dw_mci_exynos_resume_noirq() performs DWMMC register access without
ensuring that respective clocks are enabled. This might cause external
abort on some systems (observed on Exynos5433 based boards). Fix this
by forcing a PM runtime active state before register access. Using
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS allows also to cleanup conditional code
a bit.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci get_max_clock callback is set to sdhci_pltfm_clk_get_max_clock
and tegra_sdhci_get_max_clock is removed. It appears that the
shdci-tegra specific callback was originally introduced due to the
requirement that the host clock has to be twice the bus clock on DDR50
mode. As far as I can tell the only effect the removal has on DDR50 mode
is in cases where the parent clock is unable to supply the requested
clock rate, causing the DDR50 mode to run at a lower frequency.
Currently the DDR50 mode isn't enabled on any of the SoCs and would also
require configuring the SDHCI clock divider register to function
properly.
The problem with tegra_sdhci_get_max_clock is that it divides the clock
rate by two and thus artificially limits the maximum frequency of faster
signaling modes which don't have the host-bus frequency ratio requirement
of DDR50 such as SDR104 and HS200. Furthermore, the call to
clk_round_rate() may return an error which isn't handled by
tegra_sdhci_get_max_clock.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
R1_STATUS(x) now is only used by ioctl_rpmb_card_status_poll(),
which checks all bits as possible. But according to the spec,
bit 17 and bit 18 should be ignored, as well bit 14 which is
reserved(must be set to 0) quoting from the spec and these rule
apply to all places checking the device status. So change
its checking from 0xFFFFE000 to 0xFFF9A000.
As a bonus, we reuse it for mmc_do_erase() as well as
mmc_switch_status_error().
(1) Currently mmc_switch_status_error() doesn't check bit 25, but
it means device is locked but not unlocked by CMD42 prior to any
operations which need check busy, which is also not allowed.
(2) mmc_do_erase() also forgot to to check bit 15, WP_ERASE_SKIP.
The spec says "Only partial address space was erased due to existing
write protected blocks.", which obviously means we should fail this I/O.
Otherwise, the partial erased data stored in nonvalatile flash violates
the data integrity from the view of I/O owner, which probably confuse
it when further used.
So reusing R1_STATUS for them not only improve the readability but also
slove real problems.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fixes: ad93220de7 ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When mmc host controller enters suspend state, the clocks are
disabled, but irqs are not. For some reason the irqchip emits
false interrupts, which causes system lock loop.
Debug log is:
...
sunxi-mmc 1c11000.mmc: setting clk to 52000000, rounded 51200000
sunxi-mmc 1c11000.mmc: enabling the clock
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 6(80000146) arg 3210101 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
sunxi-mmc 1c11000.mmc: cmd 13(8000014d) arg 10000 ie 0x0000bbc6 len 0
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00000004 idi 00000000
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 AGND3R 14.6 GiB
mmcblk1boot0: mmc1:0001 AGND3R partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 AGND3R partition 2 4.00 MiB
sunxi-mmc 1c11000.mmc: cmd 18(80003352) arg 0 ie 0x0000fbc2 len 409
sunxi-mmc 1c11000.mmc: irq: rq (ptrval) mi 00004000 idi 00000002
mmcblk1: p1
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
sunxi-mmc 1c11000.mmc: irq: rq (null) mi 00000000 idi 00000000
and so on...
This issue apears on eMMC cards, routed on MMC2 slot. The patch is
tested with A20-OLinuXino-MICRO/LIME/LIME2 boards.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Card write threshold control is supposed to be set since controller
version 2.80a for data write in HS400 mode and data read in
HS200/HS400/SDR104 mode. However the current code returns without
configuring it in the case of data writing in HS400 mode.
Meanwhile the patch fixes that the current code goes to
'disable' when doing data reading in HS400 mode.
