Patch includes changes to upgrade bfa driver version to 3.2.23.0 and use
firmware version 3.2.3.0
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As per the FCP specs, the timeout for issuing ABTS is 20 sec; not 21
sec. Hence setting the TOV to 20 sec.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Observed Auto mode in the HBA side while doing manual D-Port test on the
switch side. Mode is not passed to BFA from firmware when the test is
triggered by switch side. BFA just blindly using Auto mode.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch set fixes the issue of brocade management utility hang
(bcu/HCM) when faa attributes are queried from multiple application
threads. Hang was due to race between the threads and completion handler
corruption.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In direct attach mode, if port features like QoS/Trunk/FEC/CR are
enabled, driver can receive PLOGI from the target before firmware
notifies lport online to the driver. In case the lport is not yet online
and a PLOGI is received, send a reject to the peer port, instead of
dropping it on the floor.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch addresses the issue of port not being registered with SCSI
layer on bfa or firmware initialization failure and subsequently failure
in collecting driver traces for debugging port init failures. Also it
has minor changes related to bfad state machine clean up.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch includes change to enable firmware patch simplication
feature. This feature is targeted to address the requirement to have
independent patch release for firmware. Prior to 3.2.3, releasing a
patch fix for firmware requires changes to bfa, to use new firmware
images. But with these changes, if the new firmware is flashed on to the
HBA with brocade adapter management utilites, driver uses the new
firmware after checking the patch release byte in the firmware version.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bfa driver crash is observed while pushing the firmware on to chinook
quad port card due to uninitialized bfi_image_ct2 access which gets
initialized only for CT2 ASIC based cards after request_firmware().
For quard port chinook (CT2 ASIC based), bfi_image_ct2 is not getting
initialized as there is no check for chinook PCI device ID before
request_firmware and instead bfi_image_cb is initialized as it is the
default case for card type check.
This patch includes changes to read the right firmware for quad port chinook.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes a crash when tried setting symbolic name for an offline
vport through sysfs. Crash is due to uninitialized pointer lport->ns,
which gets initialized only on linkup (port online).
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use pcie_get_readrq()/pcie_set_readrq() to simplify code.
Jon Mason proposed a similar patch a couple years ago (see below).
[bhelgaas: validate pcie_max_read_reqsz, add pointer to Jon's patch]
Reference: http://lkml.kernel.org/r/1309191190-14670-1-git-send-email-jdmason@kudzu.us
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Anil Gurumurthy <agurumur@brocade.com>
Cc: Vijaya Mohan Guvva <vmohan@brocade.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
This patch updates the firmware to address the thermal notification issue
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch set is mostly driver updates (usf, zfcp, lpfc, mpt2sas,
megaraid_sas, bfa, ipr) and a few bug fixes. Also of note is that the
Buslogic driver has been rewritten to a better coding style and 64 bit support
added. We also removed the libsas limitation on 16 bytes for the command size
(currently no drivers make use of this).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJR0ugCAAoJEDeqqVYsXL0MX2sH+gOkWuy5p3igz+VEim8TNaOA
VV5EIxG1v7Q0ZiXCp/wcF6eqhgQkWvkrKSxWkaN0yzq8LEWfQeY7VmFDbGgFeVUZ
XMlX5ay8+FLCIK9M76oxwhV7VAXYbeUUZafh+xX6StWCdKrl0eJbicOGoUk/pjsi
ZjCBpK5BM0SW+s2gMSDQhO2eMsgMp9QrJMiCJHUF1wWPN8Yez6va1tg4b9iW39BZ
dd3sJq+PuN6yDbYAJIjEpiGF9gDaaYxSE6bTKJuY+oy08+VsP/RRWjorTENs9Aev
rQXZIC3nwsv26QRSX7RDSj+UE+kFV6FcPMWMU3HN2UG6ttprtOxT8tslVJf7LcA=
=BxtF
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The patch set is mostly driver updates (usf, zfcp, lpfc, mpt2sas,
megaraid_sas, bfa, ipr) and a few bug fixes. Also of note is that the
Buslogic driver has been rewritten to a better coding style and 64 bit
support added. We also removed the libsas limitation on 16 bytes for
the command size (currently no drivers make use of this)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (101 commits)
[SCSI] megaraid: minor cut and paste error fixed.
