When ECPF eswitch manager is at offloads mode, it monitors functions
changed event from host PF side and acts according to the number of
VFs enabled/disabled.
As ECPF and host PF work in two independent hosts, it's possible that
host PF OS reboots but ECPF system is still kept on and continues
monitoring events from host PF. When kernel from host PF side is
booting, PCI iov driver does sriov_init and compute_max_vf_buses by
iterating over all valid num of VFs. This triggers FLR and generates
functions changed events, even though host PF HCA is not enabled at
this time. However, ECPF is not aware of this information, and still
handles these events as usual. ECPF system will see massive number of
reps are created, but destroyed immediately once creation finished.
To eliminate this noise, a bit is added to host parameter context to
indicate host PF is disabled. ECPF will not handle the VF changed
event if this bit is set.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Given a fw component index, the MCQI register allows us to query
this component's information (e.g. its version and capabilities).
Given a fw component index, the MCQS register allows us to query the
status of a fw component, including its type and state
(e.g. PRESET/IN_USE).
It can be used to find the index of a component of a specific type, by
sequentially increasing the component index, and querying each time the
type of the returned component.
If max component index is reached, 'last_index_flag' is set by the HCA.
These registers' description was added to query the running and pending
fw version of the HCA.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Update mlx5 device interface data structures for:
1. New command definitions for allocating, deallocating SF
2. Query SF partition
3. Eswitch SF fields
4. HCA CAP SF fields
5. Extend Eswitch functions command for SF
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a dual-port VHCA sends a RoCE packet on its non-native port, and
the packet arrives to its affiliated vport FDB, a mismatch might occur
on the rules that match the packet source vport. So we replace the
match on source port with the match on metadata that was configured in
ingress ACL, and that metadata will be passed further also to the NIC
RX table of the eswitch manager.
Introduce vport metadata matching bits and enum constants as a pre-step
towards metadata matching.
o metadata type C registers in the misc parameters 2 fields.
o esw_uplink_ingress_acl bit in esw cap. If it set, the device supports
ingress ACL for the uplink vport.
o fdb_to_vport_reg_* bits in flow table cap and esw vport context, to
support propagating the metadata to the nic rx through the loopback
path.
o flow_source in flow context, to indicate the known origin of packets.
o enum constants, to support the above bits.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For ECPF with eswitch manager privilege, query the host max VF count
by querying the device using query_functions command.
With this enhancement:
1. flow steering entries are created only for valid vports based on
the max VF count of the PF.
2. Driver only queries cap of valid vport.
Eswitch requires the max VFs when doing initialization, so do sr-iov
init before eswitch init.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Whenever device supports eswitch functions changed event, honor
such device setting. Do not limit it to ECPF.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To support sriov on a E-Switch manager, num_vfs are queried
to the firmware whenever E-Switch manager is notified by
esw_functions_changed event.
Replace host_params event with esw_functions_changed event that reflects
more appropriate naming.
While at it, also correct num_vfs type from int to u16 as expected by
the function mlx5_esw_query_functions().
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Termination table is a flow table with a termination flag. The flag
allows the firmware to assume that the the specified actions are the last
actions list. This assumption allows the FW to safely perform potential
looping logic (e.g. hairpin). Introduce the bits for this attribute.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is being sent to get a fix for the gcc 9.1 build warnings, and I've
also pulled in some bug fix patches that were posted in the last two
weeks.
- Avoid the gcc 9.1 warning about overflowing a union member
- Fix the wrong callback type for a single response netlink to doit
- Bug fixes from more usage of the mlx5 devx interface
-----BEGIN PGP SIGNATURE-----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=Lo/s
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull more rdma updates from Jason Gunthorpe:
"This is being sent to get a fix for the gcc 9.1 build warnings, and
I've also pulled in some bug fix patches that were posted in the last
two weeks.
- Avoid the gcc 9.1 warning about overflowing a union member
- Fix the wrong callback type for a single response netlink to doit
- Bug fixes from more usage of the mlx5 devx interface"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
net/mlx5: Set completion EQs as shared resources
IB/mlx5: Verify DEVX general object type correctly
RDMA/core: Change system parameters callback from dumpit to doit
RDMA: Directly cast the sockaddr union to sockaddr
Mark completion EQs as shared resources so that they can be used by CQs
with uid != 0.
Fixes: 7efce3691d ("IB/mlx5: Add obj create and destroy functionality")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Aya: Enable general events on all physical link types and
restrict general event handling of subtype DELAY_DROP_TIMEOUT in mlx5 rdma
driver to ethernet links only as it was intended.
