Currently, the HPT code in HV KVM maintains a dirty bit per guest page
in the rmap array, whether or not dirty page tracking has been enabled
for the memory slot. In contrast, the radix code maintains a dirty
bit per guest page in memslot->dirty_bitmap, and only does so when
dirty page tracking has been enabled.
This changes the HPT code to maintain the dirty bits in the memslot
dirty_bitmap like radix does. This results in slightly less code
overall, and will mean that we do not lose the dirty bits when
transitioning between HPT and radix mode in future.
There is one minor change to behaviour as a result. With HPT, when
dirty tracking was enabled for a memslot, we would previously clear
all the dirty bits at that point (both in the HPT entries and in the
rmap arrays), meaning that a KVM_GET_DIRTY_LOG ioctl immediately
following would show no pages as dirty (assuming no vcpus have run
in the meantime). With this change, the dirty bits on HPT entries
are not cleared at the point where dirty tracking is enabled, so
KVM_GET_DIRTY_LOG would show as dirty any guest pages that are
resident in the HPT and dirty. This is consistent with what happens
on radix.
This also fixes a bug in the mark_pages_dirty() function for radix
(in the sense that the function no longer exists). In the case where
a large page of 64 normal pages or more is marked dirty, the
addressing of the dirty bitmap was incorrect and could write past
the end of the bitmap. Fortunately this case was never hit in
practice because a 2MB large page is only 32 x 64kB pages, and we
don't support backing the guest with 1GB huge pages at this point.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This renames the kvm->arch.hpte_setup_done field to mmu_ready because
we will want to use it for radix guests too -- both for setting things
up before vcpu execution, and for excluding vcpus from executing while
MMU-related things get changed, such as in future switching the MMU
from radix to HPT mode or vice-versa.
This also moves the call to kvmppc_setup_partition_table() that was
done in kvmppc_hv_setup_htab_rma() for HPT guests, and the setting
of mmu_ready, into the caller in kvmppc_vcpu_run_hv().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This removes the dependence of KVM on the mmu_psize_defs array (which
stores information about hardware support for various page sizes) and
the things derived from it, chiefly hpte_page_sizes[], hpte_page_size(),
hpte_actual_page_size() and get_sllp_encoding(). We also no longer
rely on the mmu_slb_size variable or the MMU_FTR_1T_SEGMENTS feature
bit.
The reason for doing this is so we can support a HPT guest on a radix
host. In a radix host, the mmu_psize_defs array contains information
about page sizes supported by the MMU in radix mode rather than the
page sizes supported by the MMU in HPT mode. Similarly, mmu_slb_size
and the MMU_FTR_1T_SEGMENTS bit are not set.
Instead we hard-code knowledge of the behaviour of the HPT MMU in the
POWER7, POWER8 and POWER9 processors (which are the only processors
supported by HV KVM) - specifically the encoding of the LP fields in
the HPT and SLB entries, and the fact that they have 32 SLB entries
and support 1TB segments.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch of the powerpc tree to get the
commit that reverts the patch "KVM: PPC: Book3S HV: POWER9 does not
require secondary thread management". This is needed for subsequent
patches which will be applied on this branch.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This reverts commit 94a04bc25a.
In order to run HPT guests on a radix POWER9 host, we will have to run
the host in single-threaded mode, because POWER9 processors do not
currently support running some threads of a core in HPT mode while
others are in radix mode ("mixed mode").
That means that we will need the same mechanisms that are used on
POWER8 to make the secondary threads available to KVM, which were
disabled on POWER9 by commit 94a04bc25a.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Particularly because kvmppc_fast_vcpu_kick_hv() is a callback,
ensure that we properly serialize wq active checks in order to
avoid potentially missing a wakeup due to racing with the waiter
side.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 468808bd35 ("KVM: PPC: Book3S HV: Set process table for HPT
guests on POWER9", 2017-01-30) added a call to kvmppc_update_lpcr()
which doesn't hold the kvm->lock mutex around the call, as required.
This adds the lock/unlock pair, and for good measure, includes
the kvmppc_setup_partition_table() call in the locked region, since
it is altering global state of the VM.
This error appears not to have any fatal consequences for the host;
the consequences would be that the VCPUs could end up running with
different LPCR values, or an update to the LPCR value by userspace
using the one_reg interface could get overwritten, or the update
done by kvmhv_configure_mmu() could get overwritten.
Cc: stable@vger.kernel.org # v4.10+
Fixes: 468808bd35 ("KVM: PPC: Book3S HV: Set process table for HPT guests on POWER9")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the 'ppc-kvm' topic branch from the powerpc tree in
order to bring in some fixes which touch both powerpc and KVM code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds information about storage keys to the struct returned by
the KVM_PPC_GET_SMMU_INFO ioctl. The new fields replace a pad field,
which was zeroed by previous kernel versions. Thus userspace that
knows about the new fields will see zeroes when running on an older
kernel, indicating that storage keys are not supported. The size of
the structure has not changed.
The number of keys is hard-coded for the CPUs supported by HV KVM,
which is just POWER7, POWER8 and POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
KVM currently validates the size of the VPA registered by the client
against sizeof(struct lppaca), however we align (and therefore size)
that struct to 1kB to avoid crossing a 4kB boundary in the client.
PAPR calls for sizes >= 640 bytes to be accepted. Hard code this with
a comment.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 CPUs have independent MMU contexts per thread, so KVM does not
need to quiesce secondary threads, so the hwthread_req/hwthread_state
protocol does not have to be used. So patch it away on POWER9, and patch
away the branch from the Linux idle wakeup to kvm_start_guest that is
never used.
Add a warning and error out of kvmppc_grab_hwthread in case it is ever
called on POWER9.
This avoids a hwsync in the idle wakeup path on POWER9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
[mpe: Use WARN(...) instead of WARN_ON()/pr_err(...)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements
There is a small conflict in arch/s390 due to an arch-wide field rename.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZW4XTAAoJEL/70l94x66DkhMH/izpk54KI17PtyQ9VYI2sYeZ
BWK6Kl886g3ij4pFi3pECqjDJzWaa3ai+vFfzzpJJ8OkCJT5Rv4LxC5ERltVVmR8
A3T1I/MRktSC0VJLv34daPC2z4Lco/6SPipUpPnL4bE2HATKed4vzoOjQ3tOeGTy
dwi7TFjKwoVDiM7kPPDRnTHqCe5G5n13sZ49dBe9WeJ7ttJauWqoxhlYosCGNPEj
g8ZX8+cvcAhVnz5uFL8roqZ8ygNEQq2mgkU18W8ZZKuiuwR0gdsG0gSBFNTdwIMK
NoreRKMrw0+oLXTIB8SZsoieU6Qi7w3xMAMabe8AJsvYtoersugbOmdxGCr1lsA=
=OD7H
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"PPC:
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
Update my email address
kvm: vmx: allow host to access guest MSR_IA32_BNDCFGS
x86: kvm: mmu: use ept a/d in vmcs02 iff used in vmcs12
kvm: x86: mmu: allow A/D bits to be disabled in an mmu
x86: kvm: mmu: make spte mmio mask more explicit
x86: kvm: mmu: dead code thanks to access tracking
KVM: PPC: Book3S: Fix typo in XICS-on-XIVE state saving code
KVM: PPC: Book3S HV: Close race with testing for signals on guest entry
KVM: PPC: Book3S HV: Simplify dynamic micro-threading code
KVM: x86: remove ignored type attribute
KVM: LAPIC: Fix lapic timer injection delay
KVM: lapic: reorganize restart_apic_timer
KVM: lapic: reorganize start_hv_timer
kvm: nVMX: Check memory operand to INVVPID
KVM: s390: Inject machine check into the nested guest
KVM: s390: Inject machine check into the guest
tools/kvm_stat: add new interactive command 'b'
tools/kvm_stat: add new command line switch '-i'
tools/kvm_stat: fix error on interactive command 'g'
KVM: SVM: suppress unnecessary NMI singlestep on GIF=0 and nested exit
...
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
At present, interrupts are hard-disabled fairly late in the guest
entry path, in the assembly code. Since we check for pending signals
for the vCPU(s) task(s) earlier in the guest entry path, it is
possible for a signal to be delivered before we enter the guest but
not be noticed until after we exit the guest for some other reason.
Similarly, it is possible for the scheduler to request a reschedule
while we are in the guest entry path, and we won't notice until after
we have run the guest, potentially for a whole timeslice.
Furthermore, with a radix guest on POWER9, we can take the interrupt
with the MMU on. In this case we end up leaving interrupts
hard-disabled after the guest exit, and they are likely to stay
hard-disabled until we exit to userspace or context-switch to
another process. This was masking the fact that we were also not
setting the RI (recoverable interrupt) bit in the MSR, meaning
that if we had taken an interrupt, it would have crashed the host
kernel with an unrecoverable interrupt message.
To close these races, we need to check for signals and reschedule
requests after hard-disabling interrupts, and then keep interrupts
hard-disabled until we enter the guest. If there is a signal or a
reschedule request from another CPU, it will send an IPI, which will
cause a guest exit.
This puts the interrupt disabling before we call kvmppc_start_thread()
for all the secondary threads of this core that are going to run vCPUs.
The reason for that is that once we have started the secondary threads
there is no easy way to back out without going through at least part
of the guest entry path. However, kvmppc_start_thread() includes some
code for radix guests which needs to call smp_call_function(), which
must be called with interrupts enabled. To solve this problem, this
patch moves that code into a separate function that is called earlier.
When the guest exit is caused by an external interrupt, a hypervisor
doorbell or a hypervisor maintenance interrupt, we now handle these
using the replay facility. __kvmppc_vcore_entry() now returns the
trap number that caused the exit on this thread, and instead of the
assembly code jumping to the handler entry, we return to C code with
interrupts still hard-disabled and set the irq_happened flag in the
PACA, so that when we do local_irq_enable() the appropriate handler
gets called.
With all this, we now have the interrupt soft-enable flag clear while
we are in the guest. This is useful because code in the real-mode
hypercall handlers that checks whether interrupts are enabled will
now see that they are disabled, which is correct, since interrupts
are hard-disabled in the real-mode code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since commit b009031f74 ("KVM: PPC: Book3S HV: Take out virtual
core piggybacking code", 2016-09-15), we only have at most one
vcore per subcore. Previously, the fact that there might be more
than one vcore per subcore meant that we had the notion of a
"master vcore", which was the vcore that controlled thread 0 of
the subcore. We also needed a list per subcore in the core_info
struct to record which vcores belonged to each subcore. Now that
there can only be one vcore in the subcore, we can replace the
list with a simple pointer and get rid of the notion of the
master vcore (and in fact treat every vcore as a master vcore).
We can also get rid of the subcore_vm[] field in the core_info
struct since it is never read.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Enhance KVM to cause a guest exit with KVM_EXIT_NMI
exit reason upon a machine check exception (MCE) in
the guest address space if the KVM_CAP_PPC_FWNMI
capability is enabled (instead of delivering a 0x200
interrupt to guest). This enables QEMU to build error
log and deliver machine check exception to guest via
guest registered machine check handler.
This approach simplifies the delivery of machine
check exception to guest OS compared to the earlier
approach of KVM directly invoking 0x200 guest interrupt
vector.
This design/approach is based on the feedback for the
QEMU patches to handle machine check exception. Details
of earlier approach of handling machine check exception
in QEMU and related discussions can be found at:
https://lists.nongnu.org/archive/html/qemu-devel/2014-11/msg00813.html
Note:
This patch now directly invokes machine_check_print_event_info()
from kvmppc_handle_exit_hv() to print the event to host console
at the time of guest exit before the exception is passed on to the
guest. Hence, the host-side handling which was performed earlier
via machine_check_fwnmi is removed.
The reasons for this approach is (i) it is not possible
to distinguish whether the exception occurred in the
guest or the host from the pt_regs passed on the
machine_check_exception(). Hence machine_check_exception()
calls panic, instead of passing on the exception to
the guest, if the machine check exception is not
recoverable. (ii) the approach introduced in this
patch gives opportunity to the host kernel to perform
actions in virtual mode before passing on the exception
to the guest. This approach does not require complex
tweaks to machine_check_fwnmi and friends.
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On a POWER9 system, it is possible for an interrupt to become pending
for a VCPU when that VCPU is about to cede (execute a H_CEDE hypercall)
and has already disabled interrupts, or in the H_CEDE processing up
to the point where the XIVE context is pulled from the hardware. In
such a case, the H_CEDE should not sleep, but should return immediately
to the guest. However, the conditions tested in kvmppc_vcpu_woken()
don't include the condition that a XIVE interrupt is pending, so the
VCPU could sleep until the next decrementer interrupt.
To fix this, we add a new xive_interrupt_pending() helper which looks
in the XIVE context that was pulled from the hardware to see if the
priority of any pending interrupt is higher (numerically lower than)
the CPU priority. If so then kvmppc_vcpu_woken() will return true.
If the XIVE context has never been used, then both the pipr and the
cppr fields will be zero and the test will indicate that no interrupt
is pending.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On POWER9, we no longer have the restriction that we had on POWER8
where all threads in a core have to be in the same partition, so
the CPU threads are now independent. However, we still want to be
able to run guests with a virtual SMT topology, if only to allow
migration of guests from POWER8 systems to POWER9.
A guest that has a virtual SMT mode greater than 1 will expect to
be able to use the doorbell facility; it will expect the msgsndp
and msgclrp instructions to work appropriately and to be able to read
sensible values from the TIR (thread identification register) and
DPDES (directed privileged doorbell exception status) special-purpose
registers. However, since each CPU thread is a separate sub-processor
in POWER9, these instructions and registers can only be used within
a single CPU thread.
In order for these instructions to appear to act correctly according
to the guest's virtual SMT mode, we have to trap and emulate them.
We cause them to trap by clearing the HFSCR_MSGP bit in the HFSCR
register. The emulation is triggered by the hypervisor facility
unavailable interrupt that occurs when the guest uses them.
To cause a doorbell interrupt to occur within the guest, we set the
DPDES register to 1. If the guest has interrupts enabled, the CPU
will generate a doorbell interrupt and clear the DPDES register in
hardware. The DPDES hardware register for the guest is saved in the
vcpu->arch.vcore->dpdes field. Since this gets written by the guest
exit code, other VCPUs wishing to cause a doorbell interrupt don't
write that field directly, but instead set a vcpu->arch.doorbell_request
flag. This is consumed and set to 0 by the guest entry code, which
then sets DPDES to 1.
