Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add routines for Nemo specific devices to init at boot time, these
being board level power-off and SB600's rtc.
Also add a run time variable to prevent these being activated
if we boot on a reference board.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a IRQ init routine for the Nemo board which inits and attatches
the i8259 found in the SB600, and a cascade routine to dispatch the
interrupts.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The A-Eon Amigaone X1000's Nemo motherboard has an AMD SB600
connected to one of the PCI-e root ports on its PaSemi
Pwrficient 1628M SoC. Normally the SB600 southbridge would be
connected to a hidden PCI-e port on the system's northbridge,
and as a result doesn't fully comply with the PCI-e spec.
Add code to relax the PCI-e detection in both the root port
and the Linux kernel allowing on board devices to be detected.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As several other arches including x86, this patch makes it explicit
that a bad page fault is a NULL pointer dereference when the fault
address is lower than PAGE_SIZE
In the mean time, this page makes all bad_page_fault() messages
shorter so that they remain on one single line. And it prefixes them
by "BUG: " so that they get easily grepped.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Avoid pr_cont()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Combine the SYSCALL_EMU and SYSCALL_TRACE handling so that we only
call tracehook_report_syscall_entry() in one place.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
[mpe: Flesh out change log, s/cached_flags/flags/, reflow comments]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Powerpc has somewhat odd usage where ZONE_DMA is used for all memory on
common 64-bit configfs, and ZONE_DMA32 is used for 31-bit schemes.
Move to a scheme closer to what other architectures use (and I dare to
say the intent of the system):
- ZONE_DMA: optionally for memory < 31-bit (64-bit embedded only)
- ZONE_NORMAL: everything addressable by the kernel
- ZONE_HIGHMEM: memory > 32-bit for 32-bit kernels
Also provide information on how ZONE_DMA is used by defining
ARCH_ZONE_DMA_BITS.
Contains various fixes from Benjamin Herrenschmidt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The implemementation for the CONFIG_NOT_COHERENT_CACHE case doesn't share
any code with the one for systems with coherent caches. Split it off
and merge it with the helpers in dma-noncoherent.c that have no other
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The unmap methods need to transfer memory ownership back from the
device to the cpu by identical means as dma_sync_*_to_cpu. I'm not
sure powerpc needs to do any work in this transfer direction, but
given that it does invalidate the caches in dma_sync_*_to_cpu already
we should make sure we also do so on unmapping.
Signed-off-by: Christoph Hellwig <hch@lst.de>
[mpe: s/dir/direction in dma_nommu_unmap_page()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
AMIGAONE selects NOT_COHERENT_CACHE, so we better allow it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes early DEBUG messages in prom.c:
- Use %px instead of %p to see the addresses
- Cast memblock_phys_mem_size() with (unsigned long long) to
avoid build failure when phys_addr_t is not 64 bits.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When building for ppc32 with clang these flags are unsupported:
-ffixed-r2 and -mmultiple
llvm's lib/Target/PowerPC/PPCRegisterInfo.cpp marks r2 as reserved on
when building for SVR4ABI and !ppc64:
// The SVR4 ABI reserves r2 and r13
if (Subtarget.isSVR4ABI()) {
// We only reserve r2 if we need to use the TOC pointer. If we have no
// explicit uses of the TOC pointer (meaning we're a leaf function with
// no constant-pool loads, etc.) and we have no potential uses inside an
// inline asm block, then we can treat r2 has an ordinary callee-saved
// register.
const PPCFunctionInfo *FuncInfo = MF.getInfo<PPCFunctionInfo>();
if (!TM.isPPC64() || FuncInfo->usesTOCBasePtr() || MF.hasInlineAsm())
markSuperRegs(Reserved, PPC::R2); // System-reserved register
markSuperRegs(Reserved, PPC::R13); // Small Data Area pointer register
}
This means we can safely omit -ffixed-r2 when building for 32-bit
targets.
The -mmultiple/-mno-multiple flags are not supported by clang, so
platforms that might support multiple miss out on using multiple word
instructions.
We wrap these flags in cc-option so that when Clang gains support the
kernel will be able use these flags.
Clang 8 can then build a ppc44x_defconfig which boots in Qemu:
make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ppc44x_defconfig
./scripts/config -e CONFIG_DEVTMPFS -d DEVTMPFS_MOUNT
make CC=clang-8 ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu-
qemu-system-ppc -M bamboo \
-kernel arch/powerpc/boot/zImage \
-dtb arch/powerpc/boot/dts/bamboo.dtb \
-initrd ~/ppc32-440-rootfs.cpio \
-nographic -serial stdio -monitor pty -append "console=ttyS0"
Link: https://github.com/ClangBuiltLinux/linux/issues/261
Link: https://bugs.llvm.org/show_bug.cgi?id=39556
Link: https://bugs.llvm.org/show_bug.cgi?id=39555
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove PM_L2_ST_MISS and PM_L2_ST from HW cache event array since
these are bus events. And these needs to be programmed in groups.
Hence remove them.
Fixes: f1fb60bfde ('powerpc/perf: Export Power9 generic and cache events to sysfs')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In previous generation processors, both bus events and direct
events of performance monitoring unit can be individually
programmabled and monitored in PMCs.
But in Power9, L2/L3 bus events are always available as a
"bank" of 4 events. To obtain the counts for any of the
l2/l3 bus events in a given bank, the user will have to
program PMC4 with corresponding l2/l3 bus event for that
bank.
Patch enforce two contraints incase of L2/L3 bus events.
1)Any L2/L3 event when programmed is also expected to program corresponding
PMC4 event from that group.
2)PMC4 event should always been programmed first due to group constraint
logic limitation
For ex. consider these L3 bus events
PM_L3_PF_ON_CHIP_MEM (0x460A0),
PM_L3_PF_MISS_L3 (0x160A0),
PM_L3_CO_MEM (0x260A0),
PM_L3_PF_ON_CHIP_CACHE (0x360A0),
1) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r160A0,r260A0,r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r160A0,r260A0,r360A0}" < >
2) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r260A0,r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r260A0,r360A0}" < >
3) This is an INVALID group for L3 Bus event monitoring,
since it is missing PMC4 event.
perf stat -e "{r360A0}" < >
And this is a VALID group for L3 Bus events:
perf stat -e "{r460A0,r360A0}" < >
Patch here implements group constraint logic suggested by Michael Ellerman.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Raw event code has couple of fields "unit" and "cache" in it, to capture
the "unit" to monitor for a given pmcxsel and cache reload qualifier to
program in MMCR1.
isa207_get_constraint() refers "unit" field to update the MMCRC (L2/L3)
Event bus control fields with "cache" bits of the raw event code.
These are power8 specific and not supported by PowerISA v3.0 pmu. So wrap
the checks to be power8 specific. Also, "cache" bit field is referred to
update MMCR1[16:17] and this check can be power8 specific.
Fixes: 7ffd948fae ('powerpc/perf: factor out power8 pmu functions')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update the raw event code comment in power9-pmu.c with respect to
"cache" bits, since power9 MMCRC does not support these.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On each sample, Sample Instruction Event Register (SIER) content
is saved in pt_regs. SIER does not have a entry as-is in the pt_regs
but instead, SIER content is saved in the "dar" register of pt_regs.
Patch adds another entry to the perf_regs structure to include the "SIER"
printing which internally maps to the "dar" of pt_regs.
It also check for the SIER availability in the platform and present
value accordingly
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MMCRA[34:36] and MMCRA[38:44] expose the thresholding counter value.
Thresholding counter can be used to count latency cycles such as
load miss to reload. But threshold counter value is not relevant
when the sampled instruction type is unknown or reserved. Patch to
fix the thresholding counter value to zero when sampled instruction
type is unknown or reserved.
Fixes: 170a315f41c6('powerpc/perf: Support to export MMCRA[TEC*] field to userspace')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 2865d08dd9 ("powerpc/mm: Move the DSISR_PROTFAULT sanity
check") we moved the protection fault access check before the vma
lookup. That means we hit that WARN_ON when user space accesses a
kernel address. Before that commit this was handled by find_vma() not
finding vma for the kernel address and considering that access as bad
area access.
Avoid the confusing WARN_ON and convert that to a ratelimited printk.
With the patch we now get:
for load:
a.out[5997]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000)
a.out[5997]: segfault (11) at c00000000000dea0 nip 1317c0798 lr 7fff80d6441c code 1 in a.out[1317c0000+10000]
a.out[5997]: code: 60000000 60420000 3c4c0002 38427790 4bffff20 3c4c0002 38427784 fbe1fff8
a.out[5997]: code: f821ffc1 7c3f0b78 60000000 e9228030 <89290000> 993f002f 60000000 383f0040
for exec:
a.out[6067]: User access of kernel address (c00000000000dea0) - exploit attempt? (uid: 1000)
a.out[6067]: segfault (11) at c00000000000dea0 nip c00000000000dea0 lr 129d507b0 code 1
a.out[6067]: Bad NIP, not dumping instructions.
Fixes: 2865d08dd9 ("powerpc/mm: Move the DSISR_PROTFAULT sanity check")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Tested-by: Breno Leitao <leitao@debian.org>
[mpe: Don't split printk() string across lines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 603 doesn't have a HASH table, TLB misses are handled by
software. It is then possible to generate page fault when
_PAGE_EXEC is not set like in nohash/32.
There is one "reserved" PTE bit available, this patch uses
it for _PAGE_EXEC.
In order to support it, set_pte_filter() and
set_access_flags_filter() are made common, and the handling
is made dependent on MMU_FTR_HPTE_TABLE
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define slice_init_new_context_exec() at all time to avoid
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the following piece of code, the following compilation warning
is encountered:
if (_IOC_DIR(ioc) != _IOC_NONE) {
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
if (!access_ok(verify, ioarg, _IOC_SIZE(ioc))) {
drivers/platform/test/dev.c: In function 'my_ioctl':
drivers/platform/test/dev.c:219:7: warning: unused variable 'verify' [-Wunused-variable]
int verify = _IOC_DIR(ioc) & _IOC_READ ? VERIFY_WRITE : VERIFY_READ;
This patch fixes it by referencing 'type' in the macro allthough
doing nothing with it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit f21f49ea63 ("[POWERPC] Remove the dregs of APUS support from
arch/powerpc") removed CONFIG_APUS, but forgot to remove the logic
which adapts tophys() and tovirt() for it.
This patch removes the last stale pieces.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes the loop in p_block_mapped() and v_block_mapped()
to scan the entire bat_addrs[] array.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Depending on the CONFIG selected, many of the MMU features are
not possible. Lets only get the possible ones in MMU_FTRS_POSSIBLE.
This allows gcc to get rid at compile time of code related to
not possible features.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch sites and associated helpers to manage TLB handlers
patching instead of hardcoding.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of hardcoding the TLB handlers patching, use
the newly created modify_instruction_site() helper.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_sites and the new modify_instruction_site() function
instead of hardcoding hash functions patching.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of manually patching a blr at hash_page() entry in
MMU_init_hw(), this patch adds a features section in head_32.S
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use patch_site_addr() instead of hardcoding the
address calculation in machine_init()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add two helpers to avoid hardcoding of instructions modifications.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using patch_site_addr() helper, patch_instruction_site() and
patch_branch_site() can be simplified and inlined.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In file included from ./include/linux/hugetlb.h:445:0,
from arch/powerpc/kernel/setup-common.c:37:
./arch/powerpc/include/asm/hugetlb.h: In function ‘huge_ptep_clear_flush’:
./arch/powerpc/include/asm/hugetlb.h:154:8: error: variable ‘pte’ set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code:
ifdef CONFIG_6xx
KBUILD_CFLAGS += -mcpu=powerpc
endif
was added in 2006 in commit f48b8296b3 ("[PATCH] powerpc32: Set cpu
explicitly in kernel compiles"). This change was acceptable since the
TARGET_CPU logic was 64-bit only.
Since commit 0e00a8c9fd ("powerpc: Allow CPU selection
also on PPC32") this logic is no longer acceptable after the TARGET_CPU
specific. It currently appends -mcpu=powerpc at the end of the command
line, after any TARGET_CPU specific:
gcc -Wp,-MD,init/.do_mounts.o.d ...
-mcpu=powerpc -mbig-endian -m32 ...
-mcpu=e300c2 ...
-mcpu=powerpc ...
