The fec/enet driver calculates MDC rate with the formula below.
ref_freq / ((MII_SPEED + 1) x 2)
The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now. And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec. This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz). That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz. And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.
Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
These systems all use saif0 as the mclock provider to codec sgtl5000.
Reflect that in device tree source, so that sgtl5000 can find the clock
by calling clk_get().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The correct muxing for emi_sel clock should be
2b'00 - 396M PFD
2b'01 - PLL3
2b'10 - AXI clk root
2b'11 - 352M PFD
This patch corrects the muxing in the clock driver.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
The current default pad configuration for UART RX and TX pads sets a 360k
pull-down and writes 1 to a reserved bit (1 << 0). It doesn't seem right to
me that in idle state, the UART has to keep the signal high against a
pull-down resistor.
This patch instead sets a 100k pull-up, which incidentally corresponds to the
register reset value for all but one (MX53_PAD_KEY_ROW0__UART4_RXD_MUX) pad,
and removes the write to the reserved bit.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/x86 uses of the __cpuinit macros from
all C files. x86 only had the one __CPUINIT used in assembly files,
and it wasn't paired off with a .previous or a __FINIT, so we can
delete it directly w/o any corresponding additional change there.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/score uses of the __cpuinit macros from
all C files. Currently score does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/xtensa uses of the __cpuinit macros from
all C files. Currently xtensa does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/openrisc uses of the __cpuinit macros from
all C files. Currently openrisc does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/m32r uses of the __cpuinit macros from
all C files. Currently m32r does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: linux-m32r@ml.linux-m32r.org
Cc: linux-m32r-ja@ml.linux-m32r.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/hexagon uses of the __cpuinit macros from
all C files. Currently hexagon does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/frv uses of the __cpuinit macros from
all C files. Currently frv does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/cris uses of the __cpuinit macros from
all C files. Currently cris does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: linux-cris-kernel@axis.com
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/metag uses of the __cpuinit macros from
all C files. Currently metag does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/tile uses of the __cpuinit macros from
all C files. Currently tile does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/sh uses of the __cpuinit macros from
all C files. Currently sh does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/s390 uses of the __cpuinit macros from
all C files. Currently s390 does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/blackfin uses of the __cpuinit macros from
all C files. Currently blackfin does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/arm64 uses of the __cpuinit macros from
all C files. Currently arm64 does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/sparc uses of the __cpuinit macros from
C files and removes __CPUINIT from assembly files. Note that even
though arch/sparc/kernel/trampoline_64.S has instances of ".previous"
in it, they are all paired off against explicit ".section" directives,
and not implicitly paired with __CPUINIT (unlike mips and arm were).
[1] https://lkml.org/lkml/2013/5/20/589
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the parisc uses of the __cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the alpha uses of the __cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull more vfs stuff from Al Viro:
"O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
making simple_lookup() usable for filesystems with non-NULL s_d_op,
which allows us to get rid of quite a bit of ugliness"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sunrpc: now we can just set ->s_d_op
cgroup: we can use simple_lookup() now
efivarfs: we can use simple_lookup() now
make simple_lookup() usable for filesystems that set ->s_d_op
configfs: don't open-code d_alloc_name()
__rpc_lookup_create_exclusive: pass string instead of qstr
rpc_create_*_dir: don't bother with qstr
llist: llist_add() can use llist_add_batch()
llist: fix/simplify llist_add() and llist_add_batch()
fput: turn "list_head delayed_fput_list" into llist_head
fs/file_table.c:fput(): add comment
Safer ABI for O_TMPFILE
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Pull perf fixes from Thomas Gleixner:
- fix for do_div() abuse on x86
- locking fix in perf core
- a pile of (build) fixes and cleanups in perf tools
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86: Fix incorrect use of do_div() in NMI warning
perf: Fix perf_lock_task_context() vs RCU
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
perf: Clone child context from parent context pmu
perf script: Fix broken include in Context.xs
perf tools: Fix -ldw/-lelf link test when static linking
perf tools: Revert regression in configuration of Python support
perf tools: Fix perf version generation
perf stat: Fix per-socket output bug for uncore events
perf symbols: Fix vdso list searching
perf evsel: Fix missing increment in sample parsing
perf tools: Update symbol_conf.nr_events when processing attribute events
perf tools: Fix new_term() missing free on error path
perf tools: Fix parse_events_terms() segfault on error path
perf evsel: Fix count parameter to read call in event_format__new
perf tools: fix a typo of a Power7 event name
perf tools: Fix -x/--exclude-other option for report command
perf evlist: Enhance perf_evlist__start_workload()
perf record: Remove -f/--force option
perf record: Remove -A/--append option
...
This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real use
(and testing) out of the box on hardware.
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fKfy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Pull ARM fixes from Russell King:
"A few fixes for ARM, mostly just one liners with the exception of the
missing section specification. We decided not to rely on .previous to
fix this but to explicitly state the section we want the code to be
in."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7778/1: smp_twd: twd_update_frequency need be run on all online CPUs
ARM: 7782/1: Kconfig: Let ARM_ERRATA_364296 not depend on CONFIG_SMP
ARM: mm: fix boot on SA1110 Assabet
ARM: 7781/1: mmu: Add debug_ll_io_init() mappings to early mappings
ARM: 7780/1: add missing linker section markup to head-common.S
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
[suggested by Rasmus Villemoes] make O_DIRECTORY | O_RDWR part of O_TMPFILE;
that will fail on old kernels in a lot more cases than what I came up with.
And make sure O_CREAT doesn't get there...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
OMAP recently changed how the platforms are configured, so OMAP2/3/4 SoC
support is no longer enabled by default. Add them back.
Enable new ethernet driver for sunxi.
The i.MX console options moved due to resorting, no functional change.
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=qQ9Q
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij:
Ux500 defconfig changes:
- Update base due to different Kconfig changes
- Select watchdog, MUSB, Ux500 ALSA SoC, various MMC/SD
features and enable highmem
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable HIGHMEM in the u8500 defconfig
ARM: ux500: Update MMC configs for u8500 defconfig
ARM: ux500: select SND_SOC_UX500 for ux500
ARM: ux500: update defconfig base
ARM: ux500: select WATCHDOG and MUSB for ux500
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add i.MX serial console support. This gives us the boot messages on
UART on e.g. the i.MX6Q sabre sd platform.
- Add the necessary config options, to allow booting with NFS root on
an i.MX6 sabre sd.
- Add Freescale LPUART serial console support. This gives us the boot
messages on UART on e.g. the Vybrid VF610 Tower board.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Russell King <linux@arm.linux.org.uk>
[olof: squashed three commits down to one]
Signed-off-by: Olof Johansson <olof@lixom.net>
get in before -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kO4u
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Omap fixes and minor defconfig updates that would be good to
get in before -rc1.
* tag 'omap-for-v3.11/fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
ARM: scu: provide inline dummy functions when SCU is not present
ARM: OMAP4: sleep: build OMAP4 specific functions only for OMAP4
ARM: OMAP2+: timer: initialize before using oh_name
Signed-off-by: Olof Johansson <olof@lixom.net>
Add/move/change conflicts in arch/arm/mach-omap2/Kconfig resolved.
I completely botched understanding the calling conventions of
do_div(). I assumed that do_div() returned the result instead
of realizing that it modifies its argument and returns a
remainder. The side-effect from this would be bogus numbers
for the "msecs" value in the warning messages:
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.114 msecs
Note, there was a second fix posted by Stephane Eranian for
a separate patch which I also botched:
http://lkml.kernel.org/r/20130704223010.GA30625@quad
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20130708214404.B0B6EA66@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
This reverts commit 1acba98f81.
The firmware on both Dave's Thinkpad and Maarten's Macbook Pro appear to
rely on the old behaviour, and their machines fail to boot with the
above commit.
Reported-by: Dave Young <dyoung@redhat.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Pull more KVM changes from Gleb Natapov:
"A fix for a bug that prevents some guests from working on old Intel
CPUs and a patch that integrates ARM64 KVM, merged via ARM64 tree,
into Kconfig."
* tag 'kvm-3.11-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: mark unusable segment as nonpresent
arm64: KVM: Kconfig integration
Pull Sparc bugfixes from David Miller:
"Four bug fixes:
1) Enable snoop tags properly on Sparc32/LEON, from Andreas Larsson
2) strcpy() length check fix from Chen Gang.
3) Forgotten unregister_netdev() in sunvnet driver, from Dave
Kleikamp.
4) Fix broken assembler offsets used in vm_area_struct accesses on
sparc32, from Olivier DANET."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
[PATCH] sparc32: vm_area_struct access for old Sun SPARCs.
sunvnet: vnet_port_remove must call unregister_netdev
sparc32, leon: Require separate snoop tags set to regard snooping to be enabled
arch: sparc: kernel: check the memory length before use strcpy().
Merge more patches from Andrew Morton:
"The rest of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: remove free_area_cache
zswap: add documentation
zswap: add to mm/
zbud: add to mm/
Since all architectures have been converted to use vm_unmapped_area(),
there is no remaining use for the free_area_cache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename LL_SO to BUSY_POLL_SO
Rename sysctl_net_ll_{read,poll} to sysctl_busy_{read,poll}
Fix up users of these variables.
Fix documentation for sysctl.
a patch for the socket.7 man page will follow separately,
because of limitations of my mail setup.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf fixes from Ingo Molnar:
"Two small fixlets"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix interrupt handler timing harness
perf/x86/amd: Do not print an error when the device is not present
Commit e4c6bfd2d7 ("mm: rearrange
vm_area_struct for fewer cache misses") changed the layout of the
vm_area_struct structure, it broke several SPARC32 assembly routines
which used numerical constants for accessing the vm_mm field.
This patch defines the VMA_VM_MM constant to replace the immediate values.
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if data snooping is enabled, without separate snoop tags snooping will not
work when the MMU is enabled.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the related next strcpy(), the destination length is less than 512,
but the source maximize length may be 'OPROMMAXPARAM' (4096) which is
more than 512.
One work flow may:
openprom_sunos_ioctl() -> if (cmd == OPROMSETOPT)
getstrings() -> will alloc buffer with size 'OPROMMAXPARAM'.
opromsetopt() -> devide the buffer into 'var' and 'value'
of_set_property() -> pass
prom_setprop() -> pass
ldom_set_var()
And do not mind the additional 4 alignment buffer increasing, since
'sizeof(pkt) - sizeof(pkt.header)' is 4 alignment at least.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core:
- Add support for eMMC 5.1 devices.
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power management
of eMMC/SD between requests, using runtime PM.
- Add an ioctl to perform the eMMC 4.5 Sanitize command; sample code at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs.
- dw_mmc: Add support for Altera SoCFPGAs.
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable cards.
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs.
- sdhi/tmio: Add DT DMA support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=c/CM
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.11:
Core:
- Add support for eMMC 5.1 devices
- Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power
management of eMMC/SD between requests, using runtime PM
- Add an ioctl to perform the eMMC 4.5 Sanitize command. Sample code
at:
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git
Drivers:
- dw_mmc: Add support for Rockchip's Cortex-A9 SoCs
- dw_mmc: Add support for Altera SoCFPGAs
- sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable
cards
- sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs
- sdhi/tmio: Add DT DMA support"
* tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (87 commits)
mmc: bcm281xx SDHCI driver
mmc: sdhci: add card_event callback to sdhci
mmc: core: Fixup Oops for SDIO shutdown
mmc: sdhci-pci: add another device id
mmc: esdhc: Fix bug when writing to SDHCI_HOST_CONTROL register
mmc: esdhc: Add support for 8-bit bus width and non-removable card
mmc: core: production year for eMMC 4.41 and later
mmc: omap: remove unnecessary #if 0's
mmc: sdhci: fix ctrl_2 on super-speed selection
mmc: dw_mmc-pltfm: add Rockchip variant
mmc: dw_mmc-pltfm: move probe and remove below dt match table
mmc: dw_mmc-pltfm: remove static from dw_mci_pltfm_remove
mmc: sdhci-acpi: add support for eMMC hardware reset for HID 80860F14
mmc: sdhci-pci: add support for eMMC hardware reset for BYT eMMC.
mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA
mmc: sdhci: fix caps2 for HS200
sdhci-pxav3: Fix runtime PM initialization
mmc: core: Add DT-bindings for MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Invent MMC_CAP2_FULL_PWR_CYCLE
mmc: core: Enable power_off_notify for eMMC shutdown sequence
...
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator subdevice
addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need since
commit 0998d063.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RqMp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For the 3.11 merge we only have one new MFD driver for the Kontron
PLD.
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich
driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator
subdevice addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need
since commit 0998d06310 ("device-core: Ensure drvdata = NULL when
no driver is bound")
* tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (102 commits)
mfd: sec: Provide max_register to regmap
mfd: wm8994: Remove duplicate check for active JACKDET
MAINTAINERS: Add include directory to MFD file patterns
mfd: sec: Remove fields not used since regmap conversion
watchdog: Kontron PLD watchdog timer driver
mfd: max8998: Add support for Device Tree
regulator: max8998: Use arrays for specifying voltages in platform data
mfd: max8998: Add irq domain support
regulator: palmas: Add TPS659038 support
mfd: Kontron PLD mfd driver
mfd: palmas: Add TPS659038 PMIC support
mfd: palmas: Add SMPS10_BOOST feature
mfd: palmas: Check if irq is valid
mfd: lpc_ich: iTCO_wdt patch for Intel Coleto Creek DeviceIDs
mfd: twl-core: Change TWL6025 references to TWL6032
mfd: davinci_voicecodec: Fix build breakage
mfd: vexpress: Make the driver optional for arm and arm64
mfd: htc-egpio: Use devm_ioremap_nocache() instead of ioremap_nocache()
mfd: davinci_voicecodec: Convert to use devm_* APIs
mfd: twl4030-power: Fix relocking on error
...
Pull x86 fix from Ingo Molnar:
"irq-tracing fixlet"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tracing: Add irq_enter/exit() in smp_trace_reschedule_interrupt()
Pull microblaze update from Michal Simek:
"This Microblaze merge window is quite minimal.
I have also added to my branch one xilinx systemace sparse fix because
haven't got any reply from block maintainer."
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
xilinx systemace: Fix sparse warnings
microblaze: Move __NR_syscalls from uapi
microblaze: Enable KGDB in defconfig
microblaze: Don't mark arch_kgdb_ops as const.
This is just a single fix to fix bad UDP checksums sometimes being
generated to IP addresses *.*.255.255.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Gu8G
-----END PGP SIGNATURE-----
Merge tag 'metag-fixes-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fixes from James Hogan:
"This is just a single fix to fix bad UDP checksums sometimes being
generated to IP addresses *.*.255.255"
* tag 'metag-fixes-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: checksum.h: fix carry in csum_tcpudp_nofold
corresponding drivers (net/ethernet/arc/*, irqctl/irq-tb10x.c) have now
been merged into your tree.
Ideally these shd have been part of same submissions, oh well...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QgUU
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull second set of ARC architecture updates from Vineet Gupta:
"Couple of Platform updates (Device Tree files primarily) given that
the corresponding drivers (net/ethernet/arc/*, irqctl/irq-tb10x.c)
have now been merged into your tree.
Ideally these shd have been part of same submissions, oh well..."
* tag 'arc-v3.11-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [TB10x] Updates for irqchip driver
ARC: [plat-arcfpga] Enable arc_emac for ARCAngle4 Board
Pull parisc updates from Helge Deller:
"The PA-RISC updates for v3.11 include a gcc miscompilation fix,
gzip-compressed vmlinuz support, a fix in the PCI code for ATI FireGL
support on c8000 machines, a fix to prevent that %sr1 is being
clobbered and a few smaller optimizations and documentation updates"
* 'parisc-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix gcc miscompilation in pa_memcpy()
parisc: Ensure volatile space register %sr1 is not clobbered
parisc: optimize mtsp(0,sr) inline assembly
parisc: switch to gzip-compressed vmlinuz kernel
parisc: document the shadow registers
parisc: more capabilities info in /proc/cpuinfo
parisc: fix LMMIO mismatch between PAT length and MASK register
The reason is that other applications like strace
think that every __NR_xx is syscall.
Also __NR_syscalls is not used by user applications/libs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
When the local timer freq changed, the twd_update_frequency function
should be run all the CPUs include itself, otherwise, the twd freq will
not get updated and the local timer will not run correcttly.
smp_call_function will run functions on all other CPUs, but not include
himself, this is not correct,use on_each_cpu instead to fix this issue.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
imx_v6_v7_defconfig handles both multi-core and single-core SoCs, and it has CONFIG_SMP=y selected by default.
With such config we cannot select ARM_ERRATA_364296, as it depends on !SMP.
Let ARM_ERRATA_364296 be undependent on CONFIG_SMP, so that we can select this erratum for the ARM1136 SoCs, even if CONFIG_SMP=y is enabled.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When running the LTP testsuite one may hit this kernel BUG() with the
write06 testcase:
kernel BUG at mm/filemap.c:2023!
CPU: 1 PID: 8614 Comm: writev01 Not tainted 3.10.0-rc7-64bit-c3000+ #6
IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000401e6e84 00000000401e6e88
IIR: 03ffe01f ISR: 0000000010340000 IOR: 000001fbe0380820
CPU: 1 CR30: 00000000bef80000 CR31: ffffffffffffffff
ORIG_R28: 00000000bdc192c0
IAOQ[0]: iov_iter_advance+0x3c/0xc0
IAOQ[1]: iov_iter_advance+0x40/0xc0
RP(r2): generic_file_buffered_write+0x204/0x3f0
Backtrace:
[<00000000401e764c>] generic_file_buffered_write+0x204/0x3f0
[<00000000401eab24>] __generic_file_aio_write+0x244/0x448
[<00000000401eadc0>] generic_file_aio_write+0x98/0x150
[<000000004024f460>] do_sync_readv_writev+0xc0/0x130
[<000000004025037c>] compat_do_readv_writev+0x12c/0x340
[<00000000402505f8>] compat_writev+0x68/0xa0
[<0000000040251d88>] compat_SyS_writev+0x98/0xf8
Reason for this crash is a gcc miscompilation in the fault handlers of
pa_memcpy() which return the fault address instead of the copied bytes.