Emulating reads of the DPDES register is somewhat involved, because
it requires reading the doorbell pending interrupt status of all of the
VCPU threads in the virtual core, and if any of those VCPUs are
running, their doorbell status is only up-to-date in the hardware
DPDES registers of the CPUs where they are running. In order to get
a reasonable approximation of the current doorbell status, we send
those CPUs an IPI, causing an exit from the guest which will update
the vcpu->arch.vcore->dpdes field. We then use that value in
constructing the emulated DPDES register value.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This allows userspace to set the desired virtual SMT (simultaneous
multithreading) mode for a VM, that is, the number of VCPUs that
get assigned to each virtual core. Previously, the virtual SMT mode
was fixed to the number of threads per subcore, and if userspace
wanted to have fewer vcpus per vcore, then it would achieve that by
using a sparse CPU numbering. This had the disadvantage that the
vcpu numbers can get quite large, particularly for SMT1 guests on
a POWER8 with 8 threads per core. With this patch, userspace can
set its desired virtual SMT mode and then use contiguous vcpu
numbering.
On POWER8, where the threading mode is "strict", the virtual SMT mode
must be less than or equal to the number of threads per subcore. On
POWER9, which implements a "loose" threading mode, the virtual SMT
mode can be any power of 2 between 1 and 8, even though there is
effectively one thread per subcore, since the threads are independent
and can all be in different partitions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to allow us to use a different value for the HFSCR
(Hypervisor Facilities Status and Control Register) when running the
guest from that which applies in the host. The reason for doing this
is to allow us to trap the msgsndp instruction and related operations
in future so that they can be virtualized. We also save the value of
HFSCR when a hypervisor facility unavailable interrupt occurs, because
the high byte of HFSCR indicates which facility the guest attempted to
access.
We save and restore the host value on guest entry/exit because some
bits of it affect host userspace execution.
We only do all this on POWER9, not on POWER8, because we are not
intending to virtualize any of the facilities controlled by HFSCR on
POWER8. In particular, the HFSCR bit that controls execution of
msgsndp and related operations does not exist on POWER8. The HFSCR
doesn't exist at all on POWER7.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
It is possible, through a narrow race condition, for a VCPU to exit
the guest with a H_CEDE hypercall while it has a doorbell interrupt
pending. In this case, the H_CEDE should return immediately, but in
fact it puts the VCPU to sleep until some other interrupt becomes
pending or a prod is received (via another VCPU doing H_PROD).
This fixes it by checking the DPDES (Directed Privileged Doorbell
Exception Status) bit for the thread along with the other interrupt
pending bits.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This allows userspace (e.g. QEMU) to enable large decrementer mode for
the guest when running on a POWER9 host, by setting the LPCR_LD bit in
the guest LPCR value. With this, the guest exit code saves 64 bits of
the guest DEC value on exit. Other places that use the guest DEC
value check the LPCR_LD bit in the guest LPCR value, and if it is set,
omit the 32-bit sign extension that would otherwise be done.
This doesn't change the DEC emulation used by PR KVM because PR KVM
is not supported on POWER9 yet.
This is partly based on an earlier patch by Oliver O'Halloran.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 DD1 has an erratum where writing to the TBU40 register, which
is used to apply an offset to the timebase, can cause the timebase to
lose counts. This results in the timebase on some CPUs getting out of
sync with other CPUs, which then results in misbehaviour of the
timekeeping code.
To work around the problem, we make KVM ignore the timebase offset for
all guests on POWER9 DD1 machines. This means that live migration
cannot be supported on POWER9 DD1 machines.
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
If userspace attempts to call the KVM_RUN ioctl when it has hardware
transactional memory (HTM) enabled, the values that it has put in the
HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by
guest values. To fix this, we detect this condition and save those
SPR values in the thread struct, and disable HTM for the task. If
userspace goes to access those SPRs or the HTM facility in future,
a TM-unavailable interrupt will occur and the handler will reload
those SPRs and re-enable HTM.
If userspace has started a transaction and suspended it, we would
currently lose the transactional state in the guest entry path and
would almost certainly get a "TM Bad Thing" interrupt, which would
cause the host to crash. To avoid this, we detect this case and
return from the KVM_RUN ioctl with an EINVAL error, with the KVM
exit reason set to KVM_EXIT_FAIL_ENTRY.
Fixes: b005255e12 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This restores several special-purpose registers (SPRs) to sane values
on guest exit that were missed before.
TAR and VRSAVE are readable and writable by userspace, and we need to
save and restore them to prevent the guest from potentially affecting
userspace execution (not that TAR or VRSAVE are used by any known
program that run uses the KVM_RUN ioctl). We save/restore these
in kvmppc_vcpu_run_hv() rather than on every guest entry/exit.
FSCR affects userspace execution in that it can prohibit access to
certain facilities by userspace. We restore it to the normal value
for the task on exit from the KVM_RUN ioctl.
IAMR is normally 0, and is restored to 0 on guest exit. However,
with a radix host on POWER9, it is set to a value that prevents the
kernel from executing user-accessible memory. On POWER9, we save
IAMR on guest entry and restore it on guest exit to the saved value
rather than 0. On POWER8 we continue to set it to 0 on guest exit.
PSPB is normally 0. We restore it to 0 on guest exit to prevent
userspace taking advantage of the guest having set it non-zero
(which would allow userspace to set its SMT priority to high).
UAMOR is normally 0. We restore it to 0 on guest exit to prevent
the AMR from being used as a covert channel between userspace
processes, since the AMR is not context-switched at present.
Fixes: b005255e12 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to save the values of three SPRs (special-purpose
registers) used by userspace to control event-based branches (EBBs),
which are essentially interrupts that get delivered directly to
userspace. These registers are loaded up with guest values when
entering the guest, and their values are saved when exiting the
guest, but we were not saving the host values and restoring them
before going back to userspace.
On POWER8 this would only affect userspace programs which explicitly
request the use of EBBs and also use the KVM_RUN ioctl, since the
only source of EBBs on POWER8 is the PMU, and there is an explicit
enable bit in the PMU registers (and those PMU registers do get
properly context-switched between host and guest). On POWER9 there
is provision for externally-generated EBBs, and these are not subject
to the control in the PMU registers.
Since these registers only affect userspace, we can save them when
we first come in from userspace and restore them before returning to
userspace, rather than saving/restoring the host values on every
guest entry/exit. Similarly, we don't need to worry about their
values on offline secondary threads since they execute in the context
of the idle task, which never executes in userspace.
Fixes: b005255e12 ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08)
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
kvmppc_alloc_host_rm_ops() holds get_online_cpus() while invoking
cpuhp_setup_state_nocalls().
cpuhp_setup_state_nocalls() invokes get_online_cpus() as well. This is
correct, but prevents the conversion of the hotplug locking to a percpu
rwsem.
Use cpuhp_setup_state_nocalls_cpuslocked() to avoid the nested
call. Convert *_online_cpus() to the new interfaces while at it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: kvm@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: kvm-ppc@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Alexander Graf <agraf@suse.com>
Link: http://lkml.kernel.org/r/20170524081547.809616236@linutronix.de
This merges in the powerpc topic/xive branch to bring in the code for
the in-kernel XICS interrupt controller emulation to use the new XIVE
(eXternal Interrupt Virtualization Engine) hardware in the POWER9 chip
directly, rather than via a XICS emulation in firmware.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With CONFIG_DEBUG_PREEMPT, get_paca() produces the following warning
in kvmppc_book3s_init_hv() since it calls debug_smp_processor_id().
There is no real issue with the xics_phys field.
If paca->kvm_hstate.xics_phys is non-zero on one cpu, it will be
non-zero on them all. Therefore this is not fixing any actual
problem, just the warning.
[ 138.521188] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/5596
[ 138.521308] caller is .kvmppc_book3s_init_hv+0x184/0x350 [kvm_hv]
[ 138.521404] CPU: 5 PID: 5596 Comm: modprobe Not tainted 4.11.0-rc3-00022-gc7e790c #1
[ 138.521509] Call Trace:
[ 138.521563] [c0000007d018b810] [c0000000023eef10] .dump_stack+0xe4/0x150 (unreliable)
[ 138.521694] [c0000007d018b8a0] [c000000001f6ec04] .check_preemption_disabled+0x134/0x150
[ 138.521829] [c0000007d018b940] [d00000000a010274] .kvmppc_book3s_init_hv+0x184/0x350 [kvm_hv]
[ 138.521963] [c0000007d018ba00] [c00000000191d5cc] .do_one_initcall+0x5c/0x1c0
[ 138.522082] [c0000007d018bad0] [c0000000023e9494] .do_init_module+0x84/0x240
[ 138.522201] [c0000007d018bb70] [c000000001aade18] .load_module+0x1f68/0x2a10
[ 138.522319] [c0000007d018bd20] [c000000001aaeb30] .SyS_finit_module+0xc0/0xf0
[ 138.522439] [c0000007d018be30] [c00000000191baec] system_call+0x38/0xfc
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.
This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
We traditionally have linux/ before asm/
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are going to split <linux/sched/stat.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/stat.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds a not yet working outline of the HPT resizing PAPR
extension. Specifically it adds the necessary ioctl() functions,
their basic steps, the work function which will handle preparation for
the resize, and synchronization between these, the guest page fault
path and guest HPT update path.
The actual guts of the implementation isn't here yet, so for now the
calls will always fail.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The KVM_PPC_ALLOCATE_HTAB ioctl() is used to set the size of hashed page
table (HPT) that userspace expects a guest VM to have, and is also used to
clear that HPT when necessary (e.g. guest reboot).
At present, once the ioctl() is called for the first time, the HPT size can
never be changed thereafter - it will be cleared but always sized as from
the first call.
With upcoming HPT resize implementation, we're going to need to allow
userspace to resize the HPT at reset (to change it back to the default size
if the guest changed it).
So, we need to allow this ioctl() to change the HPT size.
This patch also updates Documentation/virtual/kvm/api.txt to reflect
the new behaviour. In fact the documentation was already slightly
incorrect since 572abd5 "KVM: PPC: Book3S HV: Don't fall back to
smaller HPT size in allocation ioctl"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, kvmppc_alloc_hpt() both allocates a new hashed page table (HPT)
and sets it up as the active page table for a VM. For the upcoming HPT
resize implementation we're going to want to allocate HPTs separately from
activating them.
So, split the allocation itself out into kvmppc_allocate_hpt() and perform
the activation with a new kvmppc_set_hpt() function. Likewise we split
kvmppc_free_hpt(), which just frees the HPT, from kvmppc_release_hpt()
which unsets it as an active HPT, then frees it.
We also move the logic to fall back to smaller HPT sizes if the first try
fails into the single caller which used that behaviour,
kvmppc_hv_setup_htab_rma(). This introduces a slight semantic change, in
that previously if the initial attempt at CMA allocation failed, we would
fall back to attempting smaller sizes with the page allocator. Now, we
try first CMA, then the page allocator at each size. As far as I can tell
this change should be harmless.
To match, we make kvmppc_free_hpt() just free the actual HPT itself. The
call to kvmppc_free_lpid() that was there, we move to the single caller.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, the powerpc kvm_arch structure contains a number of variables
tracking the state of the guest's hashed page table (HPT) in KVM HV. This
patch gathers them all together into a single kvm_hpt_info substructure.
This makes life more convenient for the upcoming HPT resizing
implementation.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the POWER9 radix MMU host and guest support, which
was put into a topic branch because it touches both powerpc and
KVM code.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds a few last pieces of the support for radix guests:
* Implement the backends for the KVM_PPC_CONFIGURE_V3_MMU and
KVM_PPC_GET_RMMU_INFO ioctls for radix guests
* On POWER9, allow secondary threads to be on/off-lined while guests
are running.
* Set up LPCR and the partition table entry for radix guests.
* Don't allocate the rmap array in the kvm_memory_slot structure
on radix.
* Don't try to initialize the HPT for radix guests, since they don't
have an HPT.
* Take out the code that prevents the HV KVM module from
initializing on radix hosts.
At this stage, we only support radix guests if the host is running
in radix mode, and only support HPT guests if the host is running in
HPT mode. Thus a guest cannot switch from one mode to the other,
which enables some simplifications.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With radix, the guest can do TLB invalidations itself using the tlbie
(global) and tlbiel (local) TLB invalidation instructions. Linux guests
use local TLB invalidations for translations that have only ever been
accessed on one vcpu. However, that doesn't mean that the translations
have only been accessed on one physical cpu (pcpu) since vcpus can move
around from one pcpu to another. Thus a tlbiel might leave behind stale
TLB entries on a pcpu where the vcpu previously ran, and if that task
then moves back to that previous pcpu, it could see those stale TLB
entries and thus access memory incorrectly. The usual symptom of this
is random segfaults in userspace programs in the guest.
To cope with this, we detect when a vcpu is about to start executing on
a thread in a core that is a different core from the last time it
executed. If that is the case, then we mark the core as needing a
TLB flush and then send an interrupt to any thread in the core that is
currently running a vcpu from the same guest. This will get those vcpus
out of the guest, and the first one to re-enter the guest will do the
TLB flush. The reason for interrupting the vcpus executing on the old
core is to cope with the following scenario:
CPU 0 CPU 1 CPU 4
(core 0) (core 0) (core 1)
VCPU 0 runs task X VCPU 1 runs
core 0 TLB gets
entries from task X
VCPU 0 moves to CPU 4
VCPU 0 runs task X
Unmap pages of task X
tlbiel
(still VCPU 1) task X moves to VCPU 1
task X runs
task X sees stale TLB
entries
That is, as soon as the VCPU starts executing on the new core, it
could unmap and tlbiel some page table entries, and then the task
could migrate to one of the VCPUs running on the old core and
potentially see stale TLB entries.
Since the TLB is shared between all the threads in a core, we only
use the bit of kvm->arch.need_tlb_flush corresponding to the first
thread in the core. To ensure that we don't have a window where we
can miss a flush, this moves the clearing of the bit from before the
actual flush to after it. This way, two threads might both do the
flush, but we prevent the situation where one thread can enter the
guest before the flush is finished.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds code to keep track of dirty pages when requested (that is,
when memslot->dirty_bitmap is non-NULL) for radix guests. We use the
dirty bits in the PTEs in the second-level (partition-scoped) page
tables, together with a bitmap of pages that were dirty when their
PTE was invalidated (e.g., when the page was paged out). This bitmap
is stored in the first half of the memslot->dirty_bitmap area, and
kvm_vm_ioctl_get_dirty_log_hv() now uses the second half for the
bitmap that gets returned to userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds the code to construct the second-level ("partition-scoped" in
architecturese) page tables for guests using the radix MMU. Apart from
the PGD level, which is allocated when the guest is created, the rest
of the tree is all constructed in response to hypervisor page faults.
As well as hypervisor page faults for missing pages, we also get faults
for reference/change (RC) bits needing to be set, as well as various
other error conditions. For now, we only set the R or C bit in the
guest page table if the same bit is set in the host PTE for the
backing page.
