There is a spelling mistake in a DRM_DEBUG_DRIVER debug message.
Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to add new asic cases. This is a sw display
implementation, so just drop the error message so when
we add new asics, all we have to do is add the virtual
dce IP module.
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Comparing adev->family with CHIP constants is not correct.
adev->family can only be compared with AMDGPU_FAMILY constants and
adev->asic_type is the struct member to compare with CHIP constants.
They are separate identification spaces.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 62a3755341 ("drm/amdgpu: add si implementation v10")
Cc: Ken Wang <Qingqing.Wang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver does not support these sensors yet and there is no point in
creating sysfs attributes which will always return an error.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
for SOC15/vega10 the BACO reset & mode1 would introduce vram lost
in high end address range, current kmd's vram lost checking cannot
catch it since it only check very ahead visible frame buffer
v2:
cover NV as well
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
in_suspend flag should be set in amdgpu_device_suspend/resume in pairs,
instead of gfx10 ip suspend/resume function.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For picasso(adev->pdev->device == 0x15d8)&raven2(adev->rev_id >= 0x8),
firmware is sufficient to support gfxoff.
In commit 98f58ada2d, for picasso&raven2,
return directly and cause gfxoff disabled.
Fixes: 98f58ada2d ("drm/amdgpu/gfx9: update pg_flags after determining if gfx off is possible")
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since commit 04d5e27658 ("drm/amdgpu: Merge amdkfd into amdgpu"),
drivers/gpu/drm/amd/amdkfd/Makefile does not contain any syntax that
is understood by the build system.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needs ATPX rather than _PR3 to really turn off the dGPU. This can save
~5W when dGPU is runtime-suspended.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After commit a9f54ce3c6 ("drm/amd/display: Refactoring VTEM"),
there is no caller in tree.
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix for the commit below:
drm/amd/powerplay: implment sysfs feature status function in smu
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct the settings for auto mode and skip the unnecessary
settings for dcefclk and fclk.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement HW I2C enigne controller to be used by the RAS EEPROM
table manager. This is based on code from ATITOOLs.
v2:
Rename the file and all function prefixes to smu_v11_0_i2c
By Luben's observation always fill the TX fifo to full so
we don't have garbadge interpreted by the slave as valid data.
v3:
Remove preemption disable as the HW I2C controller will not
stop the clock on empty TX fifo and so it's not critical to
keep not empty queue.
Switch to fast mode 400 khz SCL clock for faster read and write.
v5:
Restore clock gating before releasing I2C bus and fix some
style comments.
v6:
squash in warning fix, fix includes (Alex)
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <Luben.Tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2:
PPSMC_MSG_RequestI2CBus seems not to work and so to avoid conflict
over I2C bus and engine disable thermal control access to
force SMU stop using the I2C bus until the issue is reslolved.
Expose and call vega20_is_smc_ram_running to skip locking when SMU
FW is not yet loaded.
v3:
Remove the prevoius hack as the SMU found the bug.
v5: Typo fix
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add RAS EEPROM table manager to eanble RAS errors to be stored
upon appearance and retrived on driver load.
v2: Fix some prints.
v3:
Fix checksum calculation.
Make table record and header structs packed to do correct byte value sum.
Fix record crossing EEPROM page boundry.
v4:
Fix byte sum val calculation for record - look at sizeof(record).
Fix some style comments.
v5: Add description to EEPROM_TABLE_RECORD_SIZE and syntax fixes.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <Luben.Tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 4f8bc72fbf.
It turned out that a single reserved queue wouldn't be
sufficient for page fault handling.
