This properly implemented dynamic state adjustment by
using a working copy of the requested and current
power states.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This properly implemented dynamic state adjustment by
using a working copy of the requested and current
power states.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for cayman asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching (requires additional acpi support)
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: fold in tdp fix
v3: fix indentation
v4: fix 64 bit div
v5: attempt to fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Use a dedicated copy of the current power state since
we may have to adjust it on the fly.
v2: fix up redundant state sets
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When using UVD, the driver must switch to a special UVD power
state. In the CS ioctl, switch to the power state and schedule
work to change the power state back, when the work comes up,
check if uvd is still busy and if not, switch back to the user
state, otherwise, reschedule the work.
Note: We really need some better way to decide when to
switch out of the uvd power state. Switching power states
while playback is active make uvd angry.
V2: fix locking.
V3: switch from timer to delayed work
V4: check fence driver for UVD jobs, reduce timeout to
1 second and rearm timeout on activity
v5: rebase on new dpm tree
v6: rebase on interim uvd on demand changes
v7: fix UVD when DPM is disabled
v8: unify non-DPM and DPM UVD handling
v9: remove leftover idle work struct
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
This adds dpm support for trinity asics. This includes:
- clockgating
- powergating
- dynamic engine clock scaling
- dynamic voltage scaling
set radeon.dpm=1 to enable it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for sumo asics. This includes:
- clockgating
- powergating
- dynamic engine clock scaling
- dynamic voltage scaling
set radeon.dpm=1 to enable it.
v2: fix indention
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
This adds dpm support for rv7xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: reduce stack usage
v3: fix 64 bit div
v4: fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So it looks like for virtual hw cursors on QXL we need to inform
the "hw" device what the cursor hotspot parameters are. This
makes sense if you think the host has to draw the cursor and interpret
clicks from it. However the current modesetting interface doesn't support
passing the hotspot information from userspace.
This implements a new cursor ioctl, that takes the hotspot info as well,
userspace can try calling the new interface and if it gets -ENOSYS it means
its on an older kernel and can just fallback.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bits weren't cleared so resolution changes didn't work.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In certain senarios drm will initialize before i2c this means that i2c
slave devices like the nxp tda998x will fail to be probed. This patch
detects this condition then defers the probe of the slave device and
the tilcdc main driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
keeping checkpatch happy.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tilcdc has a number of limitations for the allowed sizes of
the various adjustable timing parameter. Some modes are outside
of these timings. This commit will prune modes that report timings
that will overflow the allowed sizes in the tilcdc.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When hooking up to an HDMI analyzer noticed some timings were
off by one. Referring to the hardware technical reference manual
for the lcd controller some of the timing registers use 0 to
represent 1. This patch addresses that issue.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adding support for max-pixelclock and max-width device tree
entries. As some devices that use the tilcdc hardware module
have restrictions on the allowed/tested values. Also update DT
bindings document to reflect new parameters.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
TI LCD controller version 2 has an extended eleventh
bit that enables horizontal resolutions greater than
1024 pixels to be specified (upto 2048). This patch
adds support for setting this bit on LCDC V2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At the larger resolutions, the g200e series sometimes struggles with
maintaining a proper output. Problems like flickering or black bands appearing
on screen can occur. In order to avoid this, limitations regarding resolutions
and bandwidth have been added for the different variations of the g200e series.
This code was ported from the old xorg mga driver.
Signed-off-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds dpm support for rv6xx asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching
Set radeon.dpm=1 to enable.
v2: remove duplicate line
v3: fix thermal interrupt check noticed by Jerome
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
This adds dpm support for rs780/rs880 asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic voltage scaling
set radeon.dpm=1 to enable it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds the common dpm (dynamic power management)
infrastructure:
- dpm callbacks
- dpm init/fini/suspend/resume
- dpm power state selection
No device specific code is enabled yet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Has a different dpm controller than r600.
v2: rebase on gpu reset changes
v3: rebase on get_xclk changes
v4: update rptr/wtpr callbacks
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dpm needs access to atombios data and command tables
for setup and calculation of a number of parameters.
v2: endian fix
v3: fix mc reg table bug
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
