Remove cite "Not sure what this does, but it is absolutely essential".
Extract initialization of trackstick part when touchpad is in passthrough
mode for v3 and v6 protocols into own function. Initialization for v3 is:
setscale11, setscale11, setscale11, nibble 0x9, nibble 0x4. Initialization
for v6 is: setscale11, setscale11, setscale11, setrate 0xC8, setrate 0x14.
Nibbles 0x9 and 0x4 for v3 protocol correspond to setrate 0xC8 and 0x14,
therefore these sequences are same.
When touchpad is in passthrough mode, then OS communicates with trackstick
and this sequence is some magic vendor PS/2 command to put trackstick into
"extended" mode. After that sequence trackstick starts reporting packets in
some vendor 4 bytes format (first byte is always 0xE8).
Next step after configuring trackstick to be in "extended" mode, is to
configure touchpad for v3 protocol to expect that trackstick reports data
in "extended" mode. For v3 protocol this is done by setting bit 1 in
register 0xC2C8 (offset 0x08 from base address 0xC2C0).
When both touchpad and trackstick are not configured for "extended" mode
then touchpad reports trackstick packets in different format, which is not
supported by psmouse/alps driver (yet).
In Cirque documentation GP-AN- 130823 INTERFACING TO GEN4 OVER I2C (PDF)
available at http://www.cirque.com/gen4-dev-resources is Logical Address
0xC2C8 named as PS2AuxControl and Bit Number 1 as ProcessAuxExtendedData
with description: Auxiliary device data is assumed to be extended data when
set.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch add support to handle MediaTek PMIC MT6397/MT6323 key
interrupts including pwrkey and homekey, also add setting for
long press key shutdown behavior.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Incorporates a series from Dmitry to remove platform data from
chromeos_laptop.c, which was the only user of platform data
for the atmel_mxt_ts driver.
Includes a series to clean up sysfs and debugfs for cros_ec.
Other misc. cleanups.
Thanks,
Benson
-----BEGIN PGP SIGNATURE-----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=mDkk
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- a series from Dmitry to remove platform data from chromeos_laptop.c,
which was the only user of platform data for the atmel_mxt_ts driver.
- a series to clean up sysfs and debugfs for cros_ec
- other misc cleanups
* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
platform/chrome: cros_ec_sysfs: Modify error handling
platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
Input: atmel_mxt_ts - remove platform data support
platform/chrome: chromeos_laptop - discard data for unneeded boards
platform/chrome: chromeos_laptop - use device properties for Pixel
platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
platform/chrome: chromeos_laptop - use I2C notifier to create devices
platform/chrome: chromeos_laptop - parse DMI IRQ data once
platform/chrome: chromeos_laptop - rework i2c peripherals initialization
platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
platform/chrome: chromeos_laptop - introduce pr_fmt()
platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
platform/chrome: chromeos_laptop - add SPDX identifier
Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
...
UI_SET_LEDBIT ioctl() causes the following KASAN splat when used with
led > LED_CHARGING:
[ 1274.663418] BUG: KASAN: slab-out-of-bounds in input_leds_connect+0x611/0x730 [input_leds]
[ 1274.663426] Write of size 8 at addr ffff88003377b2c0 by task ckb-next-daemon/5128
This happens because we were writing to the led structure before making
sure that it exists.
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Tested-by: Tasos Sahanidis <tasos@tasossah.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that there are no users of custom Atmel platform data, and everyone
has switched to the generic device properties, we can remove support for
the platform data.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Move older ChromeOS devices describing Atmel controllers in ACPI, but not
providing enough details to configure the controllers properly, from
platform data over to generic device properties. This will allow us
remove support for platform data later on, leaving only generic device
properties in place.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of using OF-specific APIs to fecth device properties, let's switch
to generic device properties API. This will allow us to use device
properties on legacy ChromeOS devices and get rid of platform data down
the road.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
The way we are supposed to put controller to sleep and wake it up does not
depend on the platform, but rather on controller itself, so we want to get
rid of suspend mode in platform data (and eventually get rid of platform
data completely). Unfortunately some early chromebooks (the original Pixel,
Acer C720) were shipped with config that requires manually re-enabling
touch reporting in T9. We will sort it out, but in the meantime let's
switch to a simple DMI quirk.
We'll keep pdata->suspend_mode for now and remove it when we rework
chromeos-laptop driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
When extending the rmi_spi buffers, we must check that no out of memory
error occurs, otherwise we may access data above the currently allocated
memory.
