Following patch changes vport->send return type so that vport
layer can do error accounting.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
The get_config vport op is left over from old compatibility code,
it is neither used nor implemented any more.
Signed-off-by: Jesse Gross <jesse@nicira.com>
It is an error to try to change the type of a vport using the set
command. However, while we check that this is an error, we still
proceed to allocate memory which then gets freed immediately.
This stops processing after noticing the error, which does not
actually fix a bug but is more correct.
Signed-off-by: Jesse Gross <jesse@nicira.com>
The WKS (Well Known Services) bitmask should be transmitted in big endian
order. Picky implementations will refuse to establish an LLCP link when the
WKS bit 0 is not set to 1. The vast majority of implementations out there
are not that picky though...
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to advertise our LLCP support properly and to follow the LLCP
specs requirements, we need to initialize the WKS (Well-Known Services)
bitfield to 1 as SAP 0 is the only mandatory supported service.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When we receive a RNR, the remote is busy processing the last received
frame. We set a local flag for that, and we should send a SYMM when it
is set instead of sending any pending frame.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Without the new LLCP_CONNECTING state, non blocking sockets will be
woken up with a POLLHUP right after calling connect() because their
state is stuck at LLCP_CLOSED.
That prevents userspace from implementing any proper non blocking
socket based NFC p2p client.
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In nfc_llcp_tx_work() the sk_buff is not freed when the llcp_sock
is null and the PDU is an I one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch keeps the socket alive and therefore does not remove
it from the sockets list in the local until the DISC PDU has been
actually sent. Otherwise we would reply with DM PDUs before sending
the DISC one.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
nfc_llcp_send_disconnect() already exists but is not used.
nfc_llcp_disconnect() naming is not consistent with other PDU
sending functions.
This patch removes nfc_llcp_send_disconnect() and renames
nfc_llcp_disconnect()
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enabling or disabling an NFC accessible secure element through netlink
requires giving both an NFC controller and a secure element indexes.
Once enabled the secure element will handle card emulation once polling
starts.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Called via netlink, this API will enable or disable a specific secure
element. When a secure element is enabled, it will handle card emulation
and more generically ISO-DEP target mode, i.e. all target mode cases
except for p2p target mode.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an NFC driver or host controller stack discovers a secure element,
it will call nfc_add_se(). In order for userspace applications to use
these secure elements, a netlink event will then be sent with the SE
index and its type. With that information userspace applications can
decide wether or not to enable SEs, through their indexes.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API will allow NFC drivers to add and remove the secure elements
they know about or detect. Typically this should be called (asynchronously
or not) from the driver or the host interface stack detect_se hook.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Secure elements need to be discovered after enabling the NFC controller.
This is typically done by the NCI core and the HCI drivers (HCI does not
specify how to discover SEs, it is left to the specific drivers).
Also, the SE enable/disable API explicitely takes a SE index as its
argument.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Supported secure elements are typically found during a discovery process
initiated when the NFC controller is up and running. For a given NFC
chipset there can be many configurations (embedded SE or not, with or
without a SIM card wired to the NFC controller SWP interface, etc...) and
thus driver code will never know before hand which SEs are available.
So we remove this field, it will be replaced by a real SE discovery
mechanism.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.
A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()
Payload is passed to NCI module.
At the end, driver interruption is re asserted.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.
A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
After data has been sent, driver interruption is re-asserted.
If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).
This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).
NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In commit 2f94aabd9f
(refactor sctp_outq_teardown to insure proper re-initalization)
we modified sctp_outq_teardown to use sctp_outq_init to fully re-initalize the
outq structure. Steve West recently asked me why I removed the q->error = 0
initalization from sctp_outq_teardown. I did so because I was operating under
the impression that sctp_outq_init would properly initalize that value for us,
but it doesn't. sctp_outq_init operates under the assumption that the outq
struct is all 0's (as it is when called from sctp_association_init), but using
it in __sctp_outq_teardown violates that assumption. We should do a memset in
sctp_outq_init to ensure that the entire structure is in a known state there
instead.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: "West, Steve (NSN - US/Fort Worth)" <steve.west@nsn.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: netdev@vger.kernel.org
CC: davem@davemloft.net
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink directives and ndo entry to allow for controling
VF link, which can be in one of three states:
Auto - VF link state reflects the PF link state (default)
Up - VF link state is up, traffic from VF to VF works even if
the actual PF link is down
Down - VF link state is down, no traffic from/to this VF, can be of
use while configuring the VF
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
htb_class structures are big, and source of false sharing on SMP.
By carefully splitting them in two parts, we can improve performance.
I got 9 % performance increase on a 24 threads machine, with 200
concurrent netperf in TCP_RR mode, using a HTB hierarchy of 4 classes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Caught by sparse:
- __rcu: missing annotation to sd->flow_limit
- __user: direct access in cpumask_scnprintf
Also
- add endline character when printing bitmap if room in buffer
- avoid bucket overflow by reducing FLOW_LIMIT_HISTORY
The last item warrants some explanation. The hashtable buckets are
subject to overflow if FLOW_LIMIT_HISTORY is larger than or equal
to bucket size, since all packets may end up in a single bucket. The
current (rather arbitrary) history value of 256 happens to match the
buffer size (u8).
As a result, with a single flow, the first 128 packets are accepted
(correct), the second 128 packets dropped (correct) and then the
history[] array has filled, so that each subsequent new packet
causes an increment in the bucket for new_flow plus a decrement
for old_flow: a steady state.
This is fine if packets are dropped, as the steady state goes away
as soon as a mix of traffic reappears. But, because the 256th packet
overflowed the bucket to 0: no packets are dropped.
Instead of explicitly adding an overflow check, this patch changes
FLOW_LIMIT_HISTORY to never be able to overflow a single bucket.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
(first item)
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a simple forward to the HCI driver. When driver is done with the
operation, it shall directly notify NFC Core by calling
nfc_fw_upload_done().
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As several NFC chipsets can have their firmwares upgraded and
reflashed, this patchset adds a new netlink command to trigger
that the driver loads or flashes a new firmware. This will allows
userspace triggered firmware upgrade through netlink.
The firmware name or hint is passed as a parameter, and the driver
will eventually fetch the firmware binary through the request_firmware
API.
The cmd can only be executed when the nfc dev is not in use. Actual
firmware loading/flashing is an asynchronous operation. Result of the
operation shall send a new event up to user space through the nfc dev
multicast socket. During operation, the nfc dev is not openable and
thus not usable.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.
Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.
NfcWilink driver is also updated to use those functions.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Even though the HCI_Delete_Stored_Link_Key command is mandatory for 1.1
and later controllers some controllers do not seem to support it
properly as was witnessed by one Broadcom based controller:
< HCI Command: Delete Stored Link Key (0x03|0x0012) plen 7
bdaddr 00:00:00:00:00:00 all 1
> HCI Event: Command Complete (0x0e) plen 4
Delete Stored Link Key (0x03|0x0012) ncmd 1
status 0x11 deleted 0
Error: Unsupported Feature or Parameter Value
Luckily this same controller also doesn't list the command in its
supported commands bit mask (counting from 0 bit 7 of octet 6):
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
status 0x00
Commands: ffffffffffff1ffffffffffff30fffff3f
Therefore, it makes sense to move sending of HCI_Delete_Stored_Link_Key
to after receiving the supported commands response and to only send it
if its respective bit in the mask is set. The downside of this is that
we no longer send the HCI_Delete_Stored_Link_Key command for Bluetooth
1.1 controllers since HCI_Read_Local_Supported_Command was introduced in
version 1.2, but this is an acceptable penalty as the command in
question shouldn't affect critical behavior.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If CONFIG_NET_NS is not set then __net_init is the same as __init and
__net_exit is the same as __exit. These functions will be removed from
memory after the module loads or is removed. Functions that are exported
for use by other functions should never be labeled for removal.
Bug introduced by commit c544193214
("GRE: Refactor GRE tunneling code.")
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the AP's beacon rate in the scan BSS data and in the
interface configuration to let the drivers know which rate
the AP is using. This information may be used by drivers,
in our case to let the firmware optimise beacon RX.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If users apply shaper to vti tunnel then it will cause a kernel crash. The
problem seems to be due to the vti_tunnel_xmit function not clearing
skb->opt field before passing the packet to xfrm tunneling code.
Signed-off-by: Saurabh Mohan <saurabh@vyatta.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux sends new unset data during disorder and recovery state if all
(suspected) lost packets have been retransmitted ( RFC5681, section
3.2 step 1 & 2, RFC3517 section 4, NexSeg() Rule 2). One requirement
is to keep the receive window about twice the estimated sender's
congestion window (tcp_rcv_space_adjust()), assuming the fast
retransmits repair the losses in the next round trip.
But currently it's not the case on the first round trip in either
normal or Fast Open connection, beucase the initial receive window
is identical to (expected) sender's initial congestion window. The
fix is to double it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPPoL2TP sockets should comply with the standard send*() return values
(i.e. return number of bytes sent instead of 0 upon success).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy user data after PPP framing header. This prevents erasure of the
added PPP header and avoids leaking two bytes of uninitialised memory
at the end of skb's data buffer.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the uses of this unnecessary typedef.
Done via perl script:
$ git grep --name-only -w ctl_table net | \
xargs perl -p -i -e '\
sub trim { my ($local) = @_; $local =~ s/(^\s+|\s+$)//g; return $local; } \
s/\b(?<!struct\s)ctl_table\b(\s*\*\s*|\s+\w+)/"struct ctl_table " . trim($1)/ge'
Reflow the modified lines that now exceed 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since team functionality relies heavily on userspace daemon, we need to
deliver event to userspace via Netlink as quick as possible. So make all
team port device link events urgent.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
uaddr->sa_data is exactly of size 14, which is hard-coded here and
passed as a size argument to strncpy(). A device name can be of size
IFNAMSIZ (== 16), meaning we might leave the destination string
unterminated. Thus, use strlcpy() and also sizeof() while we're
at it. We need to memset the data area beforehand, since strlcpy
does not padd the remaining buffer with zeroes for user space, so
that we do not possibly leak anything.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/ping.c:286:5: sparse: symbol 'ping_check_bind_addr' was not declared. Should it be static?
net/ipv4/ping.c:355:6: sparse: symbol 'ping_set_saddr' was not declared. Should it be static?
net/ipv4/ping.c:370:6: sparse: symbol 'ping_clear_saddr' was not declared. Should it be static?
net/ipv6/ping.c:60:5: sparse: symbol 'dummy_ipv6_recv_error' was not declared. Should it be static?
net/ipv6/ping.c:64:5: sparse: symbol 'dummy_ip6_datagram_recv_ctl' was not declared. Should it be static?
net/ipv6/ping.c:69:5: sparse: symbol 'dummy_icmpv6_err_convert' was not declared. Should it be static?
net/ipv6/ping.c:73:6: sparse: symbol 'dummy_ipv6_icmp_error' was not declared. Should it be static?
net/ipv6/ping.c:75:5: sparse: symbol 'dummy_ipv6_chk_addr' was not declared. Should it be static?
net/ipv6/ping.c:201:5: sparse: symbol 'ping_v6_seq_show' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All accesses of the tid_start_tx lock should be protected
by sta->lock if there is any chance that another thread
could still be accessing the sta object.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- fix "rtnl locked" concurrent executions by using rtnl_lock instead of
rtnl_trylock. This fix enables batman-adv initialisation to do not fail just
because somewhere else in the system another code path is holding the rtnl
lock. It is easy to see the problem when batman-adv is trying to start
together with other networking components.
- fix the routing protocol forwarding policy by enhancing the duplicate control
packet detection. When the right circumstances trigger the issue, some nodes in
the network become totally unreachable, so breaking the mesh connectivity.
- fix the Bridge Loop Avoidance component by not running the originator address
change handling routine when the component is disabled. The routine was
generating useless packets that were sent over the network.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=oGCV
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included change:
- fix "rtnl locked" concurrent executions by using rtnl_lock instead of
rtnl_trylock. This fix enables batman-adv initialisation to do not fail just
because somewhere else in the system another code path is holding the rtnl
lock. It is easy to see the problem when batman-adv is trying to start
together with other networking components.
- fix the routing protocol forwarding policy by enhancing the duplicate control
packet detection. When the right circumstances trigger the issue, some nodes in
the network become totally unreachable, so breaking the mesh connectivity.
- fix the Bridge Loop Avoidance component by not running the originator address
change handling routine when the component is disabled. The routine was
generating useless packets that were sent over the network.
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrects an byte order conflict introduced by
158874cac6
("sctp: Correct access to skb->{network, transport}_header").
The values in question are host byte order.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit da12c90e09
"netlink: Add compare function for netlink_table"
only set compare at the time we create kernel netlink,
and reset compare to NULL at the time we finially
release netlink socket, but netlink_lookup wants
the compare exist always.
So we should set compare after we allocate nl_table,
and never reset it. make comapre exist all the time.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking update from David Miller:
1) Fix dump iterator in nfnl_acct_dump() and ctnl_timeout_dump() to
dump all objects properly, from Pablo Neira Ayuso.
2) xt_TCPMSS must use the default MSS of 536 when no MSS TCP option is
present. Fix from Phil Oester.
3) qdisc_get_rtab() looks for an existing matching rate table and uses
that instead of creating a new one. However, it's key matching is
incomplete, it fails to check to make sure the ->data[] array is
identical too. Fix from Eric Dumazet.
4) ip_vs_dest_entry isn't fully initialized before copying back to
userspace, fix from Dan Carpenter.
5) Fix ubuf reference counting regression in vhost_net, from Jason
Wang.
6) When sock_diag dumps a socket filter back to userspace, we have to
translate it out of the kernel's internal representation first.
From Nicolas Dichtel.
7) davinci_mdio holds a spinlock while calling pm_runtime, which
sleeps. Fix from Sebastian Siewior.
8) Timeout check in sh_eth_check_reset is off by one, from Sergei
Shtylyov.
9) If sctp socket init fails, we can NULL deref during cleanup. Fix
from Daniel Borkmann.
10) netlink_mmap() does not propagate errors properly, from Patrick
McHardy.
11) Disable powersave and use minstrel by default in ath9k. From Sujith
Manoharan.
12) Fix a regression in that SOCK_ZEROCOPY is not set on tuntap sockets
which prevents vhost from being able to use zerocopy. From Jason
Wang.
13) Fix race between port lookup and TX path in team driver, from Jiri
Pirko.
14) Missing length checks in bluetooth L2CAP packet parsing, from Johan
Hedberg.
15) rtlwifi fails to connect to networking using any encryption method
other than WPA2. Fix from Larry Finger.
