Regression introduced with 8.4.5
drbd: application writes may set-in-sync in protocol != C
Overwriting the same block (LBA) while a former version is still
"in-flight" to the peer (to be exact: we did not receive the
P_BARRIER_ACK for its epoch yet) would wait for the full epoch of that
former version to be acknowledged by the peer.
In synchronous and quasi-synchronous protocols C and B,
this may double the latency on overwrites.
With protocol A, which is supposed to be asynchronous and only wait for
local completion, it is even worse: it would make overwrites
quasi-synchronous, they would be hit by the full RTT, which protocol A
was specifically meant to avoid, and possibly the additional time it
takes to drain the buffers first.
Particularly bad for databases, or anything else that
does frequent updates to the same blocks (various file system meta data).
No impact if >= rtt passes between updates to the same block.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If thinly provisioned volumes are used, during a resync the sync source
tries to find out if a block is deallocated. If it is deallocated, then
the resync target uses block_dev_issue_zeroout() on the range in
question.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As long as the value is 0 the feature is disabled. With setting
it to a positive value, DRBD limits and aligns its resync requests
to the rs-discard-granularity setting. If the sync source detects
all zeros in such a block, the resync target discards the range
on disk.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If during resync we read only zeroes for a range of sectors assume
that these secotors can be discarded on the sync target node.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When leaving resync states because of disconnect,
do the bitmap write-out synchronously in the drbd_disconnected() path.
When leaving resync states because we go back to AHEAD/BEHIND, or
because resync actually finished, or some disk was lost during resync,
trigger the write-out from after_state_ch().
The bitmap write-out for resync -> ahead/behind was missing completely before.
Note that this is all only an optimization to avoid double-resyncs of
already completed blocks in case this node crashes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The intention was to only suspend IO if some normal bitmap operation is
supposed to be locked out, not always. If the bulk operation is flaged
as BM_LOCKED_CHANGE_ALLOWED, we do not need to suspend IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use BIO_MAX_PAGES instead and we will remove BIO_MAX_SIZE.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have drbd
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull networking updates from David Miller:
"Highlights:
1) Support SPI based w5100 devices, from Akinobu Mita.
2) Partial Segmentation Offload, from Alexander Duyck.
3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.
4) Allow cls_flower stats offload, from Amir Vadai.
5) Implement bpf blinding, from Daniel Borkmann.
6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
actually using FASYNC these atomics are superfluous. From Eric
Dumazet.
7) Run TCP more preemptibly, also from Eric Dumazet.
8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
driver, from Gal Pressman.
9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.
10) Improve BPF usage documentation, from Jesper Dangaard Brouer.
11) Support tunneling offloads in qed, from Manish Chopra.
12) aRFS offloading in mlx5e, from Maor Gottlieb.
13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
Leitner.
14) Add MSG_EOR support to TCP, this allows controlling packet
coalescing on application record boundaries for more accurate
socket timestamp sampling. From Martin KaFai Lau.
15) Fix alignment of 64-bit netlink attributes across the board, from
Nicolas Dichtel.
16) Per-vlan stats in bridging, from Nikolay Aleksandrov.
17) Several conversions of drivers to ethtool ksettings, from Philippe
Reynes.
18) Checksum neutral ILA in ipv6, from Tom Herbert.
19) Factorize all of the various marvell dsa drivers into one, from
Vivien Didelot
20) Add VF support to qed driver, from Yuval Mintz"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
Revert "phy dp83867: Make rgmii parameters optional"
r8169: default to 64-bit DMA on recent PCIe chips
phy dp83867: Make rgmii parameters optional
phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
bpf: arm64: remove callee-save registers use for tmp registers
asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
switchdev: pass pointer to fib_info instead of copy
net_sched: close another race condition in tcf_mirred_release()
tipc: fix nametable publication field in nl compat
drivers: net: Don't print unpopulated net_device name
qed: add support for dcbx.
ravb: Add missing free_irq() calls to ravb_close()
qed: Remove a stray tab
net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fec-mpc52xx: use phydev from struct net_device
bpf, doc: fix typo on bpf_asm descriptions
stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
net: ethernet: fs-enet: use phydev from struct net_device
...
The attribute 0 is never used in drbd, so let's use it as pad attribute
in netlink messages. This minimizes the patch.
Note that this patch is only compile-tested.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly direct substitution with occasional adjustment or removing
outdated comments.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces uses of the long obsolete hash interface with
either shash (for non-SG users) or ahash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull final vfs updates from Al Viro:
- The ->i_mutex wrappers (with small prereq in lustre)
- a fix for too early freeing of symlink bodies on shmem (they need to
be RCU-delayed) (-stable fodder)
- followup to dedupe stuff merged this cycle
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: abort dedupe loop if fatal signals are pending
make sure that freeing shmem fast symlinks is RCU-delayed
wrappers for ->i_mutex access
lustre: remove unused declaration
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
parallel to mutex_{lock,unlock,trylock,is_locked,lock_nested},
inode_foo(inode) being mutex_foo(&inode->i_mutex).
Please, use those for access to ->i_mutex; over the coming cycle
->i_mutex will become rwsem, with ->lookup() done with it held
only shared.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In case the lower level device size changed, but some other internal
details of the resize did not work out, drbd_determine_dev_size() would
try to restore the previous settings, trusting
drbd_md_set_sector_offsets() to "do the right thing", but overlooked
that this internally may set the meta data base offset based on device size.
This could end up with incomplete on-disk meta data layout change, and
ultimately lead to data corruption (if the failure was not noticed or
ignored by the operator, and other things go wrong as well).
Just remember all meta data related offsets/sizes,
and on error restore them all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
During handshake communication, we also reconsider our device size,
using drbd_determine_dev_size(). Just in case we need to change the
offsets or layout of our on-disk metadata, we lock out application
and other meta data IO, and wait for the activity log to be "idle"
(no more referenced extents).
If this handshake happens just after a connection loss, with a fencing
policy of "resource-and-stonith", we have frozen IO.
If, additionally, the activity log was "starving" (too many incoming
random writes at that point in time), it won't become idle, ever,
because of the frozen IO, and this would be a lockup of the receiver
thread, and consquentially of DRBD.
Previous logic (re-)initialized with a special "empty" transaction
block, which required the activity log to fully drain first.
Instead, write out some standard activity log transactions.
Using lc_try_lock_for_transaction() instead of lc_try_lock() does not
care about pending activity log references, avoiding the potential
deadlock.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
To be able to "force out" an activity log transaction,
even if there are no pending updates.
This will be used to relocate the on-disk activity log,
if the on-disk offsets have to be changed,
without the need to empty the activity log first.
While at it, move the definition,
so we can drop the forward declaration of a static helper.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid to prematurely resume application IO: don't set/clear a single
bit, but inc/dec an atomic counter.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't remember a DRBD request as ack_pending, if it is not.
In protocol A, we usually clear RQ_NET_PENDING at the same time we set
RQ_NET_SENT, so when deciding to remember it as ack_pending,
mod_rq_state needs to look at the current request state,
not at the previous state before the current modification was applied.
