserve it.
Additionally, split ieee80211_vif_copy_chanctx_to_vlans() so we can
call it while already holding the chanctx mutex.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Combine the functions into one, so that we can switch from one context
to the other without having to unassign and assign separately. This
is needed by the channel reservation functionality because otherwise
we have a small period of time when the chanctx is set to NULL, which
can cause problems if someone else is trying to dereference it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_vif_change_channel() locks chanctx_mtx. When implementing
channel reservation for CS, we will need to call the function to
change channel when the lock is already held, so split the part that
requires the lock out and leave the locking in the original function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was impossible to change chanctx of master AP
for AP VLANs because the copy function requires
RTNL which can't be simply taken in mac80211 code
due to possible deadlocks.
This is required for future chanctx reservation
that re-bind vifs to new chanctx. This requires
safe AP VLAN iteration without RTNL.
Now VLANs can be iterated while holding either
RTNL or local->mtx because the list is modified
while holding both of these locks.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counting part of the interface combination check from
cfg80211 to mac80211.
This is needed to simplify locking when the driver has to perform a
combination check by itself (eg. with channel-switch).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rcu_assign_pointer() ensures that the initialization of a structure is
carried out before storing a pointer to that structure. However, in the
case that NULL is assigned there's no structure to initialize so using
RCU_INIT_POINTER instead is safe and more efficient.
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
[squash eight tiny patches, rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If chandef had non-HT width it was possible for
radar_enabled update to not be propagated properly
through drv_config(). This happened because
ieee80211_hw_conf_chan() would never see different
local->hw.conf.chandef and local->_oper_chandef.
This wasn't a problem with HT chandefs because
_oper_chandef width is reset to non-HT in
ieee80211_free_chanctx() making
ieee80211_hw_conf_chan() to kick in.
This problem led (at least) ath10k to not start
CAC if prior CAC was cancelled and both CACs were
requested for identical non-HT chandefs.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All antennas should be operational when monitoring to maximize
reception.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating the current max bw required for
a channel context, we didn't consider the virtual
monitor interface, resulting in its channel context
being narrower than configured.
This broke monitor mode with iwlmvm, which uses the
minimal width.
Reported-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
radar_required setting wasn't protected by
local->mtx in some places. This should prevent
from scanning/radar detection/roc colliding.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scan code creates an iflist_mtx -> mtx locking dependency,
and a few other places, notably radar detection, were creating
the opposite dependency, causing lockdep to complain. As scan
and radar detection are mutually exclusive, the deadlock can't
really happen in practice, but it's still bad form.
A similar issue exists in the monitor mode code, but this is
only used by channel-context drivers right now and those have
to have hardware scan, so that also can't happen.
Still, fix these issues by making some of the channel context
code require the mtx to be held rather than acquiring it, thus
allowing the monitor/radar callers to keep the iflist_mtx->mtx
lock ordering.
While at it, also fix access to the local->scanning variable
in the radar code, and document that radar_detect_enabled is
now properly protected by the mtx.
All this would now introduce an ABBA deadlock between the DFS
work cancelling and local->mtx, so change the locking there a
bit to not need to use cancel_delayed_work_sync() but be able
to just use cancel_delayed_work(). The work is also safely
stopped/removed when the interface is stopped, so no extra
changes are needed.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is only used in one file, so move it up a
bit to avoid forward declarations and make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new field to ieee80211_chanctx_conf to indicate
the min required channel configuration.
Tuning to a narrower channel might help reducing
the noise level and saving some power.
The min required channel definition is the max of
all min required channel definitions of the interfaces
bound to this channel context.
In AP mode, use 20MHz when there are no connected station.
When a new station is added/removed, calculate the new max
bandwidth supported by any of the stations (e.g. 80MHz when
80MHz and 40MHz stations are connected).
In other cases, simply use bss_conf.chandef as the
min required chandef.
Notify drivers about changes to this field by calling
drv_change_chanctx with a new CHANGE_MIN_WIDTH notification.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no reason why we should have only one channel switch
announcement at a time for a single phy. When support for channel
switch with multiple contexts and multiple vifs per context is
implemented, we will need the chandef data for each vif. Move the
csa_chandef structure to sdata to prepare for this.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[Fixed compilation with mesh]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Limit the current implementation to a single channel context used by
a single vif, thereby avoiding multi-vif/channel complexities.
Reuse the main function from AP CSA code, but move a portion out in
order to fit the STA scenario.
Add a new mac80211 HW flag so we don't break devices that don't support
channel switch with channel-contexts. The new behavior will be opt-in.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
local->hw.conf maybe not be synced when recalcing whether radar is
enabled, sometimes leaving radar enabled even if it's not neccesary
anymore.
Fix this by:
* setting radar_enabled when creating the chanctx
* turning radar_enabled off before destroying the last channel context
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