Since this seems to be a generic problem with gcc-4.7.x (and below), it's
better to simplify the fault handlers in pa_memcpy to avoid this problem.
Here is a simple reproducer for the problem:
int main(int argc, char **argv)
{
int fd, nbytes;
struct iovec wr_iovec[] = {
{ "TEST STRING ",32},
{ (char*)0x40005000,32} }; // random memory.
fd = open(DATA_FILE, O_RDWR | O_CREAT, 0666);
nbytes = writev(fd, wr_iovec, 2);
printf("return value = %d, errno %d (%s)\n",
nbytes, errno, strerror(errno));
return 0;
}
In addition, John David Anglin wrote:
There is no gcc PR as pa_memcpy is not legitimate C code. There is an
implicit assumption that certain variables will contain correct values
when an exception occurs and the code randomly jumps to one of the
exception blocks. There is no guarantee of this. If a PR was filed, it
would likely be marked as invalid.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.8+
Signed-off-by: Helge Deller <deller@gmx.de>
I still see the occasional random segv on rp3440. Looking at one of
these (a code 15), it appeared the problem must be with the cache
handling of anonymous pages. Reviewing this, I noticed that the space
register %sr1 might be being clobbered when we flush an anonymous page.
Register %sr1 is used for TLB purges in a couple of places. These
purges are needed on PA8800 and PA8900 processors to ensure cache
consistency of flushed cache lines.
The solution here is simply to move the %sr1 load into the TLB lock
region needed to ensure that one purge executes at a time on SMP
systems. This was already the case for one use. After a few days of
operation, I haven't had a random segv on my rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
If the value which should be moved into a space register is zero, we can
optimize the inline assembly to become "mtsp %r0,%srX".
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 3.10
The latest PA-RISC Boot Loader (palo) allows loading of gzip compressed
vmlinuz kernels. So let's now switch to build a vmlinuz file when we
build a palo boot image.
PALO version 1.9 (or higher) is required for this which is available at
git://git.kernel.org/pub/scm/linux/kernel/git/deller/palo.git
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # 3.10
Merge together the unicore32, arm, and x86 reboot= command line
parameter handling.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for the moving the parsing of reboot= to the generic kernel code
by making reboot_mode into a more generic form.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These restart_mode fields are not used at all. Remove them to make
moving the reboot= cmdline options to the general kernel easier.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for the moving the parsing of reboot= to the generic kernel code
by making reboot_mode into a more generic form.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for the moving the parsing of reboot= to the generic kernel code
by making reboot_mode into a more generic form.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Miguel Boton <mboton.lkml@gmail.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
flush_ptrace_hw_breakpoint() destroys the counters set by ptrace, but
"leaks" ->debugreg6 and ->ptrace_dr7.
The problem is minor, but still it doesn't look right and flush_thread()
did this until commit 66cb591729 ("hw-breakpoints: use the new wrapper
routines to access debug registers in process/thread code"). Now that
PTRACE_DETACH does flush_ too this makes even more sense.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ptrace_set_debugreg() is trivial but looks horrible. Kill the unnecessary
goto's and return's to cleanup the code.
This matches ptrace_get_debugreg() which also needs the trivial whitespace
cleanups.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 24f1e32c60 ("hw-breakpoints: Rewrite the hw-breakpoints layer
on top of perf events") introduced the minor regression. Before this
commit
PTRACE_POKEUSER DR7, enableDR0
PTRACE_POKEUSER DR0, address
was perfectly valid, now PTRACE_POKEUSER(DR7) fails if DR0 was not
previously initialized by PTRACE_POKEUSER(DR0).
Change ptrace_write_dr7() to do ptrace_register_breakpoint(addr => 0) if
!bp && !disabled.
This fixes watchpoint-zeroaddr from ptrace-tests, see
https://bugzilla.redhat.com/show_bug.cgi?id=660204.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes, preparation.
Extract the "register breakpoint" code from ptrace_get_debugreg() into
the new/generic helper, ptrace_register_breakpoint(). It will have more
users.
The patch also adds another simple helper, ptrace_fill_bp_fields(), to
factor out the arch_bp_generic_fields() logic in register/modify.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ptrace_write_dr7() skips ptrace_modify_breakpoint(disabled => true)
unless second_pass, this buys nothing but complicates the code and means
that we always do the main loop twice even if "disabled" was never true.
The comment says:
Don't unregister the breakpoints right-away,
unless all register_user_hw_breakpoint()
requests have succeeded.
Firstly, we do not do register_user_hw_breakpoint(), it was removed by
commit 24f1e32c60 ("hw-breakpoints: Rewrite the hw-breakpoints layer
on top of perf events").
We are going to restore register_user_hw_breakpoint() (see the next
patch) but this doesn't matter: after commit 44234adcdc
("hw-breakpoints: Modify breakpoints without unregistering them")
perf_event_disable() can not hurt, hw_breakpoint_del() does not free the
slot.
Remove the "second_pass" check from the main loop and simplify the code.
Since we have to check "bp != NULL" anyway, the patch also removes the
same check in ptrace_modify_breakpoint() and moves the comment into
ptrace_write_dr7().
With this patch the second pass is only needed to restore the saved
old_dr7. This should never fail, so the patch adds WARN_ON() to catch
the potential problems as Frederic suggested.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ptrace_write_dr7() looks unnecessarily overcomplicated. We can factor
out ptrace_modify_breakpoint() and do not do "continue" twice, just we
need to pass the proper "disabled" argument to
ptrace_modify_breakpoint().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit e0ac8457d0 ("hw_breakpoints: Fix racy access to
ptrace breakpoints").
The patch was fine but we can no longer race with SIGKILL after commit
9899d11f65 ("ptrace: ensure arch_ptrace/ptrace_request can never race
with SIGKILL"), the __TASK_TRACED tracee can't be woken up and
->ptrace_bps[] can't go away.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit bf0b8f4b55 ("hw_breakpoints: Fix racy access to
ptrace breakpoints").
The patch was fine but we can no longer race with SIGKILL after commit
9899d11f65 ("ptrace: ensure arch_ptrace/ptrace_request can never race
with SIGKILL"), the __TASK_TRACED tracee can't be woken up and
->ptrace_bps[] can't go away.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 07fa7a0a8a ("hw_breakpoints: Fix racy access to
ptrace breakpoints") and removes ptrace_get/put_breakpoints() added by
other commits.
The patch was fine but we can no longer race with SIGKILL after commit
9899d11f65 ("ptrace: ensure arch_ptrace/ptrace_request can never race
with SIGKILL"), the __TASK_TRACED tracee can't be woken up and
->ptrace_bps[] can't go away.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 87dc669ba2 ("hw_breakpoints: Fix racy access to
ptrace breakpoints").
The patch was fine but we can no longer race with SIGKILL after commit
9899d11f65 ("ptrace: ensure arch_ptrace/ptrace_request can never race
with SIGKILL"), the __TASK_TRACED tracee can't be woken up and
->ptrace_bps[] can't go away.
The patch only removes ptrace_get_breakpoints/ptrace_put_breakpoints and
does a couple of "while at it" cleanups, it doesn't remove other changes
from the reverted commit.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old codes accumulate addr to get right pmd, however, currently pmds
are preallocated and transfered as a parameter, there is unnecessary to
accumulate addr variable any more, this patch remove it.
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few remaining architectures directly kill the page faulting task in an
out of memory situation. This is usually not a good idea since that
task might not even use a significant amount of memory and so may not be
the optimal victim to resolve the situation.
Since 2.6.29's 1c0fe6e ("mm: invoke oom-killer from page fault") there
is a hook that architecture page fault handlers are supposed to call to
invoke the OOM killer and let it pick the right task to kill. Convert
the remaining architectures over to this hook.
To have the previous behavior of simply taking out the faulting task the
vm.oom_kill_allocating_task sysctl can be set to 1.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc bits]
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In csum_tcpudp_nofold, add 1 if the carry bit is set after adding the
destination IP address (32 bits) to the checksum (16 bits).
The lack of carry handling for this particular addition meant that a
destination address of *.*.255.255 (e.g. certain broadcasts) sometimes
resulted in an incorrect checksum. This bug has been present in the Meta
port since the code was written in the 2.4 days.
Reported-by: Marcin Nowakowski <Marcin.Nowakowski@pure.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Commit 83db0384 (mm/ARM: use common help functions to free reserved
pages) broke booting on the Assabet by trying to convert a PFN to
a virtual address using the __va() macro. This macro takes the
physical address, not a PFN. Fix this.
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Failure to add the mapping created in debug_ll_io_init() can lead
to the BUG_ON() triggering in lib/ioremap.c:27 if the static
virtual address decided for the debug_ll mapping overlaps with
another mapping that is created later. This happens because the
generic ioremap code has no idea there is a mapping there and it
tries to place a mapping in the same location and blows up when
it sees that there is a pte already present.
kernel BUG at lib/ioremap.c:27!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-rc2-00042-g2af0c67-dirty #316
task: ef088000 ti: ef082000 task.ti: ef082000
PC is at ioremap_page_range+0x16c/0x198
LR is at ioremap_page_range+0xf0/0x198
pc : [<c04cb874>] lr : [<c04cb7f8>] psr: 20000113
sp : ef083e78 ip : af140000 fp : ef083ebc
r10: ef7fc100 r9 : ef7fc104 r8 : 000af174
r7 : 00000647 r6 : beffffff r5 : f004c000 r4 : f0040000
r3 : af173417 r2 : 16440653 r1 : af173e07 r0 : ef7fc8fc
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 8020406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xef082238)
Stack: (0xef083e78 to 0xef084000)
3e60: 00040000 ef083eec
3e80: bf134000 f004bfff c0207c00 f004c000 c02fc120 f000c000 c15e7800 00040000
3ea0: ef083eec 00000647 c098ba9c c0953544 ef083edc ef083ec0 c021b82c c04cb714
3ec0: c09cdc50 00000040 ef0f1e00 ef1003c0 ef083f14 ef083ee0 c09535bc c021b7bc
3ee0: c0953544 c04d0c6c c094e2cc c1600be4 c07440c4 c09a6888 00000002 c0a15f00
3f00: ef082000 00000000 ef083f54 ef083f18 c0208728 c0953550 00000002 c1600bfc
3f20: c08e3fac c0839918 ef083f54 c1600b80 c09a6888 c0a15f00 0000008b c094e2cc
3f40: c098ba9c c098bab8 ef083f94 ef083f58 c094ea0c c020865c 00000002 00000002
3f60: c094e2cc 00000000 c025b674 00000000 c06ff860 00000000 00000000 00000000
3f80: 00000000 00000000 ef083fac ef083f98 c06ff878 c094e910 00000000 00000000
3fa0: 00000000 ef083fb0 c020efe8 c06ff86c 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 c0595108
[<c04cb874>] (ioremap_page_range+0x16c/0x198) from [<c021b82c>] (__alloc_remap_buffer.isra.18+0x7c/0xc4)
[<c021b82c>] (__alloc_remap_buffer.isra.18+0x7c/0xc4) from [<c09535bc>] (atomic_pool_init+0x78/0x128)
[<c09535bc>] (atomic_pool_init+0x78/0x128) from [<c0208728>] (do_one_initcall+0xd8/0x198)
[<c0208728>] (do_one_initcall+0xd8/0x198) from [<c094ea0c>] (kernel_init_freeable+0x108/0x1d0)
[<c094ea0c>] (kernel_init_freeable+0x108/0x1d0) from [<c06ff878>] (kernel_init+0x18/0xf4)
[<c06ff878>] (kernel_init+0x18/0xf4) from [<c020efe8>] (ret_from_fork+0x14/0x20)
Code: e50b0040 ebf54b2f e51b0040 eaffffee (e7f001f2)
Fix it by telling generic layers about the static mapping via
iotable_init(). This also has the nice side effect of letting
you see the mapping in procfs' vmallocinfo file.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Macro __INIT is used to place various code in head-common.S into the init
section. This should be matched by a closing __FINIT. Also, add an
explicit ".text" to ensure subsequent code is placed into the correct
section; __FINIT is simply a closing marker to match __INIT and doesn't
guarantee to revert to .text.
This historically caused no problem, because macro __CPUINIT was used at
the exact location where __FINIT was missing, which then placed following
code into the cpuinit section. However, with commit 22f0a2736 "init.h:
remove __cpuinit sections from the kernel" applied, __CPUINIT becomes a
no-op, thus leaving all this code in the init section, rather than the
regular text section. This caused issues such as secondary CPU boot
failures or crashes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"ARM: OMAP: build mach-omap code only if needed" moved around the
ARCH_OMAP2PLUS stanza, but accidentally dropped the seleciton of
TI_PRIV_EDMA in the process. Add it back.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
release boot lock earlier to let coreb do setup and calibrate
set coreb online later after initialization ready
add BFIN_IPI_NONE IPI type
drop unnecesarry smp_mb() and using atomic type
Signed-off-by: Steven Miao <realmz6@gmail.com>
In the Power7 PMU guide:
https://www.power.org/documentation/commonly-used-metrics-for-performance-analysis/
PM_BRU_MPRED is referred to as PM_BR_MPRED.
It fixed the typo by changing the name of the event in kernel and
documentation accordingly.
This patch changes the ABI, there are some reasons I think it's ok:
- It is relatively new interface, specific to the Power7 platform.
- No tools that we know of actually use this interface at this point
(none are listed near the interface).
- Users of this interface (eg oprofile users migrating to perf)
would be more used to the "PM_BR_MPRED" rather than "PM_BRU_MPRED".
- These are in the ABI/testing at this point rather than ABI/stable,
so hoping we have some wiggle room.
Signed-off-by: Runzhen Wang <runzhen@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Cc: icycoder@gmail.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Runzhen Wang <runzhew@clemson.edu>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1372407297-6996-2-git-send-email-runzhen@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pointers in the efi_runtime_services_t structure now have type
"void *" (formerly they were "unsigned long"). So we now see a
bunch of warnings like this:
arch/ia64/hp/sim/boot/fw-emu.c:293: warning: assignment makes pointer from integer without a cast
Add (void *) casts to the 10 affected lines to make the build quiet again.
Signed-off-by: Tony Luck <tony.luck@intel.com>
kmap_atomic allows only one argument now, just remove the unused 'kmtype'.
Signed-off-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
flat DT copy code calls bootmem allocator with @align = 0.
This is probably OK with legacy allocator which xtensa uses right now,
but this will panic right away with memblock allocator
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Marc Gauthier <marc@tensilica.com>
Cc: linux-xtensa@linux-xtensa.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
- check that user TLB mappings correspond to the current page table;
- check that TLB mapping VPN is in the kernel/user address range
in accordance with its ASID.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
The virtual address of boot parameters chain is passed to the kernel via
a2 register. Adjust it in case it is remapped during MMUv3 -> MMUv2
mapping change, i.e. when it is in the first 128M.
Also fix interpretation of initrd and FDT addresses passed in the boot
parameters: these are physical addresses.
Cc: stable@vger.kernel.org
Reported-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Reused some code from a preliminary implementation by Max Fillippov.
Cc: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Chris Zankel <chris@zankel.net>
Pull slave-dmaengine updates from Vinod Koul:
"Once you have some time from extended weekend celebrations please
consider pulling the following to get:
- Various fixes and PCI driver for dw_dmac by Andy
- DT binding for imx-dma by Markus & imx-sdma by Shawn
- DT fixes for dmaengine by Lars
- jz4740 dmac driver by Lars
- and various fixes across the drivers"
What "extended weekend celebrations"? I'm in the merge window, who has
time for extended celebrations..
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
DMA: shdma: add DT support
DMA: shdma: shdma_chan_filter() has to be in shdma-base.h
DMA: shdma: (cosmetic) don't re-calculate a pointer
dmaengine: at_hdmac: prepare clk before calling enable
dmaengine/trivial: at_hdmac: add curly brackets to if/else expressions
dmaengine: at_hdmac: remove unsuded atc_cleanup_descriptors()
dmaengine: at_hdmac: add FIFO configuration parameter to DMA DT binding
ARM: at91: dt: add header to define at_hdmac configuration
MIPS: jz4740: Correct clock gate bit for DMA controller
MIPS: jz4740: Remove custom DMA API
MIPS: jz4740: Register jz4740 DMA device
dma: Add a jz4740 dmaengine driver
MIPS: jz4740: Acquire and enable DMA controller clock
dma: mmp_tdma: disable irq when disabling dma channel
dmaengine: PL08x: Avoid collisions with get_signal() macro
dmaengine: dw: select DW_DMAC_BIG_ENDIAN_IO automagically
dma: dw: add PCI part of the driver
dma: dw: split driver to library part and platform code
dma: move dw_dmac driver to an own directory
dw_dmac: don't check resource with devm_ioremap_resource
...
