This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).
In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.
The current patch will clear the previous bus mode and apply the new
mode setting.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_sd_init_uhs_card function sets the driver type, current limit
and bus speed mode on card as well as on host controller side.
Currently bus speed mode is set by sending CMD6 to card and
immediately setting the timing mode in host controller. But
then before initiating tuning sequence, it also tries to set
current limit by sending CMD6 to card which results in data
timeout errors in controller if bus speed mode is SDR50/SDR104 mode.
So basically bus speed mode should be set only after current limit
is set in the card and immediately after setting the bus speed mode,
tuning sequence should be initiated.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This corrects a logic error that I introduced in
"mmc: sdhi: Add write16_hook"
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.
To prevent this from happening we use system_nrt_wq instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have seen at least two different races when clock gating kicks in in a
middle of ios structure update.
First one happens when ios->clock is changed outside of aggressive clock
gating framework, for example via mmc_set_clock(). The race might happen
when we run following code:
mmc_set_ios():
...
if (ios->clock > 0)
mmc_set_ungated(host);
Now if gating kicks in right after the condition check we end up setting
host->clk_gated to false even though we have just gated the clock. Next
time a request is started we try to ungate and restore the clock in
mmc_host_clk_hold(). However since we have host->clk_gated set to false the
original clock is not restored.
This eventually will cause the host controller to hang since its clock is
disabled while we are trying to issue a request. For example on Intel
Medfield platform we see:
[ 13.818610] mmc2: Timeout waiting for hardware interrupt.
[ 13.818698] sdhci: =========== REGISTER DUMP (mmc2)===========
[ 13.818753] sdhci: Sys addr: 0x00000000 | Version: 0x00008901
[ 13.818804] sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 13.818853] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 13.818903] sdhci: Present: 0x1fff0000 | Host ctl: 0x00000001
[ 13.818951] sdhci: Power: 0x0000000d | Blk gap: 0x00000000
[ 13.819000] sdhci: Wake-up: 0x00000000 | Clock: 0x00000000
[ 13.819049] sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 13.819098] sdhci: Int enab: 0x00ff00c3 | Sig enab: 0x00ff00c3
[ 13.819147] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.819196] sdhci: Caps: 0x6bee32b2 | Caps_1: 0x00000000
[ 13.819245] sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 13.819292] sdhci: Host ctl2: 0x00000000
[ 13.819331] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[ 13.819377] sdhci: ===========================================
[ 13.919605] mmc2: Reset 0x2 never completed.
and it never recovers.
Second race might happen while running mmc_power_off():
static void mmc_power_off(struct mmc_host *host)
{
host->ios.clock = 0;
host->ios.vdd = 0;
[ clock gating kicks in here ]
/*
* Reset ocr mask to be the highest possible voltage supported for
* this mmc host. This value will be used at next power up.
*/
host->ocr = 1 << (fls(host->ocr_avail) - 1);
if (!mmc_host_is_spi(host)) {
host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
host->ios.chip_select = MMC_CS_DONTCARE;
}
host->ios.power_mode = MMC_POWER_OFF;
host->ios.bus_width = MMC_BUS_WIDTH_1;
host->ios.timing = MMC_TIMING_LEGACY;
mmc_set_ios(host);
}
If the clock gating worker kicks in while we are only partially updated the
ios structure the host controller gets incomplete ios and might not work as
supposed. Again on Intel Medfield platform we get:
[ 4.185349] kernel BUG at drivers/mmc/host/sdhci.c:1155!
