Pull i2c bugfixes from Wolfram Sang:
"These should have been in rc2 but I missed it due to working on devm
longer than expected.
There is one ID addition, since we are touching the driver anyhow.
And the feature bit documentation is one outcome of a debug session
and will make it easier for users to work around problems. The rest
is typical driver bugfixes."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: suppress lockdep warning on delete_device
i2c: mv64xxx: work around signals causing I2C transactions to be aborted
i2c: i801: Document feature bits in modinfo
i2c: designware: add Intel BayTrail ACPI ID
i2c: designware: always clear interrupts before enabling them
i2c: designware: fix RX FIFO overrun
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Barry Song <Baohua.Song@csr.com>
Do not use interruptible waits in an I2C driver; if a process uses
signals (eg, Xorg uses SIGALRM and SIGPIPE) then these signals can
cause the I2C driver to abort a transaction in progress by another
driver, which can cause that driver to fail. I2C drivers are not
expected to abort transactions on signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Duplicate the feature bits documentation in modinfo, as not every user
will read the driver's source code or documentation file.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is the same controller as on Intel Lynxpoint but the ACPI ID is
different (8086F41). Add support for this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the I2C bus is put to a low power state by an ACPI method it might pull
the SDA line low (as its power is removed). Once the bus is put to full
power state again, the SDA line is pulled back to high. This transition
looks like a STOP condition from the controller point-of-view which sets
STOP detected bit in its status register causing the driver to fail
subsequent transfers.
Fix this by always clearing all interrupts before we start a transfer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
i2c_dw_xfer_msg() pushes a number of bytes to transmit/receive
to/from the bus into the TX FIFO.
For master-rx transactions, the maximum amount of data that can be
received is calculated depending solely on TX and RX FIFO load.
This is racy - TX FIFO may contain master-rx data yet to be
processed, which will eventually land into the RX FIFO. This
data is not taken into account and the function may request more
data than the controller is actually capable of storing.
This patch ensures the driver takes into account the outstanding
master-rx data in TX FIFO to prevent RX FIFO overrun.
Signed-off-by: Josef Ahmad <josef.ahmad@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.
The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero. However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.
This patch changes the write access to the transmit FIFO to always be 16 bits
wide.
Signed off by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
I've been debugging the abnormal operation of i2c on octeon. If a process is
terminated by signal in the middle of i2c operation, next i2c read operation
which is done by another process was failed. So i changed to ignore signal in
the middle of i2c operation. After that the problem was not reproduced.
Signed-off-by: Eunbong Song <eunb.song@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Use generic DMA DT helper. Platforms booting with or without DT populated are
both supported.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In PIO mode we can end up with the same errors as in DMA mode, but as IRQs
are disabled there we have to check for them manually after each command.
Also don't use the big controller reset hammer when receiving a NAK from a
slave. It's sufficient to tell the controller to continue at a clean state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit fixes the three following races in PIO code:
- The CTRL0 register is racy in itself, when programming transfer state and
run bit in the same cycle the hardware sometimes ends up using the state
from the last transfer. Fix this by programming state in one cycle, make
sure the write is flushed down APBX bus by reading back the reg and only
then trigger the run bit.
- Only clear the DMAREQ bit in DEBUG0 after the read/write to the data reg
happened. Otherwise we are racing with the hardware about who touches
the data reg first.
- When checking for completion of a transfer it's not sufficient to check
if the data engine finished, but also a check for i2c bus idle is needed.
In PIO mode we are really fast to program the next transfer after a finished
one, so the controller possibly tries to start a new transfer while the
clkgen engine is still busy writing the NAK/STOP from the last transfer to
the bus.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using autosuspend helps to reduce the resume latency in situations where
another I2C message is going to be started soon. For example with HID over
I2C touch panels we get several messages in a short period of time while
the touch panel is in use.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is not an atomic context so there is no need to use mdelay() but
instead use usleep_range().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The correct way to disable or enable the controller is to wait until the
DW_IC_ENABLE_STATUS register bit matches the bit we program into DW_IC_ENABLE
register. This procedure is described in the DesignWare I2C databook.
By doing this we can be sure that the controller is in correct state once
the function returns.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is not good idea to mix static and dynamic I2C adapter numbering. In
this particular case on Lynxpoint we had graphics I2C adapter which took
the first numbers preventing the designware I2C driver from using the
adapter numbers it preferred.
Since Lynxpoint support was just introduced and there is no hardware available
outside Intel we can fix this by switching to use dynamic adapter numbering
instead of static.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With dev_err() we can get the device instance printed as well and is pretty
much standard to use dev_* macros in the drivers anyway. In addition
correct the indentation of probe() arguments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller and tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus read and write are supported by the emulation layer of i2c
framework if the controller doesn't have SMBus features.