16) Fix iwlegacy build due to incorrect CONFIG_* ifdeffing for power
management stuff. From Yijing Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
b43: stop format string leaking into error msgs
ath9k: Use minstrel rate control by default
Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity"
ath9k: Disable PowerSave by default
net: wireless: iwlegacy: fix build error for il_pm_ops
rtlwifi: Fix a false leak indication for PCI devices
wl12xx/wl18xx: scan all 5ghz channels
wl12xx: increase minimum singlerole firmware version required
wl12xx: fix minimum required firmware version for wl127x multirole
rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks
mwifiex: debugfs: Fix out of bounds array access
Bluetooth: Fix mgmt handling of power on failures
Bluetooth: Fix missing length checks for L2CAP signalling PDUs
Bluetooth: btmrvl: support Marvell Bluetooth device SD8897
Bluetooth: Fix checks for LE support on LE-only controllers
team: fix checks in team_get_first_port_txable_rcu()
team: move add to port list before port enablement
team: check return value of team_get_port_by_index_rcu() for NULL
tuntap: set SOCK_ZEROCOPY flag during open
netlink: fix error propagation in netlink_mmap()
...
Ben reports that kmemleak is saying TX aggregation TID
structs are leaked. Given his workload, I suspect that
they're leaked because stations are destroyed before
their aggregation sessions get a chance to start. Fix
this by simply freeing structs that are not used yet.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit ba418fa357 ("soreuseport: UDP/IPv4 implementation")
added following sparse errors :
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:433:60: warning: incorrect type in argument 1 (different base types)
net/ipv4/udp.c:433:60: expected unsigned short [unsigned] [usertype] val
net/ipv4/udp.c:433:60: got restricted __be16 [usertype] sport
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:433:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: incorrect type in argument 1 (different base types)
net/ipv4/udp.c:514:60: expected unsigned short [unsigned] [usertype] val
net/ipv4/udp.c:514:60: got restricted __be16 [usertype] sport
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
net/ipv4/udp.c:514:60: warning: cast from restricted __be16
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse error :
net/ipv4/af_inet.c:1410:59: warning: restricted __be16 degrades to
integer
added in commit db8caf3dbc
("gro: should aggregate frames without DF")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This pull request is intended for the 3.11 stream...
One big highlight is the cw1200 driver the ST-E CW1100 & CW1200
WLAN chipsets. This one has been lingering for a while, lacking
some review comments. Once started getting pulled into linux-next,
it got a bit more attention and a number of improvements were made
over the initial cut. No doubt there will be more changes ahead,
but I think it is looking alright at this point.
Along with that, there is the usual flurry of updates to the mac80211
core and the iwlwifi, mwifiex, ath9k, rt2x00, wil6210, and other
drivers. A few of the highlights are some rt2x00 refactoring/cleanup
by Gabor Juhos, some rt2800 hardware support enhancements by Stanislaw
Gruszka, some iwlwifi power management updates from Alexander Bondar,
some enhanced bcma SPROM support from Rafał Miłecki, and a variety
of other things here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse errors :
net/ipv4/igmp.c:1222:25: warning: cast from restricted __be32
net/ipv4/igmp.c🔢31: warning: incorrect type in assignment (different address spaces)
net/ipv4/igmp.c🔢31: expected struct ip_mc_list [noderef] <asn:4>*next_hash
net/ipv4/igmp.c🔢31: got struct ip_mc_list *<noident>
net/ipv4/igmp.c:1250:31: warning: incorrect type in assignment (different address spaces)
net/ipv4/igmp.c:1250:31: expected struct ip_mc_list [noderef] <asn:4>*next_hash
net/ipv4/igmp.c:1250:31: got struct ip_mc_list *<noident>
net/ipv4/igmp.c:2380:37: warning: cast from restricted __be32
These were added by commit e989707135
("igmp: hash a hash table to speedup ip_check_mc_rcu()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ceph fixes from Sage Weil:
"There is a pair of fixes for double-frees in the recent bundle for
3.10, a couple of fixes for long-standing bugs (sleep while atomic and
an endianness fix), and a locking fix that can be triggered when osds
are going down"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix cleanup in rbd_add()
rbd: don't destroy ceph_opts in rbd_add()
ceph: ceph_pagelist_append might sleep while atomic
ceph: add cpu_to_le32() calls when encoding a reconnect capability
libceph: must hold mutex for reset_changed_osds()
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LE-only controllers do not support extended features so any kind of host
feature bit checks do not make sense for them. This patch fixes code
used for both single-mode (LE-only) and dual-mode (BR/EDR/LE) to use the
HCI_LE_ENABLED flag instead of the "Host LE supported" feature bit for
LE support tests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to commit bc6bcb59 ("netfilter: xt_TCPOPTSTRIP: fix
possible mangling beyond packet boundary"), add safe fragment
handling to xt_TCPMSS.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As a followup to commit 409b545a ("netfilter: xt_TCPMSS: Fix violation
of RFC879 in absence of MSS option"), John Heffner points out that IPv6
has a higher MTU than IPv4, and thus a higher minimum MSS. Update TCPMSS
target to account for this, and update RFC comment.
While at it, point to more recent reference RFC1122 instead of RFC879.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We currently allow for numa-node aware skb allocation only within the
fill_packet_ipv4() path, but not in fill_packet_ipv6(). Consolidate that
code to a common allocation helper to enable numa-node aware skb
allocation for ipv6, and use it in both paths. This also makes both
functions a bit more readable.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to TCP offloading and UDPv6 offloading, move all related
UDPv4 functions to udp_offload.c to make things more explicit. Also,
by this, we can make those functions static.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_mc_init_dev() is passed a freshly kzalloc'd in_device so it is
unnecessary to explicitly zero out the members.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After IP route cache removal, multicast applications using
a lot of multicast addresses hit a O(N) behavior in ip_check_mc_rcu()
Add a per in_device hash table to get faster lookup.
This hash table is created only if the number of items in mc_list is
above 4.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a thousand htb classes, est_timer() spends ~5 million cpu cycles
and throws out cpu cache, because each htb class has a default
rate estimator (est 4sec 16sec).
Most users do not use default rate estimators, so switch htb
to not setup ones.
Add a module parameter (htb_rate_est) so that users relying
on this default rate estimator can revert the behavior.
echo 1 >/sys/module/sch_htb/parameters/htb_rate_est
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of parameters was mixed up, introduced in commit
"mac80211: improve the rate control API"
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a CAC is running and stop_ap is called (e.g. when hostapd is killed
while performing CAC), the CAC must be aborted immediately.
Otherwise ieee80211_stop_ap() will try to stop it when it's too late -
wdev->channel is already NULL and the abort event can not be generated.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some APs, notably 2G/3G/4G Wifi routers, specifically the
"Onda PN51T", "Vodafone PocketWiFi 2", "ZTE MF60" and a similar
T-Mobile branded device [1] that erroneously don't include all the
needed information in (re)association response frames. Work around
this by assuming the information is the same as it was in the
beacon or probe response and using the data from there instead.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58881.
[1] https://bbs.archlinux.org/viewtopic.php?pid=1277305
Note that this requires marking the first ieee802_11_parse_elems()
argument const, otherwise we'd get a compiler warning.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Michal Zajac <manwe@manwe.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before allowing 64bits bytes rates, refactor
psched_ratecfg_precompute() to get better comments
and increased accuracy.
rate_bps field is renamed to rate_bytes_ps, as we only
have to worry about bytes per second.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In two wiphy dump error cases, most often when the dump allocation
must be increased, the RTNL is leaked. This quickly results in a
complete system lockup. Release the RTNL correctly.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may want to send a frame on the current channel
without specifying it.
This is particularly useful for the correct implementation
of the IBSS/RSN support in wpa_supplicant which requires to
receive and send AUTH frames.
Make mgmt_tx pass a NULL channel to the driver if none has
been specified by the user.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 passes a NULL channel to mgmt_tx if the frame has
to be sent on the one currently in use by the device.
Make the implementation of mgmt_tx correctly handle this
case. Fail if offchan is required.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[fix RCU locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I (Johannes) accidentally applied the first version of the patch
("Allow TDLS peer AID to be configured for VHT"). Now apply just
the changes between v1 and v2 to get the AID verification and
prefer the new attribute over the old one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time it takes to see the peer link expire may differ
by a minute since sta_expire() is run once a minute as a
mesh housekeeping task.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch "cfg80211/mac80211: use cfg80211 wdev mutex in
mac80211" introduced several deadlocks by converting the
ifmsh->mtx to wdev->mtx. Solve these by:
1. drop the cancel_work_sync() in ieee80211_stop_mesh().
Instead make the mesh work conditional on whether the mesh
is running or not.
2. lock the mesh work with sdata_lock() to protect beacon
updates and prevent races with wdev->mesh_id_len or
cfg80211.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return the error if something went wrong instead of unconditionally
returning 0.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct gnet_stats_rate_est contains u32 fields, so the bytes per second
field can wrap at 34360Mbit.
Add a new gnet_stats_rate_est64 structure to get 64bit bps/pps fields,
and switch the kernel to use this structure natively.
This structure is dumped to user space as a new attribute :
TCA_STATS_RATE_EST64
Old tc command will now display the capped bps (to 34360Mbit), instead
of wrapped values, and updated tc command will display correct
information.
Old tc command output, after patch :
eric:~# tc -s -d qd sh dev lo
qdisc pfifo 8001: root refcnt 2 limit 1000p
Sent 80868245400 bytes 1978837 pkt (dropped 0, overlimits 0 requeues 0)
rate 34360Mbit 189696pps backlog 0b 0p requeues 0
This patch carefully reorganizes "struct Qdisc" layout to get optimal
performance on SMP.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While stress testing sctp sockets, I hit the following panic:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffffa0490c4e>] sctp_endpoint_free+0xe/0x40 [sctp]
PGD 7cead067 PUD 7ce76067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in: sctp(F) libcrc32c(F) [...]
CPU: 7 PID: 2950 Comm: acc Tainted: GF 3.10.0-rc2+ #1
Hardware name: Dell Inc. PowerEdge T410/0H19HD, BIOS 1.6.3 02/01/2011
task: ffff88007ce0e0c0 ti: ffff88007b568000 task.ti: ffff88007b568000
RIP: 0010:[<ffffffffa0490c4e>] [<ffffffffa0490c4e>] sctp_endpoint_free+0xe/0x40 [sctp]
RSP: 0018:ffff88007b569e08 EFLAGS: 00010292
RAX: 0000000000000000 RBX: ffff88007db78a00 RCX: dead000000200200
RDX: ffffffffa049fdb0 RSI: ffff8800379baf38 RDI: 0000000000000000
RBP: ffff88007b569e18 R08: ffff88007c230da0 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff880077990d00 R14: 0000000000000084 R15: ffff88007db78a00
FS: 00007fc18ab61700(0000) GS:ffff88007fc60000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000020 CR3: 000000007cf9d000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007b569e38 ffff88007db78a00 ffff88007b569e38 ffffffffa049fded
ffffffff81abf0c0 ffff88007db78a00 ffff88007b569e58 ffffffff8145b60e
0000000000000000 0000000000000000 ffff88007b569eb8 ffffffff814df36e
Call Trace:
[<ffffffffa049fded>] sctp_destroy_sock+0x3d/0x80 [sctp]
[<ffffffff8145b60e>] sk_common_release+0x1e/0xf0
[<ffffffff814df36e>] inet_create+0x2ae/0x350
[<ffffffff81455a6f>] __sock_create+0x11f/0x240
[<ffffffff81455bf0>] sock_create+0x30/0x40
[<ffffffff8145696c>] SyS_socket+0x4c/0xc0
[<ffffffff815403be>] ? do_page_fault+0xe/0x10
[<ffffffff8153cb32>] ? page_fault+0x22/0x30
[<ffffffff81544e02>] system_call_fastpath+0x16/0x1b
Code: 0c c9 c3 66 2e 0f 1f 84 00 00 00 00 00 e8 fb fe ff ff c9 c3 66 0f
1f 84 00 00 00 00 00 55 48 89 e5 53 48 83 ec 08 66 66 66 66 90 <48>
8b 47 20 48 89 fb c6 47 1c 01 c6 40 12 07 e8 9e 68 01 00 48
RIP [<ffffffffa0490c4e>] sctp_endpoint_free+0xe/0x40 [sctp]
RSP <ffff88007b569e08>
CR2: 0000000000000020
---[ end trace e0d71ec1108c1dd9 ]---
I did not hit this with the lksctp-tools functional tests, but with a
small, multi-threaded test program, that heavily allocates, binds,
listens and waits in accept on sctp sockets, and then randomly kills
some of them (no need for an actual client in this case to hit this).
Then, again, allocating, binding, etc, and then killing child processes.
This panic then only occurs when ``echo 1 > /proc/sys/net/sctp/auth_enable''
is set. The cause for that is actually very simple: in sctp_endpoint_init()
we enter the path of sctp_auth_init_hmacs(). There, we try to allocate
our crypto transforms through crypto_alloc_hash(). In our scenario,
it then can happen that crypto_alloc_hash() fails with -EINTR from
crypto_larval_wait(), thus we bail out and release the socket via
sk_common_release(), sctp_destroy_sock() and hit the NULL pointer
dereference as soon as we try to access members in the endpoint during
sctp_endpoint_free(), since endpoint at that time is still NULL. Now,
if we have that case, we do not need to do any cleanup work and just
leave the destruction handler.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1a37e412a022(net: Use 16bits for *_headers fields of struct
skbuff), skb->*_header are relative to skb->head,
so copy_skb_header() should not call skb_headers_offset_update() now,
and we should pass correct parameter to skb_headers_offset_update() in
pskb_expand_head() and skb_copy_expand().
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we know, netlink sockets are private resource of
net namespace, they can communicate with each other
only when they in the same net namespace. this works
well until we try to add namespace support for other
subsystems which use netlink.
Don't like ipv4 and route table.., it is not suited to
make these subsytems belong to net namespace, Such as
audit and crypto subsystems,they are more suitable to
user namespace.
So we must have the ability to make the netlink sockets
in same user namespace can communicate with each other.
This patch adds a new function pointer "compare" for
netlink_table, we can decide if the netlink sockets can
communicate with each other through this netlink_table
self-defined compare function.
The behavior isn't changed if we don't provide the compare
function for netlink_table.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Serge E. Hallyn <serge.hallyn@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to control flood of unicast traffic. By default, flood is
on and the bridge will flood unicast traffic if it doesn't know
the destination. When the flag is turned off, unicast traffic
without an FDB will not be forwarded to the specified port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to control whether mac learning is enabled on the port.
By default, mac learning is enabled. Disabling mac learning will
cause new dynamic FDB entries to not be created for a particular port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filters need to be translated to real BPF code for userland, like SO_GETFILTER.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the following commits:
commit 00f97da17a (netpoll: fix position of network header)
commit 525cebedb3 (pktgen: Fix position of ip and udp header)
using skb_tail_offset() seems not correct since the offset
is based on head pointer.
