Add documentation for the tcp ULP tls interface.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 61b905da33 ("net: Rename skb->rxhash to skb->hash")
didn't update the documentation, fix this up.
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a control message that can be specified on the first sendmsg() of a
client call or the first sendmsg() of a service response to indicate the
total length of the data to be transmitted for that call.
Currently, because the length of the payload of an encrypted DATA packet is
encrypted in front of the data, the packet cannot be encrypted until we
know how much data it will hold.
By specifying the length at the beginning of the transmit phase, each DATA
packet length can be set before we start loading data from userspace (where
several sendmsg() calls may contribute to a particular packet).
An error will be returned if too little or too much data is presented in
the Tx phase.
Signed-off-by: David Howells <dhowells@redhat.com>
It's unused, so remove it.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update tcp.txt to fix mandatory congestion control ops and default
CCA selection. Also, fix comment in tcp.h for undo_cwnd.
Signed-off-by: Anmol Sarma <me@anmolsarma.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible for a client to use AuriStor's service upgrade facility.
The client does this by adding an RXRPC_UPGRADE_SERVICE control message to
the first sendmsg() of a call. This takes no parameters.
When recvmsg() starts returning data from the call, the service ID field in
the returned msg_name will reflect the result of the upgrade attempt. If
the upgrade was ignored, srx_service will match what was set in the
sendmsg(); if the upgrade happened the srx_service will be altered to
indicate the service the server upgraded to.
Note that:
(1) The choice of upgrade service is up to the server
(2) Further client calls to the same server that would share a connection
are blocked if an upgrade probe is in progress.
(3) This should only be used to probe the service. Clients should then
use the returned service ID in all subsequent communications with that
server (and not set the upgrade). Note that the kernel will not
retain this information should the connection expire from its cache.
(4) If a server that supports upgrading is replaced by one that doesn't,
whilst a connection is live, and if the replacement is running, say,
OpenAFS 1.6.4 or older or an older IBM AFS, then the replacement
server will not respond to packets sent to the upgraded connection.
At this point, calls will time out and the server must be reprobed.
Signed-off-by: David Howells <dhowells@redhat.com>
Implement AuriStor's service upgrade facility. There are three problems
that this is meant to deal with:
(1) Various of the standard AFS RPC calls have IPv4 addresses in their
requests and/or replies - but there's no room for including IPv6
addresses.
(2) Definition of IPv6-specific RPC operations in the standard operation
sets has not yet been achieved.
(3) One could envision the creation a new service on the same port that as
the original service. The new service could implement improved
operations - and the client could try this first, falling back to the
original service if it's not there.
Unfortunately, certain servers ignore packets addressed to a service
they don't implement and don't respond in any way - not even with an
ABORT. This means that the client must then wait for the call timeout
to occur.
What service upgrade does is to see if the connection is marked as being
'upgradeable' and if so, change the service ID in the server and thus the
request and reply formats. Note that the upgrade isn't mandatory - a
server that supports only the original call set will ignore the upgrade
request.
In the protocol, the procedure is then as follows:
(1) To request an upgrade, the first DATA packet in a new connection must
have the userStatus set to 1 (this is normally 0). The userStatus
value is normally ignored by the server.
(2) If the server doesn't support upgrading, the reply packets will
contain the same service ID as for the first request packet.
(3) If the server does support upgrading, all future reply packets on that
connection will contain the new service ID and the new service ID will
be applied to *all* further calls on that connection as well.
(4) The RPC op used to probe the upgrade must take the same request data
as the shadow call in the upgrade set (but may return a different
reply). GetCapability RPC ops were added to all standard sets for
just this purpose. Ops where the request formats differ cannot be
used for probing.
(5) The client must wait for completion of the probe before sending any
further RPC ops to the same destination. It should then use the
service ID that recvmsg() reported back in all future calls.
(6) The shadow service must have call definitions for all the operation
IDs defined by the original service.
To support service upgrading, a server should:
(1) Call bind() twice on its AF_RXRPC socket before calling listen().
Each bind() should supply a different service ID, but the transport
addresses must be the same. This allows the server to receive
requests with either service ID.
(2) Enable automatic upgrading by calling setsockopt(), specifying
RXRPC_UPGRADEABLE_SERVICE and passing in a two-member array of
unsigned shorts as the argument:
unsigned short optval[2];
This specifies a pair of service IDs. They must be different and must
match the service IDs bound to the socket. Member 0 is the service ID
to upgrade from and member 1 is the service ID to upgrade to.
