The tricky part here is that task_pt_regs() on m68k works *only* for
process inside do_signal(). However, we need something much simpler -
pt_regs of a process inside do_signal() may be at different offsets
from the stack bottom, depending on the way we'd entered the kernel,
but for a task inside sys_execve() it *is* at constant offset.
Moreover, for a kernel thread about to become a userland process the
same location is also fine - setting sp to that will leave the kernel
stack pointer at the very bottom of the kernel stack when we finally
switch to userland.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The stack frame "format" field needs to be explicitly set on thread creation
on ColdFire. For a normal long word aligned user stack pointer the frame
format is 0x4.
We were doing this for non-MMU ColdFire, but not for the case with MMU enabled.
So fix it so we always do it if targeting ColdFire.
The old code happend to rely on the stack frame format being inhereted from
the process calling exec. Furture changes means that may not always work,
so we really do want to set it explicitly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
the only non-obvious part is that current_pt_regs() is really needed
here - task_pt_regs() is NULL for kernel threads; it's OK for ptrace
uses (the thing task_pt_regs() is intended for), but not for us.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
32bit wrapper is lost on that; 64bit one is *not*, since
we need to arrange for full pt_regs on stack when we call
sys_execve() and we need to load callee-saved ones from
there afterwards.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... no need to read current_thread_info()->task only to
feed it to task_thread_page() immediately afterwards.
Moreover, not using current_thread_info() at all ends
up with better assembler - we need a location very close
to the top of kernel stack page and it's actually better
to do or with 0x1fff, followed be subtracting a small
constant than and with ~0x1fff, followed by adding a large
one. Both & and | would be a couple of insns (mvn lsr/mvn lsl
for |, a pair of bic for &), but the following addition
would cost a pair of add while the subtraction ends up
as a single sub.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Let architectures select GENERIC_KERNEL_THREAD and have their copy_thread()
treat NULL regs as "it came from kernel_thread(), sp argument contains
the function new thread will be calling and stack_size - the argument for
that function". Switching the architectures begins shortly...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
we only use that to tell copy_thread() done by syscall from that
done by kernel_thread(). However, it's easier to do simply by
checking PF_KTHREAD in thread flags.
Merge sys_clone() guts for 32bit and 64bit, while we are at it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
TIF_NOTIFY_RESUME will work in precisely the same way; all that
is achieved by TIF_IRET is appearing that there's some work to be
done, so we end up on the iret exit path. Just use NOTIFY_RESUME.
And for execve() do that in 32bit start_thread(), not sys_execve()
itself.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBYK+cACgkQGkmNcg7/o7jthwCfemhnr590s3hwWXjA88ZZMFDl
U8kAoJA7hNCtAqdoj+LHXJlKLK1UalkD
=aCxD
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix up TIF_NOTIFY_RESUME sans TIF_SIGPENDING handling.
sh: pfc: Release spinlock in sh_pfc_gpio_request_enable() error path
sh: intc: Fix up multi-evt irq association.
As Al notes, we missed a TIF_NOTIFY_RESUME check which caused any
handlers without TIF_SIGPENDING also set to skip the notification:
Looks like while it is in the relevant masks *and* checked in
do_notify_resume() both on 32bit and 64bit variants since commit
ab99c733ae ("sh: Make syscall tracer
use tracehook notifiers, add TIF_NOTIFY_RESUME.") they are
actually *not* reached without simulataneous SIGPENDING, since
the actual glue in the callers had not been updated back then and
still checks for _TIF_SIGPENDING alone when deciding whether to
hit do_notify_resume() or not.
Reported-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull one more DMA-mapping fix from Marek Szyprowski:
"This patch fixes very subtle bug (typical off-by-one error) which
might appear in very rare circumstances."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: mm: fix DMA pool affiliation check
Pull perf fixes from Ingo Molnar:
"This tree includes various fixes"
Ingo really needs to improve on the whole "explain git pull" part.
"Various fixes" indeed.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/hwpb: Invoke __perf_event_disable() if interrupts are already disabled
perf/x86: Enable Intel Cedarview Atom suppport
perf_event: Switch to internal refcount, fix race with close()
oprofile, s390: Fix uninitialized memory access when writing to oprofilefs
perf/x86: Fix microcode revision check for SNB-PEBS
- A set of OMAP fixes, about half of them PM/clock related, the rest
scattered over the platform code but all small and targeted to real bugs.
- Two small i.MX fixes for SSI device clock setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=y6Db
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Olof Johansson:
- A set of OMAP fixes, about half of them PM/clock related, the rest
scattered over the platform code but all small and targeted to real
bugs.