Signed-off-by: Gang Ba <gaba@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If CONFIG_DRM_AMD_DC_DSC_SUPPORT is not set, build fails:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_hwseq.c: In function dcn20_hw_sequencer_construct:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_hwseq.c:2099:28:
error: dcn20_dsc_pg_control undeclared (first use in this function); did you mean dcn20_dpp_pg_control?
dc->hwss.dsc_pg_control = dcn20_dsc_pg_control;
^~~~~~~~~~~~~~~~~~~~
dcn20_dpp_pg_control
Use CONFIG_DRM_AMD_DC_DSC_SUPPORT to guard this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8a31820b12 ("drm/amd/display: Make init_hw and init_pipes generic for seamless boot")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The navi10_message_map[] array has SMU_MSG_MAX_COUNT elements so the ">"
has to be changed to ">=" to prevent reading one element beyond the end
of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since reservation_object_wait_timeout_rcu is called with
interruptable set to false it's wrong to say
'or interrupted' in the error message.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The GRBM register interface is now capable of bursting 1 cycle per
register wr->wr, wr->rd much faster than previous muticycle per
transaction done interface. This has caused a problem where status
registers requiring HW to update have a 1 cycle delay, due to the
register update having to go through GRBM.
SW may operate on an incorrect value if they write a register and
immediately check the corresponding status register.
Registers requiring HW to clear or set fields may be delayed by 1 cycle.
For example,
1. write VM_INVALIDATE_ENG0_REQ mask = 5a
2. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. HW will reset VM_INVALIDATE_ENG0_ACK = 0 until invalidation is complete
3. write VM_INVALIDATE_ENG0_REQ mask = 5a
4. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. First read of VM_INVALIDATE_ENG0_ACK = 5a instead of 0
b. Second read of VM_INVALIDATE_ENG0_ACK = 0 because
the remote GRBM h/w register takes one extra cycle to be cleared
c. In this case, SW will see a false ACK if they exit on first read
Affected registers (only GC variant) | Recommended Dummy Read
--------------------------------------+----------------------------
VM_INVALIDATE_ENG*_ACK | VM_INVALIDATE_ENG*_REQ
VM_L2_STATUS | VM_L2_STATUS
VM_L2_PROTECTION_FAULT_STATUS | VM_L2_PROTECTION_FAULT_STATUS
VM_L2_PROTECTION_FAULT_ADDR_HI/LO32 | VM_L2_PROTECTION_FAULT_ADDR_HI/LO32
VM_L2_IH_LOG_BUSY | VM_L2_IH_LOG_BUSY
MC_VM_L2_PERFCOUNTER_HI/LO | MC_VM_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER_HI/LO | ATC_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER2_HI/LO | ATC_L2_PERFCOUNTER2_HI/LO
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-next-5.4-2019-08-23:
amdgpu:
- Enable power features on Navi12
- Enable power features on Arcturus
- RAS updates
- Initial Renoir APU support
- Enable power featyres on Renoir
- DC gamma fixes
- DCN2 fixes
- GPU reset support for Picasso
- Misc cleanups and fixes
scheduler:
- Possible race fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823202620.3870-1-alexander.deucher@amd.com
Fix image converter seam handling for 1024x1024 pixel hardware
limitation at the main processing section input, improve error
handling, and slightly optimize for 1:1 conversions.
Add support for newly defined 32-bit RGB V4L2 pixel formats.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXV/+phcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwJk/AP91Z8dTyRq2gaSJqRRYqe+dkyTI
SzfUKMA+nJG5ybRq4wD+MhLdbyq5MUEhg4ZDqvDjFKdXm8dO1YpBh4gkbj++gwA=
=PVTc
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2019-08-23' of git://git.pengutronix.de/pza/linux into drm-next
drm/imx: IPUv3 image converter fixes and improvements
Fix image converter seam handling for 1024x1024 pixel hardware
limitation at the main processing section input, improve error
handling, and slightly optimize for 1:1 conversions.
