board-rx51 has no card detect pin in the mmc slot, but can detect that
the (cell-phone) cover has been removed and the card is accessible.
The semantics between cover/card detect differ, the gpio on the slot
informs you after the card has been removed, cover removal does not
necessarily mean that the card has been removed.
This means different code paths are necessary. To complete this we
also want different fields in the platform data for cover and card
detect. This separation is not pushed all the way down into struct
omap2_hsmmc_info which is used to initialize the platform data.
If we did that we had to go over all board files and set the new
gpio_cod pin to -EINVAL. If we forget one board or some out-of-tree
archicture forgets that the default '0' is used which is a valid pin
number.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->enable|disable() callbacks are only used to get and put runtime
PM references. Currently omap_hsmmc's ->set_ios() already does this
itself.
Other host drivers deals with runtime PM without using the
->enable|disable() callbacks and thus do the runtime PM reference
counting themselves. Apply that approach for omap_hsmmc as well and
then discard the ->enable|disable() callbacks.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some versions of this controller do not advertise their 3.0v and
8bit bus-width support capabilities. It is required to explicitly
set these capabilities for the specific controller versions.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the __raw IO functions to endian agnostic relaxed ones to allow
the driver to function on big endian ARM systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the sunxi mmc-controller code was initially merged MMC_CAP_SDIO_IRQ was
not added to the host caps because of issues with some sdio wifi modules.
It turns out that these issues have nothing to do with using sdio-irq support,
they also happen with oob interrupts. Since the hardware supports sdio-irq
everywhere, and since the one reason to not claim the capability is gone,
add MMC_CAP_SDIO_IRQ to the default host caps.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver co-allocates sdhci_iproc_host with sdhci_pltfm_host and so to
access it we need to use sdhci_pltfm_priv() and not pltfm_host->priv.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_request function should consider a non-removable device
always present.
Call the correct logic already available in sdhci_do_get_cd function.
This fixes some logic paths where MMC requests are being made to
non-removable devices that do not have the card detect pin connected
on the hardware as it is non-removable.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the member for card_int_gpio into the struct spear_sdhci.
In this way we eliminate the last user of the struct sdhci_plat_data,
which enables us to remove the exported header for sdhci-spear.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is used on SoCs which are using CONFIG_OF. By adding a
compile dependency in the Kconfig, it enables us to simplify some code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since there no users of the struct sdhci_host, but the shdci host
drivers themselves, let's move the definition of it to the local sdhci
header.
The exported sdhci header then becomes empty, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit cd1e65044d ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So
we don't need to do the check again in the platform device driver.
And the check in the current code is useless even if we really
run into a disabled device. In this case, it just doesn't parse
the dtb for the infos such as quirks or clock, but it will continue
to try to init the disabled device after that check. So just remove it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setup a different set of sdhci_ops for tegra114 and later so that
the write_w callback is only used on tegra114. This allows us to
remove the NVQUIRK_SHADOW_XFER_MODE_REG and simply the logic
in tegra_sdhci_writew.
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A command end interrupt should not be processed between command issue
and setting of wait_for flag. It expects already the flag to be set.
Therefore the exclusive control was added.
Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If interruption of command already occurred, mrq pointer in dev_err()
would refer to NULL, because the host-state is changed to STATE_IDLE
and mrq pointer is changed to NULL by interrupt handler.
Therefore dev_err is moved after checking STATE_IDLE.
Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was brought to my attention that the sdhci-pxav3 driver is needed
on a few more ARM machines than I initially thought. Add the missing
architectures to the dependency list.
Credits to Peter Robinson for noticing my mistake and reporting.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sunxi mmc driver tries to calculate a dma address by using pointer
arithmetic, which causes a warning when dma_addr_t is wider than a pointer:
drivers/mmc/host/sunxi-mmc.c: In function 'sunxi_mmc_init_idma_des':
drivers/mmc/host/sunxi-mmc.c:296:35: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
struct sunxi_idma_des *pdes_pa = (struct sunxi_idma_des *)host->sg_dma;
^
To avoid this warning and to simplify the logic, this changes
the code to avoid the cast and calculate the correct address
manually. The behavior should be unchanged.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For CMD53 in block mode, the host does not need to stop the transfer,
as it stops when the block count (present in CMD53) is reached.
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to handle broken auto-CMD23.
Some controllers do not respond after the first auto-CMD23 is issued.
This allows CMD23 to still work (mandatory for the faster UHS-I mode)
rather than disabling CMD23 entirely via SDHCI_QUIRK2_HOST_NO_CMD23.
Signed-off by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Static checkers suggest that probably we intended to put curly braces
around the writel() to make it part of the else path. But, I think
actually the indenting is off and the code works fine as is.
