Add a struct device * member to the private driver data and use
it to print messages using dev_* functions rather than pr_*.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
RX DMA tail data handling doesn't work correctly in many cases with current
implementation. It happens because SPI core was setup to generates both RX
and RX TAIL events. And RX TAIL event does not work correctly.
This can be easily verified by sending SPI transaction with size modulus
WML(32 in our case) not equal 0.
Also removing change introduced in f6ee9b582d
since this change only fix usecases with transfer size from 33 to 128 bytes
and doesn't fix 129 bytes and bigger.
This is output from transaction with len 138 bytes in loopback mode at 10Mhz:
TX0000: a3 97 a2 55 53 be f1 fc f9 79 6b 52 14 13 e9 e2
TX0010: 2d 51 8e 1f 56 08 57 27 a7 05 d4 d0 52 82 77 75
TX0020: 1b 99 4a ed 58 3d 6a 52 36 d5 24 4a 68 8e ad 95
TX0030: 5f 3c 35 b5 c4 8c dd 6c 11 32 3d e2 b4 b4 59 cf
TX0040: ce 23 3d 27 df a7 f9 96 fc 1e e0 66 2c 0e 7b 8c
TX0050: ca 30 42 8f bc 9f 7b ce d1 b8 b1 87 ec 8a d6 bb
TX0060: 2e 15 63 0e 3c dc a4 3a 7a 06 20 a7 93 1b 34 dd
TX0070: 4c f5 ec 88 96 68 d6 68 a0 09 6f 8e 93 47 c9 41
TX0080: db ac cf 97 89 f3 51 05 79 71
RX0000: a3 97 a2 55 53 be f1 fc f9 79 6b 52 14 13 e9 e2
RX0010: 2d 51 8e 1f 56 08 57 27 a7 05 d4 d0 52 82 77 75
RX0020: 1b 99 4a ed 58 3d 6a 52 36 d5 24 4a 68 8e ad 95
RX0030: 5f 3c 35 00 00 b5 00 00 00 c4 00 00 8c 00 00 dd
RX0040: 6c 11 32 3d e2 b4 b4 59 cf ce 23 3d 27 df a7 f9
RX0050: 96 fc 1e e0 66 2c 0e 7b 8c ca 30 42 8f 1f 1f bc
RX0060: 9f 7b ce d1 b8 b1 87 ec 8a d6 bb 2e 15 63 0e ed
RX0070: ed 3c 58 58 58 dc 3d 3d a4 6a 6a 3a 52 52 7a 36
RX0080: 06 20 a7 93 1b 34 dd 4c f5 ec
Zeros at offset 33 and 34 caused by reading empty RX FIFO which not possible
if DMA RX read was triggered by RX event. This mean DMA was triggered
by RX TAIL event.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
These structure members were removed in 2012 by the commit ffbbdd2132
("spi: create a message queueing infrastructure").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
xfer_completion isn't been used anywhere, so it can be
removed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The auxiliary spi supports only CPHA=0 modes as the first bit is
always output to the pin before the first clock cycle. In CPHA=1
modes the first clock edge outputs the second bit hence the slave
can never read the first bit.
Also the CPHA registers switch between clocking data in/out on
rising/falling edge hence depend on the CPOL setting.
Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This happens due to the fact, the the hardware was initialized
and reset at the begin and end of each transfer which results
in default state for all lines except chip-select which is
handled by the spi-subsystem as gpio-cs is used.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This should be fixed by commit 4c02cba18c
("pinctrl: bcm2835: Fix initial value for direction_output")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
__spi_split_transfer_maxsize() can be made static as it is only
used in this file.
This fixes the following sparse warning:
drivers/spi/spi.c:2266:5: warning: symbol '__spi_split_transfer_maxsize' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing spi_master_put for rockchip_spi_remove since
it calls spi_master_get already.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before registering master, driver enables runtime pm.
This patch pm_runtime_disable in err case while probing
driver to balance pm reference count.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_replace_transfers() returns error pointers on error, it never
returns NULL.
Fixes: d9f1212272 ('spi: core: add spi_split_transfers_maxsize')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Cc: linux-spi@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx empty irq can be disabled when all data was copied.
This prevents unnecessary interrupts while the last bytes are sent.
Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bitmasks for txempty and idle interrupts were interchanged.
Signed-off-by: Stephan Olbrich <stephanolbrich@gmx.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
ti-qspi controller provides mmap port to read data from SPI flashes.
mmap port is enabled in QSPI_SPI_SWITCH_REG. ctrl module register may
also need to be accessed for some SoCs. The QSPI_SPI_SETUP_REGx needs to
be populated with flash specific information like read opcode, read
mode(quad, dual, normal), address width and dummy bytes. Once,
controller is in mmap mode, the whole flash memory is available as a
memory region at SoC specific address. This region can be accessed using
normal memcpy() (or mem-to-mem dma copy). The ti-qspi controller hardware
will internally communicate with SPI flash over SPI bus and get the
requested data.
Implement spi_flash_read() callback to support mmap read over SPI
flash devices. With this, the read throughput increases from ~100kB/s to
~2.5 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In addition to providing direct access to SPI bus, some spi controller
hardwares (like ti-qspi) provide special port (like memory mapped port)
that are optimized to improve SPI flash read performance.
This means the controller can automatically send the SPI signals
required to read data from the SPI flash device.
For this, SPI controller needs to know flash specific information like
read command to use, dummy bytes and address width.
Introduce spi_flash_read() interface to support accelerated read
over SPI flash devices. SPI master drivers can implement this callback to
support interfaces such as memory mapped read etc. m25p80 flash driver
and other flash drivers can call this make use of such interfaces. The
interface should only be used with SPI flashes and cannot be used with
other SPI devices.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_split_transfers_maxsize method that splits
spi_transfers transparently into multiple transfers
that are below the given max-size.
This makes use of the spi_res framework via
spi_replace_transfers to allocate/free the extra
transfers as well as reverting back the changes applied
while processing the spi_message.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the spi_replace_transfers method that can get used
to replace some spi_transfers from a spi_message with other
transfers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI resource management framework used while processing a spi_message
via the spi-core.
