RTC embedded in stm32mp1 SoC is slightly different from stm32h7 one, it
doesn't require to disable backup domain write protection, and rtc_ck
parent clock assignment isn't allowed.
To sum up, stm32mp1 RTC requires 2 clocks, pclk and rtc_ck, and an RTC
alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
According to Devicetree Specification v0.2 document:
"The name of a node should be somewhat generic, reflecting the function
of the device and not its precise programming model."
Do as suggested in the binding example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RTC driver should not be aware of the PWR registers offset and bits
position. Furthermore, we can imagine that Disable Backup Protection (DBP)
relative register and bit mask could change depending on the SoC. So this
patch moves st,syscfg property from single pwrcfg phandle to pwrcfg
phandle/offset/mask triplet.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The ISL12026 is a combination RTC and EEPROM device with I2C
interface. The standard RTC driver interface is provided. The EEPROM
is accessed via the NVMEM interface.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Document the binding for i.MX53 SRTC implemented by rtc-mxc_v2
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Subsystem:
- Fix setting the alarm to the next expiring timer
New driver:
- Mediatek MT7622 RTC
- NXP PCF85363
- Spreadtrum SC27xx PMIC RTC
Drivers:
- Use generic nvmem to expose the Non volatile ram for ds1305, ds1511,
m48t86 and omap
- abx80x: solve possible race condition at probe
- armada38x: support trimming the RTC oscillator
- at91rm9200: fix reading the alarm value at boot
- ds1511: allow waking platform
- m41t80: rework square wave output
- pcf8523: support trimming the RTC oscillator
- pcf8563: fix clock output rate
- pl031: make interrupt optional
- xgene: fix suspend/resume
-----BEGIN PGP SIGNATURE-----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=tRVi
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is nothing scary this cycle, mostly driver fixes and updates.
The core fix has been in for a while and has been tested on multiple
kernel revisions by multiple teams.
Core:
- Fix setting the alarm to the next expiring timer
New drivers:
- Mediatek MT7622 RTC
- NXP PCF85363
- Spreadtrum SC27xx PMIC RTC
Drivers updates:
- Use generic nvmem to expose the Non volatile ram for ds1305,
ds1511, m48t86 and omap
- abx80x: solve possible race condition at probe
- armada38x: support trimming the RTC oscillator
- at91rm9200: fix reading the alarm value at boot
- ds1511: allow waking platform
- m41t80: rework square wave output
- pcf8523: support trimming the RTC oscillator
- pcf8563: fix clock output rate
- pl031: make interrupt optional
- xgene: fix suspend/resume"
* tag 'rtc-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
dt-bindings: rtc: imxdi: Improve the bindings text
rtc: sc27xx: Add Spreadtrum SC27xx PMIC RTC driver
dt-bindings: rtc: Add Spreadtrum SC27xx RTC documentation
rtc: at91rm9200: fix reading alarm value
rtc: at91rm9200: stop calculating yday in at91_rtc_readalarm
rtc: sysfs: Use time64_t variables to set time/alarm
rtc: xgene: mark PM functions as __maybe_unused
rtc: xgene: Fix suspend/resume
rtc: pcf8563: don't alway enable the alarm
rtc: pcf8563: fix output clock rate
rtc: rx8010: Fix for incorrect return value
rtc: rx8010: Specify correct address for RX8010_RESV31
rtc: rx8010: Remove duplicate define
rtc: m41t80: remove unneeded checks from m41t80_sqw_set_rate
rtc: m41t80: avoid i2c read in m41t80_sqw_is_prepared
rtc: m41t80: avoid i2c read in m41t80_sqw_recalc_rate
rtc: m41t80: fix m41t80_sqw_round_rate return value
rtc: m41t80: m41t80_sqw_set_rate should return 0 on success
rtc: add support for NXP PCF85363 real-time clock
rtc: omap: Support scratch registers
...
Improve the bindings text by doing the following changes:
- Remove the i.MX53 reference, as the RTC on i.MX53 is a different hardware
- Add 'clocks' to the list of required properties
- Explain that the optional security violation irq is the second entry
- Use the real unit address and irq numbers for i.MX25
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Juergen Borleis <jbe@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds the binding documentation for Spreadtrum SC27xx series
RTC device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Note that alarms are not currently implemented.
