ret is still -1, if during the polling read_byte() returns at once
with I2C_PCA_CON_SI set. So ret > 0 would lead *_waitforcompletion()
to return 0, in spite of the proper behavior.
The routine was rewritten, so that ret has always a proper value,
before returning.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In current i2c core driver, call to pm_runtime_set_active from
i2c_device_pm_resume will unconditionally enable i2c module and
increment child count of the parent. Because of this, in CPU Idle
path, i2c does not idle, preventing Core to enter retention. Also i2c
module will not be suspended upon system suspend as
pm_runtime_set_suspended is not called from i2c_device_pm_suspend.
This issue is fixed by removing pm_runtime_set_active call from resume
path which is not necessary.
This fix has been tested on OMAP4430.
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In case of error during probe() the driver calls free_irq() function
on not yet allocated irq. This patches fixes the call sequence in case of
the error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a driver that uses videobuf-dma-contig is used with the USERPTR
memory access method a kernel oops might happen: a NULL address may be
passed to dma_free_coherent(). This happens when an application calls
REQBUFS and then exits without queuing any buffers. This patch fixes
that bug.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some cards, ir_dev->props and ir_dev->raw are both NULL. These cards are
using built-in IR decoding instead of raw, and can't easily be made to switch
protocols.
So upon reading /sys/class/rc/rc?/protocols on such a card, return 'builtin' as
the supported and enabled protocol. Return -EINVAL on any attempts to change
the protocol. And most important of all, don't crash.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i810 and i830 device drivers may replace their file operations
on an open file descriptor. My previous patch to move the BKL
out of the common DRM code into these drivers only caught the
default file operations, not the ones that actually end up being
used.
Found while trying to come up with a way to kill the BKL for
good in these drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: fix interrupt clearing for mv_xor
missing inline keyword for static function in linux/dmaengine.h
dma/shdma: move dereference below the NULL check
Our list of Toshiba Satellite models that require this workaround
is growing -- so invoke the workaround for the entire product line.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Len Brown <len.brown@intel.com>
The src_base and dst_base fields in apei_exec_context are physical
address, so they should be ioremaped before being used in ERST
MOVE_DATA instruction.
Reported-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 934231de70 fixes an unbalanced
CONFIG_ACPI_PROCFS code block during module initialisation. This
patch fixes similar issue but for the module exit.
Signed-off-by: Luis Henriques <luis.henrix@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pad.c:432: warning: ‘num_cpus’ may be used uninitialized in this function
gcc 4.4.4 was unable to notice that num_cpus is always set.
Re-arrange the code to un-confuse gcc, and also make
it easier for humans to read....
Signed-off-by: Len Brown <len.browns@intel.com>
In ERST debug/test support patch, a dynamic allocated buffer is
used. The may-failed memory allocation should be tried firstly before
free the previous buffer.
APEI resource management memory allocation related error path is fixed
too.
v2:
- Fix error messages for APEI resources management
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
platform_data in hest_parse_ghes() is used for saving the address of entry
information of erst_tab. When the device is failed to be added, platform_data
will be freed by platform_device_put(). But the value saved in platform_data
should not be freed here. If it is done, it will make system panic.
So I think platform_data should save the address of allocated memory
which saves entry information of erst_tab.
This patch fixed it and I confirmed it on x86_64 next-tree.
v2:
Transport the pointer of hest_hdr to platform_data using
platform_device_add_data()
Signed-off-by: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
After we ioremap() a new region, we call __acpi_try_ioremap() to
see whether another thread has already mapped the same region.
This check clobbers "vaddr", so compute the return value of
acpi_pre_map() using the ioremap() result "map->vaddr" instead.
v2:
Modified the unsuitable description of patch.
v3:
Removed unlikely() check and made description simpler.
Signed-off-by: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On Huang Ying's machine:
erst_tab->header_length == sizeof(struct acpi_table_einj)
but Yinghai reported that on his machine,
erst_tab->header_length == sizeof(struct acpi_table_einj) -
sizeof(struct acpi_table_header)
To make erst table size checking code works on all systems, both
testing are treated as PASS.