With the last caller removed, skb_tail_offset() can be killed
finally.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Daniel Borkmann <dborkmann@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds low latency socket poll support for TCP.
In tcp_v[46]_rcv() add a call to sk_mark_ll() to copy the napi_id
from the skb to the sk.
In tcp_recvmsg(), when there is no data in the socket we busy-poll.
This is a good example of how to add busy-poll support to more protocols.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add upport for busy-polling on UDP sockets.
In __udp[46]_lib_rcv add a call to sk_mark_ll() to copy the napi_id
from the skb into the sk.
This is done at the earliest possible moment, right after we identify
which socket this skb is for.
In __skb_recv_datagram When there is no data and the user
tries to read we busy poll.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a napi_id and a hashing mechanism to lookup a napi by id.
This will be used by subsequent patches to implement low latency
Ethernet device polling.
Based on a code sample by Eric Dumazet.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In (bc6bcb5 netfilter: xt_TCPOPTSTRIP: fix possible mangling beyond
packet boundary), the use of tcp_hdr was introduced. However, we
cannot assume that skb->transport_header is set for non-local packets.
Cc: Florian Westphal <fw@strlen.de>
Reported-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
The following patchset contains four fixes for Netfilter and one fix
for IPVS, they are:
* Fix data leak to user-space via getsockopt IP_VS_SO_GET_DESTS, from
Dan Carpenter.
* Fix xt_TCPMSS if no TCP MSS is specified in syn packets, to avoid the
violation of RFC879, from Phil Oester.
* Fix incomplete dump of objects via nfnetlink_acct and nfnetlink_cttimeout,
from myself.
* Fix missing HW protocol in packets passed to user-space via NFQUEUE,
from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry struct has a 2 byte hole after ->port and another 4 byte
hole after ->stats.outpkts. You must have CAP_NET_ADMIN in your
namespace to hit this information leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The bridge loop avoidance has a hook to handle address updates of the
originator. These should not be handled when bridge loop avoidance is
disabled - it might send some bridge loop avoidance packets which should
not appear if bla is disabled.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When a packet is received from another node first and later from the
best next hop, this packet is dropped. However the first OGM was sent
with the BATADV_NOT_BEST_NEXT_HOP flag and thus dropped by neighbors.
The late OGM from the best neighbor is then dropped because it is a
duplicate.
If this situation happens constantly, a node might end up not forwarding
the "valid" OGMs anymore, and nodes behind will starve from not getting
valid OGMs.
Fix this by refining the duplicate checking behaviour: The actions
should depend on whether it was a duplicate for a neighbor only or for
the originator. OGMs which are not duplicates for a specific neighbor
will now be considered in batadv_iv_ogm_forward(), but only actually
forwarded for the best next hop. Therefore, late OGMs from the best
next hop are forwarded now and not dropped as duplicates anymore.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The rtnl_lock in batadv_store_mesh_iface has been converted to a rtnl_trylock
some time ago to avoid a possible deadlock between rtnl and s_active on removal
of the sysfs nodes.
The behaviour introduced by that was quite confusing as it could lead to the
sysfs store to fail, making batman-adv setup scripts unreliable. As recently the
sysfs removal was postponed to a worker not running with the rtnl taken, the
deadlock can't occur any more and it is safe to change the trylock back to a
lock to make the sysfs store reliable again.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Reviewed-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
I can hit ENOBUFS in the sendmsg() path with a large batch that is
composed of many netlink messages. Here that limit is 8 MBytes of
skbuff data area as kmalloc does not manage to get more than that.
While discussing atomic rule-set for nftables with Patrick McHardy,
we decided to put all rule-set updates that need to be applied
atomically in one single batch to simplify the existing approach.
However, as explained above, the existing netlink code limits us
to a maximum of ~20000 rules that fit in one single batch without
hitting ENOBUFS. iptables does not have such limitation as it is
using vmalloc.
This patch adds netlink_alloc_large_skb() which is only used in
the netlink_sendmsg() path. It uses alloc_skb if the memory
requested is <= one memory page, that should be the common case
for most subsystems, else vmalloc for higher memory allocations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_get_rtab() should check not only the keys in struct tc_ratespec,
but also the full data[] array.
"tc ... linklayer atm " only perturbs values in the 256 slots array.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Would be good to make things explicit and move those functions to
a new file called tcp_offload.c, thus make this similar to tcpv6_offload.c.
While moving all related functions into tcp_offload.c, we can also
make some of them static, since they are only used there. Also, add
an explicit registration function.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have the minimal inline helper tcp_skb_mss to access
skb_shinfo(skb)->gso_size, so also use it here to get mss.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RPC_TASK_RUNNING flag will always have been set in rpc_make_runnable()
once we get past the test for out_of_line_wait_on_bit() returning
ERESTARTSYS.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the rpc_task is asynchronous, it could theoretically finish executing
on the workqueue it was assigned by rpc_make_runnable() before we get
round to testing RPC_IS_ASYNC() in rpc_execute.
In practice, however, all the existing callers hold a reference to the
rpc_task, so this can't happen today...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I broke them in this commit:
commit 1be374a051
Author: Andy Lutomirski <luto@amacapital.net>
Date: Wed May 22 14:07:44 2013 -0700
net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg
This patch adds __sys_sendmsg and __sys_sendmsg as common helpers that accept
MSG_CMSG_COMPAT and blocks MSG_CMSG_COMPAT at the syscall entrypoints. It
also reverts some unnecessary checks in sys_socketcall.
Apparently I was suffering from underscore blindness the first time around.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/netfilter/nf_log.c
The conflict in nf_log.c is that in 'net' we added CONFIG_PROC_FS
protection around foo_proc_entry() calls to fix a build failure,
whereas in Pablo's tree a guard if() test around a call is
remove_proc_entry() was removed. Trivially resolved.
Pablo Neira Ayuso says:
====================
The following patchset contains the first batch of
Netfilter/IPVS updates for your net-next tree, they are:
* Three patches with improvements and code refactorization
for nfnetlink_queue, from Florian Westphal.
* FTP helper now parses replies without brackets, as RFC1123
recommends, from Jeff Mahoney.
* Rise a warning to tell everyone about ULOG deprecation,
NFLOG has been already in the kernel tree for long time
and supersedes the old logging over netlink stub, from
myself.
* Don't panic if we fail to load netfilter core framework,
just bail out instead, from myself.
* Add cond_resched_rcu, used by IPVS to allow rescheduling
while walking over big hashtables, from Simon Horman.
* Change type of IPVS sysctl_sync_qlen_max sysctl to avoid
possible overflow, from Zhang Yanfei.
* Use strlcpy instead of strncpy to skip zeroing of already
initialized area to write the extension names in ebtables,
from Chen Gang.
* Use already existing per-cpu notrack object from xt_CT,
from Eric Dumazet.
* Save explicit socket lookup in xt_socket now that we have
early demux, also from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When host ping its peer, ICMP echo request packet triggers IPsec
policy, then host negotiates SA secret with its peer. After IKE
installed SA for OUT direction, but before SA for IN direction
installed, host get ICMP echo reply from its peer. At the time
being, the SA state for IN direction could be XFRM_STATE_ACQ,
then the received packet will be dropped after adding
LINUX_MIB_XFRMINSTATEINVALID statistic.
Adding a LINUX_MIB_XFRMACQUIREERROR statistic counter for such
scenario when SA in larval state is much clearer for user than
LINUX_MIB_XFRMINSTATEINVALID which indicates the SA is totally
bad.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have at least one user of this function outside of CONFIG_NET
scope, we have to provide this function independently. The proposed
solution is to move it under lib/net_utils.c with corresponding
configuration variable and select wherever it is needed.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clamp-mss-to-pmtu option of the xt_TCPMSS target can cause issues
connecting to websites if there was no MSS option present in the
original SYN packet from the client. In these cases, it may add a
MSS higher than the default specified in RFC879. Fix this by never
setting a value > 536 if no MSS option was specified by the client.
This closes netfilter's bugzilla #662.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CAP_LEN contains the size of the network packet we're queueing to
userspace, i.e. normally it is the same as the NFQA_PAYLOAD attribute len.
Include it only in the unlikely case when NFQA_PAYLOAD is truncated due
to copy_range limitations.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For every packet queued, we check if configured copy_range
is 0, and treat that as 'copy entire packet'.
We can move this check to the queue configuration, and can
set copy_range appropriately.
Also, convert repetitive '0xffff - NLA_HDRLEN' to a macro.
[ queue initialization still used 0xffff, although its harmless
since the initial setting is overwritten on queue config ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix broken incomplete object dumping if the list of objects does not
fit into one single netlink message.
Reported-by: Gabriel Lazar <Gabriel.Lazar@com.utcluj.ro>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix broken incomplete object dumping if the list of objects does not
fit into one single netlink message.
Reported-by: Gabriel Lazar <Gabriel.Lazar@com.utcluj.ro>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Fix timeouts with direct mode authentication in mac80211, from
Stanislaw Gruszka.
2) Aggregation sessions can deadlock in ath9k, from Felix Fietkau.
3) Netfilter's xt_addrtype doesn't work with ipv6 due to route lookups
creating undesirable cache entries, from Florian Westphal.
4) Fix netfilter's ipt_ULOG from generating non-NULL terminated
strings.
5) Fix netdev transmit queue crashes in mac80211, from Johannes Berg.
6) Fix copy and paste error in 802.11 stack that broke reporting of
64-bit station tx statistics, from Felix Fietkau.
7) When qlge_probe fails, it leaks the netdev. Fix from Wei Yongjun.
8) SKB control block (where we store the IP options information,
amongst other things) must be cleared properly otherwise ICMP
sending can crash for IP tunnels. Fix from Eric Dumazet.
9) Verification of Energy Efficient Ether support was coded wrongly,
the test was inversed. Fix from Giuseppe CAVALLARO.
10) TCP handles redirects improperly because the wrong flow key is used
for the route lookup. From Michal Kubecek.
11) Don't interpret MSG_CMSG_COMPAT from userspace, fix from Andy
Lutomirski.
12) The new AF_VSOCK was missing from the lockdep string table, fix from
Federico Vaga.
13) be2net doesn't handle checksumming of IP fragments properly, from
Somnath Kotur.
14) Fix several bugs in the device address list code that lead to
crashes and other misbehaviors. From Jay Vosburgh.
15) Fix ipv6 segmentation handling of fragmented GRE tunnel traffic,
from Pravin B Shalr.
16) Fix usage of stale policies in IPSEC layer, from Paul Moore.
17) Fix team driver dump of ports when there are a large number of them,
from Jiri Pirko.
18) Fix softlockups in UDP ipv4 socket lookup causes by and error in the
hlist_nulls_for_each_entry_rcu() macro. From Eric Dumazet.
19) Fix several regressions added by the high rate accuracy changes to
the htb packet scheduler. From Eric Dumazet.
20) Fix DMA'ing onto the stack in esd_usb2 and peak_usb CAN drivers,
from Olivier Sobrie and Marc Kleine-Budde.
21) Fix unremovable network devices due to missing route pointer
installation in the per-device ipv6 address list entries. From Gao
feng.
22) Apply the tg3 5719 DMA workaround on 5720 chips as well, otherwise
we get stalls. From Nithin Sujir.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
net_sched: htb: do not mix 1ns and 64ns time units
net: fix sk_buff head without data area
tg3: Add read dma workaround for 5720
net: ethernet: xilinx_emaclite: set protocol selector bits when writing ANAR
bnx2x: Fix bridged GSO for 57710/57711 chips
net: fec: add fallback to random MAC address
bnx2x: fix TCP offload for tunneling ipv4 over ipv6
ipv6: assign rt6_info to inet6_ifaddr in init_loopback
net/mlx4_core: Keep VF assigned MAC in the PF admin table
net/mlx4_en: Handle unassigned VF MAC address correctly
net/mlx4_core: Return -EPROBE_DEFER when a VF is probed before PF is sufficiently initialized
net/mlx4_en: Fix adaptive moderation cq update
net: can: peak_usb: Do not do dma on the stack
net: can: esd_usb2: Do not do dma on the stack
net: can: kvaser_usb: fix reception on "USBcan Pro" and "USBcan R" type hardware.
net_sched: restore "overhead xxx" handling
net: force a reload of first item in hlist_nulls_for_each_entry_rcu
hyperv: Fix vlan_proto setting in netvsc_recv_callback()
team: fix port list dump for big number of ports
list: introduce list_first_entry_or_null
...
Currently beacon availability upon association is marked by have_beacon
flag of assoc_data structure that becomes unavailable when association
completes. However beacon availability indication is required also after
association to inform a driver. Currently dtim_period parameter is used
for this purpose. Move have_beacon flag to another structure, persistant
throughout a interface's life cycle. Use suitable sematics for beacon
availability indication.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[fix another instance of BSS_CHANGED_DTIM_PERIOD in docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_rx_bss_info() deals with dtim_period setting and PS update
when associated. Move all these to another locations cleaning this
function. Also, the current implementation is buggy because when it
calls ieee80211_recalc_ps() bss_conf->dtim_period is notset properly
yet and thus nothing will happen.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 56b765b79 ("htb: improved accuracy at high rates") added another
regression for low rates, because it mixes 1ns and 64ns time units.
So the maximum delay (mbuffer) was not 60 second, but 937 ms.
Lets convert all time fields to 1ns as 64bit arches are becoming the
norm.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the problem in pktgen, netpoll uses skb_tail_offset()
too, as the code is copied from pktgen.
Also use return values of skb_put() directly, this will simiplify
the code.
Reported-by: Thomas Graf <tgraf@suug.ch>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Daniel Borkmann <dborkmann@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_set_network_header() expects an offset based on the data pointer
whereas skb_tail_offset() also includes the headroom. This resulted
in the ip header being written in a wrong location.
Use return values of skb_put() directly and rely on skb->len to
set mac, network, and transport header.
Cc: Simon Horman <horms@verge.net.au>
Cc: Daniel Borkmann <dborkmann@redhat.com>
Assisted-by: Daniel Borkmann <dborkmann@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <dborkmann@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet spotted that we have to check skb->head instead
of skb->data as skb->head points to the beginning of the
data area of the skbuff. Similarly, we have to initialize the
skb->head pointer, not skb->data in __alloc_skb_head.
After this fix, netlink crashes in the release path of the
sk_buff, so let's fix that as well.
This bug was introduced in (0ebd0ac net: add function to
allocate sk_buff head without data area).
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't need scope id, we should initialize it to zero.
Same for ->sin6_flowinfo.
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 25fb6ca4ed
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
forgot to assign rt6_info to the inet6_ifaddr.
When disable the net device, the rt6_info which allocated
in init_loopback will not be destroied in __ipv6_ifa_notify.