This should prevent advance_conn_req_ack_pending() from walking the full
transfer log just to find NULL in protocol A, which would cause serious
performance degradation with many "in-flight" requests, e.g. when
working via DRBD-proxy, or with a huge bandwidth-delay product.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
new_disk_conf could be leaked if the follow on checks fail,
so make sure to free it on error if it was not assigned yet.
Found with smatch.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Disconnect should wait for pending bitmap IO.
But if that bitmap IO is not happening, because it is waiting for
pending application IO, and there is no progress, because the fencing
policy suspended application IO because of the disconnect,
then we deadlock.
The bitmap writeout in this case does not care for concurrent
application IO, so there is no point waiting for it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
lsblk should be able to pick up stacking device driver relations
involving DRBD conveniently.
Even though upstream kernel since 2011 says
"DON'T USE THIS UNLESS YOU'RE ALREADY USING IT."
a new user has been added since (bcache),
which sets the precedences for us to use it as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We cannot possibly support SECDISCARD, even if all backend devices would
support it: if our peer is currently unreachable, some instance of the
data may obviously still be recoverable.
We did not set discard_granularity at all. We don't really care (yet),
we only pass them on, so for now, set our granularity to one sector.
blkdev_stack_limits() takes care of the rest.
If we decide we cannot support discards,
not only clear the (not user visible) QUEUE_FLAG_DISCARD,
but set both (user visible) discard_granularity and max_discard_sectors
to zero, to avoid confusion with e.g. lsblk -D.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When accessing out meta data area on disk, we double check the
plausibility of the requested sector offsets, and are very noisy about
it if they look suspicious.
During initial read of our "superblock", for "external" meta data,
this triggered because the range estimate returned by
drbd_md_last_sector() was still wrong.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Suggested by Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Apparently we now implicitly get definitions for BITS_PER_PAGE and
BITS_PER_PAGE_MASK from the pid_namespace.h
Instead of renaming our defines, I chose to define only if not yet
defined, but to double check the value if already defined.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since kernel 3.3, we can use snprintf-style arguments
to create a workqueue.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The effective data generation ID may be interesting for debugging
purposes of scenarios involving diskless states.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In a multiple error scenario, we may end up with a "frozen" Primary,
that has no access to any data (no local disk, no replication link).
If we then resume-io, we try to generate a new data generation id,
which will fail if there is no longer a local disk.
Double check for available local data,
which prevents the NULL pointer deref.
If we are diskless, turn the resume-io in this situation
into the first stage of a "force down", by bumping the "effective" data
gen id, which will prevent later attach or connect to the former data
set without first being demoted (deconfigured).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The intention is to reduce CPU utilization. Recent measurements
unveiled that the current performance bottleneck is CPU utilization
on the receiving node. The asender thread became CPU limited.
One of the main points is to eliminate the idr_for_each_entry() loop
from the sending acks code path.
One exception in that is sending back ping_acks. These stay
in the ack-receiver thread. Otherwise the logic becomes too
complicated for no added value.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This prepares the next patch where the sending on the meta (or
control) socket is moved to a dedicated workqueue.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A D_FAILED disk transitions as quickly as possible to
D_DISKLESS. But in the "unresponsive local disk" case,
there remains a time window where a administrative detach command could
find the disk already failed, but some internal meta data IO against the
unresponsive local disk still pending.
In that case, drbd_md_get_buffer() will return NULL.
Don't unconditionally call drbd_md_put_buffer(), or it will cause
refcount imbalance, and prevent any further re-attach on this volume
(until it is deleted and re-created).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The recent (not yet released) backport of the extended state broadcasts
to support the "events2" subcommand of drbdsetup had some glitches.
remember_old_state() would first count all connections with a
net_conf != NULL, then allocate a suitable array, then populate that
array with all connections found to have net_conf != NULL.
This races with the state change to C_STANDALONE,
and the NULL assignment there.
remember_new_state() then iterates over said connection array,
assuming that it would be fully populated.
But rcu_lock() just makes sure the thing some pointer points to,
if any, won't go away. It does not make the pointer itself immutable.
In fact there is no need to "filter" connections based on whether or not
they have a currently valid configuration. Just record them always, if
they don't have a config, that's fine, there will be no change then.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Don't blame the peer for being unresponsive,
if we did not even ask the question yet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The only way to make DRBD intentionally call panic is to
set a disk timeout, have that trigger, "abort" some request and complete
to upper layers, then have the backend IO subsystem later complete these
requests successfully regardless.
As the attached IO pages have been recycled for other purposes
meanwhile, this will cause unexpected random memory changes.
To prevent corruption, we rather panic in that case.
Make it obvious from stack traces that this was the case by introducing
drbd_panic_after_delayed_completion_of_aborted_request().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Even though we really want to get the state information about our bad
disk to the peer as soon as possible, it is useful to first call the
local-io-error handler.
People may chose to hard-reset the box from there.
If that looks and behaves exactly like a "regular node crash", without
bumping the data generation UUIDs on the peer in between, it makes it
easier to deal with.
If you intend to return from the local-io-error handler, then better
return as quickly as possible to avoid triggering other timeouts.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If for some reason the primary lost its disk *and* the replication link
before it is able to communicate the disk loss, probably blocked IO,
then later is able to re-establish the connection, the peer needs to
bump its UUIDs just like it does when peer only loses the disk
and is able to communicate this in time.
Otherwise, a later re-attach of the disk on the primary may start a
resync in the "wrong" direction.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When detaching, we make sure no application IO is in-flight
by internally suspending IO, then trigger the state change,
wait for the result, and finally internally resume IO again.
Once we triggered the stat change to "Failed",
we expect it to change from Failed to Diskless.
(To avoid races, we actually wait for it to leave "Failed").
On an unresponsive local IO backend, this may not happen, ever.
Don't have a "hung" detach block IO "forever", but resume IO
before waiting for the state change to Diskless.
We may well be able to continue IO to and from a healthy peer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
(You should not use disk-timeout anyways,
see the man page for why...)
We add incoming requests to the tail of some ring list.
On local completion, requests are removed from that list.
The timer looks only at the head of that ring list,
so is supposed to only see the oldest request.
All protected by a spinlock.
The request object is created with timestamps zeroed out.
The timestamp was only filled in just before the actual submit.
But to actually submit the request, we need to give up the spinlock.
If you are unlucky, there is no older still pending request, the timer
looks at a new request with timestamp still zero (before it even was
submitted), and 0 + timeout is most likely older than "now".
Better assign the timestamp right when we put the
request object on said ring list.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
GFP_NOWAIT has a value of 0. I.e. functionality not changed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The lc_destroy() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The status command originates the drbd9 code base. While for now we
keep the status information in /proc/drbd available, this commit
allows the user base to gracefully migrate their monitoring
infrastructure to the new status reporting interface.
In drbd9 no status information is exposed through /proc/drbd.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The events2 command originates from drbd-9 development. It features
more information but requires a incompatible change in output
format.
Therefore the previous events command continues to exist, the new
improved events2 command becomes available now.
This prepares the user-base for a later switch to the complete
drbd9 code base.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of using a rwlock for synchronizing state changes across
resources, take the request locks of all resources for global state
changes. Use resources_mutex to serialize global state changes.