This code can take advantage of the guest being backed with either
transparent or ordinary 2MB huge pages, and insert 2MB page entries
into the guest page tables. There is no support for 1GB huge pages
yet.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds the implementation of the KVM_PPC_CONFIGURE_V3_MMU ioctl
for HPT guests on POWER9. With this, we can return 1 for the
KVM_CAP_PPC_MMU_HASH_V3 capability.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds two capabilities and two ioctls to allow userspace to
find out about and configure the POWER9 MMU in a guest. The two
capabilities tell userspace whether KVM can support a guest using
the radix MMU, or using the hashed page table (HPT) MMU with a
process table and segment tables. (Note that the MMUs in the
POWER9 processor cores do not use the process and segment tables
when in HPT mode, but the nest MMU does).
The KVM_PPC_CONFIGURE_V3_MMU ioctl allows userspace to specify
whether a guest will use the radix MMU or the HPT MMU, and to
specify the size and location (in guest space) of the process
table.
The KVM_PPC_GET_RMMU_INFO ioctl gives userspace information about
the radix MMU. It returns a list of supported radix tree geometries
(base page size and number of bits indexed at each level of the
radix tree) and the encoding used to specify the various page
sizes for the TLB invalidate entry instruction.
Initially, both capabilities return 0 and the ioctls return -EINVAL,
until the necessary infrastructure for them to operate correctly
is added.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The H_PROD hypercall is supposed to wake up an idle vcpu. We have
an implementation, but because Linux doesn't use it except when
doing cpu hotplug, it was never tested properly. AIX does use it,
and reported it broken. It turns out we were waking the wrong
vcpu (the one doing H_PROD, not the target of the prod) and we
weren't handling the case where the target needs an IPI to wake
it. Fix it by using the existing kvmppc_fast_vcpu_kick_hv()
function, which is intended for this kind of thing, and by using
the target vcpu not the current vcpu.
We were also not looking at the prodded flag when checking whether a
ceded vcpu should wake up, so this adds checks for the prodded flag
alongside the checks for pending exceptions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
If the target vcpu for kvmppc_fast_vcpu_kick_hv() is not running on
any CPU, then we will have vcpu->arch.thread_cpu == -1, and as it
happens, kvmppc_fast_vcpu_kick_hv will call kvmppc_ipi_thread with
-1 as the cpu argument. Although this is not meaningful, in the past,
before commit 1704a81cce ("KVM: PPC: Book3S HV: Use msgsnd for IPIs
to other cores on POWER9", 2016-11-18), it was harmless because CPU
-1 is not in the same core as any real CPU thread. On a POWER9,
however, we don't do the "same core" check, so we were trying to
do a msgsnd to thread -1, which is invalid. To avoid this, we add
a check to see that vcpu->arch.thread_cpu is >= 0 before calling
kvmppc_ipi_thread() with it. Since vcpu->arch.thread_vcpu can change
asynchronously, we use READ_ONCE to ensure that the value we check is
the same value that we use as the argument to kvmppc_ipi_thread().
Fixes: 1704a81cce ("KVM: PPC: Book3S HV: Use msgsnd for IPIs to other cores on POWER9")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86: userspace can now hide nested VMX features from guests; nested
VMX can now run Hyper-V in a guest; support for AVX512_4VNNIW and
AVX512_FMAPS in KVM; infrastructure support for virtual Intel GPUs.
PPC: support for KVM guests on POWER9; improved support for interrupt
polling; optimizations and cleanups.
s390: two small optimizations, more stuff is in flight and will be
in 4.11.
ARM: support for the GICv3 ITS on 32bit platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYTkP0FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
lZIH/iT1n9OQXcuTpYYnQhuCenzI3GZZOIMTbCvK2i5bo0FIJKxVn0EiAAqZSXvO
nO185FqjOgLuJ1AD1kJuxzye5suuQp4HIPWWgNHcexLuy43WXWKZe0IQlJ4zM2Xf
u31HakpFmVDD+Cd1qN3yDXtDrRQ79/xQn2kw7CWb8olp+pVqwbceN3IVie9QYU+3
gCz0qU6As0aQIwq2PyalOe03sO10PZlm4XhsoXgWPG7P18BMRhNLTDqhLhu7A/ry
qElVMANT7LSNLzlwNdpzdK8rVuKxETwjlc1UP8vSuhrwad4zM2JJ1Exk26nC2NaG
D0j4tRSyGFIdx6lukZm7HmiSHZ0=
=mkoB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.
x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.
PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.
s390:
- two small optimizations, more stuff is in flight and will be in
4.11.
ARM:
- support for the GICv3 ITS on 32bit platforms"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...
Install the callbacks via the state machine.
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: kvm-ppc@vger.kernel.org
Cc: Paul Mackerras <paulus@samba.org>
Cc: rt@linutronix.de
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.com>
Link: http://lkml.kernel.org/r/20161126231350.10321-18-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix comment block to match kernel comment style.
Fix print format from signed to unsigned.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The kvm module parameter halt_poll_ns defines the global maximum halt
polling interval and can be dynamically changed by writing to the
/sys/module/kvm/parameters/halt_poll_ns sysfs file. However in kvm-hv
this module parameter value is only ever checked when we grow the current
polling interval for the given vcore. This means that if we decrease the
halt_poll_ns value below the current polling interval we won't see any
effect unless we try to grow the polling interval above the new max at some
point or it happens to be shrunk below the halt_poll_ns value.
Update the halt polling code so that we always check for a new module param
value of halt_poll_ns and set the current halt polling interval to it if
it's currently greater than the new max. This means that it's redundant to
also perform this check in the grow_halt_poll_ns() function now.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The previous patch exported the variables which back the module parameters
of the generic kvm module. Now use these variables in the kvm-hv module
so that any change to the generic module parameters will also have the
same effect for the kvm-hv module. This removes the duplication of the
kvm module parameters which was redundant and should reduce confusion when
tuning them.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The function kvmppc_set_arch_compat() is used to determine the value of the
processor compatibility register (PCR) for a guest running in a given
compatibility mode. There is currently no support for v3.00 of the ISA.
Add support for v3.00 of the ISA which adds an ISA v2.07 compatilibity mode
to the PCR.
We also add a check to ensure the processor we are running on is capable of
emulating the chosen processor (for example a POWER7 cannot emulate a
POWER8, similarly with a POWER8 and a POWER9).
Based on work by: Paul Mackerras <paulus@ozlabs.org>
[paulus@ozlabs.org - moved dummy PCR_ARCH_300 definition here; set
guest_pcr_bit when arch_compat == 0, added comment.]
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
With POWER9, each CPU thread has its own MMU context and can be
in the host or a guest independently of the other threads; there is
still however a restriction that all threads must use the same type
of address translation, either radix tree or hashed page table (HPT).
Since we only support HPT guests on a HPT host at this point, we
can treat the threads as being independent, and avoid all of the
work of coordinating the CPU threads. To make this simpler, we
introduce a new threads_per_vcore() function that returns 1 on
POWER9 and threads_per_subcore on POWER7/8, and use that instead
of threads_per_subcore or threads_per_core in various places.
This also changes the value of the KVM_CAP_PPC_SMT capability on
POWER9 systems from 4 to 1, so that userspace will not try to
create VMs with multiple vcpus per vcore. (If userspace did create
a VM that thought it was in an SMT mode, the VM might try to use
the msgsndp instruction, which will not work as expected. In
future it may be possible to trap and emulate msgsndp in order to
allow VMs to think they are in an SMT mode, if only for the purpose
of allowing migration from POWER8 systems.)
With all this, we can now run guests on POWER9 as long as the host
is running with HPT translation. Since userspace currently has no
way to request radix tree translation for the guest, the guest has
no choice but to use HPT translation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The new XIVE interrupt controller on POWER9 can direct external
interrupts to the hypervisor or the guest. The interrupts directed to
the hypervisor are controlled by an LPCR bit called LPCR_HVICE, and
come in as a "hypervisor virtualization interrupt". This sets the
LPCR bit so that hypervisor virtualization interrupts can occur while
we are in the guest. We then also need to cope with exiting the guest
because of a hypervisor virtualization interrupt.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 includes a new interrupt controller, called XIVE, which is
quite different from the XICS interrupt controller on POWER7 and
POWER8 machines. KVM-HV accesses the XICS directly in several places
in order to send and clear IPIs and handle interrupts from PCI
devices being passed through to the guest.
In order to make the transition to XIVE easier, OPAL firmware will
include an emulation of XICS on top of XIVE. Access to the emulated
XICS is via OPAL calls. The one complication is that the EOI
(end-of-interrupt) function can now return a value indicating that
another interrupt is pending; in this case, the XIVE will not signal
an interrupt in hardware to the CPU, and software is supposed to
acknowledge the new interrupt without waiting for another interrupt
to be delivered in hardware.
This adapts KVM-HV to use the OPAL calls on machines where there is
no XICS hardware. When there is no XICS, we look for a device-tree
node with "ibm,opal-intc" in its compatible property, which is how
OPAL indicates that it provides XICS emulation.
In order to handle the EOI return value, kvmppc_read_intr() has
become kvmppc_read_one_intr(), with a boolean variable passed by
reference which can be set by the EOI functions to indicate that
another interrupt is pending. The new kvmppc_read_intr() keeps
calling kvmppc_read_one_intr() until there are no more interrupts
to process. The return value from kvmppc_read_intr() is the
largest non-zero value of the returns from kvmppc_read_one_intr().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On POWER9, the msgsnd instruction is able to send interrupts to
other cores, as well as other threads on the local core. Since
msgsnd is generally simpler and faster than sending an IPI via the
XICS, we use msgsnd for all IPIs sent by KVM on POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER9 adds new capabilities to the tlbie (TLB invalidate entry)
and tlbiel (local tlbie) instructions. Both instructions get a
set of new parameters (RIC, PRS and R) which appear as bits in the
instruction word. The tlbiel instruction now has a second register
operand, which contains a PID and/or LPID value if needed, and
should otherwise contain 0.
This adapts KVM-HV's usage of tlbie and tlbiel to work on POWER9
as well as older processors. Since we only handle HPT guests so
far, we need RIC=0 PRS=0 R=0, which ends up with the same instruction
word as on previous processors, so we don't need to conditionally
execute different instructions depending on the processor.
The local flush on first entry to a guest in book3s_hv_rmhandlers.S
is a loop which depends on the number of TLB sets. Rather than
using feature sections to set the number of iterations based on
which CPU we're on, we now work out this number at VM creation time
and store it in the kvm_arch struct. That will make it possible to
get the number from the device tree in future, which will help with
compatibility with future processors.
Since mmu_partition_table_set_entry() does a global flush of the
whole LPID, we don't need to do the TLB flush on first entry to the
guest on each processor. Therefore we don't set all bits in the
tlb_need_flush bitmap on VM startup on POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register). They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.
The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode. We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On POWER9, the SDR1 register (hashed page table base address) is no
longer used, and instead the hardware reads the HPT base address
and size from the partition table. The partition table entry also
contains the bits that specify the page size for the VRMA mapping,
which were previously in the LPCR. The VPM0 bit of the LPCR is
now reserved; the processor now always uses the VRMA (virtual
real-mode area) mechanism for guest real-mode accesses in HPT mode,
and the RMO (real-mode offset) mechanism has been dropped.
When entering or exiting the guest, we now only have to set the
LPIDR (logical partition ID register), not the SDR1 register.
There is also no requirement now to transition via a reserved
LPID value.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e3812150 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This keeps a per vcpu cache for recently page faulted MMIO entries.
On a page fault, if the entry exists in the cache, we can avoid some
time-consuming paths, for example, looking up HPT, locking HPTE twice
and searching mmio gfn from memslots, then directly call
kvmppc_hv_emulate_mmio().
In current implenment, we limit the size of cache to four. We think
it's enough to cover the high-frequency MMIO HPTEs in most case.
For example, considering the case of using virtio device, for virtio
legacy devices, one HPTE could handle notifications from up to
1024 (64K page / 64 byte Port IO register) devices, so one cache entry
is enough; for virtio modern devices, we always need one HPTE to handle
notification for each device because modern device would use a 8M MMIO
register to notify host instead of Port IO register, typically the
system's configuration should not exceed four virtio devices per
vcpu, four cache entry is also enough in this case. Of course, if needed,
we could also modify the macro to a module parameter in the future.
Signed-off-by: Yongji Xie <xyjxie@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Using list_move_tail() instead of list_del() + list_add_tail().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This takes out the code that arranges to run two (or more) virtual
cores on a single subcore when possible, that is, when both vcores
are from the same VM, the VM is configured with one CPU thread per
virtual core, and all the per-subcore registers have the same value
in each vcore. Since the VTB (virtual timebase) is a per-subcore
register, and will almost always differ between vcores, this code
is disabled on POWER8 machines, meaning that it is only usable on
POWER7 machines (which don't have VTB). Given the tiny number of
POWER7 machines which have firmware that allows them to run HV KVM,
the benefit of simplifying the code outweighs the loss of this
feature on POWER7 machines.
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
POWER8 has one virtual timebase (VTB) register per subcore, not one
per CPU thread. The HV KVM code currently treats VTB as a per-thread
register, which can lead to spurious soft lockup messages from guests
which use the VTB as the time source for the soft lockup detector.
(CPUs before POWER8 did not have the VTB register.)
For HV KVM, this fixes the problem by making only the primary thread
in each virtual core save and restore the VTB value. With this,
the VTB state becomes part of the kvmppc_vcore structure. This
also means that "piggybacking" of multiple virtual cores onto one
subcore is not possible on POWER8, because then the virtual cores
would share a single VTB register.
PR KVM emulates a VTB register, which is per-vcpu because PR KVM
has no notion of CPU threads or SMT. For PR KVM we move the VTB
state into the kvmppc_vcpu_book3s struct.
Cc: stable@vger.kernel.org # v3.14+
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When a guest has a PCI pass-through device with an interrupt, it
will direct the interrupt to a particular guest VCPU. In fact the
physical interrupt might arrive on any CPU, and then get
delivered to the target VCPU in the emulated XICS (guest interrupt
controller), and eventually delivered to the target VCPU.
Now that we have code to handle device interrupts in real mode
without exiting to the host kernel, there is an advantage to having
the device interrupt arrive on the same sub(core) as the target
VCPU is running on. In this situation, the interrupt can be
delivered to the target VCPU without any exit to the host kernel
(using a hypervisor doorbell interrupt between threads if
necessary).
This patch aims to get passed-through device interrupts arriving
on the correct core by setting the interrupt server in the real
hardware XICS for the interrupt to the first thread in the (sub)core
where its target VCPU is running. We do this in the real-mode H_EOI
code because the H_EOI handler already needs to look at the
emulated ICS state for the interrupt (whereas the H_XIRR handler
doesn't), and we know we are running in the target VCPU context
at that point.
We set the server CPU in hardware using an OPAL call, regardless of
what the IRQ affinity mask for the interrupt says, and without
updating the affinity mask. This amounts to saying that when an
interrupt is passed through to a guest, as a matter of policy we
allow the guest's affinity for the interrupt to override the host's.
