This patch is to remove the typedef sctp_state_t, and
replace with enum sctp_state in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_ierror_t, and
replace with enum sctp_ierror in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_xmit_t, and
replace with enum sctp_xmit in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_sock_state_t, and
replace with enum sctp_sock_state in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_transport_cmd_t, and
replace with enum sctp_transport_cmd in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_scope_t, and
replace with enum sctp_scope in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_scope_policy_t and keep
it's members as an anonymous enum.
It is also to define SCTP_SCOPE_POLICY_MAX to replace the num 3
in sysctl.c to make codes clear.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_retransmit_reason_t, and
replace with enum sctp_retransmit_reason in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the typedef sctp_lower_cwnd_t, and
replace with enum sctp_lower_cwnd in the places where it's
using this typedef.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the GMAC on the Anarion chip can be used, the PHY interface
selection must be configured with the DWMAC block in reset.
This layer covers a block containing only two registers. Although it
is possible to model this as a reset controller and use the "resets"
property of stmmac, it's much more intuitive to include this in the
glue layer instead.
At this time only RGMII is supported, because it is the only mode
which has been validated hardware-wise.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With new transparent VF support, it is possible to get a deadlock
when some of the deferred work is running and the unregister_vf
is trying to cancel the work element. The solution is to use
trylock and reschedule (similar to bonding and team device).
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing with a background iperf pushing 1Gbit/sec worth of
traffic and having both ifconfig and ethtool collect statistics, we
could see quite frequent deadlocks. Convert the often accessed DSA slave
network devices statistics to per-cpu 64-bit statistics to remove these
deadlocks and provide fast efficient statistics updates.
Fixes: f613ed665b ("net: dsa: Add support for 64-bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng says:
====================
tcp cwnd undo refactor
This patch series consolidate similar cwnd undo functions
implemented by various congestion control by using existing
tcp socket state variable. The first patch fixes a corner
case in of cwnd undo in Reno and HTCP. Since the bug has
existed for many years and is very minor, we consider this
patch set more suitable for net-next as the major change
is the refactor itself.
- v1->v2
Fix trivial compile errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Most TCP congestion controls are using identical logic to undo
cwnd except BBR. This patch consolidates these similar functions
to the one used currently by Reno and others.
Suggested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using ssthresh to revert cwnd is less reliable when ssthresh is
bounded to 2 packets. This patch uses an existing variable in TCP
"prior_cwnd" that snapshots the cwnd right before entering fast
recovery and RTO recovery in Reno. This fixes the issue discussed
in netdev thread: "A buggy behavior for Linux TCP Reno and HTCP"
https://www.spinics.net/lists/netdev/msg444955.html
Suggested-by: Neal Cardwell <ncardwell@google.com>
Reported-by: Wei Sun <unlcsewsun@gmail.com>
Signed-off-by: Yuchung Cheng <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing sub channel code did not wait for all the sub-channels
to completely initialize. This could lead to race causing crash
in napi_netif_del() from bad list. The existing code would send
an init message, then wait only for the initial response that
the init message was received. It thought it was waiting for
sub channels but really the init response did the wakeup.
The new code keeps track of the number of open channels and
waits until that many are open.
Other issues here were:
* host might return less sub-channels than was requested.
* the new init status is not valid until after init was completed.
Fixes: b3e6b82a00 ("hv_netvsc: Wait for sub-channels to be processed during probe")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using Broadcom Systemport device in 32bit Platform, ifconfig can
only report up to 4G tx,rx status, which will be wrapped to 0 when the
number of incoming or outgoing packets exceeds 4G, only taking
around 2 hours in busy network environment (such as streaming).
Therefore, it makes hard for network diagnostic tool to get reliable
statistical result, so the patch is used to add 64bit support for
Broadcom Systemport device in 32bit Platform.
This patch provides 64bit statistics capability on both ethtool and ifconfig.
Signed-off-by: Jianming.qiao <kiki-good@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving PF module param console_bitmask to lio_main.c for consistency.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's supposed to be a one-to-one correspondence between the 18 macros
that #define the OCT_DEV states (in octeon_device.h) and the strings in the
oct_dev_state_str array, but there are only 14 strings in the array.