This means that taking the request lock of a resource is now enough to
prevent changes of that resource. (Previously, a read lock on the
global state lock was needed as well.)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Also change the enum values to all-capital letters.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is no need to have these two as inline functions. In addition,
drbd_should_send_out_of_sync() is only used in a single place, anyway.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In drbd-8.4 there is always a single connection per resource,
and there is always exactly one peer_device for a device.
peer_device can not be NULL here.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block IO poll support from Jens Axboe:
"Various groups have been doing experimentation around IO polling for
(really) fast devices. The code has been reviewed and has been
sitting on the side for a few releases, but this is now good enough
for coordinated benchmarking and further experimentation.
Currently O_DIRECT sync read/write are supported. A framework is in
the works that allows scalable stats tracking so we can auto-tune
this. And we'll add libaio support as well soon. Fow now, it's an
opt-in feature for test purposes"
* 'for-4.4/io-poll' of git://git.kernel.dk/linux-block:
direct-io: be sure to assign dio->bio_bdev for both paths
directio: add block polling support
NVMe: add blk polling support
block: add block polling support
blk-mq: return tag/queue combo in the make_request_fn handlers
block: change ->make_request_fn() and users to return a queue cookie
Merge second patch-bomb from Andrew Morton:
- most of the rest of MM
- procfs
- lib/ updates
- printk updates
- bitops infrastructure tweaks
- checkpatch updates
- nilfs2 update
- signals
- various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc,
dma-debug, dma-mapping, ...
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits)
ipc,msg: drop dst nil validation in copy_msg
include/linux/zutil.h: fix usage example of zlib_adler32()
panic: release stale console lock to always get the logbuf printed out
dma-debug: check nents in dma_sync_sg*
dma-mapping: tidy up dma_parms default handling
pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode
kexec: use file name as the output message prefix
fs, seqfile: always allow oom killer
seq_file: reuse string_escape_str()
fs/seq_file: use seq_* helpers in seq_hex_dump()
coredump: change zap_threads() and zap_process() to use for_each_thread()
coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP
signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT)
signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread()
signal: turn dequeue_signal_lock() into kernel_dequeue_signal()
signals: kill block_all_signals() and unblock_all_signals()
nilfs2: fix gcc uninitialized-variable warnings in powerpc build
nilfs2: fix gcc unused-but-set-variable warnings
MAINTAINERS: nilfs2: add header file for tracing
nilfs2: add tracepoints for analyzing reading and writing metadata files
...
No functional changes in this patch, but it prepares us for returning
a more useful cookie related to the IO that was queued up.
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
__GFP_WAIT was used to signal that the caller was in atomic context and
could not sleep. Now it is possible to distinguish between true atomic
context and callers that are not willing to sleep. The latter should
clear __GFP_DIRECT_RECLAIM so kswapd will still wake. As clearing
__GFP_WAIT behaves differently, there is a risk that people will clear the
wrong flags. This patch renames __GFP_WAIT to __GFP_RECLAIM to clearly
indicate what it does -- setting it allows all reclaim activity, clearing
them prevents it.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<linux/highmem.h> is the placace the get the kmap type flags, asm-generic
files are generic implementations only to be used by architecture code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The way the block layer is currently written, it goes to great lengths
to avoid having to split bios; upper layer code (such as bio_add_page())
checks what the underlying device can handle and tries to always create
bios that don't need to be split.
But this approach becomes unwieldy and eventually breaks down with
stacked devices and devices with dynamic limits, and it adds a lot of
complexity. If the block layer could split bios as needed, we could
eliminate a lot of complexity elsewhere - particularly in stacked
drivers. Code that creates bios can then create whatever size bios are
convenient, and more importantly stacked drivers don't have to deal with
both their own bio size limitations and the limitations of the
(potentially multiple) devices underneath them. In the future this will
let us delete merge_bvec_fn and a bunch of other code.
We do this by adding calls to blk_queue_split() to the various
make_request functions that need it - a few can already handle arbitrary
size bios. Note that we add the call _after_ any call to
blk_queue_bounce(); this means that blk_queue_split() and
blk_recalc_rq_segments() don't need to be concerned with bouncing
affecting segment merging.
Some make_request_fn() callbacks were simple enough to audit and verify
they don't need blk_queue_split() calls. The skipped ones are:
* nfhd_make_request (arch/m68k/emu/nfblock.c)
* axon_ram_make_request (arch/powerpc/sysdev/axonram.c)
* simdisk_make_request (arch/xtensa/platforms/iss/simdisk.c)
* brd_make_request (ramdisk - drivers/block/brd.c)
* mtip_submit_request (drivers/block/mtip32xx/mtip32xx.c)
* loop_make_request
* null_queue_bio
* bcache's make_request fns
Some others are almost certainly safe to remove now, but will be left
for future patches.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Jim Paris <jim@jtan.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md/md.c' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: skip more mq-based drivers, resolve merge conflicts, etc.]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some drivers use it now, others just set the limits field manually.
But in preparation for splitting this into a hard and soft limit,
ensure that they all call the proper function for setting the hw
limit for discards.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
Pull cgroup writeback support from Jens Axboe:
"This is the big pull request for adding cgroup writeback support.
This code has been in development for a long time, and it has been
simmering in for-next for a good chunk of this cycle too. This is one
of those problems that has been talked about for at least half a
decade, finally there's a solution and code to go with it.
Also see last weeks writeup on LWN:
http://lwn.net/Articles/648292/"
* 'for-4.2/writeback' of git://git.kernel.dk/linux-block: (85 commits)
writeback, blkio: add documentation for cgroup writeback support
vfs, writeback: replace FS_CGROUP_WRITEBACK with SB_I_CGROUPWB
writeback: do foreign inode detection iff cgroup writeback is enabled
v9fs: fix error handling in v9fs_session_init()
bdi: fix wrong error return value in cgwb_create()
buffer: remove unusued 'ret' variable
writeback: disassociate inodes from dying bdi_writebacks
writeback: implement foreign cgroup inode bdi_writeback switching
writeback: add lockdep annotation to inode_to_wb()
writeback: use unlocked_inode_to_wb transaction in inode_congested()
writeback: implement unlocked_inode_to_wb transaction and use it for stat updates
writeback: implement [locked_]inode_to_wb_and_lock_list()
writeback: implement foreign cgroup inode detection
writeback: make writeback_control track the inode being written back
writeback: relocate wb[_try]_get(), wb_put(), inode_{attach|detach}_wb()
mm: vmscan: disable memcg direct reclaim stalling if cgroup writeback support is in use
writeback: implement memcg writeback domain based throttling
writeback: reset wb_domain->dirty_limit[_tstmp] when memcg domain size changes
writeback: implement memcg wb_domain
writeback: update wb_over_bg_thresh() to use wb_domain aware operations
...
With the planned cgroup writeback support, backing-dev related
declarations will be more widely used across block and cgroup;
unfortunately, including backing-dev.h from include/linux/blkdev.h
makes cyclic include dependency quite likely.
This patch separates out backing-dev-defs.h which only has the
essential definitions and updates blkdev.h to include it. c files
which need access to more backing-dev details now include
backing-dev.h directly. This takes backing-dev.h off the common
include dependency chain making it a lot easier to use it across block
and cgroup.
v2: fs/fat build failure fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, a bdi (backing_dev_info) embeds single wb (bdi_writeback)
and the role of the separation is unclear. For cgroup support for
writeback IOs, a bdi will be updated to host multiple wb's where each
wb serves writeback IOs of a different cgroup on the bdi. To achieve
that, a wb should carry all states necessary for servicing writeback
IOs for a cgroup independently.