64 bytes of nvmem is supported and exposed in
sysfs (# is the instance number, starting with 0):
/sys/bus/nvmem/devices/pcf85363-#/nvmem
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add device-tree binding for MediaTek SoC based RTC
Cc: devicetree@vger.kernel.org
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that there is documentation for the ds1307 and compatible RTCs, merge
the ds1339 documentation in it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The ST M41T80 family of RTC are not trivial devices, document them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add device tree bindings for the SiRFSoC Real Time Clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add device tree bindings for the ST-Ericsson COH 901 331 Real Time Clock
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Pretty much any node can have a status property, so it doesn't need to
be in examples.
Converted with the following command and removed examples with SoC and
board specific splits:
git grep -l -E 'status.*=.*' Documentation/devicetree/ | xargs sed -i -E '/\sstatus.*=.*"(disabled|ok|okay)/d'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a binding for the RTC on the Realtek RTD119x/RTD129x SoC families.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC can output its 32kHz clock outside of the SoC, for example to clock
a WiFi chip.
Create a new clock that other devices will be able to retrieve, while
maintaining the DT stability by providing a default name for that clock if
clock-output-names doesn't list one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add documentation for DT binding of Goldfish RTC driver. The compatible
string used by OS for binding the driver is "google,goldfish-rtc".
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 8b44f5be20 ("ARM: dts: armada: replace isil,irq2-can-wakeup-machine with wakeup-source property")
removed the last usage of "isil,irq2-can-wakeup-machine" almost
two years ago. So I think we can get rid of supporting this
legacy binding.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch documents support for STM32H7 Real Time Clock.
It introduces a new compatible and rework clock definitions.
On STM32H7 we have a 'pclk' clock for register access, in addition to
the 'rtc_ck' clock.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Gemini RTC is actually a standard IP block from Faraday
Technology called FTRTC010. Rename the bindings, add the
generic compatible string and add definitions for the two
available clocks.
Cc: devicetree@vger.kernel.org
Cc: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Document the binding for the Broadcom STB SoCs wake-up timer node
allowing the system to generate alarms and exit low power states.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the binding documentation for rtc-sh which is an RTC for
SuperH and RZ/A SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver supports the Motorola CPCAP PMIC found on
some of Motorola's mobile phones, such as the Droid 4.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Armada 7K/8K use the same RTC IP than the Armada 38x. However the SOC
integration differs in 2 points:
- MBUS bridge timing initialization
- IRQ configuration at SoC level
Moreover the Armada 7K/8K have an issue preventing to get the interrupt
from alarm 1. This commit allows to use alarm 2 for these A7K/8K but to
still use alarm 1 for the Armada 38x.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are currently two broken bindings descriptions for RTC:
maxim,ds3231.txt
pcf8563.txt
They broke because of a improper RST documentation conversion with
commit 8c27ceff36 ("docs: fix locations of several documents that got
moved") and now reference to a non-existing file:
Documentation/devicetree/bindings/i2c/trivial-admin-guide/devices.rst
However, the original reference to i2c/trivial-devices should have never
been made in the first place.
This change fixes this issue by replacing with correct descriptions.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC controls the input source of the main 32kHz oscillator in the
system, feeding it to the clock unit too.
By default, this is using an internal, very inaccurate (+/- 30%)
oscillator with a divider to make it roughly around 32kHz. This is however
quite impractical for the RTC, since our time will not be tracked properly.
Since this oscillator is an input of the main clock unit, and since that
clock unit will be probed using CLK_OF_DECLARE, we have to use it as well,
leading to a two stage probe: one to enable the clock, the other one to
enable the RTC.
There is also a slight change in the binding that is required (and should
have been from the beginning), since we'll need a phandle to the external
oscillator used on that board. We support the old binding by not allowing
to switch to the external oscillator and only using the internal one (which
was the previous behaviour) in the case where we're missing that phandle.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds documentation of device tree bindings for the STM32 RTC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Document the DryIce security violation interrupt.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system power
controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only
-----BEGIN PGP SIGNATURE-----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=z4SX
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system
power controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only"
* tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (31 commits)
rtc: mcp795: Fix whitespace and indentation.
rtc: mcp795: Prefer using the BIT() macro.
rtc: mcp795: fix month write resetting date to 1.
rtc: mcp795: fix time range difference between linux and RTC chip.
rtc: mcp795: fix bitmask value for leap year (LP).
rtc: mcp795: use bcd2bin/bin2bcd.
rtc: add support for EPSON TOYOCOM RTC-7301SF/DG
rtc: ds1307: Add ACPI support
rtc: imxdi: (trivial) fix a typo
rtc: ds1374: Merge conditional + WARN_ON()
rtc: twl: make driver DT only
rtc: twl: kill static variables
rtc: fix typos in Kconfig
rtc: jz4740: make the driver builtin only
rtc: jz4740: remove unused EXPORT_SYMBOL
Documentation: bindings: fix twl-rtc documentation
rtc: Enable compile testing for Maxim and Samsung drivers
MIPS: jz4740: Remove obsolete code
MIPS: qi_lb60: Probe RTC driver from DT and use it as power controller
MIPS: jz4740: DTS: Probe the jz4740-rtc driver from devicetree
...