2) From Eli: Introduce low level bits for prio tag mode
3) From Maor: Low level steering updates to support RDMA RX flow
steering and enables RoCE loopback traffic when switchdev is enabled.
4) From Vu and Parav: Two small mlx5 core cleanups
5) From Yevgeny add HW definitions of geneve offloads
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cited commit broke the offsets of hca cap struct, fix it.
While at it, cleanup a white space introduced by the same commit.
Fixes: b169e64a24 ("net/mlx5: Geneve, Add flow table capabilities for Geneve decap with TLV options")
Reported-by: Qian Cai <cai@lca.pw>
Cc: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce specification for Geneve decap flow with encapsulation options
and allow creation of rules that are matching on Geneve TLV options.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce support for Geneve flow specification and allow
the creation of rules that are matching on basic Geneve
protocol fields: VNI, OAM bit, protocol type, options length.
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow table supports three types of miss action:
1. Default miss action - go to default miss table according to table.
2. Go to specific table.
3. Switch domain - go to the root table of an alternative steering
table domain.
New table miss action was added - switch_domain.
The next domain for RDMA_RX namespace is the NIC RX domain.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add new flow steering namespace - MLX5_FLOW_NAMESPACE_RDMA_RX.
Flow steering rules in this namespace are used to filter
RDMA traffic.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets will be
tagged with VLAN ID 0x000 (priority tag) and pop/push actions will be
replaced by VLAN re-write actions (which are supported by the HW).
Introduce prio tag mode as a pre-step to controlling the workaround
behavior.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding the TIR ICM address to the create_tir command outbox
through which the device reports the ICM address of the newly
created TIR.
The TIR address can be used for direct attachment to a steering
rule in SW managed steering mode.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add SW ICM related fields to the device memory capabilities
structure and sw ownership capability in flow table properties.
The currently supported SW ICM types are steering and header modify
and the changes exposes the device memory capabilities for each
of these two types.
SW ICM memory can be allocated by SW and then be accessed by RDMA
operations for direct management of the HW packet handling tables.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlyOup0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGHKoIAIKVuBSyD+m65TaM
pjoAFa56weEc67Mmai2A84EOm0MVy9C6L7EOcOgVsJiLxDCYyWQ7xYwV2kceKJpW
H5xauhb3+TxpxYeaeKdPPPHmBdejRwOPYvGAfnDMCqCCWQTad52sQUPCLI+yhF1t
wgnuMi+SwNBWP9aYCXdFPK4fVhh27AcEAOEsRVCh4tIBH/wkf4GwrDr3IX1MFeMX
jE/R43la4hu1swcWBsjkErWUasVPCgJSSQTfKDo9PQTVnoh0PHFp4fkOInVKLymQ
7AGo+Knc+1he+sFsB2IbZwea0xqtJtjtr1oC+at8gNx66qVG+o7UZNi5LR1uPW4Z
4+dwGBk=
=pyXR
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mlx5-next
Linux 5.1-rc1
We forgot to reset the branch last merge window thus mlx5-next is outdated
and still based on 5.0-rc2. This merge commit is needed to sync mlx5-next
branch with 5.1-rc1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This merge commit includes some misc shared code updates from mlx5-next branch needed
for net-next.
1) From Maxim, Remove un-used macros and spinlock from mlx5 code.
2) From Aya, Expose Management PCIE info register layout and add rate limit
print macros.
3) From Tariq, Compilation warning fix in fs_core.c
4) From Vu, Huy and Saeed, Improve mlx5 initialization flow:
The goal is to provide a better logical separation of mlx5 core
device initialization flow and will help to seamlessly support
creating different mlx5 device types such as PF, VF and SF
mlx5 sub-function virtual devices.
Mlx5_core driver needs to separate HCA resources from pci resources.
Its initialize/load/unload will be broken into stages:
1. Initialize common data structures
2. Setup function which initializes pci resources (for PF/VF)
or some other specific resources for virtual device
3. Initialize software objects according to hardware capabilities
4. Load all mlx5_core components
It is also necessary to detach mlx5_core mdev name/message from pci
device mdev->pdev name/message for a clearer report/debug of
different mlx5 device types.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Expose PRM layout for handling MPEIN (Management PCIE Info). It will be
used in the downstream patch for querying MPEIN via the driver.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add VLAN ID rewrite fields as a pre-step to support this rewrite.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When using the device packet encapsulation offload, the device
calculates an entropy value, representing the inner packet headers. The
entropy field is placed inside the outer packet headers. For UDP-type
encapsulations, the entropy is placed in the source port field of the
UDP header. For GRE-type encapsulations, the entropy is placed in the 8
LSB of the key field in the GRE header. If the device does not recognize
the encapsulation type, the entropy is not placed in the packet.
