This patch adds driver for IR controller on MT7623 SoC.
and should also work on similar Mediatek SoC. Currently
testing successfully on NEC and SONY remote controller
only but it should work on others (lirc, rc-5 and rc-6).
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver was written using lirc since rc-core did not support
transmitter-only hardware at that time. Now that it does, port
this driver.
Compile tested only.
Signed-off-by: Sean Young <sean@mess.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ir-spi is a simple device driver which supports the
connection between an IR LED and the MOSI line of an SPI device.
The driver, indeed, uses the SPI framework to stream the raw data
provided by userspace through an rc character device. The chardev
is handled by the LIRC framework and its functionality basically
provides:
- write: the driver gets a pulse/space signal and translates it
to a binary signal that will be streamed to the IR led through
the SPI framework.
- set frequency: sets the frequency whith which the data should
be sent. This is handle with ioctl with the
LIRC_SET_SEND_CARRIER flag (as per lirc documentation)
- set duty cycle: this is also handled with ioctl with the
LIRC_SET_SEND_DUTY_CYCLE flag. The driver handles duty cycles
of 50%, 60%, 70%, 75%, 80% and 90%, calculated on 16bit data.
The character device is created under /dev/lircX name, where X is
and ID assigned by the LIRC framework.
Example of usage:
fd = open("/dev/lirc0", O_RDWR);
if (fd < 0)
return -1;
val = 608000;
ret = ioctl(fd, LIRC_SET_SEND_CARRIER, &val);
if (ret < 0)
return -1;
val = 60;
ret = ioctl(fd, LIRC_SET_SEND_DUTY_CYCLE, &val);
if (ret < 0)
return -1;
n = write(fd, buffer, BUF_LEN);
if (n < 0 || n != BUF_LEN)
ret = -1;
close(fd);
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ir-rx51 driver for n900 has been disabled since the multiarch
changes as plat include directory no longer is SoC specific.
Let's fix it with minimal changes to pass the dmtimer calls in
pdata. Then the following changes can be done while things can
be tested to be working for each change:
1. Change the non-pwm dmtimer to use just hrtimer if possible
2. Change the pwm dmtimer to use Linux PWM API with the new
drivers/pwm/pwm-omap-dmtimer.c and remove the direct calls
to dmtimer functions
3. Parse configuration from device tree and drop the pdata
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Denon also uses the Sharp protocol, however with different check bits.
It would have been also possible to add this as a separate protocol
but this may not be worth the effort.
Successfully tested with a Denon RC-1002 remote control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RC_ST and IR_SUNXI entries have weird indentation, and the RC_ST
entry is actually malformed. Fix it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Amlogic Meson SoCs include a infrared remote control receiver that can
operate in two modes: "NEC" mode in which the hardware decodes frames
using the NEC IR protocol, and "general" mode in which the receiver
simply reports the duration of pulses and spaces for software
decoding.
This is a driver for the IR receiver that implements software decoding
of received frames.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a complete re-write inspired by the original lirc driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
IR transmitter driver for Hisilicon hix5hd2 soc
By default all protocols are disabled.
For example nec decoder can be enabled by either
1. ir-keytable -p nec
2. echo nec > /sys/class/rc/rc0/protocols
See see Documentation/ABI/testing/sysfs-class-rc
[mchehab@osg.samsung.com: Add a fixup for the driver to compile on
archs that don't provide writel_relaxed() macro]
Signed-off-by: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several arch-specific media drivers that don't
require asm-specific includes and can be successfully
compiled on x86. Add COMPILE_TEST dependency for them, in
order to allow a broader test on those drivers.
That helps static analysis tools like Coverity to discover
eventual troubles there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This protocol is found on Dreambox remotes
[m.chehab@samsung.com: CodingStyle fixes and conflict fix]
Signed-off-by: Marcel Mol <marcel@mesa.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the protocol is part of the scancode, it is pretty easy to merge
the rc5 and streamzap decoders. An additional advantage is that the decoder
is now stricter as it waits for the trailing silence before determining that
a command is a valid rc5/streamzap command (which avoids collisions that I've
seen with e.g. Sony protocols).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds driver for sunxi IR controller.
It is based on Alexsey Shestacov's work based on the original driver
supplied by Allwinner.