Propagate the error code returned by 'rmi_spi_manage_pools()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- new driver for PhoenixRC Flight Controller Adapter
- new driver for RAVE SP Power button
- fixes for autosuspend-related deadlocks in a few unput USB dirvers
- support for 2nd wheel in ATech PS/2 mouse
- fix for ALPS trackpoint detection on Thinkpad L570 and Latitude 7370
- bunch of cleanups in various in PS/2 protocols
- other assorted changes and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: i8042 - enable MUX on Sony VAIO VGN-CS series to fix touchpad
Input: stmfts, s6sy761 - update my e-mail
Input: stmfts - use async probe & suspend/resume to avoid 2s delay
Input: ALPS - fix TrackStick detection on Thinkpad L570 and Latitude 7370
Input: xpad - add PDP device id 0x02a4
Input: alps - report pressure of v3 and v7 trackstick
Input: pxrc - new driver for PhoenixRC Flight Controller Adapter
Input: usbtouchscreen - do not rely on input_dev->users
Input: usbtouchscreen - fix deadlock in autosuspend
Input: pegasus_notetaker - do not rely on input_dev->users
Input: pagasus_notetaker - fix deadlock in autosuspend
Input: synaptics_usb - do not rely on input_dev->users
Input: synaptics_usb - fix deadlock in autosuspend
Input: gpio-keys - add support for wakeup event action
Input: appletouch - use true and false for boolean values
Input: silead - add Chuwi Hi8 support
Input: analog - use get_cycles() on PPC
Input: stmpe-keypad - remove VLA usage
Input: i8042 - add Lenovo ThinkPad L460 to i8042 reset list
Input: add RAVE SP Powerbutton driver
...
The touch sensor buttons on Sony VAIO VGN-CS series laptops (e.g.
VGN-CS31S) are a separate PS/2 device. As the MUX is disabled for all
VAIO machines by the nomux blacklist, the data from touch sensor
buttons and touchpad are combined. The protocol used by the buttons is
probably similar to the touchpad protocol (both are Synaptics) so both
devices get enabled. The controller combines the data, creating a mess
which results in random button clicks, touchpad stopping working and
lost sync error messages:
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 4
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse serio1: issuing reconnect request
Add a new i8042_dmi_forcemux_table whitelist with VGN-CS.
With MUX enabled, touch sensor buttons are detected as separate device
(and left disabled as there's currently no driver), fixing all touchpad
problems.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull time(r) updates from Thomas Gleixner:
"A small set of updates for timers and timekeeping:
- The most interesting change is the consolidation of clock MONOTONIC
and clock BOOTTIME.
Clock MONOTONIC behaves now exactly like clock BOOTTIME and does
not longer ignore the time spent in suspend. A new clock
MONOTONIC_ACTIVE is provived which behaves like clock MONOTONIC in
kernels before this change. This allows applications to
programmatically check for the clock MONOTONIC behaviour.
As discussed in the review thread, this has the potential of
breaking user space and we might have to revert this. Knock on wood
that we can avoid that exercise.
- Updates to the NTP mechanism to improve accuracy
- A new kernel internal data structure to aid the ongoing Y2038 work.
- Cleanups and simplifications of the clocksource code.
- Make the alarmtimer code play nicely with debugobjects"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
alarmtimer: Init nanosleep alarm timer on stack
y2038: Introduce struct __kernel_old_timeval
tracing: Unify the "boot" and "mono" tracing clocks
hrtimer: Unify MONOTONIC and BOOTTIME clock behavior
posix-timers: Unify MONOTONIC and BOOTTIME clock behavior
timekeeping: Remove boot time specific code
Input: Evdev - unify MONOTONIC and BOOTTIME clock behavior
timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock
timekeeping: Add the new CLOCK_MONOTONIC_ACTIVE clock
timekeeping/ntp: Determine the multiplier directly from NTP tick length
timekeeping/ntp: Don't align NTP frequency adjustments to ticks
clocksource: Use ATTRIBUTE_GROUPS
clocksource: Use DEVICE_ATTR_RW/RO/WO to define device attributes
clocksource: Don't walk the clocksource list for empty override
-----BEGIN PGP SIGNATURE-----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=bzhS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CEC pin injection code for testing purposes
- DVB frontend cxd2099 promoted from staging
- new platform driver for Sony cxd2880 DVB devices
- new sensor drivers: mt9t112, ov2685, ov5695, ov772x, tda1997x,
tw9910.c
- removal of unused cx18 and ivtv alsa mixers
- the reneseas-ceu driver doesn't depend on soc_camera anymore and
moved from staging
- removed the mantis_vp3028 driver, unused since 2009
- s5p-mfc: add support for version 10 of the MSP
- added a decoder for imon protocol
- atomisp: lots of cleanups
- imx074 and mt9t031: don't depend on soc_camera anymore, being
promoted from staging
- added helper functions to better support DVB I2C binding
- lots of driver improvements and cleanups
* tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (438 commits)
media: v4l2-ioctl: rename a temp var that stores _IOC_SIZE(cmd)
media: fimc-capture: get rid of two warnings
media: dvb-usb-v2: fix a missing dependency of I2C_MUX
media: uvc: to the right check at uvc_ioctl_enum_framesizes()
media: cec-core: fix a bug at cec_error_inj_write()
media: tda9840: cleanup a warning
media: tm6000: avoid casting just to print pointer address
media: em28xx-input: improve error handling code
media: zr364xx: avoid casting just to print pointer address
media: vivid-radio-rx: add a cast to avoid a warning
media: saa7134-alsa: don't use casts to print a buffer address
media: solo6x10: get rid of an address space warning
media: zoran: don't cast pointers to print them
media: ir-kbd-i2c: change the if logic to avoid a warning
media: ir-kbd-i2c: improve error handling code
media: saa7134-input: improve error handling
media: s2255drv: fix a casting warning
media: ivtvfb: Cleanup some warnings
media: videobuf-dma-sg: Fix a weird cast
soc_camera: fix a weird cast on printk
...