../init/do_mounts.c
Fixes: 0e00a8c9fd ("powerpc: Allow CPU selection also on PPC32")
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ipic_set_priority() has been unused since 2006 when the last usage was
removed in commit b9f0f1bb2b ("[POWERPC] Adapt ipic driver to new
host_ops interface, add set_irq_type to set IRQ sense").
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch again, this has a couple of build fixes and also
a change to do_syscall_trace_enter() that will conflict with a patch we
want to apply in next.
Use the new function to replace the open-coded iommu check.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell Currey <ruscur@russell.cc>
Cc: Sam Bobroff <sbobroff@linux.ibm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Previously when a device was being emulated by an L1 guest for an L2
guest, that device couldn't then be passed through to an L3 guest. This
was because the L1 guest had no method for accessing L3 memory.
The hcall H_COPY_TOFROM_GUEST provides this access. Thus this setup for
passthrough can now be allowed.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
A guest cannot access quadrants 1 or 2 as this would result in an
exception. Thus introduce the hcall H_COPY_TOFROM_GUEST to be used by a
guest when it wants to perform an access to quadrants 1 or 2, for
example when it wants to access memory for one of its nested guests.
Also provide an implementation for the kvm-hv module.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Allow for a device which is being emulated at L0 (the host) for an L1
guest to be passed through to a nested (L2) guest.
The existing kvmppc_hv_emulate_mmio function can be used here. The main
challenge is that for a load the result must be stored into the L2 gpr,
not an L1 gpr as would normally be the case after going out to qemu to
complete the operation. This presents a challenge as at this point the
L2 gpr state has been written back into L1 memory.
To work around this we store the address in L1 memory of the L2 gpr
where the result of the load is to be stored and use the new io_gpr
value KVM_MMIO_REG_NESTED_GPR to indicate that this is a nested load for
which completion must be done when returning back into the kernel. Then
in kvmppc_complete_mmio_load() the resultant value is written into L1
memory at the location of the indicated L2 gpr.
Note that we don't currently let an L1 guest emulate a device for an L2
guest which is then passed through to an L3 guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The functions kvmppc_st and kvmppc_ld are used to access guest memory
from the host using a guest effective address. They do so by translating
through the process table to obtain a guest real address and then using
kvm_read_guest or kvm_write_guest to make the access with the guest real
address.
This method of access however only works for L1 guests and will give the
incorrect results for a nested guest.
We can however use the store_to_eaddr and load_from_eaddr kvmppc_ops to
perform the access for a nested guesti (and a L1 guest). So attempt this
method first and fall back to the old method if this fails and we aren't
running a nested guest.
At this stage there is no fall back method to perform the access for a
nested guest and this is left as a future improvement. For now we will
return to the nested guest and rely on the fact that a translation
should be faulted in before retrying the access.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The kvmppc_ops struct is used to store function pointers to kvm
implementation specific functions.
Introduce two new functions load_from_eaddr and store_to_eaddr to be
used to load from and store to a guest effective address respectively.
Also implement these for the kvm-hv module. If we are using the radix
mmu then we can call the functions to access quadrant 1 and 2.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The POWER9 radix mmu has the concept of quadrants. The quadrant number
is the two high bits of the effective address and determines the fully
qualified address to be used for the translation. The fully qualified
address consists of the effective lpid, the effective pid and the
effective address. This gives then 4 possible quadrants 0, 1, 2, and 3.
When accessing these quadrants the fully qualified address is obtained
as follows:
Quadrant | Hypervisor | Guest
--------------------------------------------------------------------------
| EA[0:1] = 0b00 | EA[0:1] = 0b00
0 | effLPID = 0 | effLPID = LPIDR
| effPID = PIDR | effPID = PIDR
--------------------------------------------------------------------------
| EA[0:1] = 0b01 |
1 | effLPID = LPIDR | Invalid Access
| effPID = PIDR |
--------------------------------------------------------------------------
| EA[0:1] = 0b10 |
2 | effLPID = LPIDR | Invalid Access
| effPID = 0 |
--------------------------------------------------------------------------
| EA[0:1] = 0b11 | EA[0:1] = 0b11
3 | effLPID = 0 | effLPID = LPIDR
| effPID = 0 | effPID = 0
--------------------------------------------------------------------------
In the Guest;
Quadrant 3 is normally used to address the operating system since this
uses effPID=0 and effLPID=LPIDR, meaning the PID register doesn't need to
be switched.
Quadrant 0 is normally used to address user space since the effLPID and
effPID are taken from the corresponding registers.
In the Host;
Quadrant 0 and 3 are used as above, however the effLPID is always 0 to
address the host.
Quadrants 1 and 2 can be used by the host to address guest memory using
a guest effective address. Since the effLPID comes from the LPID register,
the host loads the LPID of the guest it would like to access (and the
PID of the process) and can perform accesses to a guest effective
address.
This means quadrant 1 can be used to address the guest user space and
quadrant 2 can be used to address the guest operating system from the
hypervisor, using a guest effective address.
Access to the quadrants can cause a Hypervisor Data Storage Interrupt
(HDSI) due to being unable to perform partition scoped translation.
Previously this could only be generated from a guest and so the code
path expects us to take the KVM trampoline in the interrupt handler.
This is no longer the case so we modify the handler to call
bad_page_fault() to check if we were expecting this fault so we can
handle it gracefully and just return with an error code. In the hash mmu
case we still raise an unknown exception since quadrants aren't defined
for the hash mmu.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
There exists a function kvm_is_radix() which is used to determine if a
kvm instance is using the radix mmu. However this only applies to the
first level (L1) guest. Add a function kvmhv_vcpu_is_radix() which can
be used to determine if the current execution context of the vcpu is
radix, accounting for if the vcpu is running a nested guest.
Currently all nested guests must be radix but this may change in the
future.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The kvm capability KVM_CAP_SPAPR_TCE_VFIO is used to indicate the
availability of in kernel tce acceleration for vfio. However it is
currently the case that this is only available on a powernv machine,
not for a pseries machine.
Thus make this capability dependent on having the cpu feature
CPU_FTR_HVMODE.
[paulus@ozlabs.org - fixed compilation for Book E.]
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to flush the partition-scoped page tables for a radix
guest when dirty tracking is turned on or off for a memslot. Only the
guest real addresses covered by the memslot are flushed. The reason
for this is to get rid of any 2M PTEs in the partition-scoped page
tables that correspond to host transparent huge pages, so that page
dirtiness is tracked at a system page (4k or 64k) granularity rather
than a 2M granularity. The page tables are also flushed when turning
dirty tracking off so that the memslot's address space can be
repopulated with THPs if possible.
To do this, we add a new function kvmppc_radix_flush_memslot(). Since
this does what's needed for kvmppc_core_flush_memslot_hv() on a radix
guest, we now make kvmppc_core_flush_memslot_hv() call the new
kvmppc_radix_flush_memslot() rather than calling kvm_unmap_radix()
for each page in the memslot. This has the effect of fixing a bug in
that kvmppc_core_flush_memslot_hv() was previously calling
kvm_unmap_radix() without holding the kvm->mmu_lock spinlock, which
is required to be held.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds 'const' to the declarations for the struct kvm_memory_slot
pointer parameters of some functions, which will make it possible to
call those functions from kvmppc_core_commit_memory_region_hv()
in the next patch.
This also fixes some comments about locking.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
For radix guests, this makes KVM map guest memory as individual pages
when dirty page logging is enabled for the memslot corresponding to the
guest real address. Having a separate partition-scoped PTE for each
system page mapped to the guest means that we have a separate dirty
bit for each page, thus making the reported dirty bitmap more accurate.
Without this, if part of guest memory is backed by transparent huge
pages, the dirty status is reported at a 2MB granularity rather than
a 64kB (or 4kB) granularity for that part, causing userspace to have
to transmit more data when migrating the guest.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, kvm_arch_commit_memory_region() gets called with a
parameter indicating what type of change is being made to the memslot,
but it doesn't pass it down to the platform-specific memslot commit
functions. This adds the `change' parameter to the lower-level
functions so that they can use it in future.
[paulus@ozlabs.org - fix book E also.]
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
One notable fix for our change to split pt_regs between user/kernel, we forgot
to update BPF to use the user-visible type which was an ABI break for BPF
programs.
A slightly ugly but minimal fix to do_syscall_trace_enter() so that we use
tracehook_report_syscall_entry() properly. We'll rework the code in next to
avoid the empty if body.
Seven commits fixing bugs in the new papr_scm (Storage Class Memory) driver.
The driver was finally able to be tested on the other hypervisor which exposed
several bugs. The fixes are all fairly minimal at least.
Fix a crash in our MSI code if an MSI-capable device is plugged into a non-MSI
capable PHB, only seen on older hardware (MPC8378).
Fix our legacy serial code to look for "stdout-path" since the device trees were
updated to use that instead of "linux,stdout-path".
A change to the COFF zImage code to fix booting old powermacs.
A couple of minor build fixes.
Thanks to:
Benjamin Herrenschmidt, Daniel Axtens, Dmitry V. Levin, Elvira Khabirova,
Oliver O'Halloran, Paul Mackerras, Radu Rendec, Rob Herring, Sandipan Das.
-----BEGIN PGP SIGNATURE-----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=wI/G
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One notable fix for our change to split pt_regs between user/kernel,
we forgot to update BPF to use the user-visible type which was an ABI
break for BPF programs.
A slightly ugly but minimal fix to do_syscall_trace_enter() so that we
use tracehook_report_syscall_entry() properly. We'll rework the code
in next to avoid the empty if body.
Seven commits fixing bugs in the new papr_scm (Storage Class Memory)
driver. The driver was finally able to be tested on the other
hypervisor which exposed several bugs. The fixes are all fairly
minimal at least.
Fix a crash in our MSI code if an MSI-capable device is plugged into a
non-MSI capable PHB, only seen on older hardware (MPC8378).
Fix our legacy serial code to look for "stdout-path" since the device
trees were updated to use that instead of "linux,stdout-path".
A change to the COFF zImage code to fix booting old powermacs.
A couple of minor build fixes.
Thanks to: Benjamin Herrenschmidt, Daniel Axtens, Dmitry V. Levin,
Elvira Khabirova, Oliver O'Halloran, Paul Mackerras, Radu Rendec, Rob
Herring, Sandipan Das"
* tag 'powerpc-4.20-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ptrace: replace ptrace_report_syscall() with a tracehook call
powerpc/mm: Fallback to RAM if the altmap is unusable
powerpc/papr_scm: Use ibm,unit-guid as the iset cookie
powerpc/papr_scm: Fix DIMM device registration race
powerpc/papr_scm: Remove endian conversions
powerpc/papr_scm: Update DT properties
powerpc/papr_scm: Fix resource end address
powerpc/papr_scm: Use depend instead of select
powerpc/bpf: Fix broken uapi for BPF_PROG_TYPE_PERF_EVENT
powerpc/boot: Fix build failures with -j 1
powerpc: Look for "stdout-path" when setting up legacy consoles
powerpc/msi: Fix NULL pointer access in teardown code
powerpc/mm: Fix linux page tables build with some configs
powerpc: Fix COFF zImage booting on old powermacs
When booting a kvm-pr guest on a POWER9 machine the following message is
observed:
"qemu-system-ppc64: KVM does not support 1TiB segments which guest expects"
This is because the guest is expecting to be able to use 1T segments
however we don't indicate support for it. This is because we don't set
the BOOK3S_HFLAG_MULTI_PGSIZE flag in the hflags in kvmppc_set_pvr_pr()
on POWER9.
POWER9 does indeed have support for 1T segments, so add a case for
POWER9 to the switch statement to ensure it is set.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Testing has revealed an occasional crash which appears to be caused
by a race between kvmppc_switch_mmu_to_hpt and kvm_unmap_hva_range_hv.
The symptom is a NULL pointer dereference in __find_linux_pte() called
from kvm_unmap_radix() with kvm->arch.pgtable == NULL.
Looking at kvmppc_switch_mmu_to_hpt(), it does indeed clear
kvm->arch.pgtable (via kvmppc_free_radix()) before setting
kvm->arch.radix to NULL, and there is nothing to prevent
kvm_unmap_hva_range_hv() or the other MMU callback functions from
being called concurrently with kvmppc_switch_mmu_to_hpt() or
kvmppc_switch_mmu_to_radix().
This patch therefore adds calls to spin_lock/unlock on the kvm->mmu_lock
around the assignments to kvm->arch.radix, and makes sure that the
partition-scoped radix tree or HPT is only freed after changing
kvm->arch.radix.