This is inspired by an earlier patch from Suresh Warrier, although
none of this code came from that earlier patch.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Add a module parameter kvm_irq_bypass for kvm_hv.ko to
disable IRQ bypass for passthrough interrupts. The default
value of this tunable is 1 - that is enable the feature.
Since the tunable is used by built-in kernel code, we use
the module_param_cb macro to achieve this.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In existing real mode ICP code, when updating the virtual ICP
state, if there is a required action that cannot be completely
handled in real mode, as for instance, a VCPU needs to be woken
up, flags are set in the ICP to indicate the required action.
This is checked when returning from hypercalls to decide whether
the call needs switch back to the host where the action can be
performed in virtual mode. Note that if h_ipi_redirect is enabled,
real mode code will first try to message a free host CPU to
complete this job instead of returning the host to do it ourselves.
Currently, the real mode PCI passthrough interrupt handling code
checks if any of these flags are set and simply returns to the host.
This is not good enough as the trap value (0x500) is treated as an
external interrupt by the host code. It is only when the trap value
is a hypercall that the host code searches for and acts on unfinished
work by calling kvmppc_xics_rm_complete.
This patch introduces a special trap BOOK3S_INTERRUPT_HV_RM_HARD
which is returned by KVM if there is unfinished business to be
completed in host virtual mode after handling a PCI passthrough
interrupt. The host checks for this special interrupt condition
and calls into the kvmppc_xics_rm_complete, which is made an
exported function for this reason.
[paulus@ozlabs.org - moved logic to set r12 to BOOK3S_INTERRUPT_HV_RM_HARD
in book3s_hv_rmhandlers.S into the end of kvmppc_check_wake_reason.]
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently, KVM switches back to the host to handle any external
interrupt (when the interrupt is received while running in the
guest). This patch updates real-mode KVM to check if an interrupt
is generated by a passthrough adapter that is owned by this guest.
If so, the real mode KVM will directly inject the corresponding
virtual interrupt to the guest VCPU's ICS and also EOI the interrupt
in hardware. In short, the interrupt is handled entirely in real
mode in the guest context without switching back to the host.
In some rare cases, the interrupt cannot be completely handled in
real mode, for instance, a VCPU that is sleeping needs to be woken
up. In this case, KVM simply switches back to the host with trap
reason set to 0x500. This works, but it is clearly not very efficient.
A following patch will distinguish this case and handle it
correctly in the host. Note that we can use the existing
check_too_hard() routine even though we are not in a hypercall to
determine if there is unfinished business that needs to be
completed in host virtual mode.
The patch assumes that the mapping between hardware interrupt IRQ
and virtual IRQ to be injected to the guest already exists for the
PCI passthrough interrupts that need to be handled in real mode.
If the mapping does not exist, KVM falls back to the default
existing behavior.
The KVM real mode code reads mappings from the mapped array in the
passthrough IRQ map without taking any lock. We carefully order the
loads and stores of the fields in the kvmppc_irq_map data structure
using memory barriers to avoid an inconsistent mapping being seen by
the reader. Thus, although it is possible to miss a map entry, it is
not possible to read a stale value.
[paulus@ozlabs.org - get irq_chip from irq_map rather than pimap,
pulled out powernv eoi change into a separate patch, made
kvmppc_read_intr get the vcpu from the paca rather than being
passed in, rewrote the logic at the end of kvmppc_read_intr to
avoid deep indentation, simplified logic in book3s_hv_rmhandlers.S
since we were always restoring SRR0/1 anyway, get rid of the cached
array (just use the mapped array), removed the kick_all_cpus_sync()
call, clear saved_xirr PACA field when we handle the interrupt in
real mode, fix compilation with CONFIG_KVM_XICS=n.]
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Add the irq_bypass_add_producer and irq_bypass_del_producer
functions. These functions get called whenever a GSI is being
defined for a guest. They create/remove the mapping between
host real IRQ numbers and the guest GSI.
Add the following helper functions to manage the
passthrough IRQ map.
kvmppc_set_passthru_irq()
Creates a mapping in the passthrough IRQ map that maps a host
IRQ to a guest GSI. It allocates the structure (one per guest VM)
the first time it is called.
kvmppc_clr_passthru_irq()
Removes the passthrough IRQ map entry given a guest GSI.
The passthrough IRQ map structure is not freed even when the
number of mapped entries goes to zero. It is only freed when
the VM is destroyed.
[paulus@ozlabs.org - modified to use is_pnv_opal_msi() rather than
requiring all passed-through interrupts to use the same irq_chip;
changed deletion so it zeroes out the r_hwirq field rather than
copying the last entry down and decrementing the number of entries.]
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch introduces an IRQ mapping structure, the
kvmppc_passthru_irqmap structure that is to be used
to map the real hardware IRQ in the host with the virtual
hardware IRQ (gsi) that is injected into a guest by KVM for
passthrough adapters.
Currently, we assume a separate IRQ mapping structure for
each guest. Each kvmppc_passthru_irqmap has a mapping arrays,
containing all defined real<->virtual IRQs.
[paulus@ozlabs.org - removed irq_chip field from struct
kvmppc_passthru_irqmap; changed parameter for
kvmppc_get_passthru_irqmap from struct kvm_vcpu * to struct
kvm *, removed small cached array.]
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
vcpu stats are used to collect information about a vcpu which can be viewed
in the debugfs. For example halt_attempted_poll and halt_successful_poll
are used to keep track of the number of times the vcpu attempts to and
successfully polls. These stats are currently not used on powerpc.
Implement incrementation of the halt_attempted_poll and
halt_successful_poll vcpu stats for powerpc. Since these stats are summed
over all the vcpus for all running guests it doesn't matter which vcpu
they are attributed to, thus we choose the current runner vcpu of the
vcore.
Also add new vcpu stats: halt_poll_success_ns, halt_poll_fail_ns and
halt_wait_ns to be used to accumulate the total time spend polling
successfully, polling unsuccessfully and waiting respectively, and
halt_successful_wait to accumulate the number of times the vcpu waits.
Given that halt_poll_success_ns, halt_poll_fail_ns and halt_wait_ns are
expressed in nanoseconds it is necessary to represent these as 64-bit
quantities, otherwise they would overflow after only about 4 seconds.
Given that the total time spend either polling or waiting will be known and
the number of times that each was done, it will be possible to determine
the average poll and wait times. This will give the ability to tune the kvm
module parameters based on the calculated average wait and poll times.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch introduces new halt polling functionality into the kvm_hv kernel
module. When a vcore is idle it will poll for some period of time before
scheduling itself out.
When all of the runnable vcpus on a vcore have ceded (and thus the vcore is
idle) we schedule ourselves out to allow something else to run. In the
event that we need to wake up very quickly (for example an interrupt
arrives), we are required to wait until we get scheduled again.
Implement halt polling so that when a vcore is idle, and before scheduling
ourselves, we poll for vcpus in the runnable_threads list which have
pending exceptions or which leave the ceded state. If we poll successfully
then we can get back into the guest very quickly without ever scheduling
ourselves, otherwise we schedule ourselves out as before.
There exists generic halt_polling code in virt/kvm_main.c, however on
powerpc the polling conditions are different to the generic case. It would
be nice if we could just implement an arch specific kvm_check_block()
function, but there is still other arch specific things which need to be
done for kvm_hv (for example manipulating vcore states) which means that a
separate implementation is the best option.
Testing of this patch with a TCP round robin test between two guests with
virtio network interfaces has found a decrease in round trip time of ~15us
on average. A performance gain is only seen when going out of and
back into the guest often and quickly, otherwise there is no net benefit
from the polling. The polling interval is adjusted such that when we are
often scheduled out for long periods of time it is reduced, and when we
often poll successfully it is increased. The rate at which the polling
interval increases or decreases, and the maximum polling interval, can
be set through module parameters.
Based on the implementation in the generic kvm module by Wanpeng Li and
Paolo Bonzini, and on direction from Paul Mackerras.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The struct kvmppc_vcore is a structure used to store various information
about a virtual core for a kvm guest. The runnable_threads element of the
struct provides a list of all of the currently runnable vcpus on the core
(those in the KVMPPC_VCPU_RUNNABLE state). The previous implementation of
this list was a linked_list. The next patch requires that the list be able
to be iterated over without holding the vcore lock.
Reimplement the runnable_threads list in the kvmppc_vcore struct as an
array. Implement function to iterate over valid entries in the array and
update access sites accordingly.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Use the functions from context_tracking.h directly.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a guest is assigned to a core it converts the host Timebase (TB)
into guest TB by adding guest timebase offset before entering into
guest. During guest exit it restores the guest TB to host TB. This means
under certain conditions (Guest migration) host TB and guest TB can differ.
When we get an HMI for TB related issues the opal HMI handler would
try fixing errors and restore the correct host TB value. With no guest
running, we don't have any issues. But with guest running on the core
we run into TB corruption issues.
If we get an HMI while in the guest, the current HMI handler invokes opal
hmi handler before forcing guest to exit. The guest exit path subtracts
the guest TB offset from the current TB value which may have already
been restored with host value by opal hmi handler. This leads to incorrect
host and guest TB values.
With split-core, things become more complex. With split-core, TB also gets
split and each subcore gets its own TB register. When a hmi handler fixes
a TB error and restores the TB value, it affects all the TB values of
sibling subcores on the same core. On TB errors all the thread in the core
gets HMI. With existing code, the individual threads call opal hmi handle
independently which can easily throw TB out of sync if we have guest
running on subcores. Hence we will need to co-ordinate with all the
threads before making opal hmi handler call followed by TB resync.
This patch introduces a sibling subcore state structure (shared by all
threads in the core) in paca which holds information about whether sibling
subcores are in Guest mode or host mode. An array in_guest[] of size
MAX_SUBCORE_PER_CORE=4 is used to maintain the state of each subcore.
The subcore id is used as index into in_guest[] array. Only primary
thread entering/exiting the guest is responsible to set/unset its
designated array element.
On TB error, we get HMI interrupt on every thread on the core. Upon HMI,
this patch will now force guest to vacate the core/subcore. Primary
thread from each subcore will then turn off its respective bit
from the above bitmap during the guest exit path just after the
guest->host partition switch is complete.
All other threads that have just exited the guest OR were already in host
will wait until all other subcores clears their respective bit.
Once all the subcores turn off their respective bit, all threads will
will make call to opal hmi handler.
It is not necessary that opal hmi handler would resync the TB value for
every HMI interrupts. It would do so only for the HMI caused due to
TB errors. For rest, it would not touch TB value. Hence to make things
simpler, primary thread would call TB resync explicitly once for each
core immediately after opal hmi handler instead of subtracting guest
offset from TB. TB resync call will restore the TB with host value.
Thus we can be sure about the TB state.
One of the primary threads exiting the guest will take up the
responsibility of calling TB resync. It will use one of the top bits
(bit 63) from subcore state flags bitmap to make the decision. The first
primary thread (among the subcores) that is able to set the bit will
have to call the TB resync. Rest all other threads will wait until TB
resync is complete. Once TB resync is complete all threads will then
proceed.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie, Lennart
Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras, Rashmica Gupta,
Russell Currey, Suraj Jitindar Singh, Thiago Jung Bauermann, Valentin
Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell" from Guilherme G. Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme G. Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled from Ian Munsie
- Check periodically the coherent platform function's state from Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes, an erratum
workaround, and a kconfig dependency fix."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YvyQ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Support for Power ISA 3.0 (Power9) Radix Tree MMU from Aneesh Kumar K.V
- Live patching support for ppc64le (also merged via livepatching.git)
Various cleanups & minor fixes from:
- Aaro Koskinen, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V,
Chris Smart, Daniel Axtens, Frederic Barrat, Gavin Shan, Ian Munsie,
Lennart Sorensen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring,
Michael Ellerman, Oliver O'Halloran, Paul Gortmaker, Paul Mackerras,
Rashmica Gupta, Russell Currey, Suraj Jitindar Singh, Thiago Jung
Bauermann, Valentin Rothberg, Vipin K Parashar.
General:
- Update LMB associativity index during DLPAR add/remove from Nathan
Fontenot
- Fix branching to OOL handlers in relocatable kernel from Hari Bathini
- Add support for userspace Power9 copy/paste from Chris Smart
- Always use STRICT_MM_TYPECHECKS from Michael Ellerman
- Add mask of possible MMU features from Michael Ellerman
PCI:
- Enable pass through of NVLink to guests from Alexey Kardashevskiy
- Cleanups in preparation for powernv PCI hotplug from Gavin Shan
- Don't report error in eeh_pe_reset_and_recover() from Gavin Shan
- Restore initial state in eeh_pe_reset_and_recover() from Gavin Shan
- Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
from Guilherme G Piccoli
- Remove the dependency on EEH struct in DDW mechanism from Guilherme
G Piccoli
selftests:
- Test cp_abort during context switch from Chris Smart
- Add several tests for transactional memory support from Rashmica
Gupta
perf:
- Add support for sampling interrupt register state from Anju T
- Add support for unwinding perf-stackdump from Chandan Kumar
cxl:
- Configure the PSL for two CAPI ports on POWER8NVL from Philippe
Bergheaud
- Allow initialization on timebase sync failures from Frederic Barrat
- Increase timeout for detection of AFU mmio hang from Frederic
Barrat
- Handle num_of_processes larger than can fit in the SPA from Ian
Munsie
- Ensure PSL interrupt is configured for contexts with no AFU IRQs
from Ian Munsie
- Add kernel API to allow a context to operate with relocate disabled
from Ian Munsie
- Check periodically the coherent platform function's state from
Christophe Lombard
Freescale:
- Updates from Scott: "Contains 86xx fixes, minor device tree fixes,
an erratum workaround, and a kconfig dependency fix."
* tag 'powerpc-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (192 commits)
powerpc/86xx: Fix PCI interrupt map definition
powerpc/86xx: Move pci1 definition to the include file
powerpc/fsl: Fix build of the dtb embedded kernel images
powerpc/fsl: Fix rcpm compatible string
powerpc/fsl: Remove FSL_SOC dependency from FSL_LBC
powerpc/fsl-pci: Add a workaround for PCI 5 errata
powerpc/fsl: Fix SPI compatible on t208xrdb and t1040rdb
powerpc/powernv/npu: Add PE to PHB's list
powerpc/powernv: Fix insufficient memory allocation
powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism
Revert "powerpc/eeh: Fix crash in eeh_add_device_early() on Cell"
powerpc/eeh: Drop unnecessary label in eeh_pe_change_owner()
powerpc/eeh: Ignore handlers in eeh_pe_reset_and_recover()
powerpc/eeh: Restore initial state in eeh_pe_reset_and_recover()
powerpc/eeh: Don't report error in eeh_pe_reset_and_recover()
Revert "powerpc/powernv: Exclude root bus in pnv_pci_reset_secondary_bus()"
powerpc/powernv/npu: Enable NVLink pass through
powerpc/powernv/npu: Rework TCE Kill handling
powerpc/powernv/npu: Add set/unset window helpers
powerpc/powernv/ioda2: Export debug helper pe_level_printk()
...
