Properly test for controller interface to see if it's DMA capable. As many
controllers are misconfigured in this regard, also add debug parameters to
force DMA support either way.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification states that the capabilities register might need a reset to
get correct values after boot up.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check the interface version of the controller and bail out if it's an unknown
version.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conform to the sdhci specification as to which inhibit bits should be checked
at different times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The controller has an upper limit on the block size. Make sure we do not
cross it.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers will issue an interrupt when a configurable number of
bytes have been transfered using DMA. The purpose is to handle multiple,
scattered memory pages.
Unfortunately, it requires that all transfers are completely aligned to
memory pages, which we cannot guarantee. So we just disable the function.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers operate with blocks, not bytes. The PIO routines must
therefore make sure that the minimum unit transfered is a complete block.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The specification says that interrupts should be cleared before the source is
removed. We should also not set unknown bits.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci specification states that some registers must be written to in a
specific order.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the give timeout clock and calculate a proper timeout instead of using the
maximum at all times.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The reset register is automatically cleared when the reset has completed.
Hence, we should busy wait and not have a fixed delay.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current timeout loop assume that jiffies are updated. This might not be
the case depending on locks and if the kernel is compiled without preemption.
Change the system to use a counter and fixed delays.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sdhci controllers can support up to three voltage levels. Detect which
and report back to the MMC layer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As sdhci is a generic driver, it is helpful to see some more specific
identification of the actual hardware in dmesg. PCI vendor, device and
revision is sufficient in most cases.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A base clock value of 0 means that the driver must get the base clock through
some other means. As we have no other way of getting it, we must abort.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 64 bits resource patches did a bit of damage on PowerMac causing a
buffer overflow in macio_asic and a warning in a sound driver. The
former is fixed by reverting the sprintf of the bus_id to %08x as it was
before. The bus_id used for macio devices is always a 32 bits value
(macio always sits in 32 bits space) and since it's exposed to userland,
the format of the string shouldn't be changed like that anyway. The
second by using the proper type for printk.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Include the generic header file instead of the ARM specific one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Include the generic header file instead of the ARM specific one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most batteries today are ACPI "Control Method" batteries,
but some models ship with the older "Smart Battery"
that requires this code.
Rich Townsend and Bruno Ducrot were the original authors.
Vladimir Lebedev updated to run on latest kernel.
http://bugzilla.kernel.org/show_bug.cgi?id=3734
Signed-off-by: Len Brown <len.brown@intel.com>
This patch switches back the display nodes for M6R and M6N -- this happened
a while ago when a patch was misapplied (only the in-tree version was
affected).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Patch from Tony Lindgren
This patch makes OMAP MMC work again:
- Fix compile errors
- Do not ioremap base as it is already statically mapped
- Clean-up platform device handling
- Fix compile warnings
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suppress the "setup_irq: irq handler mismatch" coming out of pnp_check_irq():
failures are expected here.
Cc: <stable@kernel.org>
Cc: Santiago Garcia Mantinan <manty@manty.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Network Block Device driver doesn't compile if NDEBUG is defined.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing variable initialisation would mean it would sometimes not put ATAPI
devices into DMA by default.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: <Jack.Lee@ite.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a renamed and tested version of the previous S3C24XX RTC class
driver.
The driver has been renamed from the original s3c2410-rtc, which is now too
narrow for the range of devices supported.
The rtc-s3c has been chosen as there is the distinct possibility of this
driver being carried forward into newer Samsung SoC silicon.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove ips namespace from infinipath drivers. This renames ips_common.h to
ipath_common.h. Definitions, data structures, etc. that were not used by
kernel modules have moved to user-only headers. All names including ips have
been renamed to ipath. Some names have had an ipath prefix added.