Fixes: 7e4bf1bc95 ("mmc: dw_mmc: add the card write threshold for HS400 mode")
Signed-off-by: Qing Xia <xiaqing17@hisilicon.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bfd694d5e2 ("mmc: core: Add tunable delay
before detecting card after card is inserted") adds
"u32 cd_debounce_delay_ms" to the last of mmc_gpio
struct and cause "char cd_label[0]" NOT work as string
pointer of card detect label, when "cat /proc/interrupts",
the devname for card detect gpio is incorrect as below:
144: 0 gpio-mxc 22 Edge ▒
161: 0 gpio-mxc 7 Edge ▒
Move the cd_label field down to fix this, and drop the
zero from the array size to prevent future similar bugs,
the result is correct as below:
144: 0 gpio-mxc 22 Edge 2198000.mmc cd
161: 0 gpio-mxc 7 Edge 2190000.mmc cd
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card after card is inserted")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is fixes an issue that the SDHI_INTERNAL_DMAC_RX_IN_USE
flag cannot be cleared because tmio_mmc_core sets the host->data
to NULL before the tmio_mmc_core calls tmio_mmc_abort_dma().
So, this patch clears the SDHI_INTERNAL_DMAC_RX_IN_USE in
the renesas_sdhi_internal_dmac_abort_dma() anyway. This doesn't
cause any side effects.
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes an issue that lacks the dma_unmap_sg() calling in
the error patch of renesas_sdhi_internal_dmac_start_dma().
Fixes: 0cbc94daa5 ("mmc: renesas_sdhi_internal_dmac: limit DMA RX for old SoCs")
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching
-----BEGIN PGP SIGNATURE-----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=MwCT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Decrease polling rate for erase/trim/discard
- Allow non-sleeping GPIOs for card detect
- Improve mmc block removal path
- Enable support for mmc_sw_reset() for SDIO cards
- Add mmc_sw_reset() to allow users to do a soft reset of the card
- Allow power delay to be tunable via DT
- Allow card detect debounce delay to be tunable via DT
- Enable new quirk to limit clock rate for Marvell 8887 chip
- Don't show eMMC RPMB and BOOT areas in /proc/partitions
- Add capability to avoid 3.3V signaling for fragile HWs
MMC host:
- Improve/fixup support for handle highmem pages
- Remove depends on HAS_DMA in case of platform dependency
- mvsdio: Enable support for erase/trim/discard
- rtsx_usb: Enable support for erase/trim/discard
- renesas_sdhi: Fix WP logic regressions
- renesas_sdhi: Add r8a77965 support
- renesas_sdhi: Add R8A77980 to whitelist
- meson: Add optional support for device reset
- meson: Add support for the Meson-AXG platform
- dw_mmc: Add new driver for BlueField DW variant
- mediatek: Add support for 64G DRAM DMA
- sunxi: Deploy runtime PM support
- jz4740: Add support for JZ4780
- jz4740: Enable support for DT based platforms
- sdhci: Various improvement to timeout handling
- sdhci: Disable support for HS200/HS400/UHS when no 1.8V support
- sdhci-omap: Add support for controller in k2g SoC
- sdhci-omap: Add workarounds for a couple of Erratas
- sdhci-omap: Enable support for generic sdhci DT properties
- sdhci-cadence: Re-send tune request to deal with errata
- sdhci-pci: Fix 3.3V voltage switch for some BYT-based Intel controllers
- sdhci-pci: Avoid 3.3V signaling on some NI 904x
- sdhci-esdhc-imx: Use watermark levels for PIO access
- sdhci-msm: Improve card detection handling
- sdhci-msm: Add support voltage pad switching"
* tag 'mmc-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (104 commits)
mmc: renesas_sdhi: really fix WP logic regressions
mmc: mvsdio: Enable MMC_CAP_ERASE
mmc: mvsdio: Respect card busy time out from mmc core
mmc: sdhci-msm: Remove NO_CARD_NO_RESET quirk
mmc: sunxi: Use ifdef rather than __maybe_unused
mmc: mxmmc: Use ifdef rather than __maybe_unused
mmc: mxmmc: include linux/highmem.h
mmc: sunxi: mark PM functions as __maybe_unused
mmc: Throttle calls to MMC_SEND_STATUS during mmc_do_erase()
mmc: au1xmmc: handle highmem pages
mmc: Allow non-sleeping GPIO cd
mmc: sdhci-*: Don't emit error msg if sdhci_add_host() fails
mmc: sd: Define name for default speed dtr
mmc: core: Move calls to ->prepare_hs400_tuning() closer to mmc code
mmc: sdhci-xenon: use match_string() helper
mmc: wbsd: handle highmem pages
mmc: ushc: handle highmem pages
mmc: mxcmmc: handle highmem pages
mmc: atmel-mci: use sg_copy_{from,to}_buffer
mmc: android-goldfish: use sg_copy_{from,to}_buffer
...
