Pull input updates from Dmitry Torokhov:
"Two new touchpad drivers - Cypress APA I2C Trackpad and Cypress PS/2
touchpad and a big update to ALPS driver from Kevin Cernekee that adds
support for "Rushmore" touchpads and paves way for adding support for
"Dolphin" touchpads.
There is also a new input driver for Goldfish emulator and also
Android keyreset driver was folded into SysRq code.
A few more drivers were updated with device tree bindings and others
got some small cleanups and fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: cyttsp-spi - remove duplicate MODULE_ALIAS()
Input: tsc2005 - add MODULE_ALIAS
Input: tegra-kbc - require CONFIG_OF, remove platform data
Input: synaptics - initialize pointer emulation usage
Input: MT - do not apply filtering on emulated events
Input: bma150 - make some defines public and fix some comments
Input: bma150 - fix checking pm_runtime_get_sync() return value
Input: ALPS - enable trackstick on Rushmore touchpads
Input: ALPS - add support for "Rushmore" touchpads
Input: ALPS - make the V3 packet field decoder "pluggable"
Input: ALPS - move pixel and bitmap info into alps_data struct
Input: ALPS - fix command mode check
Input: ALPS - rework detection of Pinnacle AGx touchpads
Input: ALPS - move {addr,nibble}_command settings into alps_set_defaults()
Input: ALPS - use function pointers for different protocol handlers
Input: ALPS - rework detection sequence
Input: ALPS - introduce helper function for repeated commands
Input: ALPS - move alps_get_model() down below hw_init code
Input: ALPS - copy "model" info into alps_data struct
Input: ALPS - document the alps.h data structures
...
o goldfish_battery:
This is Android Emulator battery driver. Originally from Google, but
Intel folks reshaped it for mainline;
o pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses AB8500
battery management core;
o qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes;
o restart-poweroff:
A generic driver that implements 'power off by restarting'. The actual
poweroff functionality is implemented through a bootloader, so Linux'
task is just to restart the box. The driver is useful on Buffalo
Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked on
submitting the driver (as well as qnap-poweroff above).
- A lot of fixes for ab8500 drivers. This is a part of efforts of syncing
internal ST-Ericsson development tree with the mainline. Lee Jones @
Linaro worked on compilation and reshaping these series;
- New health properties for the power supplies: "Watchdog timer expire"
and "Safety timer expire";
- As usual, a bunch of fixes/cleanups here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=955B
-----END PGP SIGNATURE-----
Merge tag 'for-v3.9' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Four new drivers:
- goldfish_battery:
This is Android Emulator battery driver. Originally from Google,
but Intel folks reshaped it for mainline
- pm2301_charger:
A new driver for ST-Ericsson 2301 Power Management chip, uses
AB8500 battery management core
- qnap-poweroff:
The driver adds poweroff functionality for QNAP NAS boxes
- restart-poweroff:
A generic driver that implements 'power off by restarting'. The
actual poweroff functionality is implemented through a bootloader,
so Linux' task is just to restart the box. The driver is useful on
Buffalo Linkstation LS-XHL and LS-CHLv2 boards. Andrew Lunn worked
on submitting the driver (as well as qnap-poweroff above).
Additionally:
- A lot of fixes for ab8500 drivers. This is a part of efforts of
syncing internal ST-Ericsson development tree with the mainline.
Lee Jones @ Linaro worked on compilation and reshaping these
series.
