The current code already forwards the VF MAC address to the PF, except
in one case. If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address. This
causes "ip link show" to show zero VF MAC addresses for this case.
This assumption is not correct. Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe. So we need to always forward the VF MAC address to the PF.
The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.
Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only non-NPAR PFs need to actively check and manage unsupported link
speeds. NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression. With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.
Increase the maximum wait time from 5 usec to 20 usec. Also, fix
the debug message that shows the total delay time for the response
when the message times out. With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic to reserve default rings at driver open time if none was
reserved during probe time. This will happen when the PF driver did
not provision minimum rings to the VF, due to more limited resources.
Driver open will only succeed if some minimum rings can be reserved.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For completeness and correctness, the VF driver needs to reserve these
RSS and L2 contexts.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rings are more limited and the PF has not provisioned minimum
guaranteed rings to the VF, do not reserve rings during driver probe.
Wait till device open before reserving rings when they will be used.
Device open will succeed if some minimum rings can be successfully
reserved and allocated.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not reserve rings during ethtool -L when the device
is down. The rings will be reserved when the device is later opened.
Change it to reserve rings during ethtool -L when the device is down.
This provides a better guarantee that the device open will be successful
when the rings are reserved ahead of time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds debugfs support for bnxt_en with the purpose of allowing users
to examine the current DIM profile in use for each receive queue. This
was instrumental in debugging issues found with DIM and ensuring that
the profiles we expect to use are the profiles being used.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing with DIM enabled on older kernels indicated that firmware calls
were slower than expected. More detailed analysis indicated that the
default 25us delay was higher than necessary. Reducing the time spend in
usleep_range() for the first several calls would reduce the overall
latency of firmware calls on newer Intel processors.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This keeps the RING_IDLE flag set in hardware for higher coalesce
settings by default and improved latency.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware does not allow the operation and would return failure, causing
a warning in dmesg. So check for VF and disallow it in the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add counters to display sum of rx/tx_discard_pkts of all rings as
function level statistics via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace switch statements printing different messages for every ring type
with a common message.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older firmware will reject this call and cause an error message to
be printed by the VF driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware messages that are forwarded from PF to VFs are encapsulated.
The size of these encapsulated messages must not exceed the maximum
defined message size. Add appropriate checks to avoid oversize
messages. Firmware messages may be expanded in future specs and
this will provide some guardrails to avoid data corruption.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially, the MQPRIO TCs are mapped 1:1 directly to the hardware
queues. Some of these hardware queues are configured to be lossless.
When PFC is enabled on one of more TCs, we now need to remap the
TCs that have PFC enabled to the lossless hardware queues.
After remapping, we need to close and open the NIC for the new
mapping to take effect. We also need to reprogram all ETS parameters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver maps MQPRIO traffic classes directly 1:1 to the
internal hardware queues (TC0 maps to hardware queue 0, etc). This
direct mapping requires the internal hardware queues to be reconfigured
from lossless to lossy and vice versa when necessary. This
involves reconfiguring internal buffer thresholds which is
disruptive and not always reliable.
Implement a new scheme to map TCs to internal hardware queues by
matching up their PFC requirements. This will eliminate the need
to reconfigure a hardware queue internal buffers at run time. After
remapping, the NIC is closed and opened for the new TC to hardware
queues to take effect.
This patch only adds the basic mapping logic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for introducing adaptive TX to net DIM.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver. This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.
Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096. Move the kzalloc() call
into the bnxt_get_pkgver() function.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
w/ bpf_xdp_adjust_tail helper xdp's data_end pointer could be changed as
well (only "decrease" of pointer's location is going to be supported).
changing of this pointer will change packet's size.
for bnxt driver we will just calculate packet's length unconditionally
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When open fails during ethtool -L ring change, for example, the driver
may crash at bnxt_free_irq() because bp->bnapi is NULL.
If we fail to allocate all the new rings, bnxt_open_nic() will free
all the memory including bp->bnapi. Subsequent call to bnxt_close_nic()
will try to dereference bp->bnapi in bnxt_free_irq().
