Support for boards based on Techwell TW5864 chip which provides
multichannel video & audio grabbing and encoding (H.264, MJPEG,
ADPCM G.726).
This submission implements only H.264 encoding of all channels at D1
resolution.
Thanks to Mark Thompson <sw@jkqxz.net> for help, and for contribution of
H.264 startcode emulation prevention code.
Signed-off-by: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This commit introduces the support for the Techwell TW686x video
capture IC. This hardware supports a few DMA modes, including
scatter-gather and frame (contiguous).
This commit makes little use of the DMA engine and instead has
a memcpy based implementation. DMA frame and scatter-gather modes
support may be added in the future.
Currently supported chips:
- TW6864 (4 video channels),
- TW6865 (4 video channels, not tested, second generation chip),
- TW6868 (8 video channels but only 4 first channels using
built-in video decoder are supported, not tested),
- TW6869 (8 video channels, second generation chip).
[mchehab@osg.samsung.com: make checkpatch happy by using "unsigned int"
instead of just "unsigned"]
Cc: Krzysztof Halasa <khalasa@piap.pl>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add NetUP Dual Universal CI PCIe board driver.
The board has
- two CI slots
- two I2C adapters
- SPI master bus for accessing flash memory containing
FPGA firmware
No changes required.
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I noticed certain cards are currently under MEDIA_ANALOG_TV_SUPPORT
but it seems they are frame grabbers (with CVBS, Svideo etc. inputs)
rather than TV receivers (with analog TV tuners).
MEDIA_CAMERA_SUPPORT maybe isn't the best name (only "meye" driver seems
to drive a real camera in a laptop) but it at least doesn't select the
TUNERs.
Perhaps the following patch would make sense.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cobalt device is a PCIe card with 4 HDMI inputs (adv7604) and a
connector that can be used to hook up an adv7511 transmitter or an
adv7842 receiver daughterboard.
This device is used within Cisco but is sadly not available outside
of Cisco. Nevertheless it is a very interesting driver that can serve
as an example of how to support HDMI hardware and how to use the popular
adv devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dt3155 code is now in good shape, so move it out of staging into
drivers/media/pci. Mark in MAINTAINERS that I'll do Odd Fixes for this
driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is a new PCIe bridge chip(from SMI) used in DVBSky V3 seris cards, include S950 V3 and S952 V3 cards.
SMI pcie bridge chip is PCIe 1.1 compliant, supports MSI feature.
Main interface blocks:
1>Two DVB transport stream input ports(ts0,ts1).
2>Two I2C master bus(i2c0, i2c1).
3>IR controller.
4>reset pins and other GPIOs.
DVBSky S950 V3 card has a single channel of dvb-s/s2.
1>Frontend: tuner: M88TS2022, demod: M88DS3103
2>PCIe bridge: SMI PCIe
The current driver does not support SMI IR function.
[mchehab@osg.samsung.com: fix Makefile to find m88ts2022.h]
Signed-off-by: Max nibble <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for PT3 PCIe cards.
PT3 has an FPGA PCIe bridge chip, a TC90522 demod chip and
a VA4M6JC2103 tuner module which contains two QM1D1C0042 chips for ISDB-S
and two MxL301RF's for ISDB-T.
It can receive and deliver 4 (2x ISDB-S, 2x ISDB-T) streams simultaneously,
and a kthread is used per stream to poll incoming data,
because PT3 does not have interrupts.
As an antenna input for each delivery system is split in the tuner module
and shared between the corresponding two tuner chips,
LNB/LNA controls that the FPGA chip provides are (naturally) shared as well.
The tuner chips also share the power line in the tuner module,
which is controlled on/off by a GPIO pin of the demod chip.
As with the demod chip and the ISDB-T tuner chip,
the init sequences/register settings for those chips are not disclosed
and stored in a private memory of the FPGA,
PT3 driver executes the init of those chips on behalf of their drivers.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Refactor and clean up the tw68 driver. It's now using the proper
V4L2 core frameworks.
Tested with my Techwell tw6805a and tw6816 grabber boards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the custom motion detection API has been replaced with a
standard API there is no reason anymore to keep it in staging.
So (finally!) move it to drivers/media/pci.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As USB/PCI/MEDIA_SUPPORT dependencies can be tristate, we can't
simply make the bool menu to be dependent on it. Everything below
the menu should also depend on it, otherwise, we risk to allow
building them with 'y', while only 'm' would be supported.
So, add an IF just before everything below, in order to avoid
such risks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
b2c2 is, in fact, 2 drivers: one for PCI and one for USB, plus
a common bus-independent code. Break it accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