- New health properties for the power supplies: "Watchdog timer
expire" and "Safety timer expire"
- As usual, a bunch of fixes/cleanups here and there"
* tag 'for-v3.9' of git://git.infradead.org/battery-2.6: (81 commits)
bq2415x_charger: Add support for offline and 100mA mode
generic-adc-battery: Fix forever loop in gab_remove()
goldfish_battery: Add missing GENERIC_HARDIRQS dependency
da9030_battery: Include notifier.h
bq27x00_battery: Fix reporting battery temperature
power/reset: Remove newly introduced __dev* annotations
lp8727_charger: Small cleanup in naming
ab8500_btemp: Demote initcall sequence
ds2782_battery: Add power_supply_changed() calls for proper uevent support
power: Add battery driver for goldfish emulator
u8500-charger: Delay for USB enumeration
ab8500-bm: Remove individual [charger|btemp|fg|chargalg] pdata structures
ab8500-charger: Do not touch VBUSOVV bits
ab8500-fg: Use correct battery charge full design
pm2301: LPN mode control support
pm2301: Enable vbat low monitoring
ab8500-bm: Flush all work queues before suspending
ab8500-fg: Go to INIT_RECOVERY when charger removed
ab8500-charger: Add support for autopower on AB8505 and AB9540
abx500-chargalg: Add new sysfs interface to get current charge status
...
Fix up fairly straightforward conflicts in the ab8500 driver. But since
it seems to be ARM-specific, I can't even compile-test the result..
Added support for IT8771E, IT8772E, MAX34460, MAX34461, MCP98244,
and ADT7420 to existing drivers.
Added support for additional attributes to various drivers.
Replaced SENSORS_LIMIT with clamp_val; retire SENSORS_LIMIT;
Clean up PMBus code to reduce its size; clean up adt7410 driver.
A couple of minor bug fixes as well as documentation cleanup.
Out-of-tree change: Replace SENSORS_LIMIT with clamp_val in
platform/x86/eeepc-laptop driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=OTEn
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- New drivers for MAX6697 and compatibles and for INA209.
- Added support for IT8771E, IT8772E, MAX34460, MAX34461, MCP98244, and
ADT7420 to existing drivers.
- Added support for additional attributes to various drivers.
- Replaced SENSORS_LIMIT with clamp_val; retire SENSORS_LIMIT;
- Clean up PMBus code to reduce its size; clean up adt7410 driver.
- A couple of minor bug fixes as well as documentation cleanup.
- Out-of-tree change: Replace SENSORS_LIMIT with clamp_val in
platform/x86/eeepc-laptop driver.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (ntc_thermistor): Fix sparse warnings
hwmon: (adt7410) Add device table entry for the adt7420
hwmon: (adt7410) Use I2C_ADDRS helper macro
hwmon: (adt7410) Use the SIMPLE_DEV_PM_OPS helper macro
hwmon: (adt7410) Let suspend/resume depend on CONFIG_PM_SLEEP
hwmon: (adt7410) Clear unwanted bits in the config register
hwmon: (jc42) Add support for MCP98244
hwmon: (pmbus) Clean up for code size reduction
hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461
hwmon: (pmbus) Add support for word status register
hwmon: (pmbus/zl6100) Add support for VMON/VDRV
hwmon: (pmbus) Add function to clear sensor cache
hwmon: (pmbus) Add support for additional voltage sensor
hwmon: (pmbus) Use krealloc to allocate attribute memory
hwmon: (pmbus) Simplify memory allocation for sensor attributes
hwmon: (pmbus) Improve boolean handling
hwmon: (pmbus) Simplify memory allocation for labels and booleans
hwmon: (pmbus) Use dev variable to represent client->dev
hwmon: (pmbus) Fix 'Macros with multiple statements' checkpatch error
hwmon: (pmbus) Drop unnecessary error messages in probe error path
...
- Grabbing of default pinctrl handles from the device core.
These are the hunks hitting drivers/base. All is ACKed by
Greg, after a long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has
been coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500,
AB8505, AB9540 and AB8540.
- Make it possible for hogged pins to enter a sleep mode,
and make it possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to
various pin controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=SQ9W
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the main pinctrl changes for the v3.9 merge window. The
most interesting change by far is how the device core grabs pinctrl
default handles avoiding the need to stick boilerplate into driver
consumers.
- Grabbing of default pinctrl handles from the device core. These
are the hunks hitting drivers/base. All is ACKed by Greg, after a
long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has been
coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500, AB8505, AB9540
and AB8540.
- Make it possible for hogged pins to enter a sleep mode, and make it
possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to various pin
controllers."
* tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (68 commits)
pinctrl: tegra: add clfvs function to Tegra114 support
pinctrl: generic: rename input schmitt disable
pinctrl/pinconfig: add debug interface
pinctrl: samsung: remove duplicated line
ARM: ux500: use real AB8500 IRQ numbers instead of virtual ones
ARM: ux500: remove irq_base property from platform_data
pinctrl/abx500: use direct IRQ defines
pinctrl/abx500: replace IRQ offsets with table read-in values
pinctrl/abx500: move IRQ handling to ab8500-core
pinctrl: exynos5440: remove erroneous __init
pinctrl/abx500: adjust offset for get_mode()
pinctrl/abx500: add Device Tree support
pinctrl/abx500: align GPIO cluster boundaries
pinctrl/abx500: prevent error path from corrupting returning error
pinctrl: sunxi: add of_xlate function
pinctrl/lantiq: fix pin number in ltq_pmx_gpio_request_enable
pinctrl/lantiq: add functionality to falcon_pinconf_dbg_show
pinctrl/lantiq: fix pinconfig parameters
pinctrl/lantiq: one of the boot leds was defined incorrectly
pinctrl/lantiq: only probe available pad controllers
...
Add an output panel driver for LCD panels. Tested with LCD3 cape on
beaglebone.
v1: original
v2: s/of_find_node_by_name()/of_get_child_by_name()/ from Pantelis
Antoniou
v3: add backlight support
v4: rebase to latest of video timing helpers
v5: remove some unneeded fields from panel-info struct, add DT bindings
docs
Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Add output panel driver for i2c encoder slaves.
v1: original
v2: add DT bindings docs, and minor updates for review comments
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
A simple DRM/KMS driver for the TI LCD Controller found in various
smaller TI parts (AM33xx, OMAPL138, etc). This driver uses the
CMA helpers. Currently only the TFP410 DVI encoder is supported
(tested with beaglebone + DVI cape). There are also various LCD
displays, for which support can be added (as I get hw to test on),
and an external i2c HDMI encoder found on some boards.
The display controller supports a single CRTC. And the encoder+
connector are split out into sub-devices. Depending on which LCD
or external encoder is actually present, the appropriate output
module(s) will be loaded.
v1: original
v2: fix fb refcnting and few other cleanups
v3: get +/- vsync/hsync from timings rather than panel-info, add
option DT max-bandwidth field so driver doesn't attempt to
pick a display mode with too high memory bandwidth, and other
small cleanups
v4: remove some unneeded stuff from panel-info struct, properly
set high bits for hfp/hsw/hbp for rev 2, add DT bindings docs
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
* arc-uart platform device now populated dynamically, using
of_platform_populate() - applies to any other device whatsoever.
* uart in turn requires incore arc-intc to be also present in DT
* A irq-domain needs to be instantiated for IRQ requests by DT probed
device (e.g. arc-uart)
TODO: switch over to linear irq domain once all devs have been
transitioned to DT
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Add device tree support for the TI PMIC TPS65090.
The device can be registered through platform or DT.
Add device tree binding document for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds device tree parsing for gpio_ir_recv platform_data and
the mandatory binding documentation. It basically follows what we already
have for e.g. gpio_keys. All required device tree properties are OS
independent but an optional property allows linux specific support for rc
maps.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PAMU caches use the LIODNs to determine which cache lines hold the
entries for the corresponding LIODs. The LIODNs must therefore be
carefully assigned to avoid cache thrashing -- two active LIODs with
LIODNs that put them in the same cache line.
Currently, LIODNs are statically assigned by U-Boot, but this has
limitations. LIODNs are assigned even for devices that may be disabled
or unused by the kernel. Static assignments also do not allow for device
drivers which may know which LIODs can be used simultaneously. In
other words, we really should assign LIODNs dynamically in Linux.
To do that, we need to describe the PAMU device and cache topologies in
the device trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This new property defines the era of the particular SEC version.
The compatible property in device tree "crypto" node has been updated
not to contain SEC era numbers.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode
Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
both the interface as timestamping information doesn't contain port
information.