Signed-off-by: Christian Bell <christian.bell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The receive work queue size should be ignored if the QP is created to use a
shared receive queue according to the IB spec.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't tell for sure if any packets are in the infinipath receive buffer
when we shut down a chip port. Normally this is taken care of by orderly
shutdown, but when processes are terminated, or sending process has a bug, we
can continue to receive packets. So rather than writing zero to the address
registers for the closing port, we point it at a dummy memory.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We must increment uaddr by size we are reading or writing, since it's passed
as a char *, not a pointer to the appropriate size.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do a few more explicit checks for specific models, and now also support the
old PathScale serial number style, or new QLogic style.
This is backwards compatible with previous versions of software and hardware.
That is, older software will see a plausible serial number and correct GUID
when used with a new board, while newer software will correctly handle an
older board.
Signed-off-by: Mike Albaugh <mike.albaugh@qlogic.com>
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This attribute group made it into the original driver, but should not have.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The two arrays only had space for 4 units.
Also changed from ipath_set_sps_lid() to ipath_set_lid(); the sps was
leftover.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch separates QP state used for sending and receiving RC packets so the
processing in the receive interrupt handler can be done mostly without locks
being held. ACK packets are now sent without requiring synchronization with
the send tasklet.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes some problems uncovered during IB compliance testing to
return the right values for error counters returned by the Performance Get
Counters packet.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The tail register read became redundant as the result of earlier receive
interrupt bug fixes.
Drop another unneeded register read.
And another line that got duplicated.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do an extra check to see if in-memory tail changed while processing packets,
and if so, going back through the loop again (but only once per call to
ipath_kreceive()). In practice, this seems to be enough to guarantee that if
we crossed the clearing of an interrupt at start of ipath_intr with a
scheduled tail register update, that we'll process the "extra" packet that
lost the interrupt because we cleared it just as it was about to arrive.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The problem was that I was updating the head register multiple times in the
rcvhdrq processing loop, and setting the counter on each update. Since that
meant that the tail register was ahead of head for all but the last update, we
would get extra interrupts. The fix was to not write the counter value except
on the last update.
I also changed to update rcvhdrhead and rcvegrindexhead at most every 16
packets, if there were lots of packets in the queue (and of course, on the
last packet, regardless).
I also made some small cleanups while debugging this.
With these changes, xeon/monty typically sees two openib packets per interrupt
on sdp and ipoib, opteron/monty is about 1.25 pkts/intr.
I'm seeing about 3800 Mbit/s monty/xeon, and 5000-5100 opteron/monty with
netperf sdp. Netpipe doesn't show as good as that, peaking at about 4400 on
opteron/monty sdp. Plain ipoib xeon is about 2100+ netperf, opteron 2900+, at
128KB
Signed-off-by: olson@eng-12.pathscale.com
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also count the number of interrupts where that works (fastrcvint). On any
interrupt where the port0 head and tail registers are not equal, just call the
ipath_kreceive code without reading the interrupt status, thus saving the
approximately 0.25usec processor stall waiting for the read to return. If any
other interrupt bits are set, or head==tail, take the normal path, but that
has been reordered to handle read ahead of pioavail. Also no longer call
ipath_kreceive() from ipath_qcheck(), because that just seems to make things
worse, and isn't really buying us anything, these days.
Also no longer loop in ipath_kreceive(); better to not hold things off too
long (I saw many cases where we would loop 4-8 times, and handle thousands (up
to 3500) in a single call).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Made in-memory rcvhdrq tail update be in dma_alloc'ed memory, not random user
or special kernel (needed for ppc, also "just the right thing to do").
Some cleanups to make unexpected link transitions less likely to produce
complaints about packet errors, and also to not leave SMA packets stuck and
unable to go out.
A few other random debug and comment cleanups.
Always init rcvhdrq head/tail registers to 0, to avoid race conditions (should
have been that way some time ago).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is not a DMA target, so no need to use dma_alloc_coherent on it.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This helps us to survive better when memory is fragmented.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These limits are somewhat artificial in that we don't actually have any
device limits. However, the verbs layer expects that such limits exist
and are enforced, so we make up arbitrary (but sensible) limits.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is no longer a /dev/ipath_diag file; instead, there's
/dev/ipath_diag0, 1, etc.