- Two small i.MX fixes for SSI device clock setup.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: clk-imx35: Fix SSI clock registration
ARM: clk-imx25: Fix SSI clock registration
ARM: OMAP4: Fix array size for irq_target_cpu
ARM: OMAP4: hwmod data: temporarily comment out data for the sl2if IP block
ARM: OMAP: hwmod code: Disable module when hwmod enable fails
ARM: OMAP3: hwmod data: fix iva2 reset info
ARM: OMAP3xxx: clockdomain: fix software supervised wakeup/sleep
ARM: OMAP2+: am33xx: Fix the timer fck clock naming convention
ARM: OMAP: Config fix for omap3-touchbook board
ARM: OMAP: sram: skip the first 16K on OMAP3 HS
ARM: OMAP: sram: fix OMAP4 errata handling
ARM: OMAP: timer: obey the !CONFIG_OMAP_32K_TIMER
Pull ARM fixes from Russell King:
"It's been a while... so there's a little more here than normal.
Mostly updates from Will for the breakpoint stuff, and plugging a few
holes in the user access functions which crept in when domain support
was disabled for ARMv7 CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7529/1: delay: set loops_per_jiffy when moving to timer-based loop
ARM: 7528/1: uaccess: annotate [__]{get,put}_user functions with might_fault()
ARM: 7527/1: uaccess: explicitly check __user pointer when !CPU_USE_DOMAINS
ARM: 7526/1: traps: send SIGILL if get_user fails on undef handling path
ARM: 7521/1: Fix semihosting Kconfig text
ARM: 7513/1: Make sure dtc is built before running it
ARM: 7512/1: Fix XIP build due to PHYS_OFFSET definition moving
ARM: 7499/1: mm: Fix vmalloc overlap check for !HIGHMEM
ARM: 7503/1: mm: only flush both pmd entries for classic MMU
ARM: 7502/1: contextidr: avoid using bfi instruction during notifier
ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores
ARM: 7497/1: hw_breakpoint: allow single-byte watchpoints on all addresses
ARM: 7496/1: hw_breakpoint: don't rely on dfsr to show watchpoint access type
ARM: Fix ioremap() of address zero
Pull blackfin updates from Bob Liu:
"One kbuild and a smp build fix."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
kbuild: add symbol prefix arg to kallsyms
blackfin: smp: adapt to generic smp helpers
SSI block has two types of clock:
ipg: bus clock, the clock needed for accessing registers.
per: peripheral clock, the clock needed for generating the bit rate.
Currently SSI driver only supports slave mode and only need to handle
the ipg clock, because the peripheral clock comes from the master codec.
Only register the ipg clock and do not register the peripheral clock for ssi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
SSI block has two types of clock:
ipg: bus clock, the clock needed for accessing registers.
per: peripheral clock, the clock needed for generating the bit rate.
Currently SSI driver only supports slave mode and only need to handle
the ipg clock, because the peripheral clock comes from the master codec.
Only register the ipg clock and do not register the peripheral clock for ssi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org
Commit 1f2bfbd00e ("kbuild: link of
vmlinux moved to a script") introduced in v3.5-rc1 broke kallsyms on
architectures which have symbol prefixes.
The --symbol-prefix argument used to be added to the KALLSYMS command
line from the architecture Makefile, however this isn't picked up by the
new scripts/link-vmlinux.sh. This resulted in symbols like
kallsyms_addresses being added which weren't correctly overriding the
weak symbols such as _kallsyms_addresses. These could then trigger
BUG_ONs in kallsyms code.
This is fixed by removing the KALLSYMS addition from the architecture
Makefile, and using CONFIG_SYMBOL_PREFIX in the link-vmlinux.sh script
to determine whether to add the --symbol-prefix argument.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BPP1
-----END PGP SIGNATURE-----
Merge tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Avi Kivity:
"A trio of KVM fixes: incorrect lookup of guest cpuid, an uninitialized
variable fix, and error path cleanup fix."
* tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: fix error paths for failed gfn_to_page() calls
KVM: x86: Check INVPCID feature bit in EBX of leaf 7
KVM: PIC: fix use of uninitialised variable.
The __free_from_pool() function was changed in
e9da6e9905. Unfortunately, the test that
checks whether the provided (start,size) is within the DMA pool has
been improperly modified. It used to be:
if (start < coherent_head.vm_start || end > coherent_head.vm_end)
Where coherent_head.vm_end was non-inclusive (i.e, it did not include
the first byte after the pool). The test has been changed to:
if (start < pool->vaddr || start > pool->vaddr + pool->size)
So now pool->vaddr + pool->size is inclusive (i.e, it includes the
first byte after the pool), so the test should be >= instead of >.
This bug causes the following message when freeing the *first* DMA
coherent buffer that has been allocated, because its virtual address
is exactly equal to pool->vaddr + pool->size :
WARNING: at /home/thomas/projets/linux-2.6/arch/arm/mm/dma-mapping.c:463 __free_from_pool+0xa4/0xc0()
freeing wrong coherent size from pool
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Maen Suleiman <maen@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Shadi Ammouri <shadi@marvell.com>
Cc: Eran Ben-Avi <benavi@marvell.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
[m.szyprowski: rebased onto v3.6-rc5 and resolved conflict]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
