The driver periodically checks for adapter error in a background thread. If
the thread detects an error, the adapter will be reset including the
deletion and reallocation of workqueues on the adapter. Simultaneously,
there may be a user-space request to offline the adapter which may try to
do many of the same steps, in parallel, on a different thread. As memory
was deallocated while unexpected, the parallel offline request hit a bad
pointer.
Add coordination between the two threads. The error recovery thread has
precedence. So, when an error is detected, a flag is set on the adapter to
indicate the error thread is terminating the adapter. But, before doing
that work, it will look for a flag that is set by the offline flow, and if
set, will wait for it to complete before then processing the error handling
path. Similarly, in the offline thread, it first checks for whether the
error thread is resetting the adapter, and if so, will then wait for the
error thread to finish. Only after it has finished, will it set its flag
and offline the adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a couple of cases, the driver detected a pci error (via pci device state
or via failed register reads) but didn't take any action to disable the
device. Additionally, the driver is ignoring the status of pci
configuration space reads.
Having the driver take the adapter offline whenever the pci error is
detected. Pay attention to pci_config_space_read status and return failure
if an error is seen.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an adapter fails, causing a board reset, the board reset routine
lpfc_hba_down_s4() takes the hbalock out then calls
lpfc_nvmet_ctxbuf_post() who then tries to take out the same lock. As the
context lists are now protected under the buf_list_locks, there is no need
for the hbalock to be held by the board reset routine.
Fix by no longer taking the hbalock in the board reset routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With negative test injection, the driver is receiving a command with first
burst enabled, meaning Sequence initiative is not passed with the command
frame. The driver notes the condition and discards the frame. However the
driver calls the incorrect buffer free routine, resulting in a NULL pointer
reference.
For hbq buffer free, convert to using lpfc_rq_buf_free().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, when lpfc_nvmet_mrq is 0 it could mean 2 different things
depending on when its looked at. If at module load time it specifies the
default number of hardware queues to allocate, with 0 meaning default to
the number of CPUs. But post module load, a value of zero means to disable
mrq use.
Changed the driver so that enablement of mrq is based on whether nvme
target mode is enabled or not. When enabled, mrq is enabled. Thus, the
cfg_nvemt_mrq field only specifies the number of mrq queues to enable, with
0 defaulting to the number of cpus.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under circustances with high load, the driver is running out of async
receive buffers which may result in one of the following messages:
0:6401 RQE Error x13, posted 226 err_cnt 0: 925c6050 925c604e 925c5d54
or
0:2885 Port Status Event: port status reg 0x81800000,
port smphr reg 0xc000, error 1=0x52004a01, error 2=0x0
The driver is waiting for full io completion before returning receive
buffers to the adapter. There is no need for such a relationship.
Whenever a new command is received from the wire, the driver will have two
contexts - an io context (ctxp) and a receive buffer context. In current
code, the receive buffer context stays 1:1 with the io and won't be
reposted to the hardware until the io completes. There is no need for such
a relationship.
Change the driver so that up on successful handing of the command to the
transport, where the transport has copied what it needed thus the buffer is
returned to the driver, have the driver immediately repost the buffer to
the hardware. If the command cannot be successfully handed to the transport
as transport resources are temporarily busy, have the driver allocate a new
and separate receive buffer and post it to the hardware so that hardware
can continue while the command is queued for the transport.
When an io is complete, the transport returns the io context to the driver,
and the driver may be waiting for more contexts, thus immediately reuse the
io context. In this path, there was a buffer posted when the receive buffer
was queued waiting for an io context so a replacement is not needed in the
new code additions. Thus, exempt this the context reuse case from the
buffer reposting.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The debug ktime counters that trace an io were inadvertently not placed in
the common section of an io buffer. Thus, they generate an invalid opcode
error when accessed.
Move the ktime counters into the common area.
Fixes: 0794d601d1 ("scsi: lpfc: Implement common IO buffers between NVME and SCSI")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A patch in the 12.2.0.0 set caused a new lockdep warning:
WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
5.0.0-rc8-next-20190301-dbg+ #1 Not tainted
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&qp->io_buf_list_put_lock)->rlock);
local_irq_disable();
lock(&(&phba->hbalock)->rlock);
lock(&(&qp->io_buf_list_put_lock)->rlock);
<Interrupt>
lock(&(&phba->hbalock)->rlock);
see: https://www.spinics.net/lists/linux-scsi/msg128389.html
In summary, the new patch added taking the io_buf_list_put_lock while under
an irq-disabled hbalock. This created a lock heirarchy dependent upon irq
being disabled, and there are paths that take the io_buf_list_put_lock
without disabling irq.