It's still not possible to have diags run on more than one unit at a time,
but that's easy to fix at some point.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the quoted module name in the sysfs for EDAC modules and reported by several
people.
Instead of ../_edac_e752x_/ now the following will be presented, like other
modules: ../edac_e752x/
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix section mismatch warnings:
WARNING: drivers/scsi/qla1280.o - Section mismatch: reference to
.init.data: from .text between 'qla1280_get_token' (at offset 0x2a16)
and 'qla1280_probe_one'
WARNING: drivers/scsi/qla1280.o - Section mismatch: reference to
.init.data: from .text between 'qla1280_get_token' (at offset 0x2a3c)
and 'qla1280_probe_one'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the current problems the mptsas driver has is that of "ghost"
devices (these are devices the firmware reports as existing, but what
they actually represent are the parents of a lower device), so for
example in my dual expander configuration, three expanders actually show
up, two for the real expanders but a third is created because the
firmware reports that the lower expander also has another expander
connected (which is simply the port going back to the upper expander).
The attached patch eliminates all these ghosts by not allocating any
devices for them if the SAS address is the SAS address of the parent.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a few spaces to MODULE_PARM_DESC() text for qla2xxx. Without these
spaces text runs together when modinfo prints the text.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The way mpt_interrupt() was coded, it was impossible for the unhandled
interrupt detection logic to ever trigger. All interrupt handlers should
return IRQ_NONE when they have nothing to do.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I got a NULL derefrence in cdev_del+1 when called from sg_remove. By looking at
the code of sg_add, sg_alloc and sg_remove (all in drivers/scsi/sg.c) I found
out that sg_add is calling sg_alloc but if it fails afterwards it does not
deallocate the space that was allocated in sg_alloc and the redundant entry has
NULL in cdev. When sg_remove is being called, it tries to perform cdev_del to
this NULL cdev and fails.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch switches back the display nodes for M6R and M6N -- this happened
a while ago when a patch was misapplied (only the in-tree version was
affected).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This small patch adds back WLED control for S1N models, this was
accidentally removed a while ago.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch reworks laptop model detection.
This addresses the Samsung P30 issue, where the INIT method would return no
object, but the implicit return in the AML interpreter would confuse the
driver. It also accounts for a newer batch of Asus models whose INIT
returns ACPI_TYPE_BUFFER instead of STRING.
The handling is now much leaner, if we get a buffer or a string, we check
against known values, in every other case we use a different path
(currently DSDT signatures). The bulk of this patch is separating the
string matching from asus_hotk_get_info() into a separate function.
This patch properly fixes http://bugme.osdl.org/show_bug.cgi?id=5067 and
http://bugme.osdl.org/show_bug.cgi?id=5092 and makes the driver fully
functional again with acpi=strict on all machines.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for Asus L5D and thus fixes
http://bugme.osdl.org/show_bug.cgi?id=4695
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch creates a new file named "bluetooth" under /proc/acpi/asus/.
This file controls both the internal Bluetooth adapter's presence on the
USB bus and the associated LED.
echo 1 > /proc/acpi/asus/bluetooth to enable, 0 to disable.
Additionally, the patch add support for Asus W5A, the first model that uses
this feature.
Patch originally by Fernando A. P. Gomes.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for Asus A4G.
Originally by Giuseppe Rota.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds handling for front LED displays found on W1N and the like.
Additionally, W1N is given its own model_data instance.
Patch originally by Éric Burghard.
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch updates the version string, copyright notices and does
whitespace cleanup (it looks weird, blame Lindent).
Signed-off-by: Karol Kozimor <sziwan@hell.org.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Kill sun4v virtual device layer.
[SERIAL] sunhv: Convert to of_driver layer.