Pull parisc updates from Helge Deller:
"Lots of small enhancements and fixes in this patchset:
- improved the x86-64 compatibility for PCI cards by returning -1UL
for timed out MMIO transactions (instead of crashing)
- fixed HPMC handler for PAT machines: size needs to be multiple of 16
- prepare machine_power_off() to be able to turn rp3410 and c8000
machines off via IMPI
- added code to extract machine info for usage with qemu
- some init sections fixes
- lots of fixes for sparse-, ubsan- and uninitalized variables
warnings"
* 'parisc-4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix out of array access in match_pci_device()
parisc: Add code generator for Qemu/SeaBIOS machine info
parisc/pci: Switch LBA PCI bus from Hard Fail to Soft Fail mode
parisc: Fix HPMC handler by increasing size to multiple of 16 bytes
parisc: Directly call machine_power_off() in power button driver
parisc: machine_power_off() should call pm_power_off()
parisc/Kconfig: SMP kernels boot on all machines
parisc: Silence uninitialized variable warning in dbl_to_sgl_fcnvff()
parisc: Move various functions and strings to init section
parisc: Convert MAP_TYPE to cover 4 bits on parisc
parisc: Force to various endian types for sparse
parisc/gscps2: Fix sparse warnings
parisc/led: Fix sparse warnings
parisc/parport_gsc: Use NULL to avoid sparse warning
parisc/stifb: Use fb_memset() to avoid sparse warning
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
Because I will be leaving Samsung soon, for reachability update
my reference e-mail to etezian.org.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Executing stmfts_power_on() function lasts over 2 seconds, what
significantly slows down the boot and resume processes if driver is
compiled in. Avoid this delay by forcing this driver to be probed
and suspended/resumed asynchronously.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The primary interface for the touchpad device in Thinkpad L570 is SMBus,
so ALPS overlooked PS2 interface Firmware setting of TrackStick, and
shipped with TrackStick otp bit is disabled.
The address 0xD7 contains device number information, so we can identify
the device by checking this value, but to access it we need to enable
Command mode, and then re-enable the device. Devices shipped in Thinkpad
L570 report either 0x0C or 0x1D as device numbers, if we see them we assume
that the devices are DualPoints.
The same issue exists on Dell Latitude 7370.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196929
Fixes: 646580f793 ("Input: ALPS - fix multi-touch decoding on SS4 plus touchpads")
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Tested-by: Jaak Ristioja <jaak@ristioja.ee>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adds support for a PDP Xbox One controller with device ID
(0x06ef:0x02a4). The Product string for this device is "PDP Wired
Controller for Xbox One - Stealth Series | Phantom Black".
Signed-off-by: Francis Therien <frtherien@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ALPS v3 and v7 packet formats reports trackstick pressure. This information
is already parsed in unused "z" variable.
ALPS SS4 S2 devices already reports trackstick pressure as ABS_PRESSURE
attribute, therefore reports pressure in the same way also for v3 and v7.
This patch also updates parsing v3 pressure information, it is also stored
in 7 bits.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver let you plug in your RC controller to the adapter and
use it as input device in various RC simulators.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device is unused and suspended, a call to open will cause the
device to autoresume through the call to usb_autopm_get_interface().
input_dev->users is already incremented by the input subsystem,
therefore this expression will always be evaluated to true:
if (input->users || usbtouch->type->irq_always)
result = usb_submit_urb(usbtouch->irq, GFP_NOIO);
The same URB will then be fail when resubmitted in usbtouch_open().