The basic idea is taken from devres, but as the allocation may happen
fairly frequently, some provisioning (in the form of an unused spi_device
pointer argument to spi_res_alloc) has been made so that at a later stage
we may implement reuse objects allocated earlier avoiding the repeated
allocation by keeping a cache of objects that we can reuse.
This framework can get used for:
* rewriting spi_messages
* to fullfill alignment requirements of the spi_master HW
* to fullfill transfer length requirements
(e.g: transfers need to be less than 64k)
* consolidate spi_messages with multiple transfers into a single transfer
when the total transfer length is below a threshold.
* reimplement spi_unmap_buf without explicitly needing to check if it has
been mapped
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Braswell LPSS SPI controller actually has two chip selects and there
is no capabilities register where this could be found out. These two chip
selects are controlled by bits which are in slightly differrent location
than Broxton has.
Braswell Windows driver also starts chip select (ACPI DeviceSelection)
numbering from 1 so translate it to be suitable for Linux as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Intel LPSS SPI controllers, like the one in Braswell has these bits in
a different location so move these bits to be part of the LPSS
configuration.
Since not all LPSS SPI controllers support multiple native chip selects we
refactor selecting chip select to its own function and check
control->cs_sel_mask before switching to another chip select.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Windows Baytrail SPI host controller driver uses 1 as the first (and
only) value for ACPI DeviceSelection like can be seen in DSDT taken from
Lenovo Thinkpad 10:
Device (FPNT)
{
...
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (UBUF, ResourceTemplate ()
{
SpiSerialBus (0x0001, // DeviceSelection
PolarityLow, FourWireMode, 0x08,
ControllerInitiated, 0x007A1200, ClockPolarityLow,
ClockPhaseFirst, "\\_SB.SPI1",
0x00, ResourceConsumer,,)
This will fail to enumerate in Linux with following error:
[ 0.241296] pxa2xx-spi 80860F0E:00: cs1 >= max 1
[ 0.241312] spi_master spi32766: failed to add SPI device VFSI6101:00 from ACPI
To make the Linux SPI core successfully enumerate the device we provide a
custom version of ->fw_translate_cs() that translates DeviceSelection
correctly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In Windows it is up to the SPI host controller driver to handle the ACPI
DeviceSelection as it likes. The SPI core does not take any part in it.
This is different in Linux because we always expect to have chip select in
range of 0 .. master->num_chipselect - 1.
In order to support this in Linux we need a way to allow the driver to
translate between ACPI DeviceSelection field and Linux chip select number
so provide a new optional hook ->fw_translate_cs() that can be used by a
driver to handle translation and call this hook if set during SPI slave
ACPI enumeration.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic dma controller on Rockchips' platform cannot support
DMAFLUSHP instruction which make dma to flush the req of non-aligned
or non-multiple of what we need. That will cause an unrecoverable
dma bus error. The saftest way is to set dma max burst to 1.
Signed-off-by: Addy ke <addy.ke@rock-chips.com>
Fixes: 64e36824b3 ("spi/rockchip: add driver for Rockchip...")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Olof Johansson <olof@lixom.net>
cc: Doug Anderson <dianders@chromium.org>
cc: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of SPI_BCM2835AUX on GPIOLIB if COMPILE_TEST is
enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the AXI SPI Engine controller which is a FPGA
soft-peripheral which is used in some of Analog Devices' reference designs.
The AXI SPI Engine controller is part of the SPI Engine framework[1] and
allows memory mapped access to the SPI Engine control bus. This allows it
to be used as a general purpose software driven SPI controller. The SPI
Engine in addition offers some optional advanced acceleration and
offloading capabilities, which are not part of this patch though and will
be introduced separately.
At the core of the SPI Engine framework is a small sort of co-processor
that accepts a command stream and turns the commands into low-level SPI
transactions. Communication is done through three memory mapped FIFOs in
the register map of the AXI SPI Engine peripheral. One FIFO for the command
stream and one each for transmit and receive data.
The driver translates a spi_message in a command stream and writes it to
the peripheral which executes it asynchronously. This allows it to perform
very precise timings which are required for some SPI slave devices to
achieve maximum performance (e.g. analog-to-digital and digital-to-analog
converters). The execution flow is synchronized to the host system by a
special synchronize instruction which generates a interrupt.
[1] https://wiki.analog.com/resources/fpga/peripherals/spi_engine
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_ioremap_resource() validates its parameters and issues an error message if
needed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert dmaengine_terminate_all() calls to synchronous versions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a chance that chipselect is deasserted too early while the last
clock cycle is still running. Protocol analyzers will see this as a failed
last byte. This is more likely to occur with slow bitrates, for instance
at 25 kbps.
Reason for this is when using SPI mode 0 that both SPI host controller and
SPI slave will drive the data lines at the falling edge of clock signal
and sample at the rising edge. Receive FIFO gets the last bit now at the
rising edge and code sees transfer to be finished either by the interrupt
in PIO mode or by the DMA completion in DMA mode.
The SSP Time Out register SSTO should take care of delaying the
completion but it does not seems to have effect at least on Intel
Skylake and Broxton even when using long enough values. Depending on
timing code may get into point where chipselect is deasserted while the
last clock cycle is still running at its second half cycle.
Fix this by adding a wait loop in giveback() that waits until SSP becomes
idle before deasserting the chipselect.
Reported-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register writes here actually don't stop the SSP but clean and
disable interrupts and set the receive FIFO inactivity timeout to zero.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The non-DT platform that uses this driver (actually the AVR32) was taking a bad
branch for determining if the IP would use gpio for CS.
Adding the presence of DT as a condition fixes this issue.
Fixes: 4820303480 ("spi: atmel: add support for the internal chip-select of the spi controller")
Reported-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[nicolas.ferre@atmel.com: extract from ml discussion]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Transfer debug messages don't actually show is the transfer really using
DMA. Driver may fall back to PIO in case transfer size is not within the
certain limits or fails to map DMA buffers but debug messages don't reveal
that.
