This reverts commit af14cca162.
This patch contains a race condition between packets and ctnetlink
in the conntrack addition. A new patch to fix this issue follows up.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
From: Ben Hutchings <ben@decadent.org.uk>
Extended VBLKs (those larger than the preset VBLK size) are divided
into fragments, each with its own VBLK header. Our LDM implementation
generally assumes that each VBLK is contiguous in memory, so these
fragments must be assembled before further processing.
Currently the reassembly seems to be done quite wrongly - no VBLK
header is copied into the contiguous buffer, and the length of the
header is subtracted twice from each fragment. Also the total
length of the reassembled VBLK is calculated incorrectly.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
This patch fixes a regression that was introduced by
commit 0a5f384677
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
This patch reverts commit 0a5f384677
and instead issues warnings only if cpdma_chan_submit returns -ENOMEM.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Hegde, Vinay <vinay.hegde@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/arm/mach-shmobile/board-ag5evm.c: included 'linux/dma-mapping.h'
twice, remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the bit field width information for the IPSR4 register
in the r8a7779 pin function controller (PFC).
Without this fix the Marzen board fails to receive data
over the serial console due to misconfigured pin function
for the RX pin.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the sh73a0 SMP code to use 32-bit PSTR access.
This fixes wakeup from deep sleep for sh73a0 secondary CPUs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The latest sh_eth driver needs a resource of TSU in the channel 1,
if the controller has TSU registers. So, this patch adds the resource.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This has been obsolescent for a while; time for the final push.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Correct spelling "erorr" to "error" in
arch/sh/drivers/pci/pci-sh7780.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Even if the documentation calls this bit "Reserved" it has to be set
to 0 for correct modesetting on IGA1.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
With kernel 3.1, Christoph removed i_alloc_sem and replaced it with
calls (namely inode_dio_wait() and inode_dio_done()) which are
EXPORT_SYMBOL_GPL() thus they cannot be used by non-GPL file systems and
further inode_dio_wait() was pushed from notify_change() into the file
system ->setattr() method but no non-GPL file system can make this call.
That means non-GPL file systems cannot exist any more unless they do not
use any VFS functionality related to reading/writing as far as I can
tell or at least as long as they want to implement direct i/o.
Both Linus and Al (and others) have said on LKML that this breakage of
the VFS API should not have happened and that the change was simply
missed as it was not documented in the change logs of the patches that
did those changes.
This patch changes the two function exports in question to be
EXPORT_SYMBOL() thus restoring the VFS API as it used to be - accessible
for all modules.
Christoph, who introduced the two functions and exported them GPL-only
is CC-ed on this patch to give him the opportunity to object to the
symbols being changed in this manner if he did indeed intend them to be
GPL-only and does not want them to become available to all modules.
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
CC: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A fix from Jesper Juhl removes an assignment in an ASSERT when a compare
is intended. Two fixes from Mitsuo Hayasaka address off-by-ones in XFS
quota enforcement.
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: make inode quota check more general
xfs: change available ranges of softlimit and hardlimit in quota check
XFS: xfs_trans_add_item() - don't assign in ASSERT() when compare is intended
This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niccolo Belli reported ipsec crashes in case we handle a frame without
mac header (atm in his case)
Before copying mac header, better make sure it is present.
Bugzilla reference: https://bugzilla.kernel.org/show_bug.cgi?id=42809
Reported-by: Niccolò Belli <darkbasic@linuxsystems.it>
Tested-by: Niccolò Belli <darkbasic@linuxsystems.it>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BenH says:
'Here are a few more powerpc bits for you. A stupid regression I
introduced with my previous commit to "fix" program check exceptions
(brown paper bag for me), fix the cpuidle default, a bug fix for
something that isn't strictly speaking a regression but some upstream
changes causes it to show in lockdep now while it didn't before, and
finally a trivial one for rusty to make his life easier later on
removing the old cpumask cruft. '
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix various issues with return to userspace
cpuidle: Default y on powerpc pSeries
powerpc: Fix program check handling when lockdep is enabled
powerpc: Remove references to cpu_*_map
Fix this:
arch/arm/mach-omap2/mailbox.c: In function 'omap2_mbox_probe':
arch/arm/mach-omap2/mailbox.c:354: error: 'omap2_mboxes' undeclared (first use in this function)
arch/arm/mach-omap2/mailbox.c:354: error: (Each undeclared identifier is reported only once
arch/arm/mach-omap2/mailbox.c:354: error: for each function it appears in.)
