Seville does not need to depend on PCI or on the ENETC MDIO controller.
There will also be other compile-time differences in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is another switch from Vitesse / Microsemi / Microchip, that has
10 ports (8 external, 2 internal) and is integrated into the Freescale /
NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A,
except that this is a platform device and Felix is a PCI device, and it
doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus
using a phy_device abstraction for it (yes, it will be refactored to use
a raw mdio_device, like other phylink drivers do, but let's keep it like
that for now). But unlike Felix, the MDIO bus and the PCS are not from
the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in
Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it
is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it
would be difficult to reuse that driver (it doesn't even use regmap, and
it's less than 200 lines of code), so we hand-roll here some internal
MDIO bus accessors within seville_vsc9953.c, which serves the purpose of
driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of
SerDes protocol, so we need to do pre-validation of PHY mode from device
tree and not let phylink change it.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This supports an Ethernet switching core from Vitesse / Microsemi /
Microchip (VSC9959) which is part of the Ocelot family (a brand name),
and whose code name is Felix. The switch can be (and is) integrated on
different SoCs as a PCIe endpoint device.
The functionality is provided by the core of the Ocelot switch driver
(drivers/net/ethernet/mscc). In this regard, the current driver is an
instance of Microsemi's Ocelot core driver, with a DSA front-end. It
inherits its name from VSC9959's code name, to distinguish itself from
the switchdev ocelot driver.
The patch adds the logic for probing a PCI device and defines the
register map for the VSC9959 switch core, since it has some differences
in register addresses and bitfield mappings compared to the other Ocelot
switches (VSC7511, VSC7512, VSC7513, VSC7514).
The Felix driver declares the register map as part of the "instance
table". Currently the VSC9959 inside NXP LS1028A is the only instance,
but presumably it can support other switches in the Ocelot family, when
used in DSA mode (Linux running on the external CPU, and not on the
embedded MIPS).
In a few cases, some h/w operations have to be done differently on
VSC9959 due to missing bitfields. This is the case for the switch core
reset and init. Because for this operation Ocelot uses some bits that
are not present on Felix, the latter has to use a register from the
global registers block (GCB) instead.
Although it is a PCI driver, it relies on DT bindings for compatibility
with DSA (CPU port link, PHY library). It does not have any custom
device tree bindings, since we would like to minimize its dependency on
device tree though.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
