The PHB state PNV_EEH_STATE_REMOVED maintained in pnv_phb isn't
so useful any more and it's duplicated to EEH_PE_ISOLATED. The
patch replaces PNV_EEH_STATE_REMOVED with EEH_PE_ISOLATED.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PE state (for eeh_pe instance) EEH_PE_PHB_DEAD is duplicate to
EEH_PE_ISOLATED. Originally, those PHBs (PHB PE) with EEH_PE_PHB_DEAD
would be removed from the system. However, it's safe to replace
that with EEH_PE_ISOLATED.
The patch also clear EEH_PE_RECOVERING after fenced PHB has been handled,
either failure or success. It makes the PHB PE state consistent with:
PHB functions normally NONE
PHB has been removed EEH_PE_ISOLATED
PHB fenced, recovery in progress EEH_PE_ISOLATED | RECOVERING
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes this section mismatch:
WARNING: vmlinux.o(.text+0x1efc4): Section mismatch in reference from
the function apm821xx_pciex_init_port_hw() to the function
.init.text:ppc4xx_pciex_wait_on_sdr.isra.9()
The function apm821xx_pciex_init_port_hw() references the function
__init ppc4xx_pciex_wait_on_sdr.isra.9(). This is often because
apm821xx_pciex_init_port_hw lacks a __init annotation or the
annotation of ppc4xx_pciex_wait_on_sdr.isra.9 is wrong.
apm821xx_pciex_init_port_hw is only referenced by a struct in
__initdata, so it should be safe to add __init to
apm821xx_pciex_init_port_hw.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the guest cedes the vcpu or the vcpu has no guest to
run it naps. Clear the runlatch bit of the vcpu before
napping to indicate an idle cpu.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The secondary threads in the core are kept offline before launching guests
in kvm on powerpc: "371fefd6f2dc4666:KVM: PPC: Allow book3s_hv guests to use
SMT processor modes."
Hence their runlatch bits are cleared. When the secondary threads are called
in to start a guest, their runlatch bits need to be set to indicate that they
are busy. The primary thread has its runlatch bit set though, but there is no
harm in setting this bit once again. Hence set the runlatch bit for all
threads before they start guest.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Up until now we have been setting the runlatch bits for a busy CPU and
clearing it when a CPU enters idle state. The runlatch bit has thus
been consistent with the utilization of a CPU as long as the CPU is online.
However when a CPU is hotplugged out the runlatch bit is not cleared. It
needs to be cleared to indicate an unused CPU. Hence this patch has the
runlatch bit cleared for an offline CPU just before entering an idle state
and sets it immediately after it exits the idle state.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While testing memory hot-remove, I found following dead lock:
Process #1141 is drmgr, trying to remove some memory, i.e. memory499.
It holds the memory_hotplug_mutex, and blocks when trying to remove file
"online" under dir memory499, in kernfs_drain(), at
wait_event(root->deactivate_waitq,
atomic_read(&kn->active) == KN_DEACTIVATED_BIAS);
Process #1120 is trying to online memory499 by
echo 1 > memory499/online
In .kernfs_fop_write, it uses kernfs_get_active() to increase
&kn->active, thus blocking process #1141. While itself is blocked later
when trying to acquire memory_hotplug_mutex, which is held by process
The backtrace of both processes are shown below:
[<c000000001b18600>] 0xc000000001b18600
[<c000000000015044>] .__switch_to+0x144/0x200
[<c000000000263ca4>] .online_pages+0x74/0x7b0
[<c00000000055b40c>] .memory_subsys_online+0x9c/0x150
[<c00000000053cbe8>] .device_online+0xb8/0x120
[<c00000000053cd04>] .online_store+0xb4/0xc0
[<c000000000538ce4>] .dev_attr_store+0x64/0xa0
[<c00000000030f4ec>] .sysfs_kf_write+0x7c/0xb0
[<c00000000030e574>] .kernfs_fop_write+0x154/0x1e0
[<c000000000268450>] .vfs_write+0xe0/0x260
[<c000000000269144>] .SyS_write+0x64/0x110
[<c000000000009ffc>] syscall_exit+0x0/0x7c
[<c000000001b18600>] 0xc000000001b18600
[<c000000000015044>] .__switch_to+0x144/0x200
[<c00000000030be14>] .__kernfs_remove+0x204/0x300
[<c00000000030d428>] .kernfs_remove_by_name_ns+0x68/0xf0
[<c00000000030fb38>] .sysfs_remove_file_ns+0x38/0x60
[<c000000000539354>] .device_remove_attrs+0x54/0xc0
[<c000000000539fd8>] .device_del+0x158/0x250
[<c00000000053a104>] .device_unregister+0x34/0xa0