This patch moves bdi->state into wb.
* enum bdi_state is renamed to wb_state and the prefix of all enums is
changed from BDI_ to WB_.
* Explicit zeroing of bdi->state is removed without adding zeoring of
wb->state as the whole data structure is zeroed on init anyway.
* As there's still only one bdi_writeback per backing_dev_info, all
uses of bdi->state are mechanically replaced with bdi->wb.state
introducing no behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: drbd-dev@lists.linbit.com
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is long overdue, and is part of cleaning up how we allocate kernel
sockets that don't reference count struct net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
Mempools created for slab caches should use
mempool_create_slab_pool().
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
mempool_alloc() does not support __GFP_ZERO since elements may come from
memory that has already been released by mempool_free().
Remove __GFP_ZERO from mempool_alloc() in drbd_req_new() and properly
initialize it to 0.
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkdev_issue_discard() will zero a given block range. This is done by
way of explicit writing, thus provisioning or allocating the blocks on
disk.
There are use cases where the desired behavior is to zero the blocks but
unprovision them if possible. The blocks must deterministically contain
zeroes when they are subsequently read back.
This patch adds a flag to blkdev_issue_zeroout() that provides this
variant. If the discard flag is set and a block device guarantees
discard_zeroes_data we will use REQ_DISCARD to clear the block range. If
the device does not support discard_zeroes_data or if the discard
request fails we will fall back to first REQ_WRITE_SAME and then a
regular REQ_WRITE.
Also update the callers of blkdev_issue_zero() to reflect the new flag
and make sb_issue_zeroout() prefer the discard approach.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block layer driver updates from Jens Axboe:
- NVMe updates:
- The blk-mq conversion from Matias (and others)
- A stack of NVMe bug fixes from the nvme tree, mostly from Keith.
- Various bug fixes from me, fixing issues in both the blk-mq
conversion and generic bugs.
- Abort and CPU online fix from Sam.
- Hot add/remove fix from Indraneel.
- A couple of drbd fixes from the drbd team (Andreas, Lars, Philipp)
- With the generic IO stat accounting from 3.19/core, converting md,
bcache, and rsxx to use those. From Gu Zheng.
- Boundary check for queue/irq mode for null_blk from Matias. Fixes
cases where invalid values could be given, causing the device to hang.
- The xen blkfront pull request, with two bug fixes from Vitaly.
* 'for-3.19/drivers' of git://git.kernel.dk/linux-block: (56 commits)
NVMe: fix race condition in nvme_submit_sync_cmd()
NVMe: fix retry/error logic in nvme_queue_rq()
NVMe: Fix FS mount issue (hot-remove followed by hot-add)
NVMe: fix error return checking from blk_mq_alloc_request()
NVMe: fix freeing of wrong request in abort path
xen/blkfront: remove redundant flush_op
xen/blkfront: improve protection against issuing unsupported REQ_FUA
NVMe: Fix command setup on IO retry
null_blk: boundary check queue_mode and irqmode
block/rsxx: use generic io stats accounting functions to simplify io stat accounting
md: use generic io stats accounting functions to simplify io stat accounting
drbd: use generic io stats accounting functions to simplify io stat accounting
md/bcache: use generic io stats accounting functions to simplify io stat accounting
NVMe: Update module version major number
NVMe: fail pci initialization if the device doesn't have any BARs
NVMe: add ->exit_hctx() hook
NVMe: make setup work for devices that don't do INTx
NVMe: enable IO stats by default
NVMe: nvme_submit_async_admin_req() must use atomic rq allocation
NVMe: replace blk_put_request() with blk_mq_free_request()
...
Old backward-compat cruft
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A connection timeout affects all volumes of a resource!
Under the following conditions:
A resource with multiple volumes
AND
ko-count >=1
AND
a write request triggers the timeout (ko-count * timeout)
DRBD's internal state gets confused. That in turn may
lead to very miss leading follow up failures. E.g.
"BUG: scheduling while atomic"
CC: stable@kernel.org # v3.17
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This was not noticed for many years. Affects operation if
md raid is used a backing device for DRBD.
CC: stable@kernel.org # v3.2+
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If for some reason DRBD resync was the only activity on a backend
device, drbd_rs_c_min_rate_throttle() would mistakenly decide that it is
still initialization time, and keep throttling the resync.
This patch explicitly initializes ->rs_last_events to the current
backend event counters, and drops the rs_last_events == 0 from the
throttle condition.
Reported-by: Mikhail Sugakov <msugakov@amazon.de>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Symptoms:
If DRBD was "cleanly shut down" (all in sync, both Secondary before
disconnect, identical data generation uuids), and then one side was
promoted *during* the next connection handshake, the role change
could confuse the handshake.
The Primary would get stuck in WFBitmapS, the Secondary would log
unexpected cstate (Connected) in receive_bitmap
and get stuck in WFBitmapT.
Fix:
The test in is_valid_soft_transition wrong. It works because
the not allowed actions (promote/attach) do not touch the
cstate. The previous condition failed to demand a cstate change
in one clause.
In order to avoid deadlocks give up the state_mutex while waiting
for the transient state to go away.
Conflicts:
drbd/drbd_state.c
drbd/drbd_state.h
drbd/drbd_wrappers.h
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Avoid generic netlink calls in other parts of the code base.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The original code are the same as RB_DECLARE_CALLBACKS().
CC: Michel Lespinasse <walken@google.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 98683650 "Merge branch 'drbd-8.4_ed6' into
for-3.8-drivers-drbd-8.4_ed6" switches to the new augment API, but the
new API requires that the tree is augmented before rb_insert_augmented()
is called, which is missing.
So we add the augment-code to drbd_insert_interval() when it travels the
tree up to down before rb_insert_augmented(). See the example in
include/linux/interval_tree_generic.h or Documentation/rbtree.txt.
drbd_insert_interval() may cancel the insertion when traveling, in this
case, the just added augment-code does nothing before cancel since the
@this node is already in the subtrees in this case.
CC: Michel Lespinasse <walken@google.com>
CC: stable@kernel.org # v3.10+
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Was broken in 2010 with commit 4b0715f096
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The worker may now dequeue work items in batches.
This should reduce lock contention during busy periods.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Shorten receive path in the asender thread. Reduces CPU utilisation
of asender when receiving packets, and with that increases IOPs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This macro doesn't add any value; just use test_bit() instead.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These macros can easily be replaced with its definition.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
request_timer_fn() takes resource->req_lock via the device and releases it via
the connection. Avoid this as it is confusing static code checkers.
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
See "drbd/resources/*/volumes/*/resync_extents".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now they follow the _endio naming sheme.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Rename local variable 'ds' to 'disk_state' or 'data_size'.
'dgs' to 'digest_size'
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block driver changes from Jens Axboe:
"Nothing out of the ordinary here, this pull request contains:
- A big round of fixes for bcache from Kent Overstreet, Slava Pestov,
and Surbhi Palande. No new features, just a lot of fixes.