Signed-off-by: David Howells <dhowells@redhat.com>
Permit bind() to be called on an AF_RXRPC socket more than once (currently
maximum twice) to bind multiple listening services to it. There are some
restrictions:
(1) All bind() calls involved must have a non-zero service ID.
(2) The service IDs must all be different.
(3) The rest of the address (notably the transport part) must be the same
in all (a single UDP socket is shared).
(4) This must be done before listen() or sendmsg() is called.
This allows someone to connect to the service socket with different service
IDs and lays the foundation for service upgrading.
The service ID used by an incoming call can be extracted from the msg_name
returned by recvmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
The addition of the AVF and virtchnl code to the i40evf driver
means we should update the i40evf.txt file with the most up to date
information.
It seems this file hasn't been updated in a while, so the
changes cover a little more than just AVF, but it's all only
in the i40evf.txt.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SOF_TIMESTAMPING_OPT_TX_SWHW option to allow an outgoing packet to
be looped to the socket's error queue with a software timestamp even
when a hardware transmit timestamp is expected to be provided by the
driver.
Applications using this option will receive two separate messages from
the error queue, one with a software timestamp and the other with a
hardware timestamp. As the hardware timestamp is saved to the shared skb
info, which may happen before the first message with software timestamp
is received by the application, the hardware timestamp is copied to the
SCM_TIMESTAMPING control message only when the skb has no software
timestamp or it is an incoming packet.
While changing sw_tx_timestamp(), inline it in skb_tx_timestamp() as
there are no other users.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scm_timestamping struct may return multiple non-zero fields, e.g.
when both software and hardware RX timestamping is enabled, or when the
SO_TIMESTAMP(NS) option is combined with SCM_TIMESTAMPING and a false
software timestamp is generated in the recvmsg() call in order to always
return a SCM_TIMESTAMP(NS) message.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SOF_TIMESTAMPING_OPT_PKTINFO option to request a new control message
for incoming packets with hardware timestamps. It contains the index of
the real interface which received the packet and the length of the
packet at layer 2.
The index is useful with bonding, bridges and other interfaces, where
IP_PKTINFO doesn't allow applications to determine which PHC made the
timestamp. With the L2 length (and link speed) it is possible to
transpose preamble timestamps to trailer timestamps, which are used in
the NTP protocol.
While this information could be provided by two new socket options
independently from timestamping, it doesn't look like they would be very
useful. With this option any performance impact is limited to hardware
timestamping.
Use dev_get_by_napi_id() to get the device and its index. On kernels
with disabled CONFIG_NET_RX_BUSY_POLL or drivers not using NAPI, a zero
index will be returned in the control message.
CC: Richard Cochran <richardcochran@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_csum_hwoffload_help() uses netdev features and skb->csum_not_inet to
determine if skb needs software computation of Internet Checksum or crc32c
(or nothing, if this computation can be done by the hardware). Use it in
place of skb_checksum_help() in validate_xmit_skb() to avoid corruption
of non-GSO SCTP packets having skb->ip_summed equal to CHECKSUM_PARTIAL.
While at it, remove references to skb_csum_off_chk* functions, since they
are not present anymore in Linux _ see commit cf53b1da73 ("Revert
"net: Add driver helper functions to determine checksum offloadability"").
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
guide for user-space API documents, rather sparsely populated at the
moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of Documentation/
to fix comments elsewhere in the tree; I have acks for those where I could
get them.
-----BEGIN PGP SIGNATURE-----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=41m+
-----END PGP SIGNATURE-----
Merge tag 'docs-4.12' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"A reasonably busy cycle for documentation this time around. There is a
new guide for user-space API documents, rather sparsely populated at
the moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of
Documentation/ to fix comments elsewhere in the tree; I have acks for
those where I could get them"
* tag 'docs-4.12' of git://git.lwn.net/linux: (74 commits)
docs: Fix a couple typos
docs: Fix a spelling error in vfio-mediated-device.txt
docs: Fix a spelling error in ioctl-number.txt
MAINTAINERS: update file entry for HSI subsystem
Documentation: allow installing man pages to a user defined directory
Doc/PM: Sync with intel_powerclamp code behavior
zr364xx.rst: usb/devices is now at /sys/kernel/debug/
usb.rst: move documentation from proc_usb_info.txt to USB ReST book
convert philips.txt to ReST and add to media docs
docs-rst: usb: update old usbfs-related documentation
arm: Documentation: update a path name
docs: process/4.Coding.rst: Fix a couple of document refs
docs-rst: fix usb cross-references
usb: gadget.h: be consistent at kernel doc macros
usb: composite.h: fix two warnings when building docs
usb: get rid of some ReST doc build errors
usb.rst: get rid of some Sphinx errors
usb/URB.txt: convert to ReST and update it
usb/persist.txt: convert to ReST and add to driver-api book
usb/hotplug.txt: convert to ReST and add to driver-api book
...