Move these debug messages further in pump_transfers() where the actual
transfer mode is known and use drv_data->dma_mapped flag instead of
chip->enable_dma for printing the mode.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In spi_imx_dma_transfer(), when desc_rx = dmaengine_prep_slave_sg()
fails, the context goes to label no_dma and then return. However,
the memory allocated for desc_tx has not been freed yet, which leads
to resource leak.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
These variables are always used uninitialized:
drivers/spi/spi-loopback-test.c: In function 'spi_test_run_iter':
drivers/spi/spi-loopback-test.c:768:17: warning: 'rx_count' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/spi/spi-loopback-test.c:762:17: warning: 'tx_count' may be used uninitialized in this function [-Wmaybe-uninitialized]
Adding an explicit initialization seems to be the only
workable solution here, to make the code behave correctly
and build without warning.
Fixes: 84e0c4e5e2 ("spi: add loopback test driver to allow for spi_master regression tests")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After removal of legacy PXA DMA code by the commit 6356437e65
("spi: spi-pxa2xx: remove legacy PXA DMA bits") the
CONFIG_SPI_PXA2XX_DMA follows the CONFIG_SPI_PXA2XX and cannot be disabled
alone. Therefore remove this config symbol and dead definitions from the
spi-pxa2xx.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A quiet release for SPI, not even many driver updates:
- Add a dummy loopback driver for use in exercising framework features
during development.
- Move the test utilities to tools/ and add support for transferring
data to and from a file instead of stdin and stdout to spidev_test.
- Support for Mediatek MT2701 and Renesas AG5 deices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWlNpkAAoJECTWi3JdVIfQ2rkH/j8fhCJVAGIkFs49+jk/+ZBR
NsvUEnPae9+e7vx/UBFNFJrM/1cpqy5VhDSbl/UnJLnOwiOOGeOR5H7S6YgDcW8m
gwgeCUJU5eqXx1tAuLJrD/qLya8uQQC6XaSlT2Du2Zr15EZ7tUvlRTva9M2nRQCC
OBo6f0FY+ptv/aNL7ME1WY5T4uQJC1FqRfvj0Cle1ZC8A1gONPoI7WLPasMckBEX
g9q76OUxLZ/I9CASUGbJYMtq/eBca5kq+dPcFLPfNTKKJk98TgRcJHzT+NW9igo2
D5r/pcsv8pt6H0Q2df8nkRzfvM/EPk/5VAYVJAxCogelKnqVaI8wlc6P7Rq5Mz0=
=0Z1l
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release for SPI, not even many driver updates:
- Add a dummy loopback driver for use in exercising framework
features during development.
- Move the test utilities to tools/ and add support for transferring
data to and from a file instead of stdin and stdout to spidev_test.
- Support for Mediatek MT2701 and Renesas AG5 deices"
* tag 'spi-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (69 commits)
spi: loopback: fix typo in MODULE_PARM_DESC
spi: sun4i: Prevent chip-select from being activated twice before a transfer
spi: loopback-test: spi_check_rx_ranges can get always done
spi: loopback-test: rename method spi_test_fill_tx to spi_test_fill_pattern
spi: loopback-test: write rx pattern also when running without tx_buf
spi: fsl-espi: expose maximum transfer size limit
spi: expose master transfer size limitation.
spi: zynq: use to_platform_device()
spi: cadence: use to_platform_device()
spi: mediatek: Add spi support for mt2701 IC
spi: mediatek: merge all identical compat to mtk_common_compat
spi: mtk: Add bindings for mediatek MT2701 soc platform
spi: mediatek: Prevent overflows in FIFO transfers
spi: s3c64xx: Remove unused platform_device_id entries
spi: use to_spi_device
spi: dw: Use SPI_TMOD_TR rather than magic const 0 to set tmode
spi: imx: defer spi initialization, if DMA engine is
spi: imx: return error from dma channel request
spi: imx: enable loopback only for ECSPI controller family
spi: imx: fix loopback mode setup after controller reset
...
There should be an 's' on "dump_message" so it matches the module_param.
Fixes: 84e0c4e5e2 ('spi: add loopback test driver to allow for spi_master regression tests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core calls set_cs before a transfer, but the SUN4I_CTL_CS_MANUAL
flag is only set in transfer_one. This leads to the following pattern on
the chip-select line (with runtime power-management on every transfer,
without it only on the first one):
activate, deactivate, activate, transfer, deactivate
Moving the configuration of the SUN4I_CTL_CS_MANUAL flag from transfer_one
to set_cs removes the double activation.
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_check_rx_ranges can always get executed independent of
if we have a real loopback situation.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename method spi_test_fill_tx to spi_test_fill_pattern
to better describe what it does.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the rx_buf does not get set with the
SPI_TEST_PATTERN_UNWRITTEN when tx_buf == NULL in the transfer.
Reorder code so that it gets done also under this specific condition.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl-espi hardware can trasfer at most 64K data so report teh
limitation.
Based on patch by Heiner Kallweit <hkallweit1@gmail.com>
CC: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi->irq was ignoring GpioInt property setting it to -1.
acpi_dev_gpio_irq_get returns and configure the slave IRQ according to
the ACPI slave node description.
It is now inline with devicetree behavior.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch merge all identical compat into on mtk_common_compat
and used for all compatible soc.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case where transfer length is not a multiple of 4, KASAN
reports 2 out-of-bounds memory accesses:
- mtk_spi_interrupt: ioread32_rep writes past the end of
trans->rx_buf.
- mtk_spi_fifo_transfer: iowrite32_rep reads past the end of
xfer->tx_buf.
Fix this by using memcpy on the remainder of the bytes.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
s5pv210 and exynos4 are now DT only platforms hence these
entries can now be safely removed from the match table.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TMODE available value is well defined and documented in the header
file. Use it and remove the comment.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Fix parent-device reference leak due to SPI-core taking an unnecessary
reference to the parent when allocating the master structure, a
reference that was never released.
Note that driver core takes its own reference to the parent when the
master device is registered.