The stray tab was introduced in 0322191e62 ('mmc: sdhci-esdhc-imx: add
sd3.0 SDR clock tuning support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SET_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
omap_hsmmc_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[Grygorii.Strashko@linaro.org: rebased on top of K4.0]
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mobile phones (some) have no card detect pin, but can detect if the
cover is removed. The purpose is the same; detect if card is being
added/removed, but the details differ.
When the cover is removed, it does not mean the card is gone. But it
might, since it is accessible now. It's like a warning. All the driver
does is to limit write access to the card, see protect_card flag.
In contrast, card detect notifies us after the fact, e.g.
card is gone, card is inserted. We can't take precautions, but we can
rely on those events, -- the card is really gone, or do scan the card.
To summarize there is not much code sharing between cover and card
detect, it only increases confusion. By splitting, both will be
simplified in a followup patch.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The indirection via omap_hsmmc_get_ro and omap_hsmmc_get_wp is
redundant. Also dropped setting gpio_wp to EINVAL since platform date
is read-only
Untested: no device with ro pin was available, but change is fairly
simple
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
addon to: 09108968b7b72b6083a3bfc8f8259a74ed57255e
mmc: omap_hsmmc: remove prepare/complete system suspend support
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The reset control for the sunxi mmc controller is optional. Some
newer platforms (sun6i, sun8i, sun9i) have it, while older ones
(sun4i, sun5i, sun7i) don't.
Use the properly stubbed _optional version so the driver does not
fail to compile when RESET_CONTROLLER=n.
This patch also adds a check for deferred probing on the reset
control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 3.16+
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In these drivers, the driver specific .remove function just a simple
wrapper of function sdhci_pltfm_unregister(). So remove these wrappers
and just set .remove to sdhci_pltfm_unregister().
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So we can avoid to sprinkle the clk_disable_unprepare() in many
drivers.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Actually we can use the "clk" in the struct sdhci_pltfm_host. Also
change the "external clock" to "core clock" and kill two redundant
private functions in this driver as suggested by Ray Jui.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Actually we can use the "clk" in the struct sdhci_pltfm_host.
With this change we can also kill the private function for get
max clock in this driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is only one "clk" member in this driver specific private struct.
Actually we can use the "clk" member in the struct sdhci_pltfm_host,
and then kill this struct completely.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function clk_disable_unprepare() already take care of either error
or null cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the original tuning code, delay value is set to SD Bus Clock Delay
Register (SD_CLK_DELAY_SETTING) as (val | (Val << 7) | (val << 16)),
which means CLK_DELAY_IN1, CLK_DELAY_IN2 and CLK_DELAY_OUT are the
same and with 128 steps. This is doubtful. In CSR design specification
documents CS-304575-DR-3H, this issue is clarified, the delay[13:0] in
SD_CLK_DELAY_SETTING is simplied to the concatenation of {CLK_DELAY_IN2,
CLK_DELAY_IN1}.
Besides, for CMD19 tuning, no need to set CLK_DELAY_OUT([22,16]
of SD_CLK_DELAY_SETTING).
Signed-off-by: weijun yang <york.yang@csr.com>
Signed-off-by: Barry Song <baohua.song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We really don't want to get a card detect interrupt during probe time
since it can confuse things. Let's disable the card detect interrupt
until we're in a really good place: the end of probe. Let's also
simply avoid enabling the card detect interrupt if it's not used.
It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt. That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host(). On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children. I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:
Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host
Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.
The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.
We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command. This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.
Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should give dw_mmc a good reset after we apply power. On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.
Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It appears that we can confuse things if we try to turn on the MMC
clock when the power is off. Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command can terminate a data transfer between a memory card and
mmc controller.
As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.
After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support HS200 and UHS mode, mmc core will call init_card() to
execute tuning:
- sdio: init_card can be executed at runtime resume.
- sd and mmc: init_card can be executed at resume or runtime resume,
which depends on MMC_CAP_RUNTIME_RESUME capability.
On rk3288 SoC, host will get DRTO interrupt when host send command
to read tuning data. This will spend more than 111ms:
drto_ms = drto_clks * 1000 / bus_hz = 111ms.
And the total tuning time will be more than 400ms.
