John Blackwood reported:
> on an older Dell PowerEdge 6650 system with 8 cpus (4 are hyper-threaded),
> and 32 bit (x86) kernel, once you change the irq smp_affinity of an irq
> to be less than all cpus in the system, you can never change really the
> irq smp_affinity back to be all cpus in the system (0xff) again,
> even though no error status is returned on the "/bin/echo ff >
> /proc/irq/[n]/smp_affinity" operation.
>
> This is due to that fact that BAD_APICID has the same value as
> all cpus (0xff) on 32bit kernels, and thus the value returned from
> set_desc_affinity() via the cpu_mask_to_apicid_and() function is treated
> as a failure in set_ioapic_affinity_irq_desc(), and no affinity changes
> are made.
set_desc_affinity() is already checking if the incoming cpu mask
intersects with the cpu online mask or not. So there is no need
for the apic op cpu_mask_to_apicid_and() to check again
and return BAD_APICID.
Remove the BAD_APICID return value from cpu_mask_to_apicid_and()
and also fix set_desc_affinity() to return -1 instead of using BAD_APICID
to represent error conditions (as cpu_mask_to_apicid_and() can return
logical or physical apicid values and BAD_APICID is really to represent
bad physical apic id).
Reported-by: John Blackwood <john.blackwood@ccur.com>
Root-caused-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1261103386.2535.409.camel@sbs-t61>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'timers-for-linus-hpet' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hpet: Make WARN_ON understandable
x86: arch specific support for remapping HPET MSIs
intr-remap: generic support for remapping HPET MSIs
x86, hpet: Simplify the HPET code
x86, hpet: Disable per-cpu hpet timer if ARAT is supported
In the case when cpu goes offline, fixup_irqs() will forward any
unhandled interrupt on the offlined cpu to the new cpu
destination that is handling the corresponding interrupt. This
interrupt forwarding is done via IPI's. Hence, in this case also
level-triggered io-apic interrupt will be seen as an edge
interrupt in the cpu's APIC IRR.
Document this scenario in the code which handles this case by doing
an explicit EOI to the io-apic to clear remote IRR of the io-apic RTE.
Requested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: ebiederm@xmission.com
Cc: garyhade@us.ibm.com
LKML-Reference: <20091201233335.143970505@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Maciej W. Rozycki reported:
> 82093AA I/O APIC has its version set to 0x11 and it
> does not support the EOI register. Similarly I/O APICs
> integrated into the 82379AB south bridge and the 82374EB/SB
> EISA component.
IO-APIC versions below 0x20 don't support EOI register.
Some of the Intel ICH Specs (ICH2 to ICH5) documents the io-apic
version as 0x2. This is an error with documentation and these
ICH chips use io-apic's of version 0x20 and indeed has a working
EOI register for the io-apic.
Fix the EOI register detection mechanism to check for version
0x20 and beyond.
And also, a platform can potentially have io-apic's with
different versions. Make the EOI register check per io-apic.
Reported-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: ebiederm@xmission.com
Cc: garyhade@us.ibm.com
LKML-Reference: <20091201233335.065361533@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the level-triggered interrupt is seen as an edge interrupt,
we try to clear the remoteIRR explicitly (using either an
io-apic eoi register when present or through the idea of
changing trigger mode of the io-apic RTE to edge and then back
to level). But this explicit try also needs to happen before we
try to migrate the irq. Otherwise irq migration attempt will
fail anyhow, as it postpones the irq migration to a later
attempt when it sees the remoteIRR in the io-apic RTE still set.
Signed-off-by: "Maciej W. Rozycki" <macro@linux-mips.org>
Reviewed-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: ebiederm@xmission.com
Cc: garyhade@us.ibm.com
LKML-Reference: <20091201233334.975416130@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When irq_desc is moved, we need to make sure to use the right cfg_new.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B07A739.3030104@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If IO-APIC base address is 1K aligned we should not fail
on resourse insertion procedure. For this sake we define
IO_APIC_SLOT_SIZE constant which should cover all IO-APIC
direct accessible registers.
An example of a such configuration is there
http://marc.info/?l=linux-kernel&m=118114792006520
|
| Quoting the message
|
| IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
| IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47
| IOAPIC[2]: apic_id 4, version 32, address 0xfec80400, GSI 48-71
| IOAPIC[3]: apic_id 5, version 32, address 0xfec84000, GSI 72-95
| IOAPIC[4]: apic_id 8, version 32, address 0xfec84400, GSI 96-119
|
Reported-by: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20091116151426.GC5653@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should not use physid_mask_t as a stack based
variable in apic code. This type depends on MAX_APICS
parameter which may be huge enough.
Especially it became a problem with apic NOOP driver which
is portable between 32 bit and 64 bit environment
(where we have really huge MAX_APICS).
So apic driver should operate with pointers and a caller
in turn should aware of allocation physid_mask_t variable.
As a side (but positive) effect -- we may use already
implemented physid_set_mask_of_physid function eliminating
default_apicid_to_cpu_present completely.