- The usual round of drbd updates from Andreas Gruenbacher, Lars
Ellenberg, and Philipp Reisner.
- virtio_blk was converted to blk-mq back in 3.13, but now Ming Lei
has taken it one step further and added support for actually using
more than one queue.
- Addition of an explicit SG_FLAG_Q_AT_HEAD for block/bsg, to
compliment the the default behavior of adding to the tail of the
queue. From Douglas Gilbert"
* 'for-3.17/drivers' of git://git.kernel.dk/linux-block: (86 commits)
bcache: Drop unneeded blk_sync_queue() calls
bcache: add mutex lock for bch_is_open
bcache: Correct printing of btree_gc_max_duration_ms
bcache: try to set b->parent properly
bcache: fix memory corruption in init error path
bcache: fix crash with incomplete cache set
bcache: Fix more early shutdown bugs
bcache: fix use-after-free in btree_gc_coalesce()
bcache: Fix an infinite loop in journal replay
bcache: fix crash in bcache_btree_node_alloc_fail tracepoint
bcache: bcache_write tracepoint was crashing
bcache: fix typo in bch_bkey_equal_header
bcache: Allocate bounce buffers with GFP_NOWAIT
bcache: Make sure to pass GFP_WAIT to mempool_alloc()
bcache: fix uninterruptible sleep in writeback thread
bcache: wait for buckets when allocating new btree root
bcache: fix crash on shutdown in passthrough mode
bcache: fix lockdep warnings on shutdown
bcache allocator: send discards with correct size
bcache: Fix to remove the rcu_sched stalls.
...
My static checker warns that "data_size" could be negative and underflow
the limit check. The code looks suspicious but I don't know if it is a
real bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Don't error out with misleading "out of memory"
if the cpu-mask has more bits set than there are CPUs.
Just truncate to nr_cpu_ids implicitly.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
size is always 4096,
page is always device->md_io.page.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
During resync, if we need to block some specific incoming write because
of active resync requests to that same range, we potentially caused
*all* new application writes (to "cold" activity log extents) to block
until this one request has been processed.
Improve the do_submit() logic to
* grab all incoming requests to some "incoming" list
* process this list
- move aside requests that are blocked by resync
- prepare activity log transactions,
- commit transactions and submit corresponding requests
- if there are remaining requests that only wait for
activity log extents to become free, stop the fast path
(mark activity log as "starving")
- iterate until no more requests are waiting for the activity log,
but all potentially remaining requests are only blocked by resync
* only then grab new incoming requests
That way, very busy IO on currently "hot" activity log extents cannot
starve scattered IO to "cold" extents. And blocked-by-resync requests
are processed once resync traffic on the affected region has ceased,
without blocking anything else.
The only blocking mode left is when we cannot start requests to "cold"
extents because all currently "hot" extents are actually used.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The data generation identifiers used to be exposed via sysfs
at /sys/block/drbdX/drbd/meta_data/data_gen_id (out-of-tree),
for advanced policy scripting.
Bring that information over to debugfs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Information of former /sys/block/drbdX/drbd/oldest_requests
is already with higher detail in these files:
debugfs/drbd/resource/$name/in_flight_summary,
debugfs/drbd/resource/$name/volumes/$vnr/oldest_requests
This patch adds
debugfs/drbd/resource/$name/connections/peer/oldest_requests
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make the first line of debugfs files a version number,
starting now with "v: 0".
If we change content of presentation, we will bump that.
Monitoring or diagnostic scritps that may parse these files
can then easily know when they need to be reviewed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Show oldest requests
* pending master bio completion and,
* if different, local disk bio completion.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Add a per-connection worker thread callback_history
with timing details, call site and callback function.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* Add details about pending meta data operations to in_flight_summary.
* Report number of requests waiting for activity log transactions.
* timing details of peer_requests to in_flight_summary.
* FLUSH details
DRBD devides the incoming request stream into "epochs",
in which peers are allowed to re-order writes independendly.
These epochs are separated by P_BARRIER on the replication link.
Such barrier packets, depending on configuration, may cause
the receiving side to drain the lower level device request queues
and call blkdev_issue_flush().
This is known to be an other major source of latency in DRBD.
Track timing details of calls to blkdev_issue_flush(),
and add them to in_flight_summary.
* data socket stats
To be able to diagnose bottlenecks and root causes of "slow" IO on DRBD,
it is useful to see network buffer stats along with the timing details of
requests, peer requests, and meta data IO.
* pending bitmap IO timing details to in_flight_summary.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Try to close the race between open() and debugfs_remove_recursive()
from inside an object destructor.
Once open succeeds, the object should stay around.
Open should not succeed if the object has already reached its destructor.
This may be overkill, but to make that happen, we check for existence of
a parent directory, "stale-ness" of "this" dentry, and serialize
kref_get_unless_zero() on the outermost object relevant for this file
with d_delete() on this dentry (using the parent's i_mutex).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To help diagnosing "high latency" or "hung" IO situations on DRBD,
present per drbd resource group a summary of operations currently in progress.
First item is a list of oldest drbd_request objects
waiting for various things:
* still being prepared
* waiting for activity log transaction
* waiting for local disk
* waiting to be sent
* waiting for peer acknowledgement ("receive ack", "write ack")
* waiting for peer epoch acknowledgement ("barrier ack")
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Add new debugfs hierarchy /sys/kernel/debug/
drbd/
resources/
$resource_name/connections/peer/$volume_number/
$resource_name/volumes/$volume_number/
minors/$minor_number -> ../resources/$resource_name/volumes/$volume_number/
Followup commits will populate this hierarchy with files containing
statistics, diagnostic information and some attribute data.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Track start and submit time of bitmap operations, and
add pending bitmap IO contexts to a new pending_bitmap_io list.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Initialize peer_request with timestamp and proper empty list head.
Add peer_request to list early, so debugfs can find this request and
report it as "preparing", even if we sleep before we actually submit it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To be able to present timing details in debugfs,
we need to track preparation/submit times of peer requests.
Track peer request flags early,
before they are put on the epoch_entry lists.
Waiting for activity log transactions may be a major latency factor.
We want to be able to present the peer_request state accurately in
debugfs, and what it is waiting for.
Consistently mark/unmark peer requests with EE_CALL_AL_COMPLETE_IO.
Set it only *after* calling drbd_al_begin_io(),
clear it as soon as we call drbd_al_complete_io().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Background resynchronisation does some "side-stepping", or throttles
itself, if it detects application IO activity, and the current resync
rate estimate is above the configured "cmin-rate".
What was not detected: if there is no application IO,
because it blocks on activity log transactions.
Introduce a new atomic_t ap_actlog_cnt, tracking such blocked requests,
and count non-zero as application IO activity.
This counter is exposed at proc_details level 2 and above.
Also make sure to release the currently locked resync extent
if we side-step due to such voluntary throttling.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
A request that is to be shipped to the peer goes through a few stages:
- queued
- sent, waiting for ack
- ack received, waiting for "barrier ack", which is re-order epoch being
closed on the peer by acknowledging a "cache flush" equivalent
on the lower level device.
In the later two stages, depending on protocol, we may have already
completed this request to the upper layers, so it won't be found anymore
on device->pending_master_completion[] lists.