Introduce usbtouch->is_open to keep track of the state instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_autopm_get_interface() that is called in usbtouch_open() does an
autoresume if the device is suspended.
input_dev->mutex used in usbtouch_resume() is in this case already
taken by the input subsystem and will cause a deadlock.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The blackfin architecture is getting removed, so this
one is obsolete as well.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The blackfin architecture is getting removed, so this
driver is now obsolete.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
If the device is unused and suspended, a call to open will cause the
device to autoresume through the call to usb_autopm_get_interface().
input_dev->users is already incremented by the input subsystem,
therefore this expression will always be evaluated to true:
if (pegasus->dev->users && usb_submit_urb(pegasus->irq, GFP_NOIO) < 0)
retval = -EIO;
The same URB will then be fail when resubmitted in pegasus_open().
Introduce pegasus->is_open to keep track of the state instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_autopm_get_interface() that is called in pegasus_open() does an
autoresume if the device is suspended.
input_dev->mutex used in pegasus_resume() is in this case already
taken by the input subsystem and will cause a deadlock.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device is unused and suspended, a call to open will cause the
device to autoresume through the call to usb_autopm_get_interface().
input_dev->users is already incremented by the input subsystem,
therefore this expression will always be evaluated to true:
if ((input_dev->users || (synusb->flags & SYNUSB_IO_ALWAYS)) &&
usb_submit_urb(synusb->urb, GFP_NOIO) < 0) {
retval = -EIO;
}
The same URB will then be fail when resubmitted in synusb_open().
Introduce synusb->is_open to keep track of the state instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_autopm_get_interface() that is called in synusb_open() does an
autoresume if the device is suspended.
input_dev->mutex used in synusb_resume() is in this case already
taken by the input subsystem and will cause a deadlock.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for specifying event actions to trigger wakeup when using
the gpio-keys input device as a wakeup source.
This would allow the device to configure when to wakeup the system. For
example a gpio-keys input device for pen insert, may only want to wakeup
the system when ejecting the pen.
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This commit add ACPI support for Chuwi Hi8 tablet. On the ACPI table of
the tablet, GSL1680 is registered as MSSL0001, so the driver does not
recognize the device. This commit resolve it.
Signed-off-by: Shohei Maruyama <cheat.sc.linux@outlook.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The analog joystick driver spits a warning at us:
drivers/input/joystick/analog.c:176:2: warning: #warning Precise timer
not defined for this architecture.
PPC has get_cycles() so use that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that the MONOTONIC and BOOTTIME clocks are indentical, remove all the
special casing.
The user space visible interfaces still support both clocks, but their behavior
is identical.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kevin Easton <kevin@guarana.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salyzyn <salyzyn@android.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/20180301165150.155899327@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation to enabling -Wvla, remove VLA and replace it with a
fixed-length array instead.
Fixed as part of the directive to remove all VLAs from the kernel:
https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reset i8042 before probing because of insufficient BIOS initialisation of
the i8042 serial controller. This makes Synaptics touchpad detection
possible. Without resetting the Synaptics touchpad is not detected because
there are always NACK messages from AUX port.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqceRweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG59gH/0CVX4x6EobO/PQu
CzLVtAoRGFuIghB6Gmbx3Q1Ck4sn4q2SqUKTtkf03yauRGvnJsEmd6wEZ8f2IOHy
f30nX9s+4irzpQUIum4rH9KP6SMVJfNXlSVSisnamA6MbhPre3/NRcAIBUxdE4cK
lP81TaT6Nvp5cOySlPjPdWSbN4B1froFQ6rZ/lvG406QzqCvKvlS39h6IYjOF7Ds
zB/h3RkyuK9YyxFUO338RTEQ583esc0jTiTN4Pzb6nH3x8aTawDqGrwI2B4mkTLw
vNSPPE2VW9to0cZX+J7TH+uusPNXIlHZCD9tXwqWe5M+sCrE2FuydnmpZIf1A2LY
aWs0KQs=
=4nyn
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc4' into next
Sync up with mainline to bring in RAVE MFD device core.
Pull input fixes from Dmitry Torokhov:
- we are reverting patch that was switched touchpad on Lenovo T460P
over to native RMI because on these boxes BIOS messes up with SMBus
controller state. We might re-enable it later once SMBus issue is
resolved
- disabling interrupts in matrix_keypad driver was racy
- mms114 now has SPDX header and matching MODULE_LICENSE
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - Lenovo Thinkpad T460p devices should use RMI"
Input: matrix_keypad - fix race when disabling interrupts
Input: mms114 - add SPDX identifier
Input: mms114 - fix license module information
This reverts commit 4828296982 which
caused the following issues:
1. On T460p with BIOS version 2.22 touchpad and trackpoint stop working
after suspend-resume cycle. Due to strange state of the device another
suspend is impossible.