This also takes the kvm->mmu_lock in kvmppc_rmap_reset() to make sure
that the clearing of each rmap array (one per memslot) doesn't happen
concurrently with use of the array in the kvm_unmap_hva_range_hv()
or the other MMU callbacks.
Fixes: 18c3640cef ("KVM: PPC: Book3S HV: Add infrastructure for running HPT guests on radix host")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
While the dma-direct code is (relatively) clean and simple we actually
have to use the swiotlb ops for the mapping on many architectures due
to devices with addressing limits. Instead of keeping two
implementations around this commit allows the dma-direct
implementation to call the swiotlb bounce buffering functions and
thus share the guts of the mapping implementation. This also
simplified the dma-mapping setup on a few architectures where we
don't have to differenciate which implementation to use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
There is no need to have all setup and coherent allocation / freeing
routines inline. Move them out of line to keep the implemeation
nicely encapsulated and save some kernel text size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-11
The following pull-request contains BPF updates for your *net-next* tree.
It has three minor merge conflicts, resolutions:
1) tools/testing/selftests/bpf/test_verifier.c
Take first chunk with alignment_prevented_execution.
2) net/core/filter.c
[...]
case bpf_ctx_range_ptr(struct __sk_buff, flow_keys):
case bpf_ctx_range(struct __sk_buff, wire_len):
return false;
[...]
3) include/uapi/linux/bpf.h
Take the second chunk for the two cases each.
The main changes are:
1) Add support for BPF line info via BTF and extend libbpf as well
as bpftool's program dump to annotate output with BPF C code to
facilitate debugging and introspection, from Martin.
2) Add support for BPF_ALU | BPF_ARSH | BPF_{K,X} in interpreter
and all JIT backends, from Jiong.
3) Improve BPF test coverage on archs with no efficient unaligned
access by adding an "any alignment" flag to the BPF program load
to forcefully disable verifier alignment checks, from David.
4) Add a new bpf_prog_test_run_xattr() API to libbpf which allows for
proper use of BPF_PROG_TEST_RUN with data_out, from Lorenz.
5) Extend tc BPF programs to use a new __sk_buff field called wire_len
for more accurate accounting of packets going to wire, from Petar.
6) Improve bpftool to allow dumping the trace pipe from it and add
several improvements in bash completion and map/prog dump,
from Quentin.
7) Optimize arm64 BPF JIT to always emit movn/movk/movk sequence for
kernel addresses and add a dedicated BPF JIT backend allocator,
from Ard.
8) Add a BPF helper function for IR remotes to report mouse movements,
from Sean.
9) Various cleanups in BPF prog dump e.g. to make UAPI bpf_prog_info
member naming consistent with existing conventions, from Yonghong
and Song.
10) Misc cleanups and improvements in allowing to pass interface name
via cmdline for xdp1 BPF example, from Matteo.
11) Fix a potential segfault in BPF sample loader's kprobes handling,
from Daniel T.
12) Fix SPDX license in libbpf's README.rst, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Arch code should use tracehook_*() helpers, as documented in
include/linux/tracehook.h, ptrace_report_syscall() is not expected to
be used outside that file.
The patch does not look very nice, but at least it is correct
and opens the way for PTRACE_GET_SYSCALL_INFO API.
Co-authored-by: Dmitry V. Levin <ldv@altlinux.org>
Fixes: 5521eb4bca ("powerpc/ptrace: Add support for PTRACE_SYSEMU")
Signed-off-by: Elvira Khabirova <lineprinter@altlinux.org>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
[mpe: Take this as a minimal fix for 4.20, we'll rework it later]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull networking fixes from David Miller:
"A decent batch of fixes here. I'd say about half are for problems that
have existed for a while, and half are for new regressions added in
the 4.20 merge window.
1) Fix 10G SFP phy module detection in mvpp2, from Baruch Siach.
2) Revert bogus emac driver change, from Benjamin Herrenschmidt.
3) Handle BPF exported data structure with pointers when building
32-bit userland, from Daniel Borkmann.
4) Memory leak fix in act_police, from Davide Caratti.
5) Check RX checksum offload in RX descriptors properly in aquantia
driver, from Dmitry Bogdanov.
6) SKB unlink fix in various spots, from Edward Cree.
7) ndo_dflt_fdb_dump() only works with ethernet, enforce this, from
Eric Dumazet.
8) Fix FID leak in mlxsw driver, from Ido Schimmel.
9) IOTLB locking fix in vhost, from Jean-Philippe Brucker.
10) Fix SKB truesize accounting in ipv4/ipv6/netfilter frag memory
limits otherwise namespace exit can hang. From Jiri Wiesner.
11) Address block parsing length fixes in x25 from Martin Schiller.
12) IRQ and ring accounting fixes in bnxt_en, from Michael Chan.
13) For tun interfaces, only iface delete works with rtnl ops, enforce
this by disallowing add. From Nicolas Dichtel.
14) Use after free in liquidio, from Pan Bian.
15) Fix SKB use after passing to netif_receive_skb(), from Prashant
Bhole.
16) Static key accounting and other fixes in XPS from Sabrina Dubroca.
17) Partially initialized flow key passed to ip6_route_output(), from
Shmulik Ladkani.
18) Fix RTNL deadlock during reset in ibmvnic driver, from Thomas
Falcon.
19) Several small TCP fixes (off-by-one on window probe abort, NULL
deref in tail loss probe, SNMP mis-estimations) from Yuchung
Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
net/sched: cls_flower: Reject duplicated rules also under skip_sw
bnxt_en: Fix _bnxt_get_max_rings() for 57500 chips.
bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.
bnxt_en: Keep track of reserved IRQs.
bnxt_en: Fix CNP CoS queue regression.
net/mlx4_core: Correctly set PFC param if global pause is turned off.
Revert "net/ibm/emac: wrong bit is used for STA control"
neighbour: Avoid writing before skb->head in neigh_hh_output()
ipv6: Check available headroom in ip6_xmit() even without options
tcp: lack of available data can also cause TSO defer
ipv6: sr: properly initialize flowi6 prior passing to ip6_route_output
mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
mlxsw: spectrum_router: Relax GRE decap matching check
mlxsw: spectrum_switchdev: Avoid leaking FID's reference count
mlxsw: spectrum_nve: Remove easily triggerable warnings
ipv4: ipv6: netfilter: Adjust the frag mem limit when truesize changes
sctp: frag_point sanity check
tcp: fix NULL ref in tail loss probe
tcp: Do not underestimate rwnd_limited
net: use skb_list_del_init() to remove from RX sublists
...
GCC 4.6 manual says:
-funit-at-a-time
This option is left for compatibility reasons. -funit-at-a-time has
no effect, while -fno-unit-at-a-time implies -fno-toplevel-reorder
and -fno-section-anchors. Enabled by default.
Remove it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Richard Weinberger <richard@sigma-star.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1541990120-9643-3-git-send-email-yamada.masahiro@socionext.com
The "altmap" is used to provide a pool of memory that is reserved for
the vmemmap backing of hot-plugged memory. This is useful when adding
large amount of ZONE_DEVICE memory to a system with a limited amount of
normal memory.
On ppc64 we use huge pages to map the vmemmap which requires the backing
storage to be contigious and aligned to the hugepage size. The altmap
implementation allows for the altmap provider to reserve a few PFNs at
the start of the range for it's own uses and when this occurs the
first chunk of the altmap is not usable for hugepage mappings. On hash
there is no sane way to fall back to a normal sized page mapping so we
fail the allocation. This results in memory hotplug failing with
ENOMEM when the new range doesn't fall into an existing vmemmap block.
This patch handles this case by falling back to using system memory
rather than failing if we cannot allocate from the altmap. This
fallback should only ever be used for the first vmemmap block so it
should not cause excess memory consumption.
Fixes: 7b73d978a5 ("mm: pass the vmem_altmap to vmemmap_populate")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The interleave set cookie is used to determine if a label stored in the
metadata space should be applied to the current region. This is
important in the case of NVDIMMs since the firmware may change the
interleaving configuration of a DIMM which would invalidate the existing
labels. In our case the hypervisor hides those details from us so we
don't really care, but libnvdimm still requires the interleave set
cookie to be non-zero.
For our purposes we just need the set cookie to be unique and fixed for
a given PAPR SCM region and using the unit-guid (really a UUID) is fine
for this purpose.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Use kernel types (u64)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a new nvdimm device is registered with libnvdimm via
nvdimm_create() it is added as a device on the nvdimm bus. The probe
function for the DIMM driver is potentially quite slow so actually
registering and probing the device is done in an async domain rather
than immediately after device creation. This can result in a race where
the region device (created 2nd) is probed first and fails to activate at
boot.
To fix this we use the same approach as the ACPI/NFIT driver which is to
check that all the DIMM devices registered successfully. LibNVDIMM
provides the nvdimm_bus_count_dimms() function which synchronises with
the async domain and verifies that the dimm was successfully registered
with the bus.
If either of these does not occur then we bail.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The return values of a h-call are returned in the CPU registers and
written to the provided buffer by the plpar_hcall() wrapper. As a result
the values written to memory are always in the native endian and should
not be byte swapped.
The inital implementation of the H-Call interface was done in qemu and
the returned values were byte swapped unnecessarily in both the
hypervisor and in the driver so this was only noticed when bringing up
the PowerVM implementation.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ibm,unit-sizes property was originally specified as an array of two
u32s corresponding to the memory block size, and the number of blocks
available in that region. A fairly last-minute change to the SCM DT
specification was splitting that into two seperate u64 properties:
ibm,block-sizes and ibm,number-of-blocks that convey the same
information. No firmware / hypervisor that emitted the ibm,unit-size
property ever appeared in the wild.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Use kernel types (u32/u64)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix an off-by-one error in the memory resource range. This resource is
used to determine the address range of the memory to be hot-plugged as
ZONE_DEVICE memory. The current end address results in the kernel
attempting to map an additional memblock and the hypervisor may reject
the mapping resulting in the entire hot-plug failing.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Making PAPR_SCM select LIBNVDIMM results in circular dependencies in
Kconfig when another symbol depends on it. Fix this by replacing the
select with a depends.
Fixes: b5beae5e22 ("powerpc/pseries: Add driver for PAPR SCM regions")
Reported-by: Alastair D'Silva <alastair@d-silva.org>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that there are different variants of pt_regs for userspace and
kernel, the uapi for the BPF_PROG_TYPE_PERF_EVENT program type must be
changed by exporting the user_pt_regs structure instead of the pt_regs
structure that is in-kernel only.
Fixes: 002af9391b ("powerpc: Split user/kernel definitions of struct pt_regs")
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These days architectures are mostly out of the business of dealing with
struct scatterlist at all, unless they have architecture specific iommu
drivers. Replace the ARCH_HAS_SG_CHAIN symbol with a ARCH_NO_SG_CHAIN
one only enabled for architectures with horrible legacy iommu drivers
like alpha and parisc, and conditionally for arm which wants to keep it
disable for legacy platforms.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
The powerpc iommu code already returns (~(dma_addr_t)0x0) on mapping
failures, so we can switch over to returning DMA_MAPPING_ERROR and let
the core dma-mapping code handle the rest.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
The dma-direct code already returns (~(dma_addr_t)0x0) on mapping
failures, so we can switch over to returning DMA_MAPPING_ERROR and let
the core dma-mapping code handle the rest.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Memblock list is another source for usable system memory layout.
So move powerpc's arch_kexec_walk_mem() to common code so that other
memblock-based architectures, particularly arm64, can also utilise it.
A moved function is now renamed to kexec_walk_memblock() and integrated
into kexec_locate_mem_hole(), which will now be usable for all
architectures with no need for overriding arch_kexec_walk_mem().
With this change, arch_kexec_walk_mem() need no longer be a weak function,
and was now renamed to kexec_walk_resources().
Since powerpc doesn't support kdump in its kexec_file_load(), the current
kexec_walk_memblock() won't work for kdump either in this form, this will
be fixed in the next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Acked-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In commit 5e9dcb6188 ("powerpc/boot: Expose Kconfig symbols to
wrapper") we added a dependency to serial.c on autoconf.h:
$(obj)/serial.c: $(obj)/autoconf.h
This works when building in-tree (ie. with KBUILD_OUTPUT unset)
because the obj tree is the src tree.