Fix it by checking for !bp->bnapi in bnxt_free_irq().
Fixes: e5811b8c09 ("bnxt_en: Add IRQ remapping logic.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With recent changes to reserve both L2 and RDMA rings, we need to include
the RDMA rings in bnxt_check_rings(). Otherwise we will under-estimate
the rings we need during ethtool -L and may lead to failure.
Fixes: fbcfc8e467 ("bnxt_en: Reserve completion rings and MSIX for bnxt_re RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While a VF is configured with a bigger mtu (> 1500), any packets that
are punted to the VF-rep (slow-path) get dropped by OVS kernel-datapath
with the following message: "dropped over-mtu packet". Fix this by
returning the max-mtu value for a VF-rep derived from its corresponding VF.
VF-rep's mtu can be changed using 'ip' command as shown in this example:
$ ip link set bnxt0_pf0vf0 mtu 9000
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently uses src port field (along with other fields) in the
decap tunnel key, while looking up and adding tunnel nodes. This leads to
redundant cfa_decap_filter_alloc() requests to the FW and flow-miss in the
flow engine. Fix this by ignoring the src port field in decap tunnel nodes.
Fixes: f484f6782e ("bnxt_en: add hwrm FW cmds for cfa_encap_record and decap_filter")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the following commands would succeed as far as the
user was concerned:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol all \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01/44 action drop
The current flow offload infrastructure used does not support wildcard
matching for ethernet headers, so do not allow the second or third
commands to succeed. If a user wants to drop traffic on that interface
the protocol and MAC addresses need to be specified explicitly:
$ tc qdisc add dev p1p1 ingress
$ tc filter add dev p1p1 parent ffff: protocol arp \
flower skip_sw action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw action drop
...
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:01 action drop
$ tc filter add dev p1p1 parent ffff: protocol ipv4 \
flower skip_sw src_mac 00:02:00:00:00:02 action drop
...
There are also checks for VLAN parameters in this patch as other callers
may wildcard those parameters even if tc does not. Using different
flow infrastructure could allow this to work in the future for L2 flows,
but for now it does not.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ethtool .get_rxfh() crash by checking for valid indirection table
address before copying the data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver needs to re-initailize the IRQ vectors, we make the
new ulp_irq_stop() call to tell the RDMA driver to disable and free
the IRQ vectors. After IRQ vectors have been re-initailized, we
make the ulp_irq_restart() call to tell the RDMA driver that
IRQs can be restarted.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional logic to reserve completion rings for the bnxt_re driver
when it requests MSIX vectors. The function bnxt_cp_rings_in_use()
will return the total number of completion rings used by both drivers
that need to be reserved. If the network interface in up, we will
close and open the NIC to reserve the new set of completion rings and
re-initialize the vectors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor bnxt_need_reserve_rings() slightly so that __bnxt_reserve_rings()
can call it and remove some duplicated code.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add remapping logic so that bnxt_en can use any arbitrary MSIX vectors.
This will allow the driver to reserve one range of MSIX vectors to be
used by both bnxt_en and bnxt_re. bnxt_en can now skip over the MSIX
vectors used by bnxt_re.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, the range of MSIX vectors allocated for the RDMA
driver is disjoint from the network driver. This creates a problem
for the new firmware ring reservation scheme. The new scheme requires
the reserved completion rings/MSIX vectors to be in a contiguous
range.
Change the logic to allocate RDMA MSIX vectors to be contiguous with
the vectors used by bnxt_en on new firmware using the new scheme.
The new function bnxt_get_num_msix() calculates the exact number of
vectors needed by both drivers.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver code makes some assumptions about the group index
and the map index of rings. This makes the code more difficult to
understand and less flexible.
Improve it by adding the grp_idx and map_idx fields explicitly to the
bnxt_ring_struct as a union. The grp_idx is initialized for each tx ring
and rx agg ring during init. time. We do the same for the map_idx for
each cmpl ring.