Constrains
* Reserved VID of One port should not be used in other interface which will
enable switching functionality
* Same VID must not be used in both the interface which will enable switching
functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a very basic I2C host driver for the BCM2835 SoC. Missing
features so far are:
* 10-bit addressing.
* DMA.
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
From Dinh Nguyen, this is a series of patches introducing support for
socfpga hardware (Altera Cyclone5). It also includes a cleanup that
moves some of the ARMv7 cache maintenance functions to a common location,
since three other platforms aready implemented it separately.
* socfpga/hw:
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
Trivial conflict in arch/arm/mach-tegra/headsmp.S.
Signed-off-by: Olof Johansson <olof@lixom.net>
Because the CPU1 start address is different for socfpga-vt and
socfpga-cyclone5, we add code to use the correct CPU1 start addr.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds a simple Device Tree binding for the mvsdio driver, as
well as the necessary documentation for it. Compatibility with non-DT
platforms is preserved, by keeping the platform_data based
initialization.
We introduce a small difference between non-DT and DT platforms: DT
platforms are required to provide a clocks = <...> property, which the
driver uses to get the frequency of the clock that goes to the SDIO
IP. The behaviour on non-DT platforms is kept unchanged: a clock
reference is not mandatory, but the clock frequency must be passed in
the "clock" field of the mvsdio_platform_data structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a very simple driver for the BCM2835 SoC, which is used in the
Raspberry Pi board.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This mxs usbphy is only needs to be on after system boots
up, and software never needs to control it anymore.
Meanwhile, usbphy's parent needs to be notified if usb
is suspend or not. So we design below mxs usbphy usage:
- usbphy1_gate and usbphy2_gate:
Their parents are dummy clock, we only needs to enable
it after system boots up.
- usbphy1 and usbphy2
Usage reserved bit for this clock, in that case, the refcount
will be updated, but without hardware changing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add an entry for imx27-pdk.dtb, so that it can be generated by default.
Also, add an entry into Documentation/devicetree/bindings/arm/fsl.txt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Marvell Kirkwood SoCs have simple cpufreq support in hardware. The
CPU can either use the a high speed cpu clock, or the slower DDR
clock. Add a driver to swap between these two clock sources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixed a typo in referenced file name.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Add documentation for the DT bindings in exynos G2D driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some matrix keypad drivers can support different numbers of rows and
columns. Add a generic binding for these.
Implementation note:
In order to implement this binding in the kernel, we will need to modify
matrix_keypad_() to look up the number of rows and cols in
the keymap. Perhaps this could be done by passing 0 for these parameters?
Many of the parameters can already be set to NULL. Ick.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Marvell Dove SoC has a thermal sensor. Add a driver using the
thermal framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support for Kirkwood 88F6282 and 88F6283 thermal sensor.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Support for loading the Renesas R-Car thermal module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
videomode helpers for of + devicetree stuff, required for new kms drivers
(not the fbdev maintainer).
* tag 'of_videomode_helper' of git://git.pengutronix.de/git/str/linux:
drm_modes: add of_videomode helpers
drm_modes: add videomode helpers
fbmon: add of_videomode helpers
fbmon: add videomode helpers
video: add of helper for display timings/videomode
video: add display_timing and videomode
viafb: rename display_timing to via_display_timing
leds-ns2.txt is a binding for LEDs, not GPIOs. Move the documentation in
with the rest of the LEDs bindings.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.
Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UMMs
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree updates
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
* tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (22 commits)
ARM: dt: tegra30: Rename "smmu" to "iommu"
ARM: dt: tegra20: Rename "gart" to "iommu"
ARM: tegra: move serial clock-frequency attr into the Tegra30 dtsi
ARM: tegra: Add Toradex Iris carrier board DT with T20 512MB COM
ARM: tegra: Add Colibri T20 512MB COM device tree
ARM: tegra: move serial clock-frequency attr into the Tegra20 dtsi
ARM: tegra: harmony: enable keyboard in DT
ARM: tegra: whistler: enable keyboard in DT
ARM: tegra: cardhu: register UARTC
ARM: tegra: seaboard: enable keyboard in DT
ARM: tegra: add DT entry for KBC controller
ARM: tegra: swap cache-/interrupt-ctrlr nodes in DT
ASoC: tegra: add ac97 host controller to device tree
ARM: DT: tegra: Add Tegra30 Beaver board support
ARM: DT: tegra: Add board level compatible properties
ARM: tegra: paz00: enable HDMI port
ARM: tegra: ventana: enable HDMI port
ARM: tegra: seaboard: enable HDMI port
ARM: tegra: trimslice: add gpio-poweroff node to DT
ARM: DT: tegra: Unify the description of Tegra20 boards
...