[SCSI] ufshcd-pltfrm: remove unnecessary dma_set_coherent_mask() call
[SCSI] ufs: fix register address in UIC error interrupt handling
[SCSI] ufshcd-pltfrm: add missing empty slot in ufs_of_match[]
[SCSI] ufs: use devres functions for ufshcd
[SCSI] ufs: Fix the response UPIU length setting
[SCSI] ufs: rework link start-up process
[SCSI] ufs: remove version check before IS reg clear
[SCSI] ufs: amend interrupt configuration
[SCSI] ufs: wrap the i/o access operations
[SCSI] storvsc: Update the storage protocol to win8 level
[SCSI] storvsc: Increase the value of scsi timeout for storvsc devices
[SCSI] MAINTAINERS: Add myself as the maintainer for BusLogic SCSI driver
[SCSI] BusLogic: Port driver to 64-bit.
[SCSI] BusLogic: Fix style issues
[SCSI] libiscsi: Added new boot entries in the session sysfs
[SCSI] aacraid: Fix for arrays are going offline in the system. System hangs
[SCSI] ipr: IOA Status Code(IOASC) update
[SCSI] sd: Update WRITE SAME heuristics
[SCSI] fnic: potential dead lock in fnic_is_abts_pending()
...
Update bfa driver version to 3.2.21.1
Update bfa to use firmware image versions 3.2.1.0
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Disassoicate path_tov in the driver with the dev_loss_tmo set by the
application.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch enables support for chinook quad port 16G FC card (falcon)
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow processing completions from firmware during IOC_DISABLE request is
being processed by the firmware, by setting the queue_process flag
appropriately.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Get RDS drop interrupts and REC (Read Exchange Concise) related stats
from firmware.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. While FRU VPD data update, inform firmware to send a completion event
on I2C bus. Without this change, firmware used to send completion
message on I2C bus for every chunk of FRU VPD update.
2. Support for FRU VPN update on CHINOOK2 cards.
3. Append port count to the model name to differentiate between single
port and dual port model of 1860.
4. Update the size of the model name to 16bytes
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Replaced usage of void * with u64 in data structure shared between
brocade user space libraries and the bfa driver to address pointer
size changes across 32-bit vs 64-bit to have the compatibility between
32bit library and 64bit driver and vice versa.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Root cause: When kernel crashes, On brocade 815/825 adapters,
bfa IOC state machine and FW doesn't get a notification and
hence are not cleanly shutdown. So registers holding driver/IOC
state information are not reset back to valid disabled/parking
values. This causes subsequent driver initialization to fail
during kdump kernel boot.
Fix description: during the initialization of first PCI function, reset
corresponding register when unclean shutown is detect by reading chip
registers. This will make sure that ioc/fw gets clean re-initialization.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Retry FDISC a max of 6 times. Introduce new events to handle vport
login fails due to max logins to fabric/switch.
Signed-off-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On Xen kernels, if ATC (address translation cache) is enabled, the
first PCIe DMA read from the adapter fails with an error. This is due to
a bug ASIC, which leads to a failure of 1860 ports to be initialised.
This patch includes the fix to disable Invalidated Tag Match Enable
capability by setting the bit 26 of CHIP_MISC_PRG to 0, by default it is
set to 1.
Signed-off-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update addl. fields in FDMI to confirm to FC-GS6 standard for RPA and
RHBA commands.