Looking at the lpfc_io_free routine, which is where the new heirarchy was
introduced, there is no reason to be taking out the hbalock and raising
irq, as the functionality is replaced by the io_buf_list_xxx locks.
Resolve by removing the hbalock/irq calls in lpfc_io_free.
Fixes: 5e5b511d8b ("scsi: lpfc: Partition XRI buffer list across Hardware Queues")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A prior patch which added support for non-uniform allocation of MSIX
vectors now causes a smatch complaint:
drivers/scsi/lpfc/lpfc_scsi.c:3674 lpfc_scsi_cmd_iocb_cmpl()
error: we previously assumed 'phba->sli4_hba.hdwq' could be
null (see line 3667)
Resolve by removing the unnecessary check for a NULL hdwq table.
Fixes 6a828b0f61: ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This version includes support for ISP28XX.
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for Secure flash update with ISP28xx.
Signed-off-by: Michael Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Includes the following:
- correction to 27xx image status struct;
- factoring of 27xx image status validating routines to make common;
- image status generation compare that works across zero wrap;
- bsg interface to report current active images (as loaded by driver).
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reduce stack space on each fwdt routine by eliminating local variable reg.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch cleans up and fixes firmware dump template processing. These
changes are added to support newer features for ISP27XX/ISP28XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes following changes to flash access routines:
- update return type for read_optrom
- use void instead of uint32_t * for buffer parameter in read
and write optrom routines
- fix flash/nvram addressing
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds multipe firmware dump template and segments support for
ISP27XX/28XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does following:
- Clean up NVRAM code.
- Optimizes reading of primary/secondary flash image validation.
- Remove 0xff mask and make correct width in FLT structure.
- Use endian macros to assign static fields in fwdump header.
- Correct fdwt checksum calculation.
- Simplify ql_dump_buffer() interface usage.
- Add endianizers to 27xx firmware image validator.
- fixes compiler warnings for big endian architecture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes reported speed for min_link and max_supported speed. Also
rename sysfs nodes link_speed and max_supported to be consistent with
{min|max}_suuported_speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Mike Hernandez <mhernandez@marvell.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds sysfs node for serdes_version and also cleans up port_speed
display.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds PCI device ID ISP28XX for Gen7 support. Also signature
determination for primary/secondary flash image for ISP27XX/28XX is aded as
part of Gen7 support.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes qla27xx_dump_{mpi|ram} api for ISP27XX.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch removes FW default template as there will never be case where
the default template would be invoked.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds new sysfs node to display firmware attributes and port
number.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version to 28.100.00.00, which is equivalent to OOB Phase 9.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Reduce the threshold value to 1/4 of the queue depth.
* With this FW can find enough entries to post the Reply Descriptors in the
reply descriptor post queue.
* With module param, user can play with threshold value, the same
irqpoll_weight is used as the budget in processing of reply descriptor
post queues in _base_process_reply_queue.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver uses "reply descriptor post queues" in round robin fashion so that
IO's are distributed to all the available reply descriptor post queues
equally. With this each reply descriptor post queue load is balanced.
This is enabled only if CPUs count to MSI-X vector count ratio is X:1
(where X > 1) This improves performance and also fixes soft lockups.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue Description:
We have seen cpu lock up issue from fields if system has greater (more than
96) logical cpu count. SAS3.0 controller (Invader series) supports at max
96 msix vector and SAS3.5 product (Ventura) supports at max 128 msix
vectors.
This may be a generic issue (if PCI device supports completion on multiple
reply queues). Let me explain it w.r.t to mpt3sas supported h/w just to
simplify the problem and possible changes to handle such issues. IT HBA
(mpt3sas) supports multiple reply queues in completion path. Driver creates
MSI-x vectors for controller as "min of (FW supported Reply queue, Logical
CPUs)". If submitter is not interrupted via completion on same CPU, there
is a loop in the IO path. This behavior can cause hard/soft CPU lockups, IO
timeout, system sluggish etc.