This adds support for EPSON TOYOCOM RTC-7301SF/DG which has parallel
interface compatible with SRAM.
This driver supports basic clock, calendar and alarm functionality.
Tested with Microblaze linux running on Artix7 FPGA board with my own
custom IP for RTC-7301.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add interrupts documentation
Fix example and formatting
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This commit adds documentation for the device-tree bindings of the
jz4740-rtc driver, which supports the RTC unit present in the JZ4740 and
JZ4780 SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
... and Epson RX8900 real time clock
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Support configuration of ext_wakeup sources. This patch makes it
possible to enable ext_wakeup and set it's polarity, depending on board
configuration. AM335x's dedicated PMIC (tps65217) uses ext_wakeup to
notify about power-button presses. Handling power-button presses enables
to recover from RTC-only power states correctly.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The number after the '@' symbol should be the SPI chip select
number associated with the ds1390 and it should match the 'reg'
field.
So change it the address to zero, to make it consistent.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These warnings
are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=s+gW
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Rewrite of the unflattening code to avoid recursion and lessen the
stack usage.
- Rewrite of the phandle args parsing code to get rid of the fixed args
size. This is needed for IOMMU code.
- Sync to latest dtc which adds more dts style checking. These
warnings are enabled with "W=1" compiles.
- Tegra documentation updates related to the above warnings.
- A bunch of spelling and other doc fixes.
- Various vendor prefix additions.
* tag 'devicetree-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (52 commits)
devicetree: Add Creative Technology vendor id
gpio: dt-bindings: add ibm,ppc4xx-gpio binding
of/unittest: Remove unnecessary module.h header inclusion
drivers/of: Fix build warning in populate_node()
drivers/of: Fix depth when unflattening devicetree
of: dynamic: changeset prop-update revert fix
drivers/of: Export of_detach_node()
drivers/of: Return allocated memory from of_fdt_unflatten_tree()
drivers/of: Specify parent node in of_fdt_unflatten_tree()
drivers/of: Rename unflatten_dt_node()
drivers/of: Avoid recursively calling unflatten_dt_node()
drivers/of: Split unflatten_dt_node()
of: include errno.h in of_graph.h
of: document refcount incrementation of of_get_cpu_node()
Documentation: dt: soc: fix spelling mistakes
Documentation: dt: power: fix spelling mistake
Documentation: dt: pinctrl: fix spelling mistake
Documentation: dt: opp: fix spelling mistake
Documentation: dt: net: fix spelling mistakes
Documentation: dt: mtd: fix spelling mistake
...
DS1302 is an half-duplex SPI device. The driver respects this fact now.
Pin configurations should be implemented using SPI subsystem.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The S3C binding doc says that the RTC and RTC source clocks are required
but the S3C driver supports different HW IP and only the s3c6410 needs a
source clock.
Fix the binding explaining that the source clock is only needed for the
s3c6410-rtc compatible controller.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Drivers:
- abx80x: handle both XT and RC oscillators, XT failure bit and autocalibration
- m41t80: avoid out of range year values
- rv8803: workaround an i2c HW issue
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PMVI
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull more RTC updates from Alexandre Belloni:
"A second pull request for v4.6 with a few fixesi before -rc1. The new
features for abx80x actually make the RTC behave correctly.
Drivers:
- abx80x: handle both XT and RC oscillators, XT failure bit and
autocalibration
- m41t80: avoid out of range year values
- rv8803: workaround an i2c HW issue"
* tag 'rtc-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: abx80x: handle the oscillator failure bit
rtc: abx80x: handle autocalibration
rtc: rv8803: workaround i2c HW issue
rtc: mcp795: add devicetree support
rtc: asm9260: remove incorrect __init/__exit annotations
rtc: m41t80: avoid out of range year values
rtc: s3c: Don't print an error on probe deferral
rtc: rv3029: stop mentioning rv3029c2
Add device tree support to the rtc-mcp795 driver.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