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJbFRzjAAoJEILEb/54YlRxREQQAKD7IjnLA86ZDkmwiwzFa9Cz
OJ0qlKAcMZGjeWH6LYq7lqWtaJ5PcFkBwNB4sRyKFdGPQOX3Ph8ZzILm2j8hhma4
Azn9632P6CoYHABa8Vof+A1BZ/j0aWtvtJEfqXhtF6rAYyWQlF0UmOIRsMs+54a+
Z/w4WuLaX8qYq3JlR60TogNtTIbdUjkjfvxMGrE9OSQ8n4oEhqoF/v0WoTHYLpWw
fu81M378axOu0Sgq1ZQ8GPUdblUqIO97iWwF7k2YUl7D9n5dm4wOhXDz3CLI8Cdb
RkoFFdp8bJIthbc5desKY2XFU1ClY8lxEVMXewFzTGwWMw0OyWgQP0/ZiG+Mujq3
CSbstg8GGpbwQoWU+VrluYa0FtqofV2UaGk1gOuPaojMqaIchRU4Nmbd2U6naNwp
XN7A1DzrOVGEt0ny8ztKH2Oqmj+NOCcRsChlYzdhLQ1wlqG54iCGwAML2ZJF9/Nw
0Sx8hm6eyWLzjSa0L384Msb+v5oqCoac66gPHCl2x7W+3F+jmqx1KbmkI2SRNUAL
7CS9lcImpvC4uZB54Aqya104vfqHiDse7WP0GrKqOmNVucD7hYCPiq/pycLwez+b
V3zLyvly8PsuBIa4AOQGGiK45HGpaKuB4TkRqRyFO0Fb5uL1M+Ld6kJiWlacl4az
STEUjY/90SRQvX3ocGyB
=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
This reverts commit e060d376cc ("mmc: renesas_sdhi: fix WP detection")
and adds some code to really fix the regressions.
It was missed so far that Renesas R-Car instantiations of SDHI chose to
disable internal WP and used the existence of "wp-gpios" to en/disable
WP at all.
With the first refactoring by Yamada-san with commit 2ad1db059b ("mmc:
renesas_sdhi: use MMC_CAP2_NO_WRITE_PROTECT instead of TMIO own flag"),
WP was always disabled even when GPIOs were present. With Wolfram's
first fix which gets now reverted, GPIOs were honored. But when not
available, the fallback was to internal WP and not to disabled WP. This
caused wrong WP status on uSD card slots.
Restore the old behaviour now. By default, WP is disabled. When a GPIO
is found, the GPIO re-enables WP. We will think about possible better
ways to handle this in the future.
Tested on a previously regressing Renesas Lager board (H2) and a still
working Renesas Salvator-X board (M3-W).
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
There is no obvious reasons to why mvsdio shouldn't be able to support
erase/trim/discard operations, hence let's set MMC_CAP_ERASE for it.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Instead of using a hardcoded timeout of 5 * HZ jiffies, let's respect the
command busy timeout provided by the mmc core. This make the used timeout
more reliable.