[SPARC64]: Mask out top 8-bits in physical address when building resources.
[SERIAL] sunsu: Missing return statement in su_probe().
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV6]: Added GSO support for TCPv6
[NET]: Generalise TSO-specific bits from skb_setup_caps
[IPV6]: Added GSO support for TCPv6
[IPV6]: Remove redundant length check on input
[NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks
[TG3]: Update version and reldate
[TG3]: Add TSO workaround using GSO
[TG3]: Turn on hw fix for ASF problems
[TG3]: Add rx BD workaround
[TG3]: Add tg3_netif_stop() in vlan functions
[TCP]: Reset gso_segs if packet is dodgy
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Set alternate port number when initializing QP attributes
IB/uverbs: Set correct user handle for user SRQs
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6/:
[PATCH] pcmcia: fix deadlock in pcmcia_parse_events
[PATCH] com20020_cs: more device support
[PATCH] au1xxx: pcmcia: fix __init called from non-init
[PATCH] kill open-coded offsetof in cm4000_cs.c ZERO_DEV()
[PATCH] pcmcia: convert pcmcia_cs to kthread
[PATCH] pcmcia: fix kernel-doc function name
[PATCH] pcmcia: hostap_cs.c - 0xc00f,0x0000 conflicts with pcnet_cs
[PATCH] pcmcia: at91_cf suspend/resume/wakeup
[PATCH] pcmcia: Make ide_cs work with the memory space of CF-Cards if IO space is not available
[PATCH] pcmcia: TI PCIxx12 CardBus controller support
[PATCH] pcmcia: warn if driver requests exclusive, but gets a shared IRQ
[PATCH] pcmcia: expose tool in pcmcia/Documentation/pcmcia/
[PATCH] pcmcia: another ID for serial_cs.c
[PATCH] yenta: fix hidden PCI bus numbers
[PATCH] yenta: do power-up only after socket is configured
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4290): Add support for the TCL M2523_3DB_E tuner.
V4L/DVB (4289): Missing statement in drivers/media/dvb/frontends/cx22700.c
V4L/DVB (4288): Clean out a zillion sparse warnings in pvrusb2
V4L/DVB (4287): Pvrusb2/: possible cleanups
V4L/DVB (4285): Cx88: add support for Geniatech Digistar / Digiwave 103g
V4L/DVB (4284): Cx24123: fix set_voltage function according to the specs
V4L/DVB (4282): Fix: use swzigzag for swalgo
V4L/DVB (4281): TDA9887_SET_CONFIG should only be handled by the tda9887.
V4L/DVB (4277): Fix CI interface on PRO KNC1 cards
V4L/DVB (4276): Fix CI on old KNC1 DVBC cards
V4L/DVB (4275): The FE_SET_FRONTEND_TUNE_MODE ioctl always returns EOPNOTSUPP
V4L/DVB (4274): Eliminate use of tda9887 from pvrusb2 driver
V4L/DVB (4273): Always log pvrusb2 device register / unregister events
V4L/DVB (4272): Fix tveeprom supported standards
V4L/DVB (4270): Add tda9887-specific tuner configuration
V4L/DVB (4269): Subject: videocodec: make 1-bit fields unsigned
V4L/DVB (4267): Remove all instances of request_module("tda9887")
V4L/DVB (4264): Cx88-blackbird: implement VIDIOC_QUERYCTRL and VIDIOC_QUERYMENU
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (25 commits)
ACPI: Kconfig: ACPI_SRAT depends on ACPI
ACPI: drivers/acpi/scan.c: make acpi_bus_type static
ACPI: fixup memhotplug debug message
ACPI: ACPICA 20060623
ACPI: C-States: only demote on current bus mastering activity
ACPI: C-States: bm_activity improvements
ACPI: C-States: accounting of sleep states
ACPI: additional blacklist entry for ThinkPad R40e
ACPI: restore comment justifying 'extra' P_LVLx access
ACPI: fix battery on HP NX6125
ACPIPHP: prevent duplicate slot numbers when no _SUN
ACPI: static-ize handle_hotplug_event_func()
ACPIPHP: use ACPI dock driver
ACPI: dock driver
KEVENT: add new uevent for dock
ACPI: asus_acpi_init: propagate correct return value
[ACPI] Print error message if remove/install notify handler fails
ACPI: delete tracing macros from drivers/acpi/*.c
ACPI: HW P-state coordination support
ACPI: un-export ACPI_ERROR() -- use printk(KERN_ERR...)