Same situation applies to einj_tab->header_length, so corresponding
table size checking is changed in similar way too.
v2:
- Treat both table size as valid
Originally-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In max8925_irq_sync_unlock(), irq control bit is set at the same time.
Zero means enabling irq, and one means disabling irq.
The original code is:
irq_chg[0] &= irq_data->enable;
It should be changed to:
irq_chg[0] &= ~irq_data->enable;
Otherwise, irq control bit is mess.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver was originally tested with an additional patch which
made this unneeded but that patch had issuges and got lost on the
way to mainline, causing problems when the errors are reported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: stable@kernel.org
otherwise, these two lines print as one:
ACPI: acpi_idle yielding to intel_idle
ACPI: SSDT 3f5d8741 00203 (v02 PmRef Cpu0Ist 00003000 INTL 20050624)
Signed-off-by: Len Brown <len.brown@intel.com>
intel_idle_cpuidle_devices is a percpu pointer
but was missing __percpu markup.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Disable the Windows Vista (SP1) compatibility for Toshiba P305D.
http://bugzilla.kernel.org/show_bug.cgi?id=14736
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/sysfs.c:154: warning: passing argument 1 of '__check_old_set_param' from incompatible pointer type
include/linux/moduleparam.h:165: note: expected 'int (*)(const char *, struct kernel_param *)' but argument is of type 'int (*)(const char *, const struct kernel_param *)'
Introduced by commit 1c8fce27e2 ("ACPI:
introduce drivers/acpi/sysfs.c") interacting with commit
9bbb9e5a33 ("param: use ops in struct
kernel_param, rather than get and set fns directly").
Use module_param_cb instead of the obsoleted module_param_call to fix a build warning.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Section 4.7.3.1.1 (PM1 Status Registers) of version 4.0 of
the ACPI spec concerning PCIEXP_WAKE_STS points out in
in the final note field in table 4-11 that if this bit is
set to 1 and the system is put into a sleeping state then
the system will not automatically wake.
This bit gets set by hardware to indicate that the system
woke up due to a PCI Express wakeup event, so clear it during
acpi_hw_clear_acpi_status() calls to enable subsequent
resumes to work.
BugLink: http://bugs.launchpad.net/bugs/613381
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
iwl3945's scan_completed calls into the mac80211 stack which triggers a
warn on if there is no scan outstanding.
This can be avoided by not calling scan_completed but abort_scan in
iwl3945_request_scan in the done: branch of the function which is used
as an error out.
The done: branch seems to be an error-out branch, as, for example, if
iwl_is_ready(priv) returns false the done: branch is executed.
NOTE:
I'm not familiar with the driver at all.
I just quickly scanned as a reaction to
https://bugzilla.kernel.org/show_bug.cgi?id=17722
the users of scan_completed in the iwl3945 driver and noted the odd
discrepancy between the comment above this instance and the comment in
mac80211 scan_completed function.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libata depends on scsi_host_template for module reference counting and
sht's should be owned by each low level driver. During libahci split,
the sht was left with libahci.ko leaving the actual low level drivers
not reference counted. This made ahci and ahci_platform always
unloadable even while they're being actively used.
Fix it by defining AHCI_SHT() macro in ahci.h and defining a sht for
each low level ahci driver.
stable: only applicable to 2.6.35.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
tcp: Fix >4GB writes on 64-bit.
net/9p: Mount only matching virtio channels
de2104x: fix ethtool
tproxy: check for transparent flag in ip_route_newports
ipv6: add IPv6 to neighbour table overflow warning
tcp: fix TSO FACK loss marking in tcp_mark_head_lost
3c59x: fix regression from patch "Add ethtool WOL support"
ipv6: add a missing unregister_pernet_subsys call
s390: use free_netdev(netdev) instead of kfree()
sgiseeq: use free_netdev(netdev) instead of kfree()
rionet: use free_netdev(netdev) instead of kfree()
ibm_newemac: use free_netdev(netdev) instead of kfree()
smsc911x: Add MODULE_ALIAS()
net: reset skb queue mapping when rx'ing over tunnel
br2684: fix scheduling while atomic
de2104x: fix TP link detection
de2104x: fix power management
de2104x: disable autonegotiation on broken hardware
net: fix a lockdep splat
e1000e: 82579 do not gate auto config of PHY by hardware during nominal use
...
