Before this patch, when compiled for arm32, the signal strength
were reported as:
Lock (0x1f) Signal= 4294908.66dBm C/N= 12.79dB
Because of a 32 bit integer overflow. After it, it is properly
reported as:
Lock (0x1f) Signal= -58.64dBm C/N= 12.79dB
Cc: stable@vger.kernel.org
Fixes: 0f91c9d6ba ("[media] TS2020: Calculate tuner gain correctly")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cleanup the mess in init_search_param() by utilising the new register
access macros and functions. And while at it, move the ISI and PLS setup
into separate functions, and pass the new scrambling_sequence_index (aka.
physical layer scrambling) value to set_pls.
Picked up from the dddvb upstream, adapted to the different naming of the
pls property (pls vs. scrambling_sequence_index).
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a write_field() function that acts as helper to update specific bits
specified in the field defines (FSTV0910_*) in stv0910_regs.h, which was
recently updated to carry the missing offset values. With that, add the
SET_FIELD(), SET_REG() and GET_REG() macros that wrap the write_field(),
write_reg() and read_reg() functions to allow for making all demod
access code cleaner.
The write_field() function is annotated with __maybe_unused temporarily
to silence eventual compile warnings.
Picked up from the dddvb upstream, with the macro names made uppercase
so they are distinguishable as such.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
write_reg() and i2c_write_reg16() only act as a proxy to i2c_write(), which
isn't called from anywhere else throughout the driver. Clean this up by
moving the message setup and the i2c_transfer() into write_reg() so it
becomes the only I2C write function. While touching those parts, fix the
error codes from EREMOTEIO to EIO.
The I2C cleanup is picked from the upstream dddvb.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For all code rates, the same write is performed, only with a differing
value. Clean this up by putting that value into a variable instead and
perform the write at the end with that value.
Picked up from the dddvb upstream.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes 2 warnings from Clang about extra parentheses in a conditional,
that might have been meant as assignment.
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This commit uses the new property scrambling_sequence_index
to control PLS.
By default we are using the gold sequence 0 and only gold sequences
expected on the new property.
Please note that all services use PLS, just most with the default
sequence 0 and many demods only support gold 0.
Signed-off-by: Athanasios Oikonomou <athoik@gmail.com>
Acked-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A typical code fragment was copied across many dvb-frontend drivers and
causes large stack frames when built with with CONFIG_KASAN on gcc-5/6/7:
drivers/media/dvb-frontends/cxd2841er.c:3225:1: error: the frame size of 3992 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/cxd2841er.c:3404:1: error: the frame size of 3136 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/stv0367.c:3143:1: error: the frame size of 4016 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/stv090x.c:3430:1: error: the frame size of 5312 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
drivers/media/dvb-frontends/stv090x.c:4248:1: error: the frame size of 4872 bytes is larger than 3072 bytes [-Werror=frame-larger-than=]
gcc-8 now solves this by consolidating the stack slots for the argument
variables, but on older compilers we can get the same behavior by taking
the pointer of a local variable rather than the inline function argument.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On faster CPUs a delay is required after the resume command and the restart command. Without the delay, the restart command often returns -EREMOTEIO and the Si2168 does not restart.
Note that this patch fixes the same issue as https://patchwork.linuxtv.org/patch/44304/, but I believe my udelay() fix addresses the actual problem.
Signed-off-by: Ron Economos <w6rz@comcast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since nothing from dvb_math.h is used, remove the unneeded include.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
tracking_optimization() doesn't make use of the symbol rate reported by
the demodulator, so remove the unneeded inquiry and the now unneeded
variable.
Reported-by: Richard Scobie <rascobie@slingshot.co.nz>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Utilise get_cur_symbol_rate() in get_frontend() to update the
dtv_frontend_properties with the current symbol rate as reported by the
demodulator.
Reported-by: Richard Scobie <rascobie@slingshot.co.nz>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The result (if any) isn't used anywhere besides being assigned to a local
variable (and the only current companion stv6111 doesn't even implement
get_if_frequency()), thus remove the ptr check and the call, and also
remove the now unused iffreq variable.
Reported-by: Richard Scobie <rascobie@slingshot.co.nz>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When a parent (demod) driver encounters and signals a problem with
gate_ctrl(), don't blindly continue poking the I2C bus.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stack dump when gate_ctrl() is called in a way that consecutive unlocks
happen. This is a clear indication that other drivers interfacing with
the stv0910 driver don't do things properly or don't check for failures,
so dump stack so that those drivers can be identified and fixed.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Each field (FSTV0910_XX) is declared as reg/off/unused/sign/mask. Add
the missing offset value to the defines.
Picked up from dddvb master, commit 8a1f27c3d22c ("add field offset to
field defines") by Ralph Metzler <rjkm@metzlerbros.de>, adapted to
match the comment style in the mainline driver.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The assignment status to itself is redundant and can be removed.
Detected with Coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The self assignment of temporary is redundant and can be removed.
Detected using coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The self assignment of k_indirect is redundant and can be removed.
Detected using coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add read_ber function that reads from property cache to support DVBv3.