Fixes: 49dce689ad ("spi doesn't need class_device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We use the spi_lock spinlock to protect against races between the device
being removed and file operations on the spidev. This means that in the
removal path all references to the device need to be done under lock as
in removal we dropping references to the device.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If SPI device supports DMA mode, but DMA controller is not yet
available due to e.g. a delay in the corresponding kernel module
initialization, retry to initialize SPI driver later on instead of
falling back into PIO only mode.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On SDMA initialization return exactly the same error, which is
reported by dma_request_slave_channel_reason(), it is a preceding
change to defer SPI DMA initialization, if SDMA module is not yet
available.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Limit SPI_LOOP mode to ECSPI controller (iMX.51, iMX53 and i.MX6) only since
there is no support in other families specific code for now.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If controller hold in reset it's not possible to write any
register except CTRL. So all other registers must be updated
only after controller bring out from reset.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added additional transfer length to test that are not a power of 2.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The test "two tx+rx transfers - alter second" actually modifies
the first not the second transfer, which - in conjunction with
testing the read data - results also in overwriting data read
earlier.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the reported printk format issues reported by kbuild-test-robot.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
adding the spi-loopback-test module to Kconfig and Makefile
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is submitting lots of distinct spi-messages messages
with all kinds of alignments and length pattern.
Also distinct kinds of transfer pattern tests are implemented
(rx, tx, rx/tx, tx+tx, tx+rx,...)
Right now on a raspberry pi 752 distinct spi_messages are executed
in 13 different scenarios.
Configuration of additional test-pattern is easy, so that when
new bugs in drivers get detected the relevant transfer pattern can
also get added to the test framework, so that such situations are
detected in other drivers as well.
The idea behind this driver is to make it possible to also detect
regressions in spi_master implementations when changes occur.
Potentially these tests could get executed automatically in a
test-server-farm.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
davinci_spi_bufs() uses wait_for_completion_interruptible()
without bothering to handle -ERESTARTSYS. Due to this,
sometime, it returns prematurely when a signal is received.
Since the return value is never checked, userspace eventually
receives a spurious -EIO.
To fix this, use un-interruptible wait_for_completion_timeout().
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSPI instances in Vybrid have a different amount of chip selects
and CTARs (Clock and transfer Attributes Register). In case of
DSPI1 we only have 2 CTAR registers and 4 CS. In present driver
implementation CTAR offset is derived from CS instance which will
lead to out of bound access if chip select instance is greater than
CTAR register instance, hence use single CTAR0 register for all CS
instances. Since we write the CTAR register anyway before each access,
there is no value in using the additional CTAR registers. Also one
should not program a value in CTAS for a CTAR register that is not
present, hence configure CTAS to use CTAR0.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pr_* macros are more prefferable than using printk. Start using
pr_* family of macros and define pr_fmt to be used with it.
While at it remove DRVNAME from an existing pr_info() as the name is now
being printed by pr_fmt.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we have a struct device available it is better to use dev_warn()
instead of printk.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to other controller type checks add check function for
IMX51. It includes IMX53 and IMX6.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to have different watermarks levels since they are the same.
Merge them into one WML parameter.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The overflow may happen due to rescheduling for another task and/or interrupt
if we enable SPI HW before starting RX DMA. So RX DMA enabled first to make
sure data would be read out from FIFO ASAP. TX DMA enabled next to start
filling TX FIFO with new data. And finaly SPI HW enabled to start actual
data transfer.
The risk rise in case of heavy system load and high SPI clock.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not only TX DMA should be terminated, but RX DMA also. It's required
to avoid accidential DMA memory writes from RX DMA channel and properly
terminate transaction.
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify spi-lm70llp driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch complains about space before closing brace.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch complains about the allignment with open parenthesis.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch was complaining about space after cast. But the cast to void
is not required at that place.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch complains about missing blank line after declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Loopback mode can be activated by setting bit LBC (LoopBack
Control) of register ECSPI_TESTREG.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify spi-butterfly driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch complains about the allignment with open parenthesis.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
checkpatch was complaining about space after cast. But the cast to void
is not required at that place.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark (and unmark) device nodes with the POPULATE flag as appropriate.
This is required to avoid multi probing when enabling and populating SPI
buses in DT overlays.
Based on commit 4f001fd301 ("i2c: Mark instantiated device nodes
with OF_POPULATE").
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Uninline spi_unregister_device() in preparation of adding more code to
it. Add kerneldoc documentation while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Occasionally the setup function will be called multiple times. Only request
the gpio the first time otherwise -EBUSY will occur on subsequent calls to
setup.
Reported-by: Joseph Bell <joe@iachieved.it>
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the topcliff-pch driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On 64-bit with CONFIG_SPI_DEBUG=y and #define VERBOSE:
drivers/spi/spidev.c:287:3: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type '__u32' [-Wformat=]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dw_spi_dma_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When submitting an identical spi_message multiple times via spi_sync
the spi_message.frame_length does not get reset to 0 in __spi_validate
before adding up all spi_transfer.len resulting in
frame_length > actual_length on all but the first spi_sync call.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
mtk_spi_probe() calls pm_runtime_enable(), after
pm_runtime_enable() is called, it should call
pm_runtime_disable() in the failure flow.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Handle EPROBE_DEFER explicitly so that we ensure that we get the DMA
channel specified in the device tree, instead of depending on the DMA
controller getting probed before us.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's not need to re-read and re-write SPI_CMD_REG, so remove it.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 8b136baa58 ("spi: pxa2xx: Detect number of enabled Intel LPSS SPI
chip select signals") added a block where lpss_ssp_setup() gets called
again for Intel LPSS SPI host controllers before checking number of chip
selects from the capabilities register.
There is no point in calling the function twice in probe so remove the
first call.
Reported-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds calls to pinctrl subsystem in order to switch pin states
on suspend/resume if you provide a "sleep" state in DT.
If no "sleep" state is provided in DT, these calls turn
to NOPs.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow transfers to set the transmission speed rather than using the
device max_speed_hz value. The SPI core makes sure that the speed_hz
value is always set on the transfer.
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s3c64xx platform data already contains a pointer to the
DMA filter function, but not to the associated data.
This simplifies the code and makes it more generic by
passing the data along with the filter function like
we do for other drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
With a 64-bit resource_size_t, we get a build warning on bcm63xx_spi_probe:
drivers/spi/spi-bcm63xx.c:565:16: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
As we are printing a resource, we can just use the %pr format
specifier that pretty-prints the address and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When only one device is present, it is not necessary to specify
cs_gpios, as the CS line can be controlled by the hardware
module.
