Remove owner argument, as it is obsolete and unused.
This also saves the overhead of calculating its value in data-path.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: kernel-team@fb.com
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add byte_enable for ocp_read_word() to replace reading 4
bytes data with reading the desired 2 bytes data.
This is used to avoid the issue which is described in
commit b4d99def09 ("r8152: remove sram_read"). The
original method always reads 4 bytes data, and it may
have problem when reading the PHY registers.
The new method is supported since RTL8153B, but it
doesn't influence the previous chips. The bits of the
byte_enable for the previous chips are the reserved
bits, and the hw would ignore them.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The settings of the new chip are the same with RTL8152, except that
its product ID is 0x8050.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where, in the case of a device reset,
the polling routine will never complete, causing napi_disable
to sleep indefinitely when attempting to close the device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a kernel panic resulting from data access of a NULL
pointer during device close. The pending_scrq routine is
meant to determine whether there is a valid sub-CRQ message
awaiting processing. When the device is closing, however,
there is a possibility that NULL messages can be processed
because pending_scrq will always return 1 even if there
no valid message in the queue.
It's not clear what this closing state check was originally
meant to accomplish, so just remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixup a typo so that the entire SCRQ buffer is cleaned.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netif_tx_disable to guarantee that TX queues are disabled
when __ibmvnic_close is called by the device reset routine.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX buffer pools are disabled while awaiting a device
reset if firmware indicates that the resource is closed.
This patch fixes a bug where pools were not being
subsequently enabled after the device reset, causing
the device to become inoperable.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As much as we'd like to play well with others, we really aren't
handling the checksums on non-IP protocol packets very well. This
is easily seen when trying to do TCP over ipv6 - the checksums are
garbage.
Here we restrict the checksum feature flag to just IP traffic so
that we aren't given work we can't yet do.
Orabug: 26175391, 26259755
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove useless variable rxd_index and code related.
Addresses-Coverity-ID: 1397691
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the remaining Global IP and IEEE Priority and Core
Tag Type registers and give them a clear 16-bit register representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Stats Operation and Counter registers and
give them a clear 16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Monitor Control Register macros
(which became the Global Monitor & MGMT Control Register with 88E6390)
and give a clear 16-bit registers representation.
Use __bf_shf to get the shift value at compile time instead of adding
new defined macros for it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Control and Control 2 registers macros
and give a clear 16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global VTU registers macros and give a clear
16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global ATU Registers macros and give clear
16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Switch MAC Address Register macros and
give clear 16-bit register representation.
At the same time, move mv88e6xxx_g1_set_switch_mac in global1.c, where
it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Status Register macros and give clear
16-bit register representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may sleep under a spin lock, and the function call path is:
i40e_ndo_set_vf_port_vlan (acquire the lock by spin_lock_bh)
i40e_vsi_remove_pvid
i40e_vlan_stripping_disable
i40e_aq_update_vsi_params
i40e_asq_send_command
mutex_lock --> may sleep
To fixed it, the spin lock is released before "i40e_vsi_remove_pvid", and
the lock is acquired again after this function.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we hit this error path we end up returning ERR_PTR(0) which is NULL.
The caller is not expecting that so it results in a NULL dereference.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The p_l2_info->pp_qid_usage[] array has "p_l2_info->queues" elements so
the > here should be a >= or we write beyond the end of the array.
Fixes: bbe3f233ec ("qed: Assign a unique per-queue index to queue-cid")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for access cable info via ethtool.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCIA register is used to access the SFP+ and QSFP connector's
EPROM. It will be used to query the cable info.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvlan dev should propagate the return value of mac address change for
lower device in the passthru mode, instead of always return 0.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call pci_set_drvdata immediately after calling register_netdev,
which leaves a window where tasks writing to the sriov_numvfs sysfs
attribute can sneak in and crash the kernel. register_netdev cleans
up after itself so placing pci_set_drvdata immediately before it
should preserve the intent of commit 0fb6a55cc3 ("ixgbe: fix crash
on rmmod after probe fail").
Fixes: 0fb6a55cc3 ("ixgbe: fix crash on rmmod after probe fail")
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
cppcheck warns that the format string is incorrect in the function
ixgbe_get_strings(). Since the value cannot be negative, change the
variable to unsigned which matches the format specifier.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_write_qde() was ignoring the qde parameter which resulted
in PFQDE.HIDE_VLAN not being set for X550.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbevf version number.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update ixgbe version number.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an ixgbe_ptp_tx_hang() function similar to the already existing
ixgbe_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver uses a state bit lock to avoid handling more than one Tx
timestamp request at once. This is required because hardware is limited
to a single set of registers for Tx timestamps.