Track the oldest request yet to be sent (req_next), the oldest not yet
acknowledged (req_ack_pending) and the oldest "still waiting for
something from the peer" (req_not_net_done), doing short list walks on
the transfer log to find the next pending one whenever such a request
makes progress.
Now we have a fast way to look up the oldest requests,
don't do a transfer log walk every time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Adding requests to per-device fifo lists as soon as possible after
allocating them leaves a simple list_first_entry_or_null() to find the
oldest request, regardless what it is still waiting for.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Record (in jiffies) how much time a request spends in which stages.
Followup commits will use and present this additional timing information
so we can better locate and tackle the root causes of latency spikes,
or present the backlog for asynchronous replication.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
For diagnostic purposes, track intent, start time
and latest submit time of meta data IO.
Move separate members from struct drbd_device
into the embeded struct drbd_md_io.
s/md_io_(page|in_use)/md_io.\1/
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_destroy_device means to give up reference counts
on the connection(s) reachable via the peer_device(s).
It must not do that by iterating via device->resource->connections,
resource and connections may have already been disassociated
by drbd_free_resource, and we'd leak connection refs.
Instead, iterate via device->peer_devices->connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now that we have additional asynchronous kref_get/kref_put
via debugfs, make sure we catch access after free.
Poison struct drbd_device, drbd_connection and drbd_resource
before kfree() with 0xfd, 0xfc, and 0xf2, respectively.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To be able to find and present such zero-out fallback peer_requests
in debugfs, we add those to "active_ee", once that list drained.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Keep the epoch entry lists (active_ee, read_ee, sync_ee, ...)
consistently "oldest first". That way finding the oldest not yet
successfully processed request is simply list_first_entry_or_null.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The only user of drbd_md_flush was bm_rw(),
and it is always followed by either a drbd_md_sync(),
or an al_write_transaction(), which, if so configured,
both end up submiting a FLUSH|FUA request anyways.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We sometimes do
if (list_empty(&w.list))
drbd_queue_work(&q, &w.list);
Removal (list_del_init) may happen outside all locks, after all
pending work entries have been moved to an on-stack local work list.
For not dynamically allocated, but embeded, work structs,
we must avoid to re-add until it really was removed.
Move that list_empty check inside the spin_lock(&q->q_lock)
within the helper function, and change to list_empty_careful().
This may have been the reason for a list_add corruption
inside drbd_queue_work().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We try to limit the number of "in-flight" resync requests.
One condition for that is the amount of requested data should not exceed
half of what can be covered by our "max-buffers" setting.
However we compared number of 4k pages with number of in-flight 512 Byte
sectors, and this extra throttle triggered much earlier than intended.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we lost a disk during the first resync after primary crash,
we could have prematurely cleared the CRASHED_PRIMARY flag.
Testing on C_CONNECTED is not what we meant there,
but testing for both peers to become D_UP_TO_DATE.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we throttle resync because the socket sendbuffer is filling up,
tell TCP about it, so it may expand the sendbuffer for us.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Just about all of these have been converted to __func__,
so convert the last uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we already "pulled ahead", we can short-circuit,
and avoid logging the same messages over and over again.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If "dirty" blocks are written to during resync,
that brings them in-sync.
By explicitly requesting write-acks during resync even in protocol != C,
we now can actually respect this.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In setups involving a DRBD-proxy and connections that experience a lot of
buffer-bloat it might be necessary to set ping-timeout to an
unusual high value. By default DRBD uses the same value to wait if a newly
established TCP-connection is stable. Since the DRBD-proxy is usually located
in the same data center such a long wait time may hinder DRBD's connect process.
In such setups socket-check-timeout should be set to
at least to the round trip time between DRBD and DRBD-proxy. I.e. in most
cases to 1.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Before the patch
'drbd: Keep the listening socket open while trying to connect to the peer'
the newly created socket inherited the receive timeout from the listen
socket. The listen socket had a receive timeout of connect-intervall
+- 30% random jitter.
The real issue is that after the mentioned patch we had no timeout at all.
Now use 4 times the ping-timeout.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Checksum based resync trades CPU cycles for network bandwidth,
in situations where we expect much of the to-be-resynced blocks
to be actually identical on both sides already.
In a "network hickup" scenario, it won't help:
all to-be-resynced blocks will typically be different.
The use case is for the resync of *potentially* different blocks
after crash recovery -- the crash recovery had marked larger areas
(those covered by the activity log) as need-to-be-resynced,
just in case. Most of those blocks will be identical.
This option makes it possible to configure checksum based resync,
but only actually use it for the first resync after primary crash.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
During handshake, we compare backend sizes, and user set limits,
and agree on what device size we are going to expose.
We remember that last-agreed-size in our meta data.
But if we come up diskless, we have to accept what the peer
presents us with. We used to accept the peers maximum potential
capacity (backend size), which is wrong, and could lead to IO errors
due to access beyond end of device.
Instead, we need to accept the peer's current size.
Unless that is communicated as 0, in which case we
accept the backend size, or the user set limit, if set.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We intentionally do not serialize /proc/drbd access with
internal state changes or statistic updates.
Because of that, cat /proc/drbd may race with resync just being
finished, still see the sync state, and find information about
number of blocks still to go, but then find the total number
of blocks within this resync has just been reset to 0
when accessing it.
This now produces bogus numbers in the resync speed estimates.
Fix by accessing all relevant data only once,
and fixing it up if "still to go" happens to be more than "total".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Get rid of dump_stack() debug statements.
There is no point whatsoever in registering and unregistering a reboot
notifier that doesn't do anything.
The intention was to switch to an "emergency read-only" mode,
so we won't have to resync the full activity log just because
we had been Primary before the reboot.
Once we have that implemented, we may re-introduce the reboot notifier.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The textual representation of resync extents in /proc/drbd presented
with proc_details >= 3 was wrong, it used bitnumbers as bitmasks.
It was not particularly useful either, and I doubt anyone has even tried
to look at it in the last few years. Drop it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last user was al_write_transaction, if called with "delegate",
and the last user to call it with "delegate = true" was the receiver
thread, which has no need to delegate, but can call it himself.
Finally drop the delegate parameter, drop the extra
w_al_write_transaction callback, and drop drbd_queue_work_front.
Do not (yet) change dequeue_work_item to dequeue_work_batch, though.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This replaces the md_sync_work member of struct drbd_device
by a new MD_SYNC "work bit" in device->flags.
This replaces the resync_start_work member of struct drbd_device
by a new RS_START "work bit" in device->flags.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The recent fix to put_ldev() (correct ordering of access to local_cnt
and state.disk; memory barrier in __drbd_set_state) guarantees
that the cleanup happens exactly once.
However it does not yet guarantee that the cleanup happens from worker
context, the last put_ldev() may still happen from atomic context,
which must not happen: blkdev_put() may sleep.
Fix this by scheduling the cleanup to the worker instead,
using a couple more bits in device->flags and a new helper,
drbd_device_post_work().