Cc: Damien Thebault <damien.thebault@vitec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Damien Thebault <damien.thebault@vitec.com>
Now we have a proper implementation for the power irq handling and this
quirk is not needed anymore. In fact, it is causing card detection delays
on apq8096 platforms and the following error is displayed:
sdhci_msm 74a4900.sdhci: mmc0: pwr_irq for req: (4) timed out
The quirk is forcing the controller to retain 1.8V signalling on the slot
even when a new card is inserted, which is not correct. The proper behavior
would be to reset the controller in order to start with 3.3V signaling.
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Suggested-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To be consistent with code in other mmc host drivers, convert to check the
correct PM config #ifdef in favor of using __maybe_unused.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By completing the request entirely in the driver we can remove the
BLK_EH_HANDLED return value and thus the split responsibility between the
driver and the block layer that has been causing trouble.
[While this keeps existing behavior it seems to mismatch the comment,
maintainers please chime in!]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The highmem conversion caused a build error in some configurations:
drivers/mmc/host/mxcmmc.c: In function 'mxcmci_transfer_data':
drivers/mmc/host/mxcmmc.c:622:10: error: implicit declaration of function 'kmap_atomic'; did you mean 'in_atomic'? [-Werror=implicit-function-declaration]
This includes the correct header file.
Fixes: b189e7589f ("mmc: mxcmmc: handle highmem pages")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newly added runtime-pm functions cause a harmless warning
when CONFIG_PM is disabled:
drivers/mmc/host/sunxi-mmc.c:1452:12: error: 'sunxi_mmc_runtime_suspend' defined but not used [-Werror=unused-function]
static int sunxi_mmc_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/mmc/host/sunxi-mmc.c:1435:12: error: 'sunxi_mmc_runtime_resume' defined but not used [-Werror=unused-function]
static int sunxi_mmc_runtime_resume(struct device *dev)
This marks them as __maybe_unused to shut up the warning.
Fixes: 9a8e1e8cc2 ("mmc: sunxi: Add runtime_pm support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This drastically reduces the rate at which the MMC_SEND_STATUS cmd polls
for completion of the MMC Erase operation. The patch does this by adding
a backoff sleep that starts by sleeping for short intervals (128-256us),
and ramps up to sleeping for 32-64ms.
Even on very quickly completing erase operations, the loop iterates a few
times, so not too much extra latency is added to these commands.
For long running discard operarations, like a full-device secure discard,
this change drops the interrupt rates on my single-core NXP I.MX6UL from
45000/s to about 20/s, and greatly improves system responsiveness.
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmap_atomic to map the scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO card detect state. This allows users with GPIOs that
never sleep to avoid a warning when certain quirks are present.
The sdhci controller has an SDHCI_QUIRK_NO_CARD_NO_RESET, which
indicates that a controller will not reset properly if no card is
inserted. With this quirk enabled, mmc_get_cd_gpio is called in
several places with a spinlock held and interrupts disabled.
gpiod_get_raw_value_cansleep is not happy with this situation,
and throws out a warning.
For boards that a) use controllers that have this quirk, and b) wire
card detect up to a GPIO that doesn't sleep, this is a spurious warning.
This change silences that warning, at the cost of pushing this problem
down to users that have sleeping GPIOs and controllers with this quirk.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I noticed below error msg with sdhci-pxav3 on some berlin platforms:
[.....] sdhci-pxav3 f7ab0000.sdhci failed to add host
It is due to getting related vmmc or vqmmc regulator returns
-EPROBE_DEFER. It doesn't matter at all but it's confusing.