Entropy setting can be controlled using PCMR register. if encapsulation
offload is not used force_entropy_cap should be set to 0x0. Entropy
setting is enabled/disabled using entropy_calc, and could be
additionally enabled/disabled for GRE encapsulation by entropy_gre_calc.
As a pre-step to automatically control the tunnel entropy, introduce
the entropy fields in the PCMR register with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.
1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
responsibility. A rep of the host PF shall be created at the ECPF
side for the eswitch manager to control.
2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
ECPF acts similar as a VF to the host PF. Host PF will be aware
of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Register Port Type and Speed (PTYS) introduces three new fields
extending the speed/protocols the can be reported and configured.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The QUERY_HOST_PARAMS command is used by an Embedded CPU Physical
Function (ECPF) driver to identify and retrieve information about the
PF on the host side. E.g, number of virtual functions and PCI BDF.
The number of VFs can be changed on the fly, a function is added to
query current number of VFs and will be used in downstream patches.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With the introduction of ECPF, we require that the ECPF driver will
aways call enable/disable HCA for that PF in the same way a PF does
this for its VFs. The PF is still responsible for calling enable and
disable HCA for its VFs.
To distinguish between the ECPF executing enable/disable HCA for
itself or for the PF, it sets the embedded CPU function bit in the
input params struct of these commands. When the bit is cleared and
function ID is zero, it refers to the peer PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Mellanox's SmartNIC combines embedded CPU(e.g, ARM) processing power
with advanced network offloads to accelerate a multitude of security,
networking and storage applications.
With the introduction of the SmartNIC, there is a new PCI function
called Embedded CPU Physical Function(ECPF). And it's possible for a
PF to get its ICM pages from the ECPF PCI function. Driver shall
identify if it is running on such a function by reading a bit in
the initialization segment.
When firmware asks for pages, it would issue a page request event
specifying how many pages it requests and for which function. That
driver responds with a manage_pages command providing the requested
pages along with an indication for which function it is providing these
pages.
The encoding before this patch was as follows:
function_id == 0: pages are requested for the function receiving
the EQE.
function_id != 0: pages are requested for VF identified by the
function_id value
A new one bit field in the EQE identifies that pages are requested for
the ECPF.
The notion of page_supplier can be introduced here and to support that,
manage pages and query pages were modified so firmware can distinguish
the following cases:
1. Function provides pages for itself
2. PF provides pages for its VF
3. ECPF provides pages to itself
4. ECPF provides pages for another function
This distinction is possible through the introduction of the bit
"embedded_cpu_function" in query_pages, manage_pages and page request
EQE.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
To avoid compatibility issue with older kernels the firmware doesn't
allow SRQ to work with ODP unless kernel asks for it.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
The device capabilities for ODP structure was missing the field for XRC
transport so add it here.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting to
get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4, mlx5,
qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use write()
for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into
a big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and sysfs
files
- First steps toward removing 'uobject' from the view of the drivers
-----BEGIN PGP SIGNATURE-----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=T0p1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting
to get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4,
mlx5, qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use
write() for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into a
big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page
tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and
sysfs files
- First steps toward removing 'uobject' from the view of the drivers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (193 commits)
RDMA/srpt: Use kmem_cache_free() instead of kfree()
RDMA/mlx5: Signedness bug in UVERBS_HANDLER()
IB/uverbs: Signedness bug in UVERBS_HANDLER()
IB/mlx5: Allocate the per-port Q counter shared when DEVX is supported
IB/umad: Start using dev_groups of class
IB/umad: Use class_groups and let core create class file
IB/umad: Refactor code to use cdev_device_add()
IB/umad: Avoid destroying device while it is accessed
IB/umad: Simplify and avoid dynamic allocation of class
IB/mlx5: Fix wrong error unwind
IB/mlx4: Remove set but not used variable 'pd'
RDMA/iwcm: Don't copy past the end of dev_name() string
IB/mlx5: Fix long EEH recover time with NVMe offloads
IB/mlx5: Simplify netdev unbinding
IB/core: Move query port to ioctl
RDMA/nldev: Expose port_cap_flags2
IB/core: uverbs copy to struct or zero helper
IB/rxe: Reuse code which sets port state
IB/rxe: Make counters thread safe
IB/mlx5: Use the correct commands for UMEM and UCTX allocation
...
