When multiple multicast routers are present in a broadcast domain then
only one of them will be detectable via IGMP/MLD query snooping. The
multicast router with the lowest IP address will become the selected and
active querier while all other multicast routers will then refrain from
sending queries.
To detect such rather silent multicast routers, too, RFC4286
("Multicast Router Discovery") provides a standardized protocol to
detect multicast routers for multicast snooping switches.
This patch implements the necessary MRD Advertisement message parsing
and after successful processing adds such routers to the internal
multicast router list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next to snooping IGMP/MLD queries RFC4541, section 2.1.1.a) recommends
to snoop multicast router advertisements to detect multicast routers.
Multicast router advertisements are sent to an "all-snoopers"
multicast address. To be able to receive them reliably, we need to
join this group.
Otherwise other snooping switches might refrain from forwarding these
advertisements to us.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.
In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.
The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.
Fixes: 816a3bed95 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is the first batch of Netfilter fixes for your net tree:
1) Fix endless loop in nf_tables rules netlink dump, from Phil Sutter.
2) Reference counter leak in object from the error path, from Taehee Yoo.
3) Selective rule dump requires table and chain.
4) Fix DNAT with nft_flow_offload reverse route lookup, from wenxu.
5) Use GFP_KERNEL_ACCOUNT in vmalloc allocation from ebtables, from
Shakeel Butt.
6) Set ifindex from route to fix interaction with VRF slave device,
also from wenxu.
7) Use nfct_help() to check for conntrack helper, IPS_HELPER status
flag is only set from explicit helpers via -j CT, from Henry Yen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo reported forwarding issues inside the linux bridge,
if the enslaved interfaces use the fq qdisc.
Similar to commit 8203e2d844 ("net: clear skb->tstamp in
forwarding paths"), we need to clear the tstamp field in
the bridge forwarding path.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The [ip,ip6,arp]_tables use x_tables_info internally and the underlying
memory is already accounted to kmemcg. Do the same for ebtables. The
syzbot, by using setsockopt(EBT_SO_SET_ENTRIES), was able to OOM the
whole system from a restricted memcg, a potential DoS.
By accounting the ebt_table_info, the memory used for ebt_table_info can
be contained within the memcg of the allocating process. However the
lifetime of ebt_table_info is independent of the allocating process and
is tied to the network namespace. So, the oom-killer will not be able to
relieve the memory pressure due to ebt_table_info memory. The memory for
ebt_table_info is allocated through vmalloc. Currently vmalloc does not
handle the oom-killed allocating process correctly and one large
allocation can bypass memcg limit enforcement. So, with this patch,
at least the small allocations will be contained. For large allocations,
we need to fix vmalloc.
Reported-by: syzbot+7713f3aa67be76b1552c@syzkaller.appspotmail.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When adding / deleting VLANs to / from a bridge port, the bridge driver
first tries to propagate the information via switchdev and falls back to
the 8021q driver in case the underlying driver does not support
switchdev. This can result in a memory leak [1] when VXLAN and mlxsw
ports are enslaved to the bridge:
$ ip link set dev vxlan0 master br0
# No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev
# notification and the bridge driver adds the VLAN on 'vxlan0' via the
# 8021q driver
$ bridge vlan add vid 10 dev vxlan0 pvid untagged
# mlxsw port is enslaved to the bridge
$ ip link set dev swp1 master br0
# mlxsw processes the switchdev notification and the 8021q driver is
# skipped
$ bridge vlan del vid 10 dev vxlan0
This results in 'struct vlan_info' and 'struct vlan_vid_info' being
leaked, as they were allocated by the 8021q driver during VLAN addition,
but never freed as the 8021q driver was skipped during deletion.
Fix this by introducing a new VLAN private flag that indicates whether
the VLAN was added on the port by switchdev or the 8021q driver. If the
VLAN was added by the 8021q driver, then we make sure to delete it via
the 8021q driver as well.
[1]
unreferenced object 0xffff88822d20b1e8 (size 256):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s)
hex dump (first 32 bytes):
e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00 .B..............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<00000000e0178b02>] vlan_vid_add+0x661/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
unreferenced object 0xffff888227454308 (size 32):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s)
hex dump (first 32 bytes):
88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff .. -...... -....
81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<0000000018050631>] vlan_vid_add+0x3e6/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
Fixes: d70e42b22d ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling DNAT'ed packets on a bridge device, the neighbour cache entry
from lookup was used without checking its state. It means that a cache entry
in the NUD_STALE state will be used directly instead of entering the NUD_DELAY
state to confirm the reachability of the neighbor.
This problem becomes worse after commit 2724680bce ("neigh: Keep neighbour
cache entries if number of them is small enough."), since all neighbour cache
entries in the NUD_STALE state will be kept in the neighbour table as long as
the number of cache entries does not exceed the value specified in gc_thresh1.
This commit validates the state of a neighbour cache entry before using
the entry.
Signed-off-by: JianJhen Chen <kchen@synology.com>
Reviewed-by: JinLin Chen <jlchen@synology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the bridge netfilter (calling iptables hooks from bridge)
facility to use the extension infrastructure.
The bridge_nf specific hooks in skb clone and free paths are removed, they
have been replaced by the skb_ext hooks that do the same as the bridge nf
allocations hooks did.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pointer is going to be removed soon, so use the existing helpers in
more places to avoid noise when the removal happens.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
function br_multicast_toggle now always return 0,
so the variable 'err' is unneeded.
Also cleanup dead branch in br_changelink.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port device seeks approval of a potential new MAC address, make
sure that should the bridge device end up using this address, all
interested parties would agree with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is attached to a bridge, the address of the bridge in
question may change as well. Even if it would not change at this
point (because the current bridge address is lower), it might end up
changing later as a result of detach of another port, which can't be
vetoed.
Therefore issue NETDEV_PRE_CHANGEADDR regardless of whether the address
will be used at this point or not, and make sure all involved parties
would agree with the change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, bridge driver has extack argument available to
pass to switchdev. Therefore extend switchdev_port_obj_add() with this
argument, updating all callers, and passing the argument through to
switchdev_port_obj_notify().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink has been updated in the previous patch to have extack
available, and changelink RTNL op has had this argument since the time
extack was added. Propagate both through the bridge driver to eventually
reach br_switchdev_port_vlan_add(), where it will be used by subsequent
patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver unoffloads all FDB entries en bloc, it's inefficient to
send the switchdev notification one by one. Add a helper that unsets the
offload flag on FDB entries on a given bridge port and VLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge's default hash_max was 512 which is rather conservative, now that
we're using the generic rhashtable API which autoshrinks let's increase
it to 4096 and move it to a define in br_private.h.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the bridge multicast uses the generic rhashtable interface we
can drop the hash_elasticity option as that is already done for us and
it's hardcoded to a maximum of RHT_ELASTICITY (16 currently). Add a
warning about the obsolete option when the hash_elasticity is set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast code has been using a mix of RCU and RCU-bh flavors
sometimes in questionable way. Since we've moved to rhashtable just use
non-bh RCU everywhere. In addition this simplifies freeing of objects
and allows us to remove some unnecessary callback functions.
v3: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge multicast code currently uses a custom resizable hashtable
which predates the generic rhashtable interface. It has many
shortcomings compared and duplicates functionality that is presently
available via the generic rhashtable, so this patch removes the custom
rhashtable implementation in favor of the kernel's generic rhashtable.
The hash maximum is kept and the rhashtable's size is used to do a loose
check if it's reached in which case we revert to the old behaviour and
disable further bridge multicast processing. Also now we can support any
hash maximum, doesn't need to be a power of 2.
v3: add non-rcu br_mdb_get variant and use it where multicast_lock is
held to avoid RCU splat, drop hash_max function and just set it
directly
v2: handle when IGMP snooping is undefined, add br_mdb_init/uninit
placeholders
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function only works for the bridge device itself, but
subsequent patches will need to be able to query the PVID of a given
bridge port, so extend the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have at least one bool option, we can export all of the
supported bool options via optmask when dumping them.
v2: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new boolopt API to add an option which disables learning from
link-local packets. The default is kept as before and learning is
enabled. This is a simple map from a boolopt bit to a bridge private
flag that is tested before learning.
v2: pass NULL for extack via sysfs
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been adding many new bridge options, a big number of which are
boolean but still take up netlink attribute ids and waste space in the skb.
Recently we discussed learning from link-local packets[1] and decided
yet another new boolean option will be needed, thus introducing this API
to save some bridge nl space.
The API supports changing the value of multiple boolean options at once
via the br_boolopt_multi struct which has an optmask (which options to
set, bit per opt) and optval (options' new values). Future boolean
options will only be added to the br_boolopt_id enum and then will have
to be handled in br_boolopt_toggle/get. The API will automatically
add the ability to change and export them via netlink, sysfs can use the
single boolopt function versions to do the same. The behaviour with
failing/succeeding is the same as with normal netlink option changing.