So we should add MMC_CAP_RUNTIME_RESUME capability to execute tuning
at runtime resume. Only if we do so, can we pass resume test.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
This change addresses following problem:
[ 2.560726] ------------[ cut here ]------------
[ 2.565341] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xec/0x118()
[ 2.574439] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 2.579821] Modules linked in:
[ 2.583038] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.18.0-next-20141216-00002-g4ff197fc1902-dirty #1318
[ 2.593796] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 2.599892] [<c0014c44>] (unwind_backtrace) from [<c0011bbc>] (show_stack+0x10/0x14)
[ 2.607612] [<c0011bbc>] (show_stack) from [<c04953b8>] (dump_stack+0x70/0xbc)
[ 2.614822] [<c04953b8>] (dump_stack) from [<c0023444>] (warn_slowpath_common+0x74/0xb0)
[ 2.622885] [<c0023444>] (warn_slowpath_common) from [<c0023514>] (warn_slowpath_fmt+0x30/0x40)
[ 2.631569] [<c0023514>] (warn_slowpath_fmt) from [<c0063644>] (lockdep_trace_alloc+0xec/0x118)
[ 2.640246] [<c0063644>] (lockdep_trace_alloc) from [<c00df52c>] (__kmalloc+0x3c/0x1cc)
[ 2.648240] [<c00df52c>] (__kmalloc) from [<c0394970>] (clk_fetch_parent_index+0xb8/0xd4)
[ 2.656390] [<c0394970>] (clk_fetch_parent_index) from [<c0394a6c>] (clk_calc_new_rates+0xe0/0x1fc)
[ 2.665415] [<c0394a6c>] (clk_calc_new_rates) from [<c0394b40>] (clk_calc_new_rates+0x1b4/0x1fc)
[ 2.674181] [<c0394b40>] (clk_calc_new_rates) from [<c0395408>] (clk_set_rate+0x50/0xc8)
[ 2.682265] [<c0395408>] (clk_set_rate) from [<c0377708>] (sdhci_cmu_set_clock+0x68/0x16c)
[ 2.690503] [<c0377708>] (sdhci_cmu_set_clock) from [<c03735cc>] (sdhci_do_set_ios+0xf0/0x64c)
[ 2.699095] [<c03735cc>] (sdhci_do_set_ios) from [<c0373b48>] (sdhci_set_ios+0x20/0x2c)
[ 2.707080] [<c0373b48>] (sdhci_set_ios) from [<c035ddf0>] (mmc_power_up+0x118/0x1fc)
[ 2.714889] [<c035ddf0>] (mmc_power_up) from [<c035ecd0>] (mmc_start_host+0x44/0x6c)
[ 2.722615] [<c035ecd0>] (mmc_start_host) from [<c035fd60>] (mmc_add_host+0x58/0x7c)
[ 2.730341] [<c035fd60>] (mmc_add_host) from [<c037454c>] (sdhci_add_host+0x968/0xd94)
[ 2.738240] [<c037454c>] (sdhci_add_host) from [<c0377b60>] (sdhci_s3c_probe+0x354/0x52c)
[ 2.746406] [<c0377b60>] (sdhci_s3c_probe) from [<c0283b58>] (platform_drv_probe+0x48/0xa4)
[ 2.754733] [<c0283b58>] (platform_drv_probe) from [<c02824e8>] (driver_probe_device+0x13c/0x37c)
[ 2.763585] [<c02824e8>] (driver_probe_device) from [<c02827bc>] (__driver_attach+0x94/0x98)
[ 2.772003] [<c02827bc>] (__driver_attach) from [<c0280a60>] (bus_for_each_dev+0x54/0x88)
[ 2.780163] [<c0280a60>] (bus_for_each_dev) from [<c0281b48>] (bus_add_driver+0xe4/0x200)
[ 2.788322] [<c0281b48>] (bus_add_driver) from [<c0282dfc>] (driver_register+0x78/0xf4)
[ 2.796308] [<c0282dfc>] (driver_register) from [<c00089b0>] (do_one_initcall+0xac/0x1f0)
[ 2.804473] [<c00089b0>] (do_one_initcall) from [<c0673d94>] (kernel_init_freeable+0x10c/0x1d8)
[ 2.813153] [<c0673d94>] (kernel_init_freeable) from [<c0490058>] (kernel_init+0x28/0x108)
[ 2.821398] [<c0490058>] (kernel_init) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 2.828939] ---[ end trace 03cc00e539849d1f ]---
clk_set_rate() tries to take clk's prepare_lock mutex while being in atomic
context entered in sdhci_do_set_ios().
The solution is inspired by similar situation in sdhci_set_power() also called
from sdhci_do_set_ios():
spin_unlock_irq(&host->lock);
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
spin_lock_irq(&host->lock);
Note that since sdhci_s3c_set_clock() sets SDHCI_CLOCK_CARD_EN, proposed change
first resets this bit. It is reset anyway (by setting SDHCI_CLOCK_INT_EN bit
only) after call to clk_set_rate() in order to wait for the clock to stabilize
and is set again as soon as the clock becomes stable.
Signed-off-by: Paul Osmialowski <p.osmialowsk@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>