Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.
$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support SG, software TSO, let's increase BD entry number.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enhance the code readable, let's factorize the
feature list.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP header checksum is calcalated by network layer in default.
To support software TSO, it is better to use HW calculate the
IP header checksum.
FEC hw checksum feature request the checksum field in frame
is zero, otherwise the calculative CRC is not correct.
For segmentated TCP packet, HW calculate the IP header checksum again,
it doesn't bring any impact. For SW TSO, HW calculated checksum bring
better performance.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.
And the patch also factorize the getting BD index to it own function.
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some specific configuration (VT6105M on Soekris 5510 and depending
on the device at the other end), fragmented packets were not transmitted
when forcing 100 full-duplex with autoneg disable.
This fix now write full-duplex chips register when forcing full or
half-duplex not only when autoneg is enable.
Signed-off-by: François Cachereul <f.cachereul@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
A malicious VF might try to starve the other VFs & PF by creating
contineous doorbell floods. In order to negate this, HW has a threshold of
doorbells per client, which will stop the client doorbells from arriving
if crossed.
The threshold currently configured for VFs is too low - under extreme traffic
scenarios, it's possible for a VF to reach the threshold and thus for its
fastpath to stop working.
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If L2FW utilized by the UNDI driver has the same version number as that
of the regular FW, a driver loading after UNDI and receiving an uncommon
answer from management will mistakenly assume the loaded FW matches its
own requirement and try to exist the flow via FLR.
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the phy access mode even in case of link-flap avoidance.
Signed-off-by: Yaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids clearing the RX polarity setting in KR mode when polarity lane
is swapped, as otherwise this will result in failed link.
Signed-off-by: Yaniv Rosner <yaniv.rosner@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the device address, the register number and the PHY ID for
which the MDIO read operation failed
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Check interrupt mode at the start of qlcnic_set_channels().
- Do not validate ring count if they are not going to change.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-allocate the physically contiguous DMA buffer used for
minidump collection at driver load time, rather than at
run time, to minimize allocation failures. Driver will allocate
the buffer at load time if PEX DMA support capability is indicated
by the adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently change the kzalloc() to devm_kzalloc() so freeing "ctlr"
here could lead to a double free.
Fixes: e194312854 ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here so we return directly instead of unwinding.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes:ee45fd92c739
("sfc: Use TX PIO for sufficiently small packets")
The linux net driver uses memcpy_toio() in order to copy into
the PIO buffers.
Even on a 64bit machine this causes 32bit accesses to a write-
combined memory region.
There are hardware limitations that mean that only 64bit
naturally aligned accesses are safe in all cases.
Due to being write-combined memory region two 32bit accesses
may be coalesced to form a 64bit non 64bit aligned access.
Solution was to open-code the memory copy routines using pointers
and to only enable PIO for x86_64 machines.
Not tested on platforms other than x86_64 because this patch
disables the PIO feature on other platforms.
Compile-tested on x86 to ensure that works.
The WARN_ON_ONCE() code in the previous version of this patch
has been moved into the internal sfc debug driver as the
assertion was unnecessary in the upstream kernel code.
This bug fix applies to v3.13 and v3.14 stable branches.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.
$ sudo ping -f -l 8 $BOARD_IP_ADDR
Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the packet "exceeded" condition in sh_eth_rx() when
RACT in an RX descriptor is not set and the "quota" is 0.
Otherwise, kernel panic happens because the "&n->poll_list" is deleted
twice in sh_eth_poll() which calls napi_complete() and net_rx_action().
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SXGBE_CORE_L34_ADDCTL_REG define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QLC_83XX_GET_LSO_CAPABILITY define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.
We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores. If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-11
This series contains updates to igb, i40e and i40evf.
Todd makes a change to igb to un-hide invariant returns by getting rid of
the E1000_SUCCESS define and converting those returns to return 0.
Jacob separates the hardware logic from the set function, so that we can
re-use it during a ptp_reset in igb. This enables the reset to return
functionality to the last know timestamp mode, rather than resetting the
value.
Ashish implements context flags for headwb and headwb_addr so that we
do not have to keep them always enabled.