Note that physids_coerce and physids_promote turned into static
inline from macro (since macro hides the fact that parameter is
being interpreted as unsigned long, make it explicit).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20091109220659.GA5568@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should be ready that one day MAX_IO_APICS may raise its
number. To prevent memory overwrite we're to use safe
snprintf while set IO-APIC resourse name.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20091108155431.GC25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The whole page is reserved for IO-APIC fixmap
due to non-cacheable requirement. So lets note
this explicitly instead of playing with numbers.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
LKML-Reference: <20091108155356.GB25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IO-APIC's in intel chipsets support EOI register starting from
IO-APIC version 2. Use that when ever we need to clear the
IO-APIC RTE's RemoteIRR bit explicitly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.947855317@sbs-t61.sc.intel.com>
[ Marked use_eio_reg as __read_mostly, fixed small details ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a cpu goes offline, fixup_irqs() try to move irq's
currently destined to the offline cpu to a new cpu. But this
attempt will fail if the irq is recently moved to this cpu and
the irq still hasn't arrived at this cpu (for non intr-remapping
platforms this is when we free the vector allocation at the
previous destination) that is about to go offline.
This will endup with the interrupt subsystem still pointing the
irq to the offline cpu, causing that irq to not work any more.
Fix this by forcing the irq to complete its move (its been a
long time we moved the irq to this cpu which we are offlining
now) and then move this irq to a new cpu before this cpu goes
offline.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.848830905@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move_cleanup_count for each irq in irq_cfg is keeping track of
the total number of cpus that need to free the corresponding
vectors associated with the irq which has now been migrated to
new destination. As long as this move_cleanup_count is non-zero
(i.e., as long as we have n't freed the vector allocations on
the old destinations) we were preventing the irq's further
migration.
This cleanup count is unnecessary and it is enough to not allow
the irq migration till we send the cleanup vector to the
previous irq destination, for which we already have irq_cfg's
move_in_progress. All we need to make sure is that we free the
vector at the old desintation but we don't need to wait till
that gets freed.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.752968906@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move UV specific functionality out of the generic IO-APIC code.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20091013203236.GD20543@sgi.com>
[ Cleaned up the code some more in their new places. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes handling of uv hub irq affinity. IRQs with ALL or
NODE affinity can be routed to cpus other than their originally
assigned cpu. Those with CPU affinity cannot be rerouted.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20090930160259.GA7822@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case if a system has a large number of cpus printing apics
contents may consume a long time period.
We limit such an output by 1 apic by default. But to have an
ability to see all apics or some part of them we introduce
"show_lapic" setup option which allow us to limit/unlimit the
number of APICs being dumped.
Example: apic=debug show_lapic=5, or apic=debug show_lapic=all
Also move apic_verbosity checking upper that way so helper routines
do not need to inspect it at all.
Suggested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
Cc: macro@linux-mips.org
LKML-Reference: <20091013201022.926793122@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove open-coded zalloc_cpumask_var() and zalloc_cpumask_var_node().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In case of discrete (pretty old) apics we may have cpu_has_apic bit
not set but have to check if smp_found_config (MP spec) is there
and apic was not disabled.
Also don't forget to print apic/io-apic for such case as well.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090915071230.GA10604@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
x86: Move get/set_wallclock to x86_platform_ops
x86: platform: Fix section annotations
x86: apic namespace cleanup
x86: Distangle ioapic and i8259
x86: Add Moorestown early detection
x86: Add hardware_subarch ID for Moorestown
x86: Add early platform detection
x86: Move tsc_init to late_time_init
x86: Move tsc_calibration to x86_init_ops
x86: Replace the now identical time_32/64.c by time.c
x86: time_32/64.c unify profile_pc
x86: Move calibrate_cpu to tsc.c
x86: Make timer setup and global variables the same in time_32/64.c
x86: Remove mca bus ifdef from timer interrupt
x86: Simplify timer_ack magic in time_32.c
x86: Prepare unification of time_32/64.c
x86: Remove do_timer hook
x86: Add timer_init to x86_init_ops
x86: Move percpu clockevents setup to x86_init_ops
x86: Move xen_post_allocator_init into xen_pagetable_setup_done
...
Fix up conflicts in arch/x86/include/asm/io_apic.h
The proposed Moorestown support patches use an extra feature flag
mechanism to make the ioapic work w/o an i8259. There is a much
simpler solution.
Most i8259 specific functions are already called dependend on the irq
number less than NR_IRQS_LEGACY. Replacing that constant by a
read_mostly variable which can be set to 0 by the platform setup code
allows us to achieve the same without any special feature flags.
That trivial change allows us to proceed with MRST w/o doing a full
blown overhaul of the ioapic code which would delay MRST unduly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge reason: the SFI (Simple Firmware Interface) feature in the ACPI
tree needs this cleanup, pull it into the APIC branch as
well so that there's no interactions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some IO-APIC routines are ACPI specific now, but need to
be exposed when CONFIG_ACPI=n for the benefit of SFI.