Signed-off-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The WARN_ON condition check in IO completion path is wrong. IOtags
returned by the firmware is compared with driver/bfa iotag after masking
the retry count bits.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
D-Port is a new port type created with the intention of running link
level diagnostic tests like loopback, traffic test. In static D-port
mode, user configures the port to D-port mode and starts the test, but
in dynamic D-port, once the Brocade switch port is configured to
D-port, it will reject the regular FLOGI from HBA with reason that it is
in D-port mode. So based on the reason code HBA port will turn itself into
D-port and start diagnostic test.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch includes changes to get FC HBA feature Forward Error
Correction (FEC) (enabled at 16Gig speed) status from firmware and to
return to brocade HBA management utility.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch includes changes to 1) Enable/disable fc credit recovery on
Brocade FC adapter port operating at max supported speed. 2) Get credit
recovery status and stats related to credit loss and recovered credits
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes two cppcheck errors in drivers/scsi/bfa/bfad_im.c
[jejb: correct strlcpy fix]
Signed-off-by: Jakob Normark <jakobnormark@gmail.com>
Acked-by: Vijay Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When you copy some code, you are supposed to read it. If nothing else,
there's a chance to spot and fix an obvious bug instead of sharing it...
X-Song: "I Got It From Agnes", by Tom Lehrer
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Tom Lehrer? You're dating yourself, Al ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Resending the patch as it didn't make the linux-scsi list.
This patch fixes fcs rport state machine to address ocassional Brocade
FC Direct Attach LUN discovery failure due to not sending PLOGI accept
to the target.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When a switch disable/enable or a reboot is done, the HBA port gets an
offline and a subsequent online notification. When the port comes up a
link up notification is sent to bfa from the firmware. The bfa then send
an FLOGI to the firmware which is sent out on the wire.
The switch port meanwhile goes offline (presumably for diagnostics)
which causes the switch not to respond to the FLOGI.
The link down notification is sent to the HBA driver. However owing to a
bug in the lps state machine handling the lps state machine does not
move to sm_init state (it remains in sm_login state and send a login
complete message to fcs). This results in a zero PID assignment as the
login is not really complete.
This fix is to correctly handle the events in lps state machine.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
he patch set is mostly driver updates (bnx2fc, ipr, lpfc, qla4) and a few bug
fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRJ0oJAAoJEDeqqVYsXL0MVVoH/A8xFiLkdCXaFkhYMlGRrDox
wgK/RwWekDOtVS2poPhDGKRfXaUn4uA3iOJig8HC5lD8NS65DElCpCWM+/DhitXt
Ky4ukgXSQ09IQtWraGqr//MC/YqM8iimWnGgXSouLPJ7a3AqYVIYCg9CEkGJX/mD
i09aE8uUyNd3Wp68anQ2w0RCH/7/InLL348WFmQ1eWxYyFJnLYGRkASbkuHxPjgU
H4QmINFlI4kBMWdHkVinh0w7cjcmUOAU+KyAZ75aelQ6dZ2aJioKn3BS7D6gF9jv
jJpJMIj8LzpAnfR3Z5ijkkcVG7E0ht+Dtr6kmAPZQJnkc/GdQvvgEg+F9aIpxoU=
=oDz4
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The patch set is mostly driver updates (bnx2fc, ipr, lpfc, qla4) and a
few bug fixes"
Pull delayed because google hates James, and sneakily considers his pull
requests spam. Why, google, why?
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (60 commits)
[SCSI] aacraid: 1024 max outstanding command support for Series 7 and above
[SCSI] bnx2fc: adjust duplicate test
[SCSI] qla4xxx: Update driver version to 5.03.00-k4
[SCSI] qla4xxx: Fix return code for qla4xxx_session_get_param.
[SCSI] qla4xxx: wait for boot target login response during probe.
[SCSI] qla4xxx: Added support for force firmware dump
[SCSI] qla4xxx: Re-register IRQ handler while retrying initialize of adapter
[SCSI] qla4xxx: Throttle active IOCBs to firmware limits
[SCSI] qla4xxx: Remove unnecessary code from qla4xxx_init_local_data
[SCSI] qla4xxx: Quiesce driver activities while loopback
[SCSI] qla4xxx: Rename MBOX_ASTS_IDC_NOTIFY to MBOX_ASTS_IDC_REQUEST_NOTIFICATION
[SCSI] qla4xxx: Add spurious interrupt messages under debug level 2
[SCSI] cxgb4i: Remove the scsi host device when removing device
[SCSI] bfa: fix strncpy() limiter in bfad_start_ops()
[SCSI] qla4xxx: Update driver version to 5.03.00-k3
[SCSI] qla4xxx: Correct the validation to check in get_sys_info mailbox
[SCSI] qla4xxx: Pass correct function param to qla4_8xxx_rd_direct
[SCSI] lpfc 8.3.37: Update lpfc version for 8.3.37 driver release
[SCSI] lpfc 8.3.37: Fixed infinite loop in lpfc_sli4_fcf_rr_next_index_get.