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
Pull ARM DMA mapping updates from Marek Szyprowski:
"This contains important bugfixes and an update for IOMMU integration
support for ARM architecture"
* 'for-v3.11' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma: Drop __GFP_COMP for iommu dma memory allocations
ARM: DMA-mapping: mark all !DMA_TO_DEVICE pages in unmapping as clean
ARM: dma-mapping: NULLify dev->archdata.mapping pointer on detach
ARM: dma-mapping: convert DMA direction into IOMMU protection attributes
ARM: dma-mapping: Get pages if the cpu_addr is out of atomic_pool
- Infrastructure and DT files for TZ1090 SoC (pin control drivers
already merged via pinctrl tree).
- Panic on boot instead of just warning if cache aliasing possible.
- Various SMP/hotplug fixes.
- Various other randconfig/sparse fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=nmbJ
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull Metag architecture changes from James Hogan:
- Infrastructure and DT files for TZ1090 SoC (pin control drivers
already merged via pinctrl tree).
- Panic on boot instead of just warning if cache aliasing possible.
- Various SMP/hotplug fixes.
- Various other randconfig/sparse fixes.
* tag 'metag-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (24 commits)
metag: move EXPORT_SYMBOL(csum_partial) to metag_ksyms.c
metag: cpu hotplug: route_irq: preserve irq mask
metag: kick: add missing irq_enter/exit to kick_handler()
metag: smp: don't spin waiting for CPU to start
metag: smp: enable irqs after set_cpu_online
metag: use clear_tasks_mm_cpumask()
metag: tz1090: select and instantiate pinctrl-tz1090-pdc
metag: tz1090: select and instantiate pinctrl-tz1090
metag: don't check for cache aliasing on smp cpu boot
metag: panic if cache aliasing possible
metag: *.dts: include using preprocessor
metag: add <dt-bindings/> symlink
metag/.gitignore: Extend the *.dtb pattern to match the dtb.S files
metag/traps: include setup.h for the per_cpu_trap_init declaration
metag/traps: Mark die() as __noreturn to match the declaration.
metag/processor.h: Add missing cpuinfo_op declaration.
metag/setup: Restrict scope for the capabilities variable
metag/mm/cache: Restrict scope for metag_lnkget_probe
metag/asm/irq.h: Declare init_IRQ
metag/kernel/irq.c: Declare root_domain as static
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=XQbF
-----END PGP SIGNATURE-----
Merge tag 'xenarm-for-3.11-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen
Pull Xen ARM update rom Stefano Stabellini:
"Just one commit this time: the implementation of the tmem hypercall
for arm and arm64"
* tag 'xenarm-for-3.11-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen:
xen/arm and xen/arm64: implement HYPERVISOR_tmem_op
This is the long awaited simplification of irqdomain. It gets rid of the
different types of irq domains and instead both linear and tree mappings
can be supported in a single domain. Doing this removes a lot of special
case code and makes irq domains simpler to understand overall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yJRw
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux
Pull irqdomain refactoring from Grant Likely:
"This is the long awaited simplification of irqdomain. It gets rid of
the different types of irq domains and instead both linear and tree
mappings can be supported in a single domain. Doing this removes a
lot of special case code and makes irq domains simpler to understand
overall"
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
irq: fix checkpatch error
irqdomain: Include hwirq number in /proc/interrupts
irqdomain: make irq_linear_revmap() a fast path again
irqdomain: remove irq_domain_generate_simple()
irqdomain: Refactor irq_domain_associate_many()
irqdomain: Beef up debugfs output
irqdomain: Clean up aftermath of irq_domain refactoring
irqdomain: Eliminate revmap type
irqdomain: merge linear and tree reverse mappings.
irqdomain: Add a name field
irqdomain: Replace LEGACY mapping with LINEAR
irqdomain: Relax failure path on setting up mappings
With the new linux/reboot.h header file dependency added, we can no
longer build ixp4xx. The easiest way to avoid that is to remove the
inclusion of mach/hardware.h from mach/timex.h, which does not need
that header anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Jason Cooper <jason@lakedaemon.net>
Some OMAP SoCs use this function while others do not, and that
causes a warning when building multi_v7_defconfig. Marking the
function __maybe_unused silences the harmless warning without the
need to add complex #ifdef logic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
If we build a kernel with CONFIG_ARCH_OMAP2PLUS enabled but all of the
individual SoCs disabled, we run into a large number of link errors
because if incorrect dependencies:
arch/arm/mach-omap2/built-in.o: In function `_add_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:691: undefined reference to `clkdm_add_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_del_initiator_dep':
arch/arm/mach-omap2/omap_hwmod.c:720: undefined reference to `clkdm_del_sleepdep' arch/arm/mach-omap2/built-in.o: In function `_enable':
arch/arm/mach-omap2/omap_hwmod.c:2145: undefined reference to `clkdm_in_hwsup'
arch/arm/mach-omap2/omap_hwmod.c:2147: undefined reference to `clkdm_hwmod_enable'
arch/arm/mach-omap2/omap_hwmod.c:2191: undefined reference to `clkdm_hwmod_disable'
arch/arm/mach-omap2/omap_hwmod.c:2146: undefined reference to `clkdm_missing_idle_reporting' arch/arm/mach-omap2/built-in.o: In function `_idle':
arch/arm/mach-omap2/omap_hwmod.c:2235: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `_shutdown':
arch/arm/mach-omap2/omap_hwmod.c:2338: undefined reference to `clkdm_hwmod_disable' arch/arm/mach-omap2/built-in.o: In function `omap_hwmod_get_context_loss_count':
arch/arm/mach-omap2/omap_hwmod.c:4071: undefined reference to `pwrdm_get_context_loss_count' arch/arm/mach-omap2/built-in.o: In function `omap_pm_clkdms_setup':
arch/arm/mach-omap2/pm.c:114: undefined reference to `clkdm_allow_idle'
arch/arm/mach-omap2/pm.c:117: undefined reference to `clkdm_sleep' arch/arm/mach-omap2/built-in.o: In function `omap2_common_pm_late_init':
arch/arm/mach-omap2/pm.c:294: undefined reference to `omap_voltage_late_init' arch/arm/mach-omap2/built-in.o: In function `omap2_gpio_dev_init':
arch/arm/mach-omap2/gpio.c:133: undefined reference to `pwrdm_can_ever_lose_context'
We can avoid this if we make CONFIG_ARCH_OMAP2PLUS a silent option that
gets enabled any time that one of the SoC versions is enabled.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The zynq platform code only supports DT based booting, so we
should use DT_MACHINE_START rather than MACHINE_START.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Simek <michal.simek@xilinx.com>
These are selected by omap4 but used in common omap4/5
SMP code, so building an omap5-only kernel is actually
broken without this patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Add SDHCI driver for the Broadcom 281xx SoCs.
Still missing:
- power managemement
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
As Linus said its not an error to not have an AMD IOMMU; esp.
when you're not even running on an AMD platform.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Link: http://lkml.kernel.org/r/20130703075542.GF23916@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that all users of the custom jz4740 DMA API have been converted to use
the dmaengine API instead we can remove the custom API and move all the code
talking to the hardware to the dmaengine driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Previously, it was assumed that the DMA controller clock is not gated
when the kernel starts running. While that is the power-on state, it is
safer to not rely on that.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As pointed out by Arnd Bergmann there is a get_signal macro definied in
linux/signal.h which can conflict with the platform data callback
function of the same name leading to confusing errors from the compiler
(especially if signal.h manages to get pulled into the driver itself due
to header dependencies). Avoid such errors by renaming get_signal and
put_signal in the platform data to get_xfer_signal and put_xfer_signal.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some during
this cycle, but even going though my tree isn't a great fit. Ian
Campbell has prototyped splitting the bindings and .dtb files into a
separate repository. The plan is to migrate to using that sometime in
the next few kernel releases which should get rid of a lot of the churn
on binding docs and .dts files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CndB
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some
during this cycle, but even going though my tree isn't a great fit.
Ian Campbell has prototyped splitting the bindings and .dtb files into
a separate repository. The plan is to migrate to using that sometime
in the next few kernel releases which should get rid of a lot of the
churn on binding docs and .dts files"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of: Fix address decoding on Bimini and js2x machines
of: remove CONFIG_OF_DEVICE
usb: chipidea: depend on CONFIG_OF instead of CONFIG_OF_DEVICE
of: remove of_platform_driver
ibmebus: convert of_platform_driver to platform_driver
driver core: move to_platform_driver to platform_device.h
mfd: DT bindings for the palmas family MFD
ARM: dts: omap3-devkit8000: fix NAND memory binding
of/base: fix typos
of: remove #ifdef from linux/of_platform.h
Pull input updates from Dmitry Torokhov:
"First round of updates for the input subsystem.
You will get a new touchsreen driver for Cypress 4th generation
devices, a driver for a special controller implementing PS/2 protocol
in OLPC devices, and a driver for power key for SiRFprimaII PWRC.
HID and bcm5497 now support for the 2013 MacBook Air.
EVIOCGKEY and the rest of evdev ioctls now flush events of matching
type from the client's event queue so that clients can be sure any
events received after issuing EVIOCG* ioctl are new events.
And a host of cleanups and improvements in other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: cyttsp4 - kfree xfer_buf on error path in probe()
Input: tps6507x-ts - select INPUT_POLLDEV
Input: bcm5974 - add support for the 2013 MacBook Air
HID: apple: Add support for the 2013 Macbook Air
Input: cyttsp4 - leak on error path in probe()
Input: cyttsp4 - silence NULL dereference warning
Input: cyttsp4 - silence shift wrap warning
Input: tps6507x-ts - convert to polled input device infrastructure
ARM: davinci: da850-evm: remove vref from touchscreen platform data
Input: cyttsp4 - SPI driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - I2C driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - add core driver for Cypress TMA4XX touchscreen devices
Input: cyttsp - I2C driver split into two modules
Input: add OLPC AP-SP driver
Input: nspire-keypad - remove redundant dev_err call in nspire_keypad_probe()
Input: tps6507x-ts - remove vref from platform data
Input: tps6507x-ts - use bool for booleans
Input: tps6507x-ts - remove bogus unreachable code
Input: samsung-keypad - let device core setup the default pin configuration
Input: wacom_i2c - implement hovering capability
...
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into timers/core
Frederic sayed: "Most of these patches have been hanging around for
several month now, in -mmotm for a significant chunk. They already
missed a few releases."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull i2c updates from Wolfram Sang:
- new drivers: Kontron PLD, Wondermedia VT
- mv64xxx driver gained sun4i support and a bigger cleanup
- duplicate driver 'intel-mid' removed
- added generic device tree binding for sda holding time (and
designware driver already uses it)
- we tried to allow driver probing with only device tree and no i2c
ids, but I had to revert it because of side effects. Needs some
rethinking.
- driver bugfixes, cleanups...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c-designware: use div_u64 to fix link
i2c: Kontron PLD i2c bus driver
i2c: iop3xxx: fix build failure after waitqueue changes
i2c-designware: make SDA hold time configurable
i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided
i2c: imx: allow autoloading on dt ids
i2c: mv64xxx: Fix transfer error code
i2c: i801: SMBus patch for Intel Coleto Creek DeviceIDs
i2c: omap: correct usage of the interrupt enable register
i2c-pxa: prepare clock before use
Revert "i2c: core: make it possible to match a pure device tree driver"
i2c: nomadik: allocate adapter number dynamically
i2c: nomadik: support elder Nomadiks
i2c: mv64xxx: Add Allwinner sun4i compatible
i2c: mv64xxx: make the registers offset configurable
i2c: mv64xxx: Add macros to access parts of registers
i2c: vt8500: Add support for I2C bus on Wondermedia SoCs
i2c: designware: fix race between subsequent xfers
i2c: bfin-twi: Read and write the FIFO in loop
i2c: core: make it possible to match a pure device tree driver
...
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Merge Kconfig menu diet patches from Dave Hansen:
"I think the "Kernel Hacking" menu has gotten a bit out of hand. It is
over 120 lines long on my system with everything enabled and options
are scattered around it haphazardly.
http://sr71.net/~dave/linux/kconfig-horror.png
Let's try to introduce some sanity. This set takes that 120 lines
down to 55 and makes it vastly easier to find some things. It's a
start.
This set stands on its own, but there is plenty of room for follow-up
patches. The arch-specific debug options still end up getting stuck
in the top-level "kernel hacking" menu. OPTIMIZE_INLINING, for
instance, could obviously go in to the "compiler options" menu, but
the fact that it is defined in arch/ in a separate Kconfig file keeps
it on its own for the moment.
The Signed-off-by's in here look funky. I changed employers while
working on this set, so I have signoffs from both email addresses"
* emailed patches from Dave Hansen <dave@sr71.net>:
hang and lockup detection menu
kconfig: consolidate printk options
group locking debugging options
consolidate compilation option configs
consolidate runtime testing configs
order memory debugging Kconfig options
consolidate per-arch stack overflow debugging options
Original posting:
http://lkml.kernel.org/r/20121214184202.F54094D9@kernel.stglabs.ibm.com
Several architectures have similar stack debugging config options.
They all pretty much do the same thing, some with slightly
differing help text.
This patch changes the architectures to instead enable a Kconfig
boolean, and then use that boolean in the generic Kconfig.debug
to present the actual menu option. This removes a bunch of
duplication and adds consistency across arches.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [for tile]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc changes for the 3.11 merge window. In addition to
the usual bug fixes and small updates, the main highlights are:
- Support for transparent huge pages by Aneesh Kumar for 64-bit
server processors. This allows the use of 16M pages as transparent
huge pages on kernels compiled with a 64K base page size.
- Base VFIO support for KVM on power by Alexey Kardashevskiy
- Wiring up of our nvram to the pstore infrastructure, including
putting compressed oopses in there by Aruna Balakrishnaiah
- Move, rework and improve our "EEH" (basically PCI error handling
and recovery) infrastructure. It is no longer specific to pseries
but is now usable by the new "powernv" platform as well (no
hypervisor) by Gavin Shan.
- I fixed some bugs in our math-emu instruction decoding and made it
usable to emulate some optional FP instructions on processors with
hard FP that lack them (such as fsqrt on Freescale embedded
processors).
- Support for Power8 "Event Based Branch" facility by Michael
Ellerman. This facility allows what is basically "userspace
interrupts" for performance monitor events.
- A bunch of Transactional Memory vs. Signals bug fixes and HW
breakpoint/watchpoint fixes by Michael Neuling.
And more ... I appologize in advance if I've failed to highlight
something that somebody deemed worth it."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
pstore: Add hsize argument in write_buf call of pstore_ftrace_call
powerpc/fsl: add MPIC timer wakeup support
powerpc/mpic: create mpic subsystem object
powerpc/mpic: add global timer support
powerpc/mpic: add irq_set_wake support
powerpc/85xx: enable coreint for all the 64bit boards
powerpc/8xx: Erroneous double irq_eoi() on CPM IRQ in MPC8xx
powerpc/fsl: Enable CONFIG_E1000E in mpc85xx_smp_defconfig
powerpc/mpic: Add get_version API both for internal and external use
powerpc: Handle both new style and old style reserve maps
powerpc/hw_brk: Fix off by one error when validating DAWR region end
powerpc/pseries: Support compression of oops text via pstore
powerpc/pseries: Re-organise the oops compression code
pstore: Pass header size in the pstore write callback
powerpc/powernv: Fix iommu initialization again
powerpc/pseries: Inform the hypervisor we are using EBB regs
powerpc/perf: Add power8 EBB support
powerpc/perf: Core EBB support for 64-bit book3s
powerpc/perf: Drop MMCRA from thread_struct
powerpc/perf: Don't enable if we have zero events
...
Some userspaces do not preserve unusable property. Since usable
segment has to be present according to VMX spec we can use present
property to amend userspace bug by making unusable segment always
nonpresent. vmx_segment_access_rights() already marks nonpresent segment
as unusable.
Cc: stable@vger.kernel.org # 3.9+
Reported-by: Stefan Pietsch <stefan.pietsch@lsexperts.de>
Tested-by: Stefan Pietsch <stefan.pietsch@lsexperts.de>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Finally plug KVM/arm64 into the config system, making it possible
to enable KVM support on AArch64 CPUs.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As this config must support boards which cannot support separate device
trees, enable support for appended ones.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Build EDMA in by default to avoid fewer people stepping on their toes
with broken DMA on drivers needing EDMA.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make DRA752 thermal support enabled on omap2plus_defconfig
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Platform code used to depend on bootloadres for correctly setting the mux
pin modes. But bootloaders should only set the minimum required mux pins.
So, DSS mux pins are not set in U-Boot anymore and video display is broken
on IGEPv2 when booting with newer U-Boot versions.
Setup the DSS pin muxes to enable display functionality.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We still need video & sound drivers with device tree enabled.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cocci spatch "ptr_ret.spatch"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP runtime PM implementation was removed in v3.0. But one Makefile
line, which was used to tweak CFLAGS, was overlooked. Remove it too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM errata 798181 is applicable for OMAP5 based devices. So enable
the same in the build. Errata extract and workaround information
is as below.
On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
adequately shooting down all use of the old entries. The
ARM_ERRATA_798181 option enables the Linux kernel workaround
for this erratum which sends an IPI to the CPUs that are running
the same ASID as the one being invalidated.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On platforms such as Cortex-A15 based OMAP5, SCU is not used, however
since much code is shared between Cortex-A9 based OMAP4 (which uses
SCU) and OMAP5, It does help to have inline functions returning error
values when SCU is not present on the platform.
arch/arm/mach-omap2/omap-smp.c which is common between OMAP4 and 5
handles the SCU usage only for OMAP4.