[<c00000000055bc14>] .unregister_memory_section+0x164/0x170
[<c00000000024ee18>] .__remove_pages+0x108/0x4c0
[<c00000000004b590>] .arch_remove_memory+0x60/0xc0
[<c00000000026446c>] .remove_memory+0x8c/0xe0
[<c00000000007f9f4>] .pseries_remove_memblock+0xd4/0x160
[<c00000000007fcfc>] .pseries_memory_notifier+0x27c/0x290
[<c0000000008ae6cc>] .notifier_call_chain+0x8c/0x100
[<c0000000000d858c>] .__blocking_notifier_call_chain+0x6c/0xe0
[<c00000000071ddec>] .of_property_notify+0x7c/0xc0
[<c00000000071ed3c>] .of_update_property+0x3c/0x1b0
[<c0000000000756cc>] .ofdt_write+0x3dc/0x740
[<c0000000002f60fc>] .proc_reg_write+0xac/0x110
[<c000000000268450>] .vfs_write+0xe0/0x260
[<c000000000269144>] .SyS_write+0x64/0x110
[<c000000000009ffc>] syscall_exit+0x0/0x7c
This patch uses lock_device_hotplug() to protect remove_memory() called
in pseries_remove_memblock(), which is also stated before function
remove_memory():
* NOTE: The caller must call lock_device_hotplug() to serialize hotplug
* and online/offline operations before this call, as required by
* try_offline_node().
*/
void __ref remove_memory(int nid, u64 start, u64 size)
With this lock held, the other process(#1120 above) trying to online the
memory block will retry the system call when calling
lock_device_hotplug_sysfs(), and finally find No such device error.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
module_init should return 0 or a negative errno.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Bump the boot wrapper BOOT_COMMAND_LINE_SIZE to match the
kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I've had a report that the current limit is too small for
an automated network based installer. Bump it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two definitions of COMMAND_LINE_SIZE, one for the kernel
and one for the boot wrapper. I assume this is so the boot
wrapper can be self sufficient and not rely on kernel headers.
Having two defines with the same name is confusing, I just
updated the wrong one when trying to bump it.
Make the boot wrapper define unique by calling it
BOOT_COMMAND_LINE_SIZE.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The catalog version number was changed from a be32 (with proceeding
32bits of padding) to a be64, update the code to treat it as a be64
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
fixup for "powerpc/perf: Add support for the hv gpci (get performance
counter info) interface".
Makes the "not enabled" message less awful (and hidden unless
debugging).
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
fixup for "powerpc/perf: Add support for the hv 24x7 interface"
Makes the "not enabled" message less awful (and hides it in most cases).
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The if condition check was based on a draft ISA doc. Remove the same.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two copies of code that creates an OPAL sg list. Consolidate
these into a common set of helpers and fix the endian issues.
The flash interface embedded a version number in the num_entries
field, whereas the dump interface did did not. Since versioning
wasn't added to the flash interface and it is impossible to add
this in a backwards compatible way, just remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix little endian issues with the OPAL error log code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The bitmap in opal_poll_events and opal_handle_interrupt is
big endian, so we need to byteswap it on little endian builds.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We had some duplication of the internal OPAL functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Using size_t in our APIs is asking for trouble, especially
when some OPAL calls use size_t pointers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PowerNV platform, we are holding an unnecessary refcount on a pci_dev, which
leads to the pci_dev is not destroyed when hotplugging a pci device.
This patch release the unnecessary refcount.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With this patch I was able to update firmware on an LE kernel.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a subtle race when sending CPUs back to OPAL on kexec.
We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.
However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.
