The Exynos4 SPI controller has migrated to the generic DMA bindings
since commit b5be04d35dbb("spi: s3c64xx: Modify SPI driver to use
generic DMA DT support"). Use the generic bindings to specify the
corresponding DMA to make the SPI usable again on Exynos4x12 SoCs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ISP power domain is a common power domain for FIMC-LITE
and FIMC-IS (camera ISP) devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pinctrl nodes for the ISP I2C0, ISP I2C1 and ISP UART devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add separate nodes for the CAMCLK pin and turn off pull-up on camera
ports A, B. The video bus pins and the clock output (CAMCLK) pin need
separate nodes since full camera port is not used in some configurations,
e.g. for MIPI CSI-2 bus only CAMCLK is required and data/clock signal
use separate dedicated pins.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds device node for TMU controller. There are 3
instances of the controllers so 3 nodes are created.
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Reviewed-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch introduces device tree sources for Samsung Trats 2 board
based on Exynos4412 SoC.
Currently support includes:
- eMMC,
- main PMIC (max77686),
- serial ports,
- GPIO keys,
- touchscreen.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The default audio module for the Arndale has a WM1811A on it. Add this to
the device tree bindings.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As part of this add nodes for the main wall supply as well as bucks 7
and 8 which are used to drop that down for several of the LDOs.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fixed voltage regulators (and other similar free standing things) are
supposed to go on a simple-bus for DT correctness reasons.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The out of tree code configures a pullup on the line indicating that it
is an active low interrupt.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real use
(and testing) out of the box on hardware.
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fKfy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Pull ARM fixes from Russell King:
"A few fixes for ARM, mostly just one liners with the exception of the
missing section specification. We decided not to rely on .previous to
fix this but to explicitly state the section we want the code to be
in."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7778/1: smp_twd: twd_update_frequency need be run on all online CPUs
ARM: 7782/1: Kconfig: Let ARM_ERRATA_364296 not depend on CONFIG_SMP
ARM: mm: fix boot on SA1110 Assabet
ARM: 7781/1: mmu: Add debug_ll_io_init() mappings to early mappings
ARM: 7780/1: add missing linker section markup to head-common.S
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
OMAP recently changed how the platforms are configured, so OMAP2/3/4 SoC
support is no longer enabled by default. Add them back.
Enable new ethernet driver for sunxi.
The i.MX console options moved due to resorting, no functional change.
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=qQ9Q
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij:
Ux500 defconfig changes:
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable HIGHMEM in the u8500 defconfig
ARM: ux500: Update MMC configs for u8500 defconfig
ARM: ux500: select SND_SOC_UX500 for ux500
ARM: ux500: update defconfig base
ARM: ux500: select WATCHDOG and MUSB for ux500
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add i.MX serial console support. This gives us the boot messages on
UART on e.g. the i.MX6Q sabre sd platform.
- Add the necessary config options, to allow booting with NFS root on
an i.MX6 sabre sd.
- Add Freescale LPUART serial console support. This gives us the boot
messages on UART on e.g. the Vybrid VF610 Tower board.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Russell King <linux@arm.linux.org.uk>
[olof: squashed three commits down to one]
Signed-off-by: Olof Johansson <olof@lixom.net>
get in before -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kO4u
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since all architectures have been converted to use vm_unmapped_area(),
there is no remaining use for the free_area_cache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- Add support for eMMC 5.1 devices.
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power management
of eMMC/SD between requests, using runtime PM.
- Add an ioctl to perform the eMMC 4.5 Sanitize command; sample code at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs.
- dw_mmc: Add support for Altera SoCFPGAs.
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable cards.
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs.
- sdhi/tmio: Add DT DMA support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=c/CM
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.11:
Core:
- Add support for eMMC 5.1 devices
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power
management of eMMC/SD between requests, using runtime PM
- Add an ioctl to perform the eMMC 4.5 Sanitize command. Sample code
at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs
- dw_mmc: Add support for Altera SoCFPGAs
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable
cards
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs
- sdhi/tmio: Add DT DMA support"
* tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (87 commits)
mmc: bcm281xx SDHCI driver
mmc: sdhci: add card_event callback to sdhci
mmc: core: Fixup Oops for SDIO shutdown
mmc: sdhci-pci: add another device id
mmc: esdhc: Fix bug when writing to SDHCI_HOST_CONTROL register
mmc: esdhc: Add support for 8-bit bus width and non-removable card
mmc: core: production year for eMMC 4.41 and later
mmc: omap: remove unnecessary #if 0's
mmc: sdhci: fix ctrl_2 on super-speed selection
mmc: dw_mmc-pltfm: add Rockchip variant
mmc: dw_mmc-pltfm: move probe and remove below dt match table
mmc: dw_mmc-pltfm: remove static from dw_mci_pltfm_remove
mmc: sdhci-acpi: add support for eMMC hardware reset for HID 80860F14
mmc: sdhci-pci: add support for eMMC hardware reset for BYT eMMC.
mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
mmc: sdhci: fix caps2 for HS200
sdhci-pxav3: Fix runtime PM initialization
mmc: core: Add DT-bindings for MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Invent MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Enable power_off_notify for eMMC shutdown sequence
...
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator subdevice
addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need since
commit 0998d063.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RqMp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For the 3.11 merge we only have one new MFD driver for the Kontron
PLD.
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich
driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator
subdevice addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need
since commit 0998d06310 ("device-core: Ensure drvdata = NULL when
no driver is bound")
* tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (102 commits)
mfd: sec: Provide max_register to regmap
mfd: wm8994: Remove duplicate check for active JACKDET
MAINTAINERS: Add include directory to MFD file patterns
mfd: sec: Remove fields not used since regmap conversion
watchdog: Kontron PLD watchdog timer driver
mfd: max8998: Add support for Device Tree
regulator: max8998: Use arrays for specifying voltages in platform data
mfd: max8998: Add irq domain support
regulator: palmas: Add TPS659038 support
mfd: Kontron PLD mfd driver
mfd: palmas: Add TPS659038 PMIC support
mfd: palmas: Add SMPS10_BOOST feature
mfd: palmas: Check if irq is valid
mfd: lpc_ich: iTCO_wdt patch for Intel Coleto Creek DeviceIDs
mfd: twl-core: Change TWL6025 references to TWL6032
mfd: davinci_voicecodec: Fix build breakage
mfd: vexpress: Make the driver optional for arm and arm64
mfd: htc-egpio: Use devm_ioremap_nocache() instead of ioremap_nocache()
mfd: davinci_voicecodec: Convert to use devm_* APIs
mfd: twl4030-power: Fix relocking on error
...
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
When the local timer freq changed, the twd_update_frequency function
should be run all the CPUs include itself, otherwise, the twd freq will
not get updated and the local timer will not run correcttly.
smp_call_function will run functions on all other CPUs, but not include
himself, this is not correct,use on_each_cpu instead to fix this issue.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
imx_v6_v7_defconfig handles both multi-core and single-core SoCs, and it has CONFIG_SMP=y selected by default.
With such config we cannot select ARM_ERRATA_364296, as it depends on !SMP.
Let ARM_ERRATA_364296 be undependent on CONFIG_SMP, so that we can select this erratum for the ARM1136 SoCs, even if CONFIG_SMP=y is enabled.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge together the unicore32, arm, and x86 reboot= command line
parameter handling.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for the moving the parsing of reboot= to the generic kernel code
by making reboot_mode into a more generic form.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These restart_mode fields are not used at all. Remove them to make
moving the reboot= cmdline options to the general kernel easier.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit bf0b8f4b55 ("hw_breakpoints: Fix racy access to
ptrace breakpoints").
The patch was fine but we can no longer race with SIGKILL after commit
9899d11f65 ("ptrace: ensure arch_ptrace/ptrace_request can never race
with SIGKILL"), the __TASK_TRACED tracee can't be woken up and
->ptrace_bps[] can't go away.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 83db0384 (mm/ARM: use common help functions to free reserved
pages) broke booting on the Assabet by trying to convert a PFN to
a virtual address using the __va() macro. This macro takes the
physical address, not a PFN. Fix this.
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Failure to add the mapping created in debug_ll_io_init() can lead
to the BUG_ON() triggering in lib/ioremap.c:27 if the static
virtual address decided for the debug_ll mapping overlaps with
another mapping that is created later. This happens because the
generic ioremap code has no idea there is a mapping there and it
tries to place a mapping in the same location and blows up when
it sees that there is a pte already present.