Figure 1 is full of whitespaces; fix it
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Middlebox firewall issues can potentially cause server's data being
blackholed after a successful 3WHS using TFO. Following are the related
reports from Apple:
https://www.nanog.org/sites/default/files/Paasch_Network_Support.pdf
Slide 31 identifies an issue where the client ACK to the server's data
sent during a TFO'd handshake is dropped.
C ---> syn-data ---> S
C <--- syn/ack ----- S
C (accept & write)
C <---- data ------- S
C ----- ACK -> X S
[retry and timeout]
https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf
Slide 5 shows a similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C? X <- data ------ S
[retry and timeout]
This is the worst failure b/c the client can not detect such behavior to
mitigate the situation (such as disabling TFO). Failing to proceed, the
application (e.g., SSL library) may simply timeout and retry with TFO
again, and the process repeats indefinitely.
The proposed solution is to disable active TFO globally under the
following circumstances:
1. client side TFO socket detects out of order FIN
2. client side TFO socket receives out of order RST
We disable active side TFO globally for 1hr at first. Then if it
happens again, we disable it for 2h, then 4h, 8h, ...
And we reset the timeout to 1hr if a client side TFO sockets not opened
on loopback has successfully received data segs from server.
And we examine this condition during close().
The rational behind it is that when such firewall issue happens,
application running on the client should eventually close the socket as
it is not able to get the data it is expecting. Or application running
on the server should close the socket as it is not able to receive any
response from client.
In both cases, out of order FIN or RST will get received on the client
given that the firewall will not block them as no data are in those
frames.
And we want to disable active TFO globally as it helps if the middle box
is very close to the client and most of the connections are likely to
fail.
Also, add a debug sysctl:
tcp_fastopen_blackhole_detect_timeout_sec:
the initial timeout to use when firewall blackhole issue happens.
This can be set and read.
When setting it to 0, it means to disable the active disable logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
update the list and remove 'in the future' statement,
since all still alive 64-bit architectures now do eBPF JIT.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no usbfs anymore. The old features are now either
exported to /dev/bus/usb or via debugfs.
Update documentation accordingly, pointing to the new
places where the character devices and usb/devices are
now placed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
As ftp.kernel.org is closed [0], this commit fixes dead URLs in
documents to use www.kernel.org instead.
[0] https://www.kernel.org/shutting-down-ftp-services.html
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-23
This series contains updates to i40e and i40e.txt documentation.
Jake provides all the changes in the series which are centered around
ntuple filter fixes and additional support. Fixed the current
implementation of .set_rxnfc, where we were not reading the mask field
for filter entries which was resulting in filters not behaving as
expected and not working correctly. When cleaning up after disabling
flow director support, ensure that the default input set is correctly
reprogrammed. Since the hardware only supports a single input set for
all flows of that type, the driver shall only allow the input set to
change if there are no other configured filters for that flow type, so
add support to detect when we can update the input set for each flow
type. Align the driver to other drivers to partition the ring_cookie
value into 8bits of VF index, along with 32bits of queue number instead
of using the user-def field. Added support to parse the user-def field
into a data structure format to allow future extensions of the user-def
filed by keeping all the code that read/writes the field into a single
location. Added support for flexible payloads passed via ethtool
user-def field. We support a single flexible word (2byte) value per
protocol type, and we handle the FLX_PIT register using a list of
flexible entries so that each flow type may be configured separately.
Enabled flow director filters for SCTPv4 packets using the ethtool
ntuple interface to enable filters. Updated the documentation on the
i40e driver to include the newly added support to ntuple filters.
Reduced complexity of a if-continue-else-break section of code by
taking advantage of using hlist_for_each_entry_continue() instead.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain system process significant unconnected UDP workload.
It would be preferrable to disable UDP early demux for those systems
and enable it for TCP only.