This will trigger the waring message below
[23527.916091] unregister_netdevice: waiting for tap0 to become free. Usage count = 1
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_create_hash() is only called from netdev_init() which is marked
__net_init.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 202dc3fc59 (Documentation: remove
obsolete networking/multicast.txt file) deleted the obsolete file. After
the file has been removed, clean up a couple of places where references
to the deleted file were made so that users wouldn't be confused when
they consult the Help menu.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up unnecessary assignment and jump. While there, fix up the label
name.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to use atomic_inc_return() for assigning the wiphy
index made the first wiphy index 1 instead of 0. This is fine,
but we all habitually type "phy0" when we're testing, so make
it go back to 0 instead of 1 by subtracting 1 from the index.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My big locking cleanups caused a problem by registering the
rfkill instance with the RTNL held, while the callback also
acquires the RTNL. This potentially causes a deadlock since
the two locks used (rfkill mutex and RTNL) can be acquired
in two different orders. Fix this by (un)registering rfkill
without holding the RTNL. This needs to be done after the
device struct is registered, but that can also be done w/o
holding the RTNL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The format is based on /proc/net/icmp and /proc/net/{udp,raw}6.
Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Couldn't figure out how to test without CONFIG_PROC_FS enabled.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a ping_seq_afinfo structure (similar to its UDP
equivalent) and use it to make some of the ping /proc functions
address-family independent. Rename the remaining ping /proc
functions from ping_* to ping_v4_*.
Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp6_sock_seq_show and raw6_sock_seq_show are identical, except
the UDP version displays ports and the raw version displays the
protocol. Refactor most of the code in these two functions into
a new common ip6_dgram_sock_seq_show function, in preparation
for using it to display ICMPv6 sockets as well.
Also reduce the indentation in parts of include/net/transp_v6.h
to improve readability.
Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
get_reg_request_treatment() returns 0 in one case but is
defined to return an enum, use the proper value REG_REQ_OK.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The connection monitor needs to know the tx status of
nullframes to work properly.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_end() can't return an error since it returns the
skb length so remove checks treating the return value as
an error code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cap max peerings at 63 in accordance with IEEE-2012 8.4.2.100.7.
Triggers a beacon regeneration every time the number of peerings changes.
Previously this would only happen if the "accepting peerings" bit changed.
Signed-off-by: Jacob Minshall <jacob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211 has already verified the mesh TTL on setting the
mesh config, so no need to check it again in mac80211.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My cfg80211/mac80211 locking unification broke the sdata
locking in ieee80211_set_power_mgmt, it needs to acquire
the lock for __ieee80211_request_smps(). Add the locking.
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
struct icmp_bxm is a large struct, reduce stack usage
by allocating it on heap.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP_PARAMETERPROB is handled by icmp_unreach(); This patch adds
ICMP_PARAMETERPROB to the list of ICMP message types handled by icmp_unreach().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 13d82bf5 (ipv4: Fix flushing of cached routing informations)
added the support to flush learned pmtu information.
However, using rt_genid is quite heavy as it is bumped on route
add/change and multicast events amongst other places. These can
happen quite often, especially if using dynamic routing protocols.
While this is ok with routes (as they are just recreated locally),
the pmtu information is learned from remote systems and the icmp
notification can come with long delays. It is worthy to have separate
genid to avoid excessive pmtu resets.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tunnel devices call update_pmtu for each packet sent, this causes
contention on the fnhe_lock. Ignore the pmtu update if pmtu is not
actually changed, and there is still plenty of time before the entry
expires.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 05ab86c5 (xfrm4: Invalidate all ipv4 routes on
IPsec pmtu events). Flushing all cached entries is not needed.
Instead, invalidate only the related next hop dsts to recheck for
the added next hop exception where needed. This also fixes a subtle
race due to bumping generation id's before updating the pmtu.
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 56b765b79 ("htb: improved accuracy at high rates")
broke the "overhead xxx" handling, as well as the "linklayer atm"
attribute.
tc class add ... htb rate X ceil Y linklayer atm overhead 10
This patch restores the "overhead xxx" handling, for htb, tbf
and act_police
The "linklayer atm" thing needs a separate fix.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Vimalkumar <j.vimal@gmail.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases after deleting a policy from the SPD the policy would
remain in the dst/flow/route cache for an extended period of time
which caused problems for SELinux as its dynamic network access
controls key off of the number of XFRM policy and state entries.
This patch corrects this problem by forcing a XFRM garbage collection
whenever a policy is sucessfully removed.
Reported-by: Ondrej Moris <omoris@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of IPv4 over Ipv4 for the module sit. The gain of
this feature is to be able to have 4in4 and 6in4 over the same interface
instead of having one interface for 6in4 and another for 4in4 even if
encapsulation addresses are the same.
To avoid conflicting with ipip module, sit IPv4 over IPv4 protocol is
registered with a smaller priority.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, ip_tunnel_xmit() was using the field protocol from the IP
header passed into argument.
There is no functional change, this patch prepares the support of IPv4 over
IPv4 for module sit.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp6 over GRE tunnel does not work after to GRE tso changes. GRE
tso handler passes inner packet but keeps track of outer header
start in SKB_GSO_CB(skb)->mac_offset. udp6 fragment need to
take care of outer header, which start at the mac_offset, while
adding fragment header.
This bug is introduced by commit 68c3316311 (GRE: Add TCP
segmentation offload for GRE).
Reported-by: Dmitry Kravkov <dkravkov@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Tested-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1a37e412a0 (net: Use 16bits for *_headers
fields of struct skbuff) converts skb->*_header to u16,
some #if NET_SKBUFF_DATA_USES_OFFSET are now useless,
and to be safe, we could just use "X = (typeof(X)) ~0U;"
as suggested by David.
Cc: David S. Miller <davem@davemloft.net>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_mc_sync_multiple function is currently calling
__hw_addr_sync, and not __hw_addr_sync_multiple. This will result in
addresses only being synced to the first device from the set.
Corrected by calling the _multiple variant.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, __hw_addr_sync_one is called in a loop by
__hw_addr_sync_multiple to sync each of a "from" device's hw addresses
to a "to" device. __hw_addr_sync_one calls __hw_addr_add_ex to attempt
to add each address. __hw_addr_add_ex is called with global=false, and
sync=true.
__hw_addr_add_ex checks to see if the new address matches an
address already on the list. If so, it tests global and sync. In this
case, sync=true, and it then checks if the address is already synced,
and if so, returns 0.
This 0 return causes __hw_addr_sync_one to increment the sync_cnt
and refcount for the "from" list's address entry, even though the address
is already synced and has a reference and sync_cnt. This will cause
the sync_cnt and refcount to increment without bound every time an
addresses is added to the "from" device and synced to the "to" device.
The fix here has two parts:
First, when __hw_addr_add_ex finds the address already exists
and is synced, return -EEXIST instead of 0.
Second, __hw_addr_sync_one checks the error return for -EEXIST,
and if so, it (a) does not add a refcount/sync_cnt, and (b) returns 0
itself so that __hw_addr_sync_multiple will not return an error.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an address is added to a subordinate interface (the "to"
list), the address entry in the "from" list is not marked "synced" as
the entry added to the "to" list is.
When performing the unsync operation (e.g., dev_mc_unsync),
__hw_addr_unsync_one calls __hw_addr_del_entry with the "synced"
parameter set to true for the case when the address reference is being
released from the "from" list. This causes a test inside to fail,
with the result being that the reference count on the "from" address
is not properly decremeted and the address on the "from" list will
never be freed.
Correct this by having __hw_addr_unsync_one call the
__hw_addr_del_entry function with the "sync" flag set to false for the
"remove from the from list" case.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sync_cnt field is not being initialized, which can result
in arbitrary values in the field. Fixed by initializing it to zero.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->network_header
will be an offset from head. This is corrected by using wrappers that
ensure that calculations are always made using pointers.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This stat is not relevant in IPv6, there is no checksum in IPv6 header.
Just leave a comment to explain the hole.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO on IPv4 doesn't aggregate frames if they don't have DF bit set.
Some servers use IP_MTU_DISCOVER/IP_PMTUDISC_PROBE, so linux receivers
are unable to aggregate this kind of traffic.
The right thing to do is to allow aggregation as long as the DF bit has
same value on all segments.
bnx2x LRO does this correctly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current state of affairs is that read()/write() will setup
RFS (Receive Flow Steering) for internet protocol sockets while
poll()/epoll() does not.
When poll() gets called with a TCP or UDP socket, we should update
the flow target.
This permits to RFS (if enabled) to select the appropriate CPU for
following incoming packets.
Note: Only connected UDP sockets can benefit from RFS.
Signed-off-by: David Majnemer <majnemer@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Turner <pjt@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.10 stream...
Regarding the NFC bits, Samuel says:
"This is the first batch of NFC fixes for 3.10, and it contains:
- 3 fixes for the NFC MEI support:
* We now depend on the correct Kconfig symbol.
* We register an MEI event callback whenever we enable an NFC device,
otherwise we fail to read anything after an enable/disable cycle.
* We only disable an MEI device from its disable mey_phy_ops,
preventing useless consecutive disable calls.
- An NFC Makefile cleanup, as I forgot to remove a commented out line when
moving the LLCP code to the NFC top level directory."
As for the mac80211 bits, Johannes says:
"This time I have a fix from Stanislaw for a stupid mistake I made in the
auth/assoc timeout changes, a fix from Felix for 64-bit traffic counters
and one from Helmut for address mask handling in mac80211. I also have a
few fixes myself for four different crashes reported by a few people."
And Johannes says this about the iwlwifi bit:
"This fixes a brown paper-bag bug that we really should've caught in
review. More details in the changelog for the fix."
On top of that...
Arend van Spriel and Hante Meuleman cooperate to send a series of AP
and P2P mode fixes for brcmfmac.
Gabor Juhos corrects a register offset for AR9550, avoiding a bus
error.
Dan Carpenter provides a fixup to some dmesg output in the atmel
driver.
And, finally...
Felix Fietkau not only gives us a trio of small AR934x fixes, but
also refactors the ath9k aggregation session start/stop handling
(using the generic mac80211 support) in order to avoid a deadlock.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrects an byte order conflict introduced by "sctp: Correct access to
skb->{network, transport}_header". All the values in question are host
byte order.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the receiver supports DSACK, sender can detect false recoveries and
revert cwnd reductions triggered by either severe network reordering or
concurrent reordering and loss event.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon detecting spurious fast retransmit via timestamps during recovery,
use PRR to clock out new data packet instead of retransmission. Once
all retransmission are proven spurious, the sender then reverts the
cwnd reduction and congestion state to open or disorder.
The current code does the opposite: it undoes cwnd as soon as any
retransmission is spurious and continues to retransmit until all
data are acked. This nullifies the point to undo the cwnd because
the sender is still retransmistting spuriously. This patch fixes
it. The undo_ssthresh argument of tcp_undo_cwnd_reductiuon() is no
longer needed and is removed.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and relocate various functions or variables to prepare the
undo fix. Remove some unused function arguments. Rename tcp_undo_cwr
to tcp_undo_cwnd_reduction to be consistent with the rest of
CWR related function names.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series fixes an undo bug in fast recovery: the sender
mistakenly undos the cwnd too early but continues fast retransmits
until all pending data are acked. This also multiplies the SNMP
stat PARTIALUNDO events by the degree of the network reordering.
The first patch prepares the fix by consolidating the accounting
of newly_acked_sacked in tcp_cwnd_reduction(), instead of updating
newly_acked_sacked everytime sacked_out is adjusted. Also pass
acked and prior_unsacked as const type because they are readonly
in the rest of recovery processing.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd fixes from Bruce Fields:
"A couple minor fixes for the (new to 3.10) gss-proxy code.
And one regression from user-namespace changes. (XBMC clients were
doing something admittedly weird--sending -1 gid's--but something that
we used to allow.)"
* 'for-3.10' of git://linux-nfs.org/~bfields/linux:
svcrpc: fix failures to handle -1 uid's and gid's
svcrpc: implement O_NONBLOCK behavior for use-gss-proxy
svcauth_gss: fix error code in use_gss_proxy()
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter/IPVS fixes for 3.10-rc3,
they are:
* fix xt_addrtype with IPv6, from Florian Westphal. This required
a new hook for IPv6 functions in the netfilter core to avoid
hard dependencies with the ipv6 subsystem when this match is
only used for IPv4.
* fix connection reuse case in IPVS. Currently, if an reused
connection are directed to the same server. If that server is
down, those connection would fail. Therefore, clear the
connection and choose a new server among the available ones.
* fix possible non-nul terminated string sent to user-space if
ipt_ULOG is used as the default netfilter logging stub, from
Chen Gang.
* fix mark logging of IPv6 packets in xt_LOG, from Michal Kubecek.
This bug has been there since 2.6.26.
* Fix breakage ip_vs_sh due to incorrect structure layout for
RCU, from Jan Beulich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- reduce broadcast overhead on non-lossy wired links
- fix typos in kernel doc
- use eth_hdr() when possible
- use netdev_allock_skb_ip_align() and don't deal with NET_IP_ALIGN
- change VID semantic in the BLA component
- other minor cleanups and code refactoring
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJRpVCoAAoJEADl0hg6qKeOC0MP/ROgdprMTQNSFnvJLo9YZ4qP
EZpEwPqU8gCmnOKdQJ/KYSiyAX/iFjwTBgfelq1ekAbUmzV1y/cLOjHgZuOhM7Bk
5xEiC5Yunj+5Q14f1rW6uDs8+B84gnl4Iow9j6aAlOW6g0BAf3Pb9caN7sSheh/w
dKUHQKaDHaNMrHVerEHRDkzlWSJes6YIYMKgbX1mwMGddMtFJbMKIvylzilLXUl6
3jLlwC8XDvgH+0ygLvuFWEhOwkSdWTo32J92VE/WSTpDPyZYvXj/r+/e/U2Pi3q2
2owariF4PCr+4cc2tcDOPIh/zRdt0OTCZ2lW/z2CZbCCGZ3AYoQ8ue4hulf9AyZS
9Ff/wdgMmPN/aM+t7+QtKrKAcCBb9JqY3eVRL6jeBUF+SP0O/dfVDaQreQExy+iF
H0LhsE6eqMFaucjZit/yZ2SpR6kMo42BmCZjLJVujm0REUsqaq3GKolzrRGNDX91
Wzc/eZkqyES3R6rMrbvW0iqRAAPiUi6YOv9f8MoYbqXNOcmJJdyoMVWthAEFOnFB
4qJw2O5HlROL2TmOKw7cR4TPDX9reWN0OdZrSLabEXYkqVhoqB08ojSLAZbHVTe4
h3EEjGc8eaIpAYb5B68JE41ZNEZFIUlwOCMxeZsk2LV05LTOHCmrUPbF+n/psag9
9zt30TKyPu2b/+XFyOfd
=22js
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- reduce broadcast overhead on non-lossy wired links
- fix typos in kernel doc
- use eth_hdr() when possible
- use netdev_allock_skb_ip_align() and don't deal with NET_IP_ALIGN
- change VID semantic in the BLA component
- other minor cleanups and code refactoring
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_rcu() requires offsetof(..., rcu_head) < 4096, which can
get violated with a sufficiently high CONFIG_IP_VS_SH_TAB_BITS.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As of f025adf191 "sunrpc: Properly decode
kuids and kgids in RPC_AUTH_UNIX credentials" any rpc containing a -1
(0xffff) uid or gid would fail with a badcred error.
