Commit Graph

14 Commits

Author SHA1 Message Date
Maxime Ripard
1eb3927c20
ARM: dts: sun5i: Provide default muxing for relevant controllers
The I2C's, MMC0 and MMC1 controllers have only one muxing option in the
SoC. In such a case, we can just move the muxing into the DTSI, and remove
it from the DTS.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 15:14:06 +01:00
Maxime Ripard
6a9951a18b ARM: dts: sun5i: Change pinctrl nodes to avoid warning
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.

In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 11:37:08 +01:00
Maxime Ripard
79badc748b ARM: dts: sun5i: Remove card detect pull-up
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.

This also removes a DTC warning.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 11:36:57 +01:00
Maxime Ripard
f606c4b3b7 ARM: dts: sun5i: Remove all useless pinctrl nodes
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
2018-11-28 11:36:43 +01:00
Tuomas Tynkkynen
45e01f401a
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-02-13 09:37:22 +01:00
Maxime Ripard
1edcd36fcb ARM: sunxi: Convert pinctrl nodes to generic bindings
Now that we can handle the generic pinctrl bindings, convert our DT to it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:27:11 +01:00
Maxime Ripard
119c366aea ARM: sunxi: Remove useless allwinner,pull property
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).

Remove these properties to make it obvious that we do not set anything in
such a case.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:24:50 +01:00
Maxime Ripard
d312f6fb80 ARM: sunxi: Remove useless allwinner,drive property
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:24:50 +01:00
Hans de Goede
e6495c86a3 ARM: dts: sun5i: Add mmc1 / sdio-wifi node to mk802
The a10s mk802 uses a rtl8189es sdio wifi chip, add a node enabling
the mmc1 controller, this enables using the wifi chip (together with
an out of tree sdio driver for it).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-04 21:18:10 +02:00
Hans de Goede
afdfcf7c81 ARM: dts: sun5i: Add axp152 pmic node to mk802
Add a node describing the axp152 pmic to the mk802 dts, note there are
no regulator nodes as we do not yet support the regulators on the
axp152.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-04 21:18:09 +02:00
Hans de Goede
ba40e221de ARM: dts: sun5i: Enable otg on the mk802
Enable the otg controller, the id pin is not connected so enable
it in peripheral only mode.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-04 21:18:09 +02:00
Maxime Ripard
c0c2eb2476 ARM: sunxi: dt: Remove the FSF address
The FSF address triggers a warning on checkpatch, saying that the FSF
license is already present in the Linux source code, and that it has
already changed in the past.

Remove it from our DT, as suggested.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-05-10 10:22:23 +02:00
Maxime Ripard
59ebbe88a6 ARM: sunxi: DT: Add stdout-path property
Add UART aliases and stdout-path property for all the Allwinner boards so that
we won't have to rely on the bootargs' console= value, while working with
legacy bootloaders.

While we're at it, also remove the mentions of earlyprintk in the bootargs,
that will remove our default bootargs entirely, and allow the kernel to boot on
a system even if DEBUG_LL is configured for another system.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-04-27 08:20:30 +02:00
Hans de Goede
a084a779d6 ARM: dts: sun5i: Add mk802_a10s board
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.

For more details see: http://linux-sunxi.org/Semitime_g2

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Changed the compatible and node names labels]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2015-01-21 09:59:19 +01:00