By disabling UDP demux, we see these slight gains on an ARM64 system-
782 -> 788Mbps unconnected single stream UDPv4
633 -> 654Mbps unconnected UDPv4 different sources
The performance impact can change based on CPU architecure and cache
sizes. There will not much difference seen if entire UDP hash table
is in cache.
Both sysctls are enabled by default to preserve existing behavior.
v1->v2: Change function pointer instead of adding conditional as
suggested by Stephen.
v2->v3: Read once in callers to avoid issues due to compiler
optimizations. Also update commit message with the tests.
v3->v4: Store and use read once result instead of querying pointer
again incorrectly.
v4->v5: Refactor to avoid errors due to compilation with IPV6={m,n}
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Suggested-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Tom Herbert <tom@herbertland.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation describing the drivers use of ethtool ntuple filters,
including the limitations that it has due to hardware, as well as how it
reads and parses the user-def data block.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds a new sysctl accept_ra_rt_info_min_plen that
defines the minimum acceptable prefix length of Route Information
Options. The new sysctl is intended to be used together with
accept_ra_rt_info_max_plen to configure a range of acceptable
prefix lengths. It is useful to prevent misconfigurations from
unintentionally blackholing too much of the IPv6 address space
(e.g., home routers announcing RIOs for fc00::/7, which is
incorrect).
Signed-off-by: Joel Scherpelz <jscherpelz@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ECMP hash policy choice via a new sysctl
called fib_multipath_hash_policy and also adds support for L4 hashes.
The current values for fib_multipath_hash_policy are:
0 - layer 3 (default)
1 - layer 4
If there's an skb hash already set and it matches the chosen policy then it
will be used instead of being calculated (currently only for L4).
In L3 mode we always calculate the hash due to the ICMP error special
case, the flow dissector's field consistentification should handle the
address order thus we can remove the address reversals.
If the skb is provided we always use it for the hash calculation,
otherwise we fallback to fl4, that is if skb is NULL fl4 has to be set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your
net-next tree. A couple of new features for nf_tables, and unsorted
cleanups and incremental updates for the Netfilter tree. More
specifically, they are:
1) Allow to check for TCP option presence via nft_exthdr, patch
from Phil Sutter.
2) Add symmetric hash support to nft_hash, from Laura Garcia Liebana.
3) Use pr_cont() in ebt_log, from Joe Perches.
4) Remove some dead code in arp_tables reported via static analysis
tool, from Colin Ian King.
5) Consolidate nf_tables expression validation, from Liping Zhang.
6) Consolidate set lookup via nft_set_lookup().
7) Remove unnecessary rcu read lock side in bridge netfilter, from
Florian Westphal.
8) Remove unused variable in nf_reject_ipv4, from Tahee Yoo.
9) Pass nft_ctx struct to object initialization indirections, from
Florian Westphal.
10) Add code to integrate conntrack helper into nf_tables, also from
Florian.
11) Allow to check if interface index or name exists via
NFTA_FIB_F_PRESENT, from Phil Sutter.
12) Simplify resolve_normal_ct(), from Florian.
13) Use per-limit spinlock in nft_limit and xt_limit, from Liping Zhang.
14) Use rwlock in nft_set_rbtree set, also from Liping Zhang.
15) One patch to remove a useless printk at netns init path in ipvs,
and several patches to document IPVS knobs.
16) Use refcount_t for reference counter in the Netfilter/IPVS code,
from Elena Reshetova.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The tcp_tw_recycle was already broken for connections
behind NAT, since the per-destination timestamp is not
monotonically increasing for multiple machines behind
a single destination address.
After the randomization of TCP timestamp offsets
in commit 8a5bd45f6616 (tcp: randomize tcp timestamp offsets
for each connection), the tcp_tw_recycle is broken for all
types of connections for the same reason: the timestamps
received from a single machine is not monotonically increasing,
anymore.
Remove tcp_tw_recycle, since it is not functional. Also, remove
the PAWSPassive SNMP counter since it is only used for
tcp_tw_recycle, and simplify tcp_v4_route_req and tcp_v6_route_req
since the strict argument is only set when tcp_tw_recycle is
enabled.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Lutz Vieweg <lvml@5t9.de>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document sysctl pmtu_disc based on commit 3654e61137 ("ipvs: add
pmtu_disc option to disable IP DF for TUN packets").
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Document sysctl sync_ports based on commit f73181c828 ("ipvs: add support
for sync threads").
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Document sysctl sync_qlen_max and sync_sock_size based on
commit 1c003b1580 ("ipvs: wakeup master thread").