Reported symptoms were xmbc clients failing on upgrade of the NFS
server; examination of the network trace showed them sending -1 as the
gid.
Reported-by: Julian Sikorski <belegdol@gmail.com>
Tested-by: Julian Sikorski <belegdol@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
While l2cap_user callbacks are running, the whole hci_dev is locked. Even
if we would add more fine-grained locking to HCI core, it would still be
called from the non-reentrant rx work-queue and thus block the event
processing.
However, if we want to perform synchronous I/O during HID device
registration (eg., to perform device-detection), we need the HCI core
to be able to dispatch incoming data.
Therefore, we now move device-registration to a separate worker. The HCI
core can continue running and we add devices asynchronously in another
kernel thread. Device removal is synchronized and waits for the worker
to exit before calling the usual device removal functions.
If l2cap_user->remove is called before the thread registered the devices,
we set "terminate" to true and the thread will skip it. If
l2cap_user->remove is called after it, we notice this as the device
is no longer in HIDP_SESSION_PREPARING state and simply unregister the
device as we did before.
There is no new deadlock as we now call hidp_session_add_dev() with
one lock less held (the HCI lock) and it cannot itself call back into
HCI as it was called with the HCI-lock held before.
One might wonder whether this can block during device unregistration.
But we set "terminate" to true and wake the HIDP thread up _before_
unregistering the HID/input devices. Therefore, all pending HID I/O
operations are canceled. All further I/O attempts will fail with ENODEV
or EIO. So all latency we can get are few context-switches, but no
timeouts or blocking I/O waits!
This change also prepares for a long standing HID bug. All HID devices
that register power_supply devices need to be able to handle callbacks
during registration (a power_supply oddity that cannot easily be fixed).
So with this patch available, we can allow HID I/O during registration
by calling the recently introduced hid_device_io_start/stop helpers,
which currently are a no-op for bluetooth due to this locking.
Note that we cannot do the same for input devices. input-core doesn't
allow us to call input_event() asynchronously to input_register_device(),
which HID-core kindly allows (for good reasons).
Fixing input-core to allow this isn't as easy as it sounds and is,
beside simplifying HIDP, not really an improvement. Hence, we still
register input devices synchronously as we did before. Only HID devices
are registered asynchronously.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Daniel Nicoletti <dantti12@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In dump_ipv6_packet(), the "recurse" parameter is zero only if
dumping contents of a packet embedded into an ICMPv6 error
message. Therefore we want to log packet mark if recurse is
non-zero, not when it is zero.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the driver advertised support for a CAB queue, then we
should put all multicast frames there, otherwise sending
them can be racy with clients going to sleep while we TX
a frame. To avoid this, always TX multicast frames on the
multicast queue.
It seems like even drivers not using the queue framework
might want to do this which would mean also moving the
IEEE80211_TX_CTL_SEND_AFTER_DTIM flag assignment, but it
also seems that drivers behave differently here so that
just moving it wouldn't be a good idea. It'd be better to
modify those drivers to use the queue framework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support them only if the driver advertises support for them via
IEEE80211_HW_SUPPORTS_ACTIVE_MONITOR. Unlike normal monitor interfaces,
they are added to the driver, along with their MAC address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The three arrays of strings: af_family_key_strings,
af_family_slock_key_strings and af_family_clock_key_strings have not
VSOCK's string
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To: linux-kernel@vger.kernel.org
Cc: x86@kernel.org, trinity@vger.kernel.org, Andy Lutomirski <luto@amacapital.net>, netdev@vger.kernel.org, "David S.
Miller" <davem@davemloft.net>
Subject: [PATCH 5/5] net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg
MSG_CMSG_COMPAT is (AFAIK) not intended to be part of the API --
it's a hack that steals a bit to indicate to other networking code
that a compat entry was used. So don't allow it from a non-compat
syscall.
This prevents an oops when running this code:
int main()
{
int s;
struct sockaddr_in addr;
struct msghdr *hdr;
char *highpage = mmap((void*)(TASK_SIZE_MAX - 4096), 4096,
PROT_READ | PROT_WRITE,
MAP_PRIVATE | MAP_ANONYMOUS | MAP_FIXED, -1, 0);
if (highpage == MAP_FAILED)
err(1, "mmap");
s = socket(AF_INET, SOCK_DGRAM, IPPROTO_UDP);
if (s == -1)
err(1, "socket");
addr.sin_family = AF_INET;
addr.sin_port = htons(1);
addr.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
if (connect(s, (struct sockaddr*)&addr, sizeof(addr)) != 0)
err(1, "connect");
void *evil = highpage + 4096 - COMPAT_MSGHDR_SIZE;
printf("Evil address is %p\n", evil);
if (syscall(__NR_sendmmsg, s, evil, 1, MSG_CMSG_COMPAT) < 0)
err(1, "sendmmsg");
return 0;
}
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer however skb->network_header is now
an offset.
This patch corrects the problem by adding a wrapper to return skb tail as
an offset regardless of the value of NET_SKBUFF_DATA_USES_OFFSET. It seems
that skb->tail that this offset may be more than 64k and some care has been
taken to treat such cases as an error.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case sk_buff_data_t will be a pointer, however,
skb->{network,transport}_header is now __u16.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 351638e7de (net: pass info struct via netdevice notifier)
breaks booting of my KVM guest, this is due to we still forget to pass
struct netdev_notifier_info in several places. This patch completes it.
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to batadv_nc_skb_forward() fits better in
batadv_send_skb_to_orig(), as this is where the actual next hop is
looked up.
To let the caller of batadv_send_skb_to_orig() know wether the skb is
transmitted, buffered or failed, the return value is changed from
boolean to int.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Since the MSB bits of any vid variable are now used for
storing flags, print the vid properly by taking the flags
away and printing -1 in case of VID representing no real
VLAN.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
In order to make batman-adv fully vlan aware later, the
semantic used for variables storing the VLAN ID values has
to be changed in order to be adapted to the new one which
will be used batman-adv wide.
In particular, the VID has to be an "_unsigned_ short int"
and its 4 MSB will be used as a flag bitfield, while the
remaining 12 bits are used to store the real VID value
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
There's no need to for an explicit hlist_node initialization if it is
added to a list right away, like it's the case with the
hlist_add_head()s here.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
it may be the case that we want to store some local TT client flags in a global
entry, therefore the tt_global_add needs to get a proper argument for this
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Instead of dealing with NET_IP_ALIGN during allocation and
headroom reservation, it is possible to use
netdev_alloc_skb_ip_align() which transparently allocate
and reserve the correct amount of data
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Instead of passing a generic combination of flags as
argument, it is easier to pass the entire tt_common
structure (containing the flags already set) plus a
bitfield of event flags that will be unified with
the already existing ones before inserting the client
in the event queue.
In this way invocations of the modified function can be
simplified.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
batadv_slide_own_bcast_window() is used only in bat_iv_ogm.c
and it is currently touching only batman_iv specific
attributes.
Move it into bat_iv_ogm.c and make it static.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
the two lonely ring_buffer helper functions are used by the
bat_iv_ogm module only and therefore they can be moved
inside it.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Instead of casting the result of skb_mac_header() to
"struct ethhdr *" every time, the eth_hdr inline function
can be use to beautify the code and improve its readability.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
hard-interface.c has to do not contain any routing algorithm
specific code.
Allocate the hard-interface with kzalloc() and remove any
useless and algorithm specific member initialisation
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Only one neigh_node per orig_node should match a given
neighbor address, therefore, if more than one matching
neigh_node is found, a WARNING has to be triggered to let
the user know that something is wrong in the originator
state instead of silently skipping the error.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Compatibility version is checked upon packet reception
before calling any handler. For this reason it does need to
be checked once more in the handler itself.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The source address has already been checked in
batadv_check_management_packet() upon packet reception and
therefore it does not need to be checked again in
ogm_process()
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
print the interface along with the new neighbor mac address
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
the sequence number is not stored in struct neigh_node,
therefore there is no need to pass such value to the
neigh_node creation procedure.
At the moment the value is only used by a debug message, but
given the fact that the seqno is not related to the neighbor
object, it is better to print it elsewhere.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
While it makes sense to send each broadcast thrice on 802.11 (WLAN) interfaces
as broadcasts are often unreliable on these, there is no reason to do so on
other interface types.
The increased the overhead can be harmful on low-bandwidth links like VPN
connections over slow internet lines, therefore it is better to reduce the
number of broadcast packets sent on non-wireless links to one.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Previously batadv_is_wifi_iface() did two things at once: looking up a
net_device from an interface index, and determining if it is a wifi device.
The second part is useful itself when the caller already has a net_device
reference.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Somebody noticed LTP was complaining about O_NONBLOCK opens of
/proc/net/rpc/use-gss-proxy succeeding and then a following read
hanging.
I'm not convinced LTP really has any business opening random proc files
and expecting them to behave a certain way. Maybe this isn't really a
bug.
But in any case the O_NONBLOCK behavior could be useful for someone that
wants to test whether gss-proxy is up without waiting.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
net/core/skbuff.c: In function ‘__alloc_skb_head’:
net/core/skbuff.c:203:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c: In function ‘__alloc_skb’:
net/core/skbuff.c:279:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c:280:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c: In function ‘build_skb’:
net/core/skbuff.c:348:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c:349:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Signed-off-by: David S. Miller <davem@davemloft.net>
IFF_NOARP affects what kind of neighbor entries are created
(nud NOARP or nud INCOMPLETE). If the flag changes, flush the arp
cache to refresh all entries.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: shortened notifier_info struct name
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new netdevice notifier infrastructure to pass along changed flags.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: shortened notifier_info struct name
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
For zero copy request, error will be encoded in the user space buffer.
So copy the error code correctly using copy_from_user. Here we use the
extra bytes we allocate for zero copy request. If total error details
are more than P9_ZC_HDR_SZ - 7 bytes, we return -EFAULT. The patch also
avoid a memory allocation in the error path.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
For zero copy request, error will be encoded in the user space buffer.
So copy the error code correctly using copy_from_user. Here we use the
extra bytes we allocate for zero copy request. If total error details
are more than P9_ZC_HDR_SZ - 7 bytes, we return -EFAULT. The patch also
avoid a memory allocation in the error path.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Make the default 9p experience better by defaulting to virtio transport if present.
These days most of the users are using 9p in a virtualized setup
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
If we dont' specify a protocol version default to 9P2000.L. 9P2000.L
have better support for posix semantic and is where all the recent development
is happening.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Unlike ipv4_redirect() and ipv4_sk_redirect(), ip_do_redirect()
doesn't call __build_flow_key() directly but via
ip_rt_build_flow_key() wrapper. This leads to __build_flow_key()
getting pointer to IPv4 header of the ICMP redirect packet
rather than pointer to the embedded IPv4 header of the packet
initiating the redirect.
As a result, handling of ICMP redirects initiated by TCP packets
is broken. Issue was introduced by
4895c771c ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll_rx_disable() will always return 0, it is no use and looks wordy,
so remove the unnecessary code and get rid of it in _dev_open and _dev_close.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where a non-MPLS packet is received and an MPLS stack is
added it may well be the case that the original skb is GSO but the
NIC used for transmit does not support GSO of MPLS packets.
The aim of this code is to provide GSO in software for MPLS packets
whose skbs are GSO.
SKB Usage:
When an implementation adds an MPLS stack to a non-MPLS packet it should do
the following to skb metadata:
* Set skb->inner_protocol to the old non-MPLS ethertype of the packet.
skb->inner_protocol is added by this patch.
* Set skb->protocol to the new MPLS ethertype of the packet.
* Set skb->network_header to correspond to the
end of the L3 header, including the MPLS label stack.
I have posted a patch, "[PATCH v3.29] datapath: Add basic MPLS support to
kernel" which adds MPLS support to the kernel datapath of Open vSwtich.
That patch sets the above requirements in datapath/actions.c:push_mpls()
and was used to exercise this code. The datapath patch is against the Open
vSwtich tree but it is intended that it be added to the Open vSwtich code
present in the mainline Linux kernel at some point.
Features:
I believe that the approach that I have taken is at least partially
consistent with the handling of other protocols. Jesse, I understand that
you have some ideas here. I am more than happy to change my implementation.
This patch adds dev->mpls_features which may be used by devices
to advertise features supported for MPLS packets.
A new NETIF_F_MPLS_GSO feature is added for devices which support
hardware MPLS GSO offload. Currently no devices support this
and MPLS GSO always falls back to software.
Alternate Implementation:
One possible alternate implementation is to teach netif_skb_features()
and skb_network_protocol() about MPLS, in a similar way to their
understanding of VLANs. I believe this would avoid the need
for net/mpls/mpls_gso.c and in particular the calls to
__skb_push() and __skb_push() in mpls_gso_segment().
I have decided on the implementation in this patch as it should
not introduce any overhead in the case where mpls_gso is not compiled
into the kernel or inserted as a module.
MPLS GSO suggested by Jesse Gross.
Based in part on "v4 GRE: Add TCP segmentation offload for GRE"
by Pravin B Shelar.
Cc: Jesse Gross <jesse@nicira.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the current WoWLAN configuration available to drivers
at runtime. This isn't really useful for the normal WoWLAN
behaviour and accessing it can also be racy, but drivers
may use it for testing the WoWLAN device behaviour while
the host stays up & running to observe the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FTP conntrack code currently only accepts the following format for
the 227 response for PASV:
227 Entering Passive Mode (148,100,81,40,31,161).
It doesn't accept the following format from an obscure server:
227 Data transfer will passively listen to 67,218,99,134,50,144
From RFC 1123:
The format of the 227 reply to a PASV command is not
well standardized. In particular, an FTP client cannot
assume that the parentheses shown on page 40 of RFC-959
will be present (and in fact, Figure 3 on page 43 omits
them). Therefore, a User-FTP program that interprets
the PASV reply must scan the reply for the first digit
of the host and port numbers.
This patch adds support for the RFC 1123 clarification by:
- Allowing a search filter to specify NUL as the terminator so that
try_number will return successfully if the array of numbers has been
filled when an unexpected character is encountered.