When CONFIG_KVM_XICS is enabled, CPU_UP_PREPARE and other macros for
CPU states in linux/cpu.h are needed by arch/powerpc/kvm/book3s_hv.c.
Otherwise, build error as below is seen:
gwshan@gwshan:~/sandbox/l$ make arch/powerpc/kvm/book3s_hv.o
:
CC arch/powerpc/kvm/book3s_hv.o
arch/powerpc/kvm/book3s_hv.c: In function ‘kvmppc_cpu_notify’:
arch/powerpc/kvm/book3s_hv.c:3072:7: error: ‘CPU_UP_PREPARE’ \
undeclared (first use in this function)
This fixes the issue introduced by commit <6f3bb80944> ("KVM: PPC:
Book3S HV: kvmppc_host_rm_ops - handle offlining CPUs").
Fixes: 6f3bb80944
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerISA 3.0 adds a parition table indexed by LPID. Parition table
allows us to specify the MMU model that will be used for guest and host
translation.
This patch adds support with SLB based hash model (UPRT = 0). What is
required with this model is to support the new hash page table entry
format and also setup partition table such that we use hash table for
address translation.
We don't have segment table support yet.
In order to make sure we don't load KVM module on Power9 (since we don't
have kvm support yet) this patch also disables KVM on Power9.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
but lots of architecture-specific changes.
* ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
* PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
* s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
* x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using vector
hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest memory---currently
its only use is to speedup the legacy shadow paging (pre-EPT) case, but
in the future it will be used for virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJW5r3BAAoJEL/70l94x66D2pMH/jTSWWwdTUJMctrDjPVzKzG0
yOzHW5vSLFoFlwEOY2VpslnXzn5TUVmCAfrdmFNmQcSw6hGb3K/xA/ZX/KLwWhyb
oZpr123ycahga+3q/ht/dFUBCCyWeIVMdsLSFwpobEBzPL0pMgc9joLgdUC6UpWX
tmN0LoCAeS7spC4TTiTTpw3gZ/L+aB0B6CXhOMjldb9q/2CsgaGyoVvKA199nk9o
Ngu7ImDt7l/x1VJX4/6E/17VHuwqAdUrrnbqerB/2oJ5ixsZsHMGzxQ3sHCmvyJx
WG5L00ubB1oAJAs9fBg58Y/MdiWX99XqFhdEfxq4foZEiQuCyxygVvq3JwZTxII=
=OUZZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"One of the largest releases for KVM... Hardly any generic
changes, but lots of architecture-specific updates.
ARM:
- VHE support so that we can run the kernel at EL2 on ARMv8.1 systems
- PMU support for guests
- 32bit world switch rewritten in C
- various optimizations to the vgic save/restore code.
PPC:
- enabled KVM-VFIO integration ("VFIO device")
- optimizations to speed up IPIs between vcpus
- in-kernel handling of IOMMU hypercalls
- support for dynamic DMA windows (DDW).
s390:
- provide the floating point registers via sync regs;
- separated instruction vs. data accesses
- dirty log improvements for huge guests
- bugfixes and documentation improvements.
x86:
- Hyper-V VMBus hypercall userspace exit
- alternative implementation of lowest-priority interrupts using
vector hashing (for better VT-d posted interrupt support)
- fixed guest debugging with nested virtualizations
- improved interrupt tracking in the in-kernel IOAPIC
- generic infrastructure for tracking writes to guest
memory - currently its only use is to speedup the legacy shadow
paging (pre-EPT) case, but in the future it will be used for
virtual GPUs as well
- much cleanup (LAPIC, kvmclock, MMU, PIT), including ubsan fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (217 commits)
KVM: x86: remove eager_fpu field of struct kvm_vcpu_arch
KVM: x86: disable MPX if host did not enable MPX XSAVE features
arm64: KVM: vgic-v3: Only wipe LRs on vcpu exit
arm64: KVM: vgic-v3: Reset LRs at boot time
arm64: KVM: vgic-v3: Do not save an LR known to be empty
arm64: KVM: vgic-v3: Save maintenance interrupt state only if required
arm64: KVM: vgic-v3: Avoid accessing ICH registers
KVM: arm/arm64: vgic-v2: Make GICD_SGIR quicker to hit
KVM: arm/arm64: vgic-v2: Only wipe LRs on vcpu exit
KVM: arm/arm64: vgic-v2: Reset LRs at boot time
KVM: arm/arm64: vgic-v2: Do not save an LR known to be empty
KVM: arm/arm64: vgic-v2: Move GICH_ELRSR saving to its own function
KVM: arm/arm64: vgic-v2: Save maintenance interrupt state only if required
KVM: arm/arm64: vgic-v2: Avoid accessing GICH registers
KVM: s390: allocate only one DMA page per VM
KVM: s390: enable STFLE interpretation only if enabled for the guest
KVM: s390: wake up when the VCPU cpu timer expires
KVM: s390: step the VCPU timer while in enabled wait
KVM: s390: protect VCPU cpu timer with a seqcount
KVM: s390: step VCPU cpu timer during kvm_run ioctl
...
Redirecting the wakeup of a VCPU from the H_IPI hypercall to
a core running in the host is usually a good idea, most workloads
seemed to benefit. However, in one heavily interrupt-driven SMT1
workload, some regression was observed. This patch adds a kvm_hv
module parameter called h_ipi_redirect to control this feature.
The default value for this tunable is 1 - that is enable the feature.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the support for the kick VCPU operation for
kvmppc_host_rm_ops. The kvmppc_xics_ipi_action() function
provides the function to be invoked for a host side operation
when poked by the real mode KVM. This is initiated by KVM by
sending an IPI to any free host core.
KVM real mode must set the rm_action to XICS_RM_KICK_VCPU and
rm_data to point to the VCPU to be woken up before sending the IPI.
Note that we have allocated one kvmppc_host_rm_core structure
per core. The above values need to be set in the structure
corresponding to the core to which the IPI will be sent.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kvmppc_host_rm_ops structure keeps track of which cores are
are in the host by maintaining a bitmask of active/runnable
online CPUs that have not entered the guest. This patch adds
support to manage the bitmask when a CPU is offlined or onlined
in the host.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the core host state in kvmppc_host_rm_ops whenever
the primary thread of the core enters the guest or returns
back.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch defines the data structures to support the setting up
of host side operations while running in real mode in the guest,
and also the functions to allocate and free it.
The operations are for now limited to virtual XICS operations.
Currently, we have only defined one operation in the data
structure:
- Wake up a VCPU sleeping in the host when it
receives a virtual interrupt
The operations are assigned at the core level because PowerKVM
requires that the host run in SMT off mode. For each core,
we will need to manage its state atomically - where the state
is defined by:
1. Is the core running in the host?
2. Is there a Real Mode (RM) operation pending on the host?
Currently, core state is only managed at the whole-core level
even when the system is in split-core mode. This just limits
the number of free or "available" cores in the host to perform
any host-side operations.
The kvmppc_host_rm_core.rm_data allows any data to be passed by
KVM in real mode to the host core along with the operation to
be performed.
The kvmppc_host_rm_ops structure is allocated the very first time
a guest VM is started. Initial core state is also set - all online
cores are in the host. This structure is never deleted, not even
when there are no active guests. However, it needs to be freed
when the module is unloaded because the kvmppc_host_rm_ops_hv
can contain function pointers to kvm-hv.ko functions for the
different supported host operations.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The problem:
On -rt, an emulated LAPIC timer instances has the following path:
1) hard interrupt
2) ksoftirqd is scheduled
3) ksoftirqd wakes up vcpu thread
4) vcpu thread is scheduled
This extra context switch introduces unnecessary latency in the
LAPIC path for a KVM guest.
The solution:
Allow waking up vcpu thread from hardirq context,
thus avoiding the need for ksoftirqd to be scheduled.
Normal waitqueues make use of spinlocks, which on -RT
are sleepable locks. Therefore, waking up a waitqueue
waiter involves locking a sleeping lock, which
is not allowed from hard interrupt context.
cyclictest command line:
This patch reduces the average latency in my tests from 14us to 11us.
Daniel writes:
Paolo asked for numbers from kvm-unit-tests/tscdeadline_latency
benchmark on mainline. The test was run 1000 times on
tip/sched/core 4.4.0-rc8-01134-g0905f04:
./x86-run x86/tscdeadline_latency.flat -cpu host
with idle=poll.
The test seems not to deliver really stable numbers though most of
them are smaller. Paolo write:
"Anything above ~10000 cycles means that the host went to C1 or
lower---the number means more or less nothing in that case.
The mean shows an improvement indeed."
Before:
min max mean std
count 1000.000000 1000.000000 1000.000000 1000.000000
mean 5162.596000 2019270.084000 5824.491541 20681.645558
std 75.431231 622607.723969 89.575700 6492.272062
min 4466.000000 23928.000000 5537.926500 585.864966
25% 5163.000000 1613252.750000 5790.132275 16683.745433
50% 5175.000000 2281919.000000 5834.654000 23151.990026
75% 5190.000000 2382865.750000 5861.412950 24148.206168
max 5228.000000 4175158.000000 6254.827300 46481.048691
After
min max mean std
count 1000.000000 1000.00000 1000.000000 1000.000000
mean 5143.511000 2076886.10300 5813.312474 21207.357565
std 77.668322 610413.09583 86.541500 6331.915127
min 4427.000000 25103.00000 5529.756600 559.187707
25% 5148.000000 1691272.75000 5784.889825 17473.518244
50% 5160.000000 2308328.50000 5832.025000 23464.837068
75% 5172.000000 2393037.75000 5853.177675 24223.969976
max 5222.000000 3922458.00000 6186.720500 42520.379830
[Patch was originaly based on the swait implementation found in the -rt
tree. Daniel ported it to mainline's version and gathered the
benchmark numbers for tscdeadline_latency test.]
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux-rt-users@vger.kernel.org
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1455871601-27484-4-git-send-email-wagi@monom.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This adds real and virtual mode handlers for the H_PUT_TCE_INDIRECT and
H_STUFF_TCE hypercalls for user space emulated devices such as IBMVIO
devices or emulated PCI. These calls allow adding multiple entries
(up to 512) into the TCE table in one call which saves time on
transition between kernel and user space.
The current implementation of kvmppc_h_stuff_tce() allows it to be
executed in both real and virtual modes so there is one helper.
The kvmppc_rm_h_put_tce_indirect() needs to translate the guest address
to the host address and since the translation is different, there are
2 helpers - one for each mode.
This implements the KVM_CAP_PPC_MULTITCE capability. When present,
the kernel will try handling H_PUT_TCE_INDIRECT and H_STUFF_TCE if these
are enabled by the userspace via KVM_CAP_PPC_ENABLE_HCALL.
If they can not be handled by the kernel, they are passed on to
the user space. The user space still has to have an implementation
for these.
Both HV and PR-syle KVM are supported.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
support of 248 VCPUs.
* ARM: rewrite of the arm64 world switch in C, support for
16-bit VM identifiers. Performance counter virtualization
missed the boat.
* x86: Support for more Hyper-V features (synthetic interrupt
controller), MMU cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWlSKwAAoJEL/70l94x66DY0UIAK5vp4zfQoQOJC4KP4Xgxwdu
kpnK2Boz3/74o1b0y5+eJZoUZCsXCVLtmP5uhmMxUYWDgByFG2X8ZDhPFwB5FYLT
2dN+Lr4tsolgIfRdHZtrT6Svp9SDL039bWTdscnbR6l37/j9FRWvpKdhI3orloFD
/i4CSW2dVIq1/9Xctwu/rtcOEesEx4Cad+6YV3/530eVAXFzE908nXfmqJNZTocY
YCGcmrMVCOu0ng5QM4xSzmmYjKMLUcRs+QzZWkVBzdJtTgwZUr09yj7I2dZ1yj/i
cxYrJy6shSwE74XkXsmvG+au3C5u3vX4tnXjBFErnPJ99oqzHatVnFWNRhj4dLQ=
=PIj1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"PPC changes will come next week.
- s390: Support for runtime instrumentation within guests, support of
248 VCPUs.
- ARM: rewrite of the arm64 world switch in C, support for 16-bit VM
identifiers. Performance counter virtualization missed the boat.
- x86: Support for more Hyper-V features (synthetic interrupt
controller), MMU cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (115 commits)
kvm: x86: Fix vmwrite to SECONDARY_VM_EXEC_CONTROL
kvm/x86: Hyper-V SynIC timers tracepoints
kvm/x86: Hyper-V SynIC tracepoints
kvm/x86: Update SynIC timers on guest entry only
kvm/x86: Skip SynIC vector check for QEMU side
kvm/x86: Hyper-V fix SynIC timer disabling condition
kvm/x86: Reorg stimer_expiration() to better control timer restart
kvm/x86: Hyper-V unify stimer_start() and stimer_restart()
kvm/x86: Drop stimer_stop() function
kvm/x86: Hyper-V timers fix incorrect logical operation
KVM: move architecture-dependent requests to arch/
KVM: renumber vcpu->request bits
KVM: document which architecture uses each request bit
KVM: Remove unused KVM_REQ_KICK to save a bit in vcpu->requests
kvm: x86: Check kvm_write_guest return value in kvm_write_wall_clock
KVM: s390: implement the RI support of guest
kvm/s390: drop unpaired smp_mb
kvm: x86: fix comment about {mmu,nested_mmu}.gva_to_gpa
KVM: x86: MMU: Use clear_page() instead of init_shadow_page_table()
arm/arm64: KVM: Detect vGIC presence at runtime
...
Currently it is possible for userspace (e.g. QEMU) to set a value
for the MSR for a guest VCPU which has both of the TS bits set,
which is an illegal combination. The result of this is that when
we execute a hrfid (hypervisor return from interrupt doubleword)
instruction to enter the guest, the CPU will take a TM Bad Thing
type of program interrupt (vector 0x700).
Now, if PR KVM is configured in the kernel along with HV KVM, we
actually handle this without crashing the host or giving hypervisor
privilege to the guest; instead what happens is that we deliver a
program interrupt to the guest, with SRR0 reflecting the address
of the hrfid instruction and SRR1 containing the MSR value at that
point. If PR KVM is not configured in the kernel, then we try to
run the host's program interrupt handler with the MMU set to the
guest context, which almost certainly causes a host crash.
This closes the hole by making kvmppc_set_msr_hv() check for the
illegal combination and force the TS field to a safe value (00,
meaning non-transactional).
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Paul Mackerras <paulus@samba.org>
As we saw with the TM Bad Thing type of program interrupt occurring
on the hrfid that enters the guest, it is not completely impossible
to have a trap occurring in the guest entry/exit code, despite the
fact that the code has been written to avoid taking any traps.