The grp_idx ties the tx ring to the ring group. The map_idx is the
doorbell index of the ring. With this new infrastructure, we can change
the ring index mapping scheme easily in the future.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When firmware sends a DMA response to the driver, the last byte of the
message will be set to 1 to indicate that the whole response is valid.
The driver waits for the message to be valid before reading the message.
The firmware spec allows these response messages to increase in
length by adding new fields to the end of these messages. The
older spec's valid location may become a new field in a newer
spec. To guarantee compatibility, the driver should zero the valid
byte before interpreting the entire message so that any new fields not
implemented by the older spec will be read as zero.
For messages that are forwarded to VFs, we need to set the length
and re-instate the valid bit so the VF will see the valid response.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are created, the current code subtracts the maximum VF
resources from the PF's pool. This under-estimates the resources
remaining in the PF pool. Instead, we should subtract the minimum
VF resources. The VF minimum resources are guaranteed to the VFs
and only these should be subtracted from the PF's pool.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for the maximum pre-set TX channels for ethtool -l, we
need to check the current max_tx_scheduler_inputs parameter from firmware.
This parameter specifies the max input for the internal QoS nodes currently
available to this function. The function's TX rings will be capped by this
parameter. By adding this logic, we provide a more accurate pre-set max
TX channels to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather periodic extended port statistics, if the device is PF and
link is up.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include additional hardware port statistics in ethtool -S, which
are useful for debugging.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trusted VFs are allowed to modify MAC address, even when PF
has assigned one.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear flags when reset command processed successfully for components
specified.
Fixes: 6502ad5963 ("bnxt_en: Add ETH_RESET_AP support")
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RDMA driver is registered, use a new VNIC mode that allows
RDMA traffic to be seen on the netdev in promiscuous mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default ring logic to select default number of rings to be up to
8 per port if the default rings x NIC ports <= total CPUs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor changes, such as new extended port statistics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code includes wmb() followed by writel(). writel() already has a barrier on
some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Create a new wrapper function with relaxed write operator. Use the new
wrapper when a write is following a wmb().
Since code already has an explicit barrier call, changing writel() to
writel_relaxed().
Also add mmiowb() so that write code doesn't move outside of scope.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization, if we encounter errors, there is a code path that
calls bnxt_hwrm_vnic_set_tpa() with invalid VNIC ID. This may cause a
warning in firmware logs.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_restore_pf_fw_resources routine frees PF resources by calling
close_nic and allocates the resources back, by doing open_nic. However,
this is not needed, if the PF is already in closed state.
This bug causes the driver to call open the device and call request_irq()
when it is not needed. Ultimately, pci_disable_msix() will crash
when bnxt_en is unloaded.
This patch fixes the problem by skipping __bnxt_close_nic and
__bnxt_open_nic inside bnxt_restore_pf_fw_resources routine, if the
interface is not running.
Fixes: 80fcaf46c0 ("bnxt_en: Restore MSIX after disabling SRIOV.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, internal error value is returned by the driver, when
hwrm_cfa_flow_alloc() fails due lack of resources. We should be returning
Linux errno value -ENOSPC instead.
This patch also converts other similar command errors to standard Linux errno
code (-EIO) in bnxt_tc.c
Fixes: db1d36a273 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes added the bnxt_init_int_mode() call in the driver's open
path whenever ring reservations are changed. This call was previously
only called in the probe path. In the open path, if MQPRIO TC has been
setup, the bnxt_init_int_mode() call would reset and mess up the MQPRIO
per TC rings.
Fix it by not re-initilizing bp->tx_nr_rings_per_tc in
bnxt_init_int_mode(). Instead, initialize it in the probe path only
after the bnxt_init_int_mode() call.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a packet with VLAN tag, pass the entire 16-bit TCI to the
stack when calling __vlan_hwaccel_put_tag(). The current code is only
passing the 12-bit tag and it is missing the priority bits.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