[SCSI] lpfc 8.3.37: Fixed crash due to SLI Port invalid resource count
...
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Krishna C Gudipati <kgudipat@brocade.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The closing parenthesis is in the wrong place so it takes the sizeof a
pointer instead of the sizeof the buffer minus one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Modified the firmware naming convention to contain the
firmware image version (3.1.0.0).
- The new convention is <firmware-image>-<firmware-version>.bin
- The change will enforce loading only compatible firmware with this driver
and also avoid over-writing the old firmware image in-order to load new
version driver as the firmware names used to be the same.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add FRU sub-module to support FRU read/write/update.
- Add support to read/write from the temp FRU module.
[jejb: fix checkpatch issues]
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add Power On Hours display support during sfpshow
- Fix to properly set the diag temperature sensor status variable.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to configure minimum bandwidth for a pcifn.
- Minimum bandwith is guaranteed at per queue level.
- Added support to update pcifn bandwidth dynamically without
a server reboot.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add capability to limit the number of exchanges on a port to
avoid queue-full conditions from the target side.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to provide an option for user to configure the
bandwidth percentage for High/Medium/Low QoS priorities.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes such that once the PWWN is acquired from the fabric through FAA,
and if the FAPWWN configuration is modified on the switch side, driver should
show relevant information to the user.
- Added logic to cache the reason code when the given port is disabled implicitl
due to FAA error condition.
- If the port is disabled, while sending SCN to upper layer, update the
reason code appropriately. With this, BFA FC port state machine will enter
into faa_err_config state. This state will be shown to the user.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced support for D-Port which is a new port mode during which
link level diagnostics can be run.
- Provided mechanism to dynamically configure D-Port and initiate diagnostic
tests to isolate any link level issues.
- In D-Port mode, the HBA port does not participate in fabric or login to the
remote device or run data traffic.
- Diagnostic tests include running various loopback tests in conjunction with
the attached device.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Enhance tracing to include both tskim tag and event.
- Handle the tskim abort response from firmware in the
tskim state machine cleanup state and proceed with the
tskim cleanup.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to set the RHBA command max payload based on
the port configured frame size.
- Made changes to fix the driver/fw version size in FMDI structure.
- Fix to pass the fw version for FDMI attribute type
FDMI_HBA_ATTRIB_FW_VERSION rather than driver version.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to expose mfg day/month/year as part of the
adapter attributes for user space applications.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to check the flash controller status before IOC initialization.
- Made changes to poll on the FLASH_STS_REG bit to check if the flash controller
initialization is completed during the PLL init.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add support to handle STOP/DISABLE events in the IOCFC state machine.
- Made changes to bring the IOC down on a flash driver config read failure.
- Added logic to clean the use count and fail sync registers during IOCFC init.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Add private loop topology support at 2G/4G/8G speeds with following
limitations
1. No support for multiple initiators in the loop
2. No public loop support. If attached to a loop with an FL_Port,
device continues to work as a private NL_Port in the loop
3. No auto topology detection. User has to manually set the
configured topology to loop if attaching to loop.
- When loop topology is configured, enabling FC port features
QoS/Trunk/TRL are not allowed and vice versa.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
- Changes to avoid discovering NPIV port as remote port by the other
NPIV ports created on same physical port when all the NPIV ports are
part of the same zone in a fabric.
- Provided mechanism to support maximum number of target ports for a
given initiator port (physical port + NPIV ports) irrespective of the
way in which the initiator and target ports are zoned in the fabric.