If an option requires mapping to internal kernel flag or needs special
configuration to be enabled then it should be handled in
br_boolopt_toggle. It should also be able to retrieve an option's current
state via br_boolopt_get.
v2: WARN_ON() on unsupported option as that shouldn't be possible and
also will help catch people who add new options without handling
them for both set and get. Pass down extack so if an option desires
it could set it on error and be more user-friendly.
[1] https://www.spinics.net/lists/netdev/msg532698.html
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change added a null check on p->dev after p->dev was being
dereferenced by the ns_capable check on p->dev. It turns out that
neither the p->dev and p->br null checks are necessary, and can be
removed, which cleans up a static analyis warning.
As Nikolay Aleksandrov noted, these checks can be removed because:
"My reasoning of why it shouldn't be possible:
- On port add new_nbp() sets both p->dev and p->br before creating
kobj/sysfs
- On port del (trickier) del_nbp() calls kobject_del() before call_rcu()
to destroy the port which in turn calls sysfs_remove_dir() which uses
kernfs_remove() which deactivates (shouldn't be able to open new
files) and calls kernfs_drain() to drain current open/mmaped files in
the respective dir before continuing, thus making it impossible to
open a bridge port sysfs file with p->dev and p->br equal to NULL.
So I think it's safe to remove those checks altogether. It'd be nice to
get a second look over my reasoning as I might be missing something in
sysfs/kernfs call path."
Thanks to Nikolay Aleksandrov's suggestion to remove the check and
David Miller for sanity checking this.
Detected by CoverityScan, CID#751490 ("Dereference before null check")
Fixes: a5f3ea54f3 ("net: bridge: add support for raw sysfs port options")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow querying bridge port flags so that drivers capable of performing
VxLAN learning will update the bridge driver only if learning is enabled
on its bridge port corresponding to the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a use-after-free of the global vlan context on port vlan
destruction. When I added per-port vlan stats I missed the fact that the
global vlan context can be freed before the per-port vlan rcu callback.
There're a few different ways to deal with this, I've chosen to add a
new private flag that is set only when per-port stats are allocated so
we can directly check it on destruction without dereferencing the global
context at all. The new field in net_bridge_vlan uses a hole.
v2: cosmetic change, move the check to br_process_vlan_info where the
other checks are done
v3: add change log in the patch, add private (in-kernel only) flags in a
hole in net_bridge_vlan struct and use that instead of mixing
user-space flags with private flags
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
Reported-by: syzbot+04681da557a0e49a52e5@syzkaller.appspotmail.com
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes assumption than vlan_tci != 0 when tag is present.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently a check was added which prevents marking of routers with zero
source address, but for IPv6 that cannot happen as the relevant RFCs
actually forbid such packets:
RFC 2710 (MLDv1):
"To be valid, the Query message MUST
come from a link-local IPv6 Source Address, be at least 24 octets
long, and have a correct MLD checksum."
Same goes for RFC 3810.
And also it can be seen as a requirement in ipv6_mc_check_mld_query()
which is used by the bridge to validate the message before processing
it. Thus any queries with :: source address won't be processed anyway.
So just remove the check for zero IPv6 source address from the query
processing function.
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on RFC 4541, 2.1.1. IGMP Forwarding Rules
The switch supporting IGMP snooping must maintain a list of
multicast routers and the ports on which they are attached. This
list can be constructed in any combination of the following ways:
a) This list should be built by the snooping switch sending
Multicast Router Solicitation messages as described in IGMP
Multicast Router Discovery [MRDISC]. It may also snoop
Multicast Router Advertisement messages sent by and to other
nodes.
b) The arrival port for IGMP Queries (sent by multicast routers)
where the source address is not 0.0.0.0.
We should not add the port to router list when receives query with source
0.0.0.0.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
readability improvements for the formatted output, some LICENSES updates
including the addition of the ISC license, the removal of the unloved and
unmaintained 00-INDEX files, the deprecated APIs document from Kees, more
MM docs from Mike Rapoport, and the usual pile of typo fixes and
corrections.
-----BEGIN PGP SIGNATURE-----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=C0wt
-----END PGP SIGNATURE-----
Merge tag 'docs-4.20' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"This is a fairly typical cycle for documentation. There's some welcome
readability improvements for the formatted output, some LICENSES
updates including the addition of the ISC license, the removal of the
unloved and unmaintained 00-INDEX files, the deprecated APIs document
from Kees, more MM docs from Mike Rapoport, and the usual pile of typo
fixes and corrections"
* tag 'docs-4.20' of git://git.lwn.net/linux: (41 commits)
docs: Fix typos in histogram.rst
docs: Introduce deprecated APIs list
kernel-doc: fix declaration type determination
doc: fix a typo in adding-syscalls.rst
docs/admin-guide: memory-hotplug: remove table of contents
doc: printk-formats: Remove bogus kobject references for device nodes
Documentation: preempt-locking: Use better example
dm flakey: Document "error_writes" feature
docs/completion.txt: Fix a couple of punctuation nits
LICENSES: Add ISC license text
LICENSES: Add note to CDDL-1.0 license that it should not be used
docs/core-api: memory-hotplug: add some details about locking internals
docs/core-api: rename memory-hotplug-notifier to memory-hotplug
docs: improve readability for people with poorer eyesight
yama: clarify ptrace_scope=2 in Yama documentation
docs/vm: split memory hotplug notifier description to Documentation/core-api
docs: move memory hotplug description into admin-guide/mm
doc: Fix acronym "FEKEK" in ecryptfs
docs: fix some broken documentation references
iommu: Fix passthrough option documentation
...
This fixes a problem introduced by:
commit 2cde6acd49 ("netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock")
When using netconsole on a bond, __netpoll_cleanup can asynchronously
recurse multiple times, each __netpoll_free_async call can result in
more __netpoll_free_async's. This means there is now a race between
cleanup_work queues on multiple netpoll_info's on multiple devices and
the configuration of a new netpoll. For example if a netconsole is set
to enable 0, reconfigured, and enable 1 immediately, this netconsole
will likely not work.
Given the reason for __netpoll_free_async is it can be called when rtnl
is not locked, if it is locked, we should be able to execute
synchronously. It appears to be locked everywhere it's called from.
Generalize the design pattern from the teaming driver for current
callers of __netpoll_free_async.
CC: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After per-port vlan stats, vlan stats should be released
when fail to add vlan
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
CC: bridge@lists.linux-foundation.org
cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to have per-port vlan stats instead of the
default global stats. The option can be set only when there are no port
vlans in the bridge since we need to allocate the stats if it is set
when vlans are being added to ports (and respectively free them
when being deleted). Also bump RTNL_MAX_TYPE as the bridge is the
largest user of options. The current stats design allows us to add
these without any changes to the fast-path, it all comes down to
the per-vlan stats pointer which, if this option is enabled, will
be allocated for each port vlan instead of using the global bridge-wide
one.
CC: bridge@lists.linux-foundation.org
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update br_mdb_dump for strict data checking. If the flag is set,
the dump request is expected to have a br_port_msg struct as the
header. All elements of the struct are expected to be 0 and no
attributes can be appended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 13cefad2f2 ("net: bridge: convert and rename mcast disabled")
converted the 'multicast_disabled' field to an option bit named
'BROPT_MULTICAST_ENABLED'.
While the old field was implicitly initialized to 0, the new field is
not initialized, resulting in the bridge defaulting to multicast
disabled state and breaking existing applications.
Fix this by explicitly initializing the option.
Fixes: 13cefad2f2 ("net: bridge: convert and rename mcast disabled")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to explicitly zero is_sticky when creating a new fdb, otherwise
we might get a stale value for a new entry.
Fixes: 435f2e7cc0 ("net: bridge: add support for sticky fdb entries")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Further reduce the size of net_bridge with 8 bytes and reduce the number of
holes in it:
Before: holes: 5, sum holes: 15
After: holes: 3, sum holes: 7
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the last remaining bool option to a bit thus reducing the overall
net_bridge size further by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the neigh_suppress_enabled option to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the rest of the mcast options to bits. It also packs
the mcast options a little better by moving multicast_mld_version to an
existing hole, reducing the net_bridge size by 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert mcast disabled to an option bit and while doing so convert the
logic to check if multicast is enabled instead. That is make the logic
follow the option value - if it's set then mcast is enabled and vice versa.
This avoids a few confusing places where we inverted the value that's being
set to follow the mcast_disabled logic.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert group_addr_set internal bridge opt to a bit.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No functional change, convert of nf_call_[ip|ip6|arp]tables to bits.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge options have usually been added as separate fields all over the
net_bridge struct taking up space and ending up in different cache lines.