Add the missing strings (so they become 18 in total), and also revise some
incorrect/outdated text of existing strings.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
phylink and sfp support
This patch series introduces generic support for SFP sockets found on
various Marvell based platforms. The idea here is to provide common
SFP socket support which can be re-used by network drivers as
appropriate, rather than each network driver having to re-implement
SFP socket support.
SFP sockets typically use other system resources, eg, I2C buses to read
identifying information, and GPIOs to monitor socket state and control
the socket. Meanwhile, some network drivers drive multiple ethernet
ports from one instantiation of the driver.
It is not desirable to block the initialisation of a network driver
(thus denying other ports from being operational) if the resources
for the SFP socket are not yet available. This means that an element
of independence between the SFP support code and the driver is
required.
More than that, SFP modules effectively bring hotplug PHYs to
networking - SFP copper modules normally contain a standard PHY
accessed over the I2C bus, and it is desirable to read their state
so network drivers can be appropriately configured.
To add to the complexity, SFP modules can be connected in at least
two places:
1. Directly to the serdes output of a MAC with no intervening PHY.
For example:
mvneta ----> SFP socket
2. To a PHY, for example:
mvpp2 ---> PHY ---> copper
|
`-----> SFP socket
This code supports both setups, although it's not fully implemented
with scenario (2).
Moreover, the link presented by the SFP module can be one of the
10Gbase-R family (for SFP+ sockets), SGMII or 1000base-X (for SFP
sockets) depending on the module, and network drivers need to
reconfigure themselves accordingly for the link to come up.
For example, if the MAC is configured for SGMII and a fibre module
is plugged in, the link won't come up until the MAC is reconfigured
for 1000base-X mode.
The SFP code manages the SFP socket - detecting the module, reading
the identifying information, and managing the control and status
signals. Importantly, it disables the SFP module transmitter when
the MAC is down, so that the laser is turned off (but that is not
a guarantee.)
phylink provides the mechanisms necessary to manage the link modes,
based on the SFP module type, and supports hot-plugging of the PHY
without needing the MAC driver to be brought up and down on
transitions. phylink also supports the classical static PHY and
fixed-link modes.
I currently (but not included in this series) have code to convert
mvneta to use phylink, and the out of tree mvpp2x driver. I have
nothing for the mvpp2 driver at present as that driver is only
recently becoming functional on 10G hardware, and is missing a lot
of features that are necessary to make things work correctly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFP hotpluggable modules via sfp-bus and phylink.
This supports both copper and optical SFP modules, which require
different Serdes modes in order to properly negotiate the link.
Optical SFP modules typically require the Serdes link to be talking
1000BaseX mode - this is the gigabit ethernet mode defined by the
802.3 standard.
Copper SFP modules typically integrate a PHY in the module to convert
from Serdes to copper, and the PHY will be configured by the vendor
to either present a 1000BaseX Serdes link (for fixed 1000BaseT) or a
SGMII Serdes link. However, this is vendor defined, so we instead
detect the PHY, switch the link to SGMII mode, and use traditional
PHY based negotiation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in-band autonegotation support for 10GBase-KR mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading and writing the clause 45 MII registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading module EEPROMs through phylink.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an I2C MDIO bus bridge library, to allow phylib to access PHYs which
are connected to an I2C bus instead of the more conventional MDIO bus.
Such PHYs can be found in SFP adapters and SFF modules.
Since PHYs appear at I2C bus address 0x40..0x5f, and 0x50/0x51 are
reserved for SFP EEPROMs/diagnostics, we must not allow the MDIO bus
to access these I2C addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink will need phy_start_machine exported, so lets export it as a
GPL symbol. Documentation/networking/phy.txt indicates that this
should be a PHY API function.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing 1000Base-X entry to the phy settings table. This was
not included because the original code could not cope with more than
32 bits of link mode mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the phy settings table to support more than 32 link modes by
switching to the ethtool link mode bit number representation, rather
than storing the mask. This will allow phylink and other ethtool
code to share the settings table to look up settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
IP: cleanup LSRR option processing
The __ip_options_echo() function expect a valid dst entry in skb->dst;
as result we sometimes need to preserve the dst entry for the whole IP
RX path.
The current usage of skb->dst looks more a relic from ancient past that
a real functional constraint. This patchset tries to remove such usage,
and than drops some hacks currently in place in the IP code to keep
skb->dst around.