- Using space as the separator for the 227 reply and then scanning for
the first digit of the number sequence. The number sequence is parsed
out using the existing try_rfc959 but with a NUL terminator.
References: https://bugzilla.novell.com/show_bug.cgi?id=466279
References: http://bugzilla.netfilter.org/show_bug.cgi?id=574
Reported-by: Mark Post <mpost@novell.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netfilter-devel@vger.kernel.org
Cc: netfilter@vger.kernel.org
Cc: coreteam@netfilter.org
Cc: netdev@vger.kernel.org
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Expire cached connection for new TCP/SCTP connection if real
server is down. Otherwise, IPVS uses the dead server for the
reused connection, instead of a new working one.
Signed-off-by: Grzegorz Lyczba <grzegorz.lyczba@gmail.com>
Acked-by: Hans Schillstrom <hans@schillstrom.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When changing the MAC address of a single vif mac80211 will check if
the new address fits into the address mask specified by the driver.
This only needs to be done when using multiple BSSIDs. Hence, check
the new address only against all other vifs.
Also fix the MAC address assignment on new interfaces if the user
changed the address of a vif such that perm_addr is not covered by
addr_mask anymore.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=57371
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Bruno Randolf <br1@thinktube.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The portid is set to NETLINK_CB(skb).portid at create time.
The run-time check will always be false.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- Stable fix to prevent an rpc_task wakeup race
- Fix a NFSv4.1 session drain deadlock
- Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
- Ensure auth_gss pipe detection works in namespaces
- Fix SETCLIENTID fallback if rpcsec_gss is not available
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=B8go
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix to prevent an rpc_task wakeup race
- Fix a NFSv4.1 session drain deadlock
- Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
- Ensure auth_gss pipe detection works in namespaces
- Fix SETCLIENTID fallback if rpcsec_gss is not available
* tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix SETCLIENTID fallback if GSS is not available
SUNRPC: Prevent an rpc_task wakeup race
NFSv4.1 Fix a pNFS session draining deadlock
SUNRPC: Convert auth_gss pipe detection to work in namespaces
SUNRPC: Faster detection if gssd is actually running
SUNRPC: Fix a bug in gss_create_upcall
Daniel Petre reported crashes in icmp_dst_unreach() with following call
graph:
#3 [ffff88003fc03938] __stack_chk_fail at ffffffff81037f77
#4 [ffff88003fc03948] icmp_send at ffffffff814d5fec
#5 [ffff88003fc03ae8] ipv4_link_failure at ffffffff814a1795
#6 [ffff88003fc03af8] ipgre_tunnel_xmit at ffffffff814e7965
#7 [ffff88003fc03b78] dev_hard_start_xmit at ffffffff8146e032
#8 [ffff88003fc03bc8] sch_direct_xmit at ffffffff81487d66
#9 [ffff88003fc03c08] __qdisc_run at ffffffff81487efd
#10 [ffff88003fc03c48] dev_queue_xmit at ffffffff8146e5a7
#11 [ffff88003fc03c88] ip_finish_output at ffffffff814ab596
Daniel found a similar problem mentioned in
http://lkml.indiana.edu/hypermail/linux/kernel/1007.0/00961.html
And indeed this is the root cause : skb->cb[] contains data fooling IP
stack.
We must clear IPCB in ip_tunnel_xmit() sooner in case dst_link_failure()
is called. Or else skb->cb[] might contain garbage from GSO segmentation
layer.
A similar fix was tested on linux-3.9, but gre code was refactored in
linux-3.10. I'll send patches for stable kernels as well.
Many thanks to Daniel for providing reports, patches and testing !
Reported-by: Daniel Petre <daniel.petre@rcs-rds.ro>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
case TCP_FIN_WAIT1 can also be simplified by reversing tests
and adding breaks;
Add braces after case and move automatic definitions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
case TCP_SYN_RECV: can have another indentation level removed
by converting
if (acceptable) {
...;
} else {
return 1;
}
to
if (!acceptable)
return 1;
...;
Reflow code and comments to fit 80 columns.
Another pure cleanup patch.
Signed-off-by: Joe Perches <joe@perches.com>
Improved-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove one level of indentation 'introduced' in commit
c3ae62af8e (tcp: should drop incoming frames without ACK flag set)
if (true) {
...
}
@acceptable variable is a boolean.
This patch is a pure cleanup.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when upper device is changed, event is not propagated via RT Netlink
to userspace. Userspace might never now about the change. Fix this by
adding upper-device-change notifier event.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability to send ICMPv6 echo requests without a
raw socket. The equivalent ability for ICMPv4 was added in
2011.
Instead of having separate code paths for IPv4 and IPv6, make
most of the code in net/ipv4/ping.c dual-stack and only add a
few IPv6-specific bits (like the protocol definition) to a new
net/ipv6/ping.c. Hopefully this will reduce divergence and/or
duplication of bugs in the future.
Caveats:
- Setting options via ancillary data (e.g., using IPV6_PKTINFO
to specify the outgoing interface) is not yet supported.
- There are no separate security settings for IPv4 and IPv6;
everything is controlled by /proc/net/ipv4/ping_group_range.
- The proc interface does not yet display IPv6 ping sockets
properly.
Tested with a patched copy of ping6 and using raw socket calls.
Compiles and works with all of CONFIG_IPV6={n,m,y}.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This member of struct netns_ipvs is calculated from nr_free_buffer_pages
so change its type to unsigned long in case of overflow. Also, type of
its related proc var sync_qlen_max and the return type of function
sysctl_sync_qlen_max() should be changed to unsigned long, too.
Besides, the type of ipvs_master_sync_state->sync_queue_len should be
changed to unsigned long accordingly.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_mutex is similar to the ones I just removed in
cfg80211 but even less useful since it protects global
data, and we hold the RTNL in all places (except module
unload) already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since it just does a quick check of the last regulatory
request, the function doesn't have to hold the reg mutex
but can use RCU instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver for some reason successfully finishes
scanning while in p2p_stop_device(), cfg80211 will
still set it to aborted. Simplify this code using the
new 'notified' value and only mark it aborted in case
the driver didn't notify cfg80211 at all (in which
case we also leak the request to not crash, this is
a driver bug.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As estab_plinks is not a statistics member, don't show its debug information
along with other mesh stat members
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
"It's been a while since my last pull request so quite a few fixes have
piled up."
Indeed.
1) Fix nf_{log,queue} compilation with PROC_FS disabled, from Pablo
Neira Ayuso.
2) Fix data corruption on some tg3 chips with TSO enabled, from Michael
Chan.
3) Fix double insertion of VLAN tags in be2net driver, from Sarveshwar
Bandi.
4) Don't have TCP's MD5 support pass > PAGE_SIZE page offsets in
scatter-gather entries into the crypto layer, the crypto layer can't
handle that. From Eric Dumazet.
5) Fix lockdep splat in 802.1Q MRP code, also from Eric Dumazet.
6) Fix OOPS in netfilter log module when called from conntrack, from
Hans Schillstrom.
7) FEC driver needs to use netif_tx_{lock,unlock}_bh() rather than the
non-BH disabling variants. From Fabio Estevam.
8) TCP GSO can generate out-of-order packets, fix from Eric Dumazet.
9) vxlan driver doesn't update 'used' field of fdb entries when it
should, from Sridhar Samudrala.
10) ipv6 should use kzalloc() to allocate inet6 socket cork options,
otherwise we can OOPS in ip6_cork_release(). From Eric Dumazet.
11) Fix races in bonding set mode, from Nikolay Aleksandrov.
12) Fix checksum generation regression added by "r8169: fix 8168evl
frame padding.", from Francois Romieu.
13) ip_gre can look at stale SKB data pointer, fix from Eric Dumazet.
14) Fix checksum handling when GSO is enabled in bnx2x driver with
certain chips, from Yuval Mintz.
15) Fix double free in batman-adv, from Martin Hundebøll.
16) Fix device startup synchronization with firmware in tg3 driver, from
Nithin Sujit.
17) perf networking dropmonitor doesn't work at all due to mixed up
trace parameter ordering, from Ben Hutchings.
18) Fix proportional rate reduction handling in tcp_ack(), from Nandita
Dukkipati.
19) IPSEC layer doesn't return an error when a valid state is detected,
causing an OOPS. Fix from Timo Teräs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (85 commits)
be2net: bug fix on returning an invalid nic descriptor
tcp: xps: fix reordering issues
net: Revert unused variable changes.
xfrm: properly handle invalid states as an error
virtio_net: enable napi for all possible queues during open
tcp: bug fix in proportional rate reduction.
net: ethernet: sun: drop unused variable
net: ethernet: korina: drop unused variable
net: ethernet: apple: drop unused variable
qmi_wwan: Added support for Cinterion's PLxx WWAN Interface
perf: net_dropmonitor: Remove progress indicator
perf: net_dropmonitor: Use bisection in symbol lookup
perf: net_dropmonitor: Do not assume ordering of dictionaries
perf: net_dropmonitor: Fix symbol-relative addresses
perf: net_dropmonitor: Fix trace parameter order
net: fec: use a more proper compatible string for MVF type device
qlcnic: Fix updating netdev->features
qlcnic: remove netdev->trans_start updates within the driver
qlcnic: Return proper error codes from probe failure paths
tg3: Update version to 3.132
...
Some chips can tell us if received frame was
encoded with STBC or not. To make this information available
in user space we can use updated radiotap specification:
http://www.radiotap.org/defined-fields/MCS
This patch will set number of STBC encoded spatial streams (Nss).
The HAVE_STBC flag should be provided by driver.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When vlan device is configured on top of the brige, it does
not support any offload capabilities because the bridge
device does not initiliaze vlan_fatures. Set vlan_fatures to
be equivalent to hw_fatures.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 3853b5841c ("xps: Improvements in TX queue selection")
introduced ooo_okay flag, but the condition to set it is slightly wrong.
In our traces, we have seen ACK packets being received out of order,
and RST packets sent in response.
We should test if we have any packets still in host queue.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.
To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.
For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.
For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.
Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If nf_log uses ipt_ULOG as logging output, we can deliver non-null
terminated strings to user-space since the maximum length of the
prefix that is passed by nf_log is NF_LOG_PREFIXLEN but pm->prefix
is 32 bytes long (ULOG_PREFIX_LEN).
This is actually happening already from nf_conntrack_tcp if ipt_ULOG
is used, since it is passing strings longer than 32 bytes.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This avoids the situation where walking of a large number of connections
may prevent scheduling for a long time while also avoiding excessive
calls to rcu_read_unlock() and rcu_read_lock().
Note that in the case of !CONFIG_PREEMPT_RCU this will
add a call to cond_resched().
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This target has been superseded by NFLOG. Spot a warning
so we prepare removal in a couple of years.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
Don't panic if we hit an error while adding the nf_log or pernet
netfilter support, just bail out.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
Quoting https://bugzilla.netfilter.org/show_bug.cgi?id=812:
[ ip6tables -m addrtype ]
When I tried to use in the nat/PREROUTING it messes up the
routing cache even if the rule didn't matched at all.
[..]
If I remove the --limit-iface-in from the non-working scenario, so just
use the -m addrtype --dst-type LOCAL it works!
This happens when LOCAL type matching is requested with --limit-iface-in,
and the default ipv6 route is via the interface the packet we test
arrived on.
Because xt_addrtype uses ip6_route_output, the ipv6 routing implementation
creates an unwanted cached entry, and the packet won't make it to the
real/expected destination.
Silently ignoring --limit-iface-in makes the routing work but it breaks
rule matching (--dst-type LOCAL with limit-iface-in is supposed to only
match if the dst address is configured on the incoming interface;
without --limit-iface-in it will match if the address is reachable
via lo).
The test should call ipv6_chk_addr() instead. However, this would add
a link-time dependency on ipv6.
There are two possible solutions:
1) Revert the commit that moved ipt_addrtype to xt_addrtype,
and put ipv6 specific code into ip6t_addrtype.
2) add new "nf_ipv6_ops" struct to register pointers to ipv6 functions.
While the former might seem preferable, Pablo pointed out that there
are more xt modules with link-time dependeny issues regarding ipv6,
so lets go for 2).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
'name' has already set all zero when it is defined, so not need let
strncpy() to pad it again.
'name' is a string, better always let is NUL terminated, so use
strlcpy() instead of strncpy().
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With IP early demux added in linux-3.6, we perform TCP lookup in IP
layer before iptables hooks.
We can avoid doing a second lookup in xt_socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The percpu untracked ct are not currently used for XT_CT_NOTRACK.
xt_ct_tg_check()/xt_ct_target() provides a single ct.
Thats not optimal as the ct->ct_general.use cache line will bounce among
cpus.
Use the intended [1] thing : xt_ct_target() should select the percpu
object.
[1] Refs :
commit 5bfddbd46a ("netfilter: nf_conntrack: IPS_UNTRACKED bit")
commit b3c5163fe0 ("netfilter: nf_conntrack: per_cpu untracking")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The error exit path needs err explicitly set. Otherwise it
returns success and the only caller, xfrm_output_resume(),
would oops in skb_dst(skb)->ops derefence as skb_dst(skb) is
NULL.
Bug introduced in commit bb65a9cb (xfrm: removes a superfluous
check and add a statistic).
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_addr_type(&addr)&IPV6_ADDR_SCOPE_MASK could be replaced
by ipv6_addr_scope(), which is slightly faster.
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_addr_any() is a faster way to determine if an addr
is ipv6 any addr, no need to compute the addr type.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a fix for a bug triggering newly_acked_sacked < 0
in tcp_ack(.).
The bug is triggered by sacked_out decreasing relative to prior_sacked,
but packets_out remaining the same as pior_packets. This is because the
snapshot of prior_packets is taken after tcp_sacktag_write_queue() while
prior_sacked is captured before tcp_sacktag_write_queue(). The problem
is: tcp_sacktag_write_queue (tcp_match_skb_to_sack() -> tcp_fragment)
adjusts the pcount for packets_out and sacked_out (MSS change or other
reason). As a result, this delta in pcount is reflected in
(prior_sacked - sacked_out) but not in (prior_packets - packets_out).
This patch does the following:
1) initializes prior_packets at the start of tcp_ack() so as to
capture the delta in packets_out created by tcp_fragment.
2) introduces a new "previous_packets_out" variable that snapshots
packets_out right before tcp_clean_rtx_queue, so pkts_acked can be
correctly computed as before.
3) Computes pkts_acked using previous_packets_out, and computes
newly_acked_sacked using prior_packets.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a GSO packet has a length above tbf burst limit, the packet
is currently silently dropped.
Current way to handle this is to set the device in non GSO/TSO mode, or
setting high bursts, and its sub optimal.