This fixes the following build failure with OMAP5 only build:
arch/arm/mach-omap2/built-in.o: In function `omap4_smp_init_cpus':
arch/arm/mach-omap2/omap-smp.c:185: undefined reference to `scu_get_core_count'
arch/arm/mach-omap2/built-in.o: In function `omap4_smp_prepare_cpus':
arch/arm/mach-omap2/omap-smp.c:211: undefined reference to `scu_enable'
Reported-by: Pekon Gupta <pekon@ti.com>
Reported-by: Vincent Stehlé <v-stehle@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CPU sleep and resume functions for Cortex-A9 based OMAP4 and
Cortex-A15 based OMAP5 are different. Hence, even though we reuse
most of the remaining file as part of OMAP4/5 consolidation, build
OMAP4 specific sleep/resume operations only for OMAP4. SCU is not used
OMAP5.
This fixes the following build failure with OMAP5 only build:
arch/arm/mach-omap2/built-in.o: In function `scu_gp_set':
arch/arm/mach-omap2/sleep44xx.S:132: undefined reference to `scu_power_mode'
arch/arm/mach-omap2/built-in.o: In function `scu_gp_clear':
arch/arm/mach-omap2/sleep44xx.S:229: undefined reference to `scu_power_mode'
Reported-by: Pekon Gupta <pekon@ti.com>
Reported-by: Vincent Stehlé <v-stehle@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
of_property_read_string_index(...,&oh_name) in omap_dm_timer_init_one
does not alter the value of 'oh_name' even if the relevant function
fails and as 'oh_name' in stack may have a non-zero value, it would
be misunderstood by timer code that DT has specified "ti,hwmod"
property for timer. 'oh_name' in this scenario would be a junk value,
this would result in module not being enabled by hwmod API's for
timer, and in turn crash.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Jon Hunter <jgchunter@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move EXPORT_SYMBOL(csum_partial) from lib/checksum.c into metag_ksyms.c
so that it doesn't get omitted by the static linker if it's not used by
any other statically linked code, which can result in undefined symbols
when building modules.
For example a randconfig caused the following error:
ERROR: "csum_partial" [fs/reiserfs/reiserfs.ko] undefined!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Pull LED subsystem updates from Bryan Wu:
- lp55xx device tree updates
- mc13xxx driver updates
- some clean up
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: mc13783: Fix "uninitialized variable" warning
leds: Convert led class driver from legacy pm ops to dev_pm_ops
leds: leds-mc13783: Add MC13892 LED support
leds: leds-mc13783: Prepare driver to support MC13892 LEDs
leds: renesas-tpu: cleanup a small type issue
leds: use platform_{get,set}_drvdata()
leds: leds-gpio: Let device core handle pinctrl
leds: lp5562: Properly setup of_device_id table
leds: lp5523: Properly setup of_device_id table
leds: lp5521: Properly setup of_device_id table
leds: lp5562: support the device tree feature
leds: lp55xx: support dynamic channel settings in the device tree structure
leds: leds-ns2: remove unnecessary platform_set_drvdata()
leds: leds-mc13783: remove unnecessary platform_set_drvdata()
leds: leds-gpio: remove unnecessary platform_set_drvdata()
leds: atmel-pwm: remove unnecessary platform_set_drvdata()
leds: lp55xx: add support for Device Tree bindings
A relative calm release at this time with a flat diffstat.
The only significant change in the ALSA core side is the support for
more than 32 card instances, configurable via kconfig.
Other than that, in both ASoC and other parts, mostly some
improvements and fixes on the driver side.
- hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
- hda: Haswell HDMI audio fixes, runtime PM improvements
- hda: Intel BayTrail support, ALC5505 DSP support
- es1968: MediaForte M56VAP support
- usb-audio: Improved support for Yamaha/Roland devices
- usb-audio: M2Tech hiFace, Audio Advantage Micro II support
- hdspm: wordclock fixes
- ASoC: Pending fixes for WM8962
- ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
- ASoC: Generalisation of the Bluetooth and HDMI stub drivers
- ASoC: SSM2518 and RT5640 codec drivers.
- ASoC: Tegra CPUs with RT5640 machine driver
- ASoC: AC'97 refactoring bug fixes
- ASoC: ADAU1701 driver fixes
- Clean up of *_set_drvdata() in a wide range of drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=i5lT
-----END PGP SIGNATURE-----
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relative calm release at this time with a flat diffstat. The only
significant change in the ALSA core side is the support for more than
32 card instances, configurable via kconfig. Other than that, in both
ASoC and other parts, mostly some improvements and fixes on the driver
side.
- hda: More quirks for ALC269-variants on Dell & co, VIA codec fixes
- hda: Haswell HDMI audio fixes, runtime PM improvements
- hda: Intel BayTrail support, ALC5505 DSP support
- es1968: MediaForte M56VAP support
- usb-audio: Improved support for Yamaha/Roland devices
- usb-audio: M2Tech hiFace, Audio Advantage Micro II support
- hdspm: wordclock fixes
- ASoC: Pending fixes for WM8962
- ASoC: Cleanups and fixes for Blackfin, SGTL5000 and UX500
- ASoC: Generalisation of the Bluetooth and HDMI stub drivers
- ASoC: SSM2518 and RT5640 codec drivers.
- ASoC: Tegra CPUs with RT5640 machine driver
- ASoC: AC'97 refactoring bug fixes
- ASoC: ADAU1701 driver fixes
- Clean up of *_set_drvdata() in a wide range of drivers"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (284 commits)
ALSA: vmaster: Fix the regression of missing vmaster hook call
ALSA: hda - Add Dell SSID to support Headset Mic recording
ASoC: adau1701: remove control_data assignment
ASoC: adau1701: more direct regmap usage
ASoC: ac97: fixup multi-platform AC'97 module build failure
ASoC: pxa2xx: fixup multi-platform AC'97 build failures
ASoC: tegra20-ac97: Remove unused variable
ASoC: tegra20-ac97: Remove duplicate error message
ALSA: usb-audio: Add Audio Advantage Micro II
ASoC: tas5086: fix Mid-Z implementation
ASoC: tas5086: fix TAS5086_CLOCK_CONTROL register size
ALSA: Replace the magic number 44 with const
ALSA: hda - Fix the max length of control name in generic parser
ALSA: hda - Guess what, it's two more Dell headset mic quirks
ALSA: hda - Yet another Dell headset mic quirk
ALSA: hda - Add support for ALC5505 DSP power-save mode
ASoC: mfld: Remove unused variable
ALSA: usb-audio: add quirks for Roland QUAD/OCTO-CAPTURE
ALSA: usb-audio: claim autodetected PCM interfaces all at once
ALSA: usb-audio: remove superfluous Roland quirks
...
Pull libata updates from Tejun Heo:
"Overview of changes:
- The rest of maintainer email address updates.
- Some core updates - more robust default behavior for port
multipliers, better error reporting for SG_IO commands, and a way
to better work around now ancient and probably pretty rare PATA ->
SATA bridges with ATAPI devices.
- sata_rcar stabilization.
- Some hardware PCI ID additions and one-off low level driver
updates."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
AHCI: use ATA_BUSY
libata-zpodd: must use ata_tf_init()
ahci: AHCI-mode SATA patch for Intel Coleto Creek DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Coleto Creek DeviceIDs
libata: cleanup SAT error translation
ahci: sata: add support for exynos5440 sata
libata: skip SRST for all SIMG [34]7x port-multipliers
ahci: remove pmp link online check in FBS EH
sata highbank: add bit-banged SGPIO driver support
ahci: make ahci_transmit_led_message into a function pointer
sata_rcar: fix compilation warning in sata_rcar_thaw()
sata_highbank: increase retry count but shorten duration for Calxeda controller
ata: use pci_get_drvdata()
ipr: qc_fill_rtf() method should not store alternate status register
sata_rcar: add 'base' local variable to some functions
sata_rcar: correct 'sata_rcar_sht'
sata_rcar: kill superfluous code in sata_rcar_bmdma_fill_sg()
libata: do not limit R-Car SATA driver to shmobile
ata: use platform_{get,set}_drvdata()
AHCI: Make distinct names for ports in /proc/interrupts
...
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=X3Lo
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"
* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
PCI: Add CircuitCo vendor ID and subsystem ID
PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
PCI: Return early on allocation failures to unindent mainline code
PCI: Simplify IOV implementation and fix reference count races
PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
unicore32/PCI: Remove redundant call of pci_bus_add_devices()
m68k/PCI: Remove redundant call of pci_bus_add_devices()
PCI / ACPI / PM: Use correct power state strings in messages
PCI: Fix comment typo for pcie_pme_remove()
PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
PCI: Fix refcount issue in pci_create_root_bus() error recovery path
ia64/PCI: Clean up pci_scan_root_bus() usage
PCI/AER: Reset link for devices below Root Port or Downstream Port
ACPI / APEI: Force fatal AER severity when component has been reset
PCI/AER: Remove "extern" from function declarations
PCI/AER: Move AER severity defines to aer.h
PCI/AER: Set dev->__aer_firmware_first only for matching devices
PCI/AER: Factor out HEST device type matching
PCI/AER: Don't parse HEST table for non-PCIe devices
...
Add a configuration option to build RapidIO subsystem core code as a
loadable kernel module. Currently this option is available only for
x86-based platforms, with the additional patch for PowerPC planned to be
provided later.
This patch replaces kernel command line parameter "riohdid=" with its
module-specific analog "rapidio.hdid=".
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only user of saved_max_pfn in s390 is read_oldmem interface but we
have removed that interface, so saved_max_pfn is now unneeded in s390, and
we needn't set it anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only user of saved_max_pfn in ia64 is read_oldmem interface but we
have removed that interface, so saved_max_pfn is now unneeded in ia64, and
we needn't set it anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
saved_max_pfn is used to know the amount of memory that the previous
kernel used. And for powerpc, we set saved_max_pfn by passing the kernel
commandline parameter "savemaxmem=".
The only user of saved_max_pfn in powerpc is read_oldmem interface. Since
we have removed read_oldmem, we don't need this parameter anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
saved_max_pfn is used to know the amount of memory that the previous
kernel used. And for powerpc, we set saved_max_pfn by passing the kernel
commandline parameter "savemaxmem=".
The only user of saved_max_pfn in mips is read_oldmem interface. Since we
have removed read_oldmem, so we don't need this parameter anymore.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because it is not used.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On CSR SiRFprimaII/atlasVI, there is a programmable 16-bit divider
(RTC_DIV) that divides the input 32.768KHz clock to the frequency that
users need (E.g. 1 Hz). The divided real-time clock will be used to
drive a 32-bit counter (RTC_COUNTER) that provides users with the actual
time.
In each cycle of the divided real-time clock, there is a Hertz interrupt
generated to the RISC. Users can also configure an alarm (RTC_ALARM).
When RTC_COUNTER matches the alarm, there will be an alarm interrupt
generated to the RISC.
The system RTC can generate an alarm wake-up signal to notify the power
controller to wake up from power saving mode.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There have never been any real users of MEMSET operations since they
have been introduced in January 2007 by commit 7405f74bad ("dmaengine:
refactor dmaengine around dma_async_tx_descriptor"). Therefore remove
support for them for now, it can be always brought back when needed.
[sebastian.hesselbarth@gmail.com: fix drivers/dma/mv_xor]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'cmdline' is a NUL terminated string, when its length < 4, memcmp()
will cause memory access out of boundary.
So use strncmp() instead of memcmp().
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since die_if_kernel() is an extern common used function, better always
check the buffer length to avoid memory overflow by a long 'str'.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VALID_PAGE() has been removed from kernel long time ago,
so fix the comment.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VALID_PAGE() has been removed from kernel long time ago, so clean up it.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VALID_PAGE() has been removed from kernel long time ago, so clean up it.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VALID_PAGE() has been removed from kernel long time ago,
so fix the comment.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VALID_PAGE() has been removed from kernel long time ago, so clean up it.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Nadia Yvette Chambers <nyc@holomorphy.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now mem_init() for both Alpha UMA and Alpha NUMA are the same, so unify it
to reduce duplicated code.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for killing free_all_bootmem_node() by using free_all_bootmem().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: "Suzuki K. Poulose" <suzuki@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for killing free_all_bootmem_node() by using free_all_bootmem().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for killing free_all_bootmem_node() by using free_all_bootmem().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for killing free_all_bootmem_node() by using free_all_bootmem().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for killing free_all_bootmem_node() by using free_all_bootmem().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com> # for arch/arc
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prepare for removing num_physpages and simplify mem_init().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normalize global variables exported by vmlinux.lds to conform usage
guidelines from include/asm-generic/sections.h.
1) Use _text to mark the start of the kernel image including the head
text, and _stext to mark the start of the .text section.
2) Export mandatory global variables __bss_stop.
3) Adjust __init_begin and __init_end to avoid acrossing .text and
.data sections.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normalize global variables exported by vmlinux.lds to conform usage
guidelines from include/asm-generic/sections.h.
1) Use _text to mark the start of the kernel image including the head
text, and _stext to mark the start of the .text section.
2) Export mandatory global variables __init_begin and __init_end.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Generate mandatory global variables __bss_start/__bss_stop in
file vmlinux.lds.
Also remove one unused declaration of _text.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normalize global variables exported by vmlinux.lds to conform usage
guidelines from include/asm-generic/sections.h.
Use _text to mark the start of the kernel image including the head text,
and _stext to mark the start of the .text section.
This patch also fixes possible bugs due to current address layout that
[__init_begin, __init_end] is a sub-range of [_stext, _etext] and pages
within range [__init_begin, __init_end] will be freed by free_initmem().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normalize global variables exported by vmlinux.lds to conform usage
guidelines from include/asm-generic/sections.h.
Use _text to mark the start of the kernel image including the head text,
and _stext to mark the start of the .text section.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Concentrate code to modify totalram_pages into the mm core, so the arch
memory initialized code doesn't need to take care of it. With these
changes applied, only following functions from mm core modify global
variable totalram_pages: free_bootmem_late(), free_all_bootmem(),
free_all_bootmem_node(), adjust_managed_page_count().
With this patch applied, it will be much more easier for us to keep
totalram_pages and zone->managed_pages in consistence.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to simpilify management of totalram_pages and
zone->managed_pages, make __free_pages_bootmem() only available at boot
time. With this change applied, __free_pages_bootmem() will only be
used by bootmem.c and nobootmem.c at boot time, so mark it as __init.
Other callers of __free_pages_bootmem() have been converted to use
free_reserved_page(), which handles totalram_pages and
zone->managed_pages in a safer way.
This patch also fix a bug in free_pagetable() for x86_64, which should
increase zone->managed_pages instead of zone->present_pages when freeing
reserved pages.
And now we have managed_pages_count_lock to protect totalram_pages and
zone->managed_pages, so remove the redundant ppb_lock lock in
put_page_bootmem(). This greatly simplifies the locking rules.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit "mm: introduce new field 'managed_pages' to struct zone" assumes
that all highmem pages will be freed into the buddy system by function
mem_init(). But that's not always true, some architectures may reserve
some highmem pages during boot. For example PPC may allocate highmem
pages for giagant HugeTLB pages, and several architectures have code to
check PageReserved flag to exclude highmem pages allocated during boot
when freeing highmem pages into the buddy system.
So treat highmem pages in the same way as normal pages, that is to:
1) reset zone->managed_pages to zero in mem_init().
2) recalculate managed_pages when freeing pages into the buddy system.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Address more review comments from last round of code review.
1) Enhance free_reserved_area() to support poisoning freed memory with
pattern '0'. This could be used to get rid of poison_init_mem()
on ARM64.
2) A previous patch has disabled memory poison for initmem on s390
by mistake, so restore to the original behavior.
3) Remove redundant PAGE_ALIGN() when calling free_reserved_area().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change signature of free_reserved_area() according to Russell King's
suggestion to fix following build warnings:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:603:2: warning: passing argument 1 of 'free_reserved_area' makes integer from pointer without a cast [enabled by default]
free_reserved_area(__va(PHYS_PFN_OFFSET), swapper_pg_dir, 0, NULL);
^
In file included from include/linux/mman.h:4:0,
from arch/arm/mm/init.c:15:
include/linux/mm.h:1301:22: note: expected 'long unsigned int' but argument is of type 'void *'
extern unsigned long free_reserved_area(unsigned long start, unsigned long end,
mm/page_alloc.c: In function 'free_reserved_area':
>> mm/page_alloc.c:5134:3: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast [enabled by default]
In file included from arch/mips/include/asm/page.h:49:0,
from include/linux/mmzone.h:20,
from include/linux/gfp.h:4,
from include/linux/mm.h:8,
from mm/page_alloc.c:18:
arch/mips/include/asm/io.h:119:29: note: expected 'const volatile void *' but argument is of type 'long unsigned int'
mm/page_alloc.c: In function 'free_area_init_nodes':
mm/page_alloc.c:5030:34: warning: array subscript is below array bounds [-Warray-bounds]
Also address some minor code review comments.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the already existing interface huge_page_shift instead of h->order +
PAGE_SHIFT.
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The soft-dirty is a bit on a PTE which helps to track which pages a task
writes to. In order to do this tracking one should
1. Clear soft-dirty bits from PTEs ("echo 4 > /proc/PID/clear_refs)
2. Wait some time.
3. Read soft-dirty bits (55'th in /proc/PID/pagemap2 entries)
To do this tracking, the writable bit is cleared from PTEs when the
soft-dirty bit is. Thus, after this, when the task tries to modify a
page at some virtual address the #PF occurs and the kernel sets the
soft-dirty bit on the respective PTE.
Note, that although all the task's address space is marked as r/o after
the soft-dirty bits clear, the #PF-s that occur after that are processed
fast. This is so, since the pages are still mapped to physical memory,
and thus all the kernel does is finds this fact out and puts back
writable, dirty and soft-dirty bits on the PTE.