- Introduced module_parameter max_rport_logins to restrict number of
remote ports discovery which includes target and initiator remote ports.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Changes to register node symbolic name with name server on the fabric
by sending CT commands RNN_ID and RSNN_NN.
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to process mbox and error interrupts only if interrupts are
enabled, when running in INTx mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added few missing endian swap changes to support BFA on PowerPC.
- Added PCIE AER support to BFA:
a) Implemented the PCI error handler entry points.
b) Made changes to FCS state machine to handle STOP event from the
PCI error detected entry point.
c) Made changes to the IO Controller state machine to handle SUSPEND
event from the PCI error detected entry point.
d) Made changes to restart the BFA operations on a slot_reset completion.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added new hardware model Brocade-1867 information to
sysfs model description routine.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to split FCXP resources as request and response resources.
- The split will reduce the contention for FCXP resources in an open zone
config.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced rport qualifier structure and modified design to
export remote ports with valid pid or valid pwwn to the user space.
- Introduced old_pid field in the rport structure and made changes to
prevent re-creating a new remote port for an already existing rport
that is transitioning to a delete state. (Happens if we receive a RSCN
on the existing remote port that is getting deleted).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Implemented the FC function template set_vport_symbolic_name entry
point to modify the vport symbolic name from sysfs.
- Implemented support to send RSPN_ID to switch to register the
modified vport symbolic name.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Remove unnecessary if NULL check in function bfa_fcs_vport_free().
- Set correct return error codes in case of memory allocation failure
in the BSG ELS/CT passthru command handler.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If bfad_thread_workq(bfad) was not BFA_STATUS_OK then we freed "im"
and then dereferenced it.
I did a little clean up because it seemed nicer to return directly
instead of doing a superfluous goto. I looked at other functions in
this file and it seems like returning directly is standard.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If mc == BFI_MC_MAX then we're reading past the end of the
mod->mbhdlr[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to set the fc_host sysfs entries supported_speeds,
supported_classes etc., during the vport creation from the
FC transport template.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to have the same logging level for Logical port
online and offline events, to display these events in pairs.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make changes to remove unsupported model numbers from the sysfs
model description routine.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to avoid queuing the vport delete work to IM driver
work queue in the bfa_fcb_lport_delete() - since at this stage we
are not completely done with using the vport structure as we are
still waiting for the LOGO response from the fw in online state or
just doing some cleanup. Since queuing up the vport delete work at
this stage will result in the FC transport layer to clean up the vport
before we get the response from firmware.
Made changes to queue the port delete work to the IM driver work queue -
from the bfa_fcs_vport_free() function since at this state we are done
with using the vport data structure and the FCS state machine is completely
cleaned up.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to set the rport maxfrsize param to use a value that is
equal to or less than the Buffer-to-Buffer Receive Data_Field size
specified in the Common Service Parameters.
Increased the diag memtest timeout for the Brocade-1860 adapters.
Made changes to enable valid port speed configuration check for all adapters.
Made changes to increase the max hw segments in a request, in order to
support larger data transfers from user space.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed the LPS (Logical Port Services) state machine to send a
FDISC/FLOGI to the FW from the request queue wait state, when
there is space available again on the request queue.
Made changes to free the vport on LOGO/cleanup complete instead
of free'ing it from vport_delete_handler in the module unload scenario.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Programming of the service parameters Tx credits etc., is now done in firmware.
Remove the logic of sending the service parameters to firmware from driver.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to the Fabric Assigned Address(FAA) feature implementation.
Introduced the IOCFC state machine, which now handles the FAA logic,
IOC and BFA sub-modules enablement.
Removed un-wanted FAA enable/disable routines; FAA is enabled by default.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to resume the flash controller if it is halted before going
ahead with flash controller pause/resume logic.
Made changes to avoid clearing off the interrupts during the initial
pll initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to ensure only the function that comes first will execute
the IOC hw semaphore unlock logic.
Used IOC init sem register to serialize execution of the unlock logic.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to the driver ISR to process any pending completions even if
the RME bit is not set in the interrupt status register.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Casting pointer from native data type to other type is
endian-sensitive.