But when building with eg. O=build and -j 1 the build fails:
gcc ... -I../arch/powerpc/boot -c -o arch/powerpc/boot/serial.o arch/powerpc/boot/serial.c
gcc: error: arch/powerpc/boot/serial.c: No such file or directory
Why this is only happening with -j 1 is not clear, when building with
-j greater than 1 somehow we decide to look for serial.c in the src
tree (../), eg:
gcc -I../arch/powerpc/boot -c -o arch/powerpc/boot/serial.o ../arch/powerpc/boot/serial.c
Regardless we shouldn't be specifying a dependency on serial.c in the
build tree, we want to add a dependency to the version in $(srctree)
so fix the rule to say that.
Fixes: 5e9dcb6188 ("powerpc/boot: Expose Kconfig symbols to wrapper")
Tested-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-12-05
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix bpf uapi pointers for 32-bit architectures, from Daniel.
2) improve verifer ability to handle progs with a lot of branches, from Alexei.
3) strict btf checks, from Yonghong.
4) bpf_sk_lookup api cleanup, from Joe.
5) other misc fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The add_ssaaaa, sub_ddmmss, umul_ppmm and udiv_qrnnd macros originate
from GCC's longlong.h which in turn was copied from GMP's longlong.h a
few decades ago.
This was found when compiling with clang:
arch/powerpc/math-emu/fnmsub.c:46:2: error: invalid use of a cast in a
inline asm context requiring an l-value: remove the cast or build with
-fheinous-gnu-extensions
FP_ADD_D(R, T, B);
^~~~~~~~~~~~~~~~~
...
./arch/powerpc/include/asm/sfp-machine.h:283:27: note: expanded from
macro 'sub_ddmmss'
: "=r" ((USItype)(sh)), \
~~~~~~~~~~^~~
Segher points out: this was fixed in GCC over 16 years ago
( https://gcc.gnu.org/r56600 ), and in GMP (where it comes from)
presumably before that.
Update the add_ssaaaa, sub_ddmmss, umul_ppmm and udiv_qrnnd macros to
the latest GCC version in order to git rid of the invalid casts. These
were taken as-is from GCC's longlong in order to make future syncs
obvious. Other parts of sfp-machine.h were left as-is as the file
contains more features than present in longlong.h.
Link: https://github.com/ClangBuiltLinux/linux/issues/260
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
From what I've seen, every time this warning comes up it's bogus,
so let's ignore it.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As this is running with MMU off, the CPU only does speculative
fetch for code in the same page.
Following the significant size reduction of TLB handler routines,
the side handlers can be brought back close to the main part,
ie in the same page.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch reworks the TLB Miss handler in order to not use r12
register, hence avoiding having to save it into SPRN_SPRG_SCRATCH2.
In the DAR Fixup code we can now use SPRN_M_TW, freeing
SPRN_SPRG_SCRATCH2.
Then SPRN_SPRG_SCRATCH2 may be used for something else in the future.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using this HW assistance implies some constraints on the
page table structure:
- Regardless of the main page size used (4k or 16k), the
level 1 table (PGD) contains 1024 entries and each PGD entry covers
a 4Mbytes area which is managed by a level 2 table (PTE) containing
also 1024 entries each describing a 4k page.
- 16k pages require 4 identifical entries in the L2 table
- 512k pages PTE have to be spread every 128 bytes in the L2 table
- 8M pages PTE are at the address pointed by the L1 entry and each
8M page require 2 identical entries in the PGD.
In order to use hardware assistance with 16K pages, this patch does
the following modifications:
- Make PGD size independent of the main page size
- In 16k pages mode, redefine pte_t as a struct with 4 elements,
and populate those 4 elements in __set_pte_at() and pte_update()
- Adapt the size of the hugepage tables.
- Define a PTE_FRAGMENT_NB so that a 16k page contains 4 page tables.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For using 512k pages with hardware assistance, the PTEs have to be spread
every 128 bytes in the L2 table.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today, on the 8xx the TLB handlers do SW tablewalk by doing all
the calculation in ASM, in order to match with the Linux page
table structure.
The 8xx offers hardware assistance which allows significant size
reduction of the TLB handlers, hence also reduces the time spent
in the handlers.
However, using this HW assistance implies some constraints on the
page table structure:
- Regardless of the main page size used (4k or 16k), the
level 1 table (PGD) contains 1024 entries and each PGD entry covers
a 4Mbytes area which is managed by a level 2 table (PTE) containing
also 1024 entries each describing a 4k page.
- 16k pages require 4 identifical entries in the L2 table
- 512k pages PTE have to be spread every 128 bytes in the L2 table
- 8M pages PTE are at the address pointed by the L1 entry and each
8M page require 2 identical entries in the PGD.
This patch modifies the TLB handlers to use HW assistance for 4K PAGES.
Before that patch, the mean time spent in TLB miss handlers is:
- ITLB miss: 80 ticks
- DTLB miss: 62 ticks
After that patch, the mean time spent in TLB miss handlers is:
- ITLB miss: 72 ticks
- DTLB miss: 54 ticks
So the improvement is 10% for ITLB and 13% for DTLB misses
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation of making use of hardware assistance in TLB handlers,
this patch temporarily disables 16K pages and hugepages. The reason
is that when using HW assistance in 4K pages mode, the linux model
fit with the HW model for 4K pages and 8M pages.
However for 16K pages and 512K mode some additional work is needed
to get linux model fit with HW model.
For the 8M pages, they will naturaly come back when we switch to
HW assistance, without any additional handling.
In order to keep the following patch smaller, the removal of the
current special handling for 8M pages gets removed here as well.
Therefore the 4K pages mode will be implemented first and without
support for 512k hugepages. Then the 512k hugepages will be brought
back. And the 16K pages will be implemented in the following step.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to simplify time critical exceptions handling 8xx
specific SW perf counters, this patch moves the counters into
the beginning of memory. This is possible because .text is readable
and the counters are never modified outside of the handlers.
By doing this, we avoid having to set a second register with
the upper part of the address of the counters.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pgtable_cache_add() gracefully handles the case when a cache that
size already exists by returning early with the following test:
if (PGT_CACHE(shift))
return; /* Already have a cache of this size */
It is then not needed to test the existence of the cache before.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of opencoding cache handling for the special case
of hugepage tables having a single pte_t element, this
patch makes use of the common pgtable_cache helpers
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
hugepages uses a cache of order 0. Lets allow page tables
of order 0 in the common part in order to avoid open coding
in hugetlb
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to allow the 8xx to handle pte_fragments, this patch
extends the use of pte_fragments to PPC32 platforms.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to handle pte_fragment functions with single fragment
without adding pte_frag in all mm_context_t, this patch creates
two helpers which do nothing on platforms using a single fragment.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch move pgtable_t into platform headers.
It gets rid of the CONFIG_PPC_64K_PAGES case for PPC64
as nohash/64 doesn't support CONFIG_PPC_64K_PAGES.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The purpose of this patch is to move platform specific
mmu-xxx.h files in platform directories like pte-xxx.h files.
In the meantime this patch creates common nohash and
nohash/32 + nohash/64 mmu.h files for future common parts.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no point in taking the page table lock as pte_frag or
pmd_frag are always NULL when we have only one fragment.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation of next patch which generalises the use of
pte_fragment_alloc() for all, this patch moves the related functions
in a place that is common to all subarches.
The 8xx will need that for supporting 16k pages, as in that mode
page tables still have a size of 4k.
Since pte_fragment with only once fragment is not different
from what is done in the general case, we can easily migrate all
subarchs to pte fragments.
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit 1bc54c0311 ("powerpc: rework 4xx PTE access and TLB miss")
introduced non atomic PTE updates and started the work of removing
PTE updates in TLB miss handlers, but kept PTE_ATOMIC_UPDATES for the
8xx with the following comment:
/* Until my rework is finished, 8xx still needs atomic PTE updates */
commit fe11dc3f96 ("powerpc/8xx: Update TLB asm so it behaves as
linux mm expects") removed all PTE updates done in TLB miss handlers
Therefore, atomic PTE updates are not needed anymore for the 8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a plan to build the kernel with -Wimplicit-fallthrough and these
places in the code produced warnings, but because we build arch/powerpc
with -Werror, they became errors. Fix them up.
This patch produces no change in behaviour, but should be reviewed in
case these are actually bugs not intentional fallthoughs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit f384796c40 ("powerpc/mm: Add support for handling > 512TB address
in SLB miss") removed function slb_miss_bad_addr(struct pt_regs *regs), but
kept its declaration in the prototype file. This patch simply removes the
function definition.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently xmon needs to get devtree_lock (through rtas_token()) during its
invocation (at crash time). If there is a crash while devtree_lock is being
held, then xmon tries to get the lock but spins forever and never get into
the interactive debugger, as in the following case:
int *ptr = NULL;
raw_spin_lock_irqsave(&devtree_lock, flags);
*ptr = 0xdeadbeef;
This patch avoids calling rtas_token(), thus trying to get the same lock,
at crash time. This new mechanism proposes getting the token at
initialization time (xmon_init()) and just consuming it at crash time.
This would allow xmon to be possible invoked independent of devtree_lock
being held or not.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull RCU changes from Paul E. McKenney:
- Convert RCU's BUG_ON() and similar calls to WARN_ON() and similar.
- Replace calls of RCU-bh and RCU-sched update-side functions
to their vanilla RCU counterparts. This series is a step
towards complete removal of the RCU-bh and RCU-sched update-side
functions.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- Documentation updates, including a number of flavor-consolidation
updates from Joel Fernandes.
- Miscellaneous fixes.
- Automate generation of the initrd filesystem used for
rcutorture testing.
- Convert spin_is_locked() assertions to instead use lockdep.
( Note that some of these conversions are going upstream via their
respective maintainers. )
- SRCU updates, especially including a fix from Dennis Krein
for a bag-on-head-class bug.
- RCU torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Instead of running with interrupts disabled, use a semaphore. This should
make it easier for backends that may need to sleep (e.g. EFI) when
performing a write:
|BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
|in_atomic(): 1, irqs_disabled(): 1, pid: 2236, name: sig-xstate-bum
|Preemption disabled at:
|[<ffffffff99d60512>] pstore_dump+0x72/0x330
|CPU: 26 PID: 2236 Comm: sig-xstate-bum Tainted: G D 4.20.0-rc3 #45
|Call Trace:
| dump_stack+0x4f/0x6a
| ___might_sleep.cold.91+0xd3/0xe4
| __might_sleep+0x50/0x90
| wait_for_completion+0x32/0x130
| virt_efi_query_variable_info+0x14e/0x160
| efi_query_variable_store+0x51/0x1a0
| efivar_entry_set_safe+0xa3/0x1b0
| efi_pstore_write+0x109/0x140
| pstore_dump+0x11c/0x330
| kmsg_dump+0xa4/0xd0
| oops_exit+0x22/0x30
...
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Fixes: 21b3ddd39f ("efi: Don't use spinlocks for efi vars")
Signed-off-by: Kees Cook <keescook@chromium.org>
Once the JITed images for each function in a multi-function program
are generated after the first three JIT passes, we only need to fix
the target address for the branch instruction corresponding to each
bpf-to-bpf function call.
This introduces the following optimizations for reducing the work
done by the JIT compiler when handling multi-function programs:
[1] Instead of doing two extra passes to fix the bpf function calls,
do just one as that would be sufficient.
[2] During the extra pass, only overwrite the instruction sequences
for the bpf-to-bpf function calls as everything else would still
remain exactly the same. This also reduces the number of writes
to the JITed image.
[3] Do not regenerate the prologue and the epilogue during the extra
pass as that would be redundant.
Signed-off-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit 78e5dfea84 ("powerpc: dts: replace 'linux,stdout-path' with
'stdout-path'") broke the default console on a number of embedded
PowerPC systems, because it failed to also update the code in
arch/powerpc/kernel/legacy_serial.c to look for that property in
addition to the old one.
This fixes it.
Fixes: 78e5dfea84 ("powerpc: dts: replace 'linux,stdout-path' with 'stdout-path'")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
was introduced by a patch that tried to fix one bug, but by doing so created
another bug. As both bugs corrupt the output (but they do not crash the
kernel), I decided to fix the design such that it could have both bugs
fixed. The original fix, fixed time reporting of the function graph tracer
when doing a max_depth of one. This was code that can test how much the
kernel interferes with userspace. But in doing so, it could corrupt the time
keeping of the function profiler.
