Convert the state numbers, device state, etc from numbers to strings
when printing debug messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array msi_tgt_status is defined but never used, hence it is
redundant and can be removed.
Cleans up clang warning:
warning: 'msi_tgt_status' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The totally undocumented IO mode needs to be set to enumerator
0 to enable port 4 also known as WAN in most configurations,
for ordinary traffic. The 3 bits in the register come up as
010 after reset, but need to be set to 000.
The Realtek source code contains a name for these bits, but
no explanation of what the 8 different IO modes may be.
Set it to zero for the time being and drop a comment so
people know what is going on if they run into trouble. This
"mode zero" works fine with the D-Link DIR-685 with
RTL8366RB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ptr_ret.cocci warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum_flower.c:543:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to enable/disable supported chips in be2net.
With disable support are removed coresponding PCI IDs and
also codepaths with [BE2|BE3|BEx|lancer|skyhawk]_chip checks.
Disable chip will reduce module size by:
BE2 ~2kb
BE3 ~3kb
Lancer ~10kb
Skyhawk ~9kb
When enable skyhawk only it will reduce module size by ~20kb
New help style in Kconfig
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main motive of this patch is to lay down driver's
tc offload infrastructure in place.
With these changes tc can offload various supported flow
profiles (4 tuples, src-ip, dst-ip, l4 port) for the drop
action. Dropped flows statistic is a global counter for
all the offloaded flows for drop action and is populated
in ethtool statistics as common "gft_filter_drop".
Examples -
tc qdisc add dev p4p1 ingress
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_ip 192.168.40.200 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto udp src_ip 192.168.40.100 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp src_ip 192.168.40.100 dst_ip 192.168.40.200 \
src_port 453 dst_port 876 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_port 98 action drop
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for dropping and redirecting
the flows based on destination IP in the packet.
This also moves the profile mode settings in their own
functions which can be used through tc flows in successive
patch.
For example -
ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.40.100 action -1
ethtool -N p5p1 flow-type udp4 dst-ip 192.168.50.100 action 1
ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.60.100 action 0x100000000
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for tc mqprio offload,
using this different traffic classes on the adapter
can be utilized based on configured priority to tc map.
For example -
tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3
This will cause SKBs with priority 0,1,2,3 to transmit
over tc 0,1,2,3 hardware queues respectively.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the bindings parsing for XGMAC2 IP block.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have all the XGMAC related callbacks, lets start integrating
this IP block into main driver.
Also, we corrected the initialization flow to only start DMA after
setting descriptors length.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC2 uses the same engine of timestamping as GMAC4. Let's use the same
callbacks.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MDIO related funcionalities for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the descriptor related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DMA related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MAC related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new entry to HWIF table for XGMAC 2.10. For now we fill it with
empty callbacks which will be added in posterior patches.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port changes CMODE, the SERDES interface being used can change.
Disable interrupts for the old SERDES interface, and enable interrupts
on the new.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink wants to know when the MAC layers notices a change in the
link. For the 6390 family, this is a change in the SERDES state.
Add interrupt support for the SERDES interface used to implement
SGMII/1000Base-X/2500Base-X. This is currently limited to ports 9 and
10. Support for the 10G SERDES and other ports will be added later,
building on this basic framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An up coming change will register interrupts for individual switch
ports, using the mv88e6xxx_port as the interrupt context information.
Add members to the mv88e6xxx_port structure so we can link it back to
the mv88e6xxx_chip member the port belongs to and the port number of
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family has a number of SERDES interfaces per port. When the
cmode changes, eg 1000Base-X to XAUI, the SERDES interface in use will
also change. Power down the old SERDES interface and power up the new
SERDES interface.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ports CMODE indicates the type of link between the MAC and the
PHY. It is used often in the SERDES code. Rather than read it each
time, cache its value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 has three different SERDES interface types. 2500Base-X is
implemented by the SGMII/1000Base-X SERDES. So power on/off the
correct SERDES.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for accessing SERDES registers of the 6390 family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a need to add more functions manipulating the SERDES
interfaces. Cleanup the namespace.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 has two SERDES interfaces, used by ports 9 and 10. The 6390X
has eight SERDES interfaces. These allow ports 9 and 10 to do 10G. Or
if lower speeds are used, some of the SERDES interfaces can be used by
ports 2-8 for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family has 8 SERDES lanes. What ports use these lanes depends
on how ports 9 and 10 are configured. If 9 and 10 does not make use of
a line, one of the lower ports can use it.
Add a function to return the lane a port is using, if any, and simplify
the code to power up/down the lane.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rudimentary phylink support to mv88e6xxx.
TODO:
- needs to call phylink_mac_change() when the port link comes up/goes down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for MAC drivers to use in their validate callback to deal
with 2500BaseX vs 1000BaseX modes, where the hardware supports both
but it is not possible to automatically select between them.
This helper defaults to 1000BaseX, as that is the 802.3 standard, and
will allow users to select 2500BaseX either by forcing the speed if
AN is disabled, or by changing the advertising mask if AN is enabled.
Disabling AN is not recommended as it is only the speed that we're
interested in controlling, not the duplex or pause mode parameters.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6185 can enable/disable 802.3z pause be setting the MyPause bit in
the port status register. Add an op to support this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before MC-aware mode was enabled in commit 7b81953066 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"), only 8 traffic
classes were used. Under MC-aware regime, however, besides using TCs
0-7 for UC traffic, it additionally uses TCs 8-15 for BUM traffic. It
is therefore desirable to show counters for these TCs as well.