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Fix sync_threshold description which should have two values. Also add
sync_refresh_period and sync_retries based on commit 749c42b620
("ipvs: reduce sync rate with time thresholds").
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow TTL propagation from IP packets to MPLS packets to be
configured. Add a new optional LWT attribute, MPLS_IPTUNNEL_TTL, which
allows the TTL to be set in the resulting MPLS packet, with the value
of 0 having the semantics of enabling propagation of the TTL from the
IP header (i.e. non-zero values disable propagation).
Also allow the configuration to be overridden globally by reusing the
same sysctl to control whether the TTL is propagated from IP packets
into the MPLS header. If the per-LWT attribute is set then it
overrides the global configuration. If the TTL isn't propagated then a
default TTL value is used which can be configured via a new sysctl,
"net.mpls.default_ttl". This is kept separate from the configuration
of whether IP TTL propagation is enabled as it can be used in the
future when non-IP payloads are supported (i.e. where there is no
payload TTL that can be propagated).
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide the ability to control on a per-route basis whether the TTL
value from an MPLS packet is propagated to an IPv4/IPv6 packet when
the last label is popped as per the theoretical model in RFC 3443
through a new route attribute, RTA_TTL_PROPAGATE which can be 0 to
mean disable propagation and 1 to mean enable propagation.
In order to provide the ability to change the behaviour for packets
arriving with IPv4/IPv6 Explicit Null labels and to provide an easy
way for a user to change the behaviour for all existing routes without
having to reprogram them, a global knob is provided. This is done
through the addition of a new per-namespace sysctl,
"net.mpls.ip_ttl_propagate", which defaults to enabled. If the
per-route attribute is set (either enabled or disabled) then it
overrides the global configuration.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It wasn't clear if the 'forwarding' setting needs to be enabled on the
interface that packets are received from, or on the interface that
packets are forwarded to, or both.
In fact (according to my code reading) the setting is relevant on the
interface that packets are received from, so this change updates the doc
to say that.
Signed-off-by: Neil Jerram <neil@tigera.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typos and add the following to the scripts/spelling.txt:
an user||a user
an userspace||a userspace
I also added "userspace" to the list since it is a common word in Linux.
I found some instances for "an userfaultfd", but I did not add it to the
list. I felt it is endless to find words that start with "user" such as
"userland" etc., so must draw a line somewhere.
Link: http://lkml.kernel.org/r/1481573103-11329-4-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Three more DocBook template files have been converted to RST; only 21 to
go. There are various build improvements and the usual array of
documentation improvements and fixes.
-----BEGIN PGP SIGNATURE-----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=C5nd
-----END PGP SIGNATURE-----
Merge tag 'docs-4.11' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"A slightly quieter cycle for documentation this time around.
Three more DocBook template files have been converted to RST; only 21
to go. There are various build improvements and the usual array of
documentation improvements and fixes"
* tag 'docs-4.11' of git://git.lwn.net/linux: (44 commits)
docs / driver-api: Fix structure references in device_link.rst
PM / docs: Fix structure references in device.rst
Add a target to check broken external links in the Documentation
Documentation: Fix linux-api list typo
Documentation: DocBook/Makefile comment typo
Improve sparse documentation
Documentation: make Makefile.sphinx no-ops quieter
Documentation: DMA-ISA-LPC.txt
Documentation: input: fix path to input code definitions
docs: Remove the copyright year from conf.py
docs: Fix a warning in the Korean HOWTO.rst translation
PM / sleep / docs: Convert PM notifiers document to reST
PM / core / docs: Convert sleep states API document to reST
PM / core: Update kerneldoc comments in pm.h
doc-rst: Fix recursive make invocation from macros
doc-rst: Delete output of failed dot-SVG conversion
doc-rst: Break shell command sequences on failure
Documentation/sphinx: make targets independent of Sphinx work for HAVE_SPHINX=0
doc-rst: fixed cleandoc target when used with O=dir
Documentation/sphinx: prevent generation of .pyc files in the source tree
...
In order to clarify what the module actually does, and how to use it,
let's add some basic documentation to the kernel tree, together with
pointers to related specs and projects.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Acked-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Stash ctinfo 3-bit field into pointer to nf_conntrack object from
sk_buff so we only access one single cacheline in the conntrack
hotpath. Patchset from Florian Westphal.