The state bit lock is not properly cleaned up during
ixgbe_xmit_frame_ring() if the transmit fails such as due to DMA or TSO
failure. In some hardware this results in blocking timestamps until the
service task times out. In other hardware this results in a permanent
lock of the timestamp bit because we never receive an interrupt
indicating the timestamp occurred, since indeed the packet was never
transmitted.
Fix this by checking for DMA and TSO errors in ixgbe_xmit_frame_ring() and
properly cleaning up after ourselves when these occur.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware related to the ixgbe driver is limited to handling a single Tx
timestamp request at a time. Thus, the driver ignores requests for Tx
timestamp while waiting for the current request to finish. It uses
a state bit lock which enforces that only one timestamp request is
honored at a time.
Unfortunately this suffers from a simple race condition. The bit lock is
not cleared until after skb_tstamp_tx() is called notifying applications
of a new Tx timestamp. Even a well behaved application sending only one
packet at a time and waiting for a response can wake up and send a new
packet before the bit lock is cleared. This results in needlessly
dropping some Tx timestamp requests.
We can fix this by unlocking the state bit as soon as we read the
Timestamp register, as this is the first point at which it is safe to
unlock.
To avoid issues with the skb pointer, we'll use a copy of the pointer
and set the global variable in the driver structure to NULL first. This
ensures that the next timestamp request does not modify our local copy
of the skb pointer.
This ensures that well behaved applications do not accidentally race
with the unlock bit. Obviously an application which sends multiple Tx
timestamp requests at once will still only timestamp one packet at
a time. Unfortunately there is nothing we can do about this.
Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for supporting multiple CPU ports, remove
dst->master_netdev and ds->master_netdev and replace them with only one
instance of the common object we have for a port: struct
dsa_port::netdev. ds->master_netdev is currently write only and would be
helpful in the case where we have two switches, both with CPU ports, and
also connected within each other, which the multi-CPU port patch series
would address.
While at it, introduce a helper function used in net/dsa/slave.c to
immediately get a reference on the master network device called
dsa_master_netdev().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SF bit is not cleared in PL_INT_CAUSE, subsequent non-data
interrupts are not raised. Enable SF bit in Global Interrupt
Mask and handle it as non-fatal and hence eventually clear it.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary setting of flag IFF_BROADCAST, since ether_setup
already does this.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when dumping a context data only word number '1' is read for the
entire context.
Fixes: c965db4446 ("qed: Add support for debug data collection")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new Sierra Wireless EM7305 device ID used in a Toshiba laptop,
and two Longcheer device IDs entries used by Telewell TW-3G HSPA+
branded modems.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Reported-by: Teemu Likonen <tlikonen@iki.fi>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90eff9096c ("net: phy: Allow splitting MDIO
bus/device support from PHYs") we could create a configuration where
MDIO_DEVICE=y and PHYLIB=m which leads to the following undefined
references:
drivers/built-in.o: In function `thunder_mdiobus_pci_remove':
>> mdio-thunder.c:(.text+0x2a212f): undefined reference to
>> `mdiobus_unregister'
>> mdio-thunder.c:(.text+0x2a2138): undefined reference to
>> `mdiobus_free'
drivers/built-in.o: In function `thunder_mdiobus_pci_probe':
mdio-thunder.c:(.text+0x2a22e7): undefined reference to
`devm_mdiobus_alloc_size'
mdio-thunder.c:(.text+0x2a236f): undefined reference to
`of_mdiobus_register'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 90eff9096c ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's already added by pr_fmt so remove the explicit use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO reset GPIO is really a classical optional GPIO property case,
so devm_gpiod_get_optional() should have been used, not devm_gpiod_get().
Doing this saves several LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c5e7a2c05 ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact, still
burdening the kernel with now apparently useless loops -- get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a driver reset due to a failover of the backing
server on the vios, doing the netdev_notify_peers() can cause
network traffic to stall or halt. Remove the netdev notify call
for failover resets.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IBM vNIC protocol provides support for the user to initiate
a failover from the client LPAR in case the current backing infrastructure
is deemed inadequate or in an error state.
Support for two H_VIOCTL sub-commands for vNIC devices are required
to implement this function. These commands are H_GET_SESSION_TOKEN
and H_SESSION_ERR_DETECTED.
"[H_GET_SESSION_TOKEN] is used to obtain a session token from a VNIC client
adapter. This token is opaque to the caller and is intended to be used in
tandem with the SESSION_ERROR_DETECTED vioctl subfunction."
"[H_SESSION_ERR_DETECTED] is used to report that the currently active
backing device for a VNIC client adapter is behaving poorly, and that
the hypervisor should attempt to fail over to a different backing device,
if one is available."
To provide tools access to this functionality the vNIC driver creates a
sysfs file that, when written to, will send a request to pHyp to failover
to a different backing device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