Add support for newly defined 32-bit RGB V4L2 pixel formats.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1566573659.23587.2.camel@pengutronix.de
- Fixes on DP MST (Ville)
- More GTT and Execlists fixes and improvements (Chris)
- Code style clean-up on hdmi and dp side (Jani)
- Fix null pointer dereferrence (Xiong)
- Fix a couple of missing serialization on selftests (Chris)
- More vm locking rework (Chris)
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdXo8xAAoJEPpiX2QO6xPKiGcH/RKd+kjlORORlcLFn8YLhjui
5GM/+8TArbFND/8Ld+dTNro/YKGH4yB1Q/XESKZFWrVAGc8l6ikIY8lN8q1oV2lL
k6na3kO5uO4dZt+k7Y/uHOSxzs437pxeqjTkZsYzpjy9fR3ZvrteL5wEWRFbuh9q
JiCoqoPH1VbaaaFOvj/UlKzoEP2bMclzq/oE6B19XcLA51d2vfQ6cfufffw3sj9q
ulx/AMvdCcXTVZ8zIhY4SjaQSCRC6TeMBmWxLfHKCn3AZ4XR2riNRHx4Fylcyyzf
yN/EEIs/AUW5LaC34tZlu57kkc75QRllkDyozox6a6EH3QU7VkFoOIA3deyBMz4=
=bilG
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2019-08-22' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- More TGL enabling work (Michel, Jose, Lucas)
- Fixes on DP MST (Ville)
- More GTT and Execlists fixes and improvements (Chris)
- Code style clean-up on hdmi and dp side (Jani)
- Fix null pointer dereferrence (Xiong)
- Fix a couple of missing serialization on selftests (Chris)
- More vm locking rework (Chris)
drm-intel-next-2019-08-20:
- GuC and HuC related fixes and improvements (Daniele, Michal)
- Improve debug with more engine information and rework on debugfs files (Chris, Stuart)
- Simplify appearture address handling (Chris)
- Other fixes and cleanups around engines and execlists (Chris)
- Selftests fixes (Matt, Chris)
- Gen11 cache flush related fixes and improvements (Mika)
- More work around requests, timelines and locks to allow removal of struct_mutex (Chris)
- Add missing CML PCI ID (Anusha)
- More work on the new i915 buddy allocator (Matt)
- More headers, files and directories reorg (Daniele)
- Improvements on ggtt’s get pdp (Mika)
- Fix GPU reset (Chris)
- Fix GPIO pins on gen11 (Matt)
- Fix HW readout for crtc_clock in HDMI mode (Imre)
- Sanitize display Phy during unitit to workaround messages of HW state change during suspend (Imre)
- Be defensive when starting vma activity (Chris)
- More Tiger Lake enabling work (Michel, Daniele, Lucas)
- Relax pd_used assertion (Chris)
drm-intel-next-2019-08-13:
- More Tiger Lake enabling work (Lucas, Jose, Tomasz, Michel, Jordan, Anusha, Vandita)
- More selftest organization reworks, fixes and improvements (Lucas, Chris)
- Simplifications on GEM code like context and cleanup_early (Chris, Daniele)
- GuC and HuC related fixes and improvements (Daniele, Michal, Chris)
- Some clean up and fixes on headers, Makefile, and generated files (Lucas, Jani)
- MOCS setup clean up (Tvrtko)
- More Elkhartlake enabling work (Jose, Matt)
- Fix engine reset by clearing in flight execlists requests (Chris)
- Fix possible memory leak on intel_hdcp_auth_downstream (Wei)
- Introduce intel_gt_runtime_suspend/resume (Daniele)
- PMU improvements (Tvrtko)
- Flush extra hard after writing relocations through the GTT (Chris)
- Documentations fixes (Michal, Chris)
- Report dma_reserv allocation failure (Chris)
- Improvements around shrinker (Chris)
- More improvements around engine handling (Chris)
- Also more s/dev_priv/i915 (Chris)
- Abstract display suspend/resume operations (Rodrigo/Jani)
- Drop VM_IO from GTT mappings (Chris)
- Fix some NULL vs IS_ERR conditions (Dan)
- General improvements on error state (Chris)
- Isolate i915_getparam_iocrtl to its own file (Chris)
- Perf OA object refactor (Umesh)
- Ignore central i915->kernel_context and allocate it directly (Chris)
- More fixes and improvements around wakerefs (Chris)
- Clean-up and improvements around debugfs (Chris)
- Free the imported shmemfs file for phys objects (Chris)
- Many other fix and cleanups around engines and execlists (Chris)
- Split out uncore_mmio_debug (Daniele)
- Memory management fixes for blk and gtt (Matt)
- Introduction of buddy allocator to handle huge-pages for GTT (Matt)
- Fix ICL and TGL PG3 power domains (Anshuman)
- Extract GT IRQ to gt/ (Andi)
- Drop last_fence tracking in favor of whole vma->active (Chris)
- Make overlay to use i915_active instead of i915_active_request (Chris)
- Move misc display IRQ handling to its own function (Jose)
- Introduce new _TRANS2() macro in preparation for some coming PSR related work (Jose)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823051435.GA23885@intel.com
Hisilicon developed hibmc_drm for their arm64 based soc and did not
intend for this driver to be used on any other architecture than arm64.