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: Alexsey Shestacov <wingrime@linux-sunxi.org>
[hdegoede@redhat.com: Changed compatible to sun4i-a10-ir]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add ImgTec IR decoder driver to the build system.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a raw decoder for the Sharp protocol. It uses a pulse distance
modulation with a pulse of 320us and a bit period of 2ms for a logical 1
and 1ms for a logical 0. The first part of the message consists of a
5-bit address, an 8-bit command, and two other bits, followed by a 40ms
gap before the echo message which is an inverted version of the main
message except for the address bits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support to ST RC driver, which is basically a IR/UHF
receiver and transmitter. This IP (IRB) is common across all the ST
parts for settop box platforms. IRB is embedded in ST COMMS IP block.
It supports both Rx & Tx functionality.
This driver adds only Rx functionality via LIRC codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Note that with the rc-feedback trigger, the cir-rx trigger is now
redundant. The cir-tx trigger is not used by default; if this
functionality is desired then it should exist in rc-core, not in
a driver.
Also make sure that the led is suspended on suspend.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver can be enabled on OMAP1 at the moment, which breaks
allyesconfig for that platform. Let's mark it OMAP2PLUS-only
in Kconfig, since that is the only thing it builds on.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We still need to fix up few places for multiplatform support,
but that can proceed separately. Fix the issue by making the
problem drivers depends !ARCH_MULTIPLATFORM for now.
The remaining pieces that are not multiplatform compatible
for omap2+ SoCs are:
1. Some drivers are using custom omap_dm_timer calls
There are two drivers that are directly usign omap hardware
timers for PWM and DSP clocking: drivers/media/rc/ir-rx51.c and
drivers/staging/tidspbridge/core/dsp-clock.c. These can be
fixed for multiplatform by allowing a minimal set of hardware
timers to be accessed, and for some functionality by using the
hrtimer framework.
2. Hardware OMAP4_ERRATA_I688 needs to be fixed up
This can't be enabled for multiplatform configurations in
it's current form. It may be possible to fix it up to do
instruction replacement early on during init. Luckily it
looks like this errata does not seem to get hit with
mainline kernel code alone at least currently.
3. Legacy header needed for omap-sham.c
Looks like it still needs mach/irqs.h for omap1 that
does not exist for multiplatform systems. Just ifdef
it for now.
4. Mailbox is waiting to get moved to drivers
Disable it for now to avoid adding a dependency to the
mailbox patches.
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Sean Young <sean@mess.org>
Cc: "Víctor Manuel Jáquez Leal" <vjaquez@igalia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[tony@atomide.com: updated to disable mailbox]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although this kind of IR diode circuitry is known to exist only in
N900 hardware, nothing prevents making similar circuitry on any OMAP
based board. The MACH_NOKIA_RX51 dependency is thus not something we
want to be there.
Also, this should depend on LIRC as it is a LIRC driver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Fix typo
-Change pwm_timer_num type to match type in platform data
-Remove extra parenthesis
-Replace magic constant with proper bit defintions
-Remove duplicate exit pointer
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQNUEyAAoJEHm+PkMAQRiGs+sH/iLtdAVcfBfUwdmGV0qDXbVE
L3gCg3IERPCSaQo8qsT3zujdLAQ2HsiMs73jbqJaBWSV16ZMqkglRKbn+QMGpqJV
bi/pf5Akrm9IL/u+427ycB8QxzyjGal8uJ6btuwXa03VROSfOsEiQbtsByFNaDv/
8oq0/DaE8mWRedlcAaeN+l8nD4Enb2jSKp0UADkBMnUr4KCbwSVQ+ITXAggqVq23
htA3Yt0oGf1JYq+k99D5k92h0I/4VwiorUgwPKhmS5DM9gVtJ4L+SigbekS/MFq+
huyzOHRWlO++OxBlgSTMuJAE1k/G2B7tGeoERY0tEL/hAWcKYTfGIXSc7X6JvM0=
=Dmsv
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc3' into staging/for_v3.7
Linux 3.6-rc3
* tag 'v3.6-rc3': (764 commits)
Linux 3.6-rc3
task_work: add a scheduling point in task_work_run()
fs: fix fs/namei.c kernel-doc warnings
eventpoll: use-after-possible-free in epoll_create1()
vfio: grab vfio_device reference *before* exposing the sucker via fd_install()
vfio: get rid of vfio_device_put()/vfio_group_get_device* races
vfio: get rid of open-coding kref_put_mutex
introduce kref_put_mutex()
vfio: don't dereference after kfree...
