Clean up OMAP GPIO request/free functions
- Rename and declare static OMAP specific GPIO request/free functions
- Register them into gpiolib as chip-specific hooks
- Add omap_request_gpio/omap_free_gpio wrappers for existing code not
converted yet to use gpiolib
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
[ dbrownell@users.sourceforge.net: remove needless check_gpio() calls ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.
(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More conversion to the standard GPIO interfaces: stop using
omap_set_gpio_direction() entirely, and switch over to the
gpio_direction_output() call.
Note that because gpio_direction_output() includes the initial
value, this change isn't quite transparent.
- For the call sites which defined an initial value either
before or after setting the direction, that value was used.
When that value was previously assigned afterwards, this
could eliminate a brief output glitch ... and possibly
change behavior. In a few cases (LCDs) several values
were assigned together ... those were re-arranged to match
the explicit sequence provided.
- Some call sites didn't define such a value; so I chose an
initial "off/reset" value that seemed to default to "off".
In short, files touched by this patch might notice some small
changes in startup behavior (with trivial fixes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make OMAP use the new __gpio_to_irq() hook, to make it easier to
support IRQs coming in from off-chip gpio controllers like the
TWL4030/TPS65930 chip used on OMAP3 boads like Beagleboard.org and
the Gumstix Overo.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are already various drivers having bigger label than 10 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes gpio "driver" to enable debounce clock for
gpio-bank only when debounce is enabled for some gpio in that bank.
Gpio functional clocks are also renamed in clock tree, gpioX_fck ->
gpioX_dbck.
This patch triggers problem with gpio wake-up and Omap3. Gpios in PER
domain aren't capable to generate wake-up if PER domain is in sleep
state. For this iopad wake-up should be used and needed pad
configuration should be done. Enabling iopad wake-up for gpio pads is
left for bootloader or omap mux configuration in kernel.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Give the correct size when reserving the interrupt vector table. It should be
a page not a single byte.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the preemption resume_kernel() routine by inverting the test to see
whether interrupts are off (IM7 is all enabled, not all disabled).
Furthermore, interrupts should be disabled on entry to resume_kernel() so that
they're correctly set for jumping to restore_all() and doing the need
reschedule test.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Discard low-prioriy Tx interrupts when closing an MN10300 on-chip serial port.
The MN10300 on-chip serial port uses three interrupts to manage its serial
ports:
(1) A very high priority interrupt that drives virtual DMA for Rx.
(2) A very high priority interrupt that drives virtual DMA for Tx.
(3) A normal priority virtual interrupt that does the normal UART interrupt
stuff and is shared between Rx and Tx.
mn10300_serial_stop_tx() only disables the high priority Tx interrupt. It
doesn't also disable the normal priority one because it is shared with Rx.
However, the high priority interrupt may interrupt local_irq_disabled()
sections, and so may have queued up a low priority virtual interrupt whilst the
UART driver is asking for the Tx interrupt to be disabled.
The result of this can be an oops when we try to process the interrupt in
mn10300_serial_transmit_interrupt() as port->uart.info and port->uart.info->tty
may have gone away.
To deal with this, if either of those pointers is NULL, we make sure the
high-priority Tx interrupt is disabled and discard the interrupt. The low
priority interrupt is disabled by the mn10300_serial_pic irq_chip table.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include the linux/page.h header into the MN10300 kernel linker script thus
allowing us to use PAGE_SIZE macro instead of a numeric constant.
Also use the PERCPU macro instead of an explicit section definition.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] SN: prevent IRQ retargetting in request_irq()
[IA64] Fix section mismatch ioc3uart_init()/ioc3uart_submodule
[IA64] Clear up section mismatch for ioc4_ide_attach_one.
[IA64] Clear up section mismatch with arch_unregister_cpu()
[IA64] Clear up section mismatch for sn_check_wars.
[IA64] Updated the generic_defconfig to work with the 2.6.28-rc7 kernel.
[IA64] Fix GRU compile error w/o CONFIG_HUGETLB_PAGE
[IA64] eliminate NULL test and memset after alloc_bootmem
[IA64] remove BUILD_BUG_ON from paravirt_getreg()
mconsole_init() passed 256 bytes as length in os_create_unix_socket, while
the sizeof UNIX_PATH_MAX is 108. This patch fixes that problem and avoids
a big overrun bug reported on UML bootup.
sockaddr_un.sun_path is UNIX_PATH_MAX long which causes the problem.
Reported-by: Vikas K Managutte <vikki.km@gmail.com>
Reported-by: Sarvesh Kumar Lal Das <skldas@gmail.com>
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: WANG Cong <wangcong@zeuux.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org> [please check with Jeff]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented. This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.
Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the introduction of the generic affinity autoselector,
irq_select_affinity(), IRQs are now being retargetted,
using a default mask, via the request_irq() path.
This results in all IRQs targetted at CPU 0.
SN Altix assigns affinity in the SN PROM, and does not
expect that to be changed as part of request_irq().
Set the IRQ_AFFINITY_SET flag to prevent
request_irq() from resetting affinity.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The generic_defconfig has three section mismatches. This clears
arch_unregister_cpu()
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The generic_defconfig has three section mismatches. This clears up
sn_check_wars().