2) Don't leak pointer to internal structures when exporting x_tables
ruleset back to userspace, from Willem DeBruijn. This includes new
helper functions to copy data to userspace such as xt_data_to_user()
as well as conversions of our ip_tables, ip6_tables and arp_tables
clients to use it. Not surprinsingly, ebtables requires an ad-hoc
update. There is also a new field in x_tables extensions to indicate
the amount of bytes that we copy to userspace.
3) Add nf_log_all_netns sysctl: This new knob allows you to enable
logging via nf_log infrastructure for all existing netnamespaces.
Given the effort to provide pernet syslog has been discontinued,
let's provide a way to restore logging using netfilter kernel logging
facilities in trusted environments. Patch from Michal Kubecek.
4) Validate SCTP checksum from conntrack helper, from Davide Caratti.
5) Merge UDPlite conntrack and NAT helpers into UDP, this was mostly
a copy&paste from the original helper, from Florian Westphal.
6) Reset netfilter state when duplicating packets, also from Florian.
7) Remove unnecessary check for broadcast in IPv6 in pkttype match and
nft_meta, from Liping Zhang.
8) Add missing code to deal with loopback packets from nft_meta when
used by the netdev family, also from Liping.
9) Several cleanups on nf_tables, one to remove unnecessary check from
the netlink control plane path to add table, set and stateful objects
and code consolidation when unregister chain hooks, from Gao Feng.
10) Fix harmless reference counter underflow in IPVS that, however,
results in problems with the introduction of the new refcount_t
type, from David Windsor.
11) Enable LIBCRC32C from nf_ct_sctp instead of nf_nat_sctp,
from Davide Caratti.
12) Missing documentation on nf_tables uapi header, from Liping Zhang.
13) Use rb_entry() helper in xt_connlimit, from Geliang Tang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 69b34fb996 ("netfilter: xt_LOG: add net namespace support for
xt_LOG") disabled logging packets using the LOG target from non-init
namespaces. The motivation was to prevent containers from flooding
kernel log of the host. The plan was to keep it that way until syslog
namespace implementation allows containers to log in a safe way.
However, the work on syslog namespace seems to have hit a dead end
somewhere in 2013 and there are users who want to use xt_LOG in all
network namespaces. This patch allows to do so by setting
/proc/sys/net/netfilter/nf_log_all_netns
to a nonzero value. This sysctl is only accessible from init_net so that
one cannot switch the behaviour from inside a container.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Packets arriving in a VRF currently are delivered to UDP sockets that
aren't bound to any interface. TCP defaults to not delivering packets
arriving in a VRF to unbound sockets. IP route lookup and socket
transmit both assume that unbound means using the default table and
UDP applications that haven't been changed to be aware of VRFs may not
function correctly in this case since they may not be able to handle
overlapping IP address ranges, or be able to send packets back to the
original sender if required.
So add a sysctl, udp_l3mdev_accept, to control this behaviour with it
being analgous to the existing tcp_l3mdev_accept, namely to allow a
process to have a VRF-global listen socket. Have this default to off
as this is the behaviour that users will expect, given that there is
no explicit mechanism to set unmodified VRF-unaware application into a
default VRF.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some double words found in Documentation.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Previous patches have moved the temperature sensor code into the
Marvell PHYs. A few now dead references to NET_DSA_HWMON were left
behind. Go reap them.
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add net.ipv4.ip_unprivileged_port_start, which is a per namespace sysctl
that denotes the first unprivileged inet port in the namespace. To
disable all privileged ports set this to zero. It also checks for
overlap with the local port range. The privileged and local range may
not overlap.
The use case for this change is to allow containerized processes to bind
to priviliged ports, but prevent them from ever being allowed to modify
their container's network configuration. The latter is accomplished by
ensuring that the network namespace is not a child of the user
namespace. This modification was needed to allow the container manager
to disable a namespace's priviliged port restrictions without exposing
control of the network namespace to processes in the user namespace.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thin stream DUPACK is to start fast recovery on only one DUPACK
provided the connection is a thin stream (i.e., low inflight). But
this older feature is now subsumed with RACK. If a connection
receives only a single DUPACK, RACK would arm a reordering timer
and soon starts fast recovery instead of timeout if no further
ACKs are received.
The socket option (THIN_DUPACK) is kept as a nop for compatibility.
Note that this patch does not change another thin-stream feature
which enables linear RTO. Although it might be good to generalize
that in the future (i.e., linear RTO for the first say 3 retries).
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