[ 4.185422] invalid opcode: 0000 [#1] PREEMPT SMP
[ 4.185509] Modules linked in:
[ 4.185565]
[ 4.185608] Pid: 4, comm: kworker/0:0 Not tainted 3.0.0+ #240 Intel Corporation Medfield/iCDKA
[ 4.185742] EIP: 0060:[<c136364e>] EFLAGS: 00010083 CPU: 0
[ 4.185827] EIP is at sdhci_set_power+0x3e/0xd0
[ 4.185891] EAX: f5ff98e0 EBX: f5ff98e0 ECX: 00000000 EDX: 00000001
[ 4.185970] ESI: f5ff977c EDI: f5ff9904 EBP: f644fe98 ESP: f644fe94
[ 4.186049] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 4.186125] Process kworker/0:0 (pid: 4, ti=f644e000 task=f644c0e0 task.ti=f644e000)
[ 4.186219] Stack:
[ 4.186257] f5ff98e0 f644feb0 c1365173 00000282 f5ff9460 f5ff96e0 f5ff96e0 f644feec
[ 4.186418] c1355bd8 f644c0e0 c1499c3d f5ff96e0 f644fed4 00000006 f5ff96e0 00000286
[ 4.186579] f644fedc c107922b f644feec 00000286 f5ff9460 f5ff9700 f644ff10 c135839e
[ 4.186739] Call Trace:
[ 4.186802] [<c1365173>] sdhci_set_ios+0x1c3/0x340
[ 4.186883] [<c1355bd8>] mmc_gate_clock+0x68/0x120
[ 4.186963] [<c1499c3d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
[ 4.187052] [<c107922b>] ? trace_hardirqs_on+0xb/0x10
[ 4.187134] [<c135839e>] mmc_host_clk_gate_delayed+0xbe/0x130
[ 4.187219] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187300] [<c135841d>] mmc_host_clk_gate_work+0xd/0x10
[ 4.187379] [<c105ec82>] process_one_work+0x172/0x5b0
[ 4.187457] [<c105ec09>] ? process_one_work+0xf9/0x5b0
[ 4.187538] [<c1358410>] ? mmc_host_clk_gate_delayed+0x130/0x130
[ 4.187625] [<c105f3c8>] worker_thread+0x118/0x330
[ 4.187700] [<c1496cee>] ? preempt_schedule+0x2e/0x50
[ 4.187779] [<c105f2b0>] ? rescuer_thread+0x1f0/0x1f0
[ 4.187857] [<c1062cf4>] kthread+0x74/0x80
[ 4.187931] [<c1062c80>] ? __init_kthread_worker+0x60/0x60
[ 4.188015] [<c149acfa>] kernel_thread_helper+0x6/0xd
[ 4.188079] Code: 81 fa 00 00 04 00 0f 84 a7 00 00 00 7f 21 81 fa 80 00 00 00 0f 84 92 00 00 00 81 fa 00 00 0
[ 4.188780] EIP: [<c136364e>] sdhci_set_power+0x3e/0xd0 SS:ESP 0068:f644fe94
[ 4.188898] ---[ end trace a7b23eecc71777e4 ]---
This BUG() comes from the fact that ios.power_mode was still in previous
value (MMC_POWER_ON) and ios.vdd was set to zero.
We prevent these by inhibiting the clock gating while we update the ios
structure.
Both problems can be reproduced by simply running the device in a reboot
loop.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per suggestion by Linus Walleij:
> If you think the names of the functions are confusing then
> you may rename them, say like this:
>
> mmc_host_clk_ungate() -> mmc_host_clk_hold()
> mmc_host_clk_gate() -> mmc_host_clk_release()
>
> Which would make the usecases more clear
(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.
drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix below compile warning:
CC drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts. This makes SDIO work.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung SoCs need to set BROKEN_ADMA_ZEROLEN_DESC.
(If ADMA operation is more than 65535, maybe set by zero.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable the quirk.
(Best used in conjunction with patch downgrading ADMA to SDMA when
transfer is not aligned.)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.
Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The patch adds device tree probe support for sdhci-esdhc-imx driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
Neither platform based nor dt based device needs to pass the parent
to sdhci_alloc_host. There is no difference between platform and dt
on this point.
The patch makes the change to pass device itself than its parent to
sdhci_alloc_host for dt case too. Otherwise the probe function of
sdhci based drivers which is shared between platform and dt will
fail on dt case.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch removes all the uses of cpu_is_mx(). Instead, it utilizes
platform_device_id to distinguish the esdhc differences among SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch copies platform data into pltfm_imx_data and reference
the data there than platform data after probe.
This work is inspired by Grant Likely and Troy Kisky.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Chris Ball <cjb@laptop.org>
The patch extends card_detect and write_protect support to get mx5
family and more scenarios supported. The changes include:
* Turn platform_data from optional to mandatory
* Add cd_types and wp_types into platform_data to cover more use
cases
* Remove the use of flag ESDHC_FLAG_GPIO_FOR_CD
* Adjust some machine codes to adopt the platform_data changes
* Work around the issue that software reset will get card detection
circuit stop working
With this patch, card_detect and write_protect gets supported on
mx5 based platforms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Chris Ball <cjb@laptop.org>
Fix build issue caused by undefined struct scatterlist in
drivers/mmc/host/tmio_mmc.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
It is not necessary to share the same notifier.h.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1287 commits)
icmp: Fix regression in nexthop resolution during replies.