Commit e40cc4bdfd introduced
a build breakage if CONFIG_SMP is undefined. This commit
fixes the problem.
This fix is only a workaround. For a real fix, cpu_sibling_mask() should
be defined in UP include code, eg in linux/smp.h, and asm/smp.h should not be
included directly. This fix is currently not possible because asm/smp.h defines
cpu_sibling_mask() unconditionally and is included directly from many source
files.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Fix DMA engine pixel offset calculation for 3-planar YUV formats.
On S5PV210 SoCs horizontal offset is applied as number of pixels,
not bytes per line.
[mchehab@redhat.com: CodingStyle cleanup]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At all frame rates except 30fps and 5fps the camera produces very dark
pictures. Auto-exposure is probably disabled by the camera at all frame
rates except 30fps, making them pretty unusable.
Work around the problem by introducing a new RESTRICT_FRAME_RATE quirk
that disables all the frame rates except the default one.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the STREAM_NO_FID quirk. Add a corresponding entry
in the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FBIOGET_VBLANK device ioctl allows unprivileged users to read 16
bytes of uninitialized stack memory, because the "reserved" member of
the fb_vblank struct declared on the stack is not altered or zeroed
before being copied back to the user. This patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The wrong value for the volume control limit, 65335 vs. 65535,
prevents proper cx25840 v4l2_subdevice initialization.
Reported-by: Igor M. liplianin <liplianin@me.by>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Video device was not being released on driver remove.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Output buffer has to be at least the size of input buffer, not the other
way around.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The drivers/media/video/mt9v022.c file, on line 405, tries a "case 0" o a
v4l2_mbus_pixelcode enum which don't have an 0 value element, so I got a compile
warning. That "case" is useless so it can be removed.
Signed-off-by: Ionut Gabriel Popescu <poyo_vl@yahoo.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mx25_camera_irq irq handler may get called after the camera has been
deactivated (from mx2_camera_deactivate). Detect this situation, and bail out.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the end of frame marker does not contain any pixel, it must not be
transferred.
Reported-by: Ivo Jager <ivo.jager@siliconfields.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a nasty memory corruption bug when using userptr I/O.
The function videobuf_pages_to_sg() sets up the scatter-gather list for the
DMA transfer to the userspace pages. The first transfer is setup correctly
(the size is set to PAGE_SIZE - offset), but all other transfers have size
PAGE_SIZE. This is wrong for the last transfer which may be less than PAGE_SIZE.
Most, if not all, drivers will program the boards DMA engine correctly, i.e.
even though the size in the last sg element is wrong, they will do their
own size calculations and make sure the right amount is DMA-ed, and so seemingly
prevent memory corruption.
However, behind the scenes the dynamic DMA mapping support (in lib/swiotlb.c)
may create bounce buffers if the memory pages are not in DMA-able memory.
This happens for example on a 64-bit linux with a board that only supports
32-bit DMA.
These bounce buffers DO use the information in the sg list to determine the
size. So while the DMA engine transfers the correct amount of data, when the
data is 'bounced' back too much is copied, causing buffer overwrites.
The fix is simple: calculate and set the correct size for the last sg list
element.
Signed-off-by: Hans Verkuil <hans.verkuil@tandberg.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers shouldn't sleep while holding a spinlock. A previous workaround
were to release the spinlock before callinc schedule().
This patch uses a different approach: it just waits for the
siano hardware to answer.
Signed-off-by: Richard Zidlicky <rz@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To improve performance on DiB7770-devices enabling the current mirror
is needed.
This patch adds an option to the dib7000p-driver to do that and it
creates a separate device-entry in dib0700-device to use those changes
on hardware which is using the DiB7770.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These keys are found on remote bundled with
Toshiba Qosmio F50-10q.
Found and tested by, Sami R <maesesami@gmail.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The logic in ir_timer_keyup was inverted.
In case that values aren't equal,
the meaning of the time_is_after_eq_jiffies(ir->keyup_jiffies) is that
ir->keyup_jiffies is after the the jiffies or equally that
that jiffies are before the the ir->keyup_jiffies which is
exactly the situation we want to avoid (that the timeout is in the future)
Confusing Eh?