Shannon updates the admin queue API for the new firmware, which adds
set_pf_content, nvm_config_read/write, replaces set_phy_reset with
set_phy_debug and removes nvm_read/write_reg_se. Cleans up the driver
to use the stored base_queue value since there is no need to read the
PCI register for the PF's base queue on every single transmit queue
enable and disable as we already have the value stored from reading
the capability features at startup.
Anjali changes the notion of source and destination for FD_SB in ethtool
to align i40e with other drivers. Adds flow director statistics to
the PF stats. Fixes a bug in ethtool for flow director drop packet
filter where the drop action comes down as a ring_cookie value, so allow
it as a special value that can be used to configure destination control.
Mitch fixes the i40evf to keep the driver from going down when it is
already in a down state. This prevents a CPU soft lock in napi_disable().
Also change the i40evf to check the admin queue error bits since the
firmware can indicate any admin queue error states to the driver via
some bits in the length registers.
Neerav separates out the DCB capability and enabled flags because currently
if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver inserts
a tag when transmitting a packet from the port even if there are no DCB
traffic classes configured at the port. So by adding the additional flag,
I40E_FLAG_DCB_CAPABLE, that will be set when the DCB capability is present
and the existing enabled flag will only be set if there are more than one
traffic classes configured at the port.
Greg fixes the i40e driver to not automatically accept tagged packets by
default so that the system must request a VLAN tag packet filter to get
packets with that tag. Greg also converts i40e to use the in-kernel
ether_addr_copy() instead of mempcy().
Jesse removes the FTYPE field from the receive descriptor to match the
hardware implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to read the PCI register for the PF's base queue on every single Tx
queue enable and disable as we already have the value stored from reading
the capability features at startup.
Change-ID: Ic02fb622757742f43cb8269369c3d972d4f66555
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A drop action comes down as a ring_cookie value, so allow it as
a special value that can be used to configure destination control.
Also fix the output to filter read command accordingly.
Change-ID: I9956723cee42f3194885403317dd21ed4a151144
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add members to stat struct to keep track of Flow director ATR and
SideBand filter packet matches.
Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change drops the FTYPE field from the Rx descriptor, to
match the hardware implementation.
Change-ID: I66d31d2b43861da45e8ace4fb03df033abe88bab
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FW can indicate any admin queue error states to the driver via some bits
in the length registers. Each time we process an admin queue message,
check these bits and log any errors we find. Since the VF really can't
do much, we just print the message and depend on the PF driver to clear
things up on our behalf.
Change-ID: I92bc6c53ce3b4400544e0ca19c5de2d27490bd0d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the filter created by the firmware with the default MAC address it
reads out of the NVM storage and a promiscuous VLAN tag and replace it
with a filter that will not accept tagged packets by default. The system
must request a VLAN tag packet filter to get packets with that tag.
Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver
inserts a tag when transmitting a packet from the port even if there
are no DCB traffic classes configured at the port.
This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set
when the DCB capability is present and the existing flag
I40E_FLAG_DCB_ENABLED will be set only if there are more than one
traffic classes configured at the port.
Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the device is down, there's no place to go but up, so don't try to go
down even more. This prevents a CPU soft lock in napi_disable().
Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In XL710 devices we program FD filter's fields from Tx perspective of the flow.
However the user interface exposed in ethtool should be compliant with the
previous generation of drivers where a filter src and dst field are from
the RX perspective. This patch changes the ethtool interface in this regard
to match the other drivers.
Change-ID: Iec6ccddd87357c4fb53ccf33aa0fae699faf70cf
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add set_pf_context, replace set_phy_reset with set_phy_debug, add
nvm_config_read/write, remove nvm_read/write_reg_se and add some
PHY types.
With these changes we bump the API version to 1.2.
Change-ID: I4dc3aec175c2316f66fc9b726b3f7d594699d84e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set appropriate fields in Tx queue configuration virtchnl message
to pf to enable headwb and setup headwb addr.
Then use that info from the VF to set headwb and headwb_addr instead of
always enabling them.
Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch separates the hardware logic from the set function, so that
we can re-use it during a ptp_reset. This enables the reset to return
functionality to the last known timestamp mode, rather than resetting
the value. We initialize the mode to off during the ptp_init cycle.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return a 0 directly rather than a constant.
