Express available frequencies in mHZ in order to support even
rational ODRs. This patch is need to fix an Android CTS failure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since st_lsm6dsx i2c master controller relies on accel device as trigger
and slave devices can run at different ODRs we must select an accel_odr >=
slave_odr. Report real accel ODR in st_lsm6dsx_check_odr() in order to
properly set sensor frequency in st_lsm6dsx_write_raw and avoid to
report unsupported frequency
Fixes: 6ffb55e500 ("iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce odr_len in st_lsm6dsx_odr_table_entry data structure in order
to explicitly define odr table size and support devices with different
odr table map
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSRX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsrx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS0 6-axis (acc + gyro) Mems sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix typos in gyro gain definitions for LSM9DS1 sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On LSM6DSO/LSM6DSR/LSM6DSOX/ASM330LHH and ISH330DHCX
devices it is possible to trim the hardware timestamp
resolution through the FREQ_FINE[7:0] bits of the
INTERNAL_FREQ_FINE register, which contains the difference
in percentage of the effective ODR (and timestamp rate)
with respect to the typical value.
The formula for calculating the effective ODR reported
in the application notes has been linearized to the first
order to simplify the calculation (pls. see note on source
code).
This change may be useful in the outcome of CTS
tests regarding the SingleSensorTests and the
SensorTest#testSensorTimeStamps for high ODRs
Signed-off-by: Mario Tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable drdy mask if available in order to mark invalid samples during
sensor bootstrap phase
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing wake-up register info for LSM6DSO/LSM6DSOX sensor
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add missing kernel doc for st_lsm6dsx_hw data structure
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the possibility to enable/disable wakeup source through
st_sensors_platform_data and not only through device tree
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix following checkpatch warnings:
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_read_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
CHECK: Alignment should match open parenthesis
+static int st_lsm6dsx_write_event_config(struct iio_dev *iio_dev,
+ const struct iio_chan_spec *chan,
WARNING: line over 80 characters
+ if (dev->of_node && of_property_read_bool(dev->of_node, "wakeup-source"))
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Always grub conf mutex in st_lsm6dsx_write_event_config since it can run
concurrently with FIFO configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_update_bits_locked in st_lsm6dsx_write_event and
st_lsm6dsx_event_setup routines since they can run concurrently with
sensor hub configuration
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check if enable_reg of event_settings data structure is defined before
writing on it
Fixes: b5969abfa8 ("iio: imu: st_lsm6dsx: add motion events")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move bdu, boot and reset register definitions in hw_settings register
map since not all supported sensors (e.g lsm9ds1) rely on the same
definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move active low and open drain register definitions in hw_settings
register map since not all supported sensors (e.g lsm9ds1) rely on the
same definitions
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Group irq related definition in irq_config structure in
st_lsm6dsx_settings. This is a preliminary patch to move
OpenDrain/Active low registers in st_lsm6dsx_settings.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check read_fifo pointer before using it since we can't assume it
is always set adding new sensors. This patch fixes the following crash:
irq 277: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc5-00322-g792b824-dirty #7
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[<c0112750>] (unwind_backtrace) from [<c010d018>] (show_stack+0x10/0x14)
[<c010d018>] (show_stack) from [<c0c2bfc8>] (dump_stack+0xd8/0x10c)
[<c0c2bfc8>] (dump_stack) from [<c01923fc>] (__report_bad_irq+0x24/0xc0)
[<c01923fc>] (__report_bad_irq) from [<c0192820>] (note_interrupt+0x27c/0x2dc)
[<c0192820>] (note_interrupt) from [<c018f174>] (handle_irq_event_percpu+0x54/0x7c)
[<c018f174>] (handle_irq_event_percpu) from [<c018f1d4>] (handle_irq_event+0x38/0x5c)
[<c018f1d4>] (handle_irq_event) from [<c0193664>] (handle_level_irq+0xc8/0x154)
[<c0193664>] (handle_level_irq) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c053c348>] (mxc_gpio_irq_handler+0xc4/0xf8)
[<c053c348>] (mxc_gpio_irq_handler) from [<c053c3e0>] (mx3_gpio_irq_handler+0x64/0xb8)
[<c053c3e0>] (mx3_gpio_irq_handler) from [<c018df58>] (generic_handle_irq+0x20/0x34)
[<c018df58>] (generic_handle_irq) from [<c018e550>] (__handle_domain_irq+0x64/0xe0)
[<c018e550>] (__handle_domain_irq) from [<c0529610>] (gic_handle_irq+0x4c/0xa0)