Let's move them to a single bitfield to save up space and speedup lookups.
This patch adds a simple API for option modifying and retrieving using
bitops and converts the first user of the API - the bridge vlan options
(vlan_enabled and vlan_stats_enabled).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have a mix of opening brackets on new lines and on the same
line, let's move them all on the same line.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some documentation files received recent changes and are
pointing to wrong places.
Those references can easily fixed with the help of a
script:
$ ./scripts/documentation-file-ref-check --fix
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
For starters, the bridge netfilter code registers operations that
are invoked any time nh_hook is called. Specifically, ip_sabotage_in
watches for nested calls for NF_INET_PRE_ROUTING when a bridge is in
the stack.
Packet wise, the bridge netfilter hook runs first. br_nf_pre_routing
allocates nf_bridge, sets in_prerouting to 1 and calls NF_HOOK for
NF_INET_PRE_ROUTING. It's finish function, br_nf_pre_routing_finish,
then resets in_prerouting flag to 0 and the packet continues up the
stack. The packet eventually makes it to the VRF driver and it invokes
nf_hook for NF_INET_PRE_ROUTING in case any rules have been added against
the vrf device.
Because of the registered operations the call to nf_hook causes
ip_sabotage_in to be invoked. That function sees the nf_bridge on the
skb and that in_prerouting is not set. Thinking it is an invalid nested
call it steals (drops) the packet.
Update ip_sabotage_in to recognize that the bridge or one of its upper
devices (e.g., vlan) can be enslaved to a VRF (L3 master device) and
allow the packet to go through the nf_hook a second time.
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Reported-by: D'Souza, Nelson <ndsouza@ciena.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support for entries which are "sticky", i.e. will not change their port
if they show up from a different one. A new ndm flag is introduced for that
purpose - NTF_STICKY. We allow to set it only to non-local entries.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The err is not modified after initalization, So remove it and make
it to be void function.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netfilter exposes standard hook priorities in case of ipv4, ipv6 and
arp but not in case of bridge.
This patch exposes the hook priority values of the bridge family (which are
different from the formerly mentioned) via uapi so that they can be used by
user-space applications just like the others.
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new port attribute - IFLA_BRPORT_BACKUP_PORT, which
allows to set a backup port to be used for known unicast traffic if the
port has gone carrier down. The backup pointer is rcu protected and set
only under RTNL, a counter is maintained so when deleting a port we know
how many other ports reference it as a backup and we remove it from all.
Also the pointer is in the first cache line which is hot at the time of
the check and thus in the common case we only add one more test.
The backup port will be used only for the non-flooding case since
it's a part of the bridge and the flooded packets will be forwarded to it
anyway. To remove the forwarding just send a 0/non-existing backup port.
This is used to avoid numerous scalability problems when using MLAG most
notably if we have thousands of fdbs one would need to change all of them
on port carrier going down which takes too long and causes a storm of fdb
notifications (and again when the port comes back up). In a Multi-chassis
Link Aggregation setup usually hosts are connected to two different
switches which act as a single logical switch. Those switches usually have
a control and backup link between them called peerlink which might be used
for communication in case a host loses connectivity to one of them.
We need a fast way to failover in case a host port goes down and currently
none of the solutions (like bond) cannot fulfill the requirements because
the participating ports are actually the "master" devices and must have the
same peerlink as their backup interface and at the same time all of them
must participate in the bridge device. As Roopa noted it's normal practice
in routing called fast re-route where a precalculated backup path is used
when the main one is down.
Another use case of this is with EVPN, having a single vxlan device which
is backup of every port. Due to the nature of master devices it's not
currently possible to use one device as a backup for many and still have
all of them participate in the bridge (which is master itself).
More detailed information about MLAG is available at the link below.
https://docs.cumulusnetworks.com/display/DOCS/Multi-Chassis+Link+Aggregation+-+MLAG
Further explanation and a diagram by Roopa:
Two switches acting in a MLAG pair are connected by the peerlink
interface which is a bridge port.
the config on one of the switches looks like the below. The other
switch also has a similar config.
eth0 is connected to one port on the server. And the server is
connected to both switches.
br0 -- team0---eth0
|
-- switch-peerlink
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new alternative store callback for port sysfs options
which takes a raw value (buf) and can use it directly. It is needed for the
backup port sysfs support since we have to pass the device by its name.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating various bridge objects in /sys/class/net/... make sure
that they belong to the container's owner instead of global root (if
they belong to a container/namespace).
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the nft_reject_br_send_v4_tcp_reset(), a ttl is set by the
nf_reject_iphdr_put(). so, below code is unnecessary.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Reject non-null terminated helper names from xt_CT, from Gao Feng.
2) Fix KASAN splat due to out-of-bound access from commit phase, from
Alexey Kodanev.
3) Missing conntrack hook registration on IPVS FTP helper, from Julian
Anastasov.
4) Incorrect skbuff allocation size in bridge nft_reject, from Taehee Yoo.
5) Fix inverted check on packet xmit to non-local addresses, also from
Julian.
6) Fix ebtables alignment compat problems, from Alin Nastac.
7) Hook mask checks are not correct in xt_set, from Serhey Popovych.
8) Fix timeout listing of element in ipsets, from Jozsef.
9) Cap maximum timeout value in ipset, also from Jozsef.
10) Don't allow family option for hash:mac sets, from Florent Fourcot.
11) Restrict ebtables to work with NFPROTO_BRIDGE targets only, this
Florian.
12) Another bug reported by KASAN in the rbtree set backend, from
Taehee Yoo.
13) Missing __IPS_MAX_BIT update doesn't include IPS_OFFLOAD_BIT.
From Gao Feng.
14) Missing initialization of match/target in ebtables, from Florian
Westphal.
15) Remove useless nft_dup.h file in include path, from C. Labbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of br_fdb_find() need to hold the hash lock, which
br_fdb_find_port() doesn't do. However, since br_fdb_find_port() is not
doing any actual FDB manipulation, the hash lock is not really needed at
all. So convert to br_fdb_find_rcu(), surrounded by rcu_read_lock() /
_unlock() pair.
The device pointer copied from inside the FDB entry is then kept alive
by the RTNL lock, which br_fdb_find_port() asserts.
Fixes: 4d4fd36126 ("net: bridge: Publish bridge accessor functions")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reports following splat:
BUG: KMSAN: uninit-value in ebt_stp_mt_check+0x24b/0x450
net/bridge/netfilter/ebt_stp.c:162
ebt_stp_mt_check+0x24b/0x450 net/bridge/netfilter/ebt_stp.c:162
xt_check_match+0x1438/0x1650 net/netfilter/x_tables.c:506
ebt_check_match net/bridge/netfilter/ebtables.c:372 [inline]
ebt_check_entry net/bridge/netfilter/ebtables.c:702 [inline]
The uninitialised access is
xt_mtchk_param->nft_compat
... which should be set to 0.
Fix it by zeroing the struct beforehand, same for tgchk.
ip(6)tables targetinfo uses c99-style initialiser, so no change
needed there.
Reported-by: syzbot+da4494182233c23a5fcf@syzkaller.appspotmail.com
Fixes: 55917a21d0 ("netfilter: x_tables: add context to know if extension runs from nft_compat")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
-----BEGIN PGP SIGNATURE-----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=10u6
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit updates from Paul Moore:
"Another reasonable chunk of audit changes for v4.18, thirteen patches
in total.
The thirteen patches can mostly be broken down into one of four
categories: general bug fixes, accessor functions for audit state
stored in the task_struct, negative filter matches on executable
names, and extending the (relatively) new seccomp logging knobs to the
audit subsystem.
The main driver for the accessor functions from Richard are the
changes we're working on to associate audit events with containers,
but I think they have some standalone value too so I figured it would
be good to get them in now.
The seccomp/audit patches from Tyler apply the seccomp logging
improvements from a few releases ago to audit's seccomp logging;
starting with this patchset the changes in
/proc/sys/kernel/seccomp/actions_logged should apply to both the
standard kernel logging and audit.
As usual, everything passes the audit-testsuite and it happens to
merge cleanly with your tree"
[ Heh, except it had trivial merge conflicts with the SELinux tree that
also came in from Paul - Linus ]
* tag 'audit-pr-20180605' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: Fix wrong task in comparison of session ID
audit: use existing session info function
audit: normalize loginuid read access
audit: use new audit_context access funciton for seccomp_actions_logged
audit: use inline function to set audit context
audit: use inline function to get audit context
audit: convert sessionid unset to a macro
seccomp: Don't special case audited processes when logging
seccomp: Audit attempts to modify the actions_logged sysctl
seccomp: Configurable separator for the actions_logged string
seccomp: Separate read and write code for actions_logged sysctl
audit: allow not equal op for audit by executable
audit: add syscall information to FEATURE_CHANGE records
the ebtables evaluation loop expects targets to return
positive values (jumps), or negative values (absolute verdicts).