During testing the command format was changed to close a security
hole. Revise the driver to use the command format that will actually be
supported in GA firmware.
Both the UMEM and UCTX are intended only for use by the kernel and cannot
be executed using a general command.
Since the UMEM and CTX are not part of the general object the caps bits
were moved to be some log_xxx location in the general HCA caps.
The firmware code was adapted as well to match the above.
Fixes: a8b92ca1b0 ("IB/mlx5: Introduce DEVX")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on following patches.
* branche 'mlx5-next': (23 commits)
IB/mlx5: Introduce uid as part of alloc/dealloc transport domain
net/mlx5: Add shared Q counter bits
net/mlx5: Continue driver initialization despite debugfs failure
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
net/mlx5: Remove the get protocol device interface entry
net/mlx5: Support extended destination format in flow steering command
net/mlx5: E-Switch, Change vhca id valid bool field to bit flag
net/mlx5: Introduce extended destination fields
net/mlx5: Revise gre and nvgre key formats
net/mlx5: Add monitor commands layout and event data
net/mlx5: Add support for plugged-disabled cable status in PME
net/mlx5: Add support for PCIe power slot exceeded error in PME
net/mlx5: Rework handling of port module events
net/mlx5: Move flow counters data structures from flow steering header
...
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce uid as part of alloc/dealloc transport domain to match the
device specification.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Updated HW specification file with needed bits to allow
sharing of Q counters between DEVX contexts and kernel.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
mlx5-next shared branch with rdma subtree to avoid mlx5 rdma v.s. netdev
conflicts.
Highlights:
1) Lag refactroing and flow counter affinity bits.
2) mlx5 core cleanups
By Roi Dayan (2) and others
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This dictates the device affinity for eswitch flow counters, set by the FW
according to the HW device capabilities.
Under "source eswitch" affinity, the counter should be allocated on the
device related to the source vport in the match. This covers both non
merged e-switch mode as well as old FW that does not advertise this cap.
Under "flow eswitch" affinity, the counter should be allocated on the
device where the eswitch rule is set.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Apparently gcc is cool with upper case '0X' but it is not commonly used.
Replace '0X' with lowercase '0x' in mlx5_ifc.h file.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cap bits locations for the fdb caps of multi path to table (used for
local mirroring) and multi encap (used for prio/chains) were wrongly used
in swapped locations. This went unnoted so far b/c we tested the offending
patch with CX5 FW that supports both of them. On different environments where
not both caps are supported, we will be messed up, fix that.
Fixes: b9aa0ba17a ('net/mlx5: Add cap bits for multi fdb encap')
Signed-off-by: Vu Pham <vu@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Extended destinations provide the ability to configure different
encapsulation properties per destination on a single FTE. This is
needed for use-cases such as remote mirroring over tunneled networks.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
GRE RFC defines a 32 bit key field. NVGRE RFC splits the 32 bit
key field to 24 bit VSID (gre_key_h) and 8 bit flow entropy (gre_key_l).
Define the two key parsing alternatives in a union, thus enabling both
access methods.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Will be used in downstream patch to monitor counter changes
by the HCA and report it to the driver by an event.
The driver will update its counters cached data accordingly.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Danit Goldberg says:
Packet based credit mode
Packet based credit mode is an alternative end-to-end credit mode for QPs
set during their creation. Credits are transported from the responder to
the requester to optimize the use of its receive resources. In
packet-based credit mode, credits are issued on a per packet basis.
The advantage of this feature comes while sending large RDMA messages
through switches that are short in memory.
The first commit exposes QP creation flag and the HCA capability. The
second commit adds support for a new DV QP creation flag. The last commit
report packet based credit mode capability via the MLX5DV device
capabilities.
* branch 'mlx5-packet-credit-fc':
IB/mlx5: Report packet based credit mode device capability
IB/mlx5: Add packet based credit mode support
net/mlx5: Expose packet based credit mode
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Packet based credit mode bit determines whether the credit mode
is done per message or packet. Expose the QP creation flag and
the HCA capability.
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Update the supported DEVX commands, it includes adding to the
query/modify command's list and to the encoding handling.
In addition, a valid range for general commands was added to be used for
future commands.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Expose device capabilities for DEVX user context, it includes which caps
the device is supported and a matching bit to set as part of user
context creation.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