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Anton Blanchard <anton@samba.org>, double IR events on
2.6.36-rc2 and a DViCO FusionHDTV DVB-T Dual Express are happening:
[ 1351.032084] ir_keydown: i2c IR (FusionHDTV): key down event, key 0x0067, scancode 0x0051
[ 1351.281284] ir_keyup: keyup key 0x0067
ie one key down event and one key up event 250ms later.
So, we need to increase the repeat timeout, to avoid this bug to hit.
As we're doing it at core, this fix is not needed anymore at dib0700 driver.
Thanks-to: Anton Blanchard <anton@samba.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Carlos, Prolink Pixelview SBTVD Hybrid is based on
Conexant cx231xx + Fujitsu 86A20S demodulator. However, both shares
the same USB ID. So, we need to use USB bcdDevice, in order to
properly discover what's the board.
We know for sure that bcd 0x100 is used for a dib0700 device, while
bcd 0x4001 is used for a cx23102 device. This patch reserves two ranges,
the first one from 0x0000-0x3f00 for dib0700, and the second from
0x4000-0x4fff for cx231xx devices.
This may need fixes in the future, as we get access to other devices.
Thanks-to: Carlos Americo Domiciano <c_domiciano@yahoo.com.br>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reported in lirc sf.net tracker and on lirc mailing list
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When plugging some webcams on ARM, the system crashes.
This is because we alloc buffer for an urb through usb_buffer_alloc,
the alloced buffer is already in DMA coherent region, so we should
set the flag of this urb to URB_NO_TRANSFER_DMA_MAP, otherwise when
we submit this urb, the hcd core will handle this address as an
non-DMA address and call dma_map_single/sg to map it. On arm
architecture, dma_map_single a DMA coherent address will be catched
by a BUG_ON().
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some time a go our customers wrote me about problem with our TV card
BeholdTV Columbus. It's PCMCIA TV card for notebook.
As I understand v4l has some regression with autodetect address of tuners.
I can set incorrect I2C address and had report about detect tuner. No any TV of course.
When I set correct tuner type and I2C address of the tuners all works well.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code dereferenced "port" before checking it for NULL. I
moved the test down below the check. Also I changed the comparisons a
little so people wouldn't get confused and think "port" and "buf" were
ints instead of pointers. (Probably that's what lead to this issue in
the first place.)
There is only one caller for this function and it passes non-NULL
pointers, so this is essentially a cleanup rather than a bugfix.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We dereference "maskptr" unconditionally at the start of the function
and also inside the call to parse_tlist() towards the end of the
function. This function is called from store_val_any() and it always
passes a non-NULL pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"fw" is always a non-NULL pointer at this point, and anyway
release_firmware() accepts NULL pointers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original code dereferenced ir->raw after freeing it and setting it
to NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we return directly here then we miss out on some mutex_unlock()s
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx88-alsa module has been around since January 2006 and has seen no
significant changes since September 2007. It is stable in operation
and so I believe that the 'experimental' tag is no longer warranted.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PKT_CTRL_CMD_STATUS device ioctl retrieves a pointer to a
pktcdvd_device from the global pkt_devs array. The index into this
array is provided directly by the user and is a signed integer, so the
comparison to ensure that it falls within the bounds of this array will
fail when provided with a negative index.
This can be used to read arbitrary kernel memory or cause a crash due to
an invalid pointer dereference. This can be exploited by users with
permission to open /dev/pktcdvd/control (on many distributions, this is
readable by group "cdrom").
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
[ Rather than add a cast, just make the function take the right type -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Board has no digital connectors
Reported-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hook the GEM vm open/close ops into the generic drm vm open/close so
that the private vma entries are created and destroy appropriately.
Fixes the leak of the drm_vma_entries during the lifetime of the filp.
Reported-by: Matt Mackall <mpm@selenic.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When setting up to transmit, a race exists between the ISR and
i2c_davinci_xfer_msg() trying to load the first byte and adjust counters.
This is mostly visible for transmits > 1 byte long.