Which happens on CONFIG_ARCH_OMAP2 && !CONFIG_SOC_OMAP2420, due to
missing omap2_mboxes declaration.
In addition, make sure we declare the right mailbox instances for 2430.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes smsc911x support on platforms using gpmc_smsc911x_init().
Commit c7e963f688 (net/smsc911x: Add regulator support) added
the requirement that platforms provide vdd33a and vddvario supplies.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to i.MX27 Reference Manual (p 1593) TXBIT0 bit selects
whether the most significant or the less significant part of the
data word written to the FIFO is transmitted.
As DSP_A is the same as DSP_B with a data offset of 1 bit, it
doesn't make any sense to remove TXBIT0 bit here.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When setting overlay position with x<0, it will divide 0 and make drm
driver crash.
Signed-off-by: Hai Lan <hai.lan@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Booted my i965 machine and it started printing the unsupported pixel
format of 0 message (once I added content to it).
Oh looksie here, we pass 0. fix.
v2: compile it.
Buzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45966
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When doing IO with large amounts of data fragmentation, the global block
reserve calulations are too low. This increases them to avoid
ENOSPC crashes.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If btrfs reads a block and finds a parent transid mismatch, it clears
the uptodate flags on the extent buffer, and the pages inside it. But
we only clear the uptodate bits in the state tree if the block straddles
more than one page.
This is from an old optimization from to reduce contention on the extent
state tree. But it is buggy because the code that retries a read from
a different copy of the block is going to find the uptodate state bits
set and skip the IO.
The end result of the bug is that we'll never actually read the good
copy (if there is one).
The fix here is to always clear the uptodate state bits, which is safe
because this code is only called when the parent transid fails.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When we are setting up the mount, we close all the
devices that were not actually part of the metadata we found.
But, we don't make sure that one of those devices wasn't
fs_devices->latest_bdev, which means we can do a use after free
on the one we closed.
This updates latest_bdev as it goes.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This allows us to gracefully continue if we aren't able to insert
directory items, both for normal files/dirs and snapshots.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Recent enhancements in the bias management means that we might not be
in standby when the CODEC is idle and can have active widgets without
being in full power mode but the shutdown functionality assumes these
things. Add checks for the bias level at each stage so that we don't
do transitions other than the ON->PREPARE->STANDBY->OFF ones that the
drivers are expecting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
An error while creating sysfs attribute files in the driver's probe function
results in an error abort, but already created files are not removed. This patch
fixes the problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Cc: Dirk Eibach <eibach@gdsys.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For DSS clock domain to transition from idle to active state. It's necessary
to enable the optional clock DSS_FCLK before we enable the module using the
MODULEMODE bits in the clock domain's CM_DSS_DSS_CLKCTRL register.
This sequence was not followed correctly for the 'dss_hdmi' hwmod and it led
to DSS clock domain not getting out of idle when pm_runtime_get_sync() was
called for hdmi's platform device.
Since the clock domain failed to change it's state to active, the hwmod code
disables any clocks it had enabled before for this hwmod. This led to the clock
'dss_48mhz_clk' gettind disabled.
When hdmi's runtime_resume() op is called, the call to dss_runtime_get()
correctly enables the DSS clock domain this time. However, the clock
'dss_48mhz_clk' is needed for HDMI's PHY to function correctly. Since it was
disabled previously, the driver fails when it tries to enable HDMI's PHY.