This adds a check in the kvmppc_handle_exit_hv() function to detect
the case when a trap has occurred in the hypervisor-mode code, and
instead of treating it just like a trap in guest code, we now print
a message and return to userspace with a KVM_EXIT_INTERNAL_ERROR
exit reason.
Of the various interrupts that get handled in the assembly code in
the guest exit path and that can return directly to the guest, the
only one that can occur when MSR.HV=1 and MSR.EE=0 is machine check
(other than system call, which we can avoid just by not doing a sc
instruction). Therefore this adds code to the machine check path to
ensure that if the MCE occurred in hypervisor mode, we exit to the
host rather than trying to continue the guest.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Create a single function that flushes everything (FP, VMX, VSX, SPE).
Doing this all at once means we only do one MSR write.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Let's reuse the new common function for VPCU lookup by id.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split out the new function into a separate patch]
- x86: work around two nasty cases where a benign exception occurs while
another is being delivered. The endless stream of exceptions causes an
infinite loop in the processor, which not even NMIs or SMIs can interrupt;
in the virt case, there is no possibility to exit to the host either.
- x86: support for Skylake per-guest TSC rate. Long supported by AMD,
the patches mostly move things from there to common arch/x86/kvm/ code.
- generic: remove local_irq_save/restore from the guest entry and exit
paths when context tracking is enabled. The patches are a few months
old, but we discussed them again at kernel summit. Andy will pick up
from here and, in 4.5, try to remove it from the user entry/exit paths.
- PPC: Two bug fixes, see merge commit 370289756b for details.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWRFb0AAoJEL/70l94x66DjjMH/31jr8d119MW0uv2x+03+wRq
6dbJ8tjQ8grvBRExKvLsUVjDmHlhCa1BQl5qjCsyYhX9UeAf4NQOmoEFpq+YTLxh
Ctveyn+yiZWC7qxbQDmauiQ4JCOp+W9ial782iqw5+ouQMajGOffq5WrojCa2ZNF
jI278JgdHJLrKj/uie//WBu3V7MJY5Apc3p4zatnSYFSQ3MA0sxl4r4zIrwOa5qs
23ZeeoqbP4sHh4X5wL/30Y6XFSCHj0qoYHHyAgzLi0PCMvBdt4DrAFUPDG/Rhlv6
o1WB/kcUfcz3DtBX85wfSOMuw0nF6patWhWv07R/3EIbYoz3dKvp9d6ORYgXqlY=
=Um9M
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of kvm updates from Paolo Bonzini:
"Four changes:
- x86: work around two nasty cases where a benign exception occurs
while another is being delivered. The endless stream of exceptions
causes an infinite loop in the processor, which not even NMIs or
SMIs can interrupt; in the virt case, there is no possibility to
exit to the host either.
- x86: support for Skylake per-guest TSC rate. Long supported by
AMD, the patches mostly move things from there to common
arch/x86/kvm/ code.
- generic: remove local_irq_save/restore from the guest entry and
exit paths when context tracking is enabled. The patches are a few
months old, but we discussed them again at kernel summit. Andy
will pick up from here and, in 4.5, try to remove it from the user
entry/exit paths.
- PPC: Two bug fixes, see merge commit 370289756b for details"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: x86: rename update_db_bp_intercept to update_bp_intercept
KVM: svm: unconditionally intercept #DB
KVM: x86: work around infinite loop in microcode when #AC is delivered
context_tracking: avoid irq_save/irq_restore on guest entry and exit
context_tracking: remove duplicate enabled check
KVM: VMX: Dump TSC multiplier in dump_vmcs()
KVM: VMX: Use a scaled host TSC for guest readings of MSR_IA32_TSC
KVM: VMX: Setup TSC scaling ratio when a vcpu is loaded
KVM: VMX: Enable and initialize VMX TSC scaling
KVM: x86: Use the correct vcpu's TSC rate to compute time scale
KVM: x86: Move TSC scaling logic out of call-back read_l1_tsc()
KVM: x86: Move TSC scaling logic out of call-back adjust_tsc_offset()
KVM: x86: Replace call-back compute_tsc_offset() with a common function
KVM: x86: Replace call-back set_tsc_khz() with a common function
KVM: x86: Add a common TSC scaling function
KVM: x86: Add a common TSC scaling ratio field in kvm_vcpu_arch
KVM: x86: Collect information for setting TSC scaling ratio
KVM: x86: declare a few variables as __read_mostly
KVM: x86: merge handle_mmio_page_fault and handle_mmio_page_fault_common
KVM: PPC: Book3S HV: Don't dynamically split core when already split
...
In static micro-threading modes, the dynamic micro-threading code
is supposed to be disabled, because subcores can't make independent
decisions about what micro-threading mode to put the core in - there is
only one micro-threading mode for the whole core. The code that
implements dynamic micro-threading checks for this, except that the
check was missed in one case. This means that it is possible for a
subcore in static 2-way micro-threading mode to try to put the core
into 4-way micro-threading mode, which usually leads to stuck CPUs,
spinlock lockups, and other stalls in the host.
The problem was in the can_split_piggybacked_subcores() function, which
should always return false if the system is in a static micro-threading
mode. This fixes the problem by making can_split_piggybacked_subcores()
use subcore_config_ok() for its checks, as subcore_config_ok() includes
the necessary check for the static micro-threading modes.
Credit to Gautham Shenoy for working out that the reason for the hangs
and stalls we were seeing was that we were trying to do dynamic 4-way
micro-threading while we were in static 2-way mode.
Fixes: b4deba5c41
Cc: vger@stable.kernel.org # v4.3
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 9678cdaae9 ("Use the POWER8 Micro Partition
Prefetch Engine in KVM HV on POWER8") because the original commit had
multiple, partly self-cancelling bugs, that could cause occasional
memory corruption.
In fact the logmpp instruction was incorrectly using register r0 as the
source of the buffer address and operation code, and depending on what
was in r0, it would either do nothing or corrupt the 64k page pointed to
by r0.
The logmpp instruction encoding and the operation code definitions could
be corrected, but then there is the problem that there is no clearly
defined way to know when the hardware has finished writing to the
buffer.
The original commit attempted to work around this by aborting the
write-out before starting the prefetch, but this is ineffective in the
case where the virtual core is now executing on a different physical
core from the one where the write-out was initiated.
These problems plus advice from the hardware designers not to use the
function (since the measured performance improvement from using the
feature was actually mostly negative), mean that reverting the code is
the best option.
Fixes: 9678cdaae9 ("Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8")
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a bug which results in stale vcore pointers being left in
the per-cpu preempted vcore lists when a VM is destroyed. The result
of the stale vcore pointers is usually either a crash or a lockup
inside collect_piggybacks() when another VM is run. A typical
lockup message looks like:
[ 472.161074] NMI watchdog: BUG: soft lockup - CPU#24 stuck for 22s! [qemu-system-ppc:7039]
[ 472.161204] Modules linked in: kvm_hv kvm_pr kvm xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ses enclosure shpchp rtc_opal i2c_opal powernv_rng binfmt_misc dm_service_time scsi_dh_alua radeon i2c_algo_bit drm_kms_helper ttm drm tg3 ptp pps_core cxgb3 ipr i2c_core mdio dm_multipath [last unloaded: kvm_hv]
[ 472.162111] CPU: 24 PID: 7039 Comm: qemu-system-ppc Not tainted 4.2.0-kvm+ #49
[ 472.162187] task: c000001e38512750 ti: c000001e41bfc000 task.ti: c000001e41bfc000
[ 472.162262] NIP: c00000000096b094 LR: c00000000096b08c CTR: c000000000111130
[ 472.162337] REGS: c000001e41bff520 TRAP: 0901 Not tainted (4.2.0-kvm+)
[ 472.162399] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 24848844 XER: 00000000
[ 472.162588] CFAR: c00000000096b0ac SOFTE: 1
GPR00: c000000000111170 c000001e41bff7a0 c00000000127df00 0000000000000001
GPR04: 0000000000000003 0000000000000001 0000000000000000 0000000000874821
GPR08: c000001e41bff8e0 0000000000000001 0000000000000000 d00000000efde740
GPR12: c000000000111130 c00000000fdae400
[ 472.163053] NIP [c00000000096b094] _raw_spin_lock_irqsave+0xa4/0x130
[ 472.163117] LR [c00000000096b08c] _raw_spin_lock_irqsave+0x9c/0x130
[ 472.163179] Call Trace:
[ 472.163206] [c000001e41bff7a0] [c000001e41bff7f0] 0xc000001e41bff7f0 (unreliable)
[ 472.163295] [c000001e41bff7e0] [c000000000111170] __wake_up+0x40/0x90
[ 472.163375] [c000001e41bff830] [d00000000efd6fc0] kvmppc_run_core+0x1240/0x1950 [kvm_hv]
[ 472.163465] [c000001e41bffa30] [d00000000efd8510] kvmppc_vcpu_run_hv+0x5a0/0xd90 [kvm_hv]
[ 472.163559] [c000001e41bffb70] [d00000000e9318a4] kvmppc_vcpu_run+0x44/0x60 [kvm]
[ 472.163653] [c000001e41bffba0] [d00000000e92e674] kvm_arch_vcpu_ioctl_run+0x64/0x170 [kvm]
[ 472.163745] [c000001e41bffbe0] [d00000000e9263a8] kvm_vcpu_ioctl+0x538/0x7b0 [kvm]
[ 472.163834] [c000001e41bffd40] [c0000000002d0f50] do_vfs_ioctl+0x480/0x7c0
[ 472.163910] [c000001e41bffde0] [c0000000002d1364] SyS_ioctl+0xd4/0xf0
[ 472.163986] [c000001e41bffe30] [c000000000009260] system_call+0x38/0xd0
[ 472.164060] Instruction dump:
[ 472.164098] ebc1fff0 ebe1fff8 7c0803a6 4e800020 60000000 60000000 60420000 8bad02e2
[ 472.164224] 7fc3f378 4b6a57c1 60000000 7c210b78 <e92d0000> 89290009 792affe3 40820070
The bug is that kvmppc_run_vcpu does not correctly handle the case
where a vcpu task receives a signal while its guest vcpu is executing
in the guest as a result of being piggy-backed onto the execution of
another vcore. In that case we need to wait for the vcpu to finish
executing inside the guest, and then remove this vcore from the
preempted vcores list. That way, we avoid leaving this vcpu's vcore
on the preempted vcores list when the vcpu gets interrupted.
Fixes: ec25716508
Reported-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current dynamic micro-threading code has a race due to which a
secondary thread naps when it is supposed to be running a vcpu. As a
side effect of this, on a guest exit, the primary thread in
kvmppc_wait_for_nap() finds that this secondary thread hasn't cleared
its vcore pointer. This results in "CPU X seems to be stuck!"
warnings.
The race is possible since the primary thread on exiting the guests
only waits for all the secondaries to clear its vcore pointer. It
subsequently expects the secondary threads to enter nap while it
unsplits the core. A secondary thread which hasn't yet entered the nap
will loop in kvm_no_guest until its vcore pointer and the do_nap flag
are unset. Once the core has been unsplit, a new vcpu thread can grab
the core and set the do_nap flag *before* setting the vcore pointers
of the secondary. As a result, the secondary thread will now enter nap
via kvm_unsplit_nap instead of running the guest vcpu.
Fix this by setting the do_nap flag after setting the vcore pointer in
the PACA of the secondary in kvmppc_run_core. Also, ensure that a
secondary thread doesn't nap in kvm_unsplit_nap when the vcore pointer
in its PACA struct is set.
Fixes: b4deba5c41
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Whenever a vcore state is VCORE_PREEMPT we need to be counting stolen
time for it. This currently isn't the case when we have a vcore that
no longer has any runnable threads in it but still has a runner task,
so we do an explicit call to kvmppc_core_start_stolen() in that case.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When a vcore gets preempted, we put it on the preempted vcore list for
the current CPU. The runner task then calls schedule() and comes back
some time later and takes itself off the list. We need to be careful
to lock the list that it was put onto, which may not be the list for the
current CPU since the runner task may have moved to another CPU.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This builds on the ability to run more than one vcore on a physical
core by using the micro-threading (split-core) modes of the POWER8
chip. Previously, only vcores from the same VM could be run together,
and (on POWER8) only if they had just one thread per core. With the
ability to split the core on guest entry and unsplit it on guest exit,
we can run up to 8 vcpu threads from up to 4 different VMs, and we can
run multiple vcores with 2 or 4 vcpus per vcore.
Dynamic micro-threading is only available if the static configuration
of the cores is whole-core mode (unsplit), and only on POWER8.
To manage this, we introduce a new kvm_split_mode struct which is
shared across all of the subcores in the core, with a pointer in the
paca on each thread. In addition we extend the core_info struct to
have information on each subcore. When deciding whether to add a
vcore to the set already on the core, we now have two possibilities:
(a) piggyback the vcore onto an existing subcore, or (b) start a new
subcore.
Currently, when any vcpu needs to exit the guest and switch to host
virtual mode, we interrupt all the threads in all subcores and switch
the core back to whole-core mode. It may be possible in future to
allow some of the subcores to keep executing in the guest while
subcore 0 switches to the host, but that is not implemented in this
patch.
This adds a module parameter called dynamic_mt_modes which controls
which micro-threading (split-core) modes the code will consider, as a
bitmap. In other words, if it is 0, no micro-threading mode is
considered; if it is 2, only 2-way micro-threading is considered; if
it is 4, only 4-way, and if it is 6, both 2-way and 4-way
micro-threading mode will be considered. The default is 6.
With this, we now have secondary threads which are the primary thread
for their subcore and therefore need to do the MMU switch. These
threads will need to be started even if they have no vcpu to run, so
we use the vcore pointer in the PACA rather than the vcpu pointer to
trigger them.
It is now possible for thread 0 to find that an exit has been
requested before it gets to switch the subcore state to the guest. In
that case we haven't added the guest's timebase offset to the
timebase, so we need to be careful not to subtract the offset in the
guest exit path. In fact we just skip the whole path that switches
back to host context, since we haven't switched to the guest context.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running a virtual core of a guest that is configured with fewer
threads per core than the physical cores have, the extra physical
threads are currently unused. This makes it possible to use them to
run one or more other virtual cores from the same guest when certain
conditions are met. This applies on POWER7, and on POWER8 to guests
with one thread per virtual core. (It doesn't apply to POWER8 guests
with multiple threads per vcore because they require a 1-1 virtual to
physical thread mapping in order to be able to use msgsndp and the
TIR.)
The idea is that we maintain a list of preempted vcores for each
physical cpu (i.e. each core, since the host runs single-threaded).
Then, when a vcore is about to run, it checks to see if there are
any vcores on the list for its physical cpu that could be
piggybacked onto this vcore's execution. If so, those additional
vcores are put into state VCORE_PIGGYBACK and their runnable VCPU
threads are started as well as the original vcore, which is called
the master vcore.
After the vcores have exited the guest, the extra ones are put back
onto the preempted list if any of their VCPUs are still runnable and
not idle.