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The AUTOFS=y and AUTOFS4=y causes problems with some distros versions of
automount. I turned both of those to =m and then followed the default
prompts for everything else. I did notice that CONFIG_PNP_DEBUG got
changed to CONFIG_PNP_DEBUG_MESSAGES and the default was a =y so I turned
that back to a =n.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory. Thus a NULL test or memset after calls to these
functions is unnecessary.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
CC arch/ia64/kernel/asm-offsets.s
In file included from include/linux/bitops.h:17,
from include/linux/kernel.h:15,
from include/linux/sched.h:52,
from arch/ia64/kernel/asm-offsets.c:9:
arch/ia64/include/asm/bitops.h: In function 'set_bit':
arch/ia64/include/asm/bitops.h:47: error: implicit declaration of function 'BUILD_BUG_ON'
Obvious inclusion of kernel.h doesn't fix it, because of circular dependencies
involving fls.h and log2(). Fixing the latter requires some serious header surgery,
it seems, so just remove BUILD_BUG_ON for now.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] Fix alignment fault handling for ARMv6 and later CPUs
[ARM] 5340/1: fix stack placement after noexecstack changes
[ARM] 5339/1: fix __fls() on ARM
[ARM] Orion: fix bug in pcie configuration cycle function field mask
[ARM] omap: fix a pile of issues
these warnings:
arch/x86/kernel/paravirt-spinlocks.c: In function ‘default_spin_lock_flags’:
arch/x86/kernel/paravirt-spinlocks.c:12: warning: passing argument 1 of ‘__raw_spin_lock’ from incompatible pointer type
arch/x86/kernel/paravirt-spinlocks.c: At top level:
arch/x86/kernel/paravirt-spinlocks.c:11: warning: ‘default_spin_lock_flags’ defined but not used
showed that the prototype of default_spin_lock_flags() was confused about
what type spinlocks have.
the proper type on UP is raw_spinlock_t.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On ARMv6 and later CPUs, it is possible for userspace processes to
get stuck on a misaligned load or store due to the "ignore fault"
setting; unlike previous CPUs, retrying the instruction without
the 'A' bit set does not always cause the load to succeed.
We have no real option but to default to fixing up alignment faults
on these CPUs, and having the CPU fix up those misaligned accesses
which it can.
Reported-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 8ec53663d2 ("[ARM] Improve
non-executable support") added support for detecting non-executable
stack binaries. One of the things it does is to make READ_IMPLIES_EXEC
be set in ->personality if we are running on a CPU that doesn't support
the XN ("Execute Never") page table bit or if we are running a binary
that needs an executable stack.
This exposed a latent bug in ARM's asm/processor.h due to which we'll
end up placing the stack at a very low address, where it will bump into
the heap on any application that uses significant amount of stack or
heap or both, causing many interesting crashes.
Fix this by testing the ADDR_LIMIT_32BIT bit in ->personality instead
of testing for equality against PER_LINUX_32BIT.
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 440x5 core in the Virtex5 uses the 440A type machine check
(ie, they have MCSRR0/MCSRR1). They thus need to call the
appropriate fixup function to hook the right variant of the
exception.
Without this, all machine checks become fatal due to loss
of context when entering the exception handler.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Sync FPU state in VIS emulation handler.
sparc64: Fix VIS emulation bugs
sparc: asm/bitops.h should define __fls
sparc64: Fix bug in PTRACE_SETFPREGS64 handling.
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix early panic with boot option "nosmp"
x86/oprofile: fix Intel cpu family 6 detection
oprofile: fix CPU unplug panic in ppro_stop()
AMD IOMMU: fix possible race while accessing iommu->need_sync
AMD IOMMU: set device table entry for aliased devices
AMD IOMMU: struct amd_iommu remove padding on 64 bit
x86: fix broken flushing in GART nofullflush path
x86: fix dma_mapping_error for 32bit x86
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Return ENOSYS from sys32_syscall on 64bit kernels like elsewhere.
MIPS: 64-bit: vmsplice needs to use the compat wrapper for o32 and N32.
MIPS: o32: Fix number of arguments to splice(2).
MIPS: Malta: Consolidate platform device code.
MIPS: IP22, Fulong, Malta: Update defconfigs.
MIPS: Malta: Add back RTC support
MIPS: Fix potential DOS by untrusted user app.
This is needed so that Vitesse 7385 5-port switch could work on
MPC8349E-mITX boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When the o32 errno was changed to ENOSYS, we forgot to update the code
for 64bit kernels.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The syscall code was assuming splice only takes 4 arguments so no stack
arguments were being copied from the userspace stack to the kernel stack.
As the result splice was likely to fail with EINVAL.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These haven't seen much attention for too long but particularly important
enable RTC_CLASS and CONFIG_RTC_HCTOSYS so the wall clock time is set on
kernel startup.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the conversion of MIPS to RTC_LIB the old RTC driver CONFIG_RTC became
unselectable. Fix by setting up a platform device. Also enable
RTC_CLASS so system time gets set from RTC on kernel initialization.
[Ralf: Original patch by Tiejun; polished nice and shiny by me]
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a 64 bit kernel if an o32 syscall was made with a syscall number less
than 4000, we would read the function from outside of the bounds of the
syscall table. This led to non-deterministic behavior including system
crashes.
While we were at it we reworked the 32 bit version as well to use fewer
instructions. Both 32 and 64 bit versions are use the same code now.
Signed-off-by: Vlad Malov <Vlad.Malov@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Copy the FPU state to the task's thread_info->fpregs for the VIS emulation
functions to access.
Signed-off-by: Hong H. Pham <hong.pham@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: fix boot crash with numcpus=0 on certain systems
Fix early exception in __get_smp_config with nosmp.
Bail out early when there is no MP table.
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