Example - one CPU (e.g. CPU A) is busy submitting the IOs and another CPU
(e.g. CPU B) is busy with processing the corresponding IO's reply
descriptors from reply descriptor queue upon receiving the interrupts from
HBA. If the CPU A is continuously pumping the IOs then always CPU B (which
is executing the ISR) will see the valid reply descriptors in the reply
descriptor queue and it will be continuously processing those reply
descriptor in a loop without quitting the ISR handler.
Mpt3sas driver will exit ISR handler if it finds unused reply descriptor in
the reply descriptor queue. Since CPU A will be continuously sending the
IOs, CPU B may always see a valid reply descriptor (posted by HBA Firmware
after processing the IO) in the reply descriptor queue. In worst case,
driver will not quit from this loop in the ISR handler. Eventually, CPU
lockup will be detected by watchdog.
Above mentioned behavior is not common if "rq_affinity" set to 2 or
affinity_hint is honored by irqbalance as "exact". If rq_affinity is set
to 2, submitter will be always interrupted via completion on same CPU. If
irqbalance is using "exact" policy, interrupt will be delivered to
submitter CPU.
If CPU counts to MSI-X vectors (reply descriptor Queues) count ratio is not
1:1, we still have exposure of issue explained above and for that we don't
have any solution.
Exposure of soft/hard lockup if CPU count is more than MSI-x supported by
device.
If CPUs count to MSI-x vectors count ratio is not 1:1, (Other way, if CPU
counts to MSI-x vector count ratio is something like X:1, where X > 1) then
'exact' irqbalance policy OR rq_affinity = 2 won't help to avoid CPU
hard/soft lockups. There won't be any one to one mapping between CPU to
MSI-x vector instead one MSI-x interrupt (or reply descriptor queue) is
shared with group/set of CPUs and there is a possibility of having a loop
in the IO path within that CPU group and may observe lockups.
For example: Consider a system having two NUMA nodes and each node having
four logical CPUs and also consider that number of MSI-x vectors enabled on
the HBA is two, then CPUs count to MSI-x vector count ratio as 4:1. e.g.
MSIx vector 0 is affinity to CPU 0, CPU 1, CPU 2 & CPU 3 of NUMA node 0 and
MSI-x vector 1 is affinity to CPU 4, CPU 5, CPU 6 & CPU 7 of NUMA node 1.
numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 --> MSI-x 0
node 0 size: 65536 MB
node 0 free: 63176 MB
node 1 cpus: 4 5 6 7 -->MSI-x 1
node 1 size: 65536 MB
node 1 free: 63176 MB
Assume that user started an application which uses all the CPUs of NUMA
node 0 for issuing the IOs. Only one CPU from affinity list (it can be any
cpu since this behavior depends upon irqbalance) CPU0 will receive the
interrupts from MSIx vector 0 for all the IOs. Eventually, CPU 0 IO
submission percentage will be decreasing and ISR processing percentage will
be increasing as it is more busy with processing the interrupts. Gradually
IO submission percentage on CPU 0 will be zero and it's ISR processing
percentage will be 100 percentage as IO loop has already formed within the
NUMA node 0, i.e. CPU 1, CPU 2 & CPU 3 will be continuously busy with
submitting the heavy IOs and only CPU 0 is busy in the ISR path as it
always find the valid reply descriptor in the reply descriptor
queue. Eventually, we will observe the hard lockup here.
Chances of occurring of hard/soft lockups are directly proportional to
value of X. If value of X is high, then chances of observing CPU lockups is
high.
Solution: Use IRQ poll interface defined in " irq_poll.c". mpt3sas driver
will execute ISR routine in Softirq context and it will always quit the
loop based on budget provided in IRQ poll interface.
In these scenarios (i.e. where CPUs count to MSI-X vectors count ratio is
X:1 (where X > 1)), IRQ poll interface will avoid CPU hard lockups due to
voluntary exit from the reply queue processing based on budget. Note -
Only one MSI-x vector is busy doing processing.