[<c0529610>] (gic_handle_irq) from [<c0101a70>] (__irq_svc+0x70/0x98)
Exception stack(0xc1301f10 to 0xc1301f58
1f00: 00000001 00000006 00000000 c130c340
1f20: c1300000 c1308928 00000001 c1308960 00000000 c12b9db0 c1308908 00000000
1f40: 00000000 c1301f60 c0182010 c0109508 20000013 ffffffff
[<c0101a70>] (__irq_svc) from [<c0109508>] (arch_cpu_idle+0x20/0x3c)
[<c0109508>] (arch_cpu_idle) from [<c015ed70>] (do_idle+0x1bc/0x2bc)
[<c015ed70>] (do_idle) from [<c015f204>] (cpu_startup_entry+0x18/0x1c)
[<c015f204>] (cpu_startup_entry) from [<c1200e68>] (start_kernel+0x440/0x504)
[<c1200e68>] (start_kernel) from [<00000000>] (0x0)
handlers:
[<62052c0d>] st_lsm6dsx_handler_irq threaded
[<f2004b92>] st_lsm6dsx_handler_thread
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Tested-by: Bobby Jones <rjones@gateworks.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event since
it can run concurrently with sensor hub configuration. Move event
related code in st_lsm6dsx_report_motion_event
Fixes: 1aabad1fb5 ("iio: imu: st_lsm6dsx: add motion report function and call from interrupt")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller available in st_lsm6dsx series performs i2c slave
configuration using accel clock as trigger.
st_lsm6dsx_shub_wait_complete routine is used to wait the controller has
carried out the requested configuration. However if the accel sensor is not
enabled we should not use its configured odr to estimate a proper timeout
Fixes: c91c1c844e ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Report iio motion events to iio subsystem and filter motion events.
Wakeup will still be on all channels as it's not possible to do the filtering
in hw.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The interrupt source can come from multiple sources,
fifo and wake interrupts.
Enter interrupt thread to check which interrupt that has fired.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This add ways for the SoC to wake from accelerometer wake events.
In the suspend function we skip disabling the sensor if wakeup-source
and events are activated.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add event channels that controls the creation of motion events.
Tested on ISM330DLC
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This prepares the interrupt to be used for other stuff than
fifo reading + event readings.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable clear on read feature for latched interrupts. This bit allows
immediately clearing the latched interrupts of an event detection upon
the read of the corresponding status register.
It must be set to 1 together with LIR.
This feature is available just on LSM6DS0/LSM6DSR/ASM330LHH
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable Latched interrupt by default for sensor events
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not allow configuring null sensor gain since it will force to 0
device outputs
Fixes: c8d4066c7246 ("iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rely on IIO_G_TO_M_S_2 macro for LSM9DS1 accelerometer gain definitions
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Get rid of invalid sensitivity value for LSM9DS1 gyro sensor
Fixes: 52f4b1f196 ("iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the latest version of datasheet the mask
for number of unread sensor data in FIFO_STATUS registers
has been extended to 10 bits
The devices involved are:
- LSM6DSO
- LSM6DSOX
- ASM330LHH
- LSM6DSR
- ISM330DHCX
Signed-off-by: mario tesi <mario.tesi@st.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LSM9DS1's accelerometer / gyroscope unit and it's magnetometer (separately
supported in iio/magnetometer/st_magn*) are located on a separate i2c addresses
on the bus.
For the datasheet, see https://www.st.com/resource/en/datasheet/lsm9ds1.pdf
Treat it just like the LSM6* devices and, despite it's name, hook it up
to the st_lsm6dsx driver, using it's basic functionality.
accelerometer and gyroscope are not independently clocked. It runs at the gyro
frequencies if both are enabled, see chapter 7.12 of the datasheet.
We could have handled this as a single IIO device but we have split
it up to be more consistent with the other more flexible devices.
Despite supporting and testing the LSM9DS1, we call the gyro channels
iio_chan_spec struct "st_lsm6ds0_gyro_channels" because the register
description is equal. This suggests that supporting LSM6DS0 should be
trivial to do.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move some register definitions to the per-device array of struct
st_lsm6dsx_sensor_settings in order to simplify adding new sensor
devices to the driver.
Also, remove completely unused register definitions.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce update_fifo routine pointer in st_lsm6dsx_fifo_ops data
structure since we will need a different update FIFO configuration
callback adding support for lsm6ds0/lsm9ds1 imu device
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
in_accel_x_scale, in_accel_y_scale and in_accel_z_scale are always
the same. The scale is still defined to be in "info_mask_separate".
Userspace (iio-sensor-proxy and others) is not used to that and only
looks for "in_accel_scale" for the scaling factor to apply.