...
This patch adds GSO support for IPv6 and TCPv6. This is based on a patch
by Ananda Raju <Ananda.Raju@neterion.com>. His original description is:
This patch enables TSO over IPv6. Currently Linux network stacks
restricts TSO over IPv6 by clearing of the NETIF_F_TSO bit from
"dev->features". This patch will remove this restriction.
This patch will introduce a new flag NETIF_F_TSO6 which will be used
to check whether device supports TSO over IPv6. If device support TSO
over IPv6 then we don't clear of NETIF_F_TSO and which will make the
TCP layer to create TSO packets. Any device supporting TSO over IPv6
will set NETIF_F_TSO6 flag in "dev->features" along with NETIF_F_TSO.
In case when user disables TSO using ethtool, NETIF_F_TSO will get
cleared from "dev->features". So even if we have NETIF_F_TSO6 we don't
get TSO packets created by TCP layer.
SKB_GSO_TCPV4 renamed to SKB_GSO_TCP to make it generic GSO packet.
SKB_GSO_UDPV4 renamed to SKB_GSO_UDP as UFO is not a IPv4 feature.
UFO is supported over IPv6 also
The following table shows there is significant improvement in
throughput with normal frames and CPU usage for both normal and jumbo.
--------------------------------------------------
| | 1500 | 9600 |
| ------------------|-------------------|
| | thru CPU | thru CPU |
--------------------------------------------------
| TSO OFF | 2.00 5.5% id | 5.66 20.0% id |
--------------------------------------------------
| TSO ON | 2.63 78.0 id | 5.67 39.0% id |
--------------------------------------------------
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GSO to workaround a rare TSO bug on some chips. This hardware
bug may be triggered when the TSO header size is greater than 80
bytes. When this condition is detected in a TSO packet, the driver
will use GSO to segment the packet to workaround the hardware bug.
Thanks to Juergen Kreileder <jk@blackdown.de> for reporting the
problem and collecting traces to help debug the problem.
And thanks to Herbert Xu <herbert@gondor.apana.org.au> for providing
the GSO mechanism that happens to be the perfect workaround for this
problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear a bit to enable a hardware fix for some ASF related problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround to limit the burst size of rx BDs being DMA'ed to the
chip. This works around hardware errata on a number of 5750, 5752,
and 5755 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_netif_stop() when changing the vlgrp (vlan group) pointer. It
is necessary to quiesce the device before changing that pointer.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set alternate port number when initializing QP attributes. This bug
is OpenFabrics bugzilla bug #160.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Store away the user handle passed in from userspace when creating an
SRQ, so that the kernel can return the correct handle when an SRQ
asynchronous event occurs. (A 0 was incorrectly stored as the user
handle as part of the changes in 9ead190b, "IB/uverbs: Don't serialize
with ib_uverbs_idr_mutex")
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PCMCIA layer calls pcmcia_parse_events both from user context and
IRQ context; the lock thus needs to be irqsave to avoid deadlocks
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Enable the com20020_cs arcnet driver to see the SoHard (now Mercury
Computer Systems Inc.) SH ARC-PCMCIA card.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This must not be marked __init, as it is called from
au1x00_drv_pcmcia_probe.