This is completely different from what xtables does.
In xtables, targets are expected to return the standard netfilter
verdicts, i.e. NF_DROP, NF_ACCEPT, etc.
ebtables will consider these as jumps.
Therefore reject any target found due to unspec fallback.
v2: also reject watchers. ebtables ignores their return value, so
a target that assumes skb ownership (and returns NF_STOLEN) causes
use-after-free.
The only watchers in the 'ebtables' front-end are log and nflog;
both have AF_BRIDGE specific wrappers on kernel side.
Reported-by: syzbot+2b43f681169a2a0d306a@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On arm64, ebt_entry_{match,watcher,target} structs are 40 bytes long
while on 32-bit arm these structs have a size of 36 bytes.
COMPAT_XT_ALIGN() macro cannot be used here to determine the necessary
padding for the CONFIG_COMPAT because it imposes an 8-byte boundary
alignment, condition that is not found in 32-bit ebtables application.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In order to allocate icmpv6 skb, sizeof(struct ipv6hdr) should be used.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver might need to react to changes in settings of brentry VLANs.
Therefore send switchdev port notifications for these as well. Reuse
SWITCHDEV_OBJ_ID_PORT_VLAN for this purpose. Listeners should use
netif_is_bridge_master() on orig_dev to determine whether the
notification is about a bridge port or a bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code that deals with adding a preexisting VLAN to bridge CPU
port to a separate function. A follow-up patch introduces a need to roll
back operations in this block due to an error, and this split will make
the error-handling code clearer.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to switchdev_port_obj_add() or switchdev_port_obj_del() involves
initializing a struct switchdev_obj_port_vlan, a piece of code that
repeats on each call site almost verbatim. While in the current codebase
there is just one duplicated add call, the follow-up patches add more of
both add and del calls.
Thus to remove the duplication, extract the repetition into named
functions and reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a new port flag - BR_ISOLATED. If it is set
then isolated ports cannot communicate between each other, but they can
still communicate with non-isolated ports. The same can be achieved via
ACLs but they can't scale with large number of ports and also the
complexity of the rules grows. This feature can be used to achieve
isolated vlan functionality (similar to pvlan) as well, though currently
it will be port-wide (for all vlans on the port). The new test in
should_deliver uses data that is already cache hot and the new boolean
is used to avoid an additional source port test in should_deliver.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recognizing that the audit context is an internal audit value, use an
access function to retrieve the audit context pointer for the task
rather than reaching directly into the task struct to get it.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
[PM: merge fuzz in auditsc.c and selinuxfs.c, checkpatch.pl fixes]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix handling of simultaneous open TCP connection in conntrack,
from Jozsef Kadlecsik.
2) Insufficient sanitify check of xtables extension names, from
Florian Westphal.
3) Skip unnecessary synchronize_rcu() call when transaction log
is already empty, from Florian Westphal.
4) Incorrect destination mac validation in ebt_stp, from Stephen
Hemminger.
5) xtables module reference counter leak in nft_compat, from
Florian Westphal.
6) Incorrect connection reference counting logic in IPVS
one-packet scheduler, from Julian Anastasov.
7) Wrong stats for 32-bits CPU in IPVS, also from Julian.
8) Calm down sparse error in netfilter core, also from Florian.
9) Use nla_strlcpy to fix compilation warning in nfnetlink_acct
and nfnetlink_cthelper, again from Florian.
10) Missing module alias in icmp and icmp6 xtables extensions,
from Florian Westphal.
11) Base chain statistics in nf_tables may be unset/null, from Florian.
12) Fix handling of large matchinfo size in nft_compat, this includes
one preparation for before this fix. From Florian.
13) Fix bogus EBUSY error when deleting chains due to incorrect reference
counting from the preparation phase of the two-phase commit protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mirroring offload in mlxsw needs to check that a given VLAN is allowed
to ingress the bridge device. br_vlan_get_info() is the function that is
used for this, however currently it only supports bridge port devices.
Extend it to support bridge masters as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination mac (destmac) is only valid if EBT_DESTMAC flag
is set. Fix by changing the order of the comparison to look for
the flag first.
Reported-by: syzbot+5c06e318fc558cc27823@syzkaller.appspotmail.com
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, more relevant updates in this batch are:
1) Add Maglev support to IPVS. Moreover, store lastest server weight in
IPVS since this is needed by maglev, patches from from Inju Song.
2) Preparation works to add iptables flowtable support, patches
from Felix Fietkau.
3) Hand over flows back to conntrack slow path in case of TCP RST/FIN
packet is seen via new teardown state, also from Felix.
4) Add support for extended netlink error reporting for nf_tables.
5) Support for larger timeouts that 23 days in nf_tables, patch from
Florian Westphal.
6) Always set an upper limit to dynamic sets, also from Florian.
7) Allow number generator to make map lookups, from Laura Garcia.
8) Use hash_32() instead of opencode hashing in IPVS, from Vicent Bernat.
9) Extend ip6tables SRH match to support previous, next and last SID,
from Ahmed Abdelsalam.
10) Move Passive OS fingerprint nf_osf.c, from Fernando Fernandez.
11) Expose nf_conntrack_max through ctnetlink, from Florent Fourcot.
12) Several housekeeping patches for xt_NFLOG, x_tables and ebtables,
from Taehee Yoo.
13) Unify meta bridge with core nft_meta, then make nft_meta built-in.
Make rt and exthdr built-in too, again from Florian.
14) Missing initialization of tbl->entries in IPVS, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not automatically bail out on sending notifications about activity on
non-user-added FDB entries. Instead, notify about this activity except
for cases where the activity itself originates in a notification, to
avoid sending duplicate notifications.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch enables sending notifications also for events on FDB
entries that weren't added by the user. Give the drivers the information
necessary to distinguish between the two origins of FDB entries.
To maintain the current behavior, have switchdev-implementing drivers
bail out on notifications about non-user-added FDB entries. In case of
mlxsw driver, allow a call to mlxsw_sp_span_respin() so that SPAN over
bridge catches up with the changed FDB.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While handling netdevice events, br_device_event() sometimes uses
br_stp_(disable|enable)_port which unconditionally send a notification,
but then a second notification for the same event is sent at the end of
the br_device_event() function. To avoid sending duplicate notifications
in such cases, check if one has already been sent (i.e.
br_stp_enable/disable_port have been called).
The patch is based on a change by Satish Ashok.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple new functions to allow querying FDB and vlan settings of a
bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we set a bond slave's master to bridge via ioctl, we only check
the IFF_BRIDGE_PORT flag. Although we will find the slave's real master
at netdev_master_upper_dev_link() later, it already does some settings
and allocates some resources. It would be better to return as early
as possible.
v1 -> v2:
use netdev_master_upper_dev_get() instead of netdev_has_any_upper_dev()
to check if we have a master, because not all upper devs are masters,
e.g. vlan device.
Reported-by: syzbot+de73361ee4971b6e6f75@syzkaller.appspotmail.com
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hlist_entry_safe() instead of open-coding it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It overcomplicates things for no reason.
nft_meta_bridge only offers retrieval of bridge port interface name.
Because of this being its own module, we had to export all nft_meta
functions, which we can then make static again (which even reduces
the size of nft_meta -- including bridge port retrieval...):
before:
text data bss dec hex filename
1838 832 0 2670 a6e net/bridge/netfilter/nft_meta_bridge.ko
6147 936 1 7084 1bac net/netfilter/nft_meta.ko
after:
5826 936 1 6763 1a6b net/netfilter/nft_meta.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebt_get_target similar to {ip/ip6/arp}t_get_target.
and ebt_get_target_c similar to {ip/ip6/arp}t_get_target_c.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
EBT_MATCH and EBT_NOMATCH are used to change return value.
match functions(ebt_xxx.c) return false when received frame is not matched
and returns true when received frame is matched.
but, EBT_MATCH_ITERATE understands oppositely.
so, to change return value, EBT_MATCH and EBT_NOMATCH are used.
but, we can use operation '!' simply.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A ebt_free_table_info frees all of chainstacks.
It similar to xt_free_table_info. this inline function
reduces code line.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Dmitry reports 32bit ebtables on 64bit kernel got broken by
a recent change that returns -EINVAL when ruleset has no entries.
ebtables however only counts user-defined chains, so for the
initial table nentries will be 0.