This means that vcpu->arch.ptid is no longer necessarily the same as
the physical thread that the vcpu runs on. In order to make it easier
for code that wants to send an IPI to know which CPU to target, we
now store that in a new field in struct vcpu_arch, called thread_cpu.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When compiling the KVM code for POWER with "make C=1", sparse
complains about functions missing proper prototypes and a 64-bit
constant missing the ULL prefix. Let's fix this by making the
functions static or by including the proper header with the
prototypes, and by appending a ULL prefix to the constant
PPC_MPPE_ADDRESS_MASK.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Function should_resched() is equal to (!preempt_count() && need_resched()).
In preemptive kernel preempt_count here is non-zero because of vc->lock.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150715095203.12246.72922.stgit@buzz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This lets the function access the new memory slot without going through
kvm_memslots and id_to_memslot. It will simplify the code when more
than one address space will be supported.
Unfortunately, the "const"ness of the new argument must be casted
away in two places. Fixing KVM to accept const struct kvm_memory_slot
pointers would require modifications in pretty much all architectures,
and is left for later.
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Architecture-specific helpers are not supposed to muck with
struct kvm_userspace_memory_region contents. Add const to
enforce this.
In order to eliminate the only write in __kvm_set_memory_region,
the cleaning of deleted slots is pulled up from update_memslots
to __kvm_set_memory_region.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_memslots provides lockdep checking. Use it consistently instead of
explicit dereferencing of kvm->memslots.
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes a regression introduced in commit 25fedfca94, "KVM: PPC:
Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu", which
leads to a user-triggerable oops.
In the case where we try to run a vcore on a physical core that is
not in single-threaded mode, or the vcore has too many threads for
the physical core, we iterate the list of runnable vcpus to make
each one return an EBUSY error to userspace. Since this involves
taking each vcpu off the runnable_threads list for the vcore, we
need to use list_for_each_entry_safe rather than list_for_each_entry
to traverse the list. Otherwise the kernel will crash with an oops
message like this:
Unable to handle kernel paging request for data at address 0x000fff88
Faulting instruction address: 0xd00000001e635dc8
Oops: Kernel access of bad area, sig: 11 [#2]
SMP NR_CPUS=1024 NUMA PowerNV
...
CPU: 48 PID: 91256 Comm: qemu-system-ppc Tainted: G D 3.18.0 #1
task: c00000274e507500 ti: c0000027d1924000 task.ti: c0000027d1924000
NIP: d00000001e635dc8 LR: d00000001e635df8 CTR: c00000000011ba50
REGS: c0000027d19275b0 TRAP: 0300 Tainted: G D (3.18.0)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 22002824 XER: 00000000
CFAR: c000000000008468 DAR: 00000000000fff88 DSISR: 40000000 SOFTE: 1
GPR00: d00000001e635df8 c0000027d1927830 d00000001e64c850 0000000000000001
GPR04: 0000000000000001 0000000000000001 0000000000000000 0000000000000000
GPR08: 0000000000200200 0000000000000000 0000000000000000 d00000001e63e588
GPR12: 0000000000002200 c000000007dbc800 c000000fc7800000 000000000000000a
GPR16: fffffffffffffffc c000000fd5439690 c000000fc7801c98 0000000000000001
GPR20: 0000000000000003 c0000027d1927aa8 c000000fd543b348 c000000fd543b350
GPR24: 0000000000000000 c000000fa57f0000 0000000000000030 0000000000000000
GPR28: fffffffffffffff0 c000000fd543b328 00000000000fe468 c000000fd543b300
NIP [d00000001e635dc8] kvmppc_run_core+0x198/0x17c0 [kvm_hv]
LR [d00000001e635df8] kvmppc_run_core+0x1c8/0x17c0 [kvm_hv]
Call Trace:
[c0000027d1927830] [d00000001e635df8] kvmppc_run_core+0x1c8/0x17c0 [kvm_hv] (unreliable)
[c0000027d1927a30] [d00000001e638350] kvmppc_vcpu_run_hv+0x5b0/0xdd0 [kvm_hv]
[c0000027d1927b70] [d00000001e510504] kvmppc_vcpu_run+0x44/0x60 [kvm]
[c0000027d1927ba0] [d00000001e50d4a4] kvm_arch_vcpu_ioctl_run+0x64/0x170 [kvm]
[c0000027d1927be0] [d00000001e504be8] kvm_vcpu_ioctl+0x5e8/0x7a0 [kvm]
[c0000027d1927d40] [c0000000002d6720] do_vfs_ioctl+0x490/0x780
[c0000027d1927de0] [c0000000002d6ae4] SyS_ioctl+0xd4/0xf0
[c0000027d1927e30] [c000000000009358] syscall_exit+0x0/0x98
Instruction dump:
60000000 60420000 387e1b30 38800003 38a00001 38c00000 480087d9 e8410018
ebde1c98 7fbdf040 3bdee368 419e0048 <813e1b20> 939e1b18 2f890001 409effcc
---[ end trace 8cdf50251cca6680 ]---
Fixes: 25fedfca94
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This uses msgsnd where possible for signalling other threads within
the same core on POWER8 systems, rather than IPIs through the XICS
interrupt controller. This includes waking secondary threads to run
the guest, the interrupts generated by the virtual XICS, and the
interrupts to bring the other threads out of the guest when exiting.
Aggregated statistics from debugfs across vcpus for a guest with 32
vcpus, 8 threads/vcore, running on a POWER8, show this before the
change:
rm_entry: 3387.6ns (228 - 86600, 1008969 samples)
rm_exit: 4561.5ns (12 - 3477452, 1009402 samples)
rm_intr: 1660.0ns (12 - 553050, 3600051 samples)
and this after the change:
rm_entry: 3060.1ns (212 - 65138, 953873 samples)
rm_exit: 4244.1ns (12 - 9693408, 954331 samples)
rm_intr: 1342.3ns (12 - 1104718, 3405326 samples)
for a test of booting Fedora 20 big-endian to the login prompt.
The time taken for a H_PROD hcall (which is handled in the host
kernel) went down from about 35 microseconds to about 16 microseconds
with this change.
The noinline added to kvmppc_run_core turned out to be necessary for
good performance, at least with gcc 4.9.2 as packaged with Fedora 21
and a little-endian POWER8 host.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, the entry_exit_count field in the kvmppc_vcore struct
contains two 8-bit counts, one of the threads that have started entering
the guest, and one of the threads that have started exiting the guest.
This changes it to an entry_exit_map field which contains two bitmaps
of 8 bits each. The advantage of doing this is that it gives us a
bitmap of which threads need to be signalled when exiting the guest.
That means that we no longer need to use the trick of setting the
HDEC to 0 to pull the other threads out of the guest, which led in
some cases to a spurious HDEC interrupt on the next guest entry.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We can tell when a secondary thread has finished running a guest by
the fact that it clears its kvm_hstate.kvm_vcpu pointer, so there
is no real need for the nap_count field in the kvmppc_vcore struct.
This changes kvmppc_wait_for_nap to poll the kvm_hstate.kvm_vcpu
pointers of the secondary threads rather than polling vc->nap_count.
Besides reducing the size of the kvmppc_vcore struct by 8 bytes,
this also means that we can tell which secondary threads have got
stuck and thus print a more informative error message.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rather than calling cond_resched() in kvmppc_run_core() before doing
the post-processing for the vcpus that we have just run (that is,
calling kvmppc_handle_exit_hv(), kvmppc_set_timer(), etc.), we now do
that post-processing before calling cond_resched(), and that post-
processing is moved out into its own function, post_guest_process().
The reschedule point is now in kvmppc_run_vcpu() and we define a new
vcore state, VCORE_PREEMPT, to indicate that that the vcore's runner
task is runnable but not running. (Doing the reschedule with the
vcore in VCORE_INACTIVE state would be bad because there are potentially
other vcpus waiting for the runner in kvmppc_wait_for_exec() which
then wouldn't get woken up.)
Also, we make use of the handy cond_resched_lock() function, which
unlocks and relocks vc->lock for us around the reschedule.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Previously, if kvmppc_run_core() was running a VCPU that needed a VPA
update (i.e. one of its 3 virtual processor areas needed to be pinned
in memory so the host real mode code can update it on guest entry and
exit), we would drop the vcore lock and do the update there and then.
Future changes will make it inconvenient to drop the lock, so instead
we now remove it from the list of runnable VCPUs and wake up its
VCPU task. This will have the effect that the VCPU task will exit
kvmppc_run_vcpu(), go around the do loop in kvmppc_vcpu_run_hv(), and
re-enter kvmppc_run_vcpu(), whereupon it will do the necessary call
to kvmppc_update_vpas() and then rejoin the vcore.
The one complication is that the runner VCPU (whose VCPU task is the
current task) might be one of the ones that gets removed from the
runnable list. In that case we just return from kvmppc_run_core()
and let the code in kvmppc_run_vcpu() wake up another VCPU task to be
the runner if necessary.
This all means that the VCORE_STARTING state is no longer used, so we
remove it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reads the timebase at various points in the real-mode guest
entry/exit code and uses that to accumulate total, minimum and
maximum time spent in those parts of the code. Currently these
times are accumulated per vcpu in 5 parts of the code:
* rm_entry - time taken from the start of kvmppc_hv_entry() until
just before entering the guest.
* rm_intr - time from when we take a hypervisor interrupt in the
guest until we either re-enter the guest or decide to exit to the
host. This includes time spent handling hcalls in real mode.
* rm_exit - time from when we decide to exit the guest until the
return from kvmppc_hv_entry().
* guest - time spend in the guest
* cede - time spent napping in real mode due to an H_CEDE hcall
while other threads in the same vcore are active.
These times are exposed in debugfs in a directory per vcpu that
contains a file called "timings". This file contains one line for
each of the 5 timings above, with the name followed by a colon and
4 numbers, which are the count (number of times the code has been
executed), the total time, the minimum time, and the maximum time,
all in nanoseconds.
The overhead of the extra code amounts to about 30ns for an hcall that
is handled in real mode (e.g. H_SET_DABR), which is about 25%. Since
production environments may not wish to incur this overhead, the new
code is conditional on a new config symbol,
CONFIG_KVM_BOOK3S_HV_EXIT_TIMING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This creates a debugfs directory for each HV guest (assuming debugfs
is enabled in the kernel config), and within that directory, a file
by which the contents of the guest's HPT (hashed page table) can be
read. The directory is named vmnnnn, where nnnn is the PID of the
process that created the guest. The file is named "htab". This is
intended to help in debugging problems in the host's management
of guest memory.
The contents of the file consist of a series of lines like this:
3f48 4000d032bf003505 0000000bd7ff1196 00000003b5c71196
The first field is the index of the entry in the HPT, the second and
third are the HPT entry, so the third entry contains the real page
number that is mapped by the entry if the entry's valid bit is set.
The fourth field is the guest's view of the second doubleword of the
entry, so it contains the guest physical address. (The format of the
second through fourth fields are described in the Power ISA and also
in arch/powerpc/include/asm/mmu-hash64.h.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
We don't support real-mode areas now that 970 support is removed.
Remove the remaining details of rma from the code. Also rename
rma_setup_done to hpte_setup_done to better reflect the changes.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
On POWER, storage caching is usually configured via the MMU - attributes
such as cache-inhibited are stored in the TLB and the hashed page table.
This makes correctly performing cache inhibited IO accesses awkward when
the MMU is turned off (real mode). Some CPU models provide special
registers to control the cache attributes of real mode load and stores but
this is not at all consistent. This is a problem in particular for SLOF,
the firmware used on KVM guests, which runs entirely in real mode, but
which needs to do IO to load the kernel.
To simplify this qemu implements two special hypercalls, H_LOGICAL_CI_LOAD
and H_LOGICAL_CI_STORE which simulate a cache-inhibited load or store to
a logical address (aka guest physical address). SLOF uses these for IO.
However, because these are implemented within qemu, not the host kernel,
these bypass any IO devices emulated within KVM itself. The simplest way
to see this problem is to attempt to boot a KVM guest from a virtio-blk
device with iothread / dataplane enabled. The iothread code relies on an
in kernel implementation of the virtio queue notification, which is not
triggered by the IO hcalls, and so the guest will stall in SLOF unable to
load the guest OS.
This patch addresses this by providing in-kernel implementations of the
2 hypercalls, which correctly scan the KVM IO bus. Any access to an
address not handled by the KVM IO bus will cause a VM exit, hitting the
qemu implementation as before.
Note that a userspace change is also required, in order to enable these
new hcall implementations with KVM_CAP_PPC_ENABLE_HCALL.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[agraf: fix compilation]
Signed-off-by: Alexander Graf <agraf@suse.de>
The VPA (virtual processor area) is defined by PAPR and is therefore
big-endian, so we need a be32_to_cpu when reading it in
kvmppc_get_yield_count(). Without this, H_CONFER always fails on a
little-endian host, causing SMP guests to waste time spinning on
spinlocks.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the H_CONFER hcall is implemented in kernel virtual mode,
meaning that whenever a guest thread does an H_CONFER, all the threads
in that virtual core have to exit the guest. This is bad for
performance because it interrupts the other threads even if they
are doing useful work.
The H_CONFER hcall is called by a guest VCPU when it is spinning on a
spinlock and it detects that the spinlock is held by a guest VCPU that
is currently not running on a physical CPU. The idea is to give this
VCPU's time slice to the holder VCPU so that it can make progress
towards releasing the lock.
To avoid having the other threads exit the guest unnecessarily,
we add a real-mode implementation of H_CONFER that checks whether
the other threads are doing anything. If all the other threads
are idle (i.e. in H_CEDE) or trying to confer (i.e. in H_CONFER),
it returns H_TOO_HARD which causes a guest exit and allows the
H_CONFER to be handled in virtual mode.
Otherwise it spins for a short time (up to 10 microseconds) to give
other threads the chance to observe that this thread is trying to
confer. The spin loop also terminates when any thread exits the guest
or when all other threads are idle or trying to confer. If the
timeout is reached, the H_CONFER returns H_SUCCESS. In this case the
guest VCPU will recheck the spinlock word and most likely call
H_CONFER again.
This also improves the implementation of the H_CONFER virtual mode
handler. If the VCPU is part of a virtual core (vcore) which is
runnable, there will be a 'runner' VCPU which has taken responsibility
for running the vcore. In this case we yield to the runner VCPU
rather than the target VCPU.
We also introduce a check on the target VCPU's yield count: if it
differs from the yield count passed to H_CONFER, the target VCPU
has run since H_CONFER was called and may have already released
the lock. This check is required by PAPR.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There are two ways in which a guest instruction can be obtained from
the guest in the guest exit code in book3s_hv_rmhandlers.S. If the
exit was caused by a Hypervisor Emulation interrupt (i.e. an illegal
instruction), the offending instruction is in the HEIR register
(Hypervisor Emulation Instruction Register). If the exit was caused
by a load or store to an emulated MMIO device, we load the instruction
from the guest by turning data relocation on and loading the instruction
with an lwz instruction.