Signed-off-by: Domen Puncer <domen.puncer@ultra.si>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
... to make sure that it doesn't break again when a field changes (see
"[PATCH] pcmcia: fix zeroing of cm4000_cs.c data" for recent example).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert pcmcia_cs to use kthread instead of the deprecated
kernel_thread.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Comment out the ID 0xc00f,0x0000 in hostap_cs.c, as it conflicts with the
pcnet_cs driver.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
AT91 CF updates, mostly for power management:
- Add suspend/resume methods to the AT91 CF driver, disabling
non-wakeup IRQs during system suspend. The card detect IRQ
serves as a wakeup event source.
- Convert the driver to the more-current "platform_driver" style.
So inserting or removing a CF card will wake the system, unless that
has been disabled by updating the sysfs file; and there will be no
more warnings about spurious IRQs during suspend/resume cycles.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch enables ide_cs to access CF-cards via their common memory
rather than via their IO space.
Signed-off-by: Thomas Kleffel <tk@maintech.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below adds support for the TI PCIxx12 CardBus controllers.
This seems to be sufficient to detect the cardbus bridge on an HP nc6320
and works with an orinoco wifi card.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below cleans up the pcmcia code a bit on the IRQ side (I did
this while debugging the problem just so I could read wtf it was doing),
and also adds a warning and passes back the correct information when a
device asks for exclusive but gets given shared. This at least means the
dmesg dump of a problem triggered by this will have a signature to find.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fixup the subordinate number parent bridge of yenta Cardbus Bridges
before the PCI bus scan starts to make the cardbus cards which are
otherwise hidden for PCI scans work.
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Power-up the card only after the socket is configured. power-down in
the old place. The point is not to power-up the card before the interrupt
routing is set up correctly.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Stumbled over this because of coverity (id #492),
seems like we are missing a return statement here and fail
to do proper bounds checking. If this assumption is false
we should at least change the identation to make it clear
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 unused global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the Geniatech Digistar, aka
Digiwave 103g DVB-S card.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The set_voltage function in cx24123.c was corrected to match how it is
described in the CX24123 specs, producing the correct behaviour for cards
that require it.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The original driver had a restriction that if a card as an saa7113 chip,
then it cannot have a CI interface. This is not the case.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These cards do not need the tda10021 configuration change when data is
streamed through a CAM module. This disables it for these ones.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When someone added the front-end ioctl FE_SET_FRONTEND_TUNE_MODE, they
forgot to set the return value to 0. It always returns EOPNOTSUPP,
causing problems for programmers who actually check for error conditions.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously the pvrusb2 driver was conditionalizing printing of the
device register / unregister messages against a debug mask. This sort
of information should always appear, thus this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The supported standards by the tuner on tveeprom were too restricted.
It were showing just the main format, instead of the format family.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Many tda9887 settings depend on the chosen tuner. Expand the tuner parameters
to include these tda9887 settings.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch implements the newer v4l2 control features to make the
standard user controls and mpeg encoder controls of cx88-blackbird
video encoder boards available to userspace.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/i2c/busses/i2c-i801.c: In function 'i801_probe':
drivers/i2c/busses/i2c-i801.c:496: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
Cc: Greg KH <greg@kroah.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add lower-level functions that handle various parts of the initialization
done by the xxx_probe1() functions. Some of the xxx_probe1() functions are
much too long and complicated (see "Chapter 5: Functions" in
Documentation/CodingStyle).
- Cleanup of probe1() functions in EDAC
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove add_mc_to_global_list(). In next patch, this function will be
reimplemented with different semantics.
1 Reimplement add_mc_to_global_list() with semantics that allow the caller to
determine the ID number for a mem_ctl_info structure. Then modify
edac_mc_add_mc() so that the caller specifies the ID number for the new
mem_ctl_info structure. Platform-specific code should be able to assign the
ID numbers in a platform-specific manner. For instance, on Opteron it makes
sense to have the ID of the mem_ctl_info structure match the ID of the node
that the memory controller belongs to.