Don't try to allocate the compat array in this case, as no user
defined rules exist no rule will need 64bit translation.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 7d7d7e0211 ("netfilter: compat: reject huge allocation requests")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As Roopa noted today the biggest source of problems when configuring
bridge and ports is that the bridge MTU keeps changing automatically on
port events (add/del/changemtu). That leads to inconsistent behaviour
and network config software needs to chase the MTU and fix it on each
such event. Let's improve on that situation and allow for the user to
set any MTU within ETH_MIN/MAX limits, but once manually configured it
is the user's responsibility to keep it correct afterwards.
In case the MTU isn't manually set - the behaviour reverts to the
previous and the bridge follows the minimum MTU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the bridge was changed to automatically set maximum MTU on port
events (add/del/changemtu) when vlan filtering is enabled, but that
actually changes behaviour in a way which breaks some setups and can lead
to packet drops. In order to still allow that maximum to be set while being
compatible, we add the ability for the user to tune the bridge MTU up to
the maximum when vlan filtering is enabled, but that has to be done
explicitly and all port events (add/del/changemtu) lead to resetting that
MTU to the minimum as before.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. This batch comes with more input sanitization for xtables to
address bug reports from fuzzers, preparation works to the flowtable
infrastructure and assorted updates. In no particular order, they are:
1) Make sure userspace provides a valid standard target verdict, from
Florian Westphal.
2) Sanitize error target size, also from Florian.
3) Validate that last rule in basechain matches underflow/policy since
userspace assumes this when decoding the ruleset blob that comes
from the kernel, from Florian.
4) Consolidate hook entry checks through xt_check_table_hooks(),
patch from Florian.
5) Cap ruleset allocations at 512 mbytes, 134217728 rules and reject
very large compat offset arrays, so we have a reasonable upper limit
and fuzzers don't exercise the oom-killer. Patches from Florian.
6) Several WARN_ON checks on xtables mutex helper, from Florian.
7) xt_rateest now has a hashtable per net, from Cong Wang.
8) Consolidate counter allocation in xt_counters_alloc(), from Florian.
9) Earlier xt_table_unlock() call in {ip,ip6,arp,eb}tables, patch
from Xin Long.
10) Set FLOW_OFFLOAD_DIR_* to IP_CT_DIR_* definitions, patch from
Felix Fietkau.
11) Consolidate code through flow_offload_fill_dir(), also from Felix.
12) Inline ip6_dst_mtu_forward() just like ip_dst_mtu_maybe_forward()
to remove a dependency with flowtable and ipv6.ko, from Felix.
13) Cache mtu size in flow_offload_tuple object, this is safe for
forwarding as f87c10a8aa describes, from Felix.
14) Rename nf_flow_table.c to nf_flow_table_core.o, to simplify too
modular infrastructure, from Felix.
15) Add rt0, rt2 and rt4 IPv6 routing extension support, patch from
Ahmed Abdelsalam.
16) Remove unused parameter in nf_conncount_count(), from Yi-Hung Wei.
17) Support for counting only to nf_conncount infrastructure, patch
from Yi-Hung Wei.
18) Add strict NFT_CT_{SRC_IP,DST_IP,SRC_IP6,DST_IP6} key datatypes
to nft_ct.
19) Use boolean as return value from ipt_ah and from IPVS too, patch
from Gustavo A. R. Silva.
20) Remove useless parameters in nfnl_acct_overquota() and
nf_conntrack_broadcast_help(), from Taehee Yoo.
21) Use ipv6_addr_is_multicast() from xt_cluster, also from Taehee Yoo.
22) Statify nf_tables_obj_lookup_byhandle, patch from Fengguang Wu.
23) Fix typo in xt_limit, from Geert Uytterhoeven.
24) Do no use VLAs in Netfilter code, again from Gustavo.
25) Use ADD_COUNTER from ebtables, from Taehee Yoo.
26) Bitshift support for CONNMARK and MARK targets, from Jack Ma.
27) Use pr_*() and add pr_fmt(), from Arushi Singhal.
28) Add synproxy support to ctnetlink.
29) ICMP type and IGMP matching support for ebtables, patches from
Matthias Schiffer.
30) Support for the revision infrastructure to ebtables, from
Bernie Harris.
31) String match support for ebtables, also from Bernie.
32) Documentation for the new flowtable infrastructure.
33) Use generic comparison functions in ebt_stp, from Joe Perches.
34) Demodularize filter chains in nftables.
35) Register conntrack hooks in case nftables NAT chain is added.
36) Merge assignments with return in a couple of spots in the
Netfilter codebase, also from Arushi.
37) Document that xtables percpu counters are stored in the same
memory area, from Ben Hutchings.
38) Revert mark_source_chains() sanity checks that break existing
rulesets, from Florian Westphal.
39) Use is_zero_ether_addr() in the ipset codebase, from Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
One module per supported filter chain family type takes too much memory
for very little code - too much modularization - place all chain filter
definitions in one single file.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use WARN_ON() instead since it should not happen that neither family
goes over NFPROTO_NUMPROTO nor there is already a chain of this type
already registered.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use nft_ prefix. By when I added chain types, I forgot to use the
nftables prefix. Rename enum nft_chain_type to enum nft_chain_types too,
otherwise there is an overlap.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of unnecessary const declarations, use the generic functions to
save a little object space.
$ size net/bridge/netfilter/ebt_stp.o*
text data bss dec hex filename
1250 144 0 1394 572 net/bridge/netfilter/ebt_stp.o.new
1344 144 0 1488 5d0 net/bridge/netfilter/ebt_stp.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently ebtables assumes that the revision number of all match
modules is 0, which is an issue when trying to use existing
xtables matches with ebtables. The solution is to modify ebtables
to allow extensions to specify a revision number, similar to
iptables. This gets passed down to the kernel, which is then able
to find the match module correctly.
To main binary backwards compatibility, the size of the ebt_entry
structures is not changed, only the size of the name field is
decreased by 1 byte to make room for the revision field.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use br_vlan_enabled() helper otherwise we'll break builds
without bridge vlans:
net/bridge//br_if.c: In function ‘br_mtu’:
net/bridge//br_if.c:458:8: error: ‘const struct net_bridge’ has no
member named ‘vlan_enabled’
if (br->vlan_enabled)
^
net/bridge//br_if.c:462:1: warning: control reaches end of non-void
function [-Wreturn-type]
}
^
scripts/Makefile.build:324: recipe for target 'net/bridge//br_if.o'
failed
Fixes: 419d14af9e ("bridge: Allow max MTU when multiple VLANs present")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bridge is allowing multiple VLANs, some VLANs may have
different MTUs. Instead of choosing the minimum MTU for the
bridge interface, choose the maximum MTU of the bridge members.
With this the user only needs to set a larger MTU on the member
ports that are participating in the large MTU VLANS.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have ICMPv6 type/code matches (which can be used to distinguish
different types of MLD packets). Add support for IPv4 IGMP matches in the
same way.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We already have ICMPv6 type/code matches. This adds support for IPv4 ICMP
matches in the same way.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xtables uses ADD_COUNTER macro to increase
packet and byte count. ebtables also can use this.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
commit c4585a2823 ("bridge: ebt_among: add missing match size checks")
added validation for pool size, but missed fact that the macros
ebt_among_wh_src/dst can already return out-of-bound result because
they do not check value of wh_src/dst_ofs (an offset) vs. the size
of the match that userspace gave to us.
v2:
check that offset has correct alignment.
Paolo Abeni points out that we should also check that src/dst
wormhash arrays do not overlap, and src + length lines up with
start of dst (or vice versa).
v3: compact wormhash_sizes_valid() part
NB: Fixes tag is intentionally wrong, this bug exists from day
one when match was added for 2.6 kernel. Tag is there so stable
maintainers will notice this one too.
Tested with same rules from the earlier patch.
Fixes: c4585a2823 ("bridge: ebt_among: add missing match size checks")
Reported-by: <syzbot+bdabab6f1983a03fc009@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.
Fixes: b718121685 ("netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
should have no impact, function still always returns 0.
This patch is only to ease review.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
These pernet_operations use nf_log_set() and nf_log_unset()
in their methods:
nf_log_bridge_net_ops
nf_log_arp_net_ops
nf_log_ipv4_net_ops
nf_log_ipv6_net_ops
nf_log_netdev_net_ops
Nobody can send such a packet to a net before it's became
registered, nobody can send a packet after all netdevices
are unregistered. So, these pernet_operations are able
to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations use ebt_register_table() and
ebt_unregister_table() to act on the tables, which
are used as argument in ebt_do_table(), called from
ebtables hooks.
Since there are no net-related bridge packets in-flight,
when the init and exit methods are called, these
pernet_operations are safe to be executed in parallel
with any other.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Put back reference on CLUSTERIP configuration structure from the
error path, patch from Florian Westphal.