Without this patch, older device tree bindings used before
37457607 "spi: mediatek: mt8173 spi multiple devices support"
would cause a panic on boot. This fixes the crash, and
re-introduces backward compatibility.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-bcm63xx.c: In function ‘bcm63xx_spi_setup_transfer’:
drivers/spi/spi-bcm63xx.c:207: warning: ‘clk_cfg’ may be used uninitialized in this function
While this is a false positive, it can easily be avoided by selecting
the default clock configuration first.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit ca5d248542 ("spi: Add THIS_MODULE to spi_driver in SPI core")
adds the new __spi_register_driver() function, but keeps the kerneldoc
for the spi_register_driver() function in place and forgets to add the
description for the new owner parameter.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the pxa2xx_spi_acpi_get_pdata() so that it can create platform data
also on platforms that do not support ACPI or if CONFIG_ACPI is not set.
Now it is expected that "pxa2xx-spi" platform device is either created with
explicit platform data or has an ACPI companion device.
However there is only little in pxa2xx_spi_acpi_get_pdata() that is really
dependent on ACPI companion and it can be reworked to cover also cases
where "pxa2xx-spi" device doesn't have ACPI companion and is created
without platform data.
Do this by renaming the pxa2xx_spi_acpi_get_pdata(), moving it outside of
CONFIG_ACPI test and changing a few runtime tests there to support non-ACPI
case. Only port/bus ID setting based on ACPI _UID is dependent on ACPI and
is moved to own function inside CONFIG_ACPI.
Purpose of this to support non-ACPI case for those PCI enumerated compound
devices that integrate both LPSS SPI host controller and integrated DMA
engine under the same PCI ID and which are registered in MFD layer instead
of in spi-pxa2xx-pci.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LPSS SPI in Intel Broxton is otherwise the same than in Intel Sunrisepoint
but it supports up to four chip selects per port and has different FIFO
thresholds. Patch adds support for two Broxton SoC variants.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI capabilities register located in private registers space of newer
Intel LPSS SPI host controllers tell in register bits 12:9 which chip
select signals are enabled.
Use that information for detecting the number of chip selects. For
simplicity we assume chip selects are enabled one after another without
disabled chip selects between. For instance CS0 | CS1 | CS2 but not
CS0 | CS1 | CS3.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS SPI host controllers in upcoming Intel platforms can have up
to 4 chip selects per port. Extend chip select control in
lpss_ssp_cs_control() by adding a code that selects the active chip
select output prior to changing the state. Detection for number of
enabled chip select signals will be added by another patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename a few defines that are specific to Intel LPSS SPI private
registers with LPSS prefix. It makes easier to distinguish them from
common defines.
Suggested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LS1043a and LS2080A in the Layerscape family also support DSPI, make
DSPI selectable for these hardwares.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
there's no need to call pm_runtime_get_sync()
followed by pm_runtime_put(). We should, instead,
just call pm_runtime_put_sync() and pm_runtime_disable().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some users have reported that in polled mode the driver fails randomly
to read the last word of the transfer.
The end condition used for the transmissions (in polled and irq mode)
has been the TX_EMPTY flag. But Lars-Peter Clausen has identified a delay
from the TX_EMPTY to the actual end of the data rx.
I believe that this race condition has not been detected until now
because of the latency added by the IRQ handler or the PCIe bridge.
This bugs affects setups with low latency access to the spi core.
This patch replaces the readout logic:
For all the words, except the last one, the TX_EMPTY flag is used (and
cached).
If !TX_EMPY or is the last word. The status register is read and the
RX_EMPTY flag is used.
The performance is not affected: there is an extra read of the
Status Register, but the readout can start as soon as there is a word
in the buffer.
Reported-by: Edward Kigwana <ekigwana@scires.com>
Initial-fix-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_register_driver helper macro that adds THIS_MODULE to
spi_driver for the registering driver. We rename and modify
the existing spi_register_driver to enable this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI controllers may need to be properly setup before chip selects
can be used. Therefore, wait until the spi controller has a chance
to perform their setup procedure before trying to use the chip
select.
This also insures that the chip selects pins are in a good
state before asseting them which otherwise may cause confusion.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset 0x60 is the offset of the data register defined as DW_SPI_DR in the
header file. Use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mt8173 IC spi HW has 4 gpio group, it's possible to support
max <= 4 slave devices, even mtk spi HW is not congruent to spi core.
1. When a device do a spi_message transfer, spi HW should know
which pad-group this device is on, and then writes pad-select
register.
2. Mtk pad-select register just selects which MISO pin HW will
receive data. For example, pad-select=1(select spi1 pins), HW just
receives data from spi1 MISO, but it still send waveform to all 4
group cs/clk/mosi. If cs pin in other groups is still spi mode,
after spi1 is selected(by active cs pin), devices on other group
will also be selected.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
controller_data is related with device, so move to master->setup
function.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mtk_spi_config() and mtk_spi_prepare_message() both initialize
spi register, so remove mtk_spi_config() and init all register
in mtk_spi_prepare_message().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building docs with make htmldocs, warnings about not having
a description for the return value are reported, i.e:
warning: No description found for return value of 'spi_register_driver'
Fix these by following the kernel-doc conventions explained in
Documentation/kernel-doc-nano-HOWTO.txt.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add more indentation to define lines for making them aligned with the
longest one. They would look messy after adding more long defines.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Upcoming Intel platforms use LPSS SPI_CS_CONTROL register bits 15:12 for
configuring the chip select polarities. Touch only chip select SW mode and
state bits when enabling the software chip select control in order to not
clear any other bits in the register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy noticed numeric unique device ID is unsigned integer so convert it
using kstrtouint(). Actually integer in ACPI 2.0 and later is 64 bits
litte-endian unsigned integer but quite certainly having so big value here
would mean something extra than just the SPI bus number so it won't hurt to
assume only lower 32 bits carry the bus number for now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we call pxa2xx_ssp_get_clk_div() from pump_transfers() we may derive
pointer to struct chip_data from struct drv_data like it's done in the rest
of the functions. This will make it less errorprone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The speed can be changed from transfer to transfer, that's why the messages
do not depict the actual values during ->setup(). Move debug messages from
->setup() to pump_transfers(). Get rid of leftovers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed problem with setting spi mode 0 or 1 after setting mode 2 or 3
SPI_MODE_0 and SPI_MODE_1 requires clock low when inactive. SPI_MODE_2
and SPI_MODE_3 requires clk high when inactive.