The following dmesg errors can be observed:
thinkpad_acpi: EC reports that Thermal Table has changed
rmi4_smbus 7-002c: failed to get SMBus version number!
rmi4_physical rmi4-00: rmi_driver_reset_handler: Failed to read current IRQ mask.
rmi4_f01 rmi4-00.fn01: Failed to restore normal operation: -16.
rmi4_f01 rmi4-00.fn01: Resume failed with code -16.
rmi4_physical rmi4-00: Failed to suspend functions: -16
rmi4_smbus 7-002c: Failed to resume device: -16
PM: resume devices took 0.640 seconds
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-16).
rmi4_physical rmi4-00: rmi_driver_clear_irq_bits: Failed to change enabled interrupts!
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
psmouse: probe of serio3 failed with error -1
2. On another T460p with BIOS version 2.15 two finger scrolling gesture
on the touchpad stops working after suspend-resume cycle (about 75%
reproducibility, when it still works, the scrolling gesture becomes
laggy). Nothing suspicious appears in the dmesg.
Analysis form Richard Schütz:
"RMI is unreliable on the ThinkPad T460p because the device is affected
by the firmware behavior addressed in a7ae81952c ("i2c: i801: Allow
ACPI SystemIO OpRegion to conflict with PCI BAR")."
The affected devices often show:
i801_smbus 0000:00:1f.4: BIOS is accessing SMBus registers
i801_smbus 0000:00:1f.4: Driver SMBus register access inhibited
Reported-by: Richard Schütz <rschuetz@uni-koblenz.de>
Signed-off-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Tested-by: Martin Peres <martin.peres@linux.intel.com>
Tested-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch registers four standard control handlers using the corresponding
V4L2 framework.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
[hans.verkuil@cisco.com: lower-cased 0x0F and 0xF0]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These functions provide write access to the internal LCD panel registers
which also control the sensor. They can be used to disable the
preprocessor, set the illumination brightness, and adjust gain/contrast
(which are stored together in one register internally called "vsvideo").
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds parameter definitions and module parameters for the four
userspace controls that the SUR40 can currently provide.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The SUR40 can recognize specific printed patterns directly in hardware;
this information (i.e. the pattern id) is present but currently unused
in the blob structure.
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If matrix_keypad_stop() is executing and the keypad interrupt is triggered,
disable_row_irqs() may be called by both matrix_keypad_interrupt() and
matrix_keypad_stop() at the same time, causing interrupts to be disabled
twice and the keypad being "stuck" after resuming.
Take lock when setting keypad->stopped to ensure that ISR will not race
with matrix_keypad_stop() disabling interrupts.
Signed-off-by: Zhang Bo <zbsdta@126.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We do not need to call ps2_command() several times in a row, transmitting
every byte as it were a command byte, we can often pack it all in a single
command.
Also, now that ps2_command() handles retransmission, we do not need to do
it ourselves in trackpoint_power_on_reset().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When we probe PS/2 devices we first issue "Get ID" command and only if we
receive what we consider a valid keyboard or mouse ID we disable the device
and continue with protocol detection. That means that the device may be
transmitting motion or keystroke data, while we expect ACK response.
Instead of signaling failure if we see anything but ACK/NAK let's ignore
"garbage" response until we see ACK for the command byte (first byte). The
checks for subsequent ACKs of command parameters will continue be strict.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The devices are allowed to respond to either command byte or command
parameter with a NAK (0xfe), and the host is supposed to resend the
"correct" byte. The device then will either respond with ACK or ERR (0xfc).
Let's teach libps2 to handle the NAK responses properly, so that individual
drivers do not need to handle them.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Debugging via i8042.debug and analyzing raw PS/2 data stream may be
cumbersome as you need to locate the boundaries of commands, decipher the
sliced commands, etc, etc. Let's add a bit more high level debug statements
for ps2_sendbyte(), ps2_command(), and ps2_sliced_command().
We do not introduce a new module parameter, but rater rely on the kernel
having dynamic debug facility enabled (which most everyone has nowadays).