Unfortunately, in the case where the guest has opposite endianness to
the host, these two methods give results of different endianness, but
both get put into vcpu->arch.last_inst. The HEIR value has been loaded
using guest endianness, whereas the lwz will load the instruction using
host endianness. The rest of the code that uses vcpu->arch.last_inst
assumes it was loaded using host endianness.
To fix this, we define a new vcpu field to store the HEIR value. Then,
in kvmppc_handle_exit_hv(), we transfer the value from this new field to
vcpu->arch.last_inst, doing a byte-swap if the guest and host endianness
differ.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This removes the code that was added to enable HV KVM to work
on PPC970 processors. The PPC970 is an old CPU that doesn't
support virtualizing guest memory. Removing PPC970 support also
lets us remove the code for allocating and managing contiguous
real-mode areas, the code for the !kvm->arch.using_mmu_notifiers
case, the code for pinning pages of guest memory when first
accessed and keeping track of which pages have been pinned, and
the code for handling H_ENTER hypercalls in virtual mode.
Book3S HV KVM is now supported only on POWER7 and POWER8 processors.
The KVM_CAP_PPC_RMA capability now always returns 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds trace points in the guest entry and exit code and also
for exceptions handled by the host in kernel mode - hypercalls and page
faults. The new events are added to /sys/kernel/debug/tracing/events
under a new subsystem called kvm_hv.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the calculations of stolen time for PPC Book3S HV guests
uses fields in both the vcpu struct and the kvmppc_vcore struct. The
fields in the kvmppc_vcore struct are protected by the
vcpu->arch.tbacct_lock of the vcpu that has taken responsibility for
running the virtual core. This works correctly but confuses lockdep,
because it sees that the code takes the tbacct_lock for a vcpu in
kvmppc_remove_runnable() and then takes another vcpu's tbacct_lock in
vcore_stolen_time(), and it thinks there is a possibility of deadlock,
causing it to print reports like this:
=============================================
[ INFO: possible recursive locking detected ]
3.18.0-rc7-kvm-00016-g8db4bc6 #89 Not tainted
---------------------------------------------
qemu-system-ppc/6188 is trying to acquire lock:
(&(&vcpu->arch.tbacct_lock)->rlock){......}, at: [<d00000000ecb1fe8>] .vcore_stolen_time+0x48/0xd0 [kvm_hv]
but task is already holding lock:
(&(&vcpu->arch.tbacct_lock)->rlock){......}, at: [<d00000000ecb25a0>] .kvmppc_remove_runnable.part.3+0x30/0xd0 [kvm_hv]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&vcpu->arch.tbacct_lock)->rlock);
lock(&(&vcpu->arch.tbacct_lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by qemu-system-ppc/6188:
#0: (&vcpu->mutex){+.+.+.}, at: [<d00000000eb93f98>] .vcpu_load+0x28/0xe0 [kvm]
#1: (&(&vcore->lock)->rlock){+.+...}, at: [<d00000000ecb41b0>] .kvmppc_vcpu_run_hv+0x530/0x1530 [kvm_hv]
#2: (&(&vcpu->arch.tbacct_lock)->rlock){......}, at: [<d00000000ecb25a0>] .kvmppc_remove_runnable.part.3+0x30/0xd0 [kvm_hv]
stack backtrace:
CPU: 40 PID: 6188 Comm: qemu-system-ppc Not tainted 3.18.0-rc7-kvm-00016-g8db4bc6 #89
Call Trace:
[c000000b2754f3f0] [c000000000b31b6c] .dump_stack+0x88/0xb4 (unreliable)
[c000000b2754f470] [c0000000000faeb8] .__lock_acquire+0x1878/0x2190
[c000000b2754f600] [c0000000000fbf0c] .lock_acquire+0xcc/0x1a0
[c000000b2754f6d0] [c000000000b2954c] ._raw_spin_lock_irq+0x4c/0x70
[c000000b2754f760] [d00000000ecb1fe8] .vcore_stolen_time+0x48/0xd0 [kvm_hv]
[c000000b2754f7f0] [d00000000ecb25b4] .kvmppc_remove_runnable.part.3+0x44/0xd0 [kvm_hv]
[c000000b2754f880] [d00000000ecb43ec] .kvmppc_vcpu_run_hv+0x76c/0x1530 [kvm_hv]
[c000000b2754f9f0] [d00000000eb9f46c] .kvmppc_vcpu_run+0x2c/0x40 [kvm]
[c000000b2754fa60] [d00000000eb9c9a4] .kvm_arch_vcpu_ioctl_run+0x54/0x160 [kvm]
[c000000b2754faf0] [d00000000eb94538] .kvm_vcpu_ioctl+0x498/0x760 [kvm]
[c000000b2754fcb0] [c000000000267eb4] .do_vfs_ioctl+0x444/0x770
[c000000b2754fd90] [c0000000002682a4] .SyS_ioctl+0xc4/0xe0
[c000000b2754fe30] [c0000000000092e4] syscall_exit+0x0/0x98
In order to make the locking easier to analyse, we change the code to
use a spinlock in the kvmppc_vcore struct to protect the stolen_tb and
preempt_tb fields. This lock needs to be an irq-safe lock since it is
used in the kvmppc_core_vcpu_load_hv() and kvmppc_core_vcpu_put_hv()
functions, which are called with the scheduler rq lock held, which is
an irq-safe lock.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The kvmppc_vcore_blocked() code does not check for the wait condition
after putting the process on the wait queue. This means that it is
possible for an external interrupt to become pending, but the vcpu to
remain asleep until the next decrementer interrupt. The fix is to
make one last check for pending exceptions and ceded state before
calling schedule().
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds kernel side support for software breakpoint.
Design is that, by using an illegal instruction, we trap to hypervisor
via Emulation Assistance interrupt, where we check for the illegal instruction
and accordingly we return to Host or Guest. Patch also adds support for
software breakpoint in PR KVM.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since the guest can read the machine's PVR (Processor Version Register)
directly and see the real value, we should disallow userspace from
setting any value for the guest's PVR other than the real host value.
Therefore this makes kvm_arch_vcpu_set_sregs_hv() check the supplied
PVR value and return an error if it is different from the host value,
which has been put into vcpu->arch.pvr at vcpu creation time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Occasional failures have been seen with split-core mode and migration
where the message "KVM: couldn't grab cpu" appears. This increases
the length of time that we wait from 1ms to 10ms, which seems to
work around the issue.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When calculating the lower bits of AVA field, use the shift
count based on the base page size. Also add the missing segment
size and remove stale comment.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The POWER8 processor has a Micro Partition Prefetch Engine, which is
a fancy way of saying "has way to store and load contents of L2 or
L2+MRU way of L3 cache". We initiate the storing of the log (list of
addresses) using the logmpp instruction and start restore by writing
to a SPR.
The logmpp instruction takes parameters in a single 64bit register:
- starting address of the table to store log of L2/L2+L3 cache contents
- 32kb for L2
- 128kb for L2+L3
- Aligned relative to maximum size of the table (32kb or 128kb)
- Log control (no-op, L2 only, L2 and L3, abort logout)
We should abort any ongoing logging before initiating one.
To initiate restore, we write to the MPPR SPR. The format of what to write
to the SPR is similar to the logmpp instruction parameter:
- starting address of the table to read from (same alignment requirements)
- table size (no data, until end of table)
- prefetch rate (from fastest possible to slower. about every 8, 16, 24 or
32 cycles)
The idea behind loading and storing the contents of L2/L3 cache is to
reduce memory latency in a system that is frequently swapping vcores on
a physical CPU.
The best case scenario for doing this is when some vcores are doing very
cache heavy workloads. The worst case is when they have about 0 cache hits,
so we just generate needless memory operations.
This implementation just does L2 store/load. In my benchmarks this proves
to be useful.
Benchmark 1:
- 16 core POWER8
- 3x Ubuntu 14.04LTS guests (LE) with 8 VCPUs each
- No split core/SMT
- two guests running sysbench memory test.
sysbench --test=memory --num-threads=8 run
- one guest running apache bench (of default HTML page)
ab -n 490000 -c 400 http://localhost/
This benchmark aims to measure performance of real world application (apache)
where other guests are cache hot with their own workloads. The sysbench memory
benchmark does pointer sized writes to a (small) memory buffer in a loop.
In this benchmark with this patch I can see an improvement both in requests
per second (~5%) and in mean and median response times (again, about 5%).
The spread of minimum and maximum response times were largely unchanged.
benchmark 2:
- Same VM config as benchmark 1
- all three guests running sysbench memory benchmark
This benchmark aims to see if there is a positive or negative affect to this
cache heavy benchmark. Although due to the nature of the benchmark (stores) we
may not see a difference in performance, but rather hopefully an improvement
in consistency of performance (when vcore switched in, don't have to wait
many times for cachelines to be pulled in)
The results of this benchmark are improvements in consistency of performance
rather than performance itself. With this patch, the few outliers in duration
go away and we get more consistent performance in each guest.
benchmark 3:
- same 3 guests and CPU configuration as benchmark 1 and 2.
- two idle guests
- 1 guest running STREAM benchmark
This scenario also saw performance improvement with this patch. On Copy and
Scale workloads from STREAM, I got 5-6% improvement with this patch. For
Add and triad, it was around 10% (or more).
benchmark 4:
- same 3 guests as previous benchmarks
- two guests running sysbench --memory, distinctly different cache heavy
workload
- one guest running STREAM benchmark.
Similar improvements to benchmark 3.
benchmark 5:
- 1 guest, 8 VCPUs, Ubuntu 14.04
- Host configured with split core (SMT8, subcores-per-core=4)
- STREAM benchmark
In this benchmark, we see a 10-20% performance improvement across the board
of STREAM benchmark results with this patch.
Based on preliminary investigation and microbenchmarks
by Prerna Saxena <prerna@linux.vnet.ibm.com>
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
No code changes, just split it out to a function so that with the addition
of micro partition prefetch buffer allocation (in subsequent patch) looks
neater and doesn't require excessive indentation.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Unfortunately, the LPCR got defined as a 32-bit register in the
one_reg interface. This is unfortunate because KVM allows userspace
to control the DPFD (default prefetch depth) field, which is in the
upper 32 bits. The result is that DPFD always get set to 0, which
reduces performance in the guest.
We can't just change KVM_REG_PPC_LPCR to be a 64-bit register ID,
since that would break existing userspace binaries. Instead we define
a new KVM_REG_PPC_LPCR_64 id which is 64-bit. Userspace can still use
the old KVM_REG_PPC_LPCR id, but it now only modifies those fields in
the bottom 32 bits that userspace can modify (ILE, TC and AIL).
If userspace uses the new KVM_REG_PPC_LPCR_64 id, it can modify DPFD
as well.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Graf <agraf@suse.de>
There are a few shared data structures between the host and the guest. Most
of them get registered through the VPA interface.
These data structures are defined to always be in big endian byte order, so
let's make sure we always access them in big endian.
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for the H_SET_MODE hcall. This hcall is a
multiplexer that has several functions, some of which are called
rarely, and some which are potentially called very frequently.
Here we add support for the functions that set the debug registers
CIABR (Completed Instruction Address Breakpoint Register) and
DAWR/DAWRX (Data Address Watchpoint Register and eXtension),
since they could be updated by the guest as often as every context
switch.
This also adds a kvmppc_power8_compatible() function to test to see
if a guest is compatible with POWER8 or not. The CIABR and DAWR/X
only exist on POWER8.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds code to check that when the KVM_CAP_PPC_ENABLE_HCALL
capability is used to enable or disable in-kernel handling of an
hcall, that the hcall is actually implemented by the kernel.
If not an EINVAL error is returned.
This also checks the default-enabled list of hcalls and prints a
warning if any hcall there is not actually implemented.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This provides a way for userspace controls which sPAPR hcalls get
handled in the kernel. Each hcall can be individually enabled or
disabled for in-kernel handling, except for H_RTAS. The exception
for H_RTAS is because userspace can already control whether
individual RTAS functions are handled in-kernel or not via the
KVM_PPC_RTAS_DEFINE_TOKEN ioctl, and because the numeric value for
H_RTAS is out of the normal sequence of hcall numbers.
Hcalls are enabled or disabled using the KVM_ENABLE_CAP ioctl for the
KVM_CAP_PPC_ENABLE_HCALL capability on the file descriptor for the VM.
The args field of the struct kvm_enable_cap specifies the hcall number
in args[0] and the enable/disable flag in args[1]; 0 means disable
in-kernel handling (so that the hcall will always cause an exit to
userspace) and 1 means enable. Enabling or disabling in-kernel
handling of an hcall is effective across the whole VM.
The ability for KVM_ENABLE_CAP to be used on a VM file descriptor
on PowerPC is new, added by this commit. The KVM_CAP_ENABLE_CAP_VM
capability advertises that this ability exists.
When a VM is created, an initial set of hcalls are enabled for
in-kernel handling. The set that is enabled is the set that have
an in-kernel implementation at this point. Any new hcall
implementations from this point onwards should not be added to the
default set without a good reason.
No distinction is made between real-mode and virtual-mode hcall
implementations; the one setting controls them both.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Writing to IC is not allowed in the privileged mode.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
virtual time base register is a per VM, per cpu register that needs
to be saved and restored on vm exit and entry. Writing to VTB is not
allowed in the privileged mode.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[agraf: fix compile error]
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
On recent IBM Power CPUs, while the hashed page table is looked up using
the page size from the segmentation hardware (i.e. the SLB), it is
possible to have the HPT entry indicate a larger page size. Thus for
example it is possible to put a 16MB page in a 64kB segment, but since
the hash lookup is done using a 64kB page size, it may be necessary to
put multiple entries in the HPT for a single 16MB page. This
capability is called mixed page-size segment (MPSS). With MPSS,
there are two relevant page sizes: the base page size, which is the
size used in searching the HPT, and the actual page size, which is the
size indicated in the HPT entry. [ Note that the actual page size is
always >= base page size ].
We use "ibm,segment-page-sizes" device tree node to advertise
the MPSS support to PAPR guest. The penc encoding indicates whether
we support a specific combination of base page size and actual
page size in the same segment. We also use the penc value in the
LP encoding of HPTE entry.
This patch exposes MPSS support to KVM guest by advertising the
feature via "ibm,segment-page-sizes". It also adds the necessary changes
to decode the base page size and the actual page size correctly from the
HPTE entry.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
POWER8 introduces a new facility called the "Event Based Branch" facility.
It contains of a few registers that indicate where a guest should branch to
when a defined event occurs and it's in PR mode.
We don't want to really enable EBB as it will create a big mess with !PR guest
mode while hardware is in PR and we don't really emulate the PMU anyway.
So instead, let's just leave it at emulation of all its registers.
Signed-off-by: Alexander Graf <agraf@suse.de>