Using it on amd64 leads to incorrect video modes being used, making
the screen unreadable, forcing users to manually blacklist the module
on the kernel command line to use the d-i server installer or any
graphical sessions.
Make CONFIG_DRM_HISI_HIBMC firmly depend on ARM64 to ensure it is not
built for other architectures.
Signed-off-by: Matthew Ruffell <matthew.ruffell@canonical.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Remove boilerplate code by using macro module_pci_driver.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
[WHY] value of dchub_ref_clock is decided by dchubbub global timer
settings which is programmed by vbios command table disp_init.
for multi-GPU case, vbios is posted only for primary GPU. without
vbios posted for the secondary GPU, value of dchub_ref_clock is not
set properly. this value will affect dcn bandwidth calcuation and
cause underflow. user will see screen flicking during driver
installation for dual GPU case.
[HOW] dc init_hw always call vbios command table disp_init to
make sure dchubbub global timer is configured and enable.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The register LVTMA_PWRSEQ_CNTL is used to determine the power state of the
embedded display. Currently we do not actually read this register's values,
so during power down we think that this display is already off, so we skip
calling into VBIOS to actually turn it off.
[How]
- add relevant fields to shift / mask initialization
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous workaround to prevent a vsync flip to be converted
to immediate flip is no longer needed, and is risky because
there are cases where it can result in infinite loop.
[how]
Remove wait loop (which is potentially infinite) before locking
pipe
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should be using the ddc_num from res_caps. As the
pipe count != number of i2c resources.
[How]
Use ddc_num from res_cap instead of pipe count.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Existing HW Features, HW Diags test requested that the
registers be exposed.
[How]
Add V_TOTAL_MID to existing DC structures.
Make sure values are passed down throughout DC
Add Register definition.
Program the additional registers
Add additional Logic for V_TOTAL_CONTROL.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Calculating DCFCLK DS time requires calculating
delivery time for luma/chroma, but this value is
not calculated in DMLv2, it was inadvertently
removed when porting DMLv2
[how]
Add the calculation back
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM provides drm_dp_mst_dump_topology, which prints
useful information about MST devices
Hook this up to a debugfs file named amdgpu_mst_topology
Signed-off-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OS will reserve HW state in UEFI mode.
Driver init_hw reset to RGB which caused HDMI green in YCbCr mode.
read HW blank_color based on acc_mode.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.
[How]
Add logging in dc.
Fix formatting for easier graphing.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] HW rotation is not enabled. Calculations for cursor rotation
are wrong for the values passed to set_cursor_position.
[How] Swap Src rect and height and vertically mirror surface for
the correct surface rotation direction. Cursor position is rotated
according to angle. Offset calculations are tweaked for non-rotated
cursor hotspot and width/height.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to have the ability to to tell us set degamma on the cursor.
[How]
Pass a flag down to register programming that tells us if the
current surface format needs cursor degamma.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update bw validation to use prev and next odm pipe pointers
for populating dml inputs.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to memset all odm pipes when calling dc_remove_stream_from_ctx
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn20 requires special casing for odm.
This change treats odm as alternative to mpc tree on dcn20.
This is planned to be fixed in a future refactor
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
num_slices_h was not being checked
[How]
Fix the typo and check num_slices_h
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ODM next and prev pipe were missing from dc_copy_state
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In newer hardware MANUAL_FLOW_CONTROL is not a trigger bit. Due to this
front porch is fixed and in these hardware freesync does not work.
[How]
Change the programming to generate a pulse so that the event will be
triggered, front porch will be cut short and freesync will work.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With visual confirm enabled, displays where ODM combine is enabled
has a test pattern stuck on the right half of the display even
though the display is unblanked.