Generalized the "resync progress" work to cover these new work bits.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: bd_release+0x21/0x70
Process drbd_w_t7146
Call Trace:
close_bdev_exclusive
drbd_free_ldev [drbd]
drbd_ldev_destroy [drbd]
w_after_state_ch [drbd]
Race probably went like this:
state.disk = D_FAILED
... first one to hit zero during D_FAILED:
put_ldev() /* ----------------> 0 */
i = atomic_dec_return()
if (i == 0)
if (state.disk == D_FAILED)
schedule_work(go_diskless)
/* 1 <------ */ get_ldev_if_state()
go_diskless()
do_some_pre_cleanup() corresponding put_ldev():
force_state(D_DISKLESS) /* 0 <------ */ i = atomic_dec_return()
if (i == 0)
atomic_inc() /* ---------> 1 */
state.disk = D_DISKLESS
schedule_work(after_state_ch) /* execution pre-empted by IRQ ? */
after_state_ch()
put_ldev()
i = atomic_dec_return() /* 0 */
if (i == 0)
if (state.disk == D_DISKLESS) if (state.disk == D_DISKLESS)
drbd_ldev_destroy() drbd_ldev_destroy();
Trying to fix this by checking the disk state *before* the
atomic_dec_return(), which implies memory barriers, and by inserting
extra memory barriers around the state assignment in __drbd_set_state().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
For some reason we have assumed NOIDLE was implied
by one of the other flags we set. It is not (anymore?).
Explicitly set REQ_NOIDLE for synchronous meta data updates,
or we can seriously starve random writes when using CFQ.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This probably does not have any real life impact,
but we should first persist any potentially new UUID
and other meta data flags, as well as our new role,
before we allow/disallow write access.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This should reduce latency for such in-DRBD-protocol "pings",
and may help reduce spurious disconnect/reconnect cycles due to
"PingAck did not arrive in time."
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The conf_update mutex used to be held while clearing the
net_conf->discard_my_data flag inside drbd_set_role.
It was moved into drbd_adm_set_role with
drbd: allow parallel promote/demote actions
but then replaced at that location by the newly introduced adm_mutex with
drbd: Fix a potential deadlock in drbdsetup, introduce resource->adm_mutex
And I simply forgot to put it back in at the original location.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we re-write all meta data due to resize, we have open-coded write-out
of our meta data super block. Stop the md_sync_timer, it would just
trigger scary but in this case spurious "timer expired" messages.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This fixes one recent regresion,
and one long existing bug.
The bug:
drbd_try_clear_on_disk_bm() assumed that all "count" bits have to be
accounted in the resync extent corresponding to the start sector.
Since we allow application requests to cross our "extent" boundaries,
this assumption is no longer true, resulting in possible misaccounting,
scary messages
("BAD! sector=12345s enr=6 rs_left=-7 rs_failed=0 count=58 cstate=..."),
and potentially, if the last bit to be cleared during resync would
reside in previously misaccounted resync extent, the resync would never
be recognized as finished, but would be "stalled" forever, even though
all blocks are in sync again and all bits have been cleared...
The regression was introduced by
drbd: get rid of atomic update on disk bitmap works
For an "empty" resync (rs_total == 0), we must not "finish" the
resync on the SyncSource before the SyncTarget knows all relevant
information (sync uuid). We need to wait for the full round-trip,
the SyncTarget will then explicitly notify us.
Also for normal, non-empty resyncs (rs_total > 0), the resync-finished
condition needs to be tested before the schedule() in wait_for_work, or
it is likely to be missed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We may implicitly call drbd_send() from inside wait_for_work(),
via maybe_send_barrier().
If the "stop" signal was send just before that, drbd_send() would call
flush_signals(), and we would run an unbounded schedule() afterwards.
Fix: check for thread_state == RUNNING before we schedule()
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Just trigger the occasional lazy bitmap write-out during resync
from the central wait_for_work() helper.
Previously, during resync, bitmap pages would be written out separately,
synchronously, one at a time, at least 8 times each (every 512 bytes
worth of bitmap cleared).
Now we trigger "merge friendly" bulk write out of all cleared pages
every two seconds during resync, and once the resync is finished.
Most pages will be written out only once.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Previously, once you disabled flushes as a means of enforcing
write-ordering, you'd need to detach/re-attach to enable them again.
Allow drbdsetup disk-options to re-enable previously disabled
write-ordering policy options at runtime.
While at it fix RCU in drbd_bump_write_ordering()
max_allowed_wo() uses rcu_dereference, therefore it must
be called within rcu_read_lock()/rcu_read_unlock()
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Reduce the number of calls to first_peer_device(). Instead, call
first_peer_device() just once to assign a local variable peer_device.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Instead of dropping and re-aquiring the spinlock around the submit,
just remember that we want to submit, and do that only once we have
dropped the spinlock for good.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since the member of drbd_device is called ldev
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Some parts of the code assumed that get_ldev_if_state(device, D_ATTACHING)
is sufficient to access the ldev member of the device object. That was
wrong. ldev may not be there or might be freed at any time if the device
has a disk state of D_ATTACHING.
bm_rw()
Documented that drbd_bm_read() is only called from drbd_adm_attach.
drbd_bm_write() is only called when a reference is held, and it is
documented that a caller has to hold a reference before calling
drbd_bm_write()
drbd_bm_write_page()
Use get_ldev() instead of get_ldev_if_state(device, D_ATTACHING)
drbd_bmio_set_n_write()
No longer use get_ldev_if_state(device, D_ATTACHING). All callers
hold a reference to ldev now.
drbd_bmio_clear_n_write()
All callers where holding a reference of ldev anyways. Remove the
misleading get_ldev_if_state(device, D_ATTACHING)
drbd_reconsider_max_bio_size()
Removed the get_ldev_if_state(device, D_ATTACHING). All callers
now pass a struct drbd_backing_dev* when they have a proper
reference, or a NULL pointer.
Before this fix, the receiver could trigger a NULL pointer
deref when in drbd_reconsider_max_bio_size()
drbd_bump_write_ordering()
Used get_ldev_if_state(device, D_ATTACHING) with the wrong assumption.
Remove it, and allow the caller to pass in a struct drbd_backing_dev*
when the caller knows that accessing this bdev is safe.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since linux kernel 3.13, kthread_run() internally uses
wait_for_completion_killable(). We sometimes may use kthread_run()
while we still have a signal pending, which we used to kick our threads
out of potentially blocking network functions, causing kthread_run() to
mistake that as a new fatal signal and fail.
Fix: flush_signals() before kthread_run().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Discards don't have any payload.
But the scsi layer still expects a bio_vec it can use internally,
see sd_setup_discard_cmnd() and blk_add_request_payload().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If there are no peer_devices or connections, I'd rather have NULL
than some "arbitrary" address pretending to point to a struct.
Helps to avoid hard to debug symptoms, in case we ever try to use
and dereference a drbd_connection or drbd_peer_device
where we in fact don't have any connection at all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A newly created device was never exposed before, i.e. has a
exposed_data_uuid of 0. Then it is valid to attach to any current_uuid
of a backing device (of course also to a newly created one (4))
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In case a connection transitions into C_TIMEOUT within the timer
function (request_timer_fn()) we need to make sure that the receiver
thread (potentially running on a different CPU) sees the updated
cstate later on.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Just because it is the oldest not yet completed request
does not make it the oldest request waiting for disk.
Or waiting for the peer.
And we completely missed already completed requests
that would still hold references to activity log extents,
waiting only for the barrier ack.
Find two oldest not yet completely processed requests,
one that is still waiting for local completion,
and one that is still waiting for some response from the peer.