The hardware starts sending immediately that MDR is loaded. IMR trickery
doesn't work because if we start sending, finish the first byte and an
XRDY event occurs before we load IMR to unmask it, we never get an
interrupt, and we timeout.
Move the MDR load after DXR,IMR loads to avoid this race without locking.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When the interface is up, using ethtool breaks it because:
a) link is put down but media_timer interval is not shortened to NO_LINK
b) rxtx is stopped but not restarted
Also manual 10baseT-HD (and probably FD too - untested) mode does not work -
the link is forced up, packets are transmitted but nothing is received.
Changing CSR14 value to match documentation (not disabling link check) fixes this.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't make sense to set result to -ETIMEDOUT but return 0 (success)
afterwards. Since there's code in octeon_i2c_start() to handle the
error, it should be called.
Signed-off-by: Bernhard Walle <walle@corscience.de>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* master.kernel.org:/home/rmk/linux-2.6-arm: (28 commits)
ARM: 6411/1: vexpress: set RAM latencies to 1 cycle for PL310 on ct-ca9x4 tile
ARM: 6409/1: davinci: map sram using MT_MEMORY_NONCACHED instead of MT_DEVICE
ARM: 6408/1: omap: Map only available sram memory
ARM: 6407/1: mmu: Setup MT_MEMORY and MT_MEMORY_NONCACHED L1 entries
ARM: pxa: remove pr_<level> uses of KERN_<level>
ARM: pxa168fb: clear enable bit when not active
ARM: pxa: fix cpu_is_pxa*() not expanding to zero when not configured
ARM: pxa168: fix corrected reset vector
ARM: pxa: Use PIO for PI2C communication on Palm27x
ARM: pxa: Fix Vpac270 gpio_power for MMC
ARM: 6401/1: plug a race in the alignment trap handler
ARM: 6406/1: at91sam9g45: fix i2c bus speed
leds: leds-ns2: fix locking
ARM: dove: fix __io() definition to use bus based offset
dmaengine: fix interrupt clearing for mv_xor
ARM: kirkwood: Unbreak PCIe I/O port
ARM: Fix build error when using KCONFIG_CONFIG
ARM: 6383/1: Implement phys_mem_access_prot() to avoid attributes aliasing
ARM: 6400/1: at91: fix arch_gettimeoffset fallout
ARM: 6398/1: add proc info for ARM11MPCore/Cortex-A9 from ARM
...
* git://git.infradead.org/iommu-2.6:
intel-iommu: Use symbolic values instead of magic numbers in Lenovo w/a
intel-iommu: Abort IOMMU setup for igfx if BIOS gave no shadow GTT space
This patch (commit 690a1f2002) added a
new call site for acpi_set_WOL() without checking that the function is
actually suitable to be called via
vortex_set_wol+0xcd/0xe0 [3c59x]
dev_ethtool+0xa5a/0xb70
dev_ioctl+0x2e0/0x4b0
T.961+0x49/0x50
sock_ioctl+0x47/0x290
do_vfs_ioctl+0x7f/0x340
sys_ioctl+0x80/0xa0
system_call_fastpath+0x16/0x1b
i.e. outside of code paths run when the device is not yet enabled or
already disabled. In particular, putting the device into D3hot is a
pretty bad idea when it was already brought up.
Furthermore, all prior callers of the function made sure they're
actually dealing with a PCI device, while the newly added one didn't.
In the same spirit, the .get_wol handler shouldn't indicate support
for WOL for non-PCI devices.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPS driver needs to know the current power consumption of the GMCH
in order to make decisions about when to increase or decrease the CPU
and/or GPU power envelope. So fix up the divisions to save the results
so the numbers are actually correct (contrary to some earlier comments
and code, these functions do not modify the first argument and use it
for the result).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The HW by default has RX coalescing on. For iWARP connections, this
causes a 100ms delay in connection establishement due to the ingress
MPA Start message being stalled in HW. So explicitly turn RX
coalescing off when setting up iWARP connections.
This was causing very bad performance for NP64 gather operations using
Open MPI, due to the way it sets up connections on larger jobs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
f4347553b3 removed the edac polling
mechanism in favor of using a notifier chain for conveying MCE
information to edac. However, the module removal path didn't test
whether the driver had setup the polling function workqueue at all and
the rmmod process was hanging in the kernel at try_to_del_timer_sync()
in the cancel_delayed_work() path, trying to cancel an uninitialized
work struct.