Change IIO_CHAN_INFO_SCALE from being separate in all channel to be
shared by type.
This removes in_accel_x_scale, in_accel_y_scale and in_accel_z_scale and
makes available in_accel_scale.
This is an ABI change, but hopefully in the 'no one will notice'
category. The cleanup in interface is worth the small risk that
there is a custom script out there somewhere that this will break.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM ISM330DHCX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move IIO channel definitions in st_lsm6dsx_sensor_settings in order to
support sensors with different channels maps.
This is a preliminary patch to add support for LSM9DS1 sensor to
st_lsm6dsx driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove output register definition and inline register value since
they are used only for iio channel definition. This is a preliminary
patch to add support for LSM9DS1 sensor to st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move fs_table in st_lsm6dsx_sensor_settings in order to support
sensors with different gain maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move sensor odr table in st_lsm6dsx_sensor_settings in order to support
sensors with different odr maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No need for using reverse logic in the irq return,
fix this by flip things around.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For today the st_lsm6dsx driver support LSM6DSO and LSM6DSR sensor only in
spi and i2c mode.
The LSM6DSO and LSM6DSR are also i3c capable so let's give i3c support to
them.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS3TR-C 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6ds3tr-c.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAl0VHIkRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FojyxhAAgrLRy2wlHjQCAh0S6J22LKs02uPX1qvY
nm1aI/av2DGcMCV2NF6J1sW2Mocvtt5a79/1f/wRqDzOHBrTpFr0Q0Ngwijv9bzc
fv6NwfHlWolmXynKx8wK4b6Sa3KVCkltojEVpEVbhkuMkafSQ+pQzYF1Uf7enOrX
j3Gq6NYaCks4YtFZsBphgzo3DC0mh7CfunlPiOdVcgcg4Pj/KZY9QCX86fJx972x
YI3BRFHnDSMDOxOTjeqeKvMiqU2zLPlqLSEOCUw2XCrh6HI9qFiU+LVsYx6SP0tx
aJ2q+qYc9raOTANHk7O2JZYWv/52JXvtKcFSLiuQdABjaAI20xEr1QAZYVYUiXmg
dFH6lBsWvQyAy5F/SyZ5tavZvTfGsNDB5LhlpEggeO2W6cIIL4CLfHimB2EcxFSH
utqEA72HQZosEUKut1jbmG6iYMiRnHS72pLOqkJ6HC/2/pZfoEWlEH9x/S3xbBsW
918ISs9852VwjebQwck96+Dh0LwiKOl8Aii5ONzfNObJB6/JbULPoKKArsMdENQA
mqDXLOMz6GspY3JgiVDCXAwg2x2Ht/ictR6svRJtOTLiBU2Iybpm/HRkPePhoePF
HLw8fhwE+mOSWr22KhzjUJBHEAkoejo/14XOgKSTkO9V6amLlOWRDV3uK2PksmdI
7DQyYhX9Tos=
=a3vh
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO device support, features, cleanups and minor fixes for 5.3.
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
* tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits)
iio: iio-utils: Fix possible incorrect mask calculation
iio: frequency: adf4371: Add support for output stage mute
dt-bindings: iio: frequency: Add ADF4372 PLL documentation
iio: frequency: adf4371: Add support for ADF4372 PLL
dt-bindings: iio: adc: Add buffered input property
Convert AD7124 bindings documentation to YAML format.
iio: adc: ad7124: Shift to dynamic allocation for channel configuration
iio: adc: ad7124: Add buffered input support
iio: adc: ad7124: Remove input number limitation
MAINTAINERS: add ADIS IMU driver library entry
iio: adis162xx: fix low-power docs & reports
counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR
iio: core: no need to check return value of debugfs_create functions
docs: iio: convert to ReST
iio: adc: stm32-adc: add missing vdda-supply
dt-bindings: iio: adc: stm32: add missing vdda supply
iio: adc: stm32-dfsdm: add comment for 16 bits record
iio: adc: stm32-dfsdm: add fast mode support
iio: adc: stm32-dfsdm: manage data resolution in trigger mode
iio: adc: stm32-dfsdm: fix data type
...
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
-----BEGIN PGP SIGNATURE-----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=2i3G
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 5.2 cycle.
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
* tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
Introduce sensor name in st_lsm6dsx_sensor_settings table. This is
a preliminary patch to add I3C support to st_lsm6dsx since i3c_device_id
data structure does not contain a name field
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly suspend/resume i2c slaves connected to st_lsm6dsx master
controller if the CPU goes in suspended state
Fixes: c91c1c844e ("imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