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8pTe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: USB driver cleanup
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
usb: host: tegra: make use of PHY pointer of HCD
ARM: tegra: Add reset GPIO information to PHY DT node
usb: host: tegra: don't touch EMC clock
usb: add APIs to access host registers from Tegra PHY
USB: PHY: tegra: Get rid of instance number to differentiate PHY type
USB: PHY: tegra: get rid of instance number to differentiate legacy controller
ARM: tegra: add clocks properties to USB PHY nodes
ARM: tegra: add DT nodes for Tegra USB PHY
usb: phy: remove unused APIs from Tegra PHY.
usb: host: tegra: Resetting PORT0 based on information received via DT.
ARM: tegra: Add new DT property to USB node.
usb: phy: use kzalloc to allocate struct tegra_usb_phy
ARM: tegra: remove USB address related macros from iomap.h
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
This adds the capability to retrieve setup data from the device tree
node. The usage of platform data is still available.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert MicBias widgets to supply widget.
On tlv320aic3x, Mic bias power on/off shares the same register bits
with output mic bias voltage. So, when power on mic bias, we need
reclaim it to voltage value.
Provide a new platform data so that the micbias voltage can be sent
according to board requirement. Now since tlv320aic3x codec driver
is DT aware, update dt files and functions to handle this new
"micbias-vg" platform data.
Because of sharing of bits, when enabling the micbias, voltage also
needs to be updated. So use SND_SOC_DAPM_POST_PMU & SND_SOC_DAPM_PRE_PMD
macro to create an event to handle this.
Since micbias is converted to supply widget, updated machine drivers as
well.
This change is runtime tested on da850-evm with audio loopback
(arecord|aplay) for confirmation.
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This new property defines the era of the particular SEC version.
The compatible property in device tree "crypto" node has been updated
not to contain SEC era numbers.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As part of removing generalized dependency, replace <xx> literal fields
in DT compatible field with <52> for am335x platforms.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently cfi_cmdset_0002.c does not support PPB locking of sectors. This
patch adds support for this locking/unlocking mechanism. It is needed on
some platforms, since newer U-Boot versions do support this PPB locking
and protect for example their environment sector(s) this way.
This PPB locking/unlocking will be enabled for all devices supported by
cfi_cmdset_0002 reporting 8 in the CFI word 0x49 (Sector Protect/Unprotect
scheme).
Please note that PPB locking does support sector-by-sector locking. But
the whole chip can only be unlocked together. So unlocking one sector
will automatically unlock all sectors of this device. Because of this
chip limitation, the PPB unlocking function saves the current locking
status of all sectors before unlocking the whole device. After unlocking
the saved locking status is re-configured. This way only the addressed
sectors will be unlocked.
To selectively enable this advanced sector protection mechanism, the
device-tree property "use-advanced-sector-protection" has been created.
To enable support for this locking this property needs to be present in the
flash DT node. E.g.:
nor_flash@0,0 {
compatible = "amd,s29gl256n", "cfi-flash";
bank-width = <2>;
use-advanced-sector-protection;
...
Tested with Spansion S29GL512S10THI and Micron JS28F512M29EWx flash
devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The DT binding for the pwm-leds devices are similar to the gpio-leds type.
LEDs are represented as sub-nodes of the pwm-leds device.
The code for handling the DT boot is based on the code found in the
leds-gpio driver and adapted to use PWMs instead of GPIOs.