The issue is that the curr_ret_stack variable was being used for two
different meanings. One was to keep track of the stack pointer on the
ret_stack (shadow stack used by the function graph tracer), and the other
use case was the graph call depth. Although, the two may be closely
related, where they got updated was the issue that lead to the two different
bugs that required the two use cases to be updated differently.
The big issue with this fix is that it requires changing each architecture.
The good news is, I was able to remove a lot of code that was duplicated
within the architectures and place it into a single location. Then I could
make the fix in one place.
I pushed this code into linux-next to let it settle over a week, and before
doing so, I cross compiled all the affected architectures to make sure that
they built fine.
In the mean time, I also pulled in a patch that fixes the sched_switch
previous tasks state output, that was not actually correct.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCW/4NPhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qnWAAQCyUIRLgYImr81eTl52lxNRsULk+aiI
U29kRFWWU0c40AEA1X9sDF0MgOItbRGfZtnHTZEousXRDaDf4Fge2kF7Egg=
=liQ0
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"While rewriting the function graph tracer, I discovered a design flaw
that was introduced by a patch that tried to fix one bug, but by doing
so created another bug.
As both bugs corrupt the output (but they do not crash the kernel), I
decided to fix the design such that it could have both bugs fixed. The
original fix, fixed time reporting of the function graph tracer when
doing a max_depth of one. This was code that can test how much the
kernel interferes with userspace. But in doing so, it could corrupt
the time keeping of the function profiler.
The issue is that the curr_ret_stack variable was being used for two
different meanings. One was to keep track of the stack pointer on the
ret_stack (shadow stack used by the function graph tracer), and the
other use case was the graph call depth. Although, the two may be
closely related, where they got updated was the issue that lead to the
two different bugs that required the two use cases to be updated
differently.
The big issue with this fix is that it requires changing each
architecture. The good news is, I was able to remove a lot of code
that was duplicated within the architectures and place it into a
single location. Then I could make the fix in one place.
I pushed this code into linux-next to let it settle over a week, and
before doing so, I cross compiled all the affected architectures to
make sure that they built fine.
In the mean time, I also pulled in a patch that fixes the sched_switch
previous tasks state output, that was not actually correct"
* tag 'trace-v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
sched, trace: Fix prev_state output in sched_switch tracepoint
function_graph: Have profiler use curr_ret_stack and not depth
function_graph: Reverse the order of pushing the ret_stack and the callback
function_graph: Move return callback before update of curr_ret_stack
function_graph: Use new curr_ret_depth to manage depth instead of curr_ret_stack
function_graph: Make ftrace_push_return_trace() static
sparc/function_graph: Simplify with function_graph_enter()
sh/function_graph: Simplify with function_graph_enter()
s390/function_graph: Simplify with function_graph_enter()
riscv/function_graph: Simplify with function_graph_enter()
powerpc/function_graph: Simplify with function_graph_enter()
parisc: function_graph: Simplify with function_graph_enter()
nds32: function_graph: Simplify with function_graph_enter()
MIPS: function_graph: Simplify with function_graph_enter()
microblaze: function_graph: Simplify with function_graph_enter()
arm64: function_graph: Simplify with function_graph_enter()
ARM: function_graph: Simplify with function_graph_enter()
x86/function_graph: Simplify with function_graph_enter()
function_graph: Create function_graph_enter() to consolidate architecture code
The arch_teardown_msi_irqs() function assumes that controller ops
pointers were already checked in arch_setup_msi_irqs(), but this
assumption is wrong: arch_teardown_msi_irqs() can be called even when
arch_setup_msi_irqs() returns an error (-ENOSYS).
This can happen in the following scenario:
- msi_capability_init() calls pci_msi_setup_msi_irqs()
- pci_msi_setup_msi_irqs() returns -ENOSYS
- msi_capability_init() notices the error and calls free_msi_irqs()
- free_msi_irqs() calls pci_msi_teardown_msi_irqs()
This is easier to see when CONFIG_PCI_MSI_IRQ_DOMAIN is not set and
pci_msi_setup_msi_irqs() and pci_msi_teardown_msi_irqs() are just
aliases to arch_setup_msi_irqs() and arch_teardown_msi_irqs().
The call to free_msi_irqs() upon pci_msi_setup_msi_irqs() failure
seems legit, as it does additional cleanup; e.g.
list_del(&entry->list) and kfree(entry) inside free_msi_irqs() do
happen (MSI descriptors are allocated before pci_msi_setup_msi_irqs()
is called and need to be cleaned up if that fails).
Fixes: 6b2fd7efeb ("PCI/MSI/PPC: Remove arch_msi_check_device()")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Radu Rendec <radu.rendec@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) ARM64 JIT fixes for subprog handling from Daniel Borkmann.
2) Various sparc64 JIT bug fixes (fused branch convergance, frame
pointer usage detection logic, PSEODU call argument handling).
3) Fix to use BH locking in nf_conncount, from Taehee Yoo.
4) Fix race of TX skb freeing in ipheth driver, from Bernd Eckstein.
5) Handle return value of TX NAPI completion properly in lan743x
driver, from Bryan Whitehead.
6) MAC filter deletion in i40e driver clears wrong state bit, from
Lihong Yang.
7) Fix use after free in rionet driver, from Pan Bian.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
s390/qeth: fix length check in SNMP processing
net: hisilicon: remove unexpected free_netdev
rapidio/rionet: do not free skb before reading its length
i40e: fix kerneldoc for xsk methods
ixgbe: recognize 1000BaseLX SFP modules as 1Gbps
i40e: Fix deletion of MAC filters
igb: fix uninitialized variables
netfilter: nf_tables: deactivate expressions in rule replecement routine
lan743x: Enable driver to work with LAN7431
tipc: fix lockdep warning during node delete
lan743x: fix return value for lan743x_tx_napi_poll
net: via: via-velocity: fix spelling mistake "alignement" -> "alignment"
qed: fix spelling mistake "attnetion" -> "attention"
net: thunderx: fix NULL pointer dereference in nic_remove
sctp: increase sk_wmem_alloc when head->truesize is increased
firestream: fix spelling mistake: "Inititing" -> "Initializing"
net: phy: add workaround for issue where PHY driver doesn't bind to the device
usbnet: ipheth: fix potential recvmsg bug and recvmsg bug 2
sparc: Adjust bpf JIT prologue for PSEUDO calls.
bpf, doc: add entries of who looks over which jits
...
The function_graph_enter() function does the work of calling the function
graph hook function and the management of the shadow stack, simplifying the
work done in the architecture dependent prepare_ftrace_return().
Have powerpc use the new code, and remove the shadow stack management as well as
having to set up the trace structure.
This is needed to prepare for a fix of a design bug on how the curr_ret_stack
is used.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: stable@kernel.org
Fixes: 03274a3ffb ("tracing/fgraph: Adjust fgraph depth before calling trace return callback")
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Make fetching of the BPF call address from ppc64 JIT generic. ppc64
was using a slightly different variant rather than through the insns'
imm field encoding as the target address would not fit into that space.
Therefore, the target subprog number was encoded into the insns' offset
and fetched through fp->aux->func[off]->bpf_func instead. Given there
are other JITs with this issue and the mechanism of fetching the address
is JIT-generic, move it into the core as a helper instead. On the JIT
side, we get information on whether the retrieved address is a fixed
one, that is, not changing through JIT passes, or a dynamic one. For
the former, JITs can optimize their imm emission because this doesn't
change jump offsets throughout JIT process.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Sandipan Das <sandipan@linux.ibm.com>
Tested-by: Sandipan Das <sandipan@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
For some configs the build fails with:
arch/powerpc/mm/dump_linuxpagetables.c: In function 'populate_markers':
arch/powerpc/mm/dump_linuxpagetables.c:306:39: error: 'PKMAP_BASE' undeclared (first use in this function)
arch/powerpc/mm/dump_linuxpagetables.c:314:50: error: 'LAST_PKMAP' undeclared (first use in this function)
These come from highmem.h, including that fixes the build.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 6975a783d7 ("powerpc/boot: Allow building the zImage wrapper
as a relocatable ET_DYN", 2011-04-12) changed the procedure descriptor
at the start of crt0.S to have a hard-coded start address of 0x500000
rather than a reference to _zimage_start, presumably because having
a reference to a symbol introduced a relocation which is awkward to
handle in a position-independent executable. Unfortunately, what is
at 0x500000 in the COFF image is not the first instruction, but the
procedure descriptor itself, that is, a word containing 0x500000,
which is not a valid instruction. Hence, booting a COFF zImage
results in a "DEFAULT CATCH!, code=FFF00700" message from Open
Firmware.
This fixes the problem by (a) putting the procedure descriptor in the
data section and (b) adding a branch to _zimage_start as the first
instruction in the program.
Fixes: 6975a783d7 ("powerpc/boot: Allow building the zImage wrapper as a relocatable ET_DYN")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPC_STD_MMU_32 and PPC_STD_MMU are not used anymore. Remove them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today we have:
config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64
config PPC_STD_MMU
def_bool y
depends on PPC_BOOK3S
PPC_STD_MMU is therefore redundant with PPC_BOOK3S. Lets remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today we have:
config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within a choice]
config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64
config PPC_STD_MMU
def_bool y
depends on PPC_BOOK3S
config PPC_STD_MMU_32
def_bool y
depends on PPC_STD_MMU && PPC32
PPC_STD_MMU_32 is therefore redundant with PPC_BOOK3S_32.
In order to make the code clearer, lets use preferably PPC_BOOK3S_32.
This will allow to remove CONFIG_PPC_STD_MMU_32 in a later patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
asm/book3s/32/pgtable.h is only included when CONFIG_PPC_BOOK3S_32 is set.
Whenever CONFIG_PPC_BOOK3S_32 is set, CONFIG_PPC_STD_MMU_32 is set as well.
This patch removes useless CONFIG_PPC_STD_MMU_32 #ifdefs
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_6xx is not used anymore. Remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Today we have:
config PPC_BOOK3S_32
bool "512x/52xx/6xx/7xx/74xx/82xx/83xx/86xx"
[depends on PPC32 within a choice]
config PPC_BOOK3S
def_bool y
depends on PPC_BOOK3S_32 || PPC_BOOK3S_64
config 6xx
def_bool y
depends on PPC32 && PPC_BOOK3S
6xx is therefore redundant with PPC_BOOK3S_32.
In order to make the code clearer, lets use preferably PPC_BOOK3S_32.
This will allow to remove CONFIG_6xx in a later patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove directly accessing device_node.type pointer and use the
accessors instead. This will eventually allow removing the type
pointer.
Replace the open coded iterating over child nodes with
for_each_child_of_node() while we're here.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove directly accessing device_node.type pointer and use the
accessors instead. This will eventually allow removing the type
pointer.
In the process, the of_stdout pointer can be used instead of finding
the stdout node again.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds new defconfig options for powerpc KVM guest
and guest.config with additional config symbols enabled,
which is to build kernel to boot without initramfs and can be used
as place holder for guest specific additional config symbols in future.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds missing config symbols for ppc64_defconfig
to enable cgroups, memhotplug, numa balancing and XFS
in core kernel image.
Signed-off-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_NR_CPUS is not set in ppc64_defconfig, So it gets default of 32
which is quite small for modern powerpc systems. Instead set a default
of 2048 like other powerpc defconfigs.
Signed-off-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update ppc64_defconfig with savedefconfig. No symbols are added or
removed, this is 100% movement.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 539df7fcb3 ("powerpc/configs: Enable function trace by
default") we added:
CONFIG_FTRACE=y
CONFIG_FUNCTION_TRACER=y
CONFIG_FUNCTION_GRAPH_TRACER=y
To ppc64_defconfig, powernv_defconfig and pseries_defconfig.
But only CONFIG_FUNCTION_TRACER=y is required, CONFIG_FTRACE is
default y if DEBUG_KERNEL is enabled, which we have. And then
CONFIG_FUNCTION_GRAPH_TRACER is default y when CONFIG_FUNCTION_TRACER
is enabled.
The extra symbols were already removed from powernv_defconfig in
commit 9a018fb1e1 ("powerpc/config: powernv_defconfig updates").