2) Put reference on CLUSTERIP configuration instead of freeing it,
another cpu may still be walking over it, also from Florian.
3) Refetch pointer to IPv6 header from nf_nat_ipv6_manip_pkt() given
packet manipulation may reallocation the skbuff header, from Florian.
4) Missing match size sanity checks in ebt_among, from Florian.
5) Convert BUG_ON to WARN_ON in ebtables, from Florian.
6) Sanity check userspace offsets from ebtables kernel, from Florian.
7) Missing checksum replace call in flowtable IPv4 DNAT, from Felix
Fietkau.
8) Bump the right stats on checksum error from bridge netfilter,
from Taehee Yoo.
9) Unset interface flag in IPv6 fib lookups otherwise we get
misleading routing lookup results, from Florian.
10) Missing sk_to_full_sk() in ip6_route_me_harder() from Eric Dumazet.
11) Don't allow devices to be part of multiple flowtables at the same
time, this may break setups.
12) Missing netlink attribute validation in flowtable deletion.
13) Wrong array index in nf_unregister_net_hook() call from error path
in flowtable addition path.
14) Fix FTP IPVS helper when NAT mangling is in place, patch from
Julian Anastasov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations only unregister nf hooks.
So, they are able to be marked as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net bridge devices, and it looks like another
pernet_operations are not interested in foreign net bridge list.
So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added on a port, a reference is taken on the
corresponding master VLAN entry. If it does not already exist, then it
is created and a reference taken.
However, in the second case a reference is not really taken when
CONFIG_REFCOUNT_FULL is enabled as refcount_inc() is replaced by
refcount_inc_not_zero().
Fix this by using refcount_set() on a newly created master VLAN entry.
Fixes: 2512775985 ("net, bridge: convert net_bridge_vlan.refcnt from atomic_t to refcount_t")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ip_rcv, IPSTATS_MIB_CSUMERRORS is increased when
checksum error is occurred.
bridge netfilter routine should increase IPSTATS_MIB_CSUMERRORS.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need to make sure the offsets are not out of range of the
total size.
Also check that they are in ascending order.
The WARN_ON triggered by syzkaller (it sets panic_on_warn) is
changed to also bail out, no point in continuing parsing.
Briefly tested with simple ruleset of
-A INPUT --limit 1/s' --log
plus jump to custom chains using 32bit ebtables binary.
Reported-by: <syzbot+845a53d13171abf8bf29@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All of these conditions are not fatal and should have
been WARN_ONs from the get-go.
Convert them to WARN_ONs and bail out.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
Therefore it must check that the size of the match structure
provided from userspace is sane by making sure em->match_size
is at least the minimum size of the expected structure.
The module has such a check, but its only done after accessing
a structure that might be out of bounds.
tested with: ebtables -A INPUT ... \
--among-dst fe:fe:fe:fe:fe:fe
--among-dst fe:fe:fe:fe:fe:fe --among-src fe:fe:fe:fe:ff:f,fe:fe:fe:fe:fe:fb,fe:fe:fe:fe:fc:fd,fe:fe:fe:fe:fe:fd,fe:fe:fe:fe:fe:fe
--among-src fe:fe:fe:fe:ff:f,fe:fe:fe:fe:fe:fa,fe:fe:fe:fe:fe:fd,fe:fe:fe:fe:fe:fe,fe:fe:fe:fe:fe:fe
Reported-by: <syzbot+fe0b19af568972814355@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains large batch with Netfilter fixes for
your net tree, mostly due to syzbot report fixups and pr_err()
ratelimiting, more specifically, they are:
1) Get rid of superfluous unnecessary check in x_tables before vmalloc(),
we don't hit BUG there anymore, patch from Michal Hock, suggested by
Andrew Morton.
2) Race condition in proc file creation in ipt_CLUSTERIP, from Cong Wang.
3) Drop socket lock that results in circular locking dependency, patch
from Paolo Abeni.
4) Drop packet if case of malformed blob that makes backpointer jump
in x_tables, from Florian Westphal.
5) Fix refcount leak due to race in ipt_CLUSTERIP in
clusterip_config_find_get(), from Cong Wang.
6) Several patches to ratelimit pr_err() for x_tables since this can be
a problem where CAP_NET_ADMIN semantics can protect us in untrusted
namespace, from Florian Westphal.
7) Missing .gitignore update for new autogenerated asn1 state machine
for the SNMP NAT helper, from Zhu Lingshan.
8) Missing timer initialization in xt_LED, from Paolo Abeni.
9) Do not allow negative port range in NAT, also from Paolo.
10) Lock imbalance in the xt_hashlimit rate match mode, patch from
Eric Dumazet.
11) Initialize workqueue before timer in the idletimer match,
from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ebt_among still uses pr_err -- these errors indicate ebtables tool bug,
not a usage error.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now br_sysfs_if file flush doesn't have attr show. To read it will
cause kernel panic after users chmod u+r this file.
Xiong found this issue when running the commands:
ip link add br0 type bridge
ip link add type veth
ip link set veth0 master br0
chmod u+r /sys/devices/virtual/net/veth0/brport/flush
timeout 3 cat /sys/devices/virtual/net/veth0/brport/flush
kernel crashed with NULL a pointer dereference call trace.
This patch is to fix it by return -EINVAL when brport_attr->show
is null, just the same as the check for brport_attr->store in
brport_store().
Fixes: 9cf637473c ("bridge: add sysfs hook to flush forwarding table")
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With gcc-4.1.2.:
net/bridge/br_fdb.c: In function ‘br_fdb_sync_static’:
net/bridge/br_fdb.c:996: warning: ‘err’ may be used uninitialized in this function
Indeed, if the list is empty, err will be uninitialized, and will be
propagated up as the function return value.
Fix this by preinitializing err to zero.
Fixes: eb7935830d ("net: bridge: use rhashtable for fdbs")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements in functions returning bool should use
true/false instead of 1/0.
This issue was detected with the help of Coccinelle.
Fixes: 85b3526932 ("bridge: Fix build error when IGMP_SNOOPING is not enabled")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several reasons for this:
* Several modules maintain internal version numbers, that they print at
boot/module load time, that are not exposed to userspace, as a
primitive mechanism to make revision number control from the earlier
days of Netfilter.
* IPset shows the protocol version at boot/module load time, instead
display this via module description, as Jozsef suggested.
* Remove copyright notice at boot/module load time in two spots, the
Netfilter codebase is a collective development effort, if we would
have to display copyrights for each contributor at boot/module load
time for each extensions we have, we would probably fill up logs with
lots of useless information - from a technical standpoint.
So let's be consistent and remove them all.
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Remove the infrastructure to register/unregister nft_af_info structure,
this structure stores no useful information anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that we have a single table list for each netns, we can get rid of
one pointer per family and the global afinfo list, thus, shrinking
struct netns for nftables that now becomes 64 bytes smaller.
And call __nft_release_afinfo() from __net_exit path accordingly to
release netnamespace objects on removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We already validate the hook through bitmask, so this check is
superfluous. When removing this, this patch is also fixing a bug in the
new flowtable codebase, since ctx->afi points to the table family
instead of the netdev family which is where the flowtable is really
hooked in.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This abstraction has no clients anymore, remove it.
This is what remains from previous authors, so correct copyright
statement after recent modifications and code removal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_reroute() because that would result
in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define reroute indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_route() because that would result
in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define route indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is only used by nf_queue.c and this function comes with no symbol
dependencies with IPv6, it just refers to structure layouts. Therefore,
we can replace it by a direct function call from where it belongs.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_checksum_partial() because that
would result in autoloading the 'ipv6' module because of symbol
dependencies. Therefore, define checksum_partial indirection in
nf_ipv6_ops where this really belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We cannot make a direct call to nf_ip6_checksum() because that would
result in autoloading the 'ipv6' module because of symbol dependencies.
Therefore, define checksum indirection in nf_ipv6_ops where this really
belongs to.
For IPv4, we can indeed make a direct function call, which is faster,
given IPv4 is built-in in the networking code by default. Still,
CONFIG_INET=n and CONFIG_NETFILTER=y is possible, so define empty inline
stub for IPv4 in such case.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
They don't belong to the family definition, move them to the filter
chain type definition instead.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since NFPROTO_INET is handled from the core, we don't need to maintain
extra infrastructure in nf_tables to handle the double hook
registration, one for IPv4 and another for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Instead of calling this function from the family specific variant, this
reduces the code size in the fast path for the netdev, bridge and inet
families. After this change, we must call nft_set_pktinfo() upfront from
the chain hook indirection.