2 Modify callers of edac_mc_add_mc() so they use the new semantics.
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change MC drivers from using CVS revision strings for their version number,
Now each driver has its own local string.
Remove some PCI dependencies from the core EDAC module. Made the code 'struct
device' centric instead of 'struct pci_dev' Most of the code changes here are
from a patch by Dave Jiang. It may be best to eventually move the
PCI-specific code into a separate source file.
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- make __cm206_init() __init (required since it calls
the __init cm206_init())
- make the needlessly global bcdbin() static
- remove a comment with an obsolete compile command
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't show a menu that can't be entered due to lack of contents on arm (the
options are only available on arm26).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ian Molton <spyro@f2s.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the USB core to save and pass the sending task secid when
sending signals upon AIO completion so that proper security checking can be
applied by security modules.
Signed-off-by: David Quigley <dpquigl@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remaining counters in page_state after the zoned VM counter patches
have been applied are all just for show in /proc/vmstat. They have no
essential function for the VM.
We use a simple increment of per cpu variables. In order to avoid the most
severe races we disable preempt. Preempt does not prevent the race between
an increment and an interrupt handler incrementing the same statistics
counter. However, that race is exceedingly rare, we may only loose one
increment or so and there is no requirement (at least not in kernel) that
the vm event counters have to be accurate.
In the non preempt case this results in a simple increment for each
counter. For many architectures this will be reduced by the compiler to a
single instruction. This single instruction is atomic for i386 and x86_64.
And therefore even the rare race condition in an interrupt is avoided for
both architectures in most cases.
The patchset also adds an off switch for embedded systems that allows a
building of linux kernels without these counters.
The implementation of these counters is through inline code that hopefully
results in only a single instruction increment instruction being emitted
(i386, x86_64) or in the increment being hidden though instruction
concurrency (EPIC architectures such as ia64 can get that done).
Benefits:
- VM event counter operations usually reduce to a single inline instruction
on i386 and x86_64.
- No interrupt disable, only preempt disable for the preempt case.
Preempt disable can also be avoided by moving the counter into a spinlock.
- Handling is similar to zoned VM counters.
- Simple and easily extendable.
- Can be omitted to reduce memory use for embedded use.
References:
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=113512330605497&w=2
RFC http://marc.theaimsgroup.com/?l=linux-kernel&m=114988082814934&w=2
local_t http://marc.theaimsgroup.com/?l=linux-kernel&m=114991748606690&w=2
V2 http://marc.theaimsgroup.com/?t=115014808400007&r=1&w=2
V3 http://marc.theaimsgroup.com/?l=linux-kernel&m=115024767022346&w=2
V4 http://marc.theaimsgroup.com/?l=linux-kernel&m=115047968808926&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The numa statistics are really event counters. But they are per node and
so we have had special treatment for these counters through additional
fields on the pcp structure. We can now use the per zone nature of the
zoned VM counters to realize these.
This will shrink the size of the pcp structure on NUMA systems. We will
have some room to add additional per zone counters that will all still fit
in the same cacheline.
Bits Prior pcp size Size after patch We can add
------------------------------------------------------------------
64 128 bytes (16 words) 80 bytes (10 words) 48
32 76 bytes (19 words) 56 bytes (14 words) 8 (64 byte cacheline)
72 (128 byte)
Remove the special statistics for numa and replace them with zoned vm
counters. This has the side effect that global sums of these events now
show up in /proc/vmstat.
Also take the opportunity to move the zone_statistics() function from
page_alloc.c into vmstat.c.
Discussions:
V2 http://marc.theaimsgroup.com/?t=115048227000002&r=1&w=2
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_bounce to a per zone counter
nr_bounce is only used for proc output. So it could be left as an event
counter. However, the event counters may not be accurate and nr_bounce is
categorizing types of pages in a zone. So we really need this to also be a
per zone counter.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_unstable to a per zone counter
We need to do some special modifications to the nfs code since there are
multiple cases of disposition and we need to have a page ref for proper
accounting.