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This has a single 1-line patch which fixes a bug in the recently-merged
nested HV KVM support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJb7pbhAAoJEJ2a6ncsY3Gf8UIIAKgiocLz4jTrWYaR/OVbg6EY
tSJQBbsi6bEAog/FZMWDG0zL0YB4s+wXu34RiTt/P7g0VzHFTmR6ZHIJPiSd78aH
oxe8H7TOVq8/EmD0TwREVgUe1qIHgLBkVkk05b0P0nlpeO5bzWQBco2No2mfKWOq
yZcK03QWBsVaq0xhZFM/c0SkxBYOIDcm1kG+XNpOcsmWGXin96TlK+2WohOIH5nY
+16vI61n7/jBjdoxQS0Lw8OAfsA8CjY9GaKf3MuFYe93anZUv2s8FrAv35qUwzBg
5/Y/f+EB5AKMf3XR2A8nJ6HmoeXUFu4NUxT1YAQPAUcrxkENcsaRHDe2Uwt1QIk=
=iPcL
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.20-1' of https://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
PPC KVM fixes for 4.20
This has a single 1-line patch which fixes a bug in the recently-merged
nested HV KVM support.
There is no need to have the 'void __iomem *cpld_base' variable static
since new value always be assigned before use it.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no need to have the 'intoffset' variable static since new value
always be assigned before use it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When compiled for 64-bit, the PD_HUGE constant is a 64-bit integer.
Mark it as an unsigned long.
This squashes over a thousand sparse warnings on my minimal T4240RDB
(e6500, ppc64be) config, of the following 2 forms:
arch/powerpc/include/asm/hugetlb.h:52:49: warning: constant 0x8000000000000000 is so big it is unsigned long
arch/powerpc/include/asm/nohash/pgtable.h:269:49: warning: constant 0x8000000000000000 is so big it is unsigned long
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Type qualifier on return type is ignored. Remove warning in W=1:
arch/powerpc/include/asm/book3s/64/pgtable.h:1268:25: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When both `CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y` and `CONFIG_UBSAN=y`
are set, link step typically produce numberous warnings about orphan
section:
+ powerpc-linux-gnu-ld -EB -m elf32ppc -Bstatic --orphan-handling=warn --build-id --gc-sections -X -o .tmp_vmlinux1 -T ./arch/powerpc/kernel/vmlinux.lds --who
le-archive built-in.a --no-whole-archive --start-group lib/lib.a --end-group
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_data393' from `init/main.o' being placed in section `.data..Lubsan_data393'.
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_data394' from `init/main.o' being placed in section `.data..Lubsan_data394'.
...
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_type11' from `init/main.o' being placed in section `.data..Lubsan_type11'.
powerpc-linux-gnu-ld: warning: orphan section `.data..Lubsan_type12' from `init/main.o' being placed in section `.data..Lubsan_type12'.
...
This commit remove those warnings produced at W=1.
Link: https://www.mail-archive.com/linuxppc-dev@lists.ozlabs.org/msg135407.html
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function huge_ptep_set_access_flags() has the 'extern' keyword in the
function definition and also in the function declaration. This causes a
warning in 'sparse' since the 'extern' storage class should not be used
in the function definition.
arch/powerpc/mm/pgtable.c:232:12: warning: function 'huge_ptep_set_access_flags' with external linkage has definition
This patch removes the keyword from the definition part. It also removes
the extern keyword from the declaration part, since checkpatch --strict
complains about it.
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sparse tool is showing some warnings on pkeys.c file, mainly related to
storage class identifiers. There are static variables and functions not
declared as such. The same thing happens with an extern function, which
misses the header inclusion.
arch/powerpc/mm/pkeys.c:14:6: warning: symbol 'pkey_execute_disable_supported' was not declared. Should it be static?
arch/powerpc/mm/pkeys.c:16:6: warning: symbol 'pkeys_devtree_defined' was not declared. Should it be static?
arch/powerpc/mm/pkeys.c:19:6: warning: symbol 'pkey_amr_mask' was not declared. Should it be static?
arch/powerpc/mm/pkeys.c:20:6: warning: symbol 'pkey_iamr_mask' was not declared. Should it be static?
arch/powerpc/mm/pkeys.c:21:6: warning: symbol 'pkey_uamor_mask' was not declared. Should it be static?
arch/powerpc/mm/pkeys.c:22:6: warning: symbol 'execute_only_key' was not declared. Should it be static?
arch/powerpc/mm/pkeys.c:60:5: warning: symbol 'pkey_initialize' was not declared. Should it be static?
arch/powerpc/mm/pkeys.c:404:6: warning: symbol 'arch_vma_access_permitted' was not declared. Should it be static?
This patch fix al the warning, basically turning all global variables that
are not declared as extern at asm/pkeys.h into static.
It also includes asm/mmu_context.h header, which contains the definition of
arch_vma_access_permitted.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are three symbols (two variables and a function) that are being used
solely in the same file (imc-pmu.c), thus, these symbols should be static,
but they are not. This was detected by sparse:
arch/powerpc/perf/imc-pmu.c:31:20: warning: symbol 'nest_imc_refc' was not declared. Should it be static?
arch/powerpc/perf/imc-pmu.c:37:20: warning: symbol 'core_imc_refc' was not declared. Should it be static?
arch/powerpc/perf/imc-pmu.c:46:16: warning: symbol 'imc_event_to_pmu' was not declared. Should it be static?
This patch simply adds the 'static' storage-class definition to these
symbols, thus, restricting their usage only in the imc-pmu.c file.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function scom_map_device() returns data type 'scom_map_t', which is a
typedef for 'void *'. This functions is currently returning NULL and zero,
which causes the following warning by 'sparse':
arch/powerpc/sysdev/scom.c:63:24: warning: Using plain integer as NULL pointer
arch/powerpc/sysdev/scom.c:86:24: warning: Using plain integer as NULL pointer
This patch simply replaces zero by NULL.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Functions do_stf_{entry,exit}_barrier_fixups are static but not declared as
such. This was detected by `sparse` tool with the following warning:
arch/powerpc/lib/feature-fixups.c:121:6: warning: symbol 'do_stf_entry_barrier_fixups' was not declared. Should it be static?
arch/powerpc/lib/feature-fixups.c:171:6: warning: symbol 'do_stf_exit_barrier_fixups' was not declared. Should it be static?
This patch declares both functions as static, as they are only called by
do_stf_barrier_fixups(), which is in the same source code file.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently sparse is complaining about three issues on the xmon code. Two
storage classes issues and a dereferencing a 'noderef' pointer. These are
the warnings:
arch/powerpc/xmon/xmon.c:2783:1: warning: symbol 'dump_log_buf' was not declared. Should it be static?
arch/powerpc/xmon/xmon.c:2989:6: warning: symbol 'format_pte' was not declared. Should it be static?
arch/powerpc/xmon/xmon.c:2983:30: warning: dereference of noderef expression
This patch fixes all of them, turning both functions static and
dereferencing a pointer calling rcu_dereference() instead of a
straightforward dereference.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sparse shows that xive_do_source_eoi() file is defined without any
declaration, thus, it should be a static function.
arch/powerpc/sysdev/xive/common.c:312:6: warning: symbol 'xive_do_source_eoi' was not declared. Should it be static?
This patch simply turns this symbol into static.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Function pci_ers_result_name() is a static function, although not declared
as such. This was detected by sparse in the following warning
arch/powerpc/kernel/eeh_driver.c:63:12: warning: symbol 'pci_ers_result_name' was not declared. Should it be static?
This patch simply declares the function a static.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Current powerpc security.c file is defining functions, as
cpu_show_meltdown(), cpu_show_spectre_v{1,2} and others, that are being
declared at linux/cpu.h header without including the header file that
contains these declarations.
This is being reported by sparse, which thinks that these functions are
static, due to the lack of declaration:
arch/powerpc/kernel/security.c:105:9: warning: symbol 'cpu_show_meltdown' was not declared. Should it be static?
arch/powerpc/kernel/security.c:139:9: warning: symbol 'cpu_show_spectre_v1' was not declared. Should it be static?
arch/powerpc/kernel/security.c:161:9: warning: symbol 'cpu_show_spectre_v2' was not declared. Should it be static?
arch/powerpc/kernel/security.c:209:6: warning: symbol 'stf_barrier' was not declared. Should it be static?
arch/powerpc/kernel/security.c:289:9: warning: symbol 'cpu_show_spec_store_bypass' was not declared. Should it be static?
This patch simply includes the proper header (linux/cpu.h) to match
function definition and declaration.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Let architectures opt into EISA support by selecting HAVE_EISA and
handle everything else in drivers/eisa.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no good reason to duplicate the RAPIDIO menu in various
architectures. Instead provide a selectable HAVE_RAPIDIO symbol
that indicates native availability of RAPIDIO support and the handle
the rest in drivers/pci. This also means we now provide support
for PCI(e) to Rapidio bridges for every architecture instead of a
limited subset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is nothing architecture specific in the PCMCIA core, so allow
building it everywhere. The actual host controllers will depend on ISA,
PCI or a specific SOC.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Let architectures select the syscall support instead of duplicating the
kconfig entry.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the definitions to drivers/pci and let the architectures select
them. Two small differences to before: PCI_DOMAINS_GENERIC now selects
PCI_DOMAINS, cutting down the churn for modern architectures. As the
only architectured arm did previously also offer PCI_DOMAINS as a user
visible choice in addition to selecting it from the relevant configs,
this is gone now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no good reason to duplicate the PCI menu in every architecture.
Instead provide a selectable HAVE_PCI symbol that indicates availability
of PCI support, and a FORCE_PCI symbol to for PCI on and the handle the
rest in drivers/pci.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace VLAN_TAG_PRESENT with single bit flag and free up
VLAN.CFI overload. Now VLAN.CFI is visible in networking stack
and can be passed around intact.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c2de74cc8 ("powerpc/64: Interrupts save PPR on stack rather
than thread_struct") changed sizeof(struct pt_regs) % 16 from 0 to 8,
which causes the interrupt frame allocation on kernel entry to put the
kernel stack out of alignment.
Quadword (16-byte) alignment for the stack is required by both the
64-bit v1 ABI (v1.9 § 3.2.2) and the 64-bit v2 ABI (v1.1 § 2.2.2.1).
Add a pad field to fix alignment, and add a BUILD_BUG_ON to catch this
in future.
Fixes: 4c2de74cc8 ("powerpc/64: Interrupts save PPR on stack rather than thread_struct")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While running a nested guest VCPU on L0 via H_ENTER_NESTED hcall, a
pending signal in the L0 QEMU process can generate the following
sequence:
ret0 = kvmppc_pseries_do_hcall()
ret1 = kvmhv_enter_nested_guest()
ret2 = kvmhv_run_single_vcpu()
if (ret2 == -EINTR)
return H_INTERRUPT
if (ret1 == H_INTERRUPT)
kvmppc_set_gpr(vcpu, 3, 0)
return -EINTR
/* skipped: */
kvmppc_set_gpr(vcpu, 3, ret)
vcpu->arch.hcall_needed = 0
return RESUME_GUEST
which causes an exit to L0 userspace with ret0 == -EINTR.
The intention seems to be to set the hcall return value to 0 (via
VCPU r3) so that L1 will see a successful return from H_ENTER_NESTED
once we resume executing the VCPU. However, because we don't set
vcpu->arch.hcall_needed = 0, we do the following once userspace
resumes execution via kvm_arch_vcpu_ioctl_run():
...