Fix that by adding a balancing check to the workqueue removal path.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing netdev without free_netdev() leads to net, tx leaks.
I might lead to dereferencing freed pointer.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
@@
struct net_device* dev;
@@
-kfree(dev)
+free_netdev(dev)
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables auto loading for the smsc911x ethernet driver.
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
encoder info was not printed properly on boards using the
DFP6 id.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Compex FreedomLine 32 PnP-PCI2 cards have only TP and BNC connectors but the
SROM contains AUI port too. When TP loses link, the driver switches to
non-existing AUI port (which reports that carrier is always present).
Connecting TP back generates LinkPass interrupt but de_media_interrupt() is
broken - it only updates the link state of currently connected media, ignoring
the fact that LinkPass and LinkFail bits of MacStatus register belong to the
TP port only (the chip documentation says that).
This patch changes de_media_interrupt() to switch media to TP when link goes
up (and media type is not locked) and also to update the link state only when
the TP port is used.
Also the NonselPortActive (and also SelPortActive) bits of SIAStatus register
need to be cleared (by writing 1) after reading or they're useless.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least my 21041 cards come out of suspend with bus mastering disabled so
they did not work after resume(no data transferred).
After adding pci_set_master(), the driver oopsed immediately on resume -
because de_clean_rings() is called on suspend but de_init_rings() call
was missing in resume.
Also disable link (reset SIA) before sleep (de4x5 does this too).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If not all clocks have been defined in platform data, the driver will
cause a null pointer dereference when it is removed. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the commit f522886e20 a merge conflict
in the sdhci-s3c driver been fixed. However the fix used incorrect
spinlock operation - it caused a race with sdhci interrupt service. The
correct way to solve it is to use spin_lock_irqsave/irqrestore() calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
At least on older 21041-AA chips (mine is rev. 11), TP duplex autonegotiation
causes the card not to work at all (link is up but no packets are transmitted).
de4x5 disables autonegotiation completely. But it seems to work on newer
(21041-PA rev. 21) so disable it only on rev<20 chips.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
x86/hwmon: pkgtemp has no dependency on PCI
MAINTAINERS: Update hwmon entry
x86/hwmon: register alternate sibling upon CPU removal
x86/hwmon: fix initialization of pkgtemp
x86/hwmon: fix initialization of coretemp
x86/hwmon: don't leak device attribute file from pkgtemp_probe() and pkgtemp_remove()
x86/hwmon: avoid deadlock on CPU removal in pkgtemp
x86/hwmon: fix module init for hotplug-but-no-device-found case
hwmon: (lis3) Fix Oops with NULL platform data
While fb isn't active, we should clear CFG_GRA_ENA bit. The existing code
can't clear this bit.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
When the Lenovo Ideapad S10-3 is booted with HT enabled,
it hits a boot hang in the intel_idle driver.
This occurs when entering ATM-C4 for the first time,
unless BM_STS is first cleared.
acpi_idle doesn't see this because it first checks
and clears BM_STS, but it would hit the same hang
if that check were disabled.
http://bugs.meego.com/show_bug.cgi?id=7093https://bugs.launchpad.net/ubuntu/+source/linux/+bug/634702
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: update Kconfig help text for CONFIG_USB_SUSPEND
usb: musb: gadget: restart request on clearing endpoint halt
usb: musb: host: Issue a memory barrier before starting DMA
usb: musb: gadget: fix dma length in txstate
usb: musb: gadget: complete request only if data is transfered over
usb: musb: gadget: fix DMA length for OUT transfer
usb: musb: gadget: enable autoclear for OUT transfer in both DMA 0 and DMA 1
usb: musb: gadget: fix bulk IN infinit hangs in double buffer case
usb: musb: gadget: fix kernel panic if using out ep with FIFO_TXRX style
USB: fix bug in initialization of interface minor numbers
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vgaarb: trivial fix
drm: radeon cleanup fixes...
drm: fix trivial coding errors
drm: ttm sparse fixes.