>From another side, if driver probing fails and the error number isn't
-EPROBE_DEFER, the core will tell us something as below:
[.....] sdhci-pxav3: probe of f7ab0000.sdhci failed with error -EXX
So it's not necessary to emit error msg if sdhci_add_host() fails. And
some other sdhci host drivers also have this issue, let's fix them
together.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the calls to ->prepare_hs400_tuning(), from mmc_retune() into
mmc_hs400_to_hs200(), as it better belongs there, rather than being generic
to all type of cards.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use sg_copy_{from,to}_buffer to bounce buffer and kmap_atomic to map the
scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pass the scatterlist on to the USB subsystem instead of expecting a
kernel virtual address.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use kmap_atomic to map the scatterlist entry before using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This handles highmem pages, and also cleans up the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This handles highmem pages, and also cleans up the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's pointless to switch and trace partition type if the current
selected device partition is the same with that one. Moreover, cycled
claiming host associated with mmc_blk_part_switch() could make
mmc_blk_remove() end up waiting for grabbing the context if it's
occupied, which lead requests could still hit the low-level drivers,
if an asynchronous unbind for host drivers happened, as the card hasn't
been set removed in the remove path.
So a simple dd in background:
dd if=/dev/mmcblk0 of=/dev/null bs=512k count=100000 &
and doing unbind then:
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/unbind
could make the console stuck for quite a while depending on the
numbers of requests.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_QUIRK2_HOST_OFF_CARD_ON is needed for the driver to
properly reset the host controller (reset all) on initialization
after exiting deep sleep.
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Fixes: c833e92bbb ("mmc: sdhci-iproc: support standard byte register accesses")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.
Fixes: b580c52d58 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove hard coded mmc cap 1.8v from platform data as it is board specific.
The 1.8v DDR mmc caps can be enabled using DTS property for those
boards that support it.
Fixes: b17b4ab8ce ("mmc: sdhci-iproc: define MMC caps in platform data")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 97548575be ("mmc: block: Convert RPMB to a character device") a
new function `mmc_rpmb_ioctl` was added. The final return is simply
returning a value of `0` instead of propagating the correct return code.
Discovered during a compilation with W=1, silence the following gcc warning
drivers/mmc/core/block.c:2470:6: warning: variable ‘ret’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Trigger the reset line of the mmc controller while probing, if available.
The reset should be optional for now, at least until all related DT nodes
have the reset property.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit adds extension to the dw_mmc driver for Mellanox BlueField
SoC. It updates the UHS_REG_EXT register to bring up the eMMC card on
this SoC.
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aef ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.
However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.
With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Switch everyone to blk_get_request_flags, and then rename
blk_get_request_flags to blk_get_request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A redundant return statement is removed from
tegra_sdhci_set_uhs_signaling(). The function returns void and the
return does not affect the control flow of the function.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of using a fixed 3s timeout for commands with R1B responses,
convert to use the per request calculated busy timeout from the mmc core.
This is needed to cope with requests that requires longer timeout, for
example erase/discard commands.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Instead of having to return -EINVAL when requested to send SDIO specific
commands, let's set MMC_CAP2_NO_SDIO as it completely prevents them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Let's implement the ->sw_reset() bus ops to allow SDIO func drivers, in
particular, to make a SW reset without doing a full power cycle of the SDIO
card.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().
Make the function internally available to the mmc core, as to allow the
following changes to make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.
However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.
To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.
The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_sdio_init_card() function has a couple of callers. In the
re-initialization cases, some additional reset commands are issued before
mmc_sdio_init_card() is called. As these additional reset commands are the
same, let's move these into a new static function, mmc_sdio_reinit_card()
and call mmc_sdio_init_card() from there. In this way we avoid the open
coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Allow to use tunable delay before detecting card after card is inserted,
which either comes from firmware node, or comes from debounce value
passed on to mmc_gpiod_request_cd(). If the platform doesn't support
debounce, then we fall back to use the debounce period as the delay,
otherwise, it behaves the same as before that a HW debounce(if set) plus
a 200ms hardcode delay before detecting the card.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 8d20b2eae6 ("mmc: sdhci_omap: Add support to set
IODELAY values") stored IODelay values for all MM/SD modes
in pinctrl_state structure member of sdhci_omap_host. However for
DDR mode it gets IODelay values only for 1.8v DDR mode. Since some of
the platforms which uses sdhci-omap has IO lines connected to 3.3v,
get IODelay values for 3.3v DDR mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add sdhci_omap_enable_sdio_irq to set CTPL and CLKEXTFREE bits in
MMCHS_CON register required to detect asynchronous card interrupt
on DAT[1].
