For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RCar Gen2 and later implementations of TMIO/SDHI have their own set of
features and additions. FAST_CLK_CHG is just one of them and I see a few
others being added soon. Some may work on older chipsets but this needs
to be tested case by case. Instead of adding a bunch of flags for each
feature, add a global RCar2+ one for now. We can still break out
features if the need arises.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The docs for RCar Gen2 & 3 I have access to, mention delays of 5ms after
stop and 1ms after start. Make it possible to apply these values.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dma_request_slave_channel_compat() in tmio_mmc_dma
needs .chan_priv_tx/.chan_priv_rx. But these are copied from
sh_mobile_sdhi only, and sh_mobile_sdhi_info is now almost
same as tmio_mmc_data except .chan_priv_?x.
sh_mobile_sdhi_info can be replaced to tmio_mmc_data, but it is
used from ${LINUX}/arch/arm/mach-shmobile, ${LINUX}/arch/sh.
So, this patch adds .chan_priv_?x into tmio_mmc_data as 1st step,
and sh_mobile_sdhi driver has dummy operation for now.
It will be replaced/removed together with platform data replace.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
tmio_mmc_host has .enable_dma callback now.
We don't need TMIO_MMC_HAVE_CTL_DMA_REG anymore.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma_rx_offset is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .alignment_shift is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .bus_shift is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .multi_io_quirk is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_disable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_enable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .write16_hook is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio_mmc driver is using tmio_mmc_data for driver/platform
specific data/callback, and it is needed for tmio_mmc_host_probe()
function. Because of this style, include/linux/mfd/tmio.h header has
tmio driver/framework specific data which is not needed from platform.
This patch adds new tmio_mmc_host_alloc/free() as cleanup preparation.
tmio driver specific data/callback will be implemented in tmio_mmc_host,
and platform specific data/callback will be implemented in tmio_mmc_data
in this cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, tmio_mmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controller is supporting actual clock on SD_CLK_CTRL :: DIV[7:0].
Renesas SH-Mobile SDHI doesn't support,
but, Renesas R-Car SDHI supports it.
This patch adds new TMIO_MMC_CLK_ACTUAL flag for it.
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new TMIO_MMC_HAVE_CTL_DMA_REG flag,
and remove Renesas specific #ifdef from tmio driver
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI has "Multiple Block Transfer Mode" settings
on SD_CMD register which controls CMD12 automatically.
This patch cares it, because
CMD12 is not needed when CMD53 (= SD_IO_RW_EXTENDED)
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Basically, SD_BUF0 Tx/Rx addresses are same
in normal TMIO controller,
but, it is different on Renesas R-Car SDHI controller
if it uses DMAC
(Rx address needs to add 0x2000 to Tx address)
This patch adds new .dma_rx_offset and cares it
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The accessibility checking method to the higher register was added by
69d1fe18e9 (mmc: tmio: only access registers above 0xff, if available)
But, it doesn't care 32bit register. It is impossible to calculate it
from the resource size, since there is 16/32 bit register IP (e.g. VERSION
is located on 0xe2 if 16bit register, but it is located on 0x1c4 if 32bit
register).
This patch adds new TMIO_MMC_HAVE_HIGH_REG flags, tmio_mmc driver has it,
and sh_mobile_sdhi doesn't have it today.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
.bus_shift is used to 16/32bit register access offset calculation on
tmio driver. tmio_mmc_xxx is used from Toshiba/Renesas now, but this
bus_shift value depends on HW IP. This patch moves .bus_shift to
tmio_mmc_data member and sets it on each driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
All platforms pass the CD GPIO number to the driver in the .cd_gpio
field. The .get_cd() callback isn't used anymore, remove it
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This removes the deprecated use of the .private member of struct dma_chan
and switches the sdhi / tmio mmc driver to using the
dmaengine_slave_config() channel configuration method.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
So far only the SDHI implementation uses TMIO MMC with DMA. That way a DMA
channel filter function, defined in the TMIO driver wasn't a problem.
However, such a filter function is DMA controller specific. Since the SDHI
glue is only running on systems with the SHDMA DMA controller, the filter
function can safely be provided by it. Move it into SDHI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The tmio_mmc_cd_wakeup() inline function has been deprecated since 3.4 and
is unused since 3.4 too. Remove them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow tmio mmc glue drivers to pass mmc_host::caps2 flags down to
the mmc layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Every time the clock is enabled after possibly being disabled, we have
to re-read its frequency and update our configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The controller power status flag does not have to be accessed from the
hot-plug detection code any more, it can now be removed from the platform
data and put in the controller private struct.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the platform specifies the TMIO_MMC_HAS_COLD_CD flag, use the generic
MMC GPIO card hotplug helper.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers require waiting for the bus to become idle
before writing to some registers. I have implemented this
by adding a hook to sd_ctrl_write16() and implementing
a hook for SDHI which waits for the bus to become idle.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
The TMIO MMC controller cannot be powered off to save power, when no
card is plugged in, because then it will not be able to detect a new
card-insertion event. On some implementations, however, it is
possible to switch to using another source to detect card insertion.
This patch adds support for such implementations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch implements SDIO IRQ support for mfds which
announce the TMIO_MMC_SDIO_IRQ flag for tmio_mmc.
If MMC_CAP_SDIO_IRQ is also set SDIO IRQ signalling is activated.
Tested with a b43-based wireless SDIO card and sh_mobile_sdhi.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For example, with SDIO WLAN cards, some transfers happen with buffers at
odd addresses, whereas the SH-Mobile DMA engine requires even addresses
for SDHI. This patch extends the tmio driver with a bounce buffer, that
is used for single entry scatter-gather lists both for sending and
receiving. If we ever encounter unaligned transfers with multi-element
sg lists, this patch will have to be extended. For now it just falls
back to PIO in this and other unsupported cases.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Write-protection status is not always available, e.g., micro-SD cards do not
have a write-protection switch at all. This patch adds a flag to let platforms
force tmio_mmc to consider the card writable.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
After this patch, if the "dma" pointer in struct tmio_mmc_data is not NULL, it
points to a struct, containing two tokens, that have to be passed to the
dmaengine driver for channel configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove const from the tmio-mmc platform data hclk V3.
This change makes it possible to remove the type cast
from the sh_mobile_sdhi driver which is using the clock
framework to get the clock rate.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch abstracts out the CNF area code from tmio_mmc which
is not present in all hardware that can use this driver. This
is required so that we can support non-toshiba based hardware.
ASIC3 support by Philipp Zabel
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can not have .driver_data as const since platform_set_drvdata() doesnt take
a const.
The hclk mmc_data field can be const though.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Add driver for TMIO framebuffer cells as found e.g. in Toshiba TC6393XB
chips.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