[how]
Add a condition to not show the colour ramp test pattern when the
display is unblanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Video Timing Extended Metadata packet (VTEM) is not
specific to freesync. So move it out of freesync module
[How]
- Moved VTEM from freesync module to info_packet module
- Created new structure for VTEM parameters that can be used for VRR
and FVA
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Ahmad Othman <Ahmad.Othman@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This function is not being used, it was left in
when introducing DCN2
[How]
Remove the function
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
during a refactor a redundant code that has unknown behaviour was added.
[how]
removed old bad code
Fixes: 8a31820b12 ("drm/amd/display: Make init_hw and init_pipes generic for seamless boot")
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How] Allocate memory for default page and program memory block addr
into default page addr register.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IEEE OUI will now be used while referring to certain vendors.
instead of normal index
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before a statically allocated PPS data structure, that did
get zeroed-out at startup, had been re-used for making packed PPS
SDP. With S3 fix, using a non-initialized PPS data structure was
introduced, while wrongly assuming it'd get initialized before it's
populated. As a consequence 'vbr_enable' and perhaps some other
fields are left uninitialized when making packed PPS SDP. This can
affect 'simple_422' as well because of the way PPS SDP packing is
done (the fields are not masked first, only shifted). The behavior
will be different, depending on the content of uninitialized data.
[how]
Zero-out PPS data structure at initialization time before it's
populated
Fixes: 1a9e3d4569 ("drm/amd/display: Set DSC before DIG front-end is connected to its back-end")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add new function to get the voltage at the end of
dcn_validate_bandwidth, to check against the
highest voltage we allow.
Created a stub to allow for optimizations
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding NULL checks to various parameters in log_tf, to avoid
nullptr errors
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Nikola Cornij <Nikola.Cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the writeback Hratio and Vratio in dml.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous odm change broke stream enable by always setting
n_multiply as if odm was on.
This fixes the check for odm by making sure opp count is >1
rather than not 0.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABM 2.3 firmware expects information in iRAM that differs from previous
versions of ABM, so a mechanism is required to provide it with that
information.
[How]
Extend the existing iRAM definition to include parameters added by
ABM 2.3, and load it if DMCU is running ABM 2.3.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With Scatter Gather enabled, HUBP underflows during MPO enabled video
playback. hubp_init has a register write that fixes this problem, but
the register is cleared when HUBP gets power gated.
[how]
Make a call to hubp_init during enable_plane, so that the fix can
be applied after HUBP powers back on again.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable_audio_stream gets enum option as a paramenter which will decide
if we free acquired resources or not. However checks for the option is
guarded by the other condition which check if audio stream is getting
diabled more than once. With both conditions combined, if we attempt to
disable audio stream twice in a row, first with keep and second with
free as an option, we will never free any resources, which will make
system think there is audio endpoint connected even after we plug out
the device
[How]
Get rid of option as parameter to disable_audio_stream and move the part
of the code that free acquired resources to outside where to keep or to
free resources is actually determined
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dig_encoder_sel_to_atom will always return zero on any ASIC version
past DCE80 since programming of the FE selection is handled by
driver, but the translation code was left in the function, making
it look like a coding error.
[How]
Remove code that has no effect, and replace with a comment describing
why it returns zero.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.
Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.
Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that we properly handle them on older asics.
Fixes: 3ff985485b ("drm/amdgpu: Export function to flush TLB of specific vm hub")
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a dcfeaturemask flag for mclk switching. Disable by default;
enable once the feature has seen more testing.
Set amdgpu.dcfeaturemask=2 on the kernel command line in grub
to enable this.
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly set all_displays_in_sync so that when the data is
propagated to powerplay, it's set properly and we can enable
mclk switching when all monitors are in sync.
v2: fix logic, clean up
v3: check for blending chains, simplify logic
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If DC has synced the displays, we can enable mclk switching to
save power.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If DC has synced the displays, we can enable mclk switching to
save power.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the 40.46 SMU release, they changed CurrSocketPower to
AverageSocketPower, but this was changed back in 40.47 so just check if
it's 40.46 and make the appropriate change
Tested with 40.45, 40.46 and 40.47 successfully
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the virtual function PCI device id.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Frank.Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix other navi asic set peak performance level error.
because the navi10_ppt.c will handle navi12 14 asic,
it will use navi10 peak value to set other asic, it is not correct.
after patch:
only navi10 use custom peak value, other asic will used default value.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use unsigned long type for the same ras count variable.