These may or may not be the same request object.
Then separately apply the network and disk timeouts, respectively.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In the implementation as it was, the two peers sent each other
a challenge, and expects the challenge hashed with the shared
secret back.
A attacker could simply wait for the challenge of the peer, and
send the same challenge back. Then it waits for the response, and
sends the same response back.
Prevent this by not accepting a challenge from the peer that is
the same as the challenge sent to the peer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Once our sender thread needs to wait_for_work(),
and actually needs to schedule(), just before we do that,
we already check if it is useful to implicitly close the last epoch.
The condition was too strict: only implicitly close the epoch,
if there have been no new (write) requests at all.
The assumption was that if there were new requests, they would
always be communicated one way or another, and would send necessary
epoch separating barriers explicitly.
This is not always true, e.g. when becoming diskless,
or while explicitly starting a full resync.
The last communicated epoch could stay open for a long time,
locking down corresponding activity log extents.
It is safe to always implicitly send that last barrier, as soon as we
determin that there cannot be more requests in the last communicated
epoch, even if there have been (uncommunicated) new requests in new
epochs meanwhile.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When batching more updates to the activity log into single transactions,
we lost the ability for new requests to force themselves into the active
set: all preparation steps became non-blocking, and if all currently
hot extents keep busy, they could starve out new incoming requests
to cold extents for quite a while.
This can only happen if your IO backend accepts more IO operations per
average DRBD replication round trip time than you have al-extents
configured.
If we have incoming requests to cold extents,
at least do one blocking update per transaction.
In an artificial worst-case workload on SSD with an asynchronous 600 ms
replication link, with al-extents = 7 (the minimum we allow), and
concurrent full resynch, without this patch, some write requests have
been observed to be starved for 40 seconds.
With this patch, application observed a worst case latency of twice the
replication round trip time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We want to store in persistent meta data what the peer DRBD can handle,
which, due to spreading requests to multiple bios,
may be more than its backing device can handle.
Otherwise, if a disconnected Primary temporarily loses access to its local data
as well, we may accidentally shrink the max-bio setting, portentially causing
already assembled, but not yet processed, application bios to be spuriously
failed due to device limits.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In the drbd make request function, specifically in
drbd_send_and_submit(), we decide whether we want to send the actual
write request, or only a "set this block out of sync" information.
We do so based on the current connection state, while holding the req_lock.
The connection state is not supposed to change while holding the req_lock.
But in drbd_start_resync, we did change that state anyways,
while only holding the global_state_lock, which is enough to change
sync-after dependencies (paused vs active resync), but
not good enough to change the connection state.
Fix: in drbd_start_resync, first grab the req_lock to serialize with
drbd_send_and_submit(), before grabbing the global_state_lock
to be able to evaluate the sync-after dependencies.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow the user of REQ_DISCARD.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Note that I do NOT call __drbd_chk_io_error for failed REQ_DISCARD.
That may be wrong, though, or needs to differ between EOPNOTSUPP and
other errors...
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the receiver needs to serve a discard request on a queue that does
not announce to be discard cabable, it falls back to do synchronous
blkdev_issue_zeroout().
We expect only "reasonably" large (up to one activity log extent?)
discard requests.
We do this to not to not block the receiver for too long in this
fallback code path, and to not set/clear too many bits inside one
spinlock_irq_save() in drbd_set_in_sync/drbd_set_out_of_sync,
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We plan to use genl_family->parallel_ops = true in the future,
but need to review all possible interactions first.
For now, only selectively drop genl_lock() in drbd_set_role(),
instead serializing on our own internal resource->conf_update mutex.
We now can be promoted/demoted on many resources in parallel,
which may significantly improve cluster failover times
when fencing is required.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Because all administrative requests via genetlink have been globally
serialized via genl_lock(), we used to have one static struct
drbd_config_context "admin context".
Move this on-stack to the respective callback functions.
This will allow us to selectively drop the genl_lock()
(or use genl_family->parallel_ops) in the future.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a 'cluster wide' disconnect executes, the result comes back
from the peer, and immediately after that the connection breaks
then _conn_rq_cond() reported back SS_CW_SUCCESS.
Therefore _conn_request_state() calls conn_set_state(), which
has a BUG() in it.
The BUG() is hit because conn_is_valid_transition() does not like
the transaction. Which goes back to is_valid_soft_transition()
returning SS_OUTDATE_WO_CONN.
This fix is to consider an error reported by is_valid_soft_transition()
even when the peer agreed to the transaction.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Before, application IO could pre-empt resync activity
for up to hardcoded 20 seconds per resync request.
A very busy server could throttle the effective resync bandwidth
down to one request per 20 seconds.
Now, we only let application IO pre-empt resync traffic
while the current resync rate estimate is above c-min-rate.
If you disable the c-min-rate throttle feature (set c-min-rate = 0),
application IO will no longer pre-empt resync traffic at all.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If max-buffers and socket buffer sizes are "too small" for the chosen
resync rate, this could lead potentially lead to a distributed deadlock,
which may or may not resolve itself via the "ko-count" and request
timeout mechanism, or could be resolved by forced disconnect.
One option to deal with this is proper configuration:
use larger max-buffer and socket buffers settings,
or reduce the resync rate.
But even with bad configuration we should not deadlock,
but "gracefully" recover.
The issue is avoided by using only up to max-buffers/2 for resync
requests, and by using max-buffers not as a hard limit for data buffer
allocations, but as a throttle threshold only.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
While merging adjacent dirty blocks into resync requests,
the resync rate throttle was disregarded.
For very low resync rates, the effective rate may have exceeded
the intended rate by a larger margin.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If we don't make resync or verify progress for "too long",
we want to flag it as "stalled".
Since 2010, "use rolling marks for resync speed calculation"
this "too long" was wrong by a factor of HZ.
With HZ 250, it would have been flagged as stalled
after 100 minutes.
Hardcode 3 minutes instead.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a user forces the operation he takes the blame in case
the peer does not have enough space. No reason to dey this...
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Actually we are clearing the susp_fen flag if we are not going
to call a fencing handler.
For setting the susp_fen flag needs to be edge-triggerd, and not
level triggered.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When we need to outdate the peer while being promoted to primary,
and the connection gets established at the same time, we deadlock
in drbd_try_outdate_peer() when trying to clear the susp_fen
bit.
Fix this by setting the STATE_SENT bit while holding the mutex.
Using drbd_change_state(.. , CS_HARD, ..) which does not block
until STATE_SENT is cleared, is only for clearness. It does
not contribute anything to the fix.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
Right now every resource has exactly one connection. But we are preparing
for dynamic connections. I.e. in the future thre can be resources without
connections.
However smatch points this out as 'variable dereferenced before check',
which is correct.
This issue was introduced in
drbd: get_one_status(): Iterate over resource->devices instead of connection->peer_devices
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In the drbd_thread "infrastructure" functions, only use the resource instead of
the connection. Make the connection field of drbd_thread optional. This will
allow to introduce threads which are not associated with a connection.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
in w_e_ (peer request) callbacks and in peer request I/O completion handlers
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
These functions are not used as drbd_work callbacks.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
The new function can flush any work queue, not just the work queue of the data
socket of a connection.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