kernel BUG at lib/ioremap.c:27!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-rc2-00042-g2af0c67-dirty #316
task: ef088000 ti: ef082000 task.ti: ef082000
PC is at ioremap_page_range+0x16c/0x198
LR is at ioremap_page_range+0xf0/0x198
pc : [<c04cb874>] lr : [<c04cb7f8>] psr: 20000113
sp : ef083e78 ip : af140000 fp : ef083ebc
r10: ef7fc100 r9 : ef7fc104 r8 : 000af174
r7 : 00000647 r6 : beffffff r5 : f004c000 r4 : f0040000
r3 : af173417 r2 : 16440653 r1 : af173e07 r0 : ef7fc8fc
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 8020406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xef082238)
Stack: (0xef083e78 to 0xef084000)
3e60: 00040000 ef083eec
3e80: bf134000 f004bfff c0207c00 f004c000 c02fc120 f000c000 c15e7800 00040000
3ea0: ef083eec 00000647 c098ba9c c0953544 ef083edc ef083ec0 c021b82c c04cb714
3ec0: c09cdc50 00000040 ef0f1e00 ef1003c0 ef083f14 ef083ee0 c09535bc c021b7bc
3ee0: c0953544 c04d0c6c c094e2cc c1600be4 c07440c4 c09a6888 00000002 c0a15f00
3f00: ef082000 00000000 ef083f54 ef083f18 c0208728 c0953550 00000002 c1600bfc
3f20: c08e3fac c0839918 ef083f54 c1600b80 c09a6888 c0a15f00 0000008b c094e2cc
3f40: c098ba9c c098bab8 ef083f94 ef083f58 c094ea0c c020865c 00000002 00000002
3f60: c094e2cc 00000000 c025b674 00000000 c06ff860 00000000 00000000 00000000
3f80: 00000000 00000000 ef083fac ef083f98 c06ff878 c094e910 00000000 00000000
3fa0: 00000000 ef083fb0 c020efe8 c06ff86c 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 c0595108
[<c04cb874>] (ioremap_page_range+0x16c/0x198) from [<c021b82c>] (__alloc_remap_buffer.isra.18+0x7c/0xc4)
[<c021b82c>] (__alloc_remap_buffer.isra.18+0x7c/0xc4) from [<c09535bc>] (atomic_pool_init+0x78/0x128)
[<c09535bc>] (atomic_pool_init+0x78/0x128) from [<c0208728>] (do_one_initcall+0xd8/0x198)
[<c0208728>] (do_one_initcall+0xd8/0x198) from [<c094ea0c>] (kernel_init_freeable+0x108/0x1d0)
[<c094ea0c>] (kernel_init_freeable+0x108/0x1d0) from [<c06ff878>] (kernel_init+0x18/0xf4)
[<c06ff878>] (kernel_init+0x18/0xf4) from [<c020efe8>] (ret_from_fork+0x14/0x20)
Code: e50b0040 ebf54b2f e51b0040 eaffffee (e7f001f2)
Fix it by telling generic layers about the static mapping via
iotable_init(). This also has the nice side effect of letting
you see the mapping in procfs' vmallocinfo file.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Macro __INIT is used to place various code in head-common.S into the init
section. This should be matched by a closing __FINIT. Also, add an
explicit ".text" to ensure subsequent code is placed into the correct
section; __FINIT is simply a closing marker to match __INIT and doesn't
guarantee to revert to .text.
This historically caused no problem, because macro __CPUINIT was used at
the exact location where __FINIT was missing, which then placed following
code into the cpuinit section. However, with commit 22f0a2736 "init.h:
remove __cpuinit sections from the kernel" applied, __CPUINIT becomes a
no-op, thus leaving all this code in the init section, rather than the
regular text section. This caused issues such as secondary CPU boot
failures or crashes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"ARM: OMAP: build mach-omap code only if needed" moved around the
ARCH_OMAP2PLUS stanza, but accidentally dropped the seleciton of
TI_PRIV_EDMA in the process. Add it back.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull slave-dmaengine updates from Vinod Koul:
"Once you have some time from extended weekend celebrations please
consider pulling the following to get:
- Various fixes and PCI driver for dw_dmac by Andy
- DT binding for imx-dma by Markus & imx-sdma by Shawn
- DT fixes for dmaengine by Lars
- jz4740 dmac driver by Lars
- and various fixes across the drivers"
What "extended weekend celebrations"? I'm in the merge window, who has
time for extended celebrations..