Before:
text data bss dec hex filename
2145 208 0 2353 931 net/netfilter/nf_tables_netdev.o
After:
text data bss dec hex filename
2125 208 0 2333 91d net/netfilter/nf_tables_netdev.o
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
no need to define hook points if the family isn't supported.
Because we need these hooks for either nftables, arp/ebtables
or the 'call-iptables' hack we have in the bridge layer add two
new dependencies, NETFILTER_FAMILY_{ARP,BRIDGE}, and have the
users select them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
struct net contains:
struct nf_hook_entries __rcu *hooks[NFPROTO_NUMPROTO][NF_MAX_HOOKS];
which store the hook entry point locations for the various protocol
families and the hooks.
Using array results in compact c code when doing accesses, i.e.
x = rcu_dereference(net->nf.hooks[pf][hook]);
but its also wasting a lot of memory, as most families are
not used.
So split the array into those families that are used, which
are only 5 (instead of 13). In most cases, the 'pf' argument is
constant, i.e. gcc removes switch statement.
struct net before:
/* size: 5184, cachelines: 81, members: 46 */
after:
/* size: 4672, cachelines: 73, members: 46 */
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use
%pM to print MAC
mac_pton() to convert it from ASCII to binary format, and
ether_addr_copy() to copy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The early call to br_stp_change_bridge_id in bridge's newlink can cause
a memory leak if an error occurs during the newlink because the fdb
entries are not cleaned up if a different lladdr was specified, also
another minor issue is that it generates fdb notifications with
ifindex = 0. Another unrelated memory leak is the bridge sysfs entries
which get added on NETDEV_REGISTER event, but are not cleaned up in the
newlink error path. To remove this special case the call to
br_stp_change_bridge_id is done after netdev register and we cleanup the
bridge on changelink error via br_dev_delete to plug all leaks.
This patch makes netlink bridge destruction on newlink error the same as
dellink and ioctl del which is necessary since at that point we have a
fully initialized bridge device.
To reproduce the issue:
$ ip l add br0 address 00:11:22:33:44:55 type bridge group_fwd_mask 1
RTNETLINK answers: Invalid argument
$ rmmod bridge
[ 1822.142525] =============================================================================
[ 1822.143640] BUG bridge_fdb_cache (Tainted: G O ): Objects remaining in bridge_fdb_cache on __kmem_cache_shutdown()
[ 1822.144821] -----------------------------------------------------------------------------
[ 1822.145990] Disabling lock debugging due to kernel taint
[ 1822.146732] INFO: Slab 0x0000000092a844b2 objects=32 used=2 fp=0x00000000fef011b0 flags=0x1ffff8000000100
[ 1822.147700] CPU: 2 PID: 13584 Comm: rmmod Tainted: G B O 4.15.0-rc2+ #87
[ 1822.148578] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 1822.150008] Call Trace:
[ 1822.150510] dump_stack+0x78/0xa9
[ 1822.151156] slab_err+0xb1/0xd3
[ 1822.151834] ? __kmalloc+0x1bb/0x1ce
[ 1822.152546] __kmem_cache_shutdown+0x151/0x28b
[ 1822.153395] shutdown_cache+0x13/0x144
[ 1822.154126] kmem_cache_destroy+0x1c0/0x1fb
[ 1822.154669] SyS_delete_module+0x194/0x244
[ 1822.155199] ? trace_hardirqs_on_thunk+0x1a/0x1c
[ 1822.155773] entry_SYSCALL_64_fastpath+0x23/0x9a
[ 1822.156343] RIP: 0033:0x7f929bd38b17
[ 1822.156859] RSP: 002b:00007ffd160e9a98 EFLAGS: 00000202 ORIG_RAX: 00000000000000b0
[ 1822.157728] RAX: ffffffffffffffda RBX: 00005578316ba090 RCX: 00007f929bd38b17
[ 1822.158422] RDX: 00007f929bd9ec60 RSI: 0000000000000800 RDI: 00005578316ba0f0
[ 1822.159114] RBP: 0000000000000003 R08: 00007f929bff5f20 R09: 00007ffd160e8a11
[ 1822.159808] R10: 00007ffd160e9860 R11: 0000000000000202 R12: 00007ffd160e8a80
[ 1822.160513] R13: 0000000000000000 R14: 0000000000000000 R15: 00005578316ba090
[ 1822.161278] INFO: Object 0x000000007645de29 @offset=0
[ 1822.161666] INFO: Object 0x00000000d5df2ab5 @offset=128
Fixes: 30313a3d57 ("bridge: Handle IFLA_ADDRESS correctly when creating bridge device")
Fixes: 5b8d5429da ("bridge: netlink: register netdevice before executing changelink")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the bridge used a fixed 256 element hash table which
was fine for small use cases (in my tests it starts to degrade
above 1000 entries), but it wasn't enough for medium or large
scale deployments. Modern setups have thousands of participants in a
single bridge, even only enabling vlans and adding a few thousand vlan
entries will cause a few thousand fdbs to be automatically inserted per
participating port. So we need to scale the fdb table considerably to
cope with modern workloads, and this patch converts it to use a
rhashtable for its operations thus improving the bridge scalability.
Tests show the following results (10 runs each), at up to 1000 entries
rhashtable is ~3% slower, at 2000 rhashtable is 30% faster, at 3000 it
is 2 times faster and at 30000 it is 50 times faster.
Obviously this happens because of the properties of the two constructs
and is expected, rhashtable keeps pretty much a constant time even with
10000000 entries (tested), while the fixed hash table struggles
considerably even above 10000.
As a side effect this also reduces the net_bridge struct size from 3248
bytes to 1344 bytes. Also note that the key struct is 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
all of these can be compiled as a module, so use new
_module version to make sure module can no longer be removed
while callback/dump is in use.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first member of an IPSEC route bundle chain sets it's dst->path to
the underlying ipv4/ipv6 route that carries the bundle.
Stated another way, if one were to follow the xfrm_dst->child chain of
the bundle, the final non-NULL pointer would be the path and point to
either an ipv4 or an ipv6 route.
This is largely used to make sure that PMTU events propagate down to
the correct ipv4 or ipv6 route.
When we don't have the top of an IPSEC bundle 'dst->path == dst'.
Move it down into xfrm_dst and key off of dst->xfrm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Found another missing port flag policy entry for IFLA_BRPORT_VLAN_TUNNEL
so add it now.
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the host joins or leaves a multicast group, use switchdev to add
an object to the hardware to forward traffic for the group to the
host.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The host can join or leave a multicast group on the brX interface, as
indicated by IGMP snooping. This is tracked within the bridge
multicast code. Send a notification when this happens, in the same way
a notification is sent when a port of the bridge joins/leaves a group
because of IGMP snooping.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boolean mglist indicates the host has joined a particular
multicast group on the bridge interface. It is badly named, obscuring
what is means. Rename it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, they are:
1) Speed up table replacement on busy systems with large tables
(and many cores) in x_tables. Now xt_replace_table() synchronizes by
itself by waiting until all cpus had an even seqcount and we use no
use seqlock when fetching old counters, from Florian Westphal.
2) Add nf_l4proto_log_invalid() and nf_ct_l4proto_log_invalid() to speed
up packet processing in the fast path when logging is not enabled, from
Florian Westphal.
3) Precompute masked address from configuration plane in xt_connlimit,
from Florian.
4) Don't use explicit size for set selection if performance set policy
is selected.
5) Allow to get elements from an existing set in nf_tables.
6) Fix incorrect check in nft_hash_deactivate(), from Florian.
7) Cache netlink attribute size result in l4proto->nla_size, from
Florian.
8) Handle NFPROTO_INET in nf_ct_netns_get() from conntrack core.
9) Use power efficient workqueue in conntrack garbage collector, from
Vincent Guittot.
10) Remove unnecessary parameter, in conntrack l4proto functions, also
from Florian.
11) Constify struct nf_conntrack_l3proto definitions, from Florian.
12) Remove all typedefs in nf_conntrack_h323 via coccinelle semantic
patch, from Harsha Sharma.
13) Don't store address in the rbtree nodes in xt_connlimit, they are
never used, from Florian.
14) Fix out of bound access in the conntrack h323 helper, patch from
Eric Sesterhenn.
15) Print symbols for the address returned with %pS in IPVS, from
Helge Deller.
16) Proc output should only display its own netns in IPVS, from
KUWAZAWA Takuya.
17) Small clean up in size_entry_mwt(), from Colin Ian King.
18) Use test_and_clear_bit from nf_nat_proto_clean() instead of separated
non-atomic test and then clear bit, from Florian Westphal.
19) Consolidate prefix length maps in ipset, from Aaron Conole.
20) Fix sparse warnings in ipset, from Jozsef Kadlecsik.