Enable with:
echo "file libps2.c +pf" > /sys/kernel/debug/dynamic_debug/control
or add "libps2.dyndbg=+pf" to the kernel command line.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to adding some debugging statements to PS/2 control
sequences let's move psmouse_sliced_command() into libps2 and rename it
to ps2_sliced_command().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using unsigned char for the byte data switch to using u8. Also
use unsigned int for the command codes and timeouts, and have
ps2_handle_ack() and ps2_handle_response() return bool instead of int, as
they do not return error codes but rather signal whether a byte was handled
or not handled. ps2_is_keyboard_id() now returns bool as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Individual labels of switch statements should have the same indentation
level as the switch statement itself.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This Far-Eastern company's PS/2 mice use a deviant format for the data
relating to movement of the scroll wheels for, at least, their dual wheel
mice, such as their "Optical GreatEye Wheelmouse" model "WOP-35". This
product has five "buttons" (one of which is the click action on the first
wheel) and TWO scroll wheels. However for a byte comprising d0-d7 instead
of setting one of d6-7 in the forth byte of the mouse data packet and a
twos complement number of scroll steps in the remaining d5-d0 (or d3-d0
should there be a fourth (BTN_SIDE - d4) or fifth (BTN_EXTRA - d5) button
to report; they only report a single +/- event for each wheel and use a bit
pattern that corresponds to +/-1 for the first wheel and +/- 2 for the
second in the lower nibble of the fourth byte.
The effect with existing code is that the second mouse wheel merely repeats
the effect of the first but providing two steps per click rather than the
one of the first wheel - so there is no HORIZONTAL scroll wheel movement
detected from the device as far as the rest of the kernel sees it.
This patch, if enabled by the "a4tech_workaround" module parameter modifies
the handling just for mice of type PSMOUSE_IMEX so that the second scroll
wheel movement gets correctly reported as REL_HWHEEL events. Should this
module parameter be activated for other mice of the same PSMOUSE_IMEX type
then it is possible that at the point where the mouse reports more than a
single movement step the user may start seeing horizontal rather than
vertical wheel events, but should the movement steps get to be more than
two at a time the hack will get immediately deactivated and the behaviour
will revert to the past code.
This was discussed around *fifteen* *years* *ago* on the LKML and the best
summary is in post https://lkml.org/lkml/2002/7/18/111 "Re: PS2 Input Core
Support" by Vojtech Pavlik. I was not able to locate any discussion later
than this on this topic.
Given that most users of the "psmouse" module will NOT want this additional
feature enabled I have taken the apparently erroneous step of defaulting
the module parameter that enables it to be "disabled" - this functionality
may interfere with the operation of "normal" mice of this type (until a
large enough scroll wheel movement is detected) so I cannot see how it
would want to be enabled for "normal" users - i.e. everyone without this
brand of mouse.
I am using this patch at the moment and I can confirm that it is working
for me as both a module and compiled into the kernel for my mouse that is
of the type (WOP-35) described - I note that it is still available from
certain on-line retailers and that the manufacturers site does not list
GNU/Linux as being supported on the product page - this patch however does
enable full use of this product:
http://www.a4tech.com/product.asp?cid=3D1&scid=3D8&id=3D22
Signed-off-by: Stephen Lyons <slysven@virginmedia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- use u8 instead of unsigned char for byte data
- use input_set_capability() instead of manipulating capabilities bits
directly
- do not abuse -1 as error code, propagate errors from various calls.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- switch to using BIT() macros
- use u8 instead of unsigned char for byte data
- use input_set_capability() instead of manipulating capabilities bits
directly
- use sign_extend32() when extracting wheel data.
- do not abuse -1 as error code, propagate errors from various calls.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- switch to using BIT() macros
- use u8 instead of unsigned char for byte data
- use input_set_capability() instead of manipulating capabilities bits
directly
- use sign_extend32() when extracting wheel data.
- do not abuse -1 as error code, propagate errors from various calls.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many protocol driver re-implement code to parse buttons or motion data from
the standard PS/2 protocol. Let's split the parsing into separate
functions and reuse them in protocol drivers.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace the original license statement with the SPDX identifier.
Add also one line of description as recommended by the COPYING
file.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver has been released with GNU Public License v2 as stated
in the header, but the module license information has been tagged
as "GPL" (GNU Public License v2 or later).
Fix the module license information so that it matches the one in
the header as "GPL v2".