This will avoid overflow on 64 bit system.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613115749.GC26335@kroah.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190704023557.4551-1-huangfq.daxian@gmail.com
Some, mostly Fermi, vbioses appear to have zero max voltage. That causes Nouveau to not parse voltage entries, thus users not being able to set higher clocks.
When changing this value Nvidia driver still appeared to ignore it, and I wasn't able to find out why, thus the code is ignoring the value if it is zero.
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is something that got noticed a while ago back when I was fixing a
large number of runtime PM related issues in nouveau, but never got
fixed:
https://patchwork.freedesktop.org/series/46815/#rev7
It's not safe to iterate the entire list of CRTCs in
nv50_disp_atomic_commit(), as we could be doing a non-blocking modeset
on one CRTC in parallel with one or more other CRTCs. Likewise, this
means it's also not safe to do so in order to track runtime PM state.
While this code is certainly wrong, so far the only issues I've seen
this cause in the wild is the occasional PM ref unbalance after an
atomic check failure + module reloading (since the PCI device will
outlive nouveau in such scenarios).
So, do this far more elegantly: grab a runtime PM ref across the modeset
and commit tail, then grab/put references for each CRTC enable/disable.
This also ends up being much simpler then the previous broken solution
we had.
Finally, since we've removed all it's users: get rid of
nouveau_drm->have_disp_power_ref.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Originally when trying to fix the issue of runtime PM references with
non-blocking CRTCs on nv50, I ended up stumbling on this code when
trying to remove nouveau_drm->have_disp_power_ref, and attempted to fix
it to remove the dependency on have_disp_power_ref. However, Ilia Mirkin
pointed out that this code is actually completely useless, as pre-nv50
never had runtime PM support in the first place! Go figure.
So, since it's useless just get rid of it. Note that since the only
thing nouveau_crtc_set_config() was doing was grabbing a runtime PM ref,
calling drm_crtc_helper_set_config() then dropping the ref; we can just
remove the function entirely and just call drm_crtc_helper_set_config()
directly.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Added GPIO is "Power Alert". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.
This GPIO can be found on Tesla and sometimes on Fermi GPUs.
Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Added GPIO is "Thermal and External Power Detect". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.
This GPIO can be found in Rankine and Curie and rarely on Tesla GPUs
VBIOS.
Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently, nouveau doesn't check if GPU is missing power. This
patch makes nouveau fail when this happens on latest GPUs.
It checks GPIO function 121 (External Power Emergency), which
should detect power problems on GPU initialization.
This can be disabled with nouveau.config=NvPowerChecks=1
Tested on TU104, GP106 and GF100.
v3:
* Add config override for disabling power checks
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
One gpio was in wrong place, moved it for better readability.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's already a condition in place which attempts to detect this, but
since we've begun to require a PMU subdev even on boards where we don't
load a custom FW, it's become inaccurate.
This will prevent unnecessarily running a periodic fan update thread on
GP100 and newer, where we don't yet override the default PMU FW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Has a nice side-effect that we only update HW for this when it changes now,
rather than every time we do a page flip.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
zpos normalisation uses plane id to determine ordering for duplicate zpos
values, and we likely want to keep primary plane on the bottom here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We have some of this open-coded already, use the helper to prevent problems
when adding (for example) support for the alpha property.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
For GF119:GV100, we can enable DEGAMMA/CTM/GAMMA. For earlier GPUs, as
there is no CTM, having both degamma and gamma is a bit pointless. Later
GPUs currently lack an implementation.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The overlay logic can only do colorkey-based selection, not
alpha-blending.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pascal was particularly incorrect, as the register changed to be more in the
same format as the MMU fault buffers are.