Currently driver can just set bits in fields SCLK_PHA (SPI Clock/Data
Phase Control), SCLK_POL (SPI Clock Polarity Control),
SCLK_CTL (controls the inactive state of SCLK) ans SS_POL (SPI SS
Polarity Select) of ECSPIx_CONFIGREG register.
This patch allows driver to clear corresponding bits in these fields.
Signed-off-by: Andrew Y. Kuksov <qxovxp@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all register definitions and structs into the driver. This allows
us dropping the platform_data struct and drop any arch specific
includes. Make use of different device names to identify the version of
the block we have.
Since we now have full control over the message width, we can drop the
size check, which was broken anyway, since it never set ret to any error
code.
Also since we now have no arch depedendent resources, we can now allow
compiling it for any arch, hidden behind COMPILE_TEST.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA-slave configuration depends on the whether <= 8 or > 8 bits
are transferred per word, so we need to call
atmel_spi_dma_slave_config() with the correct value.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since the "Switch driver to use transfer_one" change, the cs_change
behavior has changed and a channel chip select can still be
asserted when changing channel from a previous last transfer in a
message having the cs_change attribute.
Since there is no sense having multiple chip select being asserted at the
same time, disable all the remaining forced chip selects in a the
prepare_message called right before a spi_transfer_one_message call.
It ignores the current channel configuration in order to keep the
possibility to leave the chip select asserted between messages.
It fixes this bug on a DM8168 SoC ES2.1 Soc and an OMAP4 ES2.1 SoC.
It was hanging all the other channels transfers when a CHCONF_FORCE
is present on the wrong channel.
Fixes: b28cb9414d ("spi: omap2-mcspi: Switch driver to use transfer_one")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if GPIO pin is valid by API helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all users aware about calling dw_spi_remove_host() with properly set
parameter. Remove unneeded check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the driver to use unfied device property API instead of OF one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pdev member is not used anywhere, thus remove it. Moreover struct
dw_spi_pci becomes an equivalent of struct dw_spi and therefore remove entire
struct dw_spi_pci.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This helper disables SPI controller and sets clock to 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tx_threshold and rx_threshold variables are not used anywhere. Remove them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point to have a separate variable for speed in ->transfer_one().
While here, remove !chip->clk_div from a condition since it is assigned
simultaneously with chip->speed_hz. We can do this safely because
a) transfer speed can't be higher than max_freq and therefore chip->clk_div
can be 0 only when chip->speed_hz is 0, and
b) transfer speed can't be 0, otherwise we will get division by zero
exception.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry over spi->bits_per_word and Co from ->setup() in
struct chip_data since ->transfer_one() will anyway take the transfer
parameters from struct spi_transfer. This is since SPI core validates both
bits_per_word transfer parameter and defaults to spi->bits_per_word in case
that per transfer parameter is not set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we recalculate cr0 each time we start a transfer the chip_data->cr0
becomes redundant. Remove it and related pieces.
This is a follow up to commit 0ed36990a9 (spi: dw: Remove needless if
statements).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name of the master device is set during registrationg which happens after
we issue the error message. Change it to plain struct device * to see which
device registration failed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use spi->cs_gpio directly to remove the following build warning:
drivers/spi/spi-davinci.c:219:6: warning: 'gpio' may be used uninitialized in this function
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently word completion interrupt is fired for transfer of every
word(8bit to 128bit in size). This adds a lot of overhead, and decreases
r/w throughput. It hardly takes 3us(@48MHz) for 128bit r/w to complete,
hence its better to poll on word complete bit to be set in
QSPI_SPI_STATUS_REG instead of using interrupts.
This increases the throughput by 30% in both read and write case.
So, switch to polling mode instead of interrupts to determine completion
of word transfer.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per discussion [1] the best choice is to set closest speed which is not
going over the asked one.
Do the same approach for Intel Quark boards.
[1] http://www.spinics.net/lists/linux-spi/msg03389.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Propagate the actual return code of __spi_validate_bits_per_word() in
spi_setup().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the initialization order of the HW so that the interrupt
is only requested after the HW is initialized
Also the use of irq_of_parse_and_map is replaced by platform_get_irq.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are strange issues with the auxiliary spi device that result
in "lost" data in the RX path if the fifo is filled by too much
(even though the status register is checked if new data can get filled
in).
This has been observed primarily for the interrupt case.
Polling works fine, probably because the RX fifo is pulled immediately
when in the tight polling loop.
For that reason we have to limit the pending bytes to less than 15
when filling the fifo in interrupt mode.
There also was an issue returning the "wrong" last 1/2 bytes
of a transfer when the transfer is not a multiple of 3 bytes.
(this impacted polling and interrupt modes)
Also fixed an overflow in the estimation of the transfer time used
to decide if we run in interrupt or polling mode (found with the
spi-bcm2835.c driver originally).
Reported-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the initialization order of the HW so that the interrupt
is only requested after the HW is initialized
Also the use of irq_of_parse_and_map is replaced by platform_get_irq.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Writing invalid command to QSPI_SPI_CMD_REG will terminate current
transfer and de-assert the chip select. This has to be done before
calling spi_finalize_current_message(). Because
spi_finalize_current_message() will mark the end of current message
transfer and schedule the next transfer. If the chipselect is not
de-asserted before calling spi_finalize_current_message() then the next
transfer will overlap with the previous transfer leading to data
corruption.
__spi_pump_message() can be called either from kthread worker context or
directly from the calling process's context. It is possible that these
two calls can race against each other. But race is serialized by
checking whether master->cur_msg == NULL (pointer to msg being handled
by transfer_one() at present). The master->cur_msg is set to NULL when
spi_finalize_current_message() is called on that message, which means
calling spi_finalize_current_message() allows __spi_sync() to pump next
message in calling process context.
Now if spi-ti-qspi calls spi_finalize_current_message() before we
terminate transfer at hardware side, if __spi_pump_message() is called
from process context then the successive transactions can overlap.
Fix this by moving writing invalid command to QSPI_SPI_CMD_REG to
before calling spi_finalize_current_message() call.