21) Simplify list_set_memsize(), from simran singhal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
buf is initialized to buf_start and then set on the next statement
to buf_start + offsets[i]. Clean this up to just initialize buf
to buf_start + offsets[i] to clean up the clang build warning:
"Value stored to 'buf' during its initialization is never read"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
switch to using the new timer_setup() and from_timer() api's.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switch to using the new timer_setup() and from_timer() api's.
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan9303 driver defines eth_stp_addr as a synonym to
eth_reserved_addr_base to get the STP ethernet address 01:80:c2:00:00:00.
eth_reserved_addr_base is also used to define the start of Bridge Reserved
ethernet address range, which happen to be the STP address.
br_dev_setup refer to eth_reserved_addr_base as a definition of STP
address.
Clean up by:
- Move the eth_stp_addr definition to linux/etherdevice.h
- Use eth_stp_addr instead of eth_reserved_addr_base in br_dev_setup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for IFLA_BRPORT_NEIGH_SUPPRESS to bridge port policies.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch there was no way to tell if the vlan add operation
actually changed anything, thus we would always generate a notification
on adds. Let's make the notifications more precise and generate them
only if anything changed, so use the new bool parameter to signal that the
vlan was updated. We cannot return an error because there are valid use
cases that will be broken (e.g. overlapping range add) and also we can't
risk masking errors due to calls into drivers for vlan add which can
potentially return anything.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had cases that either sent notifications when there
were in fact no changes (e.g. non-existent vlan delete) or didn't send
notifications when there were changes (e.g. vlan add range with an error in
the middle, port flags change + vlan update error). This patch sends down
a boolean to the functions setlink/dellink use and if there is even a
single configuration change (port flag, vlan add/del, port state) then
we always send a notification. This is all done to keep backwards
compatibility with the opportunistic vlan delete, where one could
specify a vlan range that has missing vlans inside and still everything
in that range will be cleared, this is mostly used to clear the whole
vlan config with a single call, i.e. range 1-4094.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit dc709f3757 ("rtnetlink: bring NETDEV_CHANGEUPPER event
process back in rtnetlink_event"), rtnetlink_event would process the
NETDEV_CHANGEUPPER event and send a notification to userspace.
In add_del_if, it would generate NETDEV_CHANGEUPPER event by whether
netdev_master_upper_dev_link or netdev_upper_dev_unlink. There's
no need to call rtmsg_ifinfo to send the notification any more.
So this patch is to remove it from add_del_if also to avoid redundant
notifications.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan tunnels were introduced, vlan range errors got silently
dropped and instead 0 was returned always. Restore the previous
behaviour and return errors to user-space.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an access function that, given a bridge netdevice, returns whether the
bridge device is currently an mrouter or not. The function uses the already
existing br_multicast_is_router function to check that.
This function is needed in order to allow ports that join an already
existing bridge to know the current mrouter state of the bridge device.
Together with the bridge device mrouter ports switchdev notifications, it
is possible to have full offloading of the semantics of the bridge device
mcast router state.
Due to the fact that the bridge multicast router status can change in
packet RX path, take the multicast_router bridge spinlock to protect the
read.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER switchdev notification type, used
to indicate whether the bridge is or isn't mrouter. Notify when the bridge
changes its state, similarly to the already existing bridged port mrouter
notifications.
The notification uses the switchdev_attr.u.mrouter boolean flag to indicate
the current bridge mrouter status. Thus, it only indicates whether the
bridge is currently used as an mrouter or not, and does not indicate the
exact mrouter state of the bridge (learning, permanent, etc.).
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies ndisc packets
for BR_NEIGH_SUPPRESS ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies arp packets
for BR_NEIGH_SUPPRESS ports.
Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp
to support both proxy arp and neigh suppress.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to
suppress arp and nd flood on bridge ports. It implements
rfc7432, section 10.
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
This patch adds netlink and sysfs support to set this bridge port
flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack arg to br_add_if. Add messages for a couple of failures
and pass arg to netdev_master_upper_dev_link.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to netdev_upper_dev_link and netdev_master_upper_dev_link
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack to do_set_master and down to ndo_add_slave
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for ebt_in_hook to be triggered before ebt_table is assigned
resulting in a NULL-pointer dereference. Make sure hooks are
registered as the last step.
Fixes: aee12a0a37 ("ebtables: remove nf_hook_register usage")
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need to be able to transparently forward most link-local frames via
tunnels (e.g. vxlan, qinq). Currently the bridge's group_fwd_mask has a
mask which restricts the forwarding of STP and LACP, but we need to be able
to forward these over tunnels and control that forwarding on a per-port
basis thus add a new per-port group_fwd_mask option which only disallows
mac pause frames to be forwarded (they're always dropped anyway).
The patch does not change the current default situation - all of the others
are still restricted unless configured for forwarding.
We have successfully tested this patch with LACP and STP forwarding over
VxLAN and qinq tunnels.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a difference in netlink events received when an
interface is modified through bridge ioctl() or through netlink. This
patch generates additional events when an interface is added to or
removed from a bridge via ioctl().
When adding then removing an interface from a bridge with netlink, we
get:
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
Deleted 5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
When using ioctl():
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue master bridge0 state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
Deleted 5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 9e:da:60:ee:cf:c8
5: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 9e:da:60:ee:cf:c8 brd ff:ff:ff:ff:ff:ff
Without this patch, the last netlink notification is not sent.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 00ba4cb36d.
Discussion with David Ahern determined that this change is
actually not needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when an interface is released from a bridge via
ioctl(), we get a RTM_DELLINK event through netlink:
Deleted 2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 6e:23:c2:54:3a:b3
Userspace has to interpret that as a removal from the bridge, not as a
complete removal of the interface. When an bridged interface is
completely removed, we get two events:
Deleted 2: dummy0: <BROADCAST,NOARP> mtu 1500 master bridge0 state DOWN
link/ether 6e:23:c2:54:3a:b3
Deleted 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default
link/ether 6e:23:c2:54:3a:b3 brd ff:ff:ff:ff:ff:ff
In constrast, when an interface is released from a bond, we get a
RTM_NEWLINK with only the new characteristics (no master):
3: dummy1: <BROADCAST,NOARP,SLAVE,UP,LOWER_UP> mtu 1500 qdisc noqueue master bond0 state UNKNOWN group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
3: dummy1: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
4: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
3: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noqueue state DOWN group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
3: dummy1: <BROADCAST,NOARP> mtu 1500 qdisc noqueue state DOWN group default
link/ether ca:c8:7b:66:f8:25 brd ff:ff:ff:ff:ff:ff
4: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
link/ether ae:dc:7a:8c:9a:3c brd ff:ff:ff:ff:ff:ff
Userland may be confused by the fact we say a link is deleted while
its characteristics are only modified. A first solution would have
been to turn the RTM_DELLINK event in del_nbp() into a RTM_NEWLINK
event. However, maybe some piece of userland is relying on this
RTM_DELLINK to detect when a bridged interface is released. Instead,
we also emit a RTM_NEWLINK event once the interface is
released (without master info).
Deleted 2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 master bridge0 state UNKNOWN
link/ether 8a:bb:e7:94:b1:f8
2: dummy0: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default
link/ether 8a:bb:e7:94:b1:f8 brd ff:ff:ff:ff:ff:ff
This is done only when using ioctl(). When using Netlink, such an
event is already automatically emitted in do_setlink().
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using ifdef in the C file.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CONFIG_NETFILTER_DEBUG and _ASSERT() macros as they
are no longer required. Replace _ASSERT() macros with WARN_ON().
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6bc506b4fb ("bridge: switchdev: Add forward mark support for
stacked devices") added the 'offload_fwd_mark' bit to the skb in order
to allow drivers to indicate to the bridge driver that they already
forwarded the packet in L2.
In case the bit is set, before transmitting the packet from each port,
the port's mark is compared with the mark stored in the skb's control
block. If both marks are equal, we know the packet arrived from a switch
device that already forwarded the packet and it's not re-transmitted.
However, if the packet is transmitted from the bridge device itself
(e.g., br0), we should clear the 'offload_fwd_mark' bit as the mark
stored in the skb's control block isn't valid.
This scenario can happen in rare cases where a packet was trapped during
L3 forwarding and forwarded by the kernel to a bridge device.
Fixes: 6bc506b4fb ("bridge: switchdev: Add forward mark support for stacked devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Yotam Gigi <yotamg@mellanox.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends bridge fdb table tracepoints to also cover
learned fdb entries in the br_fdb_update path. Note that
unlike other tracepoints I have moved this to when the fdb
is modified because this is in the datapath and can generate
a lot of noise in the trace output. br_fdb_update is also called
from added_by_user context in the NTF_USE case which is already
traced ..hence the !added_by_user check.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few useful tracepoints to trace bridge forwarding
database updates.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