Another thing to note, is that when mremap moves PTEs they are marked
with soft-dirty as well, since from the user perspective mremap modifies
the virtual memory at mremap's new address.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need include "asm/uaccess.h" to pass compiling.
The related error (with allmodconfig):
arch/c6x/mm/init.c: In function `paging_init':
arch/c6x/mm/init.c:46:2: error: implicit declaration of function `set_fs' [-Werror=implicit-function-declaration]
arch/c6x/mm/init.c:46:9: error: `KERNEL_DS' undeclared (first use in this function)
arch/c6x/mm/init.c:46:9: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: <stable@vger.kernel.org> [3.10.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
On the x86 side, there are some optimizations and documentation updates.
The big ARM/KVM change for 3.11, support for AArch64, will come through
Catalin Marinas's tree. s390 and PPC have misc cleanups and bugfixes.
There is a conflict due to "s390/pgtable: fix ipte notify bit" having
entered 3.10 through Martin Schwidefsky's s390 tree. This pull request
has additional changes on top, so this tree's version is the correct one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=1zpG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"On the x86 side, there are some optimizations and documentation
updates. The big ARM/KVM change for 3.11, support for AArch64, will
come through Catalin Marinas's tree. s390 and PPC have misc cleanups
and bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (87 commits)
KVM: PPC: Ignore PIR writes
KVM: PPC: Book3S PR: Invalidate SLB entries properly
KVM: PPC: Book3S PR: Allow guest to use 1TB segments
KVM: PPC: Book3S PR: Don't keep scanning HPTEG after we find a match
KVM: PPC: Book3S PR: Fix invalidation of SLB entry 0 on guest entry
KVM: PPC: Book3S PR: Fix proto-VSID calculations
KVM: PPC: Guard doorbell exception with CONFIG_PPC_DOORBELL
KVM: Fix RTC interrupt coalescing tracking
kvm: Add a tracepoint write_tsc_offset
KVM: MMU: Inform users of mmio generation wraparound
KVM: MMU: document fast invalidate all mmio sptes
KVM: MMU: document fast invalidate all pages
KVM: MMU: document fast page fault
KVM: MMU: document mmio page fault
KVM: MMU: document write_flooding_count
KVM: MMU: document clear_spte_count
KVM: MMU: drop kvm_mmu_zap_mmio_sptes
KVM: MMU: init kvm generation close to mmio wrap-around value
KVM: MMU: add tracepoint for check_mmio_spte
KVM: MMU: fast invalidate all mmio sptes
...
* Fix memory leak when CPU hotplugging.
* Compile bugs with various #ifdefs
* Fix state changes in Xen PCI front not dealing well with new toolstack.
* Cleanups in code (use pr_*, fix 80 characters splits, etc)
* Long standing bug in double-reporting the steal time
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJR0Xc1AAoJEFjIrFwIi8fJo68H/jZaJJmytDI7exHTyq8fSGXQ
5OERw5YZeM5jZQG55YC5hmGS5oIpKEdBt+aAEpuofYUhrR/ZFqDr0j+QEiqC36bl
cl0/IAnMBGnyyO6FYY4Sut2H+S5BGYQNbwo9YAtgKtZANr2eLABxYUfMU44I/jCW
M7DAojME9OZLBW3ORYZTGf1A0T8hJINhxZIWhtLMrkckCb9AZMieKdMOHJEWq2jl
aPxx78U+2CLTdLquOLIiBEiTO3vAzx2Wt4prD+uCizWna45H9gBj7GFwBYH7p9Ry
TFyzmDc5PufThTilfDyQW1y4yiNLpFDC/67a1wpwObEBn87hstHgwHQQ5INzqwY=
=Ej7M
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.11-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Fix memory leak when CPU hotplugging.
- Compile bugs with various #ifdefs
- Fix state changes in Xen PCI front not dealing well with new
toolstack.
- Cleanups in code (use pr_*, fix 80 characters splits, etc)
- Long standing bug in double-reporting the steal time
* tag 'stable/for-linus-3.11-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/time: remove blocked time accounting from xen "clockchip"
xen: Convert printks to pr_<level>
xen: ifdef CONFIG_HIBERNATE_CALLBACKS xen_*_suspend
xen/pcifront: Deal with toolstack missing 'XenbusStateClosing' state.
xen/time: Free onlined per-cpu data structure if we want to online it again.
xen/time: Check that the per_cpu data structure has data before freeing.
xen/time: Don't leak interrupt name when offlining.
xen/time: Encapsulate the struct clock_event_device in another structure.
xen/spinlock: Don't leak interrupt name when offlining.
xen/smp: Don't leak interrupt name when offlining.
xen/smp: Set the per-cpu IRQ number to a valid default.
xen/smp: Introduce a common structure to contain the IRQ name and interrupt line.
xen/smp: Coalesce the free_irq calls in one function.
xen-pciback: fix error return code in pcistub_irq_handler_switch()
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vZYj
-----END PGP SIGNATURE-----
mergetag object b3087e48ce
type commit
tag virtio-next-for-linus
tagger Rusty Russell <rusty@rustcorp.com.au> 1372639977 +0930
Was away, but it's all trivial and been sitting in linux-next. So if you don't
pull, no electrons will be harmed.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=p6z7
-----END PGP SIGNATURE-----
Merge tags 'modules-next-for-linus' and 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull trivial module and virtio fixes from Rusty Russell.
Apparently these were meant for 3.10, but came in after the release.
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modpost.c: Add .text.unlikely to TEXT_SECTIONS
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio: remove virtqueue_add_buf().
lguest: rename i386_head.S
virtio_blk: Add missing 'static' qualifiers
virtio: console: Add emergency writeonly register to config space
virtio_pci: better macro exported in uapi
across several different platforms and architectures, fixes to existing
drivers, a MAINTAINERS file fix and improvements to the basic clock
types that allow them to be of use to more platforms than before. Only a
few fixes to the core framework are included with most all of the
changes landing in the various clock drivers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=SwMB
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux
Pull clock framework updates from Mike Turquette:
"The common clock framework changes for 3.11 include new clock drivers
across several different platforms and architectures, fixes to
existing drivers, a MAINTAINERS file fix and improvements to the basic
clock types that allow them to be of use to more platforms than before.
Only a few fixes to the core framework are included with most all of
the changes landing in the various clock drivers themselves."
* tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux: (55 commits)
clk: tegra: fix ifdef for tegra_periph_reset_assert inline
clk: tegra: provide tegra_periph_reset_assert alternative
clk: exynos4: Fix clock aliases for cpufreq related clocks
clk: samsung: Add MUX_FA macro to pass flag and alias
clk: add support for Rockchip gate clocks
clk: vexpress: Make the clock drivers directly available for arm64
clk: vexpress: Use full node name to identify individual clocks
clk: tegra: T114: add DFLL DVCO reset control
clk: tegra: T114: add DFLL source clocks
clk: tegra: T114: add FCPU clock shaper programming, needed by the DFLL
clk: gate: add CLK_GATE_HIWORD_MASK
clk: divider: add CLK_DIVIDER_HIWORD_MASK flag
clk: mux: add CLK_MUX_HIWORD_MASK
clk: Always notify whole subtree when reparenting
MAINTAINERS: make drivers/clk entry match subdirs
clk: honor CLK_GET_RATE_NOCACHE in clk_set_rate
clk: use clk_get_rate() for debugfs
clk: tegra: Use override bits when needed
clk: tegra: override bits for Tegra30 PLLM
clk: tegra: override bits for Tegra114 PLLM
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Dm06
-----END PGP SIGNATURE-----
Merge tag 'please-pull-mce-therm' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull thermal power-limit update from Tony Luck:
"Thermal limit warnings are too scary and cause unnecessary concern"
* tag 'please-pull-mce-therm' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
x86 thermal: Disable power limit notification interrupt by default
x86 thermal: Delete power-limit-notification console messages
Pull "exotic" arch fixes from Geert Uytterhoeven:
"This is a collection of several exotic architecture fixes, and a few
other fixes for issues that were detected while doing the former"
* 'exotic-arch-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (35 commits)
lib: Move fonts from drivers/video/console/ to lib/fonts/
console/font: Refactor font support code selection logic
Revert "staging/solo6x10: depend on CONFIG_FONTS"
input: cros_ec_keyb_clear_keyboard() depends on CONFIG_PM_SLEEP
score: Wire up asm-generic/xor.h
score: Remove unneeded <asm/dma-mapping.h>
openrisc: Wire up asm-generic/xor.h
h8300/boot: Use POSIX "$((..))" instead of bashism "$[...]"
h8300: Mark H83002 and H83048 CPU support broken
h8300: Switch h8300 to drivers/Kconfig
h8300: Limit timer channel ranges in Kconfig
h8300: Wire up asm-generic/xor.h
h8300: Fill the system call table using a CALL() macro
h8300: Fix <asm/tlb.h>
h8300: Hardcode symbol prefixes in asm sources
h8300: add missing definition for read_barries_depends()
frv: head.S - Remove commented-out initialization code
cris: Wire up asm-generic/vga.h
parport: disable PC-style parallel port support on cris
console: Disable VGA text console support on cris
...
Pull m68k updates from Geert Uytterhoeven.
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/q40: Enable PC parallel port in defconfig
m68k/q40: Undefine insl/outsl before redefining them
m68k/uaccess: Fix asm constraints for userspace access
swim: Release memory region after incorrect return/goto
m68k/irq: Vector ints need a valid interrupt handler
m68k/math-emu: unsigned issue, 'unsigned long' will never be less than zero
m68k: remove CONFIG_EARLY_PRINTK dependency on CONFIG_EMBEDDED, default to n
m68k/sun3: remove inline marking of EXPORT_SYMBOL functions
[SCSI] a3000: use module_platform_driver_probe()
[SCSI] a4000t: use module_platform_driver_probe()
m68k: Remove inline strcpy() and strcat() implementations
Highlights of changes:
-Continuation of ARC MM changes from 3.10 including
zero page optimization;
Setting pagecache pages dirty by default;
Non executable stack by default;
Reducing dcache flushes for aliasing VIPT config
-Long overdue rework of pt_regs machinery - removing the unused word gutters
and adding ECR register to baseline (helps cleanup lot of low level code)
-Support for ARC gcc 4.8
-Few other preventive fixes, cosmetics, usage of Kconfig helper..
The diffstat is larger than normal primarily because of arcregs.h header split
as well as beautification of macros in entry.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=65Fq
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.11-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull first batch of ARC changes from Vineet Gupta:
"There's a second bunch to follow next week - which depends on commits
on other trees (irq/net). I'd have preferred the accompanying ARC
change via respective trees, but it didn't workout somehow.
Highlights of changes:
- Continuation of ARC MM changes from 3.10 including
zero page optimization
Setting pagecache pages dirty by default
Non executable stack by default
Reducing dcache flushes for aliasing VIPT config
- Long overdue rework of pt_regs machinery - removing the unused word
gutters and adding ECR register to baseline (helps cleanup lot of
low level code)
- Support for ARC gcc 4.8
- Few other preventive fixes, cosmetics, usage of Kconfig helper..
The diffstat is larger than normal primarily because of arcregs.h
header split as well as beautification of macros in entry.h"
* tag 'arc-v3.11-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (32 commits)
ARC: warn on improper stack unwind FDE entries
arc: delete __cpuinit usage from all arc files
ARC: [tlb-miss] Fix bug with CONFIG_ARC_DBG_TLB_MISS_COUNT
ARC: [tlb-miss] Extraneous PTE bit testing/setting
ARC: Adjustments for gcc 4.8
ARC: Setup Vector Table Base in early boot
ARC: Remove explicit passing around of ECR
ARC: pt_regs update #5: Use real ECR for pt_regs->event vs. synth values
ARC: stop using pt_regs->orig_r8
ARC: pt_regs update #4: r25 saved/restored unconditionally
ARC: K/U SP saved from one location in stack switching macro
ARC: Entry Handler tweaks: Simplify branch for in-kernel preemption
ARC: Entry Handler tweaks: Avoid hardcoded LIMMS for ECR values
ARC: Increase readability of entry handlers
ARC: pt_regs update #3: Remove unused gutter at start of callee_regs
ARC: pt_regs update #2: Remove unused gutter at start of pt_regs
ARC: pt_regs update #1: Align pt_regs end with end of kernel stack page
ARC: pt_regs update #0: remove kernel stack canary
ARC: [mm] Remove @write argument to do_page_fault()
ARC: [mm] Make stack/heap Non-executable by default
...
Pull s390 updates from Martin Schwidefsky:
"This is the bulk of the s390 patches for the 3.11 merge window.
Notable enhancements are: the block timeout patches for dasd from
Hannes, and more work on the PCI support front. In addition some
cleanup and the usual bug fixing."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/dasd: Fail all requests when DASD_FLAG_ABORTIO is set
s390/dasd: Add 'timeout' attribute
block: check for timeout function in blk_rq_timed_out()
block/dasd: detailed I/O errors
s390/dasd: Reduce amount of messages for specific errors
s390/dasd: Implement block timeout handling
s390/dasd: process all requests in the device tasklet
s390/dasd: make number of retries configurable
s390/dasd: Clarify comment
s390/hwsampler: Updated misleading member names in hws_data_entry
s390/appldata_net_sum: do not use static data
s390/appldata_mem: do not use static data
s390/vmwatchdog: do not use static data
s390/airq: simplify adapter interrupt code
s390/pci: remove per device debug attribute
s390/dma: remove gratuitous brackets
s390/facility: decompose test_facility()
s390/sclp: remove duplicated include from sclp_ctl.c
s390/irq: store interrupt information in pt_regs
s390/drivers: Cocci spatch "ptr_ret.spatch"
...
- KVM and Xen ports to AArch64
- Hugetlbfs and transparent huge pages support for arm64
- Applied Micro X-Gene Kconfig entry and dts file
- Cache flushing improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=PZ/e
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 updates from Catalin Marinas:
"Main features:
- KVM and Xen ports to AArch64
- Hugetlbfs and transparent huge pages support for arm64
- Applied Micro X-Gene Kconfig entry and dts file
- Cache flushing improvements
For arm64 huge pages support, there are x86 changes moving part of
arch/x86/mm/hugetlbpage.c into mm/hugetlb.c to be re-used by arm64"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64: (66 commits)
arm64: Add initial DTS for APM X-Gene Storm SOC and APM Mustang board
arm64: Add defines for APM ARMv8 implementation
arm64: Enable APM X-Gene SOC family in the defconfig
arm64: Add Kconfig option for APM X-Gene SOC family
arm64/Makefile: provide vdso_install target
ARM64: mm: THP support.
ARM64: mm: Raise MAX_ORDER for 64KB pages and THP.
ARM64: mm: HugeTLB support.
ARM64: mm: Move PTE_PROT_NONE bit.
ARM64: mm: Make PAGE_NONE pages read only and no-execute.
ARM64: mm: Restore memblock limit when map_mem finished.
mm: thp: Correct the HPAGE_PMD_ORDER check.
x86: mm: Remove general hugetlb code from x86.
mm: hugetlb: Copy general hugetlb code from x86 to mm.
x86: mm: Remove x86 version of huge_pmd_share.
mm: hugetlb: Copy huge_pmd_share from x86 to mm.
arm64: KVM: document kernel object mappings in HYP
arm64: KVM: MAINTAINERS update
arm64: KVM: userspace API documentation
arm64: KVM: enable initialization of a 32bit vcpu
...
Pull ARM updates from Russell King:
"This contains the usual updates from other people (listed below) and
the usual random muddle of miscellaneous ARM updates which cover some
low priority bug fixes and performance improvements.
I've started to put the pull request wording into the merge commits,
which are:
- NoMMU stuff:
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I
were discussing today until we've reached a conclusion/that's had
some more review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now
that you've merged that. I've included the fix for limiting MPU to
CPU_V7.
- Huge page support
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
- LPAE updates
Please pull these miscellaneous LPAE fixes I've been collecting for
a while now for 3.11. They've been tested and reviewed by quite a
few people, and most of the patches are pretty trivial. -- Will Deacon.
- arch_timer cleanups
Please pull these arch_timer cleanups I've been holding onto for a
while. They're the same as my last posting, but have been rebased
to v3.10-rc3.
- mpidr linearisation (multiprocessor id register - identifies which
CPU number we are in the system)
This patch series that implements MPIDR linearization through a
simple hashing algorithm and updates current cpu_{suspend}/{resume}
code to use the newly created hash structures to retrieve context
pointers. It represents a stepping stone for the implementation of
power management code on forthcoming multi-cluster ARM systems.
It has been tested on TC2 (dual cluster A15xA7 system), iMX6q,
OMAP4 and Tegra, with processors hitting low-power states requiring
warm-boot resume through the cpu_resume code path"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: 7775/1: mm: Remove do_sect_fault from LPAE code
ARM: 7777/1: Avoid extra calls to the C compiler
ARM: 7774/1: Fix dtb dependency to use order-only prerequisites
ARM: 7770/1: remove residual ARMv2 support from decompressor
ARM: 7769/1: Cortex-A15: fix erratum 798181 implementation
ARM: 7768/1: prevent risks of out-of-bound access in ASID allocator
ARM: 7767/1: let the ASID allocator handle suspended animation
ARM: 7766/1: versatile: don't mark pen as __INIT
ARM: 7765/1: perf: Record the user-mode PC in the call chain.