I2C_M_RECV_LEN flag is used to let i2c drivers know rx length is not
yet determined but will be read to the first byte in rx buffer.
s3c2410 doesn't handle this flag. So only one byte is read from slave.
There fore following two features are added to the driver code.
1. skip rx length check if I2C_M_RECV_LEN is set and the length is 1.
2. add actual bytes to the rx length after reading first bytes if
I2C_M_RECV_LEN.
I2C_M_RECV_LEN is only set for SMBus command. So this code does not
affect legacy codes which only use i2c command for s3c2410.
Signed-off-by: Jaemin Yoo <jmin.yoo@samsung.com>
Tested-by: Prasanna Kumar <prasanna.ps@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
The ACPI handle of struct i2c_adapter's dev member should not be
set, because this causes that struct i2c_adapter to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct i2c_adapter). Consequently,
acpi_i2c_register_devices() should use the ACPI handle of the
parent of the struct i2c_adapter it is called for rather than the
struct i2c_adapter's ACPI handle (which should be NULL).
Make that happen and modify the i2c-designware-platdrv driver,
which currently is the only driver for ACPI-enumerated I2C
controller chips, not to set the ACPI handle for the
struct i2c_adapter it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the code to use devm_* API so that driver core will manage
resources.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since we have generic i2c bus recover routines now, these custom ones
need to be renamed to fix the namespace clash. Proper conversion needs
to be done by someone who has access to the hardware.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GPIOs may not be available immediately when i2c-gpio looks for them.
Implement support for deferred probing so that probing can be
attempted again later when GPIO pins are finally available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make them conform more to established standards.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The register definitions are only used in the driver itself.
This also removes the last dependency on plat/ includes from the
i2c driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Delete the header that defines it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit: "i2c-core: dt: Pick i2c bus number from i2c alias if
present" adds support for automatically picking the bus number based
on the alias ID. Remove the now unnecessary code from i2c-pxa that
did the same thing.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
This patch adds the iSMT SMBus Controller DeviceIDs for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Remove !S390 dependency from i2c Kconfig, since s390 now supports PCI, HAS_IOMEM
and HAS_DMA, however we need to add a couple of GENERIC_HARDIRQS dependecies to
fix compile and link errors like these:
ERROR: "devm_request_threaded_irq" [drivers/i2c/i2c-smbus.ko] undefined!
ERROR: "devm_request_threaded_irq" [drivers/i2c/busses/i2c-ocores.ko] undefined!
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Intel ismt & Broadcom bcm2835
- a number of drivers got support for more variants and mostly got
cleaned up on the way (sis630, i801, at91, tegra, designware)
- i2c got rid of all *_set_drvdata(..., NULL) on remove/probe failure
- removed the i2c_smbus_process_call from the core since there are no
users
- mxs can now switch between PIO and DMA depending on the message
size and the bus speed can now be arbitrary
In addition, there is the usual bunch of fixes, cleanups, devm_*
conversions, etc"
Fixed conflict (and buggy devm_* conversion) in i2c-s3c2410.c
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
i2c: pxa: remove incorrect __exit annotations
i2c: ocores: Fix pointer to integer cast warning
i2c: tegra: remove warning dump if timeout happen in transfer
i2c: fix i2c-ismt.c printk format warning
i2c: i801: Add Device IDs for Intel Wellsburg PCH
i2c: add bcm2835 driver
i2c: ismt: Add Seth and Myself as maintainers
i2c: sis630: checkpatch cleanup
i2c: sis630: display unsigned hex
i2c: sis630: use hex to constants for SMBus commands
i2c: sis630: fix behavior after collision
i2c: sis630: clear sticky bits
i2c: sis630: Add SIS964 support
i2c: isch: Add module parameter for backbone clock rate if divider is unset
i2c: at91: fix unsed variable warning when building with !CONFIG_OF
i2c: Adding support for Intel iSMT SMBus 2.0 host controller
i2c: sh_mobile: don't send a stop condition by default inside transfers
i2c: sh_mobile: eliminate an open-coded "goto" loop
i2c: sh_mobile: fix timeout error handling
...
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
There is simply no reason to be manually setting the private driver
data to NULL in the remove/fail to probe cases. This is just extra
cruft code that can be removed.
A few notes:
* Nothing relies on drvdata being set to NULL.
* The __device_release_driver() function eventually calls
dev_set_drvdata(dev, NULL) anyway, so there's no need to do it
twice.
* I verified that there were no cases where xxx_get_drvdata() was
being called in these drivers and checking for / relying on the NULL
return value.
This could be cleaned up kernel-wide but for now just take the baby
step and remove from the i2c subsystem.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