} else if (vcpu->arch.hcall_needed) {
int i
kvmppc_set_gpr(vcpu, 3, run->papr_hcall.ret);
for (i = 0; i < 9; ++i)
kvmppc_set_gpr(vcpu, 4 + i, run->papr_hcall.args[i]);
vcpu->arch.hcall_needed = 0;
since vcpu->arch.hcall_needed == 1 indicates that userspace should
have handled the hcall and stored the return value in
run->papr_hcall.ret. Since that's not the case here, we can get an
unexpected value in VCPU r3, which can result in
kvmhv_p9_guest_entry() reporting an unexpected trap value when it
returns from H_ENTER_NESTED, causing the following register dump to
console via subsequent call to kvmppc_handle_exit_hv() in L1:
[ 350.612854] vcpu 00000000f9564cf8 (0):
[ 350.612915] pc = c00000000013eb98 msr = 8000000000009033 trap = 1
[ 350.613020] r 0 = c0000000004b9044 r16 = 0000000000000000
[ 350.613075] r 1 = c00000007cffba30 r17 = 0000000000000000
[ 350.613120] r 2 = c00000000178c100 r18 = 00007fffc24f3b50
[ 350.613166] r 3 = c00000007ef52480 r19 = 00007fffc24fff58
[ 350.613212] r 4 = 0000000000000000 r20 = 00000a1e96ece9d0
[ 350.613253] r 5 = 70616d00746f6f72 r21 = 00000a1ea117c9b0
[ 350.613295] r 6 = 0000000000000020 r22 = 00000a1ea1184360
[ 350.613338] r 7 = c0000000783be440 r23 = 0000000000000003
[ 350.613380] r 8 = fffffffffffffffc r24 = 00000a1e96e9e124
[ 350.613423] r 9 = c00000007ef52490 r25 = 00000000000007ff
[ 350.613469] r10 = 0000000000000004 r26 = c00000007eb2f7a0
[ 350.613513] r11 = b0616d0009eccdb2 r27 = c00000007cffbb10
[ 350.613556] r12 = c0000000004b9000 r28 = c00000007d83a2c0
[ 350.613597] r13 = c000000001b00000 r29 = c0000000783cdf68
[ 350.613639] r14 = 0000000000000000 r30 = 0000000000000000
[ 350.613681] r15 = 0000000000000000 r31 = c00000007cffbbf0
[ 350.613723] ctr = c0000000004b9000 lr = c0000000004b9044
[ 350.613765] srr0 = 0000772f954dd48c srr1 = 800000000280f033
[ 350.613808] sprg0 = 0000000000000000 sprg1 = c000000001b00000
[ 350.613859] sprg2 = 0000772f9565a280 sprg3 = 0000000000000000
[ 350.613911] cr = 88002848 xer = 0000000020040000 dsisr = 42000000
[ 350.613962] dar = 0000772f95390000
[ 350.614031] fault dar = c000000244b278c0 dsisr = 00000000
[ 350.614073] SLB (0 entries):
[ 350.614157] lpcr = 0040000003d40413 sdr1 = 0000000000000000 last_inst = ffffffff
[ 350.614252] trap=0x1 | pc=0xc00000000013eb98 | msr=0x8000000000009033
followed by L1's QEMU reporting the following before stopping execution
of the nested guest:
KVM: unknown exit, hardware reason 1
NIP c00000000013eb98 LR c0000000004b9044 CTR c0000000004b9000 XER 0000000020040000 CPU#0
MSR 8000000000009033 HID0 0000000000000000 HF 8000000000000000 iidx 3 didx 3
TB 00000000 00000000 DECR 00000000
GPR00 c0000000004b9044 c00000007cffba30 c00000000178c100 c00000007ef52480
GPR04 0000000000000000 70616d00746f6f72 0000000000000020 c0000000783be440
GPR08 fffffffffffffffc c00000007ef52490 0000000000000004 b0616d0009eccdb2
GPR12 c0000000004b9000 c000000001b00000 0000000000000000 0000000000000000
GPR16 0000000000000000 0000000000000000 00007fffc24f3b50 00007fffc24fff58
GPR20 00000a1e96ece9d0 00000a1ea117c9b0 00000a1ea1184360 0000000000000003
GPR24 00000a1e96e9e124 00000000000007ff c00000007eb2f7a0 c00000007cffbb10
GPR28 c00000007d83a2c0 c0000000783cdf68 0000000000000000 c00000007cffbbf0
CR 88002848 [ L L - - E L G L ] RES ffffffffffffffff
SRR0 0000772f954dd48c SRR1 800000000280f033 PVR 00000000004e1202 VRSAVE 0000000000000000
SPRG0 0000000000000000 SPRG1 c000000001b00000 SPRG2 0000772f9565a280 SPRG3 0000000000000000
SPRG4 0000000000000000 SPRG5 0000000000000000 SPRG6 0000000000000000 SPRG7 0000000000000000
HSRR0 0000000000000000 HSRR1 0000000000000000
CFAR 0000000000000000
LPCR 0000000003d40413
PTCR 0000000000000000 DAR 0000772f95390000 DSISR 0000000042000000
Fix this by setting vcpu->arch.hcall_needed = 0 to indicate completion
of H_ENTER_NESTED before we exit to L0 userspace.
Fixes: 360cae3137 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Cc: linuxppc-dev@ozlabs.org
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When VPHN function is not supported and during cpu hotplug event,
kernel prints message 'VPHN function not supported. Disabling
polling...'. Currently it prints on every hotplug event, it floods
dmesg when a KVM guest tries to hotplug huge number of vcpus, let's
just print once and suppress further kernel prints.
Signed-off-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Clang needs to be told which target it is building for when cross
compiling.
Link: https://github.com/ClangBuiltLinux/linux/issues/259
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Daniel Axtens <dja@axtens.net> # powerpc 64-bit BE
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Back in 2006 Ben added some workarounds for a misbehaviour in the
Spider IO bridge used on early Cell machines, see commit
014da7ff47 ("[POWERPC] Cell "Spider" MMIO workarounds"). Later these
were made to be generic, ie. not tied specifically to Spider.
The code stashes a token in the high bits (59-48) of virtual addresses
used for IO (eg. returned from ioremap()). This works fine when using
the Hash MMU, but when we're using the Radix MMU the bits used for the
token overlap with some of the bits of the virtual address.
This is because the maximum virtual address is larger with Radix, up
to c00fffffffffffff, and in fact we use that high part of the address
range for ioremap(), see RADIX_KERN_IO_START.
As it happens the bits that are used overlap with the bits that
differentiate an IO address vs a linear map address. If the resulting
address lies outside the linear mapping we will crash (see below), if
not we just corrupt memory.
virtio-pci 0000:00:00.0: Using 64-bit direct DMA at offset 800000000000000
Unable to handle kernel paging request for data at address 0xc000000080000014
...
CFAR: c000000000626b98 DAR: c000000080000014 DSISR: 42000000 IRQMASK: 0
GPR00: c0000000006c54fc c00000003e523378 c0000000016de600 0000000000000000
GPR04: c00c000080000014 0000000000000007 0fffffff000affff 0000000000000030
^^^^
...
NIP [c000000000626c5c] .iowrite8+0xec/0x100
LR [c0000000006c992c] .vp_reset+0x2c/0x90
Call Trace:
.pci_bus_read_config_dword+0xc4/0x120 (unreliable)
.register_virtio_device+0x13c/0x1c0
.virtio_pci_probe+0x148/0x1f0
.local_pci_probe+0x68/0x140
.pci_device_probe+0x164/0x220
.really_probe+0x274/0x3b0
.driver_probe_device+0x80/0x170
.__driver_attach+0x14c/0x150
.bus_for_each_dev+0xb8/0x130
.driver_attach+0x34/0x50
.bus_add_driver+0x178/0x2f0
.driver_register+0x90/0x1a0
.__pci_register_driver+0x6c/0x90
.virtio_pci_driver_init+0x2c/0x40
.do_one_initcall+0x64/0x280
.kernel_init_freeable+0x36c/0x474
.kernel_init+0x24/0x160
.ret_from_kernel_thread+0x58/0x7c
This hasn't been a problem because CONFIG_PPC_IO_WORKAROUNDS which
enables this code is usually not enabled. It is only enabled when it's
selected by PPC_CELL_NATIVE which is only selected by
PPC_IBM_CELL_BLADE and that in turn depends on BIG_ENDIAN. So in order
to hit the bug you need to build a big endian kernel, with IBM Cell
Blade support enabled, as well as Radix MMU support, and then boot
that on Power9 using Radix MMU.
Still we can fix the bug, so let's do that. We simply use fewer bits
for the token, taking the union of the restrictions on the address
from both Hash and Radix, we end up with 8 bits we can use for the
token. The only user of the token is iowa_mem_find_bus() which only
supports 8 token values, so 8 bits is plenty for that.
Fixes: 566ca99af0 ("powerpc/mm/radix: Add dummy radix_enabled()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With preempt enabled we see warnings in do_slb_fault():
BUG: using smp_processor_id() in preemptible [00000000] code: kworker/u33:0/98
futex hash table entries: 4096 (order: 3, 524288 bytes)
caller is do_slb_fault+0x204/0x230
CPU: 5 PID: 98 Comm: kworker/u33:0 Not tainted 4.19.0-rc3-gcc-7.3.1-00022-g1936f094e164 #138
Call Trace:
dump_stack+0xb4/0x104 (unreliable)
check_preemption_disabled+0x148/0x150
do_slb_fault+0x204/0x230
data_access_slb_common+0x138/0x180
This is caused by the get_paca() in slb_allocate_kernel(), which
includes a call to debug_smp_processor_id().
slb_allocate_kernel() can only be called from do_slb_fault(), and in
that path interrupts are hard disabled and so we can't be preempted,
but we can't update the preempt flags (in thread_info) because that
could cause an SLB fault.
So just use local_paca which is safe and doesn't cause the warning.
Fixes: 48e7b76957 ("powerpc/64s/hash: Convert SLB miss handlers to C")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The previous commit, "of: overlay: add missing of_node_get() in
__of_attach_node_sysfs" added a missing of_node_get() to
__of_attach_node_sysfs(). This results in a refcount imbalance
for nodes attached with dlpar_attach_node(). The calling sequence
from dlpar_attach_node() to __of_attach_node_sysfs() is:
dlpar_attach_node()
of_attach_node()
__of_attach_node_sysfs()
For more detailed description of the node refcount, see
commit 68baf692c4 ("powerpc/pseries: Fix of_node_put() underflow
during DLPAR remove").
Tested-by: Alan Tull <atull@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Now that call_rcu()'s callback is not invoked until after all
preempt-disable regions of code have completed (in addition to explicitly
marked RCU read-side critical sections), call_rcu() can be used in place
of call_rcu_sched(). This commit therefore makes that change.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: <linuxppc-dev@lists.ozlabs.org>
TRACE_INCLUDE_PATH and TRACE_INCLUDE_FILE are used by
<trace/define_trace.h>, so like that #include, they should
be outside #ifdef protection.
They also need to be #undefed before defining, in case multiple trace
headers are included by the same C file. This became the case on
book3e after commit cf4a608515 ("powerpc/mm: Add missing tracepoint for
tlbie"), leading to the following build error:
CC arch/powerpc/kvm/powerpc.o
In file included from arch/powerpc/kvm/powerpc.c:51:0:
arch/powerpc/kvm/trace.h:9:0: error: "TRACE_INCLUDE_PATH" redefined
[-Werror]
#define TRACE_INCLUDE_PATH .
^
In file included from arch/powerpc/kvm/../mm/mmu_decl.h:25:0,
from arch/powerpc/kvm/powerpc.c:48:
./arch/powerpc/include/asm/trace.h:224:0: note: this is the location of
the previous definition
#define TRACE_INCLUDE_PATH asm
^
cc1: all warnings being treated as errors
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The slbfee instruction was only added in ISA 2.05 (Power6), it's not
supported on older CPUs. We don't have a CPU feature for that ISA
version though, so just use the ISA 2.06 feature flag.
Fixes: e15a4fea4d ("powerpc/64s/hash: Add some SLB debugging tests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Old toolchains don't know about slbfee and break the build, eg:
{standard input}:37: Error: Unrecognized opcode: `slbfee.'
Fix it by using the macro version. We need to add an underscore
version that takes raw register numbers from the inline asm, rather
than our Rx macros.
Fixes: e15a4fea4d ("powerpc/64s/hash: Add some SLB debugging tests")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code for assert_slb_exists() and assert_slb_notexists() is almost
identical, except for the polarity of the WARN_ON(). In a future patch
we'll need to modify this code, so consolidate it now into a single
function.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The NPU IOMMU is setup to mirror the parent PCIe device IOMMU
setup. Therefore it does not make sense to call dma operations such as
dma_map_page(), etc. directly on these devices. The existing dma_ops
simply print a warning if they are ever called, however this is
unnecessary and the warnings are likely to go unnoticed.
It is instead simpler to remove these operations and let the generic
DMA code print warnings (eg. via a NULL pointer deref) in cases of
buggy drivers attempting dma operations on NVLink devices.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some things that I missed due to travel, or that came in late.
Two fixes also going to stable:
- A revert of a buggy change to the 8xx TLB miss handlers.
- Our flushing of SPE (Signal Processing Engine) registers on fork was broken.
Other changes:
- A change to the KVM decrementer emulation to use proper APIs.
- Some cleanups to the way we do code patching in the 8xx code.