fbcon: fix race condition between console lock and cursor timer (v1.1)
mm: compaction: Abort async compaction if locks are contended or taking too long
mm: have order > 0 compaction start near a pageblock with free pages
rapidio/tsi721: fix unused variable compiler warning
rapidio/tsi721: fix inbound doorbell interrupt handling
drivers/rtc/rtc-rs5c348.c: fix hour decoding in 12-hour mode
mm: correct page->pfmemalloc to fix deactivate_slab regression
drivers/rtc/rtc-pcf2123.c: initialize dynamic sysfs attributes
mm/compaction.c: fix deferring compaction mistake
drivers/misc/sgi-xp/xpc_uv.c: SGI XPC fails to load when cpu 0 is out of IRQ resources
string: do not export memweight() to userspace
...
This is the driver for the IR transmitter diode found on the Nokia
N900 (also known as RX51) device. The driver is mostly the same as
found in the original 2.6.28 based kernel that comes with the device.
The following modifications have been made compared to the original
driver version:
- Adopt to the changes that has happen in the kernel during the past
five years, such as the change in the include paths
- The OMAP DM-timers require much more care nowadays. The timers need
to be enabled and disabled or otherwise many actions fail. Timers
must not be freed without first stopping them or otherwise the timer
cannot be requested again.
The code has been tested with sending IR codes with N900 device
running Debian userland. The device receiving the codes was Anysee
DVB-C USB receiver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver adds support for TechnoTrend USB IR Receiver. It is a complete
rewrite of the staging/media/lirc/lirc_ttusbir driver. It adds more
accurate sample reporting and led control.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware versions lower than 0x0205 use a different interface which is not
supported. Also report the firmware version in the standard format.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the error
drivers/usb/core/hub.c:3753: undefined reference to `usb_speed_string'
seen in various random configurations.
Cc: Sean Young <sean@mess.org>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Better arrange the remote controller driver items to happen after the
core support, on their proper menus, and making clerarer what is media
core options and what is media driver options.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the main items to:
<m> Multimedia support --->
[ ] Cameras/video grabbers support
[ ] Analog TV support
[ ] Digital TV support
[ ] AM/FM radio receivers/transmitters support
[ ] Remote Controller support
This provides an interface that is clearer to end users that
are compiling the Kernel, and will allow the building system
to automatically unselect drivers for unused functions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR sony decoder is making use of 'bitrev8' that,
in turn, requires BITREVERSE.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds GPIO based IR Receiver driver. It decodes signals using decoders
available in rc framework.
Signed-off-by: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The keycode mangling algorithm is kept the same, so the new external
keymap has the same values as the old static table.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver will be migrated to the RC driver API in a following
commit.
[mchehab@redhat.com: Fix some bad whitespacing]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a custom IR protocol decoder, for the RC-6-ish protocol used by
the Microsoft Remote Keyboard, apparently developed internally at
Microsoft, and officially dubbed MCIR-2, per their March 2011 remote and
transceiver requirements and specifications document, which also touches
on this IR keyboard/mouse device.
Its a standard keyboard with embedded thumb stick mouse pointer and
mouse buttons, along with a number of media keys. The media keys are
standard RC-6, identical to the signals from the stock MCE remotes, and
will be handled as such. The keyboard and mouse signals will be decoded
and delivered to the system by an input device registered specifically
by this driver.
Successfully tested with multiple mceusb-driven transceivers, as well as
with fintek-cir and redrat3 hardware. Essentially, any raw IR hardware
with enough sampling resolution should be able to use this decoder,
nothing about it is at all receiver-hardware-specific.
This work is inspired by lirc_mod_mce:
The documentation there and code aided in understanding and decoding the
protocol, but the bulk of the code is actually borrowed more from the
existing in-kernel decoders than anything. I did recycle the keyboard
keycode table, a few defines, and some of the keyboard and mouse data
parsing bits from lirc_mod_mce though.
Special thanks to James Meyer for providing the hardware, and being
patient with me as I took forever to get around to writing this.
callback routine to ensure we don't get any stuck keys, and used
symbolic names for the keytable. Also cc'ing Florian this time, who I
believe is the original mod-mce author...
CC: Florian Demski <fdemski@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new driver for the Fintek LPC SuperIO CIR function, in the
Fintek F71809 chip. Hardware and datasheets were provided by Fintek, so
thanks go to them for supporting this effort.