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
DMA: shdma: add DT support
DMA: shdma: shdma_chan_filter() has to be in shdma-base.h
DMA: shdma: (cosmetic) don't re-calculate a pointer
dmaengine: at_hdmac: prepare clk before calling enable
dmaengine/trivial: at_hdmac: add curly brackets to if/else expressions
dmaengine: at_hdmac: remove unsuded atc_cleanup_descriptors()
dmaengine: at_hdmac: add FIFO configuration parameter to DMA DT binding
ARM: at91: dt: add header to define at_hdmac configuration
MIPS: jz4740: Correct clock gate bit for DMA controller
MIPS: jz4740: Remove custom DMA API
MIPS: jz4740: Register jz4740 DMA device
dma: Add a jz4740 dmaengine driver
MIPS: jz4740: Acquire and enable DMA controller clock
dma: mmp_tdma: disable irq when disabling dma channel
dmaengine: PL08x: Avoid collisions with get_signal() macro
dmaengine: dw: select DW_DMAC_BIG_ENDIAN_IO automagically
dma: dw: add PCI part of the driver
dma: dw: split driver to library part and platform code
dma: move dw_dmac driver to an own directory
dw_dmac: don't check resource with devm_ioremap_resource
...
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
Pull ARM DMA mapping updates from Marek Szyprowski:
"This contains important bugfixes and an update for IOMMU integration
support for ARM architecture"
* 'for-v3.11' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma: Drop __GFP_COMP for iommu dma memory allocations
ARM: DMA-mapping: mark all !DMA_TO_DEVICE pages in unmapping as clean
ARM: dma-mapping: NULLify dev->archdata.mapping pointer on detach
ARM: dma-mapping: convert DMA direction into IOMMU protection attributes
ARM: dma-mapping: Get pages if the cpu_addr is out of atomic_pool
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=XQbF
-----END PGP SIGNATURE-----
Merge tag 'xenarm-for-3.11-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen
Pull Xen ARM update rom Stefano Stabellini:
"Just one commit this time: the implementation of the tmem hypercall
for arm and arm64"
* tag 'xenarm-for-3.11-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen:
xen/arm and xen/arm64: implement HYPERVISOR_tmem_op
With the new linux/reboot.h header file dependency added, we can no
longer build ixp4xx. The easiest way to avoid that is to remove the
inclusion of mach/hardware.h from mach/timex.h, which does not need
that header anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Jason Cooper <jason@lakedaemon.net>
Some OMAP SoCs use this function while others do not, and that
causes a warning when building multi_v7_defconfig. Marking the
function __maybe_unused silences the harmless warning without the
need to add complex #ifdef logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
If we build a kernel with CONFIG_ARCH_OMAP2PLUS enabled but all of the
individual SoCs disabled, we run into a large number of link errors
because if incorrect dependencies:
arch/arm/mach-omap2/built-in.o: In function `_add_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:691: undefined reference to `clkdm_add_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_del_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:720: undefined reference to `clkdm_del_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_enable':
arch/arm/mach-omap2/omap_hwmod.c:2145: undefined reference to `clkdm_in_hwsup'
arch/arm/mach-omap2/omap_hwmod.c:2147: undefined reference to `clkdm_hwmod_enable'
arch/arm/mach-omap2/omap_hwmod.c:2191: undefined reference to `clkdm_hwmod_disable'
arch/arm/mach-omap2/omap_hwmod.c:2146: undefined reference to `clkdm_missing_idle_reporting' arch/arm/mach-omap2/built-in.o: In function `_idle':
arch/arm/mach-omap2/omap_hwmod.c:2235: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `_shutdown':
arch/arm/mach-omap2/omap_hwmod.c:2338: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `omap_hwmod_get_context_loss_count':
arch/arm/mach-omap2/omap_hwmod.c:4071: undefined reference to `pwrdm_get_context_loss_count' arch/arm/mach-omap2/built-in.o: In function `omap_pm_clkdms_setup':
arch/arm/mach-omap2/pm.c:114: undefined reference to `clkdm_allow_idle'
arch/arm/mach-omap2/pm.c:117: undefined reference to `clkdm_sleep' arch/arm/mach-omap2/built-in.o: In function `omap2_common_pm_late_init':
arch/arm/mach-omap2/pm.c:294: undefined reference to `omap_voltage_late_init' arch/arm/mach-omap2/built-in.o: In function `omap2_gpio_dev_init':
arch/arm/mach-omap2/gpio.c:133: undefined reference to `pwrdm_can_ever_lose_context'
We can avoid this if we make CONFIG_ARCH_OMAP2PLUS a silent option that
gets enabled any time that one of the SoC versions is enabled.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The zynq platform code only supports DT based booting, so we
should use DT_MACHINE_START rather than MACHINE_START.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Simek <michal.simek@xilinx.com>
These are selected by omap4 but used in common omap4/5
SMP code, so building an omap5-only kernel is actually
broken without this patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