- Expose the maximum possible memory for the system in /proc/powerpc/lparcfg.
- Merge some updates from Scott: "a couple device tree updates, and a fix for a
missing prototype warning."
A few other minor fixes and a handful of fixes for our selftests.
Thanks to:
Aravinda Prasad, Breno Leitao, Camelia Groza, Christophe Leroy, Felipe Rechia,
Joel Stanley, Naveen N. Rao, Paul Mackerras, Scott Wood, Tyrel Datwyler.
-----BEGIN PGP SIGNATURE-----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=VCkW
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some things that I missed due to travel, or that came in late.
Two fixes also going to stable:
- A revert of a buggy change to the 8xx TLB miss handlers.
- Our flushing of SPE (Signal Processing Engine) registers on fork
was broken.
Other changes:
- A change to the KVM decrementer emulation to use proper APIs.
- Some cleanups to the way we do code patching in the 8xx code.
- Expose the maximum possible memory for the system in
/proc/powerpc/lparcfg.
- Merge some updates from Scott: "a couple device tree updates, and a
fix for a missing prototype warning"
A few other minor fixes and a handful of fixes for our selftests.
Thanks to: Aravinda Prasad, Breno Leitao, Camelia Groza, Christophe
Leroy, Felipe Rechia, Joel Stanley, Naveen N. Rao, Paul Mackerras,
Scott Wood, Tyrel Datwyler"
* tag 'powerpc-4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (21 commits)
selftests/powerpc: Fix compilation issue due to asm label
selftests/powerpc/cache_shape: Fix out-of-tree build
selftests/powerpc/switch_endian: Fix out-of-tree build
selftests/powerpc/pmu: Link ebb tests with -no-pie
selftests/powerpc/signal: Fix out-of-tree build
selftests/powerpc/ptrace: Fix out-of-tree build
powerpc/xmon: Relax frame size for clang
selftests: powerpc: Fix warning for security subdir
selftests/powerpc: Relax L1d miss targets for rfi_flush test
powerpc/process: Fix flush_all_to_thread for SPE
powerpc/pseries: add missing cpumask.h include file
selftests/powerpc: Fix ptrace tm failure
KVM: PPC: Use exported tb_to_ns() function in decrementer emulation
powerpc/pseries: Export maximum memory value
powerpc/8xx: Use patch_site for perf counters setup
powerpc/8xx: Use patch_site for memory setup patching
powerpc/code-patching: Add a helper to get the address of a patch_site
Revert "powerpc/8xx: Use L1 entry APG to handle _PAGE_ACCESSED for CONFIG_SWAP"
powerpc/8xx: add missing header in 8xx_mmu.c
powerpc/8xx: Add DT node for using the SEC engine of the MPC885
...
Evaluating cc-name invokes the compiler every time even when you are
not compiling anything, like 'make help'. This is not efficient.
The compiler type has been already detected in the Kconfig stage.
Use CONFIG_CC_IS_CLANG, instead.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Paul Burton <paul.burton@mips.com> (MIPS)
Acked-by: Joel Stanley <joel@jms.id.au>
Various powerpc boards select the PCI_MSI config option without selecting
PCI, resulting in potentially not compilable configurations if the by
default enabled PCI option is disabled. Explicitly select PCI to ensure
we always have valid configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This option isn't actually used anywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Let's perform all checking + offlining + removing under
device_hotplug_lock, so nobody can mess with these devices via sysfs
concurrently.
[david@redhat.com: take device_hotplug_lock outside of loop]
Link: http://lkml.kernel.org/r/20180927092554.13567-6-david@redhat.com
Link: http://lkml.kernel.org/r/20180925091457.28651-6-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rashmica Gupta <rashmica.g@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
device_online() should be called with device_hotplug_lock() held.
Link: http://lkml.kernel.org/r/20180925091457.28651-5-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rashmica Gupta <rashmica.g@gmail.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add_memory() currently does not take the device_hotplug_lock, however
is aleady called under the lock from
arch/powerpc/platforms/pseries/hotplug-memory.c
drivers/acpi/acpi_memhotplug.c
to synchronize against CPU hot-remove and similar.
In general, we should hold the device_hotplug_lock when adding memory to
synchronize against online/offline request (e.g. from user space) - which
already resulted in lock inversions due to device_lock() and
mem_hotplug_lock - see 30467e0b3b ("mm, hotplug: fix concurrent memory
hot-add deadlock"). add_memory()/add_memory_resource() will create memory
block devices, so this really feels like the right thing to do.
Holding the device_hotplug_lock makes sure that a memory block device
can really only be accessed (e.g. via .online/.state) from user space,
once the memory has been fully added to the system.
The lock is not held yet in
drivers/xen/balloon.c
arch/powerpc/platforms/powernv/memtrace.c
drivers/s390/char/sclp_cmd.c
drivers/hv/hv_balloon.c
So, let's either use the locked variants or take the lock.
Don't export add_memory_resource(), as it once was exported to be used by
XEN, which is never built as a module. If somebody requires it, we also
have to export a locked variant (as device_hotplug_lock is never
exported).
Link: http://lkml.kernel.org/r/20180925091457.28651-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: online/offline_pages called w.o. mem_hotplug_lock", v3.
Reading through the code and studying how mem_hotplug_lock is to be used,
I noticed that there are two places where we can end up calling
device_online()/device_offline() - online_pages()/offline_pages() without
the mem_hotplug_lock. And there are other places where we call
device_online()/device_offline() without the device_hotplug_lock.
While e.g.
echo "online" > /sys/devices/system/memory/memory9/state
is fine, e.g.
echo 1 > /sys/devices/system/memory/memory9/online
Will not take the mem_hotplug_lock. However the device_lock() and
device_hotplug_lock.
E.g. via memory_probe_store(), we can end up calling
add_memory()->online_pages() without the device_hotplug_lock. So we can
have concurrent callers in online_pages(). We e.g. touch in
online_pages() basically unprotected zone->present_pages then.
Looks like there is a longer history to that (see Patch #2 for details),
and fixing it to work the way it was intended is not really possible. We
would e.g. have to take the mem_hotplug_lock in device/base/core.c, which
sounds wrong.
Summary: We had a lock inversion on mem_hotplug_lock and device_lock().
More details can be found in patch 3 and patch 6.
I propose the general rules (documentation added in patch 6):
1. add_memory/add_memory_resource() must only be called with
device_hotplug_lock.
2. remove_memory() must only be called with device_hotplug_lock. This is
already documented and holds for all callers.
3. device_online()/device_offline() must only be called with
device_hotplug_lock. This is already documented and true for now in core
code. Other callers (related to memory hotplug) have to be fixed up.
4. mem_hotplug_lock is taken inside of add_memory/remove_memory/
online_pages/offline_pages.
To me, this looks way cleaner than what we have right now (and easier to
verify). And looking at the documentation of remove_memory, using
lock_device_hotplug also for add_memory() feels natural.
This patch (of 6):
remove_memory() is exported right now but requires the
device_hotplug_lock, which is not exported. So let's provide a variant
that takes the lock and only export that one.
The lock is already held in
arch/powerpc/platforms/pseries/hotplug-memory.c
drivers/acpi/acpi_memhotplug.c
arch/powerpc/platforms/powernv/memtrace.c
Apart from that, there are not other users in the tree.
Link: http://lkml.kernel.org/r/20180925091457.28651-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Pavel Tatashin <pavel.tatashin@microsoft.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Rashmica Gupta <rashmica.g@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: YASUAKI ISHIMATSU <yasu.isimatu@gmail.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a memblock allocation APIs are called with align = 0, the alignment
is implicitly set to SMP_CACHE_BYTES.
Implicit alignment is done deep in the memblock allocator and it can
come as a surprise. Not that such an alignment would be wrong even
when used incorrectly but it is better to be explicit for the sake of
clarity and the prinicple of the least surprise.
Replace all such uses of memblock APIs with the 'align' parameter
explicitly set to SMP_CACHE_BYTES and stop implicit alignment assignment
in the memblock internal allocation functions.
For the case when memblock APIs are used via helper functions, e.g. like
iommu_arena_new_node() in Alpha, the helper functions were detected with
Coccinelle's help and then manually examined and updated where
appropriate.
The direct memblock APIs users were updated using the semantic patch below:
@@
expression size, min_addr, max_addr, nid;
@@
(
|
- memblock_alloc_try_nid_raw(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_raw(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid_nopanic(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid_nopanic(size, SMP_CACHE_BYTES, min_addr, max_addr,
nid)
|
- memblock_alloc_try_nid(size, 0, min_addr, max_addr, nid)
+ memblock_alloc_try_nid(size, SMP_CACHE_BYTES, min_addr, max_addr, nid)
|
- memblock_alloc(size, 0)
+ memblock_alloc(size, SMP_CACHE_BYTES)
|
- memblock_alloc_raw(size, 0)
+ memblock_alloc_raw(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from(size, 0, min_addr)
+ memblock_alloc_from(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_nopanic(size, 0)
+ memblock_alloc_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low(size, 0)
+ memblock_alloc_low(size, SMP_CACHE_BYTES)
|
- memblock_alloc_low_nopanic(size, 0)
+ memblock_alloc_low_nopanic(size, SMP_CACHE_BYTES)
|
- memblock_alloc_from_nopanic(size, 0, min_addr)
+ memblock_alloc_from_nopanic(size, SMP_CACHE_BYTES, min_addr)
|
- memblock_alloc_node(size, 0, nid)
+ memblock_alloc_node(size, SMP_CACHE_BYTES, nid)
)
[mhocko@suse.com: changelog update]
[akpm@linux-foundation.org: coding-style fixes]
[rppt@linux.ibm.com: fix missed uses of implicit alignment]
Link: http://lkml.kernel.org/r/20181016133656.GA10925@rapoport-lnx
Link: http://lkml.kernel.org/r/1538687224-17535-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Acked-by: Paul Burton <paul.burton@mips.com> [MIPS]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make it explicit that the caller gets a physical address rather than a
virtual one.
This will also allow using meblock_alloc prefix for memblock allocations
returning virtual address, which is done in the following patches.
The conversion is done using the following semantic patch:
@@
expression e1, e2, e3;
@@
(
- memblock_alloc(e1, e2)
+ memblock_phys_alloc(e1, e2)
|
- memblock_alloc_nid(e1, e2, e3)
+ memblock_phys_alloc_nid(e1, e2, e3)
|
- memblock_alloc_try_nid(e1, e2, e3)
+ memblock_phys_alloc_try_nid(e1, e2, e3)
)
Link: http://lkml.kernel.org/r/1536927045-23536-7-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architecures use memblock for early memory management. There is no need
for the CONFIG_HAVE_MEMBLOCK configuration option.
[rppt@linux.vnet.ibm.com: of/fdt: fixup #ifdefs]
Link: http://lkml.kernel.org/r/20180919103457.GA20545@rapoport-lnx
[rppt@linux.vnet.ibm.com: csky: fixups after bootmem removal]
Link: http://lkml.kernel.org/r/20180926112744.GC4628@rapoport-lnx
[rppt@linux.vnet.ibm.com: remove stale #else and the code it protects]
Link: http://lkml.kernel.org/r/1538067825-24835-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1536927045-23536-4-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All achitectures select NO_BOOTMEM which essentially becomes 'Y' for any
kernel configuration and therefore it can be removed.
[alexander.h.duyck@linux.intel.com: remove now defunct NO_BOOTMEM from depends list for deferred init]
Link: http://lkml.kernel.org/r/20180925201814.3576.15105.stgit@localhost.localdomain
Link: http://lkml.kernel.org/r/1536927045-23536-3-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prefer _THIS_IP_ defined in linux/kernel.h.
Most definitions of current_text_addr were the same as _THIS_IP_, but
a few archs had inline assembly instead.
This patch removes the final call site of current_text_addr, making all
of the definitions dead code.
[akpm@linux-foundation.org: fix arch/csky/include/asm/processor.h]
Link: http://lkml.kernel.org/r/20180911182413.180715-1-ndesaulniers@google.com
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building with clang (8 trunk, 7.0 release) the frame size limit is
hit:
arch/powerpc/xmon/xmon.c:452:12: warning: stack frame size of 2576
bytes in function 'xmon_core' [-Wframe-larger-than=]
Some investigation by Naveen indicates this is due to clang saving the
addresses to printf format strings on the stack.
While this issue is investigated, bump up the frame size limit for xmon
when building with clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/252
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