To avoid having custom cleanup code in case of DT boot the newly created
devm_of_pwm_get() API is used to get the correct PWM instance.
For usage see:
Documentation/devicetree/bindings/leds/leds-pwm.txt
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In case ELM module available, omap2 NAND driver can opt for hardware
correction method for bit flip errors in NAND flash with BCH. Hence the
detection of ELM module is done through devicetree population of elm_id.
This patch update device tree documentation for gpmc-nand for elm-id
data population.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds device tree bindings for OMAP OneNAND devices.
Tested on an OMAP3 3430 IGEPv2 board.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the documentation for the arch_timer devicetree binding only
lists "arm,armv7-timer".
Add "arm,armv8-timer" to the list of compatible strings.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
some of anatop's regulators(cpu, vddpu and vddsoc) have
register settings about LDO's step time, which will impact
the LDO ramp up speed, need to use set_voltage_time_sel
interface to add necessary delay everytime LDOs' voltage
is increased.
offset 0x170:
bit [24-25]: cpu
bit [26-27]: vddpu
bit [28-29]: vddsoc
field definition:
0'b00: 64 cycles of 24M clock;
0'b01: 128 cycles of 24M clock;
0'b02: 256 cycles of 24M clock;
0'b03: 512 cycles of 24M clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch set converts the Nomadik (mach-nomadik) to
Device Tree and delete the old board files, paving the
road for single zImage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Ip5x
-----END PGP SIGNATURE-----
Merge tag 'nmk-dt-on-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Nomadik Device Tree conversion rebased on ARM SoC cleanup branch
This patch set converts the Nomadik (mach-nomadik) to
Device Tree and delete the old board files, paving the
road for single zImage.
* tag 'nmk-dt-on-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: get rid of <mach/hardware.h>
ARM: nomadik: delete old board files
ARM: nomadik: add I2C devices to the device tree
ARM: nomadik: migrate MMC/SD card support to device tree
ARM: nomadik: convert SMSC91x ethernet to device tree
ARM: nomadik: move GPIO and pinctrl to device tree
ARM: nomadik: add FSMC NAND
ARM: nomadik: move remaining PrimeCells to device tree
ARM: nomadik: move pin maps to cpu file
ARM: nomadik: initial devicetree support
ARM: nomadik: move last custom calls to pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the basic device tree based lookup.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for device based discovery.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the incorrect compatible property value of pinctrl for EXYNOS4 SoCs.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This moves over the MMC/SD card support to the device tree probe
path. The special GPIO to bias the card detect line is kept,
but the pin property is moved to the device tree as part of
the MMC/SD card node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the SMSC91x ethernet controller to use device
tree. The existing solution from the board file, to request the
GPIO triggering the ethernet IRQ from the board file is kept
for the time being, but the GPIO number assignment is moved
over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the FSMC NAND driver and flash partitions to the Nomadik
device tree.
The only compatible string accepted by this driver is currently
"st,spear600-fsmc-nand" which is inappropriate for this system, so
this patch adds the compatible value "stericsson,fsmc-nand" as
well.
Cc: linux-mtd@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support basic device tree boot on the Nomadik. Implement the
support in the cpu file with the intent of deleting the board
files later. At this stage IRQ controllers, system timer,
l2x0 cache, UARTs and thus console boot is fully functional.
Patch out the code adding devices by initcalls for now so
as not to disturb the boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As reset GPIO information is PHY specific detail, adding
it to PHY DT node.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the device tree for the Toradex Iris carrier board used
together with a Colibri T20 512MB COM.
The Iris has the following features, in brackets the current status:
- DVI and VGA output through DVI-I connector (DVI-D enabled and tested)
- LVDS output
- 1 USB host port (enabled and tested)
- 1 USB OTG port (enabled)
- 100 MBit Ethernet (enabled and tested)
- 5 UART ports (2 on 10way headers enabled and tested)
- 1 MicroSD Slot (enabled and tested)
- Audio connectors (enabled, only HP out and Line-in tested)
- i2c RTC
- GPIO connector (enabled, only sparsely tested)
- external i2c bus
- 4 PWM out
- analog in
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the device tree include file for the Toradex Colibri T20
Computer on Module (COM). It's only valid for the 512MB RAM version of
the module, as the 256MB version needs different EMC tables and flash
configuration. To make this clear the suffix -512 was added to the board
compatible string.