Shouldn't have impacted much more than confusing MMU fault log messages.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Would like to be able to reuse gf100_fifo_intr_fault() for (some of) the
later chipsets too, as it's identical.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signal that the reset sequence has completed.
This opcode signals that the software reset sequence has completed.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signal that the reset sequence has begun.
This opcode signals that the software reset sequence has begun.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Absence of a TMDS Info Table is common on Optimus setups where the NVIDIA
gpu is not connected directly to any outputs.
Reporting an error in this scenario is too harsh. Accordingly, change the
error message to an info message.
By default the error message also causes a boot flicker for these sytems.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We now have per-device driver_features, so let's use that
to disable atomic only for pre-nv50.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Older hardware seems to want 0..1024 values, while new hardware takes
0..1 values. We set the gain to 1024 for the earlier display classes.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On Turing, an input LUT is required to transform inputs in fixed-point
formats to FP16 for the internal display pipe. We provide an identity
mapping whenever a window is enabled for this reason.
HW has error checks to ensure when the input is already FP16, that the
input LUT is also disabled.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*kind) + sizeof(*kind->data) * mmu->kind_nr;
with:
struct_size(kind, data, mmu->kind_nr)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Drop use of the deprecated drmP.h file from drm/nouveau.
Build tested using allyesconfig and allmodconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Drop include of the deprecated drmP.h from all nouveau heder files.
This allows us to remove drmP.h from all .c files without any
side-effects in a follow-up commit.
Build tested using allyeyconfig and allmodconfig
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Drop the deprecated drmP.h header from nouveau_drv.h.
Fix fallout in other parts of the driver.
Build tested using allmodconfig and allyesconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The DRM_UDELAY is a simple wrapper for udealy() and to be consistent
call udelay() direct like in may other places.
This avoids the need to pull in drm_os_linux.h when we later
drop drmP.h uses in nouveau.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There is a spelling mistake in a warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fix sparse warning:
drivers/gpu/drm/nouveau/nvkm/subdev/secboot/acr_r352.c:1092:1:
warning: symbol 'acr_r352_ls_gpccs_func' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was broken by a previous change switching to cached fw_info.
Fixed by inverting a valid bool check.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=111432
Fixes: 9adc8050bf ("drm/amd/display: make firmware info only load once during dc_bios create")
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will enable indirect SRAM loading for VCN DPG mode initialization.
Signed-off-by: Thong Thai <thong.thai@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 444a0fea51.
We are ready to enable it now.
Signed-off-by: Thong Thai <thong.thai@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates gc/sdma goldensetting for renoir
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid the dpm frequence range get failed when DPM enabled and it
will be enabled later once handle well the feature bit map struct.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable the dpm feature for the renoir.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable SDMA PG flag during device ip early init.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for SDMA clockgating on RN.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable DF clock gating during DF IP early init.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable athub MG and LS clock gating.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable IH clock gating during IH block initialized.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds add DPMCLOCKS table implementation
Rename smu_populate_smc_pptable to smu_populate_smc_tables
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initialize smu tables for renoir:
WATERMARKS/DPMCLOCKS/SMU_METRICS
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add and map smu tables for renoir
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check whether the message mapping is valid
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For renoir, it should use mmSMUIO_GFX_MISC_CNTL to check
gfxoff status. For the first time to enter gfxoff status,
it maybe takes about one second more. So just set the max
timeout to 5s.
GFXOFF_STATUS(bits 2:1)'s description is below:
0=GFXOFF(default).
1=Transition out of GFX State.
2=Not in GFXOFF.
3=Transition into GFXOFF.
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates gfxoff feature.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add set_gfx_cgpg implement
v2: check if using sw_smu (Alex)
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This interface support SMU_MSG_GetDriverIfVersion
and SMU_MSG_GetSmuVersion checking.
v2: squash in driver_if changes (Alex)
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All apu series need powerup sdma and vcn via smu messages.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Thus VCN can be powered up for normal operations
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renoir DPM is not functional so far, we skip it for the comment.
Will revert this patch once SMU 12 is functional.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.Implement PowerUpSDMA/PowerDownSDMA interfaces in the swSMU for renoir
2.adjust smu ip block ahead of gfx&sdma ip block
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