"iocmd->offset" is 64 bit but we use only first 32 bit.
It works in little-endian system but in big-endian system
it will break.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Acked-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If 'drv_fcxp = kzalloc(sizeof(struct bfad_fcxp), GFP_KERNEL);' fails
and returns NULL, then we'll leak the memory allocated to 'bsg_fcpt'
when we jump to 'out:' and the variable subsequently goes out of
scope.
Also remove the cast of the kzalloc() return value. kzalloc() returns
a void* which is implicitly converted, so the explicit cast is
pointless.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch re-implements LUN Masking feature using SCSI Slave Callouts. With
the new design in the slave_alloc entry point; for each new LUN discovered we
check with our internal LUN Masking config whether to expose or to mask this
particular LUN. We return -ENXIO (No such device or address) from slave_alloc
for the LUNs we don't want to be exposed. We also notify the SCSI mid-layer
to do a sequential LUN scan rather than REPORT_LUNS based scan if LUN masking
is enabled on our HBA port, since a -ENXIO from any LUN in REPORT_LUNS based
scan translates to a scan abort. This patch also handles the dynamic lun
masking config change from enable to disable or vice-versa by resetting
sdev_bflags of LUN 0 appropriately.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch reverts the current LUN Masking Implementation. We re-implemented
this feature using the SCSI Slave Callout's as per the review comments.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Patch fixes the possible NULL pointer dereference when we try to add or delete
a rpwwn to the lunmask config which is not zoned to this port. Check if the
FCS rport is not NULL before de-referencing it.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPBh1uAAoJEDeqqVYsXL0MnxIIAJl0SLxgX3Vo18jhv7epNaUy
Akm8VcLTjW99IAZm1x166pGjLvdeZJC5A50DxW3jQMknKYZyyxEmTGOOMVA/LuCS
J3V18tMrsEA7i1kEGx2MauRRNAvReAZl4a/nHuRc+hpVmfyQegBv1v4V0v0gzD5I
MDZSSksqtXpJhsHt2B4g/jao7RhuJYXw7NidRGzEtksax3NMyWzaIb/75Uq6eenE
HwJwCUgZZxxfRKksj/T8ShRE6BKL9wcvrm8SVNjBYF2OpnMUNCXtfLQ4fqbHtGz2
otWvoQxVERehPZhTWHk6QnLgPwBWYyIUK7ErSFMTb9EK8b3FsEZkw6/LlS/lXnI=
=Zopk
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates for post 3.2 merge window
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (67 commits)
[SCSI] lpfc 8.3.28: Update driver version to 8.3.28
[SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters
[SCSI] lpfc 8.3.28: Critical Miscellaneous fixes
[SCSI] Lpfc 8.3.28: FC and SCSI Discovery Fixes
[SCSI] lpfc 8.3.28: Add support for ABTS failure handling
[SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support
[SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces
[SCSI] mpt2sas: Removed redundant calling of _scsih_probe_devices() from _scsih_probe
[SCSI] mac_scsi: Remove obsolete IRQ_FLG_* users
[SCSI] qla4xxx: Update driver version to 5.02.00-k10
[SCSI] qla4xxx: check for FW alive before calling chip_reset
[SCSI] qla4xxx: Fix qla4xxx_dump_buffer to dump buffer correctly
[SCSI] qla4xxx: Fix the IDC locking mechanism
[SCSI] qla4xxx: Wait for disable_acb before doing set_acb
[SCSI] qla4xxx: Don't recover adapter if device state is FAILED
[SCSI] qla4xxx: fix call trace on rmmod with ql4xdontresethba=1
[SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set
[SCSI] qla4xxx: Perform context resets in case of context failures.
[SCSI] iscsi class: export pid of process that created
[SCSI] mpt2sas: Remove unused duplicate diag_buffer_enable param
...
Fix some endian issue. __BIGENDIAN is not defined and it needs to be
replaced with __BIG_ENDIAN. Also fixed a bug in bit field access.
These two issues were reported by Dan Carpenter.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/scsi/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