drm/nouveau: fix panels using straps-based mode detection
drm/ttm: Clear the ghost cpu_writers flag on ttm_buffer_object_transfer.
drm/radeon: don't allow device to be opened if powered down
Commit 2a6b69765a (ACPI: Store NVS
state even when entering suspend to RAM) changed the ACPI suspend
to RAM code so that the NVS memory area is always unconditionally
saved during suspend and restored during resume, since some systems
evidently need that for the suspend-resume to work on them. However,
it turned out that this change broke suspend-resume on a few systems,
so commit 72ad5d77fb (ACPI / Sleep:
Allow the NVS saving to be skipped during suspend to RAM) introduced
the acpi_sleep=nonvs command line switch to allow their users to
work around this issue. To keep track of the systems that require
this workaround and to make the life of their users slightly easier
blacklist them in acpisleep_dmi_table[].
https://bugzilla.kernel.org/show_bug.cgi?id=16396
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Other than coretemp, from which this code was apparently derived, there
is no PCI specific code in this driver.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Just like pkgtemp registers another core of the same package when one
gets removed, coretemp should register another hyperthread (if
available) in that situation.
As pointed out in the patch fixing the respective code in pkgtemp, the
list protectng mutex must be dropped before calling
coretemp_device_add(), and due to the restructured loop (including an
explicit return) the "safe" variant of the list iterator isn't needed
anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Feature availability should also be checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Using cpuid_eax() to determine feature availability on other than
the current CPU is invalid. And feature availability should also be
checked in the hotplug code path.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp_device_remove(), holding the list protecting mutex, calls
pkgtemp_device_add(), which itself wants to acquire the same mutex.
Holding the mutex over the entire loop body in pkgtemp_device_remove()
isn't really necessary, as long as the loop gets exited after
processing the matched CPU.
Once exiting the loop after removing an eventual match, there's no
need for using the "safe" list iterator anymore.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
In commit 0dca94baea the call to
platform_driver_unregister() was made conditional upon !HOTPLUG_CPU,
but the return value from coretemp_init() was left to indicate an
error. This isn't correct, as the negative return value indicates to
the module loader that initialization failed, which isn't intended
here and results in dangling pointers.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The recent addition of threaded irq handler causes a NULL dereference
when used with hp_accel driver, which has NULL pdata.
Acked-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch (as1429) updates the Kconfig help text for
CONFIG_USB_SUSPEND. The power/level file is now deprecated; we should
tell people to use power/control instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 46034dca51 (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the issue which was observed while transfering
a large file ( > 20MB) over USB (OMAP MUSB controller acts as USB host)
to an attached USB thumb drive.
It was found that CDB field of CBW packet was set to 0x0. This was
due to missing a barrier before DMA engine starts transfer.
This buffer is allocated using dma_alloc_coherent which gives
non-cacheble but bufferable memory and hence needed a write
memory barrier to flush the write buffer.
More info on this thread is here:
http://www.spinics.net/lists/linux-omap/msg33987.html
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space
of request buffer, so fix it.
Also set max_len of cppi dma channel as max size of
int type, so make musb dma handling happier.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Complete the current request only if the data transfer is over.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space of request buffer,
so fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one bugs of OUT transfer in double buffer case:
-the current code only enable autoclear for dma mode 1, and not
for dma mode 0
Without this patch, test #5 of usbtest can't be passed if we
configure musb as g_zero and use fifo mode 3 to enable double
buffer mode.
With this patch and the following patch(fix dma length),
on my beagle B5, test#5(queued bulk out) may go beyond
18Mbyte/s(seems dma mode 0 is quicker in double buffer case)
if musb is configured as g_zero and fifo mode 3 is taken, follows
the test command:
#./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8 [1]
Also I have tested this patch can't make g_ether broken.
[1],source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one infinite hang of bulk IN transfer in double buffer
case, the hang can be observed easily by test #6 of usbtest if musb is
configured as g_zero and fifo mode 3 is taken to enable double fifo.