This converts the last critical page state of the VM and therefore we need to
remove several functions that were depending on GET_PAGE_STATE_LAST in order
to make the kernel compile again. We are only left with event type counters
in page state.
[akpm@osdl.org: bugfixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_writeback to per zone counter.
This removes the last page_state counter from arch/i386/mm/pgtable.c so we
drop the page_state from there.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes nr_dirty a per zone counter. Looping over all processors is
avoided during writeback state determination.
The counter aggregation for nr_dirty had to be undone in the NFS layer since
we summed up the page counts from multiple zones. Someone more familiar with
NFS should probably review what I have done.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conversion of nr_page_table_pages to a per zone counter
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Allows reclaim to access counter without looping over processor counts.
- Allows accurate statistics on how many pages are used in a zone by
the slab. This may become useful to balance slab allocations over
various zones.
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current NR_FILE_MAPPED is used by zone reclaim and the dirty load
calculation as the number of mapped pagecache pages. However, that is not
true. NR_FILE_MAPPED includes the mapped anonymous pages. This patch
separates those and therefore allows an accurate tracking of the anonymous
pages per zone.
It then becomes possible to determine the number of unmapped pages per zone
and we can avoid scanning for unmapped pages if there are none.
Also it may now be possible to determine the mapped/unmapped ratio in
get_dirty_limit. Isnt the number of anonymous pages irrelevant in that
calculation?
Note that this will change the meaning of the number of mapped pages reported
in /proc/vmstat /proc/meminfo and in the per node statistics. This may affect
user space tools that monitor these counters! NR_FILE_MAPPED works like
NR_FILE_DIRTY. It is only valid for pagecache pages.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently a single atomic variable is used to establish the size of the page
cache in the whole machine. The zoned VM counters have the same method of
implementation as the nr_pagecache code but also allow the determination of
the pagecache size per zone.
Remove the special implementation for nr_pagecache and make it a zoned counter
named NR_FILE_PAGES.
Updates of the page cache counters are always performed with interrupts off.
We can therefore use the __ variant here.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
nr_mapped is important because it allows a determination of how many pages of
a zone are not mapped, which would allow a more efficient means of determining
when we need to reclaim memory in a zone.
We take the nr_mapped field out of the page state structure and define a new
per zone counter named NR_FILE_MAPPED (the anonymous pages will be split off
from NR_MAPPED in the next patch).
We replace the use of nr_mapped in various kernel locations. This avoids the
looping over all processors in try_to_free_pages(), writeback, reclaim (swap +
zone reclaim).
[akpm@osdl.org: bugfix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/char/istallion.c: In function âstli_initbrdsâ:
drivers/char/istallion.c:4150: error: implicit declaration of function âstli_parsebrdâ
drivers/char/istallion.c:4150: error: âstli_brdspâ undeclared (first use in this function)
drivers/char/istallion.c:4150: error: (Each undeclared identifier is reported only once
drivers/char/istallion.c:4150: error: for each function it appears in.)
drivers/char/istallion.c:4164: error: implicit declaration of function âstli_argbrdsâ
While I was at it, I also removed the #ifdef MODULE around the initialation
code to allow it to perhaps work when built into the kernel and made a
needlessly global function static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes drivers/char/pc8736x_gpio.c and drivers/char/scx200_gpio.c to
use the platform_device_del/put ops correctly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build error on x86_64. There's nothing even remotely close to
imacmp_seg in the kernel, so I removed the whole line.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo spotted by
Matt LaPlante <webmaster@cyberdogtech.com>.
This patch fixes kernel Bugzilla #6704.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
- Use it instead of acpi_bus_get_device() in acpi_video_bus_notify()
and use the one from struct acpi_video_device in
acpi_video_device_notify().
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Use it instead of acpi_bus_get_device() where we can..
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Use it instead of acpi_bus_get_device() where we can..
Signed-off-by: Patrick Mochel <mochel@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