The Colibri T20 uses a Tegra20 SoC and has onboard USB Ethernet and AC97
sound.
Still some things like onboard NAND support missing, but should be a
good base for further development.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds support for Tegra30 Beaver board in upstream kernel.
Beaver board is a Tegra30 SoC based development board, it has
following features:
- T30 or T33 SoC (Qual core ARM Cortex A9)
- 2 GB DDR3L
- 16 GB EMMC
- 1 SD slot
- 1 USB Standart A port and 1 USB micro AB port
- PCI-E Gig Ethernet
- Audio input/output
- SATA port
- HDMI output
- UART and JTAG
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The compatible properties of Tegra SoC based boards or machines need
to be documented. This patch adds these board levle compatible
properties into device tree binding document.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add DT nodes for Tegra USB PHY along with related documentation.
Also added a phandle property to controller DT node, for referring
to connected PHY instance.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As Tegra USB host driver is using instance number for resetting
PORT0 twice, adding a new DT property for handling this.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The device tree binding models Tegra30 CAR (Clock And Reset)
as a single monolithic clock provider.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: fixed typo in binding doc]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra20 CAR (Clock And Reset) Controller controls most aspects of
most clocks within Tegra20. The device tree binding models this as a
single monolithic clock provider, which exports many clocks. This reduces
the number of nodes needed in device tree to represent these clocks.
This binding is only useful for Tegra20; the set of clocks that exists on
Tegra30 is sufficiently different to merit its own binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
[pgaikwad: Added mux clk ids and sorted CAR node]
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds a simple Device Tree binding for the mvsdio driver, as
well as the necessary documentation for it. Compatibility with non-DT
platforms is preserved, by keeping the platform_data based
initialization.
We introduce a small difference between non-DT and DT platforms: DT
platforms are required to provide a clocks = <...> property, which the
driver uses to get the frequency of the clock that goes to the SDIO
IP. The behaviour on non-DT platforms is kept unchanged: a clock
reference is not mandatory, but the clock frequency must be passed in
the "clock" field of the mvsdio_platform_data structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a very simple driver for the BCM2835 SoC, which is used in the
Raspberry Pi board.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Mostly clock related updates, most notably the conversion of
i.MX31 to a DT based lookup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bWtE
-----END PGP SIGNATURE-----
Merge tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for next
Mostly clock related updates, most notably the conversion of
i.MX31 to a DT based lookup.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: clk-imx35: Fix build warnings with W=1
ARM: imx27: add a clock gate to activate SPLL clock
ARM: mx31: Replace clk_register_clkdev with clock DT lookup
ARM: clk-imx31: Add dummy clock
ARM: Let CONFIG_MACH_IMX31_DT be built by default
Signed-off-by: Olof Johansson <olof@lixom.net>
From Barry Song, this adds support for a new SoC from CSR; marco. It's
SMP, uses GIC instead of VIC and in general needs a bit of rework of
the platform code for setup, which this branch contains.
* 'marco-timer-cleanup-rebase' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel:
ARM: PRIMA2: provide two DEBUG_LL ports for prima2 and marco
ARM: PRIMA2: add new SiRFmarco SMP SoC infrastructures
ARM: PRIMA2: irq: make prima2 irq can work even we enable GIC for Marco
ARM: PRIMA2: rtciobg: it is also compatible with marco
ARM: PRIMA2: rstc: enable the support for Marco
ARM: PRIMA2: mv timer to timer-prima2 as we will add timer-marco
ARM: PRIMA2: initialize l2x0 according to mach from DT
ARM: PRIMA2: enable AUTO_ZRELADDR for SIRF in Kconfig
ARM: PRIMA2: add CSR SiRFmarco device tree .dts
Signed-off-by: Olof Johansson <olof@lixom.net>