Irqstat output:
IRQs / 1 second(s)
IRQ# TOTAL NODE0 NODE1 NODE2 NODE3 NAME
44 122871 122871 0 0 0 IR-PCI-MSI-edge mpt3sas0-msix0
45 0 0 0 0 0 IR-PCI-MSI-edge mpt3sas0-msix1
We use this approach only if cpu count is more than FW supported MSI-x
vector
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Separate out processing of reply descriptor post queue from _base_interrupt
to _base_process_reply_queue.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed typo in request_desript_type.
request_desript_type --> request_descript_type.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Ajish Koshy <ajish.koshy@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are times when a TUR can take longer than the DEFAULT_TIMEOUT
value. The timeout code is not correct as the function exits with an
automatic as the completion variable...To be fixed later.
Remove the TUR timeout.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a 'rare' race condition where a disk is failed after a device list
has been obtained from the controller and before attempting to get the
device id.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Multipath failures are normally detected at the frequency of the event
thread. Detect LUN failures earlier by checking request completion status.
Reviewed-by: Bader Ali-saleh <bader.ali-saleh@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Prasad Munirathnam <Prasad.Munirathnam@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
Fix performance issue where the queue depth for SmartIOC logical volumes is
set to 1, and allow the usual logical volume code to be executed
Fixes: a052865fe2 (aacraid: Set correct Queue Depth for HBA1000 RAW disks)
Cc: stable@vger.kernel.org
Signed-off-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It used to be that "error" was set to -ENODEV at the start of the function
but we shifted some code around an now "error" is set to zero for most
error paths. There is a mix of direct returns and "goto out" but I changed
everything to direct returns for consistency.
Fixes: 56de835704 ("scsi: lpfc: fix calls to dma_set_mask_and_coherent()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
If there is an error queueing an iscsi command in iscsi_queuecommand(), for
example if the transport fails to take the command in
sessuin->tt->xmit_task(), then the error path can call
iscsi_complete_task() without first aquiring the back_lock as
required. This can lead to things like ITT pool can get corrupt, resulting
in duplicate ITTs being sent out.
The solution is to hold the back_lock around iscsi_complete_task() calls,
and to add a little commenting to help others understand when back_lock
must be held.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With default value of register SERDES_CFG, the link is not stable for some
special disks when running IO. According to HW guys' suggestion, need to
make the bit10~19 value of register SERDES_CFG the max value to increase
the reliability of the HiLink.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Yupeng Zhou <zhouyupeng1@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we exchange SAS expander from one SAS controller to other SAS controller
without powering it down, the STP target port will maintain previous
affiliation and reject all subsequent connection requests from other STP
initiator ports with OPEN_REJECT (STP RESOURCES BUSY).
To solve this issue, send HARD RESET to clear the previous affiliation of
STP target port according to SPL (chapter 6.19.4).
We (re-)introduce dev status flag to know if to sleep in NEXUS reset code
or not for remote PHYs. The idea is that if the device is being
initialised, we don't require the delay, and caller would wait for link to
be established, cf. sas_ata_hard_reset().
Co-developed-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the PHY comes down, we currently do not set the negotiated linkrate:
root@(none)$ pwd
/sys/class/sas_phy/phy-0:0
root@(none)$ more enable
1
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
12.0 Gbit
root@(none)$
This patch fixes the driver code to set it properly when the PHY comes
down.
If the PHY had been enabled, then set unknown; otherwise, flag as disabled.
The logical place to set the negotiated linkrate for this scenario is PHY
down routine, which is called from the PHY down ISR.
However, it is not possible to know if the PHY comes down due to PHY
disable or loss of link, as sas_phy.enabled member is not set until after
the transport disable routine is complete, which races with the PHY down
ISR.
As an imperfect solution, use sas_phy_data.enable as the flag to know if
the PHY is down due to disable. It's imperfect, as sas_phy_data is internal
to libsas.
I can't see another way without adding a new field to hisi_sas_phy and
managing it, or changing SCSI SAS transport.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The later revision of v3 hw has added an function of interrupt coalesce
according to time for PHY RX errors. We set the coalesce time to 1s. Then
we print PHY RX errors count when PHY RX errors happen, and don't need to
worry that there may be too much log prints.
Besides, we use hisi_sas_phy.lock to protect error count value. Because we
update them by calling phy_get_events_v3_hw(), which is also used by core
driver (for get PHY events function).
We relocate phy_get_events_v3_hw() to avoid a further declaration.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