This driver started out as a copy of the nuvoton-cir driver, and was
then modified as needed for the Fintek chip. The two share many
similaries, though the buffer handling for the Fintek chip is actually
nearly identical to the mceusb buffer handling, so the parser routine is
almost a drop-in copy of the mceusb buffer parser (a candidate for being
abstracted out into shared code at some point).
This initial code drop *only* supports receive, but the hardware does
support transmit as well. I really haven't even started to look at
what's required, but my guess is that its also pretty similar to mceusb.
Most people are probably only really interested in RX anyway though, so
I think its good to get this out there even with only RX.
(Nb: there are also Fintek-made mceusb receivers, which presumably, this
chip shares CIR hardware with).
This hardware can be found on at least Jetway NC98 boards and derivative
systems, and likely others as well. Functionality was tested with an
NC98 development board, in-kernel decode of RC6 (mce), RC5 (hauppauge)
and NEC-ish (tivo) remotes all successful, as was lirc userspace decode
of the RC6 remote.
CC: Aaron Huang <aaron_huang@fintek.com.tw>
CC: Tom Tsai <tom_tsai@fintek.com.tw>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new rc-core device driver for the IR transceivers made by
RedRat Ltd. (http://redrat.co.uk/). It started out life as an
out-of-lirc-tree lirc driver, maintained in its own repo on sourceforge,
by Stephen Cox. He started porting it to what was then ir-core, and I
finally picked it up about two week ago and did a fairly large overhaul
on it, and its now into a state where I'm fairly comfortable submitting
it here for review and inclusion in the kernel. I'm claiming authorship
of this driver, since while it started out as Stephen's work, its
definitely a derivative work now, at 876 lines added and 1698 lines
removed since grabbing it from sourceforge. Stephen's name is retained
as secondary author though, and credited in the headers. Those
interested in seeing how the changes evolved can (at least for now) look
at this branch in my git tree:
http://git.kernel.org/?p=linux/kernel/git/jarod/linux-2.6-ir.git;a=shortlog;h=refs/heads/redrat3
That won't be around forever though, and I'm doing this as a single
commit to go into mainline. Anyway...
I've successfully tested in-kernel decode of rc5, rc6 and nec remotes,
as well as lirc userspace decode of rc5 and rc6. There are still some
quirks here to sort out with rc5 lirc userspace decode, but I'm working
with the RedRat folks themselves to figure out what's going on there
(rc5 lirc decode works, but you only get an event on key release --
in-kernel rc5 decode behaves perfectly fine). Note that lirc decode of
rc6 is working perfectly. Transmit is also working, tested by pointing
the redrat3 at an mceusb transceiver, which happily picked up the
transmitted signals and properly decoded them.
There's no default remote for this hardware, so its somewhat arbitrarily
set to use the Hauppauge RC5 keymap by default. Easily changed out by
way of ir-keytable and irrelevant if you're using lircd for decode.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <Andrew.Vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a second version of an rc-core based driver for the ITE Tech IT8712F
CIR and now for a pair of other variants of the IT8512 CIR too.
This driver should replace the lirc_it87 and lirc_ite8709 currently living in
the LIRC staging directory.
The driver should support the ITE8704, ITE8713, ITE8708 and ITE8709 (this last
one yet untested) PNP ID's.
The code doesn'te reuse code from the pre-existing LIRC drivers, but has been
written from scratch using the nuvoton.cir driver as a skeleton.
This new driver shouldn't exhibit timing problems when running under load (or
with interrupts disabled for relatively long times). It works OOTB with the
RC6 MCE remote bundled with the ASUS EEEBox. TX support is implemented, but
I'm unable to test it since my hardware lacks TX capability.
Signed-off-by: Juan J. Garcia de Soria <skandalfo@gmail.com>
Tested-by: Stephan Raue <stephan@openelec.tv>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a loopback driver to rc-core which I've found useful for
running scripted tests of different parts of rc-core without having to
fiddle with real hardware.
Basically it emulates hardware with a learning and a non-learning
receiver and two transmitters (which correspond to the two
receivers). TX data that is sent is fed back as input on the
corresponding receiver, which allows for debugging of IR decoders,
keymaps, etc.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h
To be consistent with the other changes.
No functional change on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Something weird happened with commit 740069e6e043403199dbe2b42256722fb814f6ae.
Instead of dong the right thing, it got somehow corrupted and reverted the
rc changes.
Thanks to David Härdeman for pointing me about the problem.
This patch should be merged with 740069e6e04 before sending upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move winbond-cir from drivers/input/misc/ into drivers/media/rc/
and convert it to use rc-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