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the IRQs for SPI client devices, registered via device-tree,
are mapped when the client devices are registered. If the corresponding
irq-chip has not been probed yet, then the probing of the client device
will fail and will not be retried. Resolve this by mapping the IRQ at
probe time and allow the probe to be deferred if the IRQ is not yet
available.
If of_irq_get() returns an error that is not -EPROBE_DEFER, then assume
that the SPI client does not have an IRQ and set the IRQ number to zero
(which is equivalent to irq_of_parse_and_map()).
This is based on some inputs from Thierry Reding <treding@nvidia.com>.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the message control word parameters part of the register offsets
array so we have them all in one struct.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct guard CONFIG_CPU_BIG_ENDIAN and the *be accessors to
follow native endianness on big endian systems.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm2835 has 2 auxiliary spi bus masters spi1 and spi2.
This implements the driver to enable these devices.
The driver does not implement native chip-selects but uses
the aribtrary GPIO-chip-selects provided by the spi-chipselect.
Note that this driver relies on the fact that
the clock is implemented by the clk-bcm2835-aux driver,
which enables/disables the HW block when requesting/releasing
the clock.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the bitbang driver to use the generic implementation of
transfer_one_message. This simplifies the bitbang driver code and
provides benefits like the statistics in the generic implementation.
Successfully tested on a IMX6-based system (spi-imx) and on a MIPS-based
router (OpenWRT with spi-ath79).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove an unneeded check. The SPI core (__spi_validate) takes care
that these fields are always populated.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not used since commit 8d94cc50aa ("[PATCH] spi: stabilize PIO mode
transfers on PXA2xx systems").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This was leftover from the legacy pxa2xx DMA implementation and not needed
anymore so remove it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the code by switching from devm_ioremap to devm_ioremap_resource.
Checking the result of platform_get_resource is not needed as
devm_ioremap_resource checks the provided resource argument for NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This makes possible to remove two if
statements and remove one code block that is never executed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get pointer to the struct acpi_device by using ACPI_COMPANION() macro. This
is more efficient than using ACPI_HANDLE() and acpi_bus_get_device().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Carry input clock of the controller in max_speed_hz of struct spi_master
instead of in own driver data. They mean the same thing and more over now
the max_speed_hz is not even set here.
As an added bonus this allows SPI core to validate that transfer speed is
not beyond the maximum input clock. This is not a problem in spi-pxa2xx as
the driver doesn't use transfer speed parameter directly but via input
clock divider calculation which will top at divide by one. However it's
better to validate speed before passing it here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
XTFPGA SPI controller has native endian registers.
Fix register acessors so that they work in big-endian configurations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
report transfer sizes as a histogram via the following files:
/sys/class/spi_master/spi*/statistics/transfer_bytes_histo_*
/sys/class/spi_master/spi*/spi*.*/statistics/transfer_bytes_histo_*
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There hasn't been need to carry chip->cr0 after SPI core started to
validate speed_hz and bits_per_word transfer parameters. That effectively
caused that pump_transfers() always recalculated it and practically
chip->cr0 is used locally in setup() for debug prints only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is continuation to previous commit by separating unindentation from
variable removal done in previous commit. As said SPI core have validated
both the speed_hz and bits_per_word and the if statement here evaluates
always to true.
Remove the test and unindent the code block accordingly. While at it remove
also needless "cr0 = chip->cr0" as cr0 will be overwritten anyway and fix
block comment style.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to carry spi->max_speed_hz and spi->bits_per_word from
setup() in "struct chip_data" since pump_transfers() will anyway take the
transfer parameters from "struct spi_transfer". This is since SPI core
validates both bits_per_word and speed_hz transfer parameters and defaults
to spi->bits_per_word and spi->max_speed_hz in case these per transfer
parameters are not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core makes sure that transfer speed is always set so code here writes
the same register with the same value twice. Code has been doing this from
the beginning.
This looks to me some sort of copy paste error so I'm removing the second
write. If this is not the case we can bring it back with a comment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Test for non-zero spi->max_speed_hz in dw_spi_setup() looks needless as
spi_setup() defaults to master->max_speed_hz in case it is not set. This
drivers sets the master->max_speed_hz based on max_freq data passed to it
via dw_spi_add_host() call. I suppose things have already fallen apart if
dw_spi_mmio_probe() or spi_pci_probe() ever passes zero max_freq.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This allows to remove related if
statements as they evaluate always to true and reduce indentation.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set.
This allows to remove a few if statements around per transfer bits_per_word
and speed_hz tests as they evaluate always to true.
Also defaulting word_len to 8 is needless since spi_setup() has already
made sure spi->bits_per_word is 8 in case it is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This allows to remove two needless tests
from uwire_txrx() and uwire_setup_transfer().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
thus the if statement here is needless as it will always call the
mpc512x_psc_spi_transfer_setup().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
chipselect (in the case of spi-gpio: spi_gpio_chipselect, which
calls gpiod_set_raw_value_cansleep) can sleep, so we should not
hold a spinlock while calling it from spi_bitbang_setup.
This issue was introduced by this commit, which converted spi-gpio
to cansleep variants:
d9dda5a191 "spi: spi-gpio: Use 'cansleep' variants to access GPIO"
Replacing the lock variable by a mutex fixes the issue: This is
safe as all instances where the lock is used are called from
contexts that can sleep.
Finally, update spi-ppc4xx and and spi-s3c24xx to use mutex
functions, as they directly hold the lock for similar purpose.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates both bits_per_word and speed_hz transfer parameters and
defaults to spi->bits_per_word and spi->max_speed_hz in case these per
transfer parameters are not set. This can simplify a little the
au1550_spi_setupxfer() as there is need to check only for valid
"struct spi_transfer" pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set so code here won't use the
chip->baud value (which is derived from spi->max_speed_hz).
Please note driver uses chip->baud at the beginning of message transmission
by calling the bfin_spi_restore_state() but then programs per transfer
speed in bfin_spi_pump_transfers(). I'm not familiar with the HW so I don't
know would it be possible to remove chip->baud completely by either using
constant value in bfin_spi_restore_state() or by removing the baud register
write there.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set so code here won't use the
chip->baud value (which is derived from spi->max_speed_hz).