Reported-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MAX_DMA_CHANNELS is defined in asm/scatterlist.h of the powerpc
architecture. Rename this #define in xgbe.h to avoid the
redefined warning issued during compilation.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following commit befdf89 "net/mlx4_core: Preserve pci_dev_data after
__mlx4_remove_one()", there are two mlx4 pci callbacks which will
attempt to release the mlx4_priv object -- .shutdown and .remove.
This leads to a use-after-free access to the already freed mlx4_priv
instance and trigger a "Kernel access of bad area" crash when both
.shutdown and .remove are called.
During reboot or kexec, .shutdown is called, with the VFs probed to
the host going through shutdown first and then the PF. Later, the PF
will trigger VFs' .remove since VFs still have driver attached.
Fix that by keeping only one driver entry which releases mlx4_priv.
Fixes: befdf89 ('net/mlx4_core: Preserve pci_dev_data after __mlx4_remove_one()')
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hypervisor driver tracks free slots and reserved slots at the global level
and tracks allocated slots and guaranteed slots per VF.
Guaranteed slots are treated as reserved by the driver, so the total
reserved slots is the sum of all guaranteed slots over all the VFs.
As VFs allocate resources, free (global) is decremented and allocated (per VF)
is incremented for those resources. However, reserved (global) is never changed.
This means that effectively, when a VF allocates a resource from its
guaranteed pool, it is actually reducing that resource's free pool (since
the global reserved count was not also reduced).
The fix for this problem is the following: For each resource, as long as a
VF's allocated count is <= its guaranteed number, when allocating for that
VF, the reserved count (global) should be reduced by the allocation as well.
When the global reserved count reaches zero, the remaining global free count
is still accessible as the free pool for that resource.
When the VF frees resources, the reverse happens: the global reserved count
for a resource is incremented only once the VFs allocated number falls below
its guaranteed number.
This fix was developed by Rick Kready <kready@us.ibm.com>
Reported-by: Rick Kready <kready@us.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A check on a memory allocation is checked incorrectly.
This was partly found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug that shows up with recv window sizes that exceed the size of
the RCV_BUFSIZ field in opt0 (>= 1024K). If the recv window exceeds
this, then we specify the max possible in opt0, add add the rest in via
a RX_DATA_ACK credits.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select the appropriate hw mtu index and initial sequence number to optimize
hw memory performance.
Add new cxgb4_best_aligned_mtu() which allows callers to provide enough
information to be used to [possibly] select an MTU which will result in the
TCP Data Segment Size (AKA Maximum Segment Size) to be an aligned value.
If an RTR message exhange is required, then align the ISS to 8B - 1 + 4, so
that after the SYN the send seqno will align on a 4B boundary. The RTR
message exchange will leave the send seqno aligned on an 8B boundary.
If an RTR is not required, then align the ISS to 8B - 1. The goal is
to have the send seqno be 8B aligned when we send the first FPDU.
Based on original work by Casey Leedom <leeedom@chelsio.com> and
Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently indirect interrupts for RDMA CQs funnel through the LLD's RDMA
RXQs, which also handle direct interrupts for offload CPLs during RDMA
connection setup/teardown. The intended T4 usage model, however, is to
have indirect interrupts flow through dedicated IQs. IE not to mix
indirect interrupts with CPL messages in an IQ. This patch adds the
concept of RDMA concentrator IQs, or CIQs, setup and maintained by the
LLD and exported to iw_cxgb4 for use when creating CQs. RDMA CPLs will
flow through the LLD's RDMA RXQs, and CQ interrupts flow through the
CIQs.
Design:
cxgb4 creates and exports an array of CIQs for the RDMA ULD. These IQs
are sized according to the max available CQs available at adapter init.
In addition, these IQs don't need FL buffers since they only service
indirect interrupts. One CIQ is setup per RX channel similar to the
RDMA RXQs.
iw_cxgb4 will utilize these CIQs based on the vector value passed into
create_cq(). The num_comp_vectors advertised by iw_cxgb4 will be the
number of CIQs configured, and thus the vector value will be the index
into the array of CIQs.
Based on original work by Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