__ip_options_echo() uses of skb->dst for two different purposes: retrieving
the netns assicated with the skb, and modify the ingress packet LSRR address
list.
The first patch removes the code modifying the ingress packet, and the second
one provides an explicit netns argument to __ip_options_echo(). The following
patches cleanup the current code keeping arund skb->dst for __ip_options_echo's
sake.
Updating the __ip_options_echo() function has been previously discussed here:
http://marc.info/?l=linux-netdev&m=150064533516348&w=2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
__ip_options_echo() does not need anymore skb->dst, so we can
avoid explicitly preserving it for its own sake.
This is almost a revert of commit 0ddf3fb2c4 ("udp: preserve
skb->dst if required for IP options processing") plus some
lifting to fit later changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_options_echo() does not use anymore the skb->dst and don't
need to keep the dst around for options's sake only.
This reverts commit 34b2cef20f.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ip_options_echo() uses the current network namespace, and
currently retrives it via skb->dst->dev.
This commit adds an explicit 'net' argument to __ip_options_echo()
and update all the call sites to provide it, usually via a simpler
sock_net().
After this change, __ip_options_echo() no more needs to access
skb->dst and we can drop a couple of hack to preserve such
info in the rx path.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While computing the response option set for LSRR, ip_options_echo()
also changes the ingress packet LSRR addresses list, setting
the last one to the dst specific address for the ingress packet
- via memset(start[ ...
The only visible effect of such change - beyond possibly damaging
shared/cloned skbs - is modifying the data carried by ICMP replies
changing the header information for reported the ingress packet,
which violates RFC1122 3.2.2.6.
All the others call sites just ignore the ingress packet IP options
after calling ip_options_echo()
Note that the last element in the LSRR option address list for the
reply packet will be properly set later in the ip output path
via ip_options_build().
This buggy memset() predates git history and apparently was present
into the initial ip_options_echo() implementation in linux 1.3.30 but
still looks wrong.
The removal of the fib_compute_spec_dst() call will help
completely dropping the skb->dst usage by __ip_options_echo() with a
later patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix loop preventing some platforms from waking up via the power
button in s2idle.
intel-vbtn:
- match power button on press rather than release
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZhjtgAAoJEKbMaAwKp3647u4IALEnsRt10hj2ognbpQUPxqzB
uwjlQ7ukqwWVbpgElQ6q2hKUFHNnk2CGuzIEjvRKpme0UpsSPUQRPZGeUGDmvC3l
cOxNSmyTJkmeCEU9G7yj1NrcaOEFQ9iRLrZmSRnYBSWBgjzYdpfC/xog2y8mVkgO
FQAU2ul9Ph5eXEOTQBw56LtzsraJtBdV76aKESuJEAw3h0E8svhLeV43caVic/Go
Yv9aRZRkj/5oQHwXe+GC5K4dFdWFYZ9iGLQFHgcICRACcUq7p0ysVvf8YMVQplyR
Xm2j8Dq1ierId5g90p5fznIM4BeBnIM2Iclkk4dPaIrP3Fogd9eq1gvxQKvWgpY=
=IOnZ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlmHbBAACgkQ8vlZVpUN
gaMu3gf+LpI5bI1XA3R8KbXB2snnz6wM7OzArfqvreX+m+xP1CK6nVpAIgpkZqfw
QkQ1xPJk7Q25vex/pPcsgLO0Vxf0i4vpydK+fYnf30S4WvGQVq6OHZWFFv2zM2YB
7TWxjG+KryM7j6JSXdUiSTKP3nX84TW/IMIWuZMR1nuOa8N5M4yD3uc+3EBTjSbq
P/dxfmkp2hQKnlZVBWqCjJDhtxwUYTF4iZ/pbSVeGbgHCh1674ml+airb4K9ltNU
0vR0JChD12YJaafjaAyIrqqKwDGvnN+H5wyhCodEV9w8jthbcU04Jfmi1auB9UxT
y7/sgbV64W2o5hBwxY3RXjZkVLpDsw==
=Mtr7
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
The latest change of compat_sys_sigpending in commit 8f13621abc
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621abc ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes: 1c6bd7173d
Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