Update ethtool stats pool length, mlxsw_sp_port_get_strings() and
mlxsw_sp_port_get_stats() to include artifacts for all 16 TCs. For
consistency and simplicity, expose tc_no_buffer_discard_uc_tc for BUM
TCs as well, even though it ought to stay at 0 all the time.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_port_get_sset_count() is supposed to return the
total number of ethtool strings that mlxsw supports. Specifically for
names of statistic counters (the only string type that mlxsw supports
as of now), that number is stored in MLXSW_SP_PORT_ETHTOOL_STATS_LEN.
However, when adding RFC-2891 counters, that define wasn't updated to
include the new counters. As a result, ethtool snips out the counters
towards the end of the list, which contains per-TC counters, and only
the first three traffic classes end up being reported.
Fix by adding MLXSW_SP_PORT_HW_RFC_2819_STATS_LEN as appropriate.
Fixes: 1222d15a01 ("mlxsw: spectrum: Expose counters for various packet sizes")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent FW fixes a bug and allows to load newly flashed FW image after
reset. So make sure the reset happens after flash. Indicate the need
down to PCI layer by -EAGAIN.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware contains:
- Support for new types of cables
- Support for flashing future firmware without reboot
- Support for Router ARP BC and UC traps
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As recent spectrum FW imposes a limitation on using vlan_id key for
egress ACL, disallow the usage of that key accordingly and return a
proper extack message.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cond_resched() instead of usleep_range() to decrease the time
between polling attempts thus reducing overall driver load time.
Below is a comparison before and after the change, of loading eight
virtual functions.
Before:
real 0m8.785s
user 0m0.093s
sys 0m0.090s
After:
real 0m5.730s
user 0m0.097s
sys 0m0.087s
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_query_vport_state() and mlx5_modify_vport_admin_state() are used
only from within mlx5_core - unexport them.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_query_vport_admin_state() is not used anywhere. Remove it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused nvports argument.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify and query vport state commands share the same admin_state and
op_mod values, rename the enums to fit them both.
In addition, remove the esw prefix from the admin state enum as this
also applied for vnic.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware has defined new HCA capability field called "max_num_eqs",
that is the number of available EQs after subtracting reserved FW EQs.
Before this capability the FW reported the EQ number in "log_max_eqs",
the reported value also contained FW reserved EQs, but the driver might
be failing to load on 320 cpus systems due to the fact that FW
reserved EQs were not available to the driver.
Now the driver has to obtain max_num_eqs value from new FW to get real
number of EQs available.
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.
Fixes: b21f502f84 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused netdev_registered_init/remove in en.h
Return ENOSUPPORT if the check MLX5_DSCP_SUPPORTED fails.
Remove extra white space
Fixes: 2a5e7a1344 ("net/mlx5e: Add dcbnl dscp to priority support")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current check relies on function BDF addresses and can get
us wrong e.g when two VFs are assigned into a VM and the PCI
v-address is set by the hypervisor.
Fixes: 5c65c564c9 ('net/mlx5e: Support offloading TC NIC hairpin flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Alaa Hleihel <alaa@mellanox.com>
Tested-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function hwsim_add_one()
in the error handling case.
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value from kzalloc() is not checked correctly. The
test is done against a wrong variable. This patch fix it.
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing rcu_assign_pointer()/rcu_dereference() to used rcu
pointers. There was already a previous commit c5d99d2b35 ("ieee802154:
hwsim: fix rcu address annotation"), but there was more which was
pointed out on my side by using newest sparse version.
Cc: Stefan Schmidt <stefan@datenfreihafen.org>
Fixes: f25da51fdc ("ieee802154: hwsim: add replacement for fakelb")
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem below. The problem can be reproduced by the
following steps:
1) Connecting all HiNIC interfaces
2) On server side
# sudo ifconfig eth0 192.168.100.1 up #Using MLX CX4 card
# iperf -s
3) On client side
# sudo ifconfig eth0 192.168.100.2 up #Using our HiNIC card
# iperf -c 192.168.101.1 -P 10 -t 100000
after hours of testing, we will see errors:
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
The errors are caused by the following problem.
1) The hinic_get_wqe() checks the "wq->delta" to allocate new WQEs:
if (atomic_sub_return(num_wqebbs, &wq->delta) <= 0) {
atomic_add(num_wqebbs, &wq->delta);
return ERR_PTR(-EBUSY);
}
If the WQE occupies multiple pages, the shadow WQE will be used. Then the
hinic_xmit_frame() fills the WQE.
2) While in parallel with 1), the free_tx_poll() checks the "wq->delta"
to free old WQEs:
if ((atomic_read(&wq->delta) + num_wqebbs) > wq->q_depth)
return ERR_PTR(-EBUSY);
There is a probability that the shadow WQE which hinic_xmit_frame() is
using will be damaged by copy_wqe_to_shadow():
if (curr_pg != end_pg) {
void *shadow_addr = &wq->shadow_wqe[curr_pg * wq->max_wqe_size];
copy_wqe_to_shadow(wq, shadow_addr, num_wqebbs, *cons_idx);
return shadow_addr;
}
This can cause WQE data error and you will see the above error messages.
This patch fixes the problem.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