ARM: 7735/2: Preserve the user r/w register TPIDRURW on context switch and fork
ARM: kernel: implement stack pointer save array through MPIDR hashing
ARM: kernel: build MPIDR hash function data structure
ARM: mpu: Ensure that MPU depends on CPU_V7
ARM: mpu: protect the vectors page with an MPU region
ARM: mpu: Allow enabling of the MPU via kconfig
ARM: 7758/1: introduce config HAS_BANDGAP
ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting
ARM: 7751/1: zImage: don't overwrite ourself with a page table
ARM: 7749/1: spinlock: retry trylock operation if strex fails on free lock
ARM: 7748/1: oabi: handle faults when loading swi instruction from userspace
...
Pull second set of VFS changes from Al Viro:
"Assorted f_pos race fixes, making do_splice_direct() safe to call with
i_mutex on parent, O_TMPFILE support, Jeff's locks.c series,
->d_hash/->d_compare calling conventions changes from Linus, misc
stuff all over the place."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
Document ->tmpfile()
ext4: ->tmpfile() support
vfs: export lseek_execute() to modules
lseek_execute() doesn't need an inode passed to it
block_dev: switch to fixed_size_llseek()
cpqphp_sysfs: switch to fixed_size_llseek()
tile-srom: switch to fixed_size_llseek()
proc_powerpc: switch to fixed_size_llseek()
ubi/cdev: switch to fixed_size_llseek()
pci/proc: switch to fixed_size_llseek()
isapnp: switch to fixed_size_llseek()
lpfc: switch to fixed_size_llseek()
locks: give the blocked_hash its own spinlock
locks: add a new "lm_owner_key" lock operation
locks: turn the blocked_list into a hashtable
locks: convert fl_link to a hlist_node
locks: avoid taking global lock if possible when waking up blocked waiters
locks: protect most of the file_lock handling with i_lock
locks: encapsulate the fl_link list handling
locks: make "added" in __posix_lock_file a bool
...
Commit 4c94c8b "ARM: tegra: update device trees for USB binding rework"
added regulator definitions for GPIO-controlled USB VBUS. However, none
of these contained the essential DT property enable-active-high. Add
this so that the regulator definitions are correct.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Correct GIO3 base addresses for EMEV2 SoC
- This bug bug added when GPIO support was added for the EMEV2 SoC
in v3.5
* Correct SCIFB0 resources for r8a77a4 SoC
- This was a bug was added when SCIF support was added for the r8a77a4 SoC
in v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+CUy
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM based SoC fixes for v3.11
* Correct GIO3 base addresses for EMEV2 SoC
- This bug bug added when GPIO support was added for the EMEV2 SoC
in v3.5
* Correct SCIFB0 resources for r8a77a4 SoC
- This was a bug was added when SCIF support was added for the r8a77a4 SoC
in v3.10
* tag 'renesas-fixes-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: emev2 GIO3 resource fix
ARM: shmobile: r8a73a4: Fix resources for SCIFB0
This updates multi_v7_defconfig to boot on at least Tegra2 Seaboard and
Panda ES. I lack working hardware for most of the platforms that were
enabled to compare with, so I could only verify those two for now. Still,
I enabled all of the available ones for build coverage purposes.
Beyond base platforms, things like PRINTK_TIME, filesystems, MMC, USB,
INET and UNIX networking was enabled. I'm sure we'll keep adding more
over time, but this gets us off the ground for semi-regular boot testing.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull x86 UV update from Ingo Molnar:
"There's a single commit in this tree, which adds support for a new SGI
UV GRU (Global Reference Unit - fast NUMA messaging ASIC) hardware
feature to scale up and beyond: an optional distributed mode that will
allow per-node address mapping of local GRU space, as opposed to
mapping all GRU hardware to the same contiguous high space"
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/UV: Add GRU distributed mode mappings
Pull x86 tracing updates from Ingo Molnar:
"This tree adds IRQ vector tracepoints that are named after the handler
and which output the vector #, based on a zero-overhead approach that
relies on changing the IDT entries, by Seiji Aguchi.
The new tracepoints look like this:
# perf list | grep -i irq_vector
irq_vectors:local_timer_entry [Tracepoint event]
irq_vectors:local_timer_exit [Tracepoint event]
irq_vectors:reschedule_entry [Tracepoint event]
irq_vectors:reschedule_exit [Tracepoint event]
irq_vectors:spurious_apic_entry [Tracepoint event]
irq_vectors:spurious_apic_exit [Tracepoint event]
irq_vectors:error_apic_entry [Tracepoint event]
irq_vectors:error_apic_exit [Tracepoint event]
[...]"
* 'x86-tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tracing: Add config option checking to the definitions of mce handlers
trace,x86: Do not call local_irq_save() in load_current_idt()
trace,x86: Move creation of irq tracepoints from apic.c to irq.c
x86, trace: Add irq vector tracepoints
x86: Rename variables for debugging
x86, trace: Introduce entering/exiting_irq()
tracing: Add DEFINE_EVENT_FN() macro
Pull x86 RAS update from Ingo Molnar:
"The changes in this tree are:
- ACPI APEI (ACPI Platform Error Interface) improvements, by Chen
Gong
- misc MCE fixes/cleanups"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Update MCE severity condition check
mce: acpi/apei: Add comments to clarify usage of the various bitfields in the MCA subsystem
ACPI/APEI: Update einj documentation for param1/param2
ACPI/APEI: Add parameter check before error injection
ACPI, APEI, EINJ: Fix error return code in einj_init()
x86, mce: Fix "braodcast" typo
Pull x86 platform updates from Ingo Molnar:
"Two changes:
- A Kconfig dependency fix/cleanup
- Introduce the 'make kvmconfig' KVM configuration helper utility
that turns the current .config into a KVM-bootable config. Useful
for debugging specific native kernel configs that have no KVM
config options enabled on VM setups."
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform: Make X86_GOLDFISH depend on X86_EXTENDED_PLATFORM
x86/platform: Add kvmconfig to the phony targets
x86, platform, kvm, kconfig: Turn existing .config's into KVM-capable configs
Pull x86 mm changes from Ingo Molnar:
"Misc improvements:
- Fix /proc/mtrr reporting
- Fix ioremap printout
- Remove the unused pvclock fixmap entry on 32-bit
- misc cleanups"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioremap: Correct function name output
x86: Fix /proc/mtrr with base/size more than 44bits
ix86: Don't waste fixmap entries
x86/mm: Drop unneeded include <asm/*pgtable, page*_types.h>
x86_64: Correct phys_addr in cleanup_highmap comment
Pull x86 microcode loading update from Ingo Molnar:
"Two main changes that improve microcode loading on AMD CPUs:
- Add support for all-in-one binary microcode files that concatenate
the microcode images of multiple processor families, by Jacob Shin
- Add early microcode loading (embedded in the initrd) support, also
by Jacob Shin"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, amd: Another early loading fixup
x86, microcode, amd: Allow multiple families' bin files appended together
x86, microcode, amd: Make find_ucode_in_initrd() __init
x86, microcode, amd: Fix warnings and errors on with CONFIG_MICROCODE=m
x86, microcode, amd: Early microcode patch loading support for AMD
x86, microcode, amd: Refactor functions to prepare for early loading
x86, microcode: Vendor abstract out save_microcode_in_initrd()
x86, microcode, intel: Correct typo in printk
Pull x86 FPU changes from Ingo Molnar:
"There are two bigger changes in this tree:
- Add an [early-use-]safe static_cpu_has() variant and other
robustness improvements, including the new X86_DEBUG_STATIC_CPU_HAS
configurable debugging facility, motivated by recent obscure FPU
code bugs, by Borislav Petkov
- Reimplement FPU detection code in C and drop the old asm code, by
Peter Anvin."
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: Use static_cpu_has_safe before alternatives
x86: Add a static_cpu_has_safe variant
x86: Sanity-check static_cpu_has usage
x86, cpu: Add a synthetic, always true, cpu feature
x86: Get rid of ->hard_math and all the FPU asm fu
Pull x86 EFI changes from Ingo Molnar:
"Two fixes that should in principle increase robustness of our
interaction with the EFI firmware, and a cleanup"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: retry ExitBootServices() on failure
efi: Convert runtime services function ptrs
UEFI: Don't pass boot services regions to SetVirtualAddressMap()
Pull x86 debug update from Ingo Molnar:
"Misc debuggability improvements:
- Optimize the x86 CPU register printout a bit
- Expose the tboot TXT log via debugfs
- Small do_debug() cleanup"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tboot: Provide debugfs interfaces to access TXT log
x86: Remove weird PTR_ERR() in do_debug
x86/debug: Only print out DR registers if they are not power-on defaults
Pull x86 cpu updates from Ingo Molnar:
"Two changes:
- Extend 32-bit double fault debugging aid to 64-bit
- Fix a build warning"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/cacheinfo: Shut up last long-standing warning
x86: Extend #DF debugging aid to 64-bit
Pull x86 cleanups from Ingo Molnar:
"Misc x86 cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, reloc: Use xorl instead of xorq in relocate_kernel_64.S
x86, cleanups: Remove extra tab in __flush_tlb_one()
x86/mce: Remove check for CONFIG_X86_MCE_P4THERMAL
Pull x86 boot build fix from Ingo Molnar:
"Small fixlet for the build process"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Close opened file descriptor
Pull asm/x86 changes from Ingo Molnar:
"Misc changes, with a bigger processor-flags cleanup/reorganization by
Peter Anvin"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, asm, cleanup: Replace open-coded control register values with symbolic
x86, processor-flags: Fix the datatypes and add bit number defines
x86: Rename X86_CR4_RDWRGSFS to X86_CR4_FSGSBASE
x86, flags: Rename X86_EFLAGS_BIT1 to X86_EFLAGS_FIXED
linux/const.h: Add _BITUL() and _BITULL()
x86/vdso: Convert use of typedef ctl_table to struct ctl_table
x86: __force_order doesn't need to be an actual variable
Pull voluntary preemption fixes from Ingo Molnar:
"This tree contains a speedup which is achieved through better
might_sleep()/might_fault() preemption point annotations for uaccess
functions, by Michael S Tsirkin:
1. The only reason uaccess routines might sleep is if they fault.
Make this explicit for all architectures.
2. A voluntary preemption point in uaccess functions means compiler
can't inline them efficiently, this breaks assumptions that they
are very fast and small that e.g. net code seems to make. Remove
this preemption point so behaviour matches with what callers
assume.
3. Accesses (e.g through socket ops) to kernel memory with KERNEL_DS
like net/sunrpc does will never sleep. Remove an unconditinal
might_sleep() in the might_fault() inline in kernel.h (used when
PROVE_LOCKING is not set).
4. Accesses with pagefault_disable() return EFAULT but won't cause
caller to sleep. Check for that and thus avoid might_sleep() when
PROVE_LOCKING is set.
These changes offer a nice speedup for CONFIG_PREEMPT_VOLUNTARY=y
kernels, here's a network bandwidth measurement between a virtual
machine and the host:
before:
incoming: 7122.77 Mb/s
outgoing: 8480.37 Mb/s
after:
incoming: 8619.24 Mb/s [ +21.0% ]
outgoing: 9455.42 Mb/s [ +11.5% ]
I kept these changes in a separate tree, separate from scheduler
changes, because it's a mixed MM and scheduler topic"
* 'sched-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mm, sched: Allow uaccess in atomic with pagefault_disable()
mm, sched: Drop voluntary schedule from might_fault()
x86: uaccess s/might_sleep/might_fault/
tile: uaccess s/might_sleep/might_fault/
powerpc: uaccess s/might_sleep/might_fault/
mn10300: uaccess s/might_sleep/might_fault/
microblaze: uaccess s/might_sleep/might_fault/
m32r: uaccess s/might_sleep/might_fault/
frv: uaccess s/might_sleep/might_fault/
arm64: uaccess s/might_sleep/might_fault/
asm-generic: uaccess s/might_sleep/might_fault/
Pull scheduler updates from Ingo Molnar:
"The main changes:
- load-calculation cleanups and improvements, by Alex Shi
- various nohz related tidying up of statisics, by Frederic
Weisbecker
- factor out /proc functions to kernel/sched/proc.c, by Paul
Gortmaker
- simplify the RT policy scheduler, by Kirill Tkhai
- various fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
sched/debug: Remove CONFIG_FAIR_GROUP_SCHED mask
sched/debug: Fix formatting of /proc/<PID>/sched
sched: Fix typo in struct sched_avg member description
sched/fair: Fix typo describing flags in enqueue_entity
sched/debug: Add load-tracking statistics to task
sched: Change get_rq_runnable_load() to static and inline
sched/tg: Remove tg.load_weight
sched/cfs_rq: Change atomic64_t removed_load to atomic_long_t
sched/tg: Use 'unsigned long' for load variable in task group
sched: Change cfs_rq load avg to unsigned long
sched: Consider runnable load average in move_tasks()
sched: Compute runnable load avg in cpu_load and cpu_avg_load_per_task
sched: Update cpu load after task_tick
sched: Fix sleep time double accounting in enqueue entity
sched: Set an initial value of runnable avg for new forked task
sched: Move a few runnable tg variables into CONFIG_SMP
Revert "sched: Introduce temporary FAIR_GROUP_SCHED dependency for load-tracking"
sched: Don't mix use of typedef ctl_table and struct ctl_table
sched: Remove WARN_ON(!sd) from init_sched_groups_power()
sched: Fix memory leakage in build_sched_groups()
...
Pull perf updates from Ingo Molnar:
"Kernel improvements:
- watchdog driver improvements by Li Zefan
- Power7 CPI stack events related improvements by Sukadev Bhattiprolu
- event multiplexing via hrtimers and other improvements by Stephane
Eranian
- kernel stack use optimization by Andrew Hunter
- AMD IOMMU uncore PMU support by Suravee Suthikulpanit
- NMI handling rate-limits by Dave Hansen
- various hw_breakpoint fixes by Oleg Nesterov
- hw_breakpoint overflow period sampling and related signal handling
fixes by Jiri Olsa
- Intel Haswell PMU support by Andi Kleen
Tooling improvements:
- Reset SIGTERM handler in workload child process, fix from David
Ahern.
- Makefile reorganization, prep work for Kconfig patches, from Jiri
Olsa.
- Add automated make test suite, from Jiri Olsa.
- Add --percent-limit option to 'top' and 'report', from Namhyung
Kim.
- Sorting improvements, from Namhyung Kim.
- Expand definition of sysfs format attribute, from Michael Ellerman.
Tooling fixes:
- 'perf tests' fixes from Jiri Olsa.
- Make Power7 CPI stack events available in sysfs, from Sukadev
Bhattiprolu.
- Handle death by SIGTERM in 'perf record', fix from David Ahern.
- Fix printing of perf_event_paranoid message, from David Ahern.
- Handle realloc failures in 'perf kvm', from David Ahern.
- Fix divide by 0 in variance, from David Ahern.
- Save parent pid in thread struct, from David Ahern.
- Handle JITed code in shared memory, from Andi Kleen.
- Fixes for 'perf diff', from Jiri Olsa.
- Remove some unused struct members, from Jiri Olsa.
- Add missing liblk.a dependency for python/perf.so, fix from Jiri
Olsa.
- Respect CROSS_COMPILE in liblk.a, from Rabin Vincent.
- No need to do locking when adding hists in perf report, only 'top'
needs that, from Namhyung Kim.
- Fix alignment of symbol column in in the hists browser (top,
report) when -v is given, from NAmhyung Kim.
- Fix 'perf top' -E option behavior, from Namhyung Kim.
- Fix bug in isupper() and islower(), from Sukadev Bhattiprolu.
- Fix compile errors in bp_signal 'perf test', from Sukadev
Bhattiprolu.
... and more things"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (102 commits)
perf/x86: Disable PEBS-LL in intel_pmu_pebs_disable()
perf/x86: Fix shared register mutual exclusion enforcement
perf/x86/intel: Support full width counting
x86: Add NMI duration tracepoints
perf: Drop sample rate when sampling is too slow
x86: Warn when NMI handlers take large amounts of time
hw_breakpoint: Introduce "struct bp_cpuinfo"
hw_breakpoint: Simplify *register_wide_hw_breakpoint()
hw_breakpoint: Introduce cpumask_of_bp()
hw_breakpoint: Simplify the "weight" usage in toggle_bp_slot() paths
hw_breakpoint: Simplify list/idx mess in toggle_bp_slot() paths
perf/x86/intel: Add mem-loads/stores support for Haswell
perf/x86/intel: Support Haswell/v4 LBR format
perf/x86/intel: Move NMI clearing to end of PMI handler
perf/x86/intel: Add Haswell PEBS support
perf/x86/intel: Add simple Haswell PMU support
perf/x86/intel: Add Haswell PEBS record support
perf/x86/intel: Fix sparse warning
perf/x86/amd: AMD IOMMU Performance Counter PERF uncore PMU implementation
perf/x86/amd: Add IOMMU Performance Counter resource management
...
Pull core irq changes from Ingo Molnar:
"The main changes:
- generic-irqchip driver additions, cleanups and fixes
- 3 new irqchip drivers: ARMv7-M NVIC, TB10x and Marvell Orion SoCs
- irq_get_trigger_type() simplification and cross-arch cleanup
- various cleanups, simplifications
- documentation updates"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
softirq: Use _RET_IP_
genirq: Add the generic chip to the genirq docbook
genirq: generic-chip: Export some irq_gc_ functions
genirq: Fix can_request_irq() for IRQs without an action
irqchip: exynos-combiner: Staticize combiner_init
irqchip: Add support for ARMv7-M NVIC
irqchip: Add TB10x interrupt controller driver
irqdomain: Use irq_get_trigger_type() to get IRQ flags
MIPS: octeon: Use irq_get_trigger_type() to get IRQ flags
arm: orion: Use irq_get_trigger_type() to get IRQ flags
mfd: stmpe: use irq_get_trigger_type() to get IRQ flags
mfd: twl4030-irq: Use irq_get_trigger_type() to get IRQ flags
gpio: mvebu: Use irq_get_trigger_type() to get IRQ flags
genirq: Add irq_get_trigger_type() to get IRQ flags
genirq: Irqchip: document gcflags arg of irq_alloc_domain_generic_chips
genirq: Set irq thread to RT priority on creation
irqchip: Add support for Marvell Orion SoCs
genirq: Add kerneldoc for irq_disable.
genirq: irqchip: Add mask to block out invalid irqs
genirq: Generic chip: Add linear irq domain support
...