The implementation is inspired by the cx24120 driver.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add read_snr function that reads from property cache to support DVBv3.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for BER statistics.
Configure a measurement period of 30000 packets.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use check_signal register for DVB-T additionally.
For DVB-C use ps_lock additionally.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use constellation from property cache instead of always setting it to
QAM256.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The lock timeout should not depend on the bandwidth.
It should be either constant or depend on xtal frequency.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The TS parallel mode setting should be where all other TS settings are written.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert register numbers to macros.
Correctness verified by comparing the disassembly before and after.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix almost all of checkpatch --strict warnings.
The remaining warnings are about:
* macro REG16 (should be enclosed in parentheses)
* macro REG16 (Macro argument reuse)
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Removed module parameter debug and the conditions based on it.
Now it can be configured via dynamic debug.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/dvb-frontends/drxd_hard.c:989 HI_Command() error: uninitialized symbol 'waitCmd'.
drivers/media/dvb-frontends/drxd_hard.c:1306 SC_WaitForReady() error: uninitialized symbol 'curCmd'.
drivers/media/dvb-frontends/drxd_hard.c:1322 SC_SendCommand() error: uninitialized symbol 'errCode'.
drivers/media/dvb-frontends/drxd_hard.c:1339 SC_ProcStartCommand() error: uninitialized symbol 'scExec'.
The error handling on several places are somewhat flawed, as
they don't check if Read16() returns an error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The loop with read status use a dynamic timeout value, calculated
from symbol rate. It should run the loop at least one time for
the status to be handled after the loop.
While this should, in practice, happen every time, it doesn't
hurt to change the logic to make it explicit.
This solves a smatch warning:
drivers/media/dvb-frontends/cxd2841er.c:3350 cxd2841er_set_frontend_s() error: uninitialized symbol 'status'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the tuner doesn't have get_frequency() callback, the current
code will place a random value as the frequency offset. That
doesn't seem right! The better is to just assume that, on such
case, the tuner was able to set the exact frequency that was
requested.
Fixes a smatch warning:
drivers/media/dvb-frontends/m88rs2000.c:639 m88rs2000_set_frontend() error: uninitialized symbol 'tuner_freq'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/dvb-frontends/mb86a16.c:1690 mb86a16_read_ber() error: uninitialized symbol 'timer'.
drivers/media/dvb-frontends/mb86a16.c:1706 mb86a16_read_ber() error: uninitialized symbol 'timer'.
There is a potential risk of doing a division by zero if
timer is not handled well. Enforce it by setting a bit mask
for the values used to select the timer.
It should be noticed that I don't have mb86a16 datasheet. So,
the bitmask was guessed based on the existing checks for
the field. At worse case scenario, it will just show a
badly calculated bit error rate, but it won't crash.
While here, optimize the logic to prevent uneeded tests.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the I2C read fails while check for sync, there's no point
on doing adjusting the tuner due to a random value that might
be at VIRM var. So, set VIRM to zero, as that makes the caller
for check_sync() to return an error.
Fix those smatch warnings:
drivers/media/dvb-frontends/mb86a16.c:1460 mb86a16_set_fe() error: uninitialized symbol 'VIRM'.
drivers/media/dvb-frontends/mb86a16.c:1461 mb86a16_set_fe() error: uninitialized symbol 'VIRM'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
as reported by smatch:
drivers/media/dvb-frontends/drx39xyj/drxj.c:2157 drxj_dap_atomic_read_write_block() error: uninitialized symbol 'word'.
The driver doesn't check if a read error occurred. Add such
check.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current code doesn't report tuner lock properly if the
tuner get_status callback is not available, as reported by
smatch:
drivers/media/dvb-frontends/stv090x.c:2220 stv090x_get_coldlock() error: uninitialized symbol 'reg'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add missing state->modcod update from upstream driver which needs to be
done when manage_matype_info() sets is_vcm on certain S2 transponders.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The tuning logic is broken with regards to status report:
it relies on a previously-cached value that may not be valid
if re-tuned.
Change the logic to always read the status.
Acked-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For the dvb-frontends that are now part of the documentation,
complete the kernel-doc markups, in order for them to be
properly used at the driver's kAPI documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now, the Kernel checks for kernel_doc format issues.
Weird enough, it didn't get any of those troubles. Shssst!
Well, let's fix it, as a preventive way to avoid having
hundreds of new warnings on some next Linux version.
Tested by adding all files under dvb-frontends that have
"/**" on them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned:
drivers/media/dvb-frontends/ix2505v.c:24: warning: cannot understand function prototype: 'int ix2505v_debug; '
drivers/media/dvb-frontends/ix2505v.c:59: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/ix2505v.c:128: warning: No description found for parameter 'fe'
None of the comments there are kernel-doc. So, remove them with:
perl -pi -e 's,\/\*\*,/*,g' drivers/media/dvb-frontends/ix2505v.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those drivers use a different notation for comments. While
it is not worth converting to kernel-doc, removing it is also
not an option.
So, just replace /** by /* and be happy :-)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