We can actually segment too big GSO packets, and send individual
segments as tbf parameters allow, allowing for better interoperability.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a generic solution to resolve a specific problem that I have observed.
If the encapsulation of an skb changes then ability to offload checksums
may also change. In particular it may be necessary to perform checksumming
in software.
An example of such a case is where a non-GRE packet is received but
is to be encapsulated and transmitted as GRE.
Another example relates to my proposed support for for packets
that are non-MPLS when received but MPLS when transmitted.
The cost of this change is that the value of the csum variable may be
checked when it previously was not. In the case where the csum variable is
true this is pure overhead. In the case where the csum variable is false it
leads to software checksumming, which I believe also leads to correct
checksums in transmitted packets for the cases described above.
Further analysis:
This patch relies on the return value of can_checksum_protocol()
being correct and in turn the return value of skb_network_protocol(),
used to provide the protocol parameter of can_checksum_protocol(),
being correct. It also relies on the features passed to skb_segment()
and in turn to can_checksum_protocol() being correct.
I believe that this problem has not been observed for VLANs because it
appears that almost all drivers, the exception being xgbe, set
vlan_features such that that the checksum offload support for VLAN packets
is greater than or equal to that of non-VLAN packets.
I wonder if the code in xgbe may be an oversight and the hardware does
support checksumming of VLAN packets. If so it may be worth updating the
vlan_features of the driver as this patch will force such checksums to be
performed in software rather than hardware.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue sending queries when leave is received if the user marks
it as a querier.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we arm the expire timer when the mdb entry is added,
however, this causes problem when there is no querier sent
out after that.
So we should only arm the timer when a corresponding query is
received, as suggested by Herbert.
And he also mentioned "if there is no querier then group
subscriptions shouldn't expire. There has to be at least one querier
in the network for this thing to work. Otherwise it just degenerates
into a non-snooping switch, which is OK."
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quote from Adam:
"If it is believed that the use of 0.0.0.0
as the IP address is what is causing strange behaviour on other devices
then is there a good reason that a bridge rather than a router shouldn't
be the active querier? If not then using the bridge IP address and
having the querier enabled by default may be a reasonable solution
(provided that our querier obeys the election rules and shuts up if it
sees a query from a lower IP address that isn't 0.0.0.0). Just because a
device is the elected querier for IGMP doesn't appear to mean it is
required to perform any other routing functions."
And introduce a new troggle for it, as suggested by Herbert.
Suggested-by: Adam Baker <linux@baker-net.org.uk>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lockless RPC_IS_QUEUED() test in __rpc_execute means that we need to
be careful about ordering the calls to rpc_test_and_set_running(task) and
rpc_clear_queued(task). If we get the order wrong, then we may end up
testing the RPC_TASK_RUNNING flag after __rpc_execute() has looped
and changed the state of the rpc_task.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
On errors in batadv_mesh_init(), bat_counters will be freed in both
batadv_mesh_free() and batadv_softif_init_late(). This patch fixes this
by returning earlier from batadv_softif_init_late() in case of errors in
batadv_mesh_init() and by setting bat_counters to NULL after freeing.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The cache_detail(*detail) in function cache_is_valid is not used any
more.
Signed-off-by: fanchaoting <fanchaoting@cn.fujitsu.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The Kconfig symbol NFC_LLCP was removed in commit 30cc458765 ("NFC: Move
LLCP code to the NFC top level diirectory"). But the reference to its
macro in this Makefile was only commented out. Remove it now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TCP md5 code uses per cpu variables but protects access to them with
a shared spinlock, which is a contention point.
[ tcp_md5sig_pool_lock is locked twice per incoming packet ]
Makes things much simpler, by allocating crypto structures once, first
time a socket needs md5 keys, and not deallocating them as they are
really small.
Next step would be to allow crypto allocations being done in a NUMA
aware way.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A cpu executing the network receive path sheds packets when its input
queue grows to netdev_max_backlog. A single high rate flow (such as a
spoofed source DoS) can exceed a single cpu processing rate and will
degrade throughput of other flows hashed onto the same cpu.
This patch adds a more fine grained hashtable. If the netdev backlog
is above a threshold, IRQ cpus track the ratio of total traffic of
each flow (using 4096 buckets, configurable). The ratio is measured
by counting the number of packets per flow over the last 256 packets
from the source cpu. Any flow that occupies a large fraction of this
(set at 50%) will see packet drop while above the threshold.
Tested:
Setup is a muli-threaded UDP echo server with network rx IRQ on cpu0,
kernel receive (RPS) on cpu0 and application threads on cpus 2--7
each handling 20k req/s. Throughput halves when hit with a 400 kpps
antagonist storm. With this patch applied, antagonist overload is
dropped and the server processes its complete load.
The patch is effective when kernel receive processing is the
bottleneck. The above RPS scenario is a extreme, but the same is
reached with RFS and sufficient kernel processing (iptables, packet
socket tap, ..).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another fix needed in ipgre_err(), as parse_gre_header() might change
skb->head.
Bug added in commit c544193214 (GRE: Refactor GRE tunneling code.)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_timeout_skb() was intended to trigger fast recovery on timeout,
unfortunately in reality it often causes spurious retransmission
storms during fast recovery. The particular sign is a fast retransmit
over the highest sacked sequence (SND.FACK).
Currently the RTO timer re-arming (as in RFC6298) offers a nice cushion
to avoid spurious timeout: when SND.UNA advances the sender re-arms
RTO and extends the timeout by icsk_rto. The sender does not offset
the time elapsed since the packet at SND.UNA was sent.
But if the next (DUP)ACK arrives later than ~RTTVAR and triggers
tcp_fastretrans_alert(), then tcp_timeout_skb() will mark any packet
sent before the icsk_rto interval lost, including one that's above the
highest sacked sequence. Most likely a large part of scorebard will be
marked.
If most packets are not lost then the subsequent DUPACKs with new SACK
blocks will cause the sender to continue to retransmit packets beyond
SND.FACK spuriously. Even if only one packet is lost the sender may
falsely retransmit almost the entire window.
The situation becomes common in the world of bufferbloat: the RTT
continues to grow as the queue builds up but RTTVAR remains small and
close to the minimum 200ms. If a data packet is lost and the DUPACK
triggered by the next data packet is slightly delayed, then a spurious
retransmission storm forms.
As the original comment on tcp_timeout_skb() suggests: the usefulness
of this feature is questionable. It also wastes cycles walking the
sack scoreboard and is actually harmful because of false recovery.
It's time to remove this.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: "memcpy_fromiovec" [drivers/vhost/vhost_scsi.ko] undefined!
That function is only present with CONFIG_NET. Turns out that
crypto/algif_skcipher.c also uses that outside net, but it actually
needs sockets anyway.
In addition, commit 6d4f0139d6 added
CONFIG_NET dependency to CONFIG_VMCI for memcpy_toiovec, so hoist
that function and revert that commit too.
socket.h already includes uio.h, so no callers need updating; trying
only broke things fo x86_64 randconfig (thanks Fengguang!).
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
'discovery->data.info' length is 22, NICKNAME_MAX_LEN is 21, so the
strncpy() will always left the last byte of 'discovery->data.info'
uninitialized.
When 'text' length is longer than 21 (NICKNAME_MAX_LEN), if still left
the last byte of 'discovery->data.info' uninitialized, the next
strlen() will cause issue.
Also 'discovery->data' is 'struct irda_device_info' which defined in
"include/uapi/...", it may copy to user mode, so need whole initialized.
All together, need use kzalloc() instead of kmalloc() to initialize all
members firstly.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of peer address for IPv6. For example, it is
possible to specify the remote end of a 6inY tunnel.
This was already possible in IPv4:
ip addr add ip1 peer ip2 dev dev1
The peer address is specified with IFA_ADDRESS and the local address with
IFA_LOCAL (like explained in include/uapi/linux/if_addr.h).
Note that the API is not changed, because before this patch, it was not
possible to specify two different addresses in IFA_LOCAL and IFA_REMOTE.
There is a small change for the dump: if the peer is different from ::,
IFA_ADDRESS will contain the peer address instead of the local address.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net/netlabel/netlabel_domainhash.c:netlbl_domhsh_add() function
does not properly validate new domain hash entries resulting in
potential problems when an administrator attempts to add an invalid
entry. One such problem, as reported by Vlad Halilov, is a kernel
BUG (found in netlabel_domainhash.c:netlbl_domhsh_audit_add()) when
adding an IPv6 outbound mapping with a CIPSO configuration.
This patch corrects this problem by adding the necessary validation
code to netlbl_domhsh_add() via the newly created
netlbl_domhsh_validate() function.
Ideally this patch should also be pushed to the currently active
-stable trees.
Reported-by: Vlad Halilov <vlad.halilov@gmail.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0178b695fd ("ipv6: Copy cork options in ip6_append_data")
added some code duplication and bad error recovery, leading to potential
crash in ip6_cork_release() as kfree() could be called with garbage.
use kzalloc() to make sure this wont happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Neal Cardwell <ncardwell@google.com>
This was added by commit 59b9997bab (Revert "net: maintain namespace
isolation between vlan and real device").
In fact, before the initial commit - the one that is reverted -, this
statement was not present.
'skb->dev = dev' is already done in eth_type_trans(), which is call just
after.
Spotted-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An osd client has a red-black tree describing its osds, and
occasionally we would get crashes due to one of these trees tree
becoming corrupt somehow.
The problem turned out to be that reset_changed_osds() was being
called without protection of the osd client request mutex. That
function would call __reset_osd() for any osd that had changed, and
__reset_osd() would call __remove_osd() for any osd with no
outstanding requests, and finally __remove_osd() would remove the
corresponding entry from the red-black tree. Thus, the tree was
getting modified without having any lock protection, and was
vulnerable to problems due to concurrent updates.
This appears to be the only osd tree updating path that has this
problem. It can be fairly easily fixed by moving the call up
a few lines, to just before the request mutex gets dropped
in kick_requests().
This resolves:
http://tracker.ceph.com/issues/5043
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
We send direct probe to broadcast address, as some APs do not respond to
unicast PROBE frames when unassociated. Broadcast frames are not acked,
so we can not use that for trigger MLME state machine, but we need to
use old timeout mechanism.
This fixes authentication timed out like below:
[ 1024.671974] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 1024.694125] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 1024.695450] wlan6: direct probe to 54:e6:fc:98:63:fe (try 2/3)
[ 1024.700586] wlan6: send auth to 54:e6:fc:98:63:fe (try 3/3)
[ 1024.701441] wlan6: authentication with 54:e6:fc:98:63:fe timed out
With fix, we have:
[ 4524.198978] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 4524.220692] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 4524.421784] wlan6: send auth to 54:e6:fc:98:63:fe (try 2/3)
[ 4524.423272] wlan6: authenticated
[ 4524.423811] wlan6: associate with 54:e6:fc:98:63:fe (try 1/3)
[ 4524.427492] wlan6: RX AssocResp from 54:e6:fc:98:63:fe (capab=0x431 status=0 aid=1)
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rcu_barrier() only waits for the currently scheduled rcu functions
to finish - it won't wait for any function scheduled via another
call_rcu() within an rcu scheduled function.
Unfortunately our batadv_tt_orig_list_entry_free_ref() does just that,
via a batadv_orig_node_free_ref() call, leading to our rcu_barrier()
call potentially missing such a batadv_orig_node_free_ref().
This patch fixes this issue by calling the batadv_orig_node_free_rcu()
directly from the rcu callback, removing the unnecessary, additional
call_rcu() layer here.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
tcp_fixup_rcvbuf() contains a loop to estimate initial socket
rcv space needed for a given mss. With large MTU (like 64K on lo),
we can loop ~500 times and consume a lot of cpu cycles.
perf top of 200 concurrent netperf -t TCP_CRR
5.62% netperf [kernel.kallsyms] [k] tcp_init_buffer_space
1.71% netperf [kernel.kallsyms] [k] _raw_spin_lock
1.55% netperf [kernel.kallsyms] [k] kmem_cache_free
1.51% netperf [kernel.kallsyms] [k] tcp_transmit_skb
1.50% netperf [kernel.kallsyms] [k] tcp_ack
Lets use a 100% factor, and remove the loop.
100% is needed anyway for tcp_adv_win_scale=1
default value, and is also the maximum factor.
Refs: commit b49960a05e
("tcp: change tcp_adv_win_scale and tcp_rmem[2]")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO TCP handler has following issues :
1) ooo_okay from original GSO packet is duplicated to all segments
2) segments (but the last one) are orphaned, so transmit path can not
get transmit queue number from the socket. This happens if GSO
segmentation is done before stacked device for example.
Result is we can send packets from a given TCP flow to different TX
queues (if using multiqueue NICS). This generates OOO problems and
spurious SACK & retransmits.
Fix this by keeping socket pointer set for all segments.
This means that every segment must also have a destructor, and the
original gso skb truesize must be split on all segments, to keep
precise sk->sk_wmem_alloc accounting.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains three Netfilter fixes and update
for the MAINTAINER file for your net tree, they are:
* Fix crash if nf_log_packet is called from conntrack, in that case
both interfaces are NULL, from Hans Schillstrom. This bug introduced
with the logging netns support in the previous merge window.
* Fix compilation of nf_log and nf_queue without CONFIG_PROC_FS,
from myself. This bug was introduced in the previous merge window
with the new netns support for the netfilter logging infrastructure.
* Fix possible crash in xt_TCPOPTSTRIP due to missing sanity
checkings to validate that the TCP header is well-formed, from
myself. I can find this bug in 2.6.25, probably it's been there
since the beginning. I'll pass this to -stable.
* Update MAINTAINER file to point to new nf trees at git.kernel.org,
remove Harald and use M: instead of P: (now obsolete tag) to
keep Jozsef in the list of people.
Please, consider pulling this. Thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, the DTIM period is available after a beacon has
been received, and if no beacon has been received enabling
powersave is problematic anyway for synchronisation. Since
some drivers may require the DTIM period for powersave,
don't enable powersave until it becomes available in case
the scan/association managed to not receive a beacon.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the mesh_auth_id was disabled. Instead set the
correct mesh authentication bit based on the mesh setup.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no real difference between *array and array, but
the former confuses smatch so write it differently. The
generated code is exactly the same.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 and the Intel drivers all define crypto
constants, move them to ieee80211.h instead.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an HT AP is advertising channel switch in a beacon, it
doesn't (and shouldn't, according to 802.11-2012 Table 8-20)
include a secondary channel offset element. The only possible
interpretation is that the previous secondary channel offset
remains valid, so use that when switching channel based only
on beacon information.
VHT requires the Wide Bandwidth Channel Switch subelement to
be present in the Channel Switch Wrapper element, so the code
for that is probably ok (see 802.11ac Draft 4, 8.4.2.165.)
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.