Pull WW mutex support from Ingo Molnar:
"This tree adds support for wound/wait style locks, which the graphics
guys would like to make use of in the TTM graphics subsystem.
Wound/wait mutexes are used when other multiple lock acquisitions of a
similar type can be done in an arbitrary order. The deadlock handling
used here is called wait/wound in the RDBMS literature: The older
tasks waits until it can acquire the contended lock. The younger
tasks needs to back off and drop all the locks it is currently
holding, ie the younger task is wounded.
See this LWN.net description of W/W mutexes:
https://lwn.net/Articles/548909/
The comments there outline specific usecases for this facility (which
have already been implemented for the DRM tree).
Also see Documentation/ww-mutex-design.txt for more details"
* 'core-mutexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking-selftests: Handle unexpected failures more strictly
mutex: Add more w/w tests to test EDEADLK path handling
mutex: Add more tests to lib/locking-selftest.c
mutex: Add w/w tests to lib/locking-selftest.c
mutex: Add w/w mutex slowpath debugging
mutex: Add support for wound/wait style locks
arch: Make __mutex_fastpath_lock_retval return whether fastpath succeeded or not
These are changes that arrived a little late before the merge
window or that have multiple dependencies on previous branches
so they did not fit into one of the earlier ones. There
are 10 branches merged here, a total of 39 non-merge commits.
Contents are a mixed bag for the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and
the TI 'Nspire' graphing calculator. These should have
been in the 'soc' branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos,
which is based on the other exynos branches to avoid
conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM
Conflicts:
* In Kconfig.debug, various additions trivially conflict,
the list should be kept in alphabetical order when
resolving.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUdLnl2CrR//JCVInAQIrKhAAwvtsGNe6j9nDuLEitWtQAmhHYZQyUJ8k
o9j/1j1CqhE8C0bLRud8D4m1GxfxbGeRm2d0HoNbxda3FmntUufqBDi6neMiQiLO
VltC5rOYL8Mday0Asc3SBfjBj8SZC2bypicKy5zUfzsObCBt343g1WvYffMDNmwH
FveOQK6q2BKmO67cazc9tk5xmxjVwP/LB8r5mQtiXmMguw0R+ZIDDIP6xaURFkxX
SAElleD2wtvpVHP1d6AKHpXN99u3xV3uoJjKljECEXdBzW/ZX8m7FG2tKY5xy368
ta0Nhh2MSRnBhUYOH9uah4PQWYEsbZ+M/W+3J9tKRu6q9D/c/AAxILyXUY2tcHNC
o1UwcUn1druirx3X1AW8HYAGNwW7BD3HANzIiUkQZG7ByfM4qCtUEo2SAFNIGBoR
v1FMLhMPgMWotZnKrDQQd0anxkKIOFaSMRVgpQLW2jQt/B7sHLmEH2yDffkbSD76
PQDThnW/dfm9dgeK+X4fPrveIMKbjQlbFz0okN+LPsUf8e1045HBgCi2A0lTIGWM
kVVgXHKKXi8G8HBa4VyDlORVHXk1bJEheF+zlDvdk4fHkcf+H/OfvFG2O9TdIdpb
ITXRyyteaRM4YIZpnJbzeeZDZXT89c2ah7xq36iM+L1ScidyntPquViXeasSc8r6
pKu9ZDc0Mow=
=cRu2
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Arnd Bergmann:
"These are changes that arrived a little late before the merge window
or that have multiple dependencies on previous branches so they did
not fit into one of the earlier ones. There are 10 branches merged
here, a total of 39 non-merge commits. Contents are a mixed bag for
the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and the TI
'Nspire' graphing calculator. These should have been in the 'soc'
branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos, which is based
on the other exynos branches to avoid conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: bail out on alien cpus
ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: stih41x: Add B2020 board support
ARM: stih41x: Add B2000 board support
ARM: sti: Add DEBUG_LL console support
ARM: sti: Add STiH416 SOC support
ARM: sti: Add STiH415 SOC support
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
...
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUdLnomCrR//JCVInAQJI/A/9FydsQa9sdnzLFgcdX5BeRRwkXLfDifCM
zDTfUBo+LriKOs7QHblmDg1MnY1UMB2IfrdHD0FsjK7WbZ/91EMAGDPYcI7Fu4+u
pGStxwWi2v+oCT1jjeOkCPT7hdCqogsSpybYq8itSb+zdvdOi6U35dWEKz8xGqz4
vTL9gTZbJP0kowkjIcaryk7FIj7BTIvMCW8n55JZEkDe0BuSJGYn5c3Mntut12ZK
5xM2PeNe2sd3dIdA6XbM2ye/XmYa8xY8Qu4/ijxfH1gnJLvz9Unp96nRXpEbIeMb
BH2Sro8dxsMCaweIQhSRKGnUWMYO/Rh7/+5EqzJ163Ezthx9nvHXJY2ndWuD7uM1
IcGrMxLtqP22TEMtZAVEATDp/5ymxEo5GM+eayUojQDn213wOJjRs5xz5IBsH4KM
8CM/gpadWmLjWku72yEV4lryLcdS0NVQzpTnEbILEGOU4u7qJtxRAp7x7tWBtFg8
4m/eWcSVk/U2SYbXmQHsfukuWgKY0cnZbctPcdnaqXwTP7toJEAK3gxoMtWh49Jq
2M2PVFyFejaaq5b/71wAJ7ePYw56H0N/F3RsGpPE55AY15++gSoQ+3t2Si68hDw8
NtyJMkQYpTvtqJbHXWpQQ3Zfs7pDBe01WDV7i+m4JTNggxUDaO/t1Fqp+fEksm4J
r+luEf5Gcgk=
=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
These changes from 30 individual branches for the most part update device
tree files, but there are also a few source code changes that have crept
in this time, usually in order to atomically move over a driver from
using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once.
There are a few conflicts with the other branches unfortunately:
* in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
from multiple branches. Need to be careful to have the right
set of closing braces as git gets this one wrong.
* In kirkwood.dtsi, one 'ranges' line got split into two lines, while
another line got added. Order of the lines does not matter.
* in sama5d3.dtsi, some cleanup was merged the wrong way, causing
a bogus conflict. We want the 'dmas' and 'dma-names' properties
to get added here.
* Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
* Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8PtJ
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
These are 18 branches on 9 platforms with board specific changes, mostly
for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the newer
machines, we get a few changes there as the result of drivers getting
enabled for those boards. This causes some conflicts with contents getting
added from multiple branches in sh-mobile specific files. Renesas is
putting a lot of work into migrating to device-tree based setup, which
will make all those files obsolete in the future and avoid both the
conflicts and the need to have these files in the first place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7bgc
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes from Arnd Bergmann:
"These are 18 branches on 9 platforms with board specific changes,
mostly for defconfig files, but nothing really exciting in here.
Since the shmobile platform still uses board files for some of the
newer machines, we get a few changes there as the result of drivers
getting enabled for those boards. This causes some conflicts with
contents getting added from multiple branches in sh-mobile specific
files. Renesas is putting a lot of work into migrating to device-tree
based setup, which will make all those files obsolete in the future
and avoid both the conflicts and the need to have these files in the
first place."
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
arm: multi_v7_defconfig: Enable initrd/initramfs support
arm: multi_v7_defconfig: Enable Zynq UART driver
ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
ARM: OMAP1: nokia770: enable Tahvo
ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
arm: omap: board-overo: reset GPIO for SMSC911x
ARM: shmobile: BOCK-W: change Ether device name
ARM: ux500: board-mop500: remove unused pin modes
ARM: shmobile: bockw: add MMCIF support
ARM: shmobile: bockw: add SPI FLASH support
ARM: shmobile: bockw: add I2C device support
ARM: shmobile: BOCK-W: add Ether support
ARM: tegra: defconfig updates
ARM: shmobile: bockw defconfig: add MMCIF support
ARM: shmobile: bockw defconfig: add M25P80 support
ARM: shmobile: bockw defconfig: add RTC RX8581 support
ARM: shmobile: marzen: keep local function as static
ARM: shmobile: bockw: add SDHI0 support
ARM: shmobile: marzen: Use INTC External IRQ pin driver for SMSC
ARM: shmobile: lager: support GPIO switches
...
These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in
this branch, both containing almost no platform specific code at all,
since they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part of
the SoC specific code. With the changes done by Thomas Petazzoni, we can
now more easily have PCI host controller drivers as loadable modules and
keep them separate from the platform code in drivers/pci/host. This has
already led to the discovery that three platforms (exynos, spear and imx)
are actually using an identical PCIe host controller and will be able
to share a driver once support for spear and imx is added.
Conflicts:
* asm/glue-proc.h has one CPU type getting added that conflicts
with another addition in 3.10-rc7
* Simple context changes in arch/arm/Makefile and arch/arm/Kconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0r9S
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
This contains cleanups as preparation for other branches adding new
features, we pulled 16 branches for 9 platforms into this one.
Most notable here is the removal of support for ATAGS based OMAP4
systems. Since all OMAP4 machines are fully functional with DT based
booting in 3.10, we can remove a lot of code here.
Also noteworthy is Maxime Ripard's cleanup of the machine descriptors,
which means we need no machine descriptors in a lot more cases and
can boot additional machines by just having the respective device
drivers enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XDJs
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"This contains cleanups as preparation for other branches adding new
features, we pulled 16 branches for 9 platforms into this one.
Most notable here is the removal of support for ATAGS based OMAP4
systems. Since all OMAP4 machines are fully functional with DT based
booting in 3.10, we can remove a lot of code here.
Also noteworthy is Maxime Ripard's cleanup of the machine descriptors,
which means we need no machine descriptors in a lot more cases and can
boot additional machines by just having the respective device drivers
enabled."
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
ARM: picoxcell: remove .nr_irqs reference
ARM: s5p64x0: avoid build warning for uncompress.h
ARM: SAMSUNG: Remove unused plat/regs-watchdog.h header
ARM: SAMSUNG: Remove legacy watchdog reset code
ARM: SAMSUNG: Let platforms use the new watchdog reset driver
ARM: SAMSUNG: Add watchdog reset driver
ARM: SAMSUNG: Use local definitions of watchdog registers
watchdog: s3c2410_wdt: Use local register definitions
ARM: S5P64X0: Use common uncompress.h part for plat-samsung
ARM: SAMSUNG: Consolidate uncompress subroutine
ARM: at91: drop rm9200dk board support
ARM: dts: msm: Fix merge resolution
ARM: OMAP1: Remove dma.h
ARM: OMAP1: Remove legacy irda.h and irda setup from board files
ARM: OMAP1: Remove duplicated DMA channel definitions
ARM: OMAP1: Remove McBSP DMA channel definitions
ARM: OMAP2+: Remove dma.h
ARM: OMAP2+: hwmod: Remove remaining DMA channel definitions
ARM: OMAP2+: Remove duplicated DMA channel definitions
ARM: OMAP2+: Remove AES crypto device DMA channel definitions
...
These are various bug fixes that were not considered important enough
for merging into 3.10. The majority of the ARM fixes are for the OMAP
and at91 platforms, and there is another set of bug fixes for device
drivers that resolve 'randconfig' build errors and that the subsystem
maintainers either did not pick up or preferred to get merged through
the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gNDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-cricitical bug fixes from Arnd Bergmann:
"These are various bug fixes that were not considered important enough
for merging into 3.10.
The majority of the ARM fixes are for the OMAP and at91 platforms, and
there is another set of bug fixes for device drivers that resolve
'randconfig' build errors and that the subsystem maintainers either
did not pick up or preferred to get merged through the arm-soc tree."
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91/PMC: use at91_usb_rate() for UTMI PLL
ARM: at91/PMC: fix at91sam9n12 USB FS init
ARM: at91/PMC: at91sam9n12 family has a PLLB
ARM: at91/PMC: sama5d3 family doesn't have a PLLB
ARM: tegra: fix section mismatch in tegra_pmc_parse_dt
ARM: mxs: don't select HAVE_PWM
ARM: mxs: stub out mxs_pm_init for !CONFIG_PM
cpuidle: calxeda: select ARM_CPU_SUSPEND
ARM: mvebu: fix length of ethernet registers in mv78260 dtsi
ARM: at91: cpuidle: Fix target_residency
ARM: at91: fix at91_extern_irq usage for non-dt boards
ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessary
clocksource: kona: adapt to CLOCKSOURCE_OF_DECLARE change
X.509: do not emit any informational output
mtd: omap2: allow bulding as a module
[SCSI] nsp32: use mdelay instead of large udelay constants
hwrng: bcm2835: fix MODULE_LICENSE tag
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
MAINTAINERS: Add exynos filename match to ARM/S5P EXYNOS ARM ARCHITECTURES
...
Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just removed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRsGMACgkQMUfUDdst+ylIIACfW8lLxOPVK+iYG699TWEBAkp0
LFEAnjlpAMJ1JnoZCuWDZObNCev93zGB
=020+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just
removed)"
* tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
driver core: device.h: fix doc compilation warnings
firmware loader: fix another compile warning with PM_SLEEP unset
build some drivers only when compile-testing
firmware loader: fix compile warning with PM_SLEEP set
kobject: sanitize argument for format string
sysfs_notify is only possible on file attributes
firmware loader: simplify holding module for request_firmware
firmware loader: don't export cache_firmware and uncache_firmware
drivers/base: Use attribute groups to create sysfs memory files
firmware loader: fix compile warning
firmware loader: fix build failure with !CONFIG_FW_LOADER_USER_HELPER
Documentation: Updated broken link in HOWTO
Finally eradicate CONFIG_HOTPLUG
driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests before suspend
driver core: firmware loader: don't cache FW_ACTION_NOHOTPLUG firmware
Documentation: Tidy up some drivers/base/core.c kerneldoc content.
platform_device: use a macro instead of platform_driver_register
firmware: move EXPORT_SYMBOL annotations
firmware: Avoid deadlock of usermodehelper lock at shutdown
dell_rbu: Select CONFIG_FW_LOADER_USER_HELPER explicitly
...
Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is a
nice change, just a number of serial driver fixes and updates and new
drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with the
exception of the last revert patch, which was reported this past weekend
by two different people as being needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRtNIACgkQMUfUDdst+ymYgwCeKdyv9wRJ5cIWZt7Jz8ou3P/C
76YAoIvMv+fwoFBpyud/sC8eAKGTQ6KB
=Sjk6
-----END PGP SIGNATURE-----
Merge tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big TTY / Serial driver merge for 3.11-rc1.
It's not all that big, nothing major changed in the tty api, which is
a nice change, just a number of serial driver fixes and updates and
new drivers, along with some n_tty fixes to help resolve some reported
issues.
All of these have been in the linux-next releases for a while, with
the exception of the last revert patch, which was reported this past
weekend by two different people as being needed."
* tag 'tty-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (51 commits)
Revert "serial: 8250_pci: add support for another kind of NetMos Technology PCI 9835 Multi-I/O Controller"
pch_uart: Add uart_clk selection for the MinnowBoard
tty: atmel_serial: prepare clk before calling enable
tty: Reset itty for other pty
n_tty: Buffer work should not reschedule itself
n_tty: Fix unsafe update of available buffer space
n_tty: Untangle read completion variables
n_tty: Encapsulate minimum_to_wake within N_TTY
serial: omap: Fix device tree based PM runtime
serial: imx: Fix serial clock unbalance
serial/mpc52xx_uart: fix kernel panic when system reboot
serial: mfd: Add sysrq support
serial: imx: enable the clocks for console
tty: serial: add Freescale lpuart driver support
serial: imx: Improve Kconfig text
serial: imx: Allow module build
serial: imx: Fix warning when !CONFIG_SERIAL_IMX_CONSOLE
tty/serial/sirf: fix error propagation in sirfsoc_uart_probe()
serial: omap: fix potential NULL pointer dereference in serial_omap_runtime_suspend()
tty: serial: Enable uartlite for ARM zynq
...
Here's the big USB 3.11-rc1 merge request.
Lots of gadget and finally, chipidea driver updates (they were much
needed), along with a new host controller driver, lots of little serial
driver fixes, the removal of the 255 usb-serial device limitation, and a
variety of other minor things.
All of these have been in the linux-next releases for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRtqkACgkQMUfUDdst+ykIWACguGzwSkoBjh2q8p+M6l4zGwQI
fSAAoJvh8OKLWS7J3VkTWkyYy+Z2XV5d
=FdaG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB 3.11-rc1 merge request.
Lots of gadget and finally, chipidea driver updates (they were much
needed), along with a new host controller driver, lots of little
serial driver fixes, the removal of the 255 usb-serial device
limitation, and a variety of other minor things.