Fixes: 07b8481d4a ("Input: add MELFAS mms114 touchscreen driver")
Reported-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer updates from Dmitry Torokhov:
- evdev interface has been adjusted to extend the life of timestamps on
32 bit systems to the year of 2108
- Synaptics RMI4 driver's PS/2 guest handling ha beed updated to
improve chances of detecting trackpoints on the pass-through port
- mms114 touchcsreen controller driver has been updated to support
generic device properties and work with mms152 cntrollers
- Goodix driver now supports generic touchscreen properties
- couple of drivers for AVR32 architecture are gone as the architecture
support has been removed from the kernel
- gpio-tilt driver has been removed as there are no mainline users and
the driver itself is using legacy APIs and relies on platform data
- MODULE_LINECSE/MODULE_VERSION cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: goodix - use generic touchscreen_properties
Input: mms114 - fix typo in definition
Input: mms114 - use BIT() macro instead of explicit shifting
Input: mms114 - replace mdelay with msleep
Input: mms114 - add support for mms152
Input: mms114 - drop platform data and use generic APIs
Input: mms114 - mark as direct input device
Input: mms114 - do not clobber interrupt trigger
Input: edt-ft5x06 - fix error handling for factory mode on non-M06
Input: stmfts - set IRQ_NOAUTOEN to the irq flag
Input: auo-pixcir-ts - delete an unnecessary return statement
Input: auo-pixcir-ts - remove custom log for a failed memory allocation
Input: da9052_tsi - remove unused mutex
Input: docs - use PROPERTY_ENTRY_U32() directly
Input: synaptics-rmi4 - log when we create a guest serio port
Input: synaptics-rmi4 - unmask F03 interrupts when port is opened
Input: synaptics-rmi4 - do not delete interrupt memory too early
Input: ad7877 - use managed resource allocations
Input: stmfts,s6sy671 - add SPDX identifier
Input: remove atmel-wm97xx touchscreen driver
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJabj6pAAoJEHm+PkMAQRiGs8cIAJQFkCWnbz86e3vG4DuWhyA8
CMGHCQdUOxxFGa/ixhIiuetbC0x+JVHAjV2FwVYbAQfaZB3pfw2iR1ncQxpAP1AI
oLU9vBEqTmwKMPc9CM5rRfnLFWpGcGwUNzgPdxD5yYqGDtcM8K840mF6NdkYe5AN
xU8rv1wlcFPF4A5pvHCH0pvVmK4VxlVFk/2H67TFdxBs4PyJOnSBnf+bcGWgsKO6
hC8XIVtcKCH2GfFxt5d0Vgc5QXJEpX1zn2mtCa1MwYRjN2plgYfD84ha0xE7J0B0
oqV/wnjKXDsmrgVpncr3txd4+zKJFNkdNRE4eLAIupHo2XHTG4HvDJ5dBY2NhGU=
=sOml
-----END PGP SIGNATURE-----
Merge tag 'v4.15' into next
Sync with mainline to get in trackpoint updates and other changes.
Use touchscreen_properties structure instead of implementing all
properties by our own. It allows us to reuse generic code for parsing
device-tree properties (which was implemented manually in the driver for
now). Additionally, it allows us to report events using generic
touchscreen_report_pos(), which automatically handles inverted and
swapped axes.
This fixes the issue with the custom code incorrectly handling case where
ts->inverted_x and ts->swapped_x_y were true, but ts->inverted_y was
false. Assuming we have 720x1280 touch panel, ts->abs_x_max == 1279 and
ts->abs_y_max == 719 (because we inverted that in goodix_read_config()).
Now let's assume that we received event from (0:0) position (in touch
panel original coordinates). In function goodix_ts_report_touch() we
calculate input_x as 1279, but after swapping input_y takes that value
(which is more that maximum 719 value reported during initialization).
Note that since touchscreen coordinates are 0-indexed, we now report
touchscreen range as (0:size-1).
Developed and tested on custom DT-based device with gt1151 touch
panel.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
[dtor: fix endianness annotation reported by sparse, handle errors when
initializing MT slots]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
200 milliseconds is a very long time to keep the CPU busy looping.
Use msleep instead.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS152 has no configuration registers, but the packet format used in
interrupts is identical to mms114.
Signed-off-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MMS114 platform data has no in-tree users, so drop it.
Switch to using the standard touchscreen properties via
touchscreen_parse_properties(), and move the old DT parsing code
to use device_property_*() APIs.
Finally, use touchscreen_report_pos to report x/y coordinates
and drop the custom x/y inversion code.
Signed-off-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
mms14 is a touchscreen and thus a direct input device; let's mark it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Also add error handling for input_mt_init_slots().
Reviewed-by: Simon Shields <simon@lineageos.org>
Tested-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"The main item is that we try to better handle the newer trackpoints on
Lenovo devices that are now being produced by Elan/ALPS/NXP and only
implement a small subset of the original IBM trackpoint controls"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics_rmi4 - use devm_device_add_group() for attributes in F01"
Input: trackpoint - only expose supported controls for Elan, ALPS and NXP
Input: trackpoint - force 3 buttons if 0 button is reported
Input: xpad - add support for PDP Xbox One controllers
Input: stmfts,s6sy671 - add SPDX identifier
Since the sysfs attribute hangs off the RMI bus, which doesn't go away during
firmware flash, it needs to be explicitly removed, otherwise we would try and
register the same attribute twice.
This reverts commit 36a44af5c1.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When attempting enter factory mode on firmware that does not support it,
we'd error out, but leave the device with interrupts disabled, and thus
touch not working. Fix it by moving the check before we disable
interrupts/allocate memory for debug buffers.