Fix this for now by ensuring that dss_runtime_get() is called before we call
pm_runtime_get_sync() for hdmi's platform device. A correct fix for later would
be to modify the DSS related hwmod's mainclks, and also some changes in how
opt clocks are handled in the DSS driver.
This fixes the issue of HDMI not working when it's the default display. The
issue is not seen if any other display is already enabled as the first display
would have correctly enabled the DSS clockdomain.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A number of new device ids, and a cleanup/fix for some of the option
device ids that shouldn't have been added in the first place.
There's also a few USB 3 fixes for problems that people have reported,
and a usb-storage bugfix to round it out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9FVQMACgkQMUfUDdst+ym7RgCeNfqK8Oi7U+9rdd2hGGIElxTE
6KgAnipmo5T5Wfls6sh0zPCv8Uh7K6Zb
=SXPd
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB bugfixes for 3.3-rc4
A number of new device ids, and a cleanup/fix for some of the option
device ids that shouldn't have been added in the first place.
There's also a few USB 3 fixes for problems that people have reported,
and a usb-storage bugfix to round it out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Added Kamstrup VID/PIDs to cp210x serial driver.
USB: Serial: ti_usb_3410_5052: Add Abbot Diabetes Care cable id
usb-storage: fix freezing of the scanning thread
xhci: Fix encoding for HS bulk/control NAK rate.
USB: Set hub depth after USB3 hub reset
USB: Fix handoff when BIOS disables host PCI device.
USB: option: cleanup zte 3g-dongle's pid in option.c
USB: Don't fail USB3 probe on missing legacy PCI IRQ.
xhci: Fix oops caused by more USB2 ports than USB3 ports.
USB: Remove duplicate USB 3.0 hub feature #defines.
In the current kernel implementation, the Logitech Harmony 900 remote
control is matched to the cdc_ether driver through the generic
USB_CDC_SUBCLASS_MDLM entry. However, this device appears to be of the
pseudo-MDLM (Belcarra) type, rather than the standard one. This patch
blacklists the Harmony 900 from the cdc_ether driver and whitelists it for
the pseudo-MDLM driver in zaurus.
Signed-off-by: Scott Talbert <talbert@techie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intent was to clear out the icount struct here, but we accidentally
clear stack memory instead. It probably will lead to a NULL dereference
right away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel, radeon, exynos fixes.
Intel: fixes a few Ivybridge hangs, along with fixing RC6 on SNB (still
not on, but at least allows for distros to patch it on easily).
radeon: oops reading some files in debugfs that weren't meant to appear,
a fix that touches a lot of files, so looks worse than it is, it fixes
an oops if a GPU reset fails and userspace keeps submitting more data,
along with a minor BIOS fix for newer boards.
exynos: a group of fixes for exynos, they've sent me a few more but
these were all I got through, and its no hw vanilla kernel users see a
lot off yet.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/atom: dpms bios scratch reg updates
drm/radeon/kms: properly set accel working flag and bailout when false
drm/radeon: Only create additional ring debugfs files on Cayman or newer.
drm/exynos: added postclose to release resource.
drm/exynos: removed exynos_drm_fbdev_recreate function.
drm/exynos: fixed page flip issue.
drm/exynos: added possible_clones setup function.
drm/exynos: removed pageflip_event_list init code when closed.
drm/exynos: changed priority of mixer layers.
drm/exynos: Fix typo in exynos_mixer.c
drm/i915: do not enable RC6p on Sandy Bridge
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
drm/i915: gen7: work around a system hang on IVB
drm/i915: gen7: Implement an L3 caching workaround.
drm/i915: gen7: implement rczunit workaround
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
CC: stable@kernel.org
Reported-by: Federico Quagliata <federico@quagliata.org>
Fixed-by: Federico Quagliata <federico@quagliata.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