The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The size of the sysparam sysfs files is determined from the device tree
at boot. However the buffer is hard coded to 64 bytes. If we encounter a
parameter that is larger than 64, or miss-parse the device tree, the
buffer will overflow when reading or writing to the parameter.
Check it at discovery time, and if the parameter is too large, do not
create a sysfs entry for it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The sysparam code currently uses the userspace supplied number of
bytes when memcpy()ing in to a local 64-byte buffer.
Limit the maximum number of bytes by the size of the buffer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The OPAL calls are returning int64_t values, which the sysparam code
stores in an int, and the sysfs callback returns ssize_t. Make code a
easier to read by consistently using ssize_t.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When a sysparam query in OPAL returned a negative value (error code),
sysfs would spew out a decent chunk of memory; almost 64K more than
expected. This was traced to a sign/unsigned mix up in the OPAL sysparam
sysfs code at sys_param_show.
The return value of sys_param_show is a ssize_t, calculated using
return ret ? ret : attr->param_size;
Alan Modra explains:
"attr->param_size" is an unsigned int, "ret" an int, so the overall
expression has type unsigned int. Result is that ret is cast to
unsigned int before being cast to ssize_t.
Instead of using the ternary operator, set ret to the param_size if an
error is not detected. The same bug exists in the sysfs write callback;
this patch fixes it in the same way.
A note on debugging this next time: on my system gcc will warn about
this if compiled with -Wsign-compare, which is not enabled by -Wall,
only -Wextra.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 41dd03a9 may cause Oops in rtas_stop_self().
The reason is that the rtas_args was moved into stack space. For a box
with more that 4GB RAM, the stack could easily be outside 32bit range,
but RTAS is 32bit.
So the patch moves rtas_args away from stack by adding static before
it.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit aac416fc38 (lkdtm: flush icache and report actions) calls
flush_icache_range from a module. It's exported on most architectures
that implement it, but not on powerpc. This patch exports it to fix
the module link failure.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Build the little endian ppc64 kernel with ABIv2 if the toolchain
supports it. We can identify an ABIv2 capable toolchain by the
-mabi=elfv2 compiler flag.
Signed-off-by: Anton Blanchard <anton@samba.org>
__ftrace_make_call assumed ABIv1 TOC stack offsets, so it
broke on ABIv2.
While we are here, we can simplify the instruction modification
code. Since we always update one instruction there is no need to
probe_kernel_write and flush_icache_range, just use patch_branch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Now we have is_module_trampoline() and module_trampoline_target()
we can remove a bunch of intimate kernel module trampoline
knowledge from ftrace.
Signed-off-by: Anton Blanchard <anton@samba.org>
ftrace has way too much knowledge of our kernel module trampoline
layout hidden inside it. Create module_trampoline_target() that gives
the target address of a kernel module trampoline.
Signed-off-by: Anton Blanchard <anton@samba.org>
ftrace has way too much knowledge of our kernel module trampoline
layout hidden inside it. Create is_module_trampoline() that can
abstract this away inside the module loader code.
Signed-off-by: Anton Blanchard <anton@samba.org>
When testing the ftrace function tracer, I realised that ftrace_caller
and mcount are called from modules and they both call into C, therefore
they need the ABIv2 global entry point to establish r2.
Signed-off-by: Anton Blanchard <anton@samba.org>
If an assembly function that calls back into c code is exported to
modules, we need to ensure r2 is setup correctly. There are only
two places crazy enough to do it (two of which are my fault).
Signed-off-by: Anton Blanchard <anton@samba.org>
ELFv2 doesn't use function descriptors, because it doesn't need to
load a new r2 when calling into a function. On the other hand, you're
supposed to use a local entry point for R_PPC_REL24 branches.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In ELFv2, r12 is supposed to equal to PC on entry to a function.
Our stubs use r11, so change swap that with r12.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
ELFv2 doesn't use function descriptors, so we don't expect symbols to
start with ".". But because depmod and modpost strip ".", and we have
the special symbol ".TOC.", we still need to do it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The new ELF ABI tends to use R_PPC64_REL16_LO and R_PPC64_REL16_HA
relocations (PC-relative), so implement them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