Fixes: fd335ab04b ("Input: edt-ft5x06 - add support for M09 firmware version")
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The interrupt is requested before the device is powered on and
it's value in some cases cannot be reliable. It happens on some
devices that an interrupt is generated as soon as requested
before having the chance to disable the irq.
Set the irq flag as IRQ_NOAUTOEN before requesting it.
This patch mutes the error:
stmfts 2-0049: failed to read events: -11
received sometimes during boot time.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The script "checkpatch.pl" pointed information out like the following:
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To ease analyzing boot behavior from logs, let's log when we are about to
register the pass-through serio port.
Also, let's drop "Synaptics" prefix from the port name, as RMI4 is good
enough indicator already, and having the prefix means that the name does
not fit into serio->name field. While at it move from hard-coded seio->phys
to one mentioning the sensor ID (such as "rmi4-00.fn03/serio0").
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently we register the pass-through serio port when we probe the F03 RMI
function, and then, in sensor configure phase, we unmask interrupts.
Unfortunately this is too late, as other drivers are free probe devices
attached to the serio port as soon as it is probed. Because interrupts are
masked, the IO times out, which may result in not being able to detect
trackpoints on the pass-through port.
To fix the issue we implement open() and close() methods for the
pass-through serio port and unmask interrupts from there. We also move
creation of the pass-through port form probe to configure stage, as RMI
driver does not enable transport interrupt until all functions are probed
(we should change this, but this is a separate topic).
We also try to clear the pending data before unmasking interrupts, because
some devices like to spam the system with multiple 0xaa 0x00 announcements,
which may interfere with us trying to query ID of the device.
Fixes: c5e8848fc9 ("Input: synaptics-rmi4 - add support for F03")
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We want to free memory reserved for interrupt mask handling only after we
free functions, as function drivers might want to mask interrupts. This is
needed for the followup patch to the F03 that would implement unmasking and
masking interrupts from the serio pass-through port open() and close()
methods.
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use managed resource allocations to simplify error handling during
probing failure and module exiting.
With this all the goto labels in the probe function together with
the cleanups in the remove function are unnecessary, therefore
removed.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace the original license statement with the SPDX identifier.
Update also the copyright owner adding myself as co-owner of the
copyright.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The newer trackpoints from ALPS, Elan and NXP implement a very limited
subset of extended commands and controls that the original trackpoints
implemented, so we should not be exposing not working controls in sysfs.
The newer trackpoints also do not implement "Power On Reset" or "Read
Extended Button Status", so we should not be using these commands during
initialization.
While we are at it, let's change "unsigned char" to u8 for byte data or
bool for booleans and use better suited error codes instead of -1.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo introduced trackpoint compatible sticks with minimum PS/2 commands.
They supposed to reply with 0x02, 0x03, or 0x04 in response to the
"Read Extended ID" command, so we would know not to try certain extended
commands. Unfortunately even some trackpoints reporting the original IBM
version (0x01 firmware 0x0e) now respond with incorrect data to the "Get
Extended Buttons" command:
thinkpad_acpi: ThinkPad BIOS R0DET87W (1.87 ), EC unknown
thinkpad_acpi: Lenovo ThinkPad E470, model 20H1004SGE
psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 0/0
Since there are no trackpoints without buttons, let's assume the trackpoint
has 3 buttons when we get 0 response to the extended buttons query.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196253
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adds support for the current lineup of Xbox One controllers from PDP
(Performance Designed Products). These controllers are very picky with
their initialization sequence and require an additional 2 packets before
they send any input reports.
Signed-off-by: Mark Furneaux <mark@furneaux.ca>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace the original license statement with the SPDX identifier.
Update also the copyright owner adding myself as co-owner of the
copyright.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a fix for use-after-free in Synaptics RMI4 driver
- correction to multitouch contact tracking on certain ALPS touchpads
(which got broken when we tried to fix the 2-finger scrolling)
- touchpad on Lenovo T640p is switched over to SMbus/RMI
- a few device node refcount fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - prevent UAF reported by KASAN
Input: ALPS - fix multi-touch decoding on SS4 plus touchpads
Input: synaptics - Lenovo Thinkpad T460p devices should use RMI
Input: of_touchscreen - add MODULE_LICENSE
Input: 88pm860x-ts - fix child-node lookup
Input: twl6040-vibra - fix child-node lookup
Input: twl4030-vibra - fix sibling-node lookup
Since AVR32 arch is gone, atmel-wm97xx driver is useless. In theory it
could have been rewritten to work with AT91 devices, but the driver is from
the platform data era, and a bit hard coded to work on AVR32 hardware
variant of the AC97C peripheral, so let's remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