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the new compatible added specifically to support
k2g's MMC/SD controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i834 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions the maximum
obtainable timeout through MMC host controller is 700ms. And for
commands taking longer than 700ms, hardware timeout should be
disabled and software timeout should be used.
The workaround for Errata i834 can be achieved by adding
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT quirk in sdhci-omap.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a 10 second timeout to catch devices that stop responding.
In the case of quirk SDHCI_QUIRK2_DISABLE_HW_TIMEOUT, instead of
programming 10 second arbitrary value, calculate the total time it would
take for the entire transfer to happen and program the timeout value
accordingly.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out the target_timeout calculation so it can be re-used.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to disable HW timeout if the requested timeout is more than the
maximum obtainable timeout.
Also, if the quirk is set and ->get_max_timeout_count() is not implemented,
max_busy_timeout is set to zero.
Based-on-patch-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller in a SoC might support HS200/HS400 (indicated
using mmc-hs200-1_8v/mmc-hs400-1_8v dt property), but if the board is
modeled such that the IO lines are not connected to 1.8v then
HS200/HS400 cannot be supported. Disable HS200/HS400 if the board
does not have 1.8v connected to the IO lines. Also Disable DDR/UHS in 1.8v
if the IO lines are not connected to 1.8v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Invoke sdhci_get_of_property defined in sdhci-pltfm.c to read
sdhci specific properties from dt node.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i843 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
PG 1.0/1.1 silicon has limitations w.r.t frequencies at which MMC1/2/3
can operate.
Use soc_device_match() to identify rev 1.0/1.1 silicon and
override mmc->f_max according to the errata workaround.
"max-frequency" dt property cannot be used since the device
tree is added for rev 2.0 silicon.
soc_device_match() is also used in order to get the IODelay values
for rev 1.0/1.1 silicon.
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci can directly get ADMA capability from MMCHS_CAPA register.
Remove explicitly setting ADMA here as some instances might not have
ADMA enabled. (sdhci_read_caps() is also removed from here since
sdhci_setup_host() invokes it).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_omap_config_iodelay_pinctrl_state() requires caps and caps2 to be
initialized (speed mode capabilities like UHS/HS200) before it is
invoked. While mmc_of_parse() initializes caps/caps2 if capabilities is
populated in device tree, it will remain uninitialized for capabilities
obtained from SDHCI_CAPABILITIES register.
Fix sdhci_omap_config_iodelay_pinctrl_state() to be used even while
getting the capabilities from SDHCI_CAPABILITIES register by invoking
sdhci_setup_host() before sdhci_omap_config_iodelay_pinctrl_state().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Remove the local_irq_save() invocation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While performing R/W access in PIO mode, the common SDHCI driver checks
the buffer ready status once per whole block processing. That is, after
getting an appropriate interrupt, or checking an appropriate status bit,
the driver makes buffer accesses for the whole block size (e.g. 128 reads
for 512 bytes block). This is done in accordance with SD Host Controller
Specification.
At the same time, the Ultra Secured Digital Host Controller (uSDHC), used
in i.MX6 (and, probably, earlier i.MX series too), uses a separate
Watermark Levels register, controlling the amount of data or space
available when raising status bit or interrupt. For default watermark
setting of 16 words, the controller expects (and guarantees) no more
than 16 buffer accesses after raising buffer ready status bit and
generating an appropriate interrupt. If the driver tries to access the
whole block size, it will get incorrect data at the end, and a new
interrupt will appear later, when the driver already doesn't expect it.