All of these have been in the linux-next releases for a while"
* tag 'usb-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (254 commits)
usb: musb: omap2430: make it compile again
usb: chipidea: ci_hdrc_imx: access phy via private data
xhci: Add missing unlocks on error paths
USB: option,qcserial: move Novatel Gobi1K IDs to qcserial
ehci-atmel.c: prepare clk before calling enable
USB: ohci-at91: prepare clk before calling enable
USB: HWA: fix device probe failure
wusbcore: add entries in Documentation/ABI for new wusbhc sysfs attributes
wusbcore: add sysfs attribute for retry count
wusbcore: add sysfs attribute for DNTS count and interval
usb: chipidea: drop "13xxx" infix
usb: phy: tegra: remove duplicated include from phy-tegra-usb.c
usb: host: xhci-plat: release mem region while removing module
usbmisc_imx: allow autoloading on according to dt ids
usb: fix build error without CONFIG_USB_PHY
usb: check usb_hub_to_struct_hub() return value
xhci: check for failed dma pool allocation
usb: gadget: f_subset: fix missing unlock on error in geth_alloc()
usb: gadget: f_ncm: fix missing unlock on error in ncm_alloc()
usb: gadget: f_ecm: fix missing unlock on error in ecm_alloc()
...
Pull VFS patches (part 1) from Al Viro:
"The major change in this pile is ->readdir() replacement with
->iterate(), dealing with ->f_pos races in ->readdir() instances for
good.
There's a lot more, but I'd prefer to split the pull request into
several stages and this is the first obvious cutoff point."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (67 commits)
[readdir] constify ->actor
[readdir] ->readdir() is gone
[readdir] convert ecryptfs
[readdir] convert coda
[readdir] convert ocfs2
[readdir] convert fatfs
[readdir] convert xfs
[readdir] convert btrfs
[readdir] convert hostfs
[readdir] convert afs
[readdir] convert ncpfs
[readdir] convert hfsplus
[readdir] convert hfs
[readdir] convert befs
[readdir] convert cifs
[readdir] convert freevxfs
[readdir] convert fuse
[readdir] convert hpfs
reiserfs: switch reiserfs_readdir_dentry to inode
reiserfs: is_privroot_deh() needs only directory inode, actually
...
The vpe.c code uses the 'struct module' which is only available if
CONFIG_MODULES is selected.
Also fixes the following build problem on a lantiq allmodconfig:
In file included from arch/mips/kernel/vpe.c:41:0:
include/linux/moduleloader.h: In function 'apply_relocate':
include/linux/moduleloader.h:48:63: error: dereferencing pointer
to incomplete type
include/linux/moduleloader.h: In function 'apply_relocate_add':
include/linux/moduleloader.h:70:63: error: dereferencing pointer
to incomplete type
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5562/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several drivers use the clk_{set,round}_rate() functions
that need to be defined in the platform's clock code.
The Broadcom BCM63xx platform hardcodes the clock rate so
we create new clk_{set,round}_rate() functions
which just return 0 like those in include/linux/clk.h
for the common clock framework do.
Also fixes the following build problem on a randconfig:
drivers/built-in.o: In function `nop_usb_xceiv_probe':
phy-nop.c:(.text+0x3ec26c): undefined reference to `clk_set_rate'
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5580/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The route_irq() function needs to preserve the irq mask by using the
_irqsave/irqrestore variants of raw spin lock functions instead of the
_irq variants. This is because it is called from __cpu_disable() (via
migrate_irqs()), which is called with IRQs disabled, so using the _irq
variants re-enables IRQs.
This appears to have been causing occasional hits of the
BUG_ON(!irqs_disabled()) in __irq_work_run() during CPU hotplug soak
testing:
BUG: failure at kernel/irq_work.c:122/__irq_work_run()!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
kick_handler() doesn't have an irq_enter/exit pair, but it's used for
handling SMP IPIs which require work to be done in softirqs, which are
invoked from irq_exit() when the hard irq nest count reaches 0.
The scheduler_ipi() callback in the IPI handler calls irq_enter/exit
itself, but this is inside kick_handler()'s spin lock critical section,
so if an invoked softirq issues an IPI the kick_handler() will be
re-entered on the same CPU and will deadlock.
This is easily fixed by adding the missing irq_enter/exit to
kick_handler() so that the hard irq nest count doesn't reach 0 until
after the spin lock has been released.
Ideally the spin lock protected handler list will also be replaced by a
lockless RCU protected list since it is certainly mostly read. That can
be done in a later change though.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Use a completion to block until a secondary CPU has started up, like ARM
do, instead of a loop of udelays.
On Meta, SMP is really SMT, with each "CPU" being a different hardware
thread on the same Meta processor core, so as well as being more
efficient and latency friendly, using a completion prevents the bogomips
of the secondary CPU from being drastically skewed every time by the
execution of the tight in-cache udelay loop on the other CPU.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
In secondary_start_kernel() interrupts should be enabled with
local_irq_enable() after the cpu is marked as online with
set_cpu_online(). Otherwise it's possible for a timer interrupt to
trigger a softirq, which if the cpu is marked as offline may have it's
affinity altered.
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Kirill Tkhai <tkhai@yandex.ru>
Checking for process->mm is not enough because process' main thread may
exit or detach its mm via use_mm(), but other threads may still have a
valid mm.
To fix this we would need to use find_lock_task_mm(), which would walk
up all threads and returns an appropriate task (with task lock held).
clear_tasks_mm_cpumask() was introduced in v3.5-rc1 to fix this issue,
so let's use it for metag too.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
From Anatolij:
"There are small cleanups and fixes for mpc512x common code,
mpc512x_defconfig updates and soft reboot support for mpc5125
based boards."
Reschedule vector tracepoints may be called in cpu idle state.
This causes lockdep check warning below.
The tracepoint requires rcu but for accuracy it also
requires irq_enter() (tracepoints record the irq context), thus,
the tracepoint interrupt handler should be calling irq_enter()
and not rcu_irq_enter() (irq_enter() calls rcu_irq_enter()).
So, add irq_enter/exit() to smp_trace_reschedule_interrupt()
with common pre/post processing functions, smp_entering_irq()
and exiting_irq() (exiting_irq() calls just irq_exit()
in arch/x86/include/asm/apic.h),
because these can be shared among reschedule, call_function,
and call_function_single vectors.
[ 50.720557] Testing event reschedule_exit:
[ 50.721349]
[ 50.721502] ===============================
[ 50.721835] [ INFO: suspicious RCU usage. ]
[ 50.722169] 3.10.0-rc6-00004-gcf910e8 #190 Not tainted
[ 50.722582] -------------------------------
[ 50.722915] /c/kernel-tests/src/linux/arch/x86/include/asm/trace/irq_vectors.h:50 suspicious rcu_dereference_check() usage!
[ 50.723770]
[ 50.723770] other info that might help us debug this:
[ 50.723770]
[ 50.724385]
[ 50.724385] RCU used illegally from idle CPU!
[ 50.724385] rcu_scheduler_active = 1, debug_locks = 0
[ 50.725232] RCU used illegally from extended quiescent state!
[ 50.725690] no locks held by swapper/0/0.
[ 50.726010]
[ 50.726010] stack backtrace:
[...]
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/51CDCFA3.9080101@hds.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix GIO3 base addresses for EMEV2.
This bug was introduced by 088efd9273
("mach-shmobile: Emma Mobile EV2 GPIO support V3") which was included in v3.5.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Cc: stable@vger.kernel.org
The driver provides a way to wake up the system by the MPIC timer.
For example,
echo 5 > /sys/devices/system/mpic/timer_wakeup
echo standby > /sys/power/state
After 5 seconds the MPIC timer will generate an interrupt to wake up
the system.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Register a mpic subsystem at /sys/devices/system/
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The MPIC global timer is a hardware timer inside the Freescale PIC complying
with OpenPIC standard. When the specified interval times out, the hardware
timer generates an interrupt. The driver currently is only tested on fsl chip,
but it can potentially support other global timers complying to OpenPIC
standard.
The two independent groups of global timer on fsl chip, group A and group B,
are identical in their functionality, except that they appear at different
locations within the PIC register map. The hardware timer can be cascaded to
create timers larger than the default 31-bit global timers. Timer cascade
fields allow configuration of up to two 63-bit timers. But These two groups
of timers cannot be cascaded together.
It can be used as a wakeup source for low power modes. It also could be used
as periodical timer for protocols, drivers and etc.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add irq_set_wake support. Just add IRQF_NO_SUSPEND to desc->action->flag.
So the wake up interrupt will not be disable in suspend_device_irqs.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
With the patch 7230c564 (powerpc: Rework lazy-interrupt handling),
it seems that the coreint works pretty well on the 85xx 64bit kernel.
So use the coreint by default for these boards.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
irq_eoi() is already called by generic_handle_irq() so
it shall not be called a again
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the most boards of Freescale platform, they use the PCI-Express
Intel(R) PRO/1000 gigabit ethernet card to work. So enable the
corresponding driver for it.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
MPIC version is useful information for both mpic_alloc() and mpic_init().
The patch provide an API to get MPIC version for reusing the code.
Also, some other IP block may need MPIC version for their own use.
The API for external use is also provided.
Signed-off-by: Jia Hongtao <hongtao.jia@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When Jeremy introduced the new device-tree based reserve map, he made
the code in early_reserve_mem_dt() bail out if it found one, thus not
reserving the initrd nor processing the old style map.
I hit problems with variants of kexec that didn't put the initrd in
the new style map either. While these could/will be fixed, I believe
we should be safe here and rather reserve more than not enough.
We could have a firmware passing stuff via the new style map, and
in the middle, a kexec that knows nothing about it and adding other
things to the old style map.
I don't see a big issue with processing both and reserving everything
that needs to be. memblock_reserve() supports overlaps fine these days.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Data Address Watchpoint Register (DAWR) on POWER8 can take a 512
byte range but this range must not cross a 512 byte boundary.
Unfortunately we were off by one when calculating the end of the region,
hence we were not allowing some breakpoint regions which were actually
valid. This fixes this error.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: Edjunior Barbosa Machado <emachado@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The vref field was not used by the driver and was removed from the
platform data structure.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Whenever a DASD request encounters a timeout we might
need to abort all outstanding requests on this or
even other devices.
This is especially useful if one wants to fail all
devices on one side of a RAID10 configuration, even
though only one device exhibited an error.
To handle this I've introduced a new device flag
DASD_FLAG_ABORTIO.
This flag is evaluated in __dasd_process_request_queue()
and will invoke blk_abort_request() for all
outstanding requests with DASD_CQR_FLAGS_FAILFAST set.
This will cause any of these requests to be aborted
immediately if the blk_timeout function is activated.
The DASD_FLAG_ABORTIO is also evaluated in
__dasd_process_request_queue to abort all
new request which would have the
DASD_CQR_FLAGS_FAILFAST bit set.
The flag can be set with the new ioctls 'BIODASDABORTIO'
and removed with 'BIODASDALLOWIO'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a misleading naming of the program parameter fields, so
correct them according to their names as outlined in
"The Load-Program-Parameter and the CPU-measurement Facilities"
(SA23-2260-03).
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cores used on the SEAD-3 platform do not have L2 caches, so
this option should not be turned on. Originally fixed on public
'linux-mti-3.8' release branch.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5559/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BCM6328 has a OTP which tells us if the second core is available.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/5490/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This involves two changes to the BSP code:
1) register_smp_ops() for BMIPS SMP
2) The CPU1 boot vector on some of the BCM63xx platforms conflicts with
the special interrupt vector (IV). Move it to 0x8000_0380 at boot time,
to resolve the conflict.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
[jogo@openwrt.org: moved SMP ops registration into ifdef guard,
changed ifdef guards to if (IS_ENABLED())]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: John Crispin <blogic@openwrt.org>
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5489/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS does define read{b,w,l,q}_relaxed but does not define their write
counterparts: write{b,w,l,q}_relaxed. This patch adds the missing
definitions for the write*_relaxed I/O accessors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GENERIC_PCI_IOMAP does not depend on CONFIG_PCI so move
it to the CONFIG_MIPS symbol so it's always selected for MIPS.
This fixes the missing pci_iomap declaration for MIPS.
Moreover, the pci_iounmap function was not defined in the
io.h header file if the CONFIG_PCI symbol is not set,
but it should since MIPS is not using CONFIG_GENERIC_IOMAP.
This fixes the following problem on a allyesconfig:
drivers/net/ethernet/3com/3c59x.c:1031:2: error: implicit declaration of
function 'pci_iomap' [-Werror=implicit-function-declaration]
drivers/net/ethernet/3com/3c59x.c:1044:3: error: implicit declaration of
function 'pci_iounmap' [-Werror=implicit-function-declaration]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5478/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add GCMP detection for IASim Marvell chip emulation support.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/5529/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 3f4579252aa166641861a64f1c2883365ca126c2. It is
invalid because the macros CAC_ADDR and UNCAC_ADDR have a kernel
virtual address as an argument and also returns a kernel virtual
address. Using and physical address PHYS_OFFSET is blatantly wrong
for a macro common to multiple platforms.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5528/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ISA exception bit selects whether exceptions are taken in classic
or microMIPS mode. This bit is Config3.ISAOnExc and was improperly
defined as bits 16 and 17 instead of just bit 16. A new function was
added so that platforms could set this bit when running a kernel
compiled with only microMIPS instructions.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5377/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In mm_isBranchInstr() we can short circuit the entire function if
!cpu_has_mmips.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5326/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is only used from within a single file, it should not be globally
visible.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5325/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS43xx CPUs have two hardware threads, and on some SoCs such as 3368,
the bootloader has configured the system to boot from TP1 instead of the
more usual TP0. Create the physical to logical CPU mapping to cope with
that, do not remap the software interrupts to be cross CPUs such that we
do not have to do use the logical CPU mapping further down the code, and
finally, reset the slave TP1 only if booted from TP0.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: blogic@openwrt.org
Cc: cernekee@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/5553/
Patchwork: https://patchwork.linux-mips.org/patch/5556/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As Jonas Gorske said in his patch:
Disable cpu_has_mmips for everything but SEAD3 and MALTA. Most of
these platforms are from before the micromips introduction, so they
are very unlikely to implement it.
Reduces an -Os compiled, uncompressed kernel image by 8KiB for
BCM63XX.
This patch taks a different approach than his, we gate the runtime
test for microMIPS by the config symbol SYS_SUPPORTS_MICROMIPS.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5327/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is an infinite loop in gic_set_affinity. When irq_set_affinity
gets called on gic controller, it blocks forever.
Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5537/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ABI allows these to be clobbered on syscalls, so only save and
restore the multiplier state when the temporary registers need to be
preserved.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/5540/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable interfaces on EdgeRouter Lite. Tested with cavium_octeon_defconfig
and busybox shell. DHCP & ping works with eth0, eth1 and eth2.
The board type "UBNT_E100" is taken from the sources of the vendor kernel
shipped with the product.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5546/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Prepare of a next patch which will call tlbmiss_handler_setup_pgd on
microMIPS. MicroMIPS complains if the called code s not in the .text
section. To fix this we generate code into space reserved in
arch/mips/mm/tlb-funcs.S
While there, move the rest of the generated functions (handle_tlbl,
handle_tlbs, handle_tlbm) to the same file.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5542/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS I is the ancestor of all MIPS ISA and architecture variants. Anything
ever build in the MIPS empire is either MIPS I or at least contains MIPS I.
If it's running Linux, that is.
So there is little point in having cpu_has_mips_1 because it will always
evaluate as true - though usually only at runtime. Thus there is no
point in having the MIPS_CPU_ISA_I ISA flag, so get rid of it.
Little complication: traps.c was using a test for a pure MIPS I ISA as
a test for an R3000-style cp0. To deal with that, use a check for
cpu_has_3kex or cpu_has_4kex instead.
cpu_has_3kex is a new macro. At the moment its default implementation is
!cpu_has_4kex but this may eventually change if Linux is ever going to
support the oddball MIPS processors R6000 and R8000 so users of either
of these macros should not make any assumptions.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5551/
Following patch to use generic 8250 drivers will need proper clock
information. So when using the internal device tree, populate the
"clock-frequency" property with the correct value.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5515/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some boards may need to reset their external PHY or switch they are
attached to, add a hook for doing this along with providing custom
linux/gpio.h flags for doing this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Cc: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5501/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The BCM3368 SoC uses a NVRAM format which is not compatible with the one
used by CFE, provide a default MAC address which is suitable for use and
which is the default one also being used by the bootloader on these
chips.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5498/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the firmware header format which is used by Broadcom Cable Modem
SoCs such as the BCM3368 SoC. We export the bcm_hcs firmware format
structure because it is used by user-land tools to create firmware
images for these SoCs and will later be used by a corresponding MTD
parser.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5496/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Broadcom BCM3368 Cable Modem SoC is extremely similar to the
existing BCM63xx DSL SoCs, in particular BCM6358, therefore little effort
in the existing code base is required to get it supported. This patch adds
support for the following on-chip peripherals:
- two UARTS
- GPIO
- Ethernet
- SPI
- PCI
- NOR Flash
The most noticeable difference with 3368 is that it has its peripheral
register at 0xfff8_0000 we check that separately in ioremap.h. Since
3368 is identical to 6358 for its clock and reset bits, we use them
verbatim.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5499/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enabling BOOT_RAW is mandatory to get a binary image (objcopy from ELF
to binary) to work. This does not affect the ELF kernels which are used
by CFE on BCM63XX DSL platforms, but is going to be necessary to support
BCM63XX on Cable Modem chips such as BCM3368.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: cernekee@gmail.com
Cc: jogo@openwrt.org
Patchwork: https://patchwork.linux-mips.org/patch/5500/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This board has been EOL for many years now; lets not burden people doing
build coverage and other tree wide work with working on essentially dead
files.
[ralf@linux-mips.org: Also remove arch/mips/include/asm/mach-wrppmc/war.h.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Patchwork: http://patchwork.linux-mips.org/patch/5503/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