In fact, the patch only removes the check for non-empty fifo before
loading data from new request into fifo since the check is not correct:
-in double buffer case, fifo may accommodate more than one packet,
even though it has contained one packet already and is non-empty
-since last DMA is completed before calling musb_g_tx, it is sure
that fifo may accommodate at least one packet
Without applying the patch, new requst enqueued from .complte may not
have a chance to be loaded into fifo, then will never be completed and
cause infinite hangs.
With the patch, on my beagle B5, test#6(queued bulk in) can be passed and
test result may go beyond 33Mbyte/s if musb is configured as g_zero and
fifo mode 3 is taken, follows the test command:
#testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8 [1]
[1],
-source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Philip J. Turmel <philip@turmel.org>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Matthias Bayer <jackdachef@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to support multiple ST platform devices, a new symbol
'st_get_plat_device' earlier needed to be exported by the arch/XX/brd-XX.c
file which intends to add the ST platform device.
On removing this dependency, now inside ST driver maintain the array of
ST platform devices that would be registered.
As of now let id=0, as and when we end up having such platforms
where mutliple ST devices can exist, id would come from
protocol drivers (BT, FM and GPS) as to on which platform device
they want to register to.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct function being needlessly visible outside compilation unit
when the only users are internal.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix string interpreted as trigraph and typo.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Correct function storage class, and correct assignment type.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Correct allocation flags type and function prototype for ANSI C compliance.
[airlied: whitespace fixed]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When using simultaneously the two DMA channels on a same engine, some
transfers are never completed. For example, an endless lock can occur
while writing heavily on a RAID5 array (with async-tx offload support
enabled).
Note that this issue can also be reproduced by using the DMA test
client.
On a same engine, the interrupt cause register is shared between two
DMA channels. This patch make sure that the cause bit is only cleared
for the requested channel.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Tested-by: Luc Saillard <luc@saillard.org>
Acked-by: saeed bishara <saeed.bishara@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Change the code so that it will use the correct size for keymap entries.
Do it in a way that makes it harder to screw it up in the future.
Reported-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In the event that the external chipset doesn't implement the
GET_SUPPORTED_ENHANCEMENTS commands, gracefully treat it as having no
enhancments rather than bailing.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We weren't unlinking the freed connector from the drm lists, and so
hit some use-after-free if we failed to initialise the connector.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A minor typo caused a single fence register to be incorrectly
programmed, resulting in occassional tiling corruption.
Reported-and-tested-by: Hans de Bruin <bruinjm@xs4all.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18962
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
For non-managed versions of 82579, set the bit that prevents the hardware
from automatically configuring the PHY after resets only when the driver
performs a reset, clear the bit after resets. This is so the hardware can
configure the PHY automatically when the part is reset in a manner that is
not controlled by the driver (e.g. in a virtual environment via PCI FLR)
otherwise the PHY will be mis-configured causing issues such as failing to
link at 1000Mbps.
For managed versions of 82579, keep the previous behavior since the
manageability firmware will handle the PHY configuration.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subject workaround was causing CRC errors due to writing the wrong
register with updates of the RCTL register. It was also found that the
workaround function which modifies the RCTL register was being called in
the middle of a read-modify-write operation of the RCTL register, so the
function call has been moved appropriately. Lastly, jumbo frames must not
be allowed when CRC stripping is disabled by a module parameter because the
workaround requires the CRC be stripped.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 82579, there is a hardware bug that can cause received packets to not
get transferred from the PHY to the MAC due to K1 (a power saving feature
of the PHY-MAC interconnect similar to ASPM L1). Since the MAC controls
the accounting of missed packets, these will go unnoticed. Workaround the
issue by setting the K1 beacon duration according to the link speed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two recent patches to cleanup the reset[1] and initial PHY configuration[2]
code paths for ICH/PCH devices inadvertently left out a 10msec delay and
device ID check respectively which are necessary for the 82566DC (device id
0x104b) to be configured properly, otherwise it will not get link.
[1] commit e98cac447c
[2] commit 3f0c16e844
CC: stable@kernel.org
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the hardware is prevented from performing automatic PHY configuration
(the driver does it instead), the OEM_WRITE_ENABLE bit in the EXTCNF_CTRL
register will not get cleared preventing the SMBus address and the LED
configuration to be written to the PHY registers. On 82579, do not check
the OEM_WRITE_ENABLE bit.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