This happens sometimes, more likely on low frequencies, e.g. when
reading EXT_CSD at MMC card initialization phase
(which makes that initialization fail).
Such behavior of i.MX uSDHC seems to be non-compliant
to SDHCI Specification, but this is the way it works now.
In order not to rewrite the SDHCI driver PIO mode access logic,
the IMX specific driver can just set the watermark level to default
block size (128 words or 512 bytes), so that the controller behavior
will be consistent to generic specification. This patch does this
for PIO mode accesses only, restoring default values for DMA accesses
to avoid any possible side effects from performance point of view.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PADs for SD card are dual-voltage that support 3v/1.8v. Those PADs
have a control signal (io_pad_pwr_switch/mode18 ) that indicates
whether the PAD works in 3v or 1.8v.
SDHC core on msm platforms should have IO_PAD_PWR_SWITCH bit set/unset
based on actual voltage used for IO lines. So when power irq is
triggered for io high or io low, the driver should check the voltages
supported and set the pad accordingly.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During probe check whether the vdd-io regulator of sdhc platform device
can support 1.8V and 3V and store this information as a capability of
platform device.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I've successfully tested eMMC on R8A77980/Condor. R8A77980 has a single
SDHI core anyway, so can't be a subject of the known RX DMA errata...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the code block inside the for loop will never execute more than
once, because the function returns immediately after the first iteration,
hence the execution of the code at the second iteration is structurally
dead and, code at line 281: return 0; is never reached.
Fix this by checking _ret_ before return.
Addresses-Coverity-ID: 1468009 ("Logically dead code")
Addresses-Coverity-ID: 1468002 ("Structurally dead code")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call msdc_drv_probe() is to match an entry in
msdc_of_ids[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix 3.3V voltage switch for some BYT-based Intel controllers by making use
of the ACPI DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The WARN can never trigger because we limited the max_seg number in
renesas_sdhi_of_data already. Remove it and update the comment.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Whitelisting every ES version does not scale. So, we whitelist whole
SoCs independent of ES version. If we need specific handling for an ES
version, we put it to the front, so it will be matched first.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sometimes sg->offset is not used for buffer addresses allocated by
dma_map_sg(), so alignment checks should be done on the allocated buffer
addresses. Delete the alignment check for sg->offset that is done before
dma_map_sg(). Instead, it performs the alignment check for
sg->dma_address after dma_map_sg().
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: broke this commit in two and tidied small style issue]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of directly accessing the members of struct scatterlist use the
helpers mmc_get_dma_dir() and sg_dma_address() in
renesas_sdhi_internal_dmac_start_dma(). Based on previous work by
Masaharu Hayakawa.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[rebased to mmc/next]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some NI 904x devices, using 3.3V signaling for extended periods of
time will physically damage the pads connected to the SDHC, eventually
causing complete failure of the controller. To work around this,
require that we avoid 3.3V signaling.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our set_ios hook is, when the card is power up or down, either doing a full
init or put our controller back into a reset mode.
Since we're also doing that in our runtime_pm hooks, and at possibly much
more often, we can drop it from the set_ios, and either rely on our
runtime_pm hooks or our probe to do it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far, even if our card was not in use, we didn't shut down our MMC
controller, which meant that it was still active and clocking the bus.
While this obviously means that we could save some power there, it also
creates issues when it comes to EMC control since we'll have a perfect peak
at the card clock rate.
Let's implement runtime_pm with autosuspend so that we will shut down the
controller when it's not been in use for quite some time.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the card setup
to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the clock setup
to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to improve readibility and reusability, let's move the bus width
setup to a small function called by our .set_ios hook.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the other functions in the driver take a struct sunxi_mmc_host pointer.
Let's make it consistent.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