This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add regulatory class for 60GHz band, according
to the last specification.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code sending the current WoWLAN TCP wakeup settings in
nl80211_send_wowlan_tcp() is not closing the nested attribute,
thus causing the parser to get confused on the receiver side
in userspace (iw). Fix this.
Cc: stable@vger.kernel.org [3.9]
Reported-by: Deepak Arora <deepakx.arora@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the frame isn't transmitted to the AP, we need to
report it to cfg80211 so the state there can be updated
correctly.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the interface goes down, there's no need to call
cfg80211_mlme_down() after __cfg80211_disconnect() as
the latter will call the former (if appropriate.)
Also, in __cfg80211_disconnect(), if the cfg80211 SME
isn't used, __cfg80211_disconnected() may still need
to be called (depending on the current state) so that
the SME state gets cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, ignore frames with mis-matched BSSID that aren't
multicast or sent to the correct destination. This fixes
reporting public action frames to userspace multiple times
on multiple virtual AP interfaces.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding the attributes fixes an issue with P2P Device not
working properly for management frame TX.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_get_tkip_p2k() may be called with interrupts
disabled, so spin_unlock_bh() isn't safe and leads to
warnings. Since it's always called with BHs disabled
already, just use spin_lock().
Cc: stable@vger.kernel.org
Reported-by: Milan Kocian <milon@wq.cz>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Document rx vs tx status concurrency requirements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an HT AP is advertising channel switch in a beacon, it
doesn't (and shouldn't, according to 802.11-2012 Table 8-20)
include a secondary channel offset element. The only possible
interpretation is that the previous secondary channel offset
remains valid, so use that when switching channel based only
on beacon information.
VHT requires the Wide Bandwidth Channel Switch subelement to
be present in the Channel Switch Wrapper element, so the code
for that is probably ok (see 802.11ac Draft 4, 8.4.2.165.)
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 12e7f51702,
IEEE80211_SDATA_DISCONNECT_RESUME no longer worked as
it would simply never be tested. Restore a bit of the
code removed there and in 9b7d72c104
to make it work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device reports a non-wireless wakeup reason, the
tracing code crashes trying to dereference a NULL pointer.
Fix this by checking the pointer on all accesses and also
add a non_wireless tag to the event.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If rfkill_register() fails in wiphy_register() the struct device
is unregistered but everything else isn't (regulatory, debugfs)
and we even leave the wiphy instance on all internal lists even
though it will likely be freed soon, which is clearly a problem.
Fix this by cleaning up properly.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This target assumes that tcph->doff is well-formed, that may be well
not the case. Add extra sanity checkings to avoid possible crash due
to read/write out of the real packet boundary. After this patch, the
default action on malformed TCP packets is to drop them. Moreover,
fragments are skipped.
Reported-by: Rafal Kupka <rkupka@telemetry.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This seems to have been overlooked when we did the namespace
conversion. If a container is running a legacy version of rpc.gssd
then it will be disrupted if the global 'pipe_version' is set by a
container running the new version of rpc.gssd.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Recent changes to the NFS security flavour negotiation mean that
we have a stronger dependency on rpc.gssd. If the latter is not
running, because the user failed to start it, then we time out
and mark the container as not having an instance. We then
use that information to time out faster the next time.
If, on the other hand, the rpc.gssd successfully binds to an rpc_pipe,
then we mark the container as having an rpc.gssd instance.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull Ceph fixes from Sage Weil:
"Yes, this is a much larger pull than I would like after -rc1. There
are a few things included:
- a few fixes for leaks and incorrect assertions
- a few patches fixing behavior when mapped images are resized
- handling for cloned/layered images that are flattened out from
underneath the client
The last bit was non-trivial, and there is some code movement and
associated cleanup mixed in. This was ready and was meant to go in
last week but I missed the boat on Friday. My only excuse is that I
was waiting for an all clear from the testing and there were many
other shiny things to distract me.
Strictly speaking, handling the flatten case isn't a regression and
could wait, so if you like we can try to pull the series apart, but
Alex and I would much prefer to have it all in as it is a case real
users will hit with 3.10."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (33 commits)
rbd: re-submit flattened write request (part 2)
rbd: re-submit write request for flattened clone
rbd: re-submit read request for flattened clone
rbd: detect when clone image is flattened
rbd: reference count parent requests
rbd: define parent image request routines
rbd: define rbd_dev_unparent()
rbd: don't release write request until necessary
rbd: get parent info on refresh
rbd: ignore zero-overlap parent
rbd: support reading parent page data for writes
rbd: fix parent request size assumption
libceph: init sent and completed when starting
rbd: kill rbd_img_request_get()
rbd: only set up watch for mapped images
rbd: set mapping read-only flag in rbd_add()
rbd: support reading parent page data
rbd: fix an incorrect assertion condition
rbd: define rbd_dev_v2_header_info()
rbd: get rid of trivial v1 header wrappers
...
If wait_event_interruptible_timeout() is successful, it returns
the number of seconds remaining until the timeout. In that
case, we should be retrying the upcall.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
XPRT_BOUND is set on server backchannel xprts by xs_setup_bc_tcp()
(using xprt_set_bound()), and is never cleared, so ->rpcbind() will
never need to be called.
Reported-by: "Myklebust, Trond" <Trond.Myklebust@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Since (69b34fb netfilter: xt_LOG: add net namespace support
for xt_LOG), we hit this:
[ 4224.708977] BUG: unable to handle kernel NULL pointer dereference at 0000000000000388
[ 4224.709074] IP: [<ffffffff8147f699>] ipt_log_packet+0x29/0x270
when callling log functions from conntrack both in and out
are NULL i.e. the net pointer is invalid.
Adding struct net *net in call to nf_logfn() will secure that
there always is a vaild net ptr.
Reported as netfilter's bugzilla bug 818:
https://bugzilla.netfilter.org/show_bug.cgi?id=818
Reported-by: Ronald <ronald645@gmail.com>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
TCP md5 communications fail [1] for some devices, because sg/crypto code
assume page offsets are below PAGE_SIZE.
This was discovered using mlx4 driver [2], but I suspect loopback
might trigger the same bug now we use order-3 pages in tcp_sendmsg()
[1] Failure is giving following messages.
huh, entered softirq 3 NET_RX ffffffff806ad230 preempt_count 00000100,
exited with 00000101?
[2] mlx4 driver uses order-2 pages to allocate RX frags
Reported-by: Matt Schnall <mischnal@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Bernhard Beck <bbeck@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several small bug fixes all over:
1) be2net driver uses wrong payload length when submitting MAC list
get requests to the chip. From Sathya Perla.
2) Fix mwifiex memory leak on driver unload, from Amitkumar Karwar.
3) Prevent random memory access in batman-adv, from Marek Lindner.
4) batman-adv doesn't check for pskb_trim_rcsum() errors, also from
Marek Lindner.
5) Fix fec crashes on rapid link up/down, from Frank Li.
6) Fix inner protocol grovelling in GSO, from Pravin B Shelar.
7) Link event validation fix in qlcnic from Rajesh Borundia.
8) Not all FEC chips can support checksum offload, fix from Shawn
Guo.
9) EXPORT_SYMBOL + inline doesn't make any sense, from Denis Efremov.
10) Fix race in passthru mode during device removal in macvlan, from
Jiri Pirko.
11) Fix RCU hash table lookup socket state race in ipv6, leading to
NULL pointer derefs, from Eric Dumazet.
12) Add several missing HAS_DMA kconfig dependencies, from Geert
Uyttterhoeven.
13) Fix bogus PCI resource management in 3c59x driver, from Sergei
Shtylyov.
14) Fix info leak in ipv6 GRE tunnel driver, from Amerigo Wang.
15) Fix device leak in ipv6 IPSEC policy layer, from Cong Wang.
16) DMA mapping leak fix in qlge from Thadeu Lima de Souza Cascardo.
17) Missing iounmap on probe failure in bna driver, from Wei Yongjun."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
bna: add missing iounmap() on error in bnad_init()
qlge: fix dma map leak when the last chunk is not allocated
xfrm6: release dev before returning error
ipv6,gre: do not leak info to user-space
virtio_net: use default napi weight by default
emac: Fix EMAC soft reset on 460EX/GT
3c59x: fix PCI resource management
caif: CAIF_VIRTIO should depend on HAS_DMA
net/ethernet: MACB should depend on HAS_DMA
net/ethernet: ARM_AT91_ETHER should depend on HAS_DMA
net/wireless: ATH9K should depend on HAS_DMA
net/ethernet: STMMAC_ETH should depend on HAS_DMA
net/ethernet: NET_CALXEDA_XGMAC should depend on HAS_DMA
ipv6: do not clear pinet6 field
macvlan: fix passthru mode race between dev removal and rx path
ipv4: ip_output: remove inline marking of EXPORT_SYMBOL functions
net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode
net/mlx4_core: Add missing report on VST and spoof-checking dev caps
net: fec: enable hardware checksum only on imx6q-fec
qlcnic: Fix validation of link event command.
...
The rbd code has a need to be able to restart an osd request that
has already been started and completed once before. This currently
wouldn't work right because the osd client code assumes an osd
request will be started exactly once Certain fields in a request
are never cleared and this leads to trouble if you try to reuse it.
Specifically, the r_sent, r_got_reply, and r_completed fields are
never cleared. The r_sent field records the osd incarnation at the
time the request was sent to that osd. If that's non-zero, the
message won't get re-mapped to a target osd properly, and won't be
put on the unsafe requests list the first time it's sent as it
should. The r_got_reply field is used in handle_reply() to ensure
the reply to a request is processed only once. And the r_completed
field is used for lingering requests to avoid calling the callback
function every time the osd client re-sends the request on behalf of
its initiator.
Each osd request passes through ceph_osdc_start_request() when
responsibility for the request is handed over to the osd client for
completion. We can safely zero these three fields there each time a
request gets started.
One last related change--clear the r_linger flag when a request
is no longer registered as a linger request.
This resolves:
http://tracker.ceph.com/issues/5026
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This should return zero on success and -EBUSY on error so the type
needs to be int instead of bool.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Avoid waking up every thread sleeping in read call on an AF_UNIX
socket during suspend and resume by calling a freezable blocking
call. Previous patches modified the freezer to avoid sending
wakeups to threads that are blocked in freezable blocking calls.
This call was selected to be converted to a freezable call because
it doesn't hold any locks or release any resources when interrupted
that might be needed by another freezing task or a kernel driver
during suspend, and is a common site where idle userspace tasks are
blocked.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NFS calls the freezable helpers with locks held, which is unsafe
and will cause lockdep warnings when 6aa9707 "lockdep: check
that no locks held at freeze time" is reapplied (it was reverted
in dbf520a). NFS shouldn't be doing this, but it has
long-running syscalls that must hold a lock but also shouldn't
block suspend. Until NFS freeze handling is rewritten to use a
signal to exit out of the critical section, add new *_unsafe
versions of the helpers that will not run the lockdep test when
6aa9707 is reapplied, and call them from NFS.
In practice the likley result of holding the lock while freezing
is that a second task blocked on the lock will never freeze,
aborting suspend, but it is possible to manufacture a case using
the cgroup freezer, the lock, and the suspend freezer to create
a deadlock. Silencing the lockdep warning here will allow
problems to be found in other drivers that may have a more
serious deadlock risk, and prevent new problems from being added.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We forget to call dev_put() on error path in xfrm6_fill_dst(),
its caller doesn't handle this.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a hole in struct ip6_tnl_parm2, so we have to
zero the struct on stack before copying it to user-space.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have seen multiple NULL dereferences in __inet6_lookup_established()
After analysis, I found that inet6_sk() could be NULL while the
check for sk_family == AF_INET6 was true.
Bug was added in linux-2.6.29 when RCU lookups were introduced in UDP
and TCP stacks.
Once an IPv6 socket, using SLAB_DESTROY_BY_RCU is inserted in a hash
table, we no longer can clear pinet6 field.
This patch extends logic used in commit fcbdf09d96
("net: fix nulls list corruptions in sk_prot_alloc")
TCP/UDP/UDPLite IPv6 protocols provide their own .clear_sk() method
to make sure we do not clear pinet6 field.
At socket clone phase, we do not really care, as cloning the parent (non
NULL) pinet6 is not adding a fatal race.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix parsing of user typed protocol string to avoid random memory access in
some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=n0yL
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- fix parsing of user typed protocol string to avoid random memory access in
some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
Signed-off-by: David S. Miller <davem@davemloft.net>
EXPORT_SYMBOL and inline directives are contradictory to each other.
The patch fixes this inconsistency.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
Pull nfsd fixes from Bruce Fields:
"Small fixes for two bugs and two warnings"
* 'for-3.10' of git://linux-nfs.org/~bfields/linux:
nfsd: fix oops when legacy_recdir_name_error is passed a -ENOENT error
SUNRPC: fix decoding of optional gss-proxy xdr fields
SUNRPC: Refactor gssx_dec_option_array() to kill uninitialized warning
nfsd4: don't allow owner override on 4.1 CLAIM_FH opens
- Ensure that we match the 'sec=' mount flavour against the server list
- Fix the NFSv4 byte range locking in the presence of delegations
- Ensure that we conform to the NFSv4.1 spec w.r.t. freeing lock stateids
- Fix a pNFS data server connection race
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=5zpc
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client bugfixes from Trond Myklebust:
- Ensure that we match the 'sec=' mount flavour against the server list
- Fix the NFSv4 byte range locking in the presence of delegations
- Ensure that we conform to the NFSv4.1 spec w.r.t. freeing lock
stateids
- Fix a pNFS data server connection race
* tag 'nfs-for-3.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4.1 Fix data server connection race
NFSv3: match sec= flavor against server list
NFSv4.1: Ensure that we free the lock stateid on the server
NFSv4: Convert nfs41_free_stateid to use an asynchronous RPC call
SUNRPC: Don't spam syslog with "Pseudoflavor not found" messages
NFSv4.x: Fix handling of partially delegated locks
nc_worker accesses the originator table during its periodic
work, but since the originator table is freed before
stopping the worker this leads to a global protection fault.
Fix this by killing the worker (in nc_free) before freeing
the originator table.
Moreover tidy up the entire clean up routine by running all
the subcomponents freeing procedures first and then killing
the TT and the originator tables at the end.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
In the outgoing ARP request snooping routine in DAT, ARP
Request sent by local clients which are supposed to be
replied by other local clients can be silently dropped.
The destination host will reply by itself through the LAN
and therefore there is no need to involve DAT.
Reported-by: Carlos Quijano <carlos@crqgestion.es>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Tested-by: Carlos Quijano <carlos@crqgestion.es>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batadv_param_set_ra() strips the trailing '\n' from the supplied
string buffer without checking the length of the buffer first. This
patches avoids random memory access and associated potential
crashes.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