Remove #ifdef ACPI around these routines:
io_apic_get_unique_id(int ioapic, int apic_id);
io_apic_get_version(int ioapic);
io_apic_get_redir_entries(int ioapic);
Move these routines from ACPI-specific boot.c to io_apic.c:
uniq_ioapic_id(u8 id)
mp_find_ioapic()
mp_find_ioapic_pin()
mp_register_ioapic()
Also, since uniq_ioapic_id() is now no longer static,
re-name it to io_apic_unique_id() for consistency
with the other public io_apic routines.
For simplicity, do not #ifdef the resulting code ACPI || SFI,
thought that could be done in the future if it is important
to optimize the !ACPI !SFI IO-APIC x86 kernel for size.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
x86 arch support for remapping HPET MSI's by associating the HPET timer block
with the interrupt-remapping HW unit and setting up appropriate irq_chip
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jay Fenlason <fenlason@redhat.com>
LKML-Reference: <20090804190729.630510000@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
32bit and also the numaq code have special requirements on the
ioapic_id setup. Convert it to a x86_init_ops function and get rid
of the quirks and #ifdefs
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
alloc_bootmem() already panics on allocation failure. There is
no need to check the result.
Also there is a way to unbind global variable from its body and
use it as a parameter which allow us to simplify
ioapic_init_mappings as well -- "for" cycle already uses
nr_ioapics as a conditional variable and there is no need to
check if ioapic_setup_resources was returning NULL again.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090824175551.493629148@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Though the most time we are to panic on irq-pin allocation
fails, for PCI interrupts it's not the case and we could
continue operate even if irq-pin allocation failed.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20090805200931.GB5319@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Instead of plain NULL deref we better throw error
message with a backtrace. Actually we need more
gracious error handling here. Meanwhile leave it
as is.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
LKML-Reference: <20090801075435.769301745@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This allow us to save a few lines of code.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
LKML-Reference: <20090801075435.597863129@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In uv_setup_irq(), the call to create_irq() initially assigns
IRQ vectors to cpu 0. The subsequent call to
assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to
another cpu and frees the cpu 0 vector - at least it will be
freed as soon as the "IRQ move" completes.
arch_enable_uv_irq() needs to send a cleanup IPI to complete
the IRQ move. Otherwise, assignment of GRU interrupts on large
systems (>200 cpus) will exhaust the cpu 0 interrupt vectors
and initialization of the GRU driver will fail.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090720142840.GA8885@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This takes care of the following entry from Dan's list:
arch/x86/kernel/apic/io_apic.c +3241 destroy_irq(11) warning: variable derefenced before check 'desc'
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Cc: Julia Lawall <julia@diku.dk>
LKML-Reference: <200907302321.19086.bzolnier@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The 32 and 64-bit versions of ioapic_retrigger_irq() are identical
except the 64-bit one takes vector_lock. vector_lock is defined and
used on 32-bit too, so just use a common ioapic_retrigger_irq().
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
There's no need for a control variable in replace_pin_at_irq_node();
it can just return if it finds the old apic/pin to replace.
If the loop terminates, then it didn't find the old apic/pin, so it can
add the new ones.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Rather than duplicating the same alloc/init code twice, restructure
the function to look for duplicates and then add an entry
if none is found.
This function is not performance critical; all but one of its callers
are __init functions, and the non-__init caller is for PCI device setup.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Convert the unconventional loop in io_apic_level_ack_pending() to
a conventional for() loop.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The comment got separated from its subject, so move it to what
appears to be the right place, and update to describe the current
structure.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The structure is defined immediately below, so there's no need
to forward declare it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
While no 64-bit hardware will have a version 0x11 I/O APIC which needs
the level/edge bug workaround, that's not a particular reason to use
CONFIG_X86_32 to #ifdef the code out. Most 32-bit machines will no
longer need the workaround either, so the test to see whether it is
necessary should be more fine-grained than "32-bit=yes, 64-bit=no".
(Also fix formatting of block comment.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The main difference between 32 and 64-bit __mask_IO_APIC_irq() does a
readback from the I/O APIC to synchronize it.
If there's a hardware requirement to do a readback sync after updating
an APIC register, then it will be a hardware requrement regardless of
whether the kernel is compiled 32 or 64-bit.
Unify __mask_IO_APIC_irq() using the 64-bit version which always syncs
with io_apic_sync().
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If ioapic_modify_irq() is marked inline, it gets inlined several times.
Un-inlining it saves around 200 bytes in .text for me.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Stephen reported that his DL585 G2 needed noapic after 2.6.22 (?)
Dann bisected it down to:
commit 30a18d6c3f
Date: Tue Feb 19 03:21:20 2008 -0800
x86: multi pci root bus with different io resource range, on
64-bit
It turns out that:
1. that AMD-based systems have two HT chains.
2. BIOS doesn't allocate resources for BAR 6 of devices under 8132 etc
3. that multi-peer-root patch will try to split root resources to peer
root resources according to PCI conf of NB
4. PCI core assigns unassigned resources, but they overlap with BARs
that are used by ioapic addr of io4 and 8132.
The reason: at that point ioapic address are not inserted yet. Solution
is to insert ioapic resources into the tree a bit earlier.
Reported-by: Stephen Frost <sfrost@snowman.net>
Reported-and-Tested-by: dann frazier <dannf@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@jbarnes-g45.(none)>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.
This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.
Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