net: Fix ppc64 BPF JIT dependencies.
acenic: include NET_SKB_PAD headroom to incoming skbs
ixgbe: convert to ndo_fix_features
ixgbe: only enable WoL for magic packet by default
ixgbe: remove ifdef check for non-existent define
ixgbe: Pass staterr instead of re-reading status and error bits from descriptor
ixgbe: Move interrupt related values out of ring and into q_vector
ixgbe: add structure for containing RX/TX rings to q_vector
ixgbe: inline the ixgbe_maybe_stop_tx function
ixgbe: Update ATR to use recorded TX queues instead of CPU for routing
igb: Fix for DH89xxCC near end loopback test
e1000: always call e1000_check_for_link() on e1000_ce4100 MACs.
netxen: add fw version compatibility check
be2net: request native mode each time the card is reset
ipv4: Constrain UFO fragment sizes to multiples of 8 bytes
virtio_net: Fix panic in virtnet_remove
ipv6: make fragment identifications less predictable
ipv6: unshare inetpeers
can: make function can_get_bittiming static
...
At http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg08371.html
(thread: "mmc: sdio: reset card during power_restore") we found and
fixed a bug where mmc's runtime power management functions were not being
called. We have now also made improvements to the SDIO powerup routine
which could possibly mask this kind of issue in future.
Add debug messages to the runtime PM hooks so that it is easy to verify
if and when runtime PM is happening.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case where a driver returns -ENOSYS from its suspend handler
to indicate that the device should be powered down over suspend, the
remove routine of the driver was not being called, leading to lots of
confusion during resume.
The problem is that runtime PM is disabled during this process,
and when we reach mmc_sdio_remove, calling the runtime PM functions here
(validly) return errors, and this was causing us to skip the remove
function.
Fix this by ignoring the error value of pm_runtime_get_sync(), which
can return valid errors. This also matches the behaviour of
pci_device_remove().
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix clock rate setting in the mxs-mmc driver. Previously, if div2 was 0
then the value for TIMING_CLOCK_RATE would have been 255 instead of 0.
The limits for div1 (TIMING_CLOCK_DIVIDE) and div2 (TIMING_CLOCK_RATE+1)
were also not correctly defined.
Can easily be reproduced on mx23evk: default clock for high speed sdio
cards is 50 MHz. With a SSP_CLK of 28.8 MHz default), this resulted in
an actual clock rate of about 56 kHz. Tested on mx23evk.
Signed-off-by: Koen Beel <koen.beel@barco.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the tmio-mmc driver contains a recursive runtime PM method
invocation, which leads to a deadlock on a mutex. Avoid it by taking
care not to request DMA too early.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A recent commit "mmc: tmio: Share register access functions" has swapped
arguments of a macro and broken DMA with TMIO MMC. This patch fixes the
arguments back.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses runtime PM to allow the system to power down the MMC
controller, when the MMC closk is switched off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Calling mmc_request_done() under a spinlock with interrupts disabled
leads to a recursive spin-lock on request retry path and to
scheduling in atomic context. This patch fixes both these problems
by moving mmc_request_done() to the scheduler workqueue.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case of an I/O error, the DMA will have been cleaned up in
the MMC interrupt and the request structure pointer will be null.
In that case, it is essential to check if the DMA is over before
dereferencing host->mrq->data.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are a few places with the same functionality. This patch creates
two functions omap_hsmmc_set_bus_width() and omap_hsmmc_set_bus_mode()
to do the job.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are two pieces of code which are similar, but not the same.
Each of them contains a bug.
The SYSCTL register should be read before writing to it in
omap_hsmmc_context_restore() to retain the state of the reserved bits.
Before setting the clock divisor and DTO bits the value from the SYSCTL
register should be masked properly. We were lucky to have no problems
with DTO bits. So, make sure we have clear DTO bits properly in
omap_hsmmc_set_ios().
Additionally get rid of msleep(1). The actual time is rarely higher
than 30us on OMAP 3630.
The resulting pieces of code are refactored into the
omap_hsmmc_set_clock() function.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is similar code in two functions which enable the clock. Refactor
this code to omap_hsmmc_start_clock(). Re-use omap_hsmmc_stop_clock() in
omap_hsmmc_context_restore() as well.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are two places where the same calculations are done.
Let's split them into a separate function.
In addition, simplify by using the DIV_ROUND_UP kernel macro.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move the min and max frequency constants to the definition block in
the source file.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