Please note driver uses chip->baud at the beginning of message transmission
by calling the bfin_sport_spi_restore_state() but then programs per
transfer speed in bfin_sport_spi_pump_transfers(). I'm not familiar with
the HW so I don't know would it be possible to remove chip->baud completely
by either using constant value in bfin_sport_spi_restore_state() or by
removing the tclkdiv register write there.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core validates the transfer speed and defaults to spi->max_speed_hz in
case the transfer speed is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit adcbcfea15 ("spi: mediatek: fix spi clock usage error")
added a new sel_clk but introduced bugs in the error paths since
the wrong struct clk pointers are passed to PTR_ERR().
Fixes: adcbcfea15 ("spi: mediatek: fix spi clock usage error")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_property_read_u32 instead of of_get_property with return value
checks and endianness conversion.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove use of spi_unregister_master in remove function as
devm_spi_register_master in probe function automatically
handles it. To be compatible with the change, use direct
return instead of goto and remove unnedded label out.
Also, remove bcm53xxspi_bcma_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace all bcm_read* with (io)read. Due to this block following
system endianness, make sure we match that.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass 0 as the spi bus number, so we might as well hard code
it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass 8 for the number of chip selects, so we can as well
hardcode it to this number.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following warning:
drivers/spi/spi-bcm63xx.c:125:5: warning: unused variable 'rx_tail' [-Wunused-variable]
u8 rx_tail;
^
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify s3c64xx_spi_remove by replacing the clock disabling with calling
runtime PM suspend which does the same.
Waking up the device if it was suspended wouldn't be strictly needed
for this driver but using pm_runtime_get_sync is cleaner and makes
s3c64xx_spi_remove more consistent with the runtime PM handling in
s3c64xx_spi_setup.
pm_runtime_force_suspend does most of the work for us:
disabling the clocks, disabling runtime PM and setting it to
"suspended" state.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The runtime PM suspend / resume handlers take care of the enabling/
disabling the clocks already. Therefore replace the duplicated
clock handling with pm_runtime_force_suspend/resume.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the driver to make full use of runtime PM autosuspend.
Before only the SPI core was instructed to use autosuspend
by setting master->auto_runtime_pm. Nevertheless due to the missing
pm_runtime_use_autosuspend call autosuspend wasn't active.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During the last close we are freeing spidev if spidev->spi is NULL, but
just before checking if spidev->spi is NULL we are dereferencing it.
Lets add a check there to avoid the NULL dereference.
Fixes: 9169051617 ("spi: spidev: Don't mangle max_speed_hz in underlying spi device")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_PM is defined but not CONFIG_PM_SLEEP (this happens when
CONFIG_SUSPEND is not defined), there is the following warning:
drivers/spi/spi-atmel.c:1723:12: warning: ‘atmel_spi_suspend’ defined but not used [-Wunused-function]
drivers/spi/spi-atmel.c:1741:12: warning: ‘atmel_spi_resume’ defined but not used [-Wunused-function]
Enclose both atmel_spi_suspend and atmel_spi_resume in #ifdef
CONFIG_PM_SLEEP/#endif to solve that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a bug in the alignment checking of transfers,
that results in DMA not being used for un-aligned
transfers that do not cross page-boundries, which is valid.
This is due to a missconception of the meaning PAGE_MASK
when implementing that check originally - (PAGE_SIZE - 1)
should have been used instead.
Also fixes a copy/paste error.
Reported-by: <robert@axium.co.nz>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Mediatek spi HW can't set cs inactive(keep cs high) directly.
Instead, it supplies pause mode to do it indirectly. If driver
unsets SPI_CMD_PAUSE_MODE in CMD_REG, it also needs to reset
internal state machine to let cs inactive at once.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Actually, spi_master_put() after spi_alloc_master() must _not_ be followed
by kfree(). The memory is already freed with the call to spi_master_put()
through spi_master_class, which registers a release function. Calling both
spi_master_put() and kfree() results in often nasty (and delayed) crashes
elsewhere in the kernel, often in the networking stack.
This reverts commit eb4af0f534.
Link to patch and concerns: https://lkml.org/lkml/2012/9/3/269
or
http://lkml.iu.edu/hypermail/linux/kernel/1209.0/00790.html
Alexey Klimov: This revert becomes valid after
94c69f765f when spi-imx.c
has been fixed and there is no need to call kfree() so comment
for spi_alloc_master() should be fixed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On Intel Baytrail, there is case when interrupt handler get called, no SPI
message is captured. The RX FIFO is indeed empty when RX timeout pending
interrupt (SSSR_TINT) happens.
Use the BIOS version where both HSUART and SPI are on the same IRQ. Both
drivers are using IRQF_SHARED when calling the request_irq function. When
running two separate and independent SPI and HSUART application that
generate data traffic on both components, user will see messages like
below on the console:
pxa2xx-spi pxa2xx-spi.0: bad message state in interrupt handler
This commit will fix this by first checking Receiver Time-out Interrupt,
if it is disabled, ignore the request and return without servicing.
Signed-off-by: Tan, Jui Nee <jui.nee.tan@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch removes clk_disable_unprepare() in mtk_spi_remove().
clk_disable_prepare/unprepare must be balance, spi-clk is disabled
in mtk_spi_probe, so not needs to disable again.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The upper limit of Tx/Rx FIFO size is 64 word by the
specification of H/W. This patch corrects to 64 word from 256 word.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add SPI Master controller driver for the SPI interface on XLP8XX,
XLP3XX, XLP2XX, XLP9XX and XLP5XX family of Netlogic XLP MIPS64 processors.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM and use autosuspend instead of suspending the
SPI controller after each transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that most cleanup is done automatically the remove functions
can be significantly simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrate fsl-espi and fsl-spi to using the managed devm_ functions
for resource handling. This simplifies the cleanup.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
enable pause interrupt should use SPI_CMD_PAUSE_IE MACRO,
so fix it.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows drivers for devices connected via SPI to check if the
controller supports a given bits_per_word value during setup.
Currently any BPW value is accepted durings setup, and transfers
are rejected later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces *_time name in mtk_spi_prepare_transfer().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch replaces int with u32, deletes TAB, and defines
MTK_SPI_PAUSE_INT_STATUS marco.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